1 files changed, 0 insertions, 132 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
deleted file mode 100644
index eccbe3f55d3f..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
+++ /dev/null
@@ -1,132 +0,0 @@
-* Mediatek MT8183 Pin Controller
-
-The Mediatek's Pin controller is used to control SoC pins.
-
-Required properties:
-- compatible: value should be one of the following.
-	"mediatek,mt8183-pinctrl", compatible with mt8183 pinctrl.
-- gpio-controller : Marks the device node as a gpio controller.
-- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
-  binding is used, the amount of cells must be specified as 2. See the below
-  mentioned gpio binding representation for description of particular cells.
-- gpio-ranges : gpio valid number range.
-- reg: physical address base for gpio base registers. There are 10 GPIO
-  physical address base in mt8183.
-
-Optional properties:
-- reg-names: gpio base register names. There are 10 gpio base register
-  names in mt8183. They are "iocfg0", "iocfg1", "iocfg2", "iocfg3", "iocfg4",
-  "iocfg5", "iocfg6", "iocfg7", "iocfg8", "eint".
-- interrupt-controller: Marks the device node as an interrupt controller
-- #interrupt-cells: Should be two.
-- interrupts : The interrupt outputs to sysirq.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices.
-
-Subnode format
-A pinctrl node should contain at least one subnodes representing the
-pinctrl groups available on the machine. Each subnode will list the
-pins it needs, and how they should be configured, with regard to muxer
-configuration, pullups, drive strength, input enable/disable and input schmitt.
-
-    node {
-	pinmux = <PIN_NUMBER_PINMUX>;
-	GENERIC_PINCONFIG;
-    };
-
-Required properties:
-- pinmux: integer array, represents gpio pin number and mux setting.
-    Supported pin number and mux varies for different SoCs, and are defined
-    as macros in boot/dts/<soc>-pinfunc.h directly.
-
-Optional properties:
-- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
-    bias-pull-down, bias-pull-up, input-enable, input-disable, output-low,
-    output-high, input-schmitt-enable, input-schmitt-disable
-    and drive-strength are valid.
-
-    Some special pins have extra pull up strength, there are R0 and R1 pull-up
-    resistors available, but for user, it's only need to set R1R0 as 00, 01,
-    10 or 11. So It needs config "mediatek,pull-up-adv" or
-    "mediatek,pull-down-adv" to support arguments for those special pins.
-    Valid arguments are from 0 to 3.
-
-    mediatek,tdsel: An integer describing the steps for output level shifter
-      duty cycle when asserted (high pulse width adjustment). Valid arguments
-      are from 0 to 15.
-    mediatek,rdsel: An integer describing the steps for input level shifter
-      duty cycle when asserted (high pulse width adjustment). Valid arguments
-      are from 0 to 63.
-
-    When config drive-strength, it can support some arguments, such as
-    MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
-    It can only support 2/4/6/8/10/12/14/16mA in mt8183.
-    For I2C pins, there are existing generic driving setup and the specific
-    driving setup. I2C pins can only support 2/4/6/8/10/12/14/16mA driving
-    adjustment in generic driving setup. But in specific driving setup,
-    they can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
-    driving setup for I2C pins, the existing generic driving setup will be
-    disabled. For some special features, we need the I2C pins specific
-    driving setup. The specific driving setup is controlled by E1E0EN.
-    So we need add extra vendor driving preperty instead of
-    the generic driving property.
-    We can add "mediatek,drive-strength-adv = <XXX>;" to describe the specific
-    driving setup property. "XXX" means the value of E1E0EN. EN is 0 or 1.
-    It is used to enable or disable the specific driving setup.
-    E1E0 is used to describe the detail strength specification of the I2C pin.
-    When E1=0/E0=0, the strength is 0.125mA.
-    When E1=0/E0=1, the strength is 0.25mA.
-    When E1=1/E0=0, the strength is 0.5mA.
-    When E1=1/E0=1, the strength is 1mA.
-    So the valid arguments of "mediatek,drive-strength-adv" are from 0 to 7.
-
-Examples:
-
-#include "mt8183-pinfunc.h"
-
-...
-{
-	pio: pinctrl@10005000 {
-		compatible = "mediatek,mt8183-pinctrl";
-		reg = <0 0x10005000 0 0x1000>,
-		      <0 0x11f20000 0 0x1000>,
-		      <0 0x11e80000 0 0x1000>,
-		      <0 0x11e70000 0 0x1000>,
-		      <0 0x11e90000 0 0x1000>,
-		      <0 0x11d30000 0 0x1000>,
-		      <0 0x11d20000 0 0x1000>,
-		      <0 0x11c50000 0 0x1000>,
-		      <0 0x11f30000 0 0x1000>,
-		      <0 0x1000b000 0 0x1000>;
-		reg-names = "iocfg0", "iocfg1", "iocfg2",
-			    "iocfg3", "iocfg4", "iocfg5",
-			    "iocfg6", "iocfg7", "iocfg8",
-			    "eint";
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&pio 0 0 192>;
-		interrupt-controller;
-		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
-		#interrupt-cells = <2>;
-
-		i2c0_pins_a: i2c0 {
-			pins1 {
-				pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
-					 <PINMUX_GPIO49__FUNC_SDA5>;
-				mediatek,pull-up-adv = <3>;
-				mediatek,drive-strength-adv = <7>;
-			};
-		};
-
-		i2c1_pins_a: i2c1 {
-			pins {
-				pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
-					 <PINMUX_GPIO51__FUNC_SDA3>;
-				mediatek,pull-down-adv = <2>;
-				mediatek,drive-strength-adv = <4>;
-			};
-		};
-		...
-	};
-};