diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
36 files changed, 676 insertions, 68 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index 1608a54e90e1..68ac65f82a1c 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -9,6 +9,7 @@ Required properties: - compatible : Should contain "nvidia,tegra<chip>-pmc". - reg : Offset and length of the register set for the device - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: "pclk" (The Tegra clock of that name), "clk32k_in" (The 32KHz clock input to Tegra). diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt index 0c80c2677104..9acea9d93160 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt @@ -15,6 +15,9 @@ Required properties : In clock consumers, this cell represents the clock ID exposed by the CAR. The assignments may be found in header file <dt-bindings/clock/tegra114-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. Example SoC include file: @@ -23,6 +26,7 @@ Example SoC include file: compatible = "nvidia,tegra114-car"; reg = <0x60006000 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; usb@c5004000 { diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt new file mode 100644 index 000000000000..ded5d6212c84 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt @@ -0,0 +1,63 @@ +NVIDIA Tegra124 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra124-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra124-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra124-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA124_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <112400000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt index fcfed5bf73fb..6c5901b503d0 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt @@ -15,6 +15,9 @@ Required properties : In clock consumers, this cell represents the clock ID exposed by the CAR. The assignments may be found in header file <dt-bindings/clock/tegra20-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. Example SoC include file: @@ -23,6 +26,7 @@ Example SoC include file: compatible = "nvidia,tegra20-car"; reg = <0x60006000 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; usb@c5004000 { diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt index 0f714081e986..63618cde12df 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt @@ -15,6 +15,9 @@ Required properties : In clock consumers, this cell represents the clock ID exposed by the CAR. The assignments may be found in header file <dt-bindings/clock/tegra30-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. Example SoC include file: @@ -23,6 +26,7 @@ Example SoC include file: compatible = "nvidia,tegra30-car"; reg = <0x60006000 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; usb@c5004000 { diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt index 90fa7da525b8..c6908e7c42cc 100644 --- a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt +++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt @@ -5,6 +5,16 @@ Required properties: - reg: Should contain DMA registers location and length. This shuld include all of the per-channel registers. - interrupts: Should contain all of the per-channel DMA interrupts. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - dma +- #dma-cells : Must be <1>. This dictates the length of DMA specifiers in + client nodes' dmas properties. The specifier represents the DMA request + select value for the peripheral. For more details, consult the Tegra TRM's + documentation of the APB DMA channel control register REQ_SEL field. Examples: @@ -27,4 +37,8 @@ apbdma: dma@6000a000 { 0 149 0x04 0 150 0x04 0 151 0x04 >; + clocks = <&tegra_car 34>; + resets = <&tegra_car 34>; + reset-names = "dma"; + #dma-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index b4fa934ae3a2..9e9008f8fa32 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -9,6 +9,12 @@ Required properties: - #size-cells: The number of cells used to represent the size of an address range in the host1x address space. Should be 1. - ranges: The mapping of the host1x address space to the CPU address space. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - host1x The host1x top-level node defines a number of children, each representing one of the following host1x client modules: @@ -19,6 +25,12 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-mpe" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - mpe - vi: video input @@ -26,6 +38,12 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-vi" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - vi - epp: encoder pre-processor @@ -33,6 +51,12 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-epp" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - epp - isp: image signal processor @@ -40,6 +64,12 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-isp" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - isp - gr2d: 2D graphics engine @@ -47,12 +77,30 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-gr2d" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - 2d - gr3d: 3D graphics engine Required properties: - compatible: "nvidia,tegra<chip>-gr3d" - reg: Physical base address and length of the controller's registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + (This property may be omitted if the only clock in the list is "3d") + - 3d + This MUST be the first entry. + - 3d2 (Only required on SoCs with two 3D clocks) + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - 3d + - 3d2 (Only required on SoCs with two 3D clocks) - dc: display controller @@ -60,6 +108,16 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-dc" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dc + This MUST be the first entry. + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dc Each display controller node has a child node, named "rgb", that represents the RGB output associated with the controller. It can take the following @@ -67,6 +125,7 @@ of the following host1x client modules: - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel - hdmi: High Definition Multimedia Interface @@ -76,11 +135,22 @@ of the following host1x client modules: - interrupts: The interrupt outputs from the controller. - vdd-supply: regulator for supply voltage - pll-supply: regulator for PLL + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - hdmi + This MUST be the first entry. + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - hdmi Optional properties: - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel - tvo: TV encoder output @@ -88,12 +158,34 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-tvo" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. - dsi: display serial interface Required properties: - compatible: "nvidia,tegra<chip>-dsi" - reg: Physical base address and length of the controller's registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dsi + This MUST be the first entry. + - lp + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dsi + - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying + which pads are used by this DSI output and need to be calibrated. See also + ../mipi/nvidia,tegra114-mipi.txt. + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel Example: @@ -105,6 +197,9 @@ Example: reg = <0x50000000 0x00024000>; interrupts = <0 65 0x04 /* mpcore syncpt */ 0 67 0x04>; /* mpcore general */ + clocks = <&tegra_car TEGRA20_CLK_HOST1X>; + resets = <&tegra_car 28>; + reset-names = "host1x"; #address-cells = <1>; #size-cells = <1>; @@ -115,41 +210,64 @@ Example: compatible = "nvidia,tegra20-mpe"; reg = <0x54040000 0x00040000>; interrupts = <0 68 0x04>; + clocks = <&tegra_car TEGRA20_CLK_MPE>; + resets = <&tegra_car 60>; + reset-names = "mpe"; }; vi { compatible = "nvidia,tegra20-vi"; reg = <0x54080000 0x00040000>; interrupts = <0 69 0x04>; + clocks = <&tegra_car TEGRA20_CLK_VI>; + resets = <&tegra_car 100>; + reset-names = "vi"; }; epp { compatible = "nvidia,tegra20-epp"; reg = <0x540c0000 0x00040000>; interrupts = <0 70 0x04>; + clocks = <&tegra_car TEGRA20_CLK_EPP>; + resets = <&tegra_car 19>; + reset-names = "epp"; }; isp { compatible = "nvidia,tegra20-isp"; reg = <0x54100000 0x00040000>; interrupts = <0 71 0x04>; + clocks = <&tegra_car TEGRA20_CLK_ISP>; + resets = <&tegra_car 23>; + reset-names = "isp"; }; gr2d { compatible = "nvidia,tegra20-gr2d"; reg = <0x54140000 0x00040000>; interrupts = <0 72 0x04>; + clocks = <&tegra_car TEGRA20_CLK_GR2D>; + resets = <&tegra_car 21>; + reset-names = "2d"; }; gr3d { compatible = "nvidia,tegra20-gr3d"; reg = <0x54180000 0x00040000>; + clocks = <&tegra_car TEGRA20_CLK_GR3D>; + resets = <&tegra_car 24>; + reset-names = "3d"; }; dc@54200000 { compatible = "nvidia,tegra20-dc"; reg = <0x54200000 0x00040000>; interrupts = <0 73 0x04>; + clocks = <&tegra_car TEGRA20_CLK_DISP1>, + <&tegra_car TEGRA20_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 27>; + reset-names = "dc"; rgb { status = "disabled"; @@ -160,6 +278,11 @@ Example: compatible = "nvidia,tegra20-dc"; reg = <0x54240000 0x00040000>; interrupts = <0 74 0x04>; + clocks = <&tegra_car TEGRA20_CLK_DISP2>, + <&tegra_car TEGRA20_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 26>; + reset-names = "dc"; rgb { status = "disabled"; @@ -170,6 +293,11 @@ Example: compatible = "nvidia,tegra20-hdmi"; reg = <0x54280000 0x00040000>; interrupts = <0 75 0x04>; + clocks = <&tegra_car TEGRA20_CLK_HDMI>, + <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; + clock-names = "hdmi", "parent"; + resets = <&tegra_car 51>; + reset-names = "hdmi"; status = "disabled"; }; @@ -177,12 +305,18 @@ Example: compatible = "nvidia,tegra20-tvo"; reg = <0x542c0000 0x00040000>; interrupts = <0 76 0x04>; + clocks = <&tegra_car TEGRA20_CLK_TVO>; status = "disabled"; }; dsi { compatible = "nvidia,tegra20-dsi"; reg = <0x54300000 0x00040000>; + clocks = <&tegra_car TEGRA20_CLK_DSI>, + <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; + clock-names = "dsi", "parent"; + resets = <&tegra_car 48>; + reset-names = "dsi"; status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt index ef77cc7a0e46..87507e9ce6db 100644 --- a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -39,12 +39,23 @@ Required properties: - interrupts: Should contain I2C controller interrupts. - address-cells: Address cells for I2C device address. - size-cells: Size of the I2C device address. -- clocks: Clock ID as per - Documentation/devicetree/bindings/clock/tegra<chip-id>.txt - for I2C controller. -- clock-names: Name of the clock: - Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk". - Tegra114 I2C controller: "div-clk". +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + Tegra20/Tegra30: + - div-clk + - fast-clk + Tegra114: + - div-clk +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - i2c +- dmas: Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx Example: @@ -56,5 +67,9 @@ Example: #size-cells = <0>; clocks = <&tegra_car 12>, <&tegra_car 124>; clock-names = "div-clk", "fast-clk"; + resets = <&tegra_car 12>; + reset-names = "i2c"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt index 2995fae7ee47..0382b8bd69c6 100644 --- a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt @@ -13,6 +13,12 @@ Required properties: array of pin numbers which is used as column. - linux,keymap: The keymap for keys as described in the binding document devicetree/bindings/input/matrix-keymap.txt. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - kbc Optional properties, in addition to those specified by the shared matrix-keyboard bindings: @@ -31,6 +37,9 @@ keyboard: keyboard { compatible = "nvidia,tegra20-kbc"; reg = <0x7000e200 0x100>; interrupts = <0 85 0x04>; + clocks = <&tegra_car 36>; + resets = <&tegra_car 36>; + reset-names = "kbc"; nvidia,ghost-filter; nvidia,debounce-delay-ms = <640>; nvidia,kbc-row-pins = <0 1 2>; /* pin 0, 1, 2 as rows */ diff --git a/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt b/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt new file mode 100644 index 000000000000..973c27273772 --- /dev/null +++ b/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt @@ -0,0 +1,98 @@ +MIPI DSI (Display Serial Interface) busses +========================================== + +The MIPI Display Serial Interface specifies a serial bus and a protocol for +communication between a host and up to four peripherals. This document will +define the syntax used to represent a DSI bus in a device tree. + +This document describes DSI bus-specific properties only or defines existing +standard properties in the context of the DSI bus. + +Each DSI host provides a DSI bus. The DSI host controller's node contains a +set of properties that characterize the bus. Child nodes describe individual +peripherals on that bus. + +The following assumes that only a single peripheral is connected to a DSI +host. Experience shows that this is true for the large majority of setups. + +DSI host +-------- + +In addition to the standard properties and those defined by the parent bus of +a DSI host, the following properties apply to a node representing a DSI host. + +Required properties: +- #address-cells: The number of cells required to represent an address on the + bus. DSI peripherals are addressed using a 2-bit virtual channel number, so + a maximum of 4 devices can be addressed on a single bus. Hence the value of + this property should be 1. +- #size-cells: Should be 0. There are cases where it makes sense to use a + different value here. See below. + +DSI peripheral +-------------- + +Peripherals are represented as child nodes of the DSI host's node. Properties +described here apply to all DSI peripherals, but individual bindings may want +to define additional, device-specific properties. + +Required properties: +- reg: The virtual channel number of a DSI peripheral. Must be in the range + from 0 to 3. + +Some DSI peripherals respond to more than a single virtual channel. In that +case two alternative representations can be chosen: +- The reg property can take multiple entries, one for each virtual channel + that the peripheral responds to. +- If the virtual channels that a peripheral responds to are consecutive, the + #size-cells can be set to 1. The first cell of each entry in the reg + property is the number of the first virtual channel and the second cell is + the number of consecutive virtual channels. + +Example +------- + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <0>; + + /* peripheral responds to virtual channel 0 */ + peripheral@0 { + compatible = "..."; + reg = <0>; + }; + + ... + }; + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <0>; + + /* peripheral responds to virtual channels 0 and 2 */ + peripheral@0 { + compatible = "..."; + reg = <0, 2>; + }; + + ... + }; + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <1>; + + /* peripheral responds to virtual channels 1, 2 and 3 */ + peripheral@1 { + compatible = "..."; + reg = <1 3>; + }; + + ... + }; diff --git a/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt b/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt new file mode 100644 index 000000000000..e4a25cedc5cf --- /dev/null +++ b/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt @@ -0,0 +1,41 @@ +NVIDIA Tegra MIPI pad calibration controller + +Required properties: +- compatible: "nvidia,tegra<chip>-mipi" +- reg: Physical base address and length of the controller's registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mipi-cal +- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads + that need to be calibrated for a given device. + +User nodes need to contain an nvidia,mipi-calibrate property that has a +phandle to refer to the calibration controller node and a bitmask of the pads +that need to be calibrated. + +Example: + + mipi: mipi@700e3000 { + compatible = "nvidia,tegra114-mipi"; + reg = <0x700e3000 0x100>; + clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>; + clock-names = "mipi-cal"; + #nvidia,mipi-calibrate-cells = <1>; + }; + + ... + + host1x@50000000 { + ... + + dsi@54300000 { + ... + + nvidia,mipi-calibrate = <&mipi 0x060>; + + ... + }; + + ... + }; diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index c6d7b11db9eb..f357c16ea815 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -8,6 +8,12 @@ by mmc.txt and the properties used by the sdhci-tegra driver. Required properties: - compatible : Should be "nvidia,<chip>-sdhci" +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sdhci Optional properties: - power-gpios : Specify GPIOs for power control @@ -18,6 +24,9 @@ sdhci@c8000200 { compatible = "nvidia,tegra20-sdhci"; reg = <0xc8000200 0x200>; interrupts = <47>; + clocks = <&tegra_car 14>; + resets = <&tegra_car 14>; + reset-names = "sdhci"; cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 155 0>; /* gpio PT3 */ diff --git a/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt index 5aeee53ff9f4..5ae601e7f51f 100644 --- a/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt +++ b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt @@ -7,3 +7,15 @@ Required properties: - clock-frequency : the frequency of the i2c bus - gpios : the gpio used for ec request - slave-addr: the i2c address of the slave controller +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + Tegra20/Tegra30: + - div-clk + - fast-clk + Tegra114: + - div-clk +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - i2c diff --git a/Documentation/devicetree/bindings/panel/auo,b101aw03.txt b/Documentation/devicetree/bindings/panel/auo,b101aw03.txt new file mode 100644 index 000000000000..72e088a4fb3a --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b101aw03.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101aw03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/chunghwa,claa101wb03.txt b/Documentation/devicetree/bindings/panel/chunghwa,claa101wb03.txt new file mode 100644 index 000000000000..0ab2c05a4c22 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/chunghwa,claa101wb03.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa101wb03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/panasonic,vvx10f004b00.txt b/Documentation/devicetree/bindings/panel/panasonic,vvx10f004b00.txt new file mode 100644 index 000000000000..d328b0341bf4 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/panasonic,vvx10f004b00.txt @@ -0,0 +1,7 @@ +Panasonic Corporation 10.1" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "panasonic,vvx10f004b00" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/simple-panel.txt b/Documentation/devicetree/bindings/panel/simple-panel.txt new file mode 100644 index 000000000000..1341bbf4aa3d --- /dev/null +++ b/Documentation/devicetree/bindings/panel/simple-panel.txt @@ -0,0 +1,21 @@ +Simple display panel + +Required properties: +- power-supply: regulator to provide the supply voltage + +Optional properties: +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel + +Example: + + panel: panel { + compatible = "cptt,claa101wb01"; + ddc-i2c-bus = <&panelddc>; + + power-supply = <&vdd_pnl_reg>; + enable-gpios = <&gpio 90 0>; + + backlight = <&backlight>; + }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 6b7510775c50..24cee06915c9 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -42,14 +42,19 @@ Required properties: - 0xc2000000: prefetchable memory region Please refer to the standard PCI bus binding document for a more detailed explanation. -- clocks: List of clock inputs of the controller. Must contain an entry for - each entry in the clock-names property. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - "pex": The Tegra clock of that name - "afi": The Tegra clock of that name - "pcie_xclk": The Tegra clock of that name - "pll_e": The Tegra clock of that name - "cml": The Tegra clock of that name (not required for Tegra20) + - pex + - afi + - pll_e + - cml (not required for Tegra20) +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pex + - afi + - pcie_x Root ports are defined as subnodes of the PCIe controller node. @@ -91,9 +96,10 @@ SoC DTSI: 0x82000000 0 0xa0000000 0xa0000000 0 0x10000000 /* non-prefetchable memory */ 0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */ - clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>, - <&tegra_car 118>; - clock-names = "pex", "afi", "pcie_xclk", "pll_e"; + clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>; + clock-names = "pex", "afi", "pll_e"; + resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; status = "disabled"; pci@1,0 { diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt index c3fc57af8772..c7ea9d4a988b 100644 --- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -7,6 +7,12 @@ Required properties: - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pwm Example: @@ -14,4 +20,7 @@ Example: compatible = "nvidia,tegra20-pwm"; reg = <0x7000a000 0x100>; #pwm-cells = <2>; + clocks = <&tegra_car 17>; + resets = <&tegra_car 17>; + reset-names = "pwm"; }; diff --git a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt index 93f45e9dce7c..652d1ff2e8be 100644 --- a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt @@ -9,6 +9,8 @@ Required properties: - compatible : should be "nvidia,tegra20-rtc". - reg : Specifies base physical address and size of the registers. - interrupts : A single interrupt specifier. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. Example: @@ -16,4 +18,5 @@ timer { compatible = "nvidia,tegra20-rtc"; reg = <0x7000e000 0x100>; interrupts = <0 2 0x04>; + clocks = <&tegra_car 4>; }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt index 392a4493eebd..845850caf088 100644 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -4,8 +4,17 @@ Required properties: - compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart". - reg: Should contain UART controller registers location and length. - interrupts: Should contain UART controller interrupts. -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for this UART controller. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - serial +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx Optional properties: - nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable @@ -18,7 +27,11 @@ serial@70006000 { reg = <0x70006000 0x40>; reg-shift = <2>; interrupts = <0 36 0x04>; - nvidia,dma-request-selector = <&apbdma 8>; nvidia,enable-modem-interrupt; + clocks = <&tegra_car 6>; + resets = <&tegra_car 6>; + reset-names = "serial"; + dmas = <&apbdma 8>, <&apbdma 8>; + dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt index 8b8903ef0800..57f40f93453e 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt @@ -3,10 +3,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-alc5632" - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - "pll_a" (The Tegra clock of that name), - "pll_a_out0" (The Tegra clock of that name), - "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt index dc6224994d69..7788808dcd0b 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt @@ -3,10 +3,11 @@ NVIDIA Tegra audio complex, with RT5640 CODEC Required properties: - compatible : "nvidia,tegra-audio-rt5640" - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - "pll_a" (The Tegra clock of that name), - "pll_a_out0" (The Tegra clock of that name), - "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt index aab6ce0ad2fc..96f6a57dd6b4 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt @@ -3,10 +3,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm8753" - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - "pll_a" (The Tegra clock of that name), - "pll_a_out0" (The Tegra clock of that name), - "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt index 4b44dfb6ca0d..b795d282818d 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt @@ -3,10 +3,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm8903" - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - "pll_a" (The Tegra clock of that name), - "pll_a_out0" (The Tegra clock of that name), - "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt index ad589b163639..436f6cd9d07c 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt @@ -3,10 +3,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm9712" - clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - "pll_a" (The Tegra clock of that name), - "pll_a_out0" (The Tegra clock of that name), - "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt index c1454979c1ef..eaf00102d92c 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt @@ -4,19 +4,33 @@ Required properties: - compatible : "nvidia,tegra20-ac97" - reg : Should contain AC97 controller registers location and length - interrupts : Should contain AC97 interrupt -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for the AC97 controller +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - ac97 +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. - nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number of the GPIO used to reset the external AC97 codec - nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number of the GPIO corresponding with the AC97 DAP _FS line + Example: ac97@70002000 { compatible = "nvidia,tegra20-ac97"; reg = <0x70002000 0x200>; interrupts = <0 81 0x04>; - nvidia,dma-request-selector = <&apbdma 12>; nvidia,codec-reset-gpio = <&gpio 170 0>; nvidia,codec-sync-gpio = <&gpio 120 0>; + clocks = <&tegra_car 3>; + resets = <&tegra_car 3>; + reset-names = "ac97"; + dmas = <&apbdma 12>, <&apbdma 12>; + dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt index 0df2b5c816e3..dc30c6bfbe95 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt @@ -4,8 +4,17 @@ Required properties: - compatible : "nvidia,tegra20-i2s" - reg : Should contain I2S registers location and length - interrupts : Should contain I2S interrupt -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for this I2S controller +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - i2s +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. Example: @@ -13,5 +22,9 @@ i2s@70002800 { compatible = "nvidia,tegra20-i2s"; reg = <0x70002800 0x200>; interrupts = < 45 >; - nvidia,dma-request-selector = < &apbdma 2 >; + clocks = <&tegra_car 11>; + resets = <&tegra_car 11>; + reset-names = "i2s"; + dmas = <&apbdma 21>, <&apbdma 21>; + dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt index 0e5c12c66523..946e2ac46091 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt @@ -7,18 +7,48 @@ Required properties: - Tegra30 requires 2 entries, for the APBIF and AHUB/AUDIO register blocks. - Tegra114 requires an additional entry, for the APBIF2 register block. - interrupts : Should contain AHUB interrupt -- nvidia,dma-request-selector : A list of the DMA channel specifiers. Each - entry contains the Tegra DMA controller's phandle and request selector. - If a single entry is present, the request selectors for the channels are - assumed to be contiguous, and increment from this value. - If multiple values are given, one value must be given per channel. -- clocks : Must contain an entry for each required entry in clock-names. +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entries: - - Tegra30: Requires d_audio, apbif, i2s0, i2s1, i2s2, i2s3, i2s4, dam0, - dam1, dam2, spdif_in. - - Tegra114: Additionally requires amx, adx. + - d_audio + - apbif +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + Tegra30 and later: + - d_audio + - apbif + - i2s0 + - i2s1 + - i2s2 + - i2s3 + - i2s4 + - dam0 + - dam1 + - dam2 + - spdif + Tegra114 and later additionally require: + - amx + - adx + Tegra124 and later additionally require: + - amx1 + - adx1 + - afc0 + - afc1 + - afc2 + - afc3 + - afc4 + - afc5 - ranges : The bus address mapping for the configlink register bus. Can be empty since the mapping is 1:1. +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx0 .. rx<n> + - tx0 .. tx<n> + ... where n is: + Tegra30: 3 + Tegra114, Tegra124: 9 - #address-cells : For the configlink bus. Should be <1>; - #size-cells : For the configlink bus. Should be <1>. @@ -35,13 +65,20 @@ ahub@70080000 { reg = <0x70080000 0x200 0x70080200 0x100>; interrupts = < 0 103 0x04 >; nvidia,dma-request-selector = <&apbdma 1>; - clocks = <&tegra_car 106>, <&tegra_car 107>, <&tegra_car 30>, + clocks = <&tegra_car 106>, <&tegra_car 107>; + clock-names = "d_audio", "apbif"; + resets = <&tegra_car 106>, <&tegra_car 107>, <&tegra_car 30>, <&tegra_car 11>, <&tegra_car 18>, <&tegra_car 101>, <&tegra_car 102>, <&tegra_car 108>, <&tegra_car 109>, - <&tegra_car 110>, <&tegra_car 162>; - clock-names = "d_audio", "apbif", "i2s0", "i2s1", "i2s2", + <&tegra_car 110>, <&tegra_car 10>; + reset-names = "d_audio", "apbif", "i2s0", "i2s1", "i2s2", "i2s3", "i2s4", "dam0", "dam1", "dam2", - "spdif_in"; + "spdif"; + dmas = <&apbdma 1>, <&apbdma 1>; + <&apbdma 2>, <&apbdma 2>; + <&apbdma 3>, <&apbdma 3>; + <&apbdma 4>, <&apbdma 4>; + dma-names = "rx0", "tx0", "rx1", "tx1", "rx2", "tx2", "rx3", "tx3"; ranges; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt index dfa6c037124a..0c113ffe3814 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt @@ -3,13 +3,22 @@ NVIDIA Tegra30 I2S controller Required properties: - compatible : "nvidia,tegra30-i2s" - reg : Should contain I2S registers location and length +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - i2s - nvidia,ahub-cif-ids : The list of AHUB CIF IDs for this port, rx (playback) first, tx (capture) second. See nvidia,tegra30-ahub.txt for values. Example: -i2s@70002800 { +i2s@70080300 { compatible = "nvidia,tegra30-i2s"; reg = <0x70080300 0x100>; nvidia,ahub-cif-ids = <4 4>; + clocks = <&tegra_car 11>; + resets = <&tegra_car 11>; + reset-names = "i2s"; }; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt index 91ff771c7e77..7ea701e07dc2 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -4,10 +4,19 @@ Required properties: - compatible : should be "nvidia,tegra114-spi". - reg: Should contain SPI registers location and length. - interrupts: Should contain SPI interrupts. -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for this SPI controller. -- This is also require clock named "spi" as per binding document - Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names : Must include the following entries: + - spi +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. Recommended properties: - spi-max-frequency: Definition as per @@ -18,9 +27,14 @@ spi@7000d600 { compatible = "nvidia,tegra114-spi"; reg = <0x7000d600 0x200>; interrupts = <0 82 0x04>; - nvidia,dma-request-selector = <&apbdma 16>; spi-max-frequency = <25000000>; #address-cells = <1>; #size-cells = <0>; + clocks = <&tegra_car 44>; + clock-names = "spi"; + resets = <&tegra_car 44>; + reset-names = "spi"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt index 7b53da5cb75b..bdf08e6dec9b 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -4,8 +4,17 @@ Required properties: - compatible : should be "nvidia,tegra20-sflash". - reg: Should contain SFLASH registers location and length. - interrupts: Should contain SFLASH interrupts. -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for this SFLASH controller. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx Recommended properties: - spi-max-frequency: Definition as per @@ -17,10 +26,13 @@ spi@7000c380 { compatible = "nvidia,tegra20-sflash"; reg = <0x7000c380 0x80>; interrupts = <0 39 0x04>; - nvidia,dma-request-selector = <&apbdma 16>; spi-max-frequency = <25000000>; #address-cells = <1>; #size-cells = <0>; + clocks = <&tegra_car 43>; + resets = <&tegra_car 43>; + reset-names = "spi"; + dmas = <&apbdma 11>, <&apbdma 11>; + dma-names = "rx", "tx"; status = "disabled"; }; - diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt index eefe15e3d95e..5db9144a33c8 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -4,8 +4,17 @@ Required properties: - compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink". - reg: Should contain SLINK registers location and length. - interrupts: Should contain SLINK interrupts. -- nvidia,dma-request-selector : The Tegra DMA controller's phandle and - request selector for this SLINK controller. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx Recommended properties: - spi-max-frequency: Definition as per @@ -17,10 +26,13 @@ spi@7000d600 { compatible = "nvidia,tegra20-slink"; reg = <0x7000d600 0x200>; interrupts = <0 82 0x04>; - nvidia,dma-request-selector = <&apbdma 16>; spi-max-frequency = <25000000>; #address-cells = <1>; #size-cells = <0>; + clocks = <&tegra_car 44>; + resets = <&tegra_car 44>; + reset-names = "spi"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; status = "disabled"; }; - diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt index e019fdc38773..4a864bd10d3d 100644 --- a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt @@ -8,6 +8,8 @@ Required properties: - compatible : should be "nvidia,tegra20-timer". - reg : Specifies base physical address and size of the registers. - interrupts : A list of 4 interrupts; one per timer channel. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. Example: @@ -18,4 +20,5 @@ timer { 0 1 0x04 0 41 0x04 0 42 0x04>; + clocks = <&tegra_car 132>; }; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt index 906109d4c593..b5082a1cf461 100644 --- a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt @@ -10,6 +10,8 @@ Required properties: - reg : Specifies base physical address and size of the registers. - interrupts : A list of 6 interrupts; one per each of timer channels 1 through 5, and one for the shared interrupt for the remaining channels. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. timer { compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer"; @@ -20,4 +22,5 @@ timer { 0 42 0x04 0 121 0x04 0 122 0x04>; + clocks = <&tegra_car 214>; }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index df0933043a5b..3dc9140e3dfb 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -8,7 +8,12 @@ and additions : Required properties : - compatible : Should be "nvidia,tegra20-ehci". - nvidia,phy : phandle of the PHY that the controller is connected to. - - clocks : Contains a single entry which defines the USB controller's clock. + - clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Must include the following entries: + - usb Optional properties: - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20 |