diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa')
4 files changed, 242 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 47a6a7fe0b86..1811e1972a7a 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -24,6 +24,14 @@ Required properties: "brcm,bcm53018-srab" "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string + For the BCM5831X/BCM1140x SoCs with an integrated switch, must be one of: + "brcm,bcm11404-srab" + "brcm,bcm11407-srab" + "brcm,bcm11409-srab" + "brcm,bcm58310-srab" + "brcm,bcm58311-srab" + "brcm,bcm58313-srab" and the mandatory "brcm,omega-srab" string + For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of: "brcm,bcm58522-srab" "brcm,bcm58523-srab" diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 60d50a2b0323..feb007af13cb 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -30,7 +30,6 @@ Required properties: Optional properties: - reset-gpios : Should be a gpio specifier for a reset line -- interrupt-parent : Parent interrupt controller - interrupts : Interrupt from the switch - interrupt-controller : Indicates the switch is itself an interrupt controller. This is used for the PHY interrupts. diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt new file mode 100644 index 000000000000..b6ae8541bd55 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt @@ -0,0 +1,153 @@ +Realtek SMI-based Switches +========================== + +The SMI "Simple Management Interface" is a two-wire protocol using +bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does +not use the MDIO protocol. This binding defines how to specify the +SMI-based Realtek devices. + +Required properties: + +- compatible: must be exactly one of: + "realtek,rtl8366" + "realtek,rtl8366rb" (4+1 ports) + "realtek,rtl8366s" (4+1 ports) + "realtek,rtl8367" + "realtek,rtl8367b" + "realtek,rtl8368s" (8 port) + "realtek,rtl8369" + "realtek,rtl8370" (8 port) + +Required properties: +- mdc-gpios: GPIO line for the MDC clock line. +- mdio-gpios: GPIO line for the MDIO data line. +- reset-gpios: GPIO line for the reset signal. + +Optional properties: +- realtek,disable-leds: if the LED drivers are not used in the + hardware design this will disable them so they are not turned on + and wasting power. + +Required subnodes: + +- interrupt-controller + + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the SMI-based chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + +Required properties of interrupt-controller: + +- interrupt: parent interrupt, see interrupt-controller/interrupts.txt +- interrupt-controller: see interrupt-controller/interrupts.txt +- #address-cells: should be <0> +- #interrupt-cells: should be <1> + +- mdio + + This defines the internal MDIO bus of the SMI device, mostly for the + purpose of being able to hook the interrupts to the right PHY and + the right PHY to the corresponding port. + +Required properties of mdio: + +- compatible: should be set to "realtek,smi-mdio" for all SMI devices + +See net/mdio.txt for additional MDIO bus properties. + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio", "dsa-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc>; + interrupts = <0>; + }; + phy1: phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc>; + interrupts = <1>; + }; + phy2: phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc>; + interrupts = <2>; + }; + phy3: phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc>; + interrupts = <3>; + }; + phy4: phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc>; + interrupts = <12>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt new file mode 100644 index 000000000000..ed4710c40641 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -0,0 +1,81 @@ +Vitesse VSC73xx Switches +======================== + +This defines device tree bindings for the Vitesse VSC73xx switch chips. +The Vitesse company has been acquired by Microsemi and Microsemi in turn +acquired by Microchip but retains this vendor branding. + +The currently supported switch chips are: +Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch +Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch + +The device tree node is an SPI device so it must reside inside a SPI bus +device tree node, see spi/spi-bus.txt + +Required properties: + +- compatible: must be exactly one of: + "vitesse,vsc7385" + "vitesse,vsc7388" + "vitesse,vsc7395" + "vitesse,vsc7398" +- gpio-controller: indicates that this switch is also a GPIO controller, + see gpio/gpio.txt +- #gpio-cells: this must be set to <2> and indicates that we are a twocell + GPIO controller, see gpio/gpio.txt + +Optional properties: + +- reset-gpios: a handle to a GPIO line that can issue reset of the chip. + It should be tagged as active low. + +Required subnodes: + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +switch@0 { + compatible = "vitesse,vsc7395"; + reg = <0>; + /* Specified for 2.5 MHz or below */ + spi-max-frequency = <2500000>; + gpio-controller; + #gpio-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + vsc: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; +}; |