diff options
| -rw-r--r-- | drivers/mtd/devices/st_spi_fsm.c | 91 |
1 files changed, 91 insertions, 0 deletions
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c index 03b49a44970d..c902d5bc69a4 100644 --- a/drivers/mtd/devices/st_spi_fsm.c +++ b/drivers/mtd/devices/st_spi_fsm.c @@ -200,6 +200,53 @@ #define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */ +/* Flash Commands */ +#define FLASH_CMD_WREN 0x06 +#define FLASH_CMD_WRDI 0x04 +#define FLASH_CMD_RDID 0x9f +#define FLASH_CMD_RDSR 0x05 +#define FLASH_CMD_RDSR2 0x35 +#define FLASH_CMD_WRSR 0x01 +#define FLASH_CMD_SE_4K 0x20 +#define FLASH_CMD_SE_32K 0x52 +#define FLASH_CMD_SE 0xd8 +#define FLASH_CMD_CHIPERASE 0xc7 +#define FLASH_CMD_WRVCR 0x81 +#define FLASH_CMD_RDVCR 0x85 + +#define FLASH_CMD_READ 0x03 /* READ */ +#define FLASH_CMD_READ_FAST 0x0b /* FAST READ */ +#define FLASH_CMD_READ_1_1_2 0x3b /* DUAL OUTPUT READ */ +#define FLASH_CMD_READ_1_2_2 0xbb /* DUAL I/O READ */ +#define FLASH_CMD_READ_1_1_4 0x6b /* QUAD OUTPUT READ */ +#define FLASH_CMD_READ_1_4_4 0xeb /* QUAD I/O READ */ + +#define FLASH_CMD_WRITE 0x02 /* PAGE PROGRAM */ +#define FLASH_CMD_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */ +#define FLASH_CMD_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */ +#define FLASH_CMD_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */ +#define FLASH_CMD_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */ + +#define FLASH_CMD_EN4B_ADDR 0xb7 /* Enter 4-byte address mode */ +#define FLASH_CMD_EX4B_ADDR 0xe9 /* Exit 4-byte address mode */ + +/* READ commands with 32-bit addressing (N25Q256 and S25FLxxxS) */ +#define FLASH_CMD_READ4 0x13 +#define FLASH_CMD_READ4_FAST 0x0c +#define FLASH_CMD_READ4_1_1_2 0x3c +#define FLASH_CMD_READ4_1_2_2 0xbc +#define FLASH_CMD_READ4_1_1_4 0x6c +#define FLASH_CMD_READ4_1_4_4 0xec + +/* + * Flags to tweak operation of default read/write/erase routines + */ +#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001 +#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002 +#define CFG_WRITE_EX_32BIT_ADDR_DELAY 0x00000004 +#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008 +#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010 + struct stfsm { struct device *dev; void __iomem *base; @@ -208,6 +255,7 @@ struct stfsm { struct mutex lock; struct flash_info *info; + uint32_t configuration; uint32_t fifo_dir_delay; bool booted_from_spi; bool reset_signal; @@ -402,6 +450,49 @@ static struct seq_rw_config default_write_configs[] = { {0x00, 0, 0, 0, 0, 0x00, 0, 0}, }; +/* + * [N25Qxxx] Configuration + */ +#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4) +#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3) +#define N25Q_VCR_WRAP_CONT 0x3 + +/* N25Q 3-byte Address READ configurations + * - 'FAST' variants configured for 8 dummy cycles. + * + * Note, the number of dummy cycles used for 'FAST' READ operations is + * configurable and would normally be tuned according to the READ command and + * operating frequency. However, this applies universally to all 'FAST' READ + * commands, including those used by the SPIBoot controller, and remains in + * force until the device is power-cycled. Since the SPIBoot controller is + * hard-wired to use 8 dummy cycles, we must configure the device to also use 8 + * cycles. + */ +static struct seq_rw_config n25q_read3_configs[] = { + {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, FLASH_CMD_READ_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* N25Q 4-byte Address READ configurations + * - use special 4-byte address READ commands (reduces overheads, and + * reduces risk of hitting watchdog reset issues). + * - 'FAST' variants configured for 8 dummy cycles (see note above.) + */ +static struct seq_rw_config n25q_read4_configs[] = { + {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, FLASH_CMD_READ4_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ4, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */ static struct stfsm_seq stfsm_seq_read_jedec = { |