diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
20 files changed, 1055 insertions, 446 deletions
diff --git a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt deleted file mode 100644 index 8ba9ed11d716..000000000000 --- a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt +++ /dev/null @@ -1,23 +0,0 @@ -* Broadcom iProc MDIO bus controller - -Required properties: -- compatible: should be "brcm,iproc-mdio" -- reg: address and length of the register set for the MDIO interface -- #size-cells: must be 1 -- #address-cells: must be 0 - -Child nodes of this MDIO bus controller node are standard Ethernet PHY device -nodes as described in Documentation/devicetree/bindings/net/phy.txt - -Example: - -mdio@18002000 { - compatible = "brcm,iproc-mdio"; - reg = <0x18002000 0x8>; - #size-cells = <1>; - #address-cells = <0>; - - enet-gphy@0 { - reg = <0>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.yaml b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.yaml new file mode 100644 index 000000000000..3031395f7e6e --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.yaml @@ -0,0 +1,38 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/brcm,iproc-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom iProc MDIO bus controller + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +allOf: + - $ref: mdio.yaml# + +properties: + compatible: + const: brcm,iproc-mdio + + reg: + maxItems: 1 + +unevaluatedProperties: false + +required: + - reg + +examples: + - | + mdio@18002000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18002000 0x8>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt deleted file mode 100644 index 90ac4fef23f5..000000000000 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ /dev/null @@ -1,80 +0,0 @@ -Renesas R-Car CAN controller Device Tree Bindings -------------------------------------------------- - -Required properties: -- compatible: "renesas,can-r8a7742" if CAN controller is a part of R8A7742 SoC. - "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC. - "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC. - "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. - "renesas,can-r8a77470" if CAN controller is a part of R8A77470 SoC. - "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC. - "renesas,can-r8a774b1" if CAN controller is a part of R8A774B1 SoC. - "renesas,can-r8a774c0" if CAN controller is a part of R8A774C0 SoC. - "renesas,can-r8a774e1" if CAN controller is a part of R8A774E1 SoC. - "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. - "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. - "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. - "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. - "renesas,can-r8a7792" if CAN controller is a part of R8A7792 SoC. - "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC. - "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. - "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. - "renesas,can-r8a7796" if CAN controller is a part of R8A77960 SoC. - "renesas,can-r8a77961" if CAN controller is a part of R8A77961 SoC. - "renesas,can-r8a77965" if CAN controller is a part of R8A77965 SoC. - "renesas,can-r8a77990" if CAN controller is a part of R8A77990 SoC. - "renesas,can-r8a77995" if CAN controller is a part of R8A77995 SoC. - "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. - "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1 - compatible device. - "renesas,rcar-gen3-can" for a generic R-Car Gen3 or RZ/G2 - compatible device. - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first - followed by the generic version. - -- reg: physical base address and size of the R-Car CAN register map. -- interrupts: interrupt specifier for the sole interrupt. -- clocks: phandles and clock specifiers for 3 CAN clock inputs. -- clock-names: 3 clock input name strings: "clkp1", "clkp2", and "can_clk". -- pinctrl-0: pin control group to be used for this controller. -- pinctrl-names: must be "default". - -Required properties for R8A774A1, R8A774B1, R8A774C0, R8A774E1, R8A7795, -R8A77960, R8A77961, R8A77965, R8A77990, and R8A77995: -For the denoted SoCs, "clkp2" can be CANFD clock. This is a div6 clock and can -be used by both CAN and CAN FD controller at the same time. It needs to be -scaled to maximum frequency if any of these controllers use it. This is done -using the below properties: - -- assigned-clocks: phandle of clkp2(CANFD) clock. -- assigned-clock-rates: maximum frequency of this clock. - -Optional properties: -- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: - <0x0> (default) : Peripheral clock (clkp1) - <0x1> : Peripheral clock (clkp2) - <0x3> : External input clock - -Example -------- - -SoC common .dtsi file: - - can0: can@e6e80000 { - compatible = "renesas,can-r8a7791", "renesas,rcar-gen2-can"; - reg = <0 0xe6e80000 0 0x1000>; - interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, - <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; - clock-names = "clkp1", "clkp2", "can_clk"; - status = "disabled"; - }; - -Board specific .dts file: - -&can0 { - pinctrl-0 = <&can0_pins>; - pinctrl-names = "default"; - status = "okay"; -}; diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt deleted file mode 100644 index 248c4ed97a0a..000000000000 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ /dev/null @@ -1,107 +0,0 @@ -Renesas R-Car CAN FD controller Device Tree Bindings ----------------------------------------------------- - -Required properties: -- compatible: Must contain one or more of the following: - - "renesas,rcar-gen3-canfd" for R-Car Gen3 and RZ/G2 compatible controllers. - - "renesas,r8a774a1-canfd" for R8A774A1 (RZ/G2M) compatible controller. - - "renesas,r8a774b1-canfd" for R8A774B1 (RZ/G2N) compatible controller. - - "renesas,r8a774c0-canfd" for R8A774C0 (RZ/G2E) compatible controller. - - "renesas,r8a774e1-canfd" for R8A774E1 (RZ/G2H) compatible controller. - - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. - - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. - - "renesas,r8a77965-canfd" for R8A77965 (R-Car M3-N) compatible controller. - - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. - - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. - - "renesas,r8a77990-canfd" for R8A77990 (R-Car E3) compatible controller. - - "renesas,r8a77995-canfd" for R8A77995 (R-Car D3) compatible controller. - - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first, followed by the - family-specific and/or generic versions. - -- reg: physical base address and size of the R-Car CAN FD register map. -- interrupts: interrupt specifiers for the Channel & Global interrupts -- clocks: phandles and clock specifiers for 3 clock inputs. -- clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". -- pinctrl-0: pin control group to be used for this controller. -- pinctrl-names: must be "default". - -Required child nodes: -The controller supports two channels and each is represented as a child node. -The name of the child nodes are "channel0" and "channel1" respectively. Each -child node supports the "status" property only, which is used to -enable/disable the respective channel. - -Required properties for R8A774A1, R8A774B1, R8A774C0, R8A774E1, R8A7795, -R8A7796, R8A77965, R8A77990, and R8A77995: -In the denoted SoCs, canfd clock is a div6 clock and can be used by both CAN -and CAN FD controller at the same time. It needs to be scaled to maximum -frequency if any of these controllers use it. This is done using the below -properties: - -- assigned-clocks: phandle of canfd clock. -- assigned-clock-rates: maximum frequency of this clock. - -Optional property: -The controller can operate in either CAN FD only mode (default) or -Classical CAN only mode. The mode is global to both the channels. In order to -enable the later, define the following optional property. - - renesas,no-can-fd: puts the controller in Classical CAN only mode. - -Example -------- - -SoC common .dtsi file: - - canfd: can@e66c0000 { - compatible = "renesas,r8a7795-canfd", - "renesas,rcar-gen3-canfd"; - reg = <0 0xe66c0000 0 0x8000>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 914>, - <&cpg CPG_CORE R8A7795_CLK_CANFD>, - <&can_clk>; - clock-names = "fck", "canfd", "can_clk"; - assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; - assigned-clock-rates = <40000000>; - power-domains = <&cpg>; - status = "disabled"; - - channel0 { - status = "disabled"; - }; - - channel1 { - status = "disabled"; - }; - }; - -Board specific .dts file: - -E.g. below enables Channel 1 alone in the board in Classical CAN only mode. - -&canfd { - pinctrl-0 = <&canfd1_pins>; - pinctrl-names = "default"; - renesas,no-can-fd; - status = "okay"; - - channel1 { - status = "okay"; - }; -}; - -E.g. below enables Channel 0 alone in the board using External clock -as fCAN clock. - -&canfd { - pinctrl-0 = <&canfd0_pins>, <&can_clk_pins>; - pinctrl-names = "default"; - status = "okay"; - - channel0 { - status = "okay"; - }; -}; diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-can.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-can.yaml new file mode 100644 index 000000000000..fadc871fd6b0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-can.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/renesas,rcar-can.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car CAN Controller + +maintainers: + - Sergei Shtylyov <sergei.shtylyov@gmail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,can-r8a7778 # R-Car M1-A + - renesas,can-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-can # R-Car Gen1 + + - items: + - enum: + - renesas,can-r8a7742 # RZ/G1H + - renesas,can-r8a7743 # RZ/G1M + - renesas,can-r8a7744 # RZ/G1N + - renesas,can-r8a7745 # RZ/G1E + - renesas,can-r8a77470 # RZ/G1C + - renesas,can-r8a7790 # R-Car H2 + - renesas,can-r8a7791 # R-Car M2-W + - renesas,can-r8a7792 # R-Car V2H + - renesas,can-r8a7793 # R-Car M2-N + - renesas,can-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-can # R-Car Gen2 and RZ/G1 + + - items: + - enum: + - renesas,can-r8a774a1 # RZ/G2M + - renesas,can-r8a774b1 # RZ/G2N + - renesas,can-r8a774c0 # RZ/G2E + - renesas,can-r8a774e1 # RZ/G2H + - renesas,can-r8a7795 # R-Car H3 + - renesas,can-r8a7796 # R-Car M3-W + - renesas,can-r8a77961 # R-Car M3-W+ + - renesas,can-r8a77965 # R-Car M3-N + - renesas,can-r8a77990 # R-Car E3 + - renesas,can-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-can # R-Car Gen3 and RZ/G2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 3 + + clock-names: + items: + - const: clkp1 + - const: clkp2 + - const: can_clk + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + renesas,can-clock-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 3 ] + default: 0 + description: | + R-Car CAN Clock Source Select. Valid values are: + <0x0> (default) : Peripheral clock (clkp1) + <0x1> : Peripheral clock (clkp2) + <0x3> : External input clock + + assigned-clocks: + description: + Reference to the clkp2 (CANFD) clock. + On R-Car Gen3 and RZ/G2 SoCs, "clkp2" is the CANFD clock. This is a div6 + clock and can be used by both CAN and CAN FD controllers at the same + time. It needs to be scaled to maximum frequency if any of these + controllers use it. + + assigned-clock-rates: + description: Maximum frequency of the CANFD clock. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +allOf: + - $ref: can-controller.yaml# + + - if: + not: + properties: + compatible: + contains: + const: renesas,rcar-gen1-can + then: + required: + - resets + + - if: + properties: + compatible: + contains: + const: renesas,rcar-gen3-can + then: + required: + - assigned-clocks + - assigned-clock-rates + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7791-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7791-sysc.h> + + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791", "renesas,rcar-gen2-can"; + reg = <0xe6e80000 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 916>, + <&cpg CPG_CORE R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 916>; + }; diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml new file mode 100644 index 000000000000..0b33ba9ccb47 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/renesas,rcar-canfd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car CAN FD Controller + +maintainers: + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> + +allOf: + - $ref: can-controller.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r8a774a1-canfd # RZ/G2M + - renesas,r8a774b1-canfd # RZ/G2N + - renesas,r8a774c0-canfd # RZ/G2E + - renesas,r8a774e1-canfd # RZ/G2H + - renesas,r8a7795-canfd # R-Car H3 + - renesas,r8a7796-canfd # R-Car M3-W + - renesas,r8a77965-canfd # R-Car M3-N + - renesas,r8a77970-canfd # R-Car V3M + - renesas,r8a77980-canfd # R-Car V3H + - renesas,r8a77990-canfd # R-Car E3 + - renesas,r8a77995-canfd # R-Car D3 + - const: renesas,rcar-gen3-canfd # R-Car Gen3 and RZ/G2 + + reg: + maxItems: 1 + + interrupts: + items: + - description: Channel interrupt + - description: Global interrupt + + clocks: + maxItems: 3 + + clock-names: + items: + - const: fck + - const: canfd + - const: can_clk + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + renesas,no-can-fd: + $ref: /schemas/types.yaml#/definitions/flag + description: + The controller can operate in either CAN FD only mode (default) or + Classical CAN only mode. The mode is global to both the channels. + Specify this property to put the controller in Classical CAN only mode. + + assigned-clocks: + description: + Reference to the CANFD clock. The CANFD clock is a div6 clock and can be + used by both CAN (if present) and CAN FD controllers at the same time. + It needs to be scaled to maximum frequency if any of these controllers + use it. + + assigned-clock-rates: + description: Maximum frequency of the CANFD clock. + +patternProperties: + "^channel[01]$": + type: object + description: + The controller supports two channels and each is represented as a child + node. Each child node supports the "status" property only, which + is used to enable/disable the respective channel. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - resets + - assigned-clocks + - assigned-clock-rates + - channel0 + - channel1 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + canfd: can@e66c0000 { + compatible = "renesas,r8a7795-canfd", + "renesas,rcar-gen3-canfd"; + reg = <0xe66c0000 0x8000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 914>, + <&cpg CPG_CORE R8A7795_CLK_CANFD>, + <&can_clk>; + clock-names = "fck", "canfd", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 914>; + + channel0 { + }; + + channel1 { + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt index de04626a8e9d..18247ebfc487 100644 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -81,6 +81,12 @@ Optional properties: - gpio-controller: Boolean; if defined, MT7530's LED controller will run on GPIO mode. - #gpio-cells: Must be 2 if gpio-controller is defined. +- interrupt-controller: Boolean; Enables the internal interrupt controller. + +If interrupt-controller is defined, the following properties are required. + +- #interrupt-cells: Must be 1. +- interrupts: Parent interrupt for the interrupt controller. See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required, optional properties and how the integrated switch subnodes must diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml new file mode 100644 index 000000000000..0b8a05dd52e6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP SJA1105 Automotive Ethernet Switch Family Device Tree Bindings + +description: + The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at + least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum + cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed + depends on the SPI bus master driver. + +allOf: + - $ref: "dsa.yaml#" + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + +properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105t + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1110a + - nxp,sja1110b + - nxp,sja1110c + - nxp,sja1110d + + reg: + maxItems: 1 + + # Optional container node for the 2 internal MDIO buses of the SJA1110 + # (one for the internal 100base-T1 PHYs and the other for the single + # 100base-TX PHY). The "reg" property does not have physical significance. + # The PHY addresses to port correspondence is as follows: for 100base-T1, + # port 5 has PHY 1, port 6 has PHY 2 etc, while for 100base-TX, port 1 has + # PHY 1. + mdios: + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^mdio@[0-1]$": + type: object + + allOf: + - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" + + properties: + compatible: + oneOf: + - enum: + - nxp,sja1110-base-t1-mdio + - nxp,sja1110-base-tx-mdio + + reg: + oneOf: + - enum: + - 0 + - 1 + + required: + - compatible + - reg + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@1 { + reg = <0x1>; + compatible = "nxp,sja1105t"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + phy-handle = <&rgmii_phy6>; + phy-mode = "rgmii-id"; + reg = <0>; + }; + + port@1 { + phy-handle = <&rgmii_phy3>; + phy-mode = "rgmii-id"; + reg = <1>; + }; + + port@2 { + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + reg = <2>; + }; + + port@3 { + phy-mode = "rgmii-id"; + reg = <3>; + }; + + port@4 { + ethernet = <&enet2>; + phy-mode = "rgmii"; + reg = <4>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index ccbc6d89325d..8c73f67c43ca 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -3,6 +3,7 @@ Required properties: - compatible: should be one of: + "qca,qca8327" "qca,qca8334" "qca,qca8337" @@ -20,6 +21,10 @@ described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external mdio-bus each subnode describing a port needs to have a valid phandle referencing the internal PHY it is connected to. This is because there's no N:N mapping of port and PHY id. +To declare the internal mdio-bus configuration, declare a mdio node in the +switch node and declare the phandle for the port referencing the internal +PHY is connected to. In this config a internal mdio-bus is registered and +the mdio MASTER is used as communication. Don't use mixed external and internal mdio-bus configurations, as this is not supported by the hardware. @@ -149,26 +154,61 @@ for the internal master mdio-bus configuration: port@1 { reg = <1>; label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy_port1>; }; port@2 { reg = <2>; label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy_port2>; }; port@3 { reg = <3>; label = "lan3"; + phy-mode = "internal"; + phy-handle = <&phy_port3>; }; port@4 { reg = <4>; label = "lan4"; + phy-mode = "internal"; + phy-handle = <&phy_port4>; }; port@5 { reg = <5>; label = "wan"; + phy-mode = "internal"; + phy-handle = <&phy_port5>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; }; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt deleted file mode 100644 index 13fd21074d48..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/sja1105.txt +++ /dev/null @@ -1,156 +0,0 @@ -NXP SJA1105 switch driver -========================= - -Required properties: - -- compatible: - Must be one of: - - "nxp,sja1105e" - - "nxp,sja1105t" - - "nxp,sja1105p" - - "nxp,sja1105q" - - "nxp,sja1105r" - - "nxp,sja1105s" - - Although the device ID could be detected at runtime, explicit bindings - are required in order to be able to statically check their validity. - For example, SGMII can only be specified on port 4 of R and S devices, - and the non-SGMII devices, while pin-compatible, are not equal in terms - of support for RGMII internal delays (supported on P/Q/R/S, but not on - E/T). - -Optional properties: - -- sja1105,role-mac: -- sja1105,role-phy: - Boolean properties that can be assigned under each port node. By - default (unless otherwise specified) a port is configured as MAC if it - is driving a PHY (phy-handle is present) or as PHY if it is PHY-less - (fixed-link specified, presumably because it is connected to a MAC). - The effect of this property (in either its implicit or explicit form) - is: - - In the case of MII or RMII it specifies whether the SJA1105 port is a - clock source or sink for this interface (not applicable for RGMII - where there is a Tx and an Rx clock). - - In the case of RGMII it affects the behavior regarding internal - delays: - 1. If sja1105,role-mac is specified, and the phy-mode property is one - of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity - designated to apply the delay/clock skew necessary for RGMII - is the PHY. The SJA1105 MAC does not apply any internal delays. - 2. If sja1105,role-phy is specified, and the phy-mode property is one - of the above, the designated entity to apply the internal delays - is the SJA1105 MAC (if hardware-supported). This is only supported - by the second-generation (P/Q/R/S) hardware. On a first-generation - E or T device, it is an error to specify an RGMII phy-mode other - than "rgmii" for a port that is in fixed-link mode. In that case, - the clock skew must either be added by the MAC at the other end of - the fixed-link, or by PCB serpentine traces on the board. - These properties are required, for example, in the case where SJA1105 - ports are at both ends of a MII/RMII PHY-less setup. One end would need - to have sja1105,role-mac, while the other sja1105,role-phy. - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard -DSA required and optional properties. - -Other observations ------------------- - -The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least -one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum -cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed -depends on the SPI bus master driver. - -Example -------- - -Ethernet switch connected via SPI to the host, CPU port wired to enet2: - -arch/arm/boot/dts/ls1021a-tsn.dts: - -/* SPI controller of the LS1021 */ -&dspi0 { - sja1105@1 { - reg = <0x1>; - #address-cells = <1>; - #size-cells = <0>; - compatible = "nxp,sja1105t"; - spi-max-frequency = <4000000>; - fsl,spi-cs-sck-delay = <1000>; - fsl,spi-sck-cs-delay = <1000>; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - /* ETH5 written on chassis */ - label = "swp5"; - phy-handle = <&rgmii_phy6>; - phy-mode = "rgmii-id"; - reg = <0>; - /* Implicit "sja1105,role-mac;" */ - }; - port@1 { - /* ETH2 written on chassis */ - label = "swp2"; - phy-handle = <&rgmii_phy3>; - phy-mode = "rgmii-id"; - reg = <1>; - /* Implicit "sja1105,role-mac;" */ - }; - port@2 { - /* ETH3 written on chassis */ - label = "swp3"; - phy-handle = <&rgmii_phy4>; - phy-mode = "rgmii-id"; - reg = <2>; - /* Implicit "sja1105,role-mac;" */ - }; - port@3 { - /* ETH4 written on chassis */ - phy-handle = <&rgmii_phy5>; - label = "swp4"; - phy-mode = "rgmii-id"; - reg = <3>; - /* Implicit "sja1105,role-mac;" */ - }; - port@4 { - /* Internal port connected to eth2 */ - ethernet = <&enet2>; - phy-mode = "rgmii"; - reg = <4>; - /* Implicit "sja1105,role-phy;" */ - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; -}; - -/* MDIO controller of the LS1021 */ -&mdio0 { - /* BCM5464 */ - rgmii_phy3: ethernet-phy@3 { - reg = <0x3>; - }; - rgmii_phy4: ethernet-phy@4 { - reg = <0x4>; - }; - rgmii_phy5: ethernet-phy@5 { - reg = <0x5>; - }; - rgmii_phy6: ethernet-phy@6 { - reg = <0x6>; - }; -}; - -/* Ethernet master port of the LS1021 */ -&enet2 { - phy-connection-type = "rgmii"; - status = "ok"; - fixed-link { - speed = <1000>; - full-duplex; - }; -}; diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml index e8f04687a3e0..b0933a8c295a 100644 --- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml @@ -68,6 +68,7 @@ properties: - tbi - rev-mii - rmii + - rev-rmii # RX and TX delays are added by the MAC when required - rgmii @@ -97,6 +98,7 @@ properties: - 10gbase-kr - usxgmii - 10gbase-r + - 25gbase-r phy-mode: $ref: "#/properties/phy-connection-type" diff --git a/Documentation/devicetree/bindings/net/ingenic,mac.yaml b/Documentation/devicetree/bindings/net/ingenic,mac.yaml new file mode 100644 index 000000000000..d08a88125a5c --- /dev/null +++ b/Documentation/devicetree/bindings/net/ingenic,mac.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ingenic,mac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for MAC in Ingenic SoCs + +maintainers: + - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> + +description: + The Ethernet Media Access Controller in Ingenic SoCs. + +properties: + compatible: + enum: + - ingenic,jz4775-mac + - ingenic,x1000-mac + - ingenic,x1600-mac + - ingenic,x1830-mac + - ingenic,x2000-mac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-names: + const: macirq + + clocks: + maxItems: 1 + + clock-names: + const: stmmaceth + + mode-reg: + description: An extra syscon register that control ethernet interface and timing delay + + rx-clk-delay-ps: + description: RGMII receive clock delay defined in pico seconds + + tx-clk-delay-ps: + description: RGMII transmit clock delay defined in pico seconds + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - mode-reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/x1000-cgu.h> + + mac: ethernet@134b0000 { + compatible = "ingenic,x1000-mac"; + reg = <0x134b0000 0x2000>; + + interrupt-parent = <&intc>; + interrupts = <55>; + interrupt-names = "macirq"; + + clocks = <&cgu X1000_CLK_MAC>; + clock-names = "stmmaceth"; + + mode-reg = <&mac_phy_ctrl>; + }; +... diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml new file mode 100644 index 000000000000..347b912a46bb --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml @@ -0,0 +1,226 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/microchip,sparx5-switch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Sparx5 Ethernet switch controller + +maintainers: + - Steen Hegelund <steen.hegelund@microchip.com> + - Lars Povlsen <lars.povlsen@microchip.com> + +description: | + The SparX-5 Enterprise Ethernet switch family provides a rich set of + Enterprise switching features such as advanced TCAM-based VLAN and + QoS processing enabling delivery of differentiated services, and + security through TCAM-based frame processing using versatile content + aware processor (VCAP). + + IPv4/IPv6 Layer 3 (L3) unicast and multicast routing is supported + with up to 18K IPv4/9K IPv6 unicast LPM entries and up to 9K IPv4/3K + IPv6 (S,G) multicast groups. + + L3 security features include source guard and reverse path + forwarding (uRPF) tasks. Additional L3 features include VRF-Lite and + IP tunnels (IP over GRE/IP). + + The SparX-5 switch family targets managed Layer 2 and Layer 3 + equipment in SMB, SME, and Enterprise where high port count + 1G/2.5G/5G/10G switching with 10G/25G aggregation links is required. + +properties: + $nodename: + pattern: "^switch@[0-9a-f]+$" + + compatible: + const: microchip,sparx5-switch + + reg: + items: + - description: cpu target + - description: devices target + - description: general control block target + + reg-names: + items: + - const: cpu + - const: devices + - const: gcb + + interrupts: + minItems: 1 + items: + - description: register based extraction + - description: frame dma based extraction + + interrupt-names: + minItems: 1 + items: + - const: xtr + - const: fdma + + resets: + items: + - description: Reset controller used for switch core reset (soft reset) + + reset-names: + items: + - const: switch + + mac-address: true + + ethernet-ports: + type: object + patternProperties: + "^port@[0-9a-f]+$": + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + reg: + description: Switch port number + + phys: + maxItems: 1 + description: + phandle of a Ethernet SerDes PHY. This defines which SerDes + instance will handle the Ethernet traffic. + + phy-mode: + description: + This specifies the interface used by the Ethernet SerDes towards + the PHY or SFP. + + microchip,bandwidth: + description: Specifies bandwidth in Mbit/s allocated to the port. + $ref: "/schemas/types.yaml#/definitions/uint32" + maximum: 25000 + + phy-handle: + description: + phandle of a Ethernet PHY. This is optional and if provided it + points to the cuPHY used by the Ethernet SerDes. + + sfp: + description: + phandle of an SFP. This is optional and used when not specifying + a cuPHY. It points to the SFP node that describes the SFP used by + the Ethernet SerDes. + + managed: true + + microchip,sd-sgpio: + description: + Index of the ports Signal Detect SGPIO in the set of 384 SGPIOs + This is optional, and only needed if the default used index is + is not correct. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 383 + + required: + - reg + - phys + - phy-mode + - microchip,bandwidth + + oneOf: + - required: + - phy-handle + - required: + - sfp + - managed + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - resets + - reset-names + - ethernet-ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + switch: switch@600000000 { + compatible = "microchip,sparx5-switch"; + reg = <0 0x401000>, + <0x10004000 0x7fc000>, + <0x11010000 0xaf0000>; + reg-names = "cpu", "devices", "gcb"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "xtr"; + resets = <&reset 0>; + reset-names = "switch"; + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + /* ... */ + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + microchip,bandwidth = <25000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + microchip,sd-sgpio = <365>; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <25000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + microchip,sd-sgpio = <369>; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <25000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + microchip,sd-sgpio = <373>; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <25000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + microchip,sd-sgpio = <377>; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + mac-address = [ 00 00 00 01 02 03 ]; + }; + }; + }; + +... +# vim: set ts=2 sw=2 sts=2 tw=80 et cc=80 ft=yaml : diff --git a/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml index 477066e2b821..081742c2b726 100644 --- a/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml +++ b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml @@ -27,6 +27,9 @@ properties: reg: maxItems: 1 + clocks: + maxItems: 1 + wake-gpios: maxItems: 1 description: @@ -80,6 +83,8 @@ examples: en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>; wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>; + + clocks = <&rpmcc 20>; }; }; # UART example on Raspberry Pi diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index 5fe6d3dceb08..ed88ba4b94df 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -44,6 +44,7 @@ description: properties: compatible: enum: + - qcom,msm8998-ipa - qcom,sc7180-ipa - qcom,sc7280-ipa - qcom,sdm845-ipa diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt deleted file mode 100644 index 709ca6d51650..000000000000 --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt +++ /dev/null @@ -1,69 +0,0 @@ -Qualcomm Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Qualcomm devices. - -Serial attached Qualcomm devices shall be a child node of the host UART -device the slave device is attached to. - -Required properties: - - compatible: should contain one of the following: - * "qcom,qca6174-bt" - * "qcom,qca9377-bt" - * "qcom,wcn3990-bt" - * "qcom,wcn3991-bt" - * "qcom,wcn3998-bt" - * "qcom,qca6390-bt" - -Optional properties for compatible string qcom,qca6174-bt: - - - enable-gpios: gpio specifier used to enable chip - - clocks: clock provided to the controller (SUSCLK_32KHZ) - - firmware-name: specify the name of nvm firmware to load - -Optional properties for compatible string qcom,qca9377-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - -Required properties for compatible string qcom,wcn399x-bt: - - - vddio-supply: VDD_IO supply regulator handle. - - vddxo-supply: VDD_XO supply regulator handle. - - vddrf-supply: VDD_RF supply regulator handle. - - vddch0-supply: VDD_CH0 supply regulator handle. - -Optional properties for compatible string qcom,wcn399x-bt: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - - firmware-name: specify the name of nvm firmware to load - - clocks: clock provided to the controller - -Examples: - -serial@7570000 { - label = "BT-UART"; - status = "okay"; - - bluetooth { - compatible = "qcom,qca6174-bt"; - - enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; - clocks = <&divclk4>; - firmware-name = "nvm_00440302.bin"; - }; -}; - -serial@898000 { - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - firmware-name = "crnv21.bin"; - clocks = <&rpmhcc RPMH_RF_CLK2>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml new file mode 100644 index 000000000000..f93c6e7a1b59 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml @@ -0,0 +1,183 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Bluetooth Chips + +maintainers: + - Balakrishna Godavarthi <bgodavar@codeaurora.org> + - Rocky Liao <rjliao@codeaurora.org> + +description: + This binding describes Qualcomm UART-attached bluetooth chips. + +properties: + compatible: + enum: + - qcom,qca6174-bt + - qcom,qca9377-bt + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + - qcom,qca6390-bt + - qcom,wcn6750-bt + + enable-gpios: + maxItems: 1 + description: gpio specifier used to enable chip + + swctrl-gpios: + maxItems: 1 + description: gpio specifier is used to find status + of clock supply to SoC + + clocks: + maxItems: 1 + description: clock provided to the controller (SUSCLK_32KHZ) + + vddio-supply: + description: VDD_IO supply regulator handle + + vddxo-supply: + description: VDD_XO supply regulator handle + + vddrf-supply: + description: VDD_RF supply regulator handle + + vddch0-supply: + description: VDD_CH0 supply regulator handle + + vddaon-supply: + description: VDD_AON supply regulator handle + + vddbtcxmx-supply: + description: VDD_BT_CXMX supply regulator handle + + vddrfacmn-supply: + description: VDD_RFA_CMN supply regulator handle + + vddrfa0p8-supply: + description: VDD_RFA_0P8 suppply regulator handle + + vddrfa1p7-supply: + description: VDD_RFA_1P7 supply regulator handle + + vddrfa1p2-supply: + description: VDD_RFA_1P2 supply regulator handle + + vddrfa2p2-supply: + description: VDD_RFA_2P2 supply regulator handle + + vddasd-supply: + description: VDD_ASD supply regulator handle + + max-speed: + description: see Documentation/devicetree/bindings/serial/serial.yaml + + firmware-name: + description: specify the name of nvm firmware to load + + local-bd-address: + description: see Documentation/devicetree/bindings/net/bluetooth.txt + + +required: + - compatible + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,qca6174-bt + then: + required: + - enable-gpios + - clocks + + - if: + properties: + compatible: + contains: + enum: + - qcom,wcn3990-bt + - qcom,wcn3991-bt + - qcom,wcn3998-bt + then: + required: + - vddio-supply + - vddxo-supply + - vddrf-supply + - vddch0-supply + + - if: + properties: + compatible: + contains: + enum: + - qcom,wcn6750-bt + then: + required: + - enable-gpios + - swctrl-gpios + - vddio-supply + - vddaon-supply + - vddbtcxmx-supply + - vddrfacmn-supply + - vddrfa0p8-supply + - vddrfa1p7-supply + - vddrfa1p2-supply + - vddasd-supply + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + serial { + + bluetooth { + compatible = "qcom,qca6174-bt"; + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; + }; + }; + - | + serial { + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + firmware-name = "crnv21.bin"; + }; + }; + - | + serial { + + bluetooth { + compatible = "qcom,wcn6750-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_default>; + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; + vddio-supply = <&vreg_l19b_1p8>; + vddaon-supply = <&vreg_s7b_0p9>; + vddbtcxmx-supply = <&vreg_s7b_0p9>; + vddrfacmn-supply = <&vreg_s7b_0p9>; + vddrfa0p8-supply = <&vreg_s7b_0p9>; + vddrfa1p7-supply = <&vreg_s1b_1p8>; + vddrfa1p2-supply = <&vreg_s8b_1p2>; + vddrfa2p2-supply = <&vreg_s1c_2p2>; + vddasd-supply = <&vreg_l11c_2p8>; + max-speed = <3200000>; + firmware-name = "msnv11.bin"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml b/Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml new file mode 100644 index 000000000000..bb94a2388520 --- /dev/null +++ b/Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/realtek,rtl82xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek RTL82xx PHY + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +description: + Bindings for Realtek RTL82xx PHYs + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + realtek,clkout-disable: + type: boolean + description: + Disable CLKOUT clock, CLKOUT clock default is enabled after hardware reset. + + + realtek,aldps-enable: + type: boolean + description: + Enable ALDPS mode, ALDPS mode default is disabled after hardware reset. + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + realtek,clkout-disable; + realtek,aldps-enable; + }; + }; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml index 5acddb6171bf..083623c8d718 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml @@ -19,10 +19,12 @@ select: - rockchip,rk3128-gmac - rockchip,rk3228-gmac - rockchip,rk3288-gmac + - rockchip,rk3308-gmac - rockchip,rk3328-gmac - rockchip,rk3366-gmac - rockchip,rk3368-gmac - rockchip,rk3399-gmac + - rockchip,rk3568-gmac - rockchip,rv1108-gmac required: - compatible @@ -32,17 +34,23 @@ allOf: properties: compatible: - items: - - enum: - - rockchip,px30-gmac - - rockchip,rk3128-gmac - - rockchip,rk3228-gmac - - rockchip,rk3288-gmac - - rockchip,rk3328-gmac - - rockchip,rk3366-gmac - - rockchip,rk3368-gmac - - rockchip,rk3399-gmac - - rockchip,rv1108-gmac + oneOf: + - items: + - enum: + - rockchip,px30-gmac + - rockchip,rk3128-gmac + - rockchip,rk3228-gmac + - rockchip,rk3288-gmac + - rockchip,rk3308-gmac + - rockchip,rk3328-gmac + - rockchip,rk3366-gmac + - rockchip,rk3368-gmac + - rockchip,rk3399-gmac + - rockchip,rv1108-gmac + - items: + - enum: + - rockchip,rk3568-gmac + - const: snps,dwmac-4.20a clocks: minItems: 5 diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml index 2edd8bea993e..56f2235f5fb5 100644 --- a/Documentation/devicetree/bindings/net/snps,dwmac.yaml +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -51,11 +51,20 @@ properties: - allwinner,sun8i-r40-emac - allwinner,sun8i-v3s-emac - allwinner,sun50i-a64-emac + - loongson,ls2k-dwmac + - loongson,ls7a-dwmac - amlogic,meson6-dwmac - amlogic,meson8b-dwmac - amlogic,meson8m2-dwmac - amlogic,meson-gxbb-dwmac - amlogic,meson-axg-dwmac + - loongson,ls2k-dwmac + - loongson,ls7a-dwmac + - ingenic,jz4775-mac + - ingenic,x1000-mac + - ingenic,x1600-mac + - ingenic,x1830-mac + - ingenic,x2000-mac - rockchip,px30-gmac - rockchip,rk3128-gmac - rockchip,rk3228-gmac @@ -310,6 +319,11 @@ allOf: - allwinner,sun8i-r40-emac - allwinner,sun8i-v3s-emac - allwinner,sun50i-a64-emac + - ingenic,jz4775-mac + - ingenic,x1000-mac + - ingenic,x1600-mac + - ingenic,x1830-mac + - ingenic,x2000-mac - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac @@ -353,6 +367,13 @@ allOf: - allwinner,sun8i-r40-emac - allwinner,sun8i-v3s-emac - allwinner,sun50i-a64-emac + - loongson,ls2k-dwmac + - loongson,ls7a-dwmac + - ingenic,jz4775-mac + - ingenic,x1000-mac + - ingenic,x1600-mac + - ingenic,x1830-mac + - ingenic,x2000-mac - snps,dwmac-4.00 - snps,dwmac-4.10a - snps,dwmac-4.20a |