Merge tag 'v5.4.57' into dev-5.4dev-5.4

This is the 5.4.57 stable release

Signed-off-by: Joel Stanley <joel@jms.id.au>

3 files changed, 30 insertions, 2 deletions

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index f1d230c5a8ef..2675771a03a0 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -524,6 +524,7 @@ static void __init serial8250_isa_init_ports(void)
 		 */
 		up->mcr_mask = ~ALPHA_KLUDGE_MCR;
 		up->mcr_force = ALPHA_KLUDGE_MCR;
+		serial8250_set_defaults(up);
 	}
 
 	/* chain base port ops to support Remote Supervisor Adapter */
@@ -547,7 +548,6 @@ static void __init serial8250_isa_init_ports(void)
 		port->membase  = old_serial_port[i].iomem_base;
 		port->iotype   = old_serial_port[i].io_type;
 		port->regshift = old_serial_port[i].iomem_reg_shift;
-		serial8250_set_defaults(up);
 
 		port->irqflags |= irqflag;
 		if (serial8250_isa_config != NULL)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index e1268646ee56..9e2dbe43667a 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -307,7 +307,17 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p)
 	 * devices will export them as GPIOs, so we pre-configure them safely
 	 * as inputs.
 	 */
-	u8 dir = pcidev->vendor == PCI_VENDOR_ID_EXAR ? 0xff : 0x00;
+
+	u8 dir = 0x00;
+
+	if  ((pcidev->vendor == PCI_VENDOR_ID_EXAR) &&
+		(pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) {
+		// Configure GPIO as inputs for Commtech adapters
+		dir = 0xff;
+	} else {
+		// Configure GPIO as outputs for SeaLevel adapters
+		dir = 0x00;
+	}
 
 	writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
 	writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index 4d067f515f74..2b59a4305077 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -305,8 +305,21 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 	}
 #endif
 
+	/*
+	 * Store the requested baud rate before calling the generic 8250
+	 * set_termios method. Standard 8250 port expects bauds to be
+	 * no higher than (uartclk / 16) so the baud will be clamped if it
+	 * gets out of that bound. Mediatek 8250 port supports speed
+	 * higher than that, therefore we'll get original baud rate back
+	 * after calling the generic set_termios method and recalculate
+	 * the speed later in this method.
+	 */
+	baud = tty_termios_baud_rate(termios);
+
 	serial8250_do_set_termios(port, termios, old);
 
+	tty_termios_encode_baud_rate(termios, baud, baud);
+
 	/*
 	 * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS)
 	 *
@@ -338,6 +351,11 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 	 */
 	spin_lock_irqsave(&port->lock, flags);
 
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
 	/* set DLAB we have cval saved in up->lcr from the call to the core */
 	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
 	serial_dl_write(up, quot);