Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing

Kishon writes:

Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.

28 files changed, 1936 insertions, 118 deletions

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 2a436e607f99..ccad8809ecb1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -15,6 +15,13 @@ config GENERIC_PHY
 	  phy users can obtain reference to the PHY. All the users of this
 	  framework should select this config.
 
+config PHY_BERLIN_USB
+	tristate "Marvell Berlin USB PHY Driver"
+	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the USB PHY on Marvell Berlin SoCs.
+
 config PHY_BERLIN_SATA
 	tristate "Marvell Berlin SATA PHY driver"
 	depends on ARCH_BERLIN && HAS_IOMEM && OF
@@ -22,6 +29,12 @@ config PHY_BERLIN_SATA
 	help
 	  Enable this to support the SATA PHY on Marvell Berlin SoCs.
 
+config ARMADA375_USBCLUSTER_PHY
+	def_bool y
+	depends on MACH_ARMADA_375 || COMPILE_TEST
+	depends on OF
+	select GENERIC_PHY
+
 config PHY_EXYNOS_MIPI_VIDEO
 	tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
 	depends on HAS_IOMEM
@@ -38,6 +51,14 @@ config PHY_MVEBU_SATA
 	depends on OF
 	select GENERIC_PHY
 
+config PHY_MIPHY28LP
+	tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407"
+	depends on ARCH_STI
+	select GENERIC_PHY
+	help
+	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
+	  that is part of STMicroelectronics STiH407 SoC.
+
 config PHY_MIPHY365X
 	tristate "STMicroelectronics MIPHY365X PHY driver for STiH41x series"
 	depends on ARCH_STI
@@ -193,7 +214,7 @@ config PHY_EXYNOS5250_USB2
 
 config PHY_EXYNOS5_USBDRD
 	tristate "Exynos5 SoC series USB DRD PHY driver"
-	depends on ARCH_EXYNOS5 && OF
+	depends on ARCH_EXYNOS && OF
 	depends on HAS_IOMEM
 	depends on USB_DWC3_EXYNOS
 	select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c4590fce082f..aa74f961e44e 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -3,11 +3,14 @@
 #
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
+obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
+obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
 obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
 obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
+obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
 obj-$(CONFIG_PHY_MIPHY365X)		+= phy-miphy365x.o
 obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
 obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
diff --git a/drivers/phy/phy-armada375-usb2.c b/drivers/phy/phy-armada375-usb2.c
new file mode 100644
index 000000000000..ac7d99d01cb3
--- /dev/null
+++ b/drivers/phy/phy-armada375-usb2.c
@@ -0,0 +1,158 @@
+/*
+ * USB cluster support for Armada 375 platform.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2 or later. This program is licensed "as is"
+ * without any warranty of any kind, whether express or implied.
+ *
+ * Armada 375 comes with an USB2 host and device controller and an
+ * USB3 controller. The USB cluster control register allows to manage
+ * common features of both USB controllers.
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define USB2_PHY_CONFIG_DISABLE BIT(0)
+
+struct armada375_cluster_phy {
+	struct phy *phy;
+	void __iomem *reg;
+	bool use_usb3;
+	int phy_provided;
+};
+
+static int armada375_usb_phy_init(struct phy *phy)
+{
+	struct armada375_cluster_phy *cluster_phy;
+	u32 reg;
+
+	cluster_phy = dev_get_drvdata(phy->dev.parent);
+	if (!cluster_phy)
+		return -ENODEV;
+
+	reg = readl(cluster_phy->reg);
+	if (cluster_phy->use_usb3)
+		reg |= USB2_PHY_CONFIG_DISABLE;
+	else
+		reg &= ~USB2_PHY_CONFIG_DISABLE;
+	writel(reg, cluster_phy->reg);
+
+	return 0;
+}
+
+static struct phy_ops armada375_usb_phy_ops = {
+	.init = armada375_usb_phy_init,
+	.owner = THIS_MODULE,
+};
+
+/*
+ * Only one controller can use this PHY. We shouldn't have the case
+ * when two controllers want to use this PHY. But if this case occurs
+ * then we provide a phy to the first one and return an error for the
+ * next one. This error has also to be an error returned by
+ * devm_phy_optional_get() so different from ENODEV for USB2. In the
+ * USB3 case it still optional and we use ENODEV.
+ */
+static struct phy *armada375_usb_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct armada375_cluster_phy *cluster_phy = dev_get_drvdata(dev);
+
+	if (!cluster_phy)
+		return  ERR_PTR(-ENODEV);
+
+	/*
+	 * Either the phy had never been requested and then the first
+	 * usb claiming it can get it, or it had already been
+	 * requested in this case, we only allow to use it with the
+	 * same configuration.
+	 */
+	if (WARN_ON((cluster_phy->phy_provided != PHY_NONE) &&
+			(cluster_phy->phy_provided != args->args[0]))) {
+		dev_err(dev, "This PHY has already been provided!\n");
+		dev_err(dev, "Check your device tree, only one controller can use it\n.");
+		if (args->args[0] == PHY_TYPE_USB2)
+			return ERR_PTR(-EBUSY);
+		else
+			return ERR_PTR(-ENODEV);
+	}
+
+	if (args->args[0] == PHY_TYPE_USB2)
+		cluster_phy->use_usb3 = false;
+	else if (args->args[0] == PHY_TYPE_USB3)
+		cluster_phy->use_usb3 = true;
+	else {
+		dev_err(dev, "Invalid PHY mode\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	/* Store which phy mode is used for next test */
+	cluster_phy->phy_provided = args->args[0];
+
+	return cluster_phy->phy;
+}
+
+static int armada375_usb_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy *phy;
+	struct phy_provider *phy_provider;
+	void __iomem *usb_cluster_base;
+	struct resource *res;
+	struct armada375_cluster_phy *cluster_phy;
+
+	cluster_phy = devm_kzalloc(dev, sizeof(*cluster_phy), GFP_KERNEL);
+	if (!cluster_phy)
+		return  -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	usb_cluster_base = devm_ioremap_resource(&pdev->dev, res);
+	if (!usb_cluster_base)
+		return -ENOMEM;
+
+	phy = devm_phy_create(dev, NULL, &armada375_usb_phy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	cluster_phy->phy = phy;
+	cluster_phy->reg = usb_cluster_base;
+
+	dev_set_drvdata(dev, cluster_phy);
+
+	phy_provider = devm_of_phy_provider_register(&pdev->dev,
+						     armada375_usb_phy_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id of_usb_cluster_table[] = {
+	{ .compatible = "marvell,armada-375-usb-cluster", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, of_usb_cluster_table);
+
+static struct platform_driver armada375_usb_phy_driver = {
+	.probe	= armada375_usb_phy_probe,
+	.driver = {
+		.of_match_table	= of_usb_cluster_table,
+		.name  = "armada-375-usb-cluster",
+		.owner = THIS_MODULE,
+	}
+};
+module_platform_driver(armada375_usb_phy_driver);
+
+MODULE_DESCRIPTION("Armada 375 USB cluster driver");
+MODULE_AUTHOR("Gregory CLEMENT <gregory.clement@free-electrons.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/phy-bcm-kona-usb2.c b/drivers/phy/phy-bcm-kona-usb2.c
index c1e0ca335c0e..ef2dc1aab2b9 100644
--- a/drivers/phy/phy-bcm-kona-usb2.c
+++ b/drivers/phy/phy-bcm-kona-usb2.c
@@ -117,7 +117,7 @@ static int bcm_kona_usb2_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, phy);
 
-	gphy = devm_phy_create(dev, NULL, &ops, NULL);
+	gphy = devm_phy_create(dev, NULL, &ops);
 	if (IS_ERR(gphy))
 		return PTR_ERR(gphy);
 
diff --git a/drivers/phy/phy-berlin-sata.c b/drivers/phy/phy-berlin-sata.c
index 69ced52d72aa..099eee8851e5 100644
--- a/drivers/phy/phy-berlin-sata.c
+++ b/drivers/phy/phy-berlin-sata.c
@@ -30,7 +30,8 @@
 #define MBUS_WRITE_REQUEST_SIZE_128	(BIT(2) << 16)
 #define MBUS_READ_REQUEST_SIZE_128	(BIT(2) << 19)
 
-#define PHY_BASE		0x200
+#define BG2_PHY_BASE		0x080
+#define BG2Q_PHY_BASE		0x200
 
 /* register 0x01 */
 #define REF_FREF_SEL_25		BIT(0)
@@ -61,15 +62,16 @@ struct phy_berlin_priv {
 	struct clk		*clk;
 	struct phy_berlin_desc	**phys;
 	unsigned		nphys;
+	u32			phy_base;
 };
 
-static inline void phy_berlin_sata_reg_setbits(void __iomem *ctrl_reg, u32 reg,
-					       u32 mask, u32 val)
+static inline void phy_berlin_sata_reg_setbits(void __iomem *ctrl_reg,
+			       u32 phy_base, u32 reg, u32 mask, u32 val)
 {
 	u32 regval;
 
 	/* select register */
-	writel(PHY_BASE + reg, ctrl_reg + PORT_VSR_ADDR);
+	writel(phy_base + reg, ctrl_reg + PORT_VSR_ADDR);
 
 	/* set bits */
 	regval = readl(ctrl_reg + PORT_VSR_DATA);
@@ -103,17 +105,20 @@ static int phy_berlin_sata_power_on(struct phy *phy)
 	writel(regval, priv->base + HOST_VSA_DATA);
 
 	/* set PHY mode and ref freq to 25 MHz */
-	phy_berlin_sata_reg_setbits(ctrl_reg, 0x1, 0xff,
-				    REF_FREF_SEL_25 | PHY_MODE_SATA);
+	phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x01,
+				    0x00ff, REF_FREF_SEL_25 | PHY_MODE_SATA);
 
 	/* set PHY up to 6 Gbps */
-	phy_berlin_sata_reg_setbits(ctrl_reg, 0x25, 0xc00, PHY_GEN_MAX_6_0);
+	phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x25,
+				    0x0c00, PHY_GEN_MAX_6_0);
 
 	/* set 40 bits width */
-	phy_berlin_sata_reg_setbits(ctrl_reg, 0x23,  0xc00, DATA_BIT_WIDTH_40);
+	phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x23,
+				    0x0c00, DATA_BIT_WIDTH_40);
 
 	/* use max pll rate */
-	phy_berlin_sata_reg_setbits(ctrl_reg, 0x2, 0x0, USE_MAX_PLL_RATE);
+	phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x02,
+				    0x0000, USE_MAX_PLL_RATE);
 
 	/* set Gen3 controller speed */
 	regval = readl(ctrl_reg + PORT_SCR_CTL);
@@ -218,6 +223,11 @@ static int phy_berlin_sata_probe(struct platform_device *pdev)
 	if (!priv->phys)
 		return -ENOMEM;
 
+	if (of_device_is_compatible(dev->of_node, "marvell,berlin2-sata-phy"))
+		priv->phy_base = BG2_PHY_BASE;
+	else
+		priv->phy_base = BG2Q_PHY_BASE;
+
 	dev_set_drvdata(dev, priv);
 	spin_lock_init(&priv->lock);
 
@@ -239,7 +249,7 @@ static int phy_berlin_sata_probe(struct platform_device *pdev)
 		if (!phy_desc)
 			return -ENOMEM;
 
-		phy = devm_phy_create(dev, NULL, &phy_berlin_sata_ops, NULL);
+		phy = devm_phy_create(dev, NULL, &phy_berlin_sata_ops);
 		if (IS_ERR(phy)) {
 			dev_err(dev, "failed to create PHY %d\n", phy_id);
 			return PTR_ERR(phy);
@@ -258,13 +268,11 @@ static int phy_berlin_sata_probe(struct platform_device *pdev)
 
 	phy_provider =
 		devm_of_phy_provider_register(dev, phy_berlin_sata_phy_xlate);
-	if (IS_ERR(phy_provider))
-		return PTR_ERR(phy_provider);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
 static const struct of_device_id phy_berlin_sata_of_match[] = {
+	{ .compatible = "marvell,berlin2-sata-phy" },
 	{ .compatible = "marvell,berlin2q-sata-phy" },
 	{ },
 };
diff --git a/drivers/phy/phy-berlin-usb.c b/drivers/phy/phy-berlin-usb.c
new file mode 100644
index 000000000000..c8a8d53a6ece
--- /dev/null
+++ b/drivers/phy/phy-berlin-usb.c
@@ -0,0 +1,223 @@
+/*
+ * Copyright (C) 2014 Marvell Technology Group Ltd.
+ *
+ * Antoine Tenart <antoine.tenart@free-electrons.com>
+ * Jisheng Zhang <jszhang@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+#define USB_PHY_PLL		0x04
+#define USB_PHY_PLL_CONTROL	0x08
+#define USB_PHY_TX_CTRL0	0x10
+#define USB_PHY_TX_CTRL1	0x14
+#define USB_PHY_TX_CTRL2	0x18
+#define USB_PHY_RX_CTRL		0x20
+#define USB_PHY_ANALOG		0x34
+
+/* USB_PHY_PLL */
+#define CLK_REF_DIV(x)		((x) << 4)
+#define FEEDBACK_CLK_DIV(x)	((x) << 8)
+
+/* USB_PHY_PLL_CONTROL */
+#define CLK_STABLE		BIT(0)
+#define PLL_CTRL_PIN		BIT(1)
+#define PLL_CTRL_REG		BIT(2)
+#define PLL_ON			BIT(3)
+#define PHASE_OFF_TOL_125	(0x0 << 5)
+#define PHASE_OFF_TOL_250	BIT(5)
+#define KVC0_CALIB		(0x0 << 9)
+#define KVC0_REG_CTRL		BIT(9)
+#define KVC0_HIGH		(0x0 << 10)
+#define KVC0_LOW		(0x3 << 10)
+#define CLK_BLK_EN		BIT(13)
+
+/* USB_PHY_TX_CTRL0 */
+#define EXT_HS_RCAL_EN		BIT(3)
+#define EXT_FS_RCAL_EN		BIT(4)
+#define IMPCAL_VTH_DIV(x)	((x) << 5)
+#define EXT_RS_RCAL_DIV(x)	((x) << 8)
+#define EXT_FS_RCAL_DIV(x)	((x) << 12)
+
+/* USB_PHY_TX_CTRL1 */
+#define TX_VDD15_14		(0x0 << 4)
+#define TX_VDD15_15		BIT(4)
+#define TX_VDD15_16		(0x2 << 4)
+#define TX_VDD15_17		(0x3 << 4)
+#define TX_VDD12_VDD		(0x0 << 6)
+#define TX_VDD12_11		BIT(6)
+#define TX_VDD12_12		(0x2 << 6)
+#define TX_VDD12_13		(0x3 << 6)
+#define LOW_VDD_EN		BIT(8)
+#define TX_OUT_AMP(x)		((x) << 9)
+
+/* USB_PHY_TX_CTRL2 */
+#define TX_CHAN_CTRL_REG(x)	((x) << 0)
+#define DRV_SLEWRATE(x)		((x) << 4)
+#define IMP_CAL_FS_HS_DLY_0	(0x0 << 6)
+#define IMP_CAL_FS_HS_DLY_1	BIT(6)
+#define IMP_CAL_FS_HS_DLY_2	(0x2 << 6)
+#define IMP_CAL_FS_HS_DLY_3	(0x3 << 6)
+#define FS_DRV_EN_MASK(x)	((x) << 8)
+#define HS_DRV_EN_MASK(x)	((x) << 12)
+
+/* USB_PHY_RX_CTRL */
+#define PHASE_FREEZE_DLY_2_CL	(0x0 << 0)
+#define PHASE_FREEZE_DLY_4_CL	BIT(0)
+#define ACK_LENGTH_8_CL		(0x0 << 2)
+#define ACK_LENGTH_12_CL	BIT(2)
+#define ACK_LENGTH_16_CL	(0x2 << 2)
+#define ACK_LENGTH_20_CL	(0x3 << 2)
+#define SQ_LENGTH_3		(0x0 << 4)
+#define SQ_LENGTH_6		BIT(4)
+#define SQ_LENGTH_9		(0x2 << 4)
+#define SQ_LENGTH_12		(0x3 << 4)
+#define DISCON_THRESHOLD_260	(0x0 << 6)
+#define DISCON_THRESHOLD_270	BIT(6)
+#define DISCON_THRESHOLD_280	(0x2 << 6)
+#define DISCON_THRESHOLD_290	(0x3 << 6)
+#define SQ_THRESHOLD(x)		((x) << 8)
+#define LPF_COEF(x)		((x) << 12)
+#define INTPL_CUR_10		(0x0 << 14)
+#define INTPL_CUR_20		BIT(14)
+#define INTPL_CUR_30		(0x2 << 14)
+#define INTPL_CUR_40		(0x3 << 14)
+
+/* USB_PHY_ANALOG */
+#define ANA_PWR_UP		BIT(1)
+#define ANA_PWR_DOWN		BIT(2)
+#define V2I_VCO_RATIO(x)	((x) << 7)
+#define R_ROTATE_90		(0x0 << 10)
+#define R_ROTATE_0		BIT(10)
+#define MODE_TEST_EN		BIT(11)
+#define ANA_TEST_DC_CTRL(x)	((x) << 12)
+
+#define to_phy_berlin_usb_priv(p)	\
+	container_of((p), struct phy_berlin_usb_priv, phy)
+
+static const u32 phy_berlin_pll_dividers[] = {
+	/* Berlin 2 */
+	CLK_REF_DIV(0xc) | FEEDBACK_CLK_DIV(0x54),
+	/* Berlin 2CD */
+	CLK_REF_DIV(0x6) | FEEDBACK_CLK_DIV(0x55),
+};
+
+struct phy_berlin_usb_priv {
+	void __iomem		*base;
+	struct phy		*phy;
+	struct reset_control	*rst_ctrl;
+	u32			pll_divider;
+};
+
+static int phy_berlin_usb_power_on(struct phy *phy)
+{
+	struct phy_berlin_usb_priv *priv = dev_get_drvdata(phy->dev.parent);
+
+	reset_control_reset(priv->rst_ctrl);
+
+	writel(priv->pll_divider,
+	       priv->base + USB_PHY_PLL);
+	writel(CLK_STABLE | PLL_CTRL_REG | PHASE_OFF_TOL_250 | KVC0_REG_CTRL |
+	       CLK_BLK_EN, priv->base + USB_PHY_PLL_CONTROL);
+	writel(V2I_VCO_RATIO(0x5) | R_ROTATE_0 | ANA_TEST_DC_CTRL(0x5),
+	       priv->base + USB_PHY_ANALOG);
+	writel(PHASE_FREEZE_DLY_4_CL | ACK_LENGTH_16_CL | SQ_LENGTH_12 |
+	       DISCON_THRESHOLD_260 | SQ_THRESHOLD(0xa) | LPF_COEF(0x2) |
+	       INTPL_CUR_30, priv->base + USB_PHY_RX_CTRL);
+
+	writel(TX_VDD12_13 | TX_OUT_AMP(0x3), priv->base + USB_PHY_TX_CTRL1);
+	writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
+	       priv->base + USB_PHY_TX_CTRL0);
+
+	writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4) |
+	       EXT_FS_RCAL_DIV(0x2), priv->base + USB_PHY_TX_CTRL0);
+
+	writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
+	       priv->base + USB_PHY_TX_CTRL0);
+	writel(TX_CHAN_CTRL_REG(0xf) | DRV_SLEWRATE(0x3) | IMP_CAL_FS_HS_DLY_3 |
+	       FS_DRV_EN_MASK(0xd), priv->base + USB_PHY_TX_CTRL2);
+
+	return 0;
+}
+
+static struct phy_ops phy_berlin_usb_ops = {
+	.power_on	= phy_berlin_usb_power_on,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id phy_berlin_sata_of_match[] = {
+	{
+		.compatible = "marvell,berlin2-usb-phy",
+		.data = &phy_berlin_pll_dividers[0],
+	},
+	{
+		.compatible = "marvell,berlin2cd-usb-phy",
+		.data = &phy_berlin_pll_dividers[1],
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_berlin_sata_of_match);
+
+static int phy_berlin_usb_probe(struct platform_device *pdev)
+{
+	const struct of_device_id *match =
+		of_match_device(phy_berlin_sata_of_match, &pdev->dev);
+	struct phy_berlin_usb_priv *priv;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->rst_ctrl = devm_reset_control_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->rst_ctrl))
+		return PTR_ERR(priv->rst_ctrl);
+
+	priv->pll_divider = *((u32 *)match->data);
+
+	priv->phy = devm_phy_create(&pdev->dev, NULL, &phy_berlin_usb_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(&pdev->dev, "failed to create PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return PTR_ERR(phy_provider);
+
+	return 0;
+}
+
+static struct platform_driver phy_berlin_usb_driver = {
+	.probe	= phy_berlin_usb_probe,
+	.driver	= {
+		.name		= "phy-berlin-usb",
+		.owner		= THIS_MODULE,
+		.of_match_table	= phy_berlin_sata_of_match,
+	 },
+};
+module_platform_driver(phy_berlin_usb_driver);
+
+MODULE_AUTHOR("Antoine Tenart <antoine.tenart@free-electrons.com>");
+MODULE_DESCRIPTION("Marvell Berlin PHY driver for USB");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index ff5eec5af817..a12d35338313 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -26,6 +26,7 @@
 static struct class *phy_class;
 static DEFINE_MUTEX(phy_provider_mutex);
 static LIST_HEAD(phy_provider_list);
+static LIST_HEAD(phys);
 static DEFINE_IDA(phy_ida);
 
 static void devm_phy_release(struct device *dev, void *res)
@@ -54,34 +55,79 @@ static int devm_phy_match(struct device *dev, void *res, void *match_data)
 	return res == match_data;
 }
 
-static struct phy *phy_lookup(struct device *device, const char *port)
+/**
+ * phy_create_lookup() - allocate and register PHY/device association
+ * @phy: the phy of the association
+ * @con_id: connection ID string on device
+ * @dev_id: the device of the association
+ *
+ * Creates and registers phy_lookup entry.
+ */
+int phy_create_lookup(struct phy *phy, const char *con_id, const char *dev_id)
 {
-	unsigned int count;
-	struct phy *phy;
-	struct device *dev;
-	struct phy_consumer *consumers;
-	struct class_dev_iter iter;
+	struct phy_lookup *pl;
 
-	class_dev_iter_init(&iter, phy_class, NULL, NULL);
-	while ((dev = class_dev_iter_next(&iter))) {
-		phy = to_phy(dev);
+	if (!phy || !dev_id || !con_id)
+		return -EINVAL;
 
-		if (!phy->init_data)
-			continue;
-		count = phy->init_data->num_consumers;
-		consumers = phy->init_data->consumers;
-		while (count--) {
-			if (!strcmp(consumers->dev_name, dev_name(device)) &&
-					!strcmp(consumers->port, port)) {
-				class_dev_iter_exit(&iter);
-				return phy;
-			}
-			consumers++;
+	pl = kzalloc(sizeof(*pl), GFP_KERNEL);
+	if (!pl)
+		return -ENOMEM;
+
+	pl->dev_id = dev_id;
+	pl->con_id = con_id;
+	pl->phy = phy;
+
+	mutex_lock(&phy_provider_mutex);
+	list_add_tail(&pl->node, &phys);
+	mutex_unlock(&phy_provider_mutex);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(phy_create_lookup);
+
+/**
+ * phy_remove_lookup() - find and remove PHY/device association
+ * @phy: the phy of the association
+ * @con_id: connection ID string on device
+ * @dev_id: the device of the association
+ *
+ * Finds and unregisters phy_lookup entry that was created with
+ * phy_create_lookup().
+ */
+void phy_remove_lookup(struct phy *phy, const char *con_id, const char *dev_id)
+{
+	struct phy_lookup *pl;
+
+	if (!phy || !dev_id || !con_id)
+		return;
+
+	mutex_lock(&phy_provider_mutex);
+	list_for_each_entry(pl, &phys, node)
+		if (pl->phy == phy && !strcmp(pl->dev_id, dev_id) &&
+		    !strcmp(pl->con_id, con_id)) {
+			list_del(&pl->node);
+			kfree(pl);
+			break;
 		}
-	}
+	mutex_unlock(&phy_provider_mutex);
+}
+EXPORT_SYMBOL_GPL(phy_remove_lookup);
 
-	class_dev_iter_exit(&iter);
-	return ERR_PTR(-ENODEV);
+static struct phy *phy_find(struct device *dev, const char *con_id)
+{
+	const char *dev_id = dev_name(dev);
+	struct phy_lookup *p, *pl = NULL;
+
+	mutex_lock(&phy_provider_mutex);
+	list_for_each_entry(p, &phys, node)
+		if (!strcmp(p->dev_id, dev_id) && !strcmp(p->con_id, con_id)) {
+			pl = p;
+			break;
+		}
+	mutex_unlock(&phy_provider_mutex);
+
+	return pl ? pl->phy : ERR_PTR(-ENODEV);
 }
 
 static struct phy_provider *of_phy_provider_lookup(struct device_node *node)
@@ -414,21 +460,13 @@ struct phy *of_phy_simple_xlate(struct device *dev, struct of_phandle_args
 {
 	struct phy *phy;
 	struct class_dev_iter iter;
-	struct device_node *node = dev->of_node;
-	struct device_node *child;
 
 	class_dev_iter_init(&iter, phy_class, NULL, NULL);
 	while ((dev = class_dev_iter_next(&iter))) {
 		phy = to_phy(dev);
-		if (node != phy->dev.of_node) {
-			for_each_child_of_node(node, child) {
-				if (child == phy->dev.of_node)
-					goto phy_found;
-			}
+		if (args->np != phy->dev.of_node)
 			continue;
-		}
 
-phy_found:
 		class_dev_iter_exit(&iter);
 		return phy;
 	}
@@ -463,7 +501,7 @@ struct phy *phy_get(struct device *dev, const char *string)
 			string);
 		phy = _of_phy_get(dev->of_node, index);
 	} else {
-		phy = phy_lookup(dev, string);
+		phy = phy_find(dev, string);
 	}
 	if (IS_ERR(phy))
 		return phy;
@@ -588,13 +626,11 @@ EXPORT_SYMBOL_GPL(devm_of_phy_get);
  * @dev: device that is creating the new phy
  * @node: device node of the phy
  * @ops: function pointers for performing phy operations
- * @init_data: contains the list of PHY consumers or NULL
  *
  * Called to create a phy using phy framework.
  */
 struct phy *phy_create(struct device *dev, struct device_node *node,
-		       const struct phy_ops *ops,
-		       struct phy_init_data *init_data)
+		       const struct phy_ops *ops)
 {
 	int ret;
 	int id;
@@ -632,7 +668,6 @@ struct phy *phy_create(struct device *dev, struct device_node *node,
 	phy->dev.of_node = node ?: dev->of_node;
 	phy->id = id;
 	phy->ops = ops;
-	phy->init_data = init_data;
 
 	ret = dev_set_name(&phy->dev, "phy-%s.%d", dev_name(dev), id);
 	if (ret)
@@ -667,7 +702,6 @@ EXPORT_SYMBOL_GPL(phy_create);
  * @dev: device that is creating the new phy
  * @node: device node of the phy
  * @ops: function pointers for performing phy operations
- * @init_data: contains the list of PHY consumers or NULL
  *
  * Creates a new PHY device adding it to the PHY class.
  * While at that, it also associates the device with the phy using devres.
@@ -675,8 +709,7 @@ EXPORT_SYMBOL_GPL(phy_create);
  * then, devres data is freed.
  */
 struct phy *devm_phy_create(struct device *dev, struct device_node *node,
-			    const struct phy_ops *ops,
-			    struct phy_init_data *init_data)
+			    const struct phy_ops *ops)
 {
 	struct phy **ptr, *phy;
 
@@ -684,7 +717,7 @@ struct phy *devm_phy_create(struct device *dev, struct device_node *node,
 	if (!ptr)
 		return ERR_PTR(-ENOMEM);
 
-	phy = phy_create(dev, node, ops, init_data);
+	phy = phy_create(dev, node, ops);
 	if (!IS_ERR(phy)) {
 		*ptr = phy;
 		devres_add(dev, ptr);
diff --git a/drivers/phy/phy-exynos-dp-video.c b/drivers/phy/phy-exynos-dp-video.c
index 84f49e5a3f24..f86cbe68ddaf 100644
--- a/drivers/phy/phy-exynos-dp-video.c
+++ b/drivers/phy/phy-exynos-dp-video.c
@@ -112,7 +112,7 @@ static int exynos_dp_video_phy_probe(struct platform_device *pdev)
 	match = of_match_node(exynos_dp_video_phy_of_match, dev->of_node);
 	state->drvdata = match->data;
 
-	phy = devm_phy_create(dev, NULL, &exynos_dp_video_phy_ops, NULL);
+	phy = devm_phy_create(dev, NULL, &exynos_dp_video_phy_ops);
 	if (IS_ERR(phy)) {
 		dev_err(dev, "failed to create Display Port PHY\n");
 		return PTR_ERR(phy);
diff --git a/drivers/phy/phy-exynos-mipi-video.c b/drivers/phy/phy-exynos-mipi-video.c
index 6a9bef138617..943e0f88a120 100644
--- a/drivers/phy/phy-exynos-mipi-video.c
+++ b/drivers/phy/phy-exynos-mipi-video.c
@@ -137,7 +137,7 @@ static int exynos_mipi_video_phy_probe(struct platform_device *pdev)
 
 	for (i = 0; i < EXYNOS_MIPI_PHYS_NUM; i++) {
 		struct phy *phy = devm_phy_create(dev, NULL,
-					&exynos_mipi_video_phy_ops, NULL);
+						  &exynos_mipi_video_phy_ops);
 		if (IS_ERR(phy)) {
 			dev_err(dev, "failed to create PHY %d\n", i);
 			return PTR_ERR(phy);
diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/phy-exynos5-usbdrd.c
index f756aca871db..04374018425f 100644
--- a/drivers/phy/phy-exynos5-usbdrd.c
+++ b/drivers/phy/phy-exynos5-usbdrd.c
@@ -141,6 +141,7 @@ struct exynos5_usbdrd_phy_drvdata {
 	const struct exynos5_usbdrd_phy_config *phy_cfg;
 	u32 pmu_offset_usbdrd0_phy;
 	u32 pmu_offset_usbdrd1_phy;
+	bool has_common_clk_gate;
 };
 
 /**
@@ -148,6 +149,9 @@ struct exynos5_usbdrd_phy_drvdata {
  * @dev: pointer to device instance of this platform device
  * @reg_phy: usb phy controller register memory base
  * @clk: phy clock for register access
+ * @pipeclk: clock for pipe3 phy
+ * @utmiclk: clock for utmi+ phy
+ * @itpclk: clock for ITP generation
  * @drv_data: pointer to SoC level driver data structure
  * @phys[]: array for 'EXYNOS5_DRDPHYS_NUM' number of PHY
  *	    instances each with its 'phy' and 'phy_cfg'.
@@ -155,12 +159,16 @@ struct exynos5_usbdrd_phy_drvdata {
  *	       reference clocks' for SS and HS operations
  * @ref_clk: reference clock to PHY block from which PHY's
  *	     operational clocks are derived
- * @ref_rate: rate of above reference clock
+ * vbus: VBUS regulator for phy
+ * vbus_boost: Boost regulator for VBUS present on few Exynos boards
  */
 struct exynos5_usbdrd_phy {
 	struct device *dev;
 	void __iomem *reg_phy;
 	struct clk *clk;
+	struct clk *pipeclk;
+	struct clk *utmiclk;
+	struct clk *itpclk;
 	const struct exynos5_usbdrd_phy_drvdata *drv_data;
 	struct phy_usb_instance {
 		struct phy *phy;
@@ -172,6 +180,7 @@ struct exynos5_usbdrd_phy {
 	u32 extrefclk;
 	struct clk *ref_clk;
 	struct regulator *vbus;
+	struct regulator *vbus_boost;
 };
 
 static inline
@@ -447,13 +456,27 @@ static int exynos5_usbdrd_phy_power_on(struct phy *phy)
 	dev_dbg(phy_drd->dev, "Request to power_on usbdrd_phy phy\n");
 
 	clk_prepare_enable(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_prepare_enable(phy_drd->pipeclk);
+		clk_prepare_enable(phy_drd->utmiclk);
+		clk_prepare_enable(phy_drd->itpclk);
+	}
 
 	/* Enable VBUS supply */
+	if (phy_drd->vbus_boost) {
+		ret = regulator_enable(phy_drd->vbus_boost);
+		if (ret) {
+			dev_err(phy_drd->dev,
+				"Failed to enable VBUS boost supply\n");
+			goto fail_vbus;
+		}
+	}
+
 	if (phy_drd->vbus) {
 		ret = regulator_enable(phy_drd->vbus);
 		if (ret) {
 			dev_err(phy_drd->dev, "Failed to enable VBUS supply\n");
-			goto fail_vbus;
+			goto fail_vbus_boost;
 		}
 	}
 
@@ -462,8 +485,17 @@ static int exynos5_usbdrd_phy_power_on(struct phy *phy)
 
 	return 0;
 
+fail_vbus_boost:
+	if (phy_drd->vbus_boost)
+		regulator_disable(phy_drd->vbus_boost);
+
 fail_vbus:
 	clk_disable_unprepare(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_disable_unprepare(phy_drd->itpclk);
+		clk_disable_unprepare(phy_drd->utmiclk);
+		clk_disable_unprepare(phy_drd->pipeclk);
+	}
 
 	return ret;
 }
@@ -481,8 +513,15 @@ static int exynos5_usbdrd_phy_power_off(struct phy *phy)
 	/* Disable VBUS supply */
 	if (phy_drd->vbus)
 		regulator_disable(phy_drd->vbus);
+	if (phy_drd->vbus_boost)
+		regulator_disable(phy_drd->vbus_boost);
 
 	clk_disable_unprepare(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_disable_unprepare(phy_drd->itpclk);
+		clk_disable_unprepare(phy_drd->pipeclk);
+		clk_disable_unprepare(phy_drd->utmiclk);
+	}
 
 	return 0;
 }
@@ -506,6 +545,57 @@ static struct phy_ops exynos5_usbdrd_phy_ops = {
 	.owner		= THIS_MODULE,
 };
 
+static int exynos5_usbdrd_phy_clk_handle(struct exynos5_usbdrd_phy *phy_drd)
+{
+	unsigned long ref_rate;
+	int ret;
+
+	phy_drd->clk = devm_clk_get(phy_drd->dev, "phy");
+	if (IS_ERR(phy_drd->clk)) {
+		dev_err(phy_drd->dev, "Failed to get phy clock\n");
+		return PTR_ERR(phy_drd->clk);
+	}
+
+	phy_drd->ref_clk = devm_clk_get(phy_drd->dev, "ref");
+	if (IS_ERR(phy_drd->ref_clk)) {
+		dev_err(phy_drd->dev, "Failed to get phy reference clock\n");
+		return PTR_ERR(phy_drd->ref_clk);
+	}
+	ref_rate = clk_get_rate(phy_drd->ref_clk);
+
+	ret = exynos5_rate_to_clk(ref_rate, &phy_drd->extrefclk);
+	if (ret) {
+		dev_err(phy_drd->dev, "Clock rate (%ld) not supported\n",
+			ref_rate);
+		return ret;
+	}
+
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		phy_drd->pipeclk = devm_clk_get(phy_drd->dev, "phy_pipe");
+		if (IS_ERR(phy_drd->pipeclk)) {
+			dev_info(phy_drd->dev,
+				 "PIPE3 phy operational clock not specified\n");
+			phy_drd->pipeclk = NULL;
+		}
+
+		phy_drd->utmiclk = devm_clk_get(phy_drd->dev, "phy_utmi");
+		if (IS_ERR(phy_drd->utmiclk)) {
+			dev_info(phy_drd->dev,
+				 "UTMI phy operational clock not specified\n");
+			phy_drd->utmiclk = NULL;
+		}
+
+		phy_drd->itpclk = devm_clk_get(phy_drd->dev, "itp");
+		if (IS_ERR(phy_drd->itpclk)) {
+			dev_info(phy_drd->dev,
+				 "ITP clock from main OSC not specified\n");
+			phy_drd->itpclk = NULL;
+		}
+	}
+
+	return 0;
+}
+
 static const struct exynos5_usbdrd_phy_config phy_cfg_exynos5[] = {
 	{
 		.id		= EXYNOS5_DRDPHY_UTMI,
@@ -525,11 +615,19 @@ static const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
 	.phy_cfg		= phy_cfg_exynos5,
 	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
 	.pmu_offset_usbdrd1_phy	= EXYNOS5420_USBDRD1_PHY_CONTROL,
+	.has_common_clk_gate	= true,
 };
 
 static const struct exynos5_usbdrd_phy_drvdata exynos5250_usbdrd_phy = {
 	.phy_cfg		= phy_cfg_exynos5,
 	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.has_common_clk_gate	= true,
+};
+
+static const struct exynos5_usbdrd_phy_drvdata exynos7_usbdrd_phy = {
+	.phy_cfg		= phy_cfg_exynos5,
+	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.has_common_clk_gate	= false,
 };
 
 static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
@@ -539,6 +637,9 @@ static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
 	}, {
 		.compatible = "samsung,exynos5420-usbdrd-phy",
 		.data = &exynos5420_usbdrd_phy
+	}, {
+		.compatible = "samsung,exynos7-usbdrd-phy",
+		.data = &exynos7_usbdrd_phy
 	},
 	{ },
 };
@@ -555,7 +656,6 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 	const struct exynos5_usbdrd_phy_drvdata *drv_data;
 	struct regmap *reg_pmu;
 	u32 pmu_offset;
-	unsigned long ref_rate;
 	int i, ret;
 	int channel;
 
@@ -576,23 +676,9 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 	drv_data = match->data;
 	phy_drd->drv_data = drv_data;
 
-	phy_drd->clk = devm_clk_get(dev, "phy");
-	if (IS_ERR(phy_drd->clk)) {
-		dev_err(dev, "Failed to get clock of phy controller\n");
-		return PTR_ERR(phy_drd->clk);
-	}
-
-	phy_drd->ref_clk = devm_clk_get(dev, "ref");
-	if (IS_ERR(phy_drd->ref_clk)) {
-		dev_err(dev, "Failed to get reference clock of usbdrd phy\n");
-		return PTR_ERR(phy_drd->ref_clk);
-	}
-	ref_rate = clk_get_rate(phy_drd->ref_clk);
-
-	ret = exynos5_rate_to_clk(ref_rate, &phy_drd->extrefclk);
+	ret = exynos5_usbdrd_phy_clk_handle(phy_drd);
 	if (ret) {
-		dev_err(phy_drd->dev, "Clock rate (%ld) not supported\n",
-			ref_rate);
+		dev_err(dev, "Failed to initialize clocks\n");
 		return ret;
 	}
 
@@ -622,7 +708,7 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 		break;
 	}
 
-	/* Get Vbus regulator */
+	/* Get Vbus regulators */
 	phy_drd->vbus = devm_regulator_get(dev, "vbus");
 	if (IS_ERR(phy_drd->vbus)) {
 		ret = PTR_ERR(phy_drd->vbus);
@@ -633,12 +719,21 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 		phy_drd->vbus = NULL;
 	}
 
+	phy_drd->vbus_boost = devm_regulator_get(dev, "vbus-boost");
+	if (IS_ERR(phy_drd->vbus_boost)) {
+		ret = PTR_ERR(phy_drd->vbus_boost);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		dev_warn(dev, "Failed to get VBUS boost supply regulator\n");
+		phy_drd->vbus_boost = NULL;
+	}
+
 	dev_vdbg(dev, "Creating usbdrd_phy phy\n");
 
 	for (i = 0; i < EXYNOS5_DRDPHYS_NUM; i++) {
 		struct phy *phy = devm_phy_create(dev, NULL,
-						  &exynos5_usbdrd_phy_ops,
-						  NULL);
+						  &exynos5_usbdrd_phy_ops);
 		if (IS_ERR(phy)) {
 			dev_err(dev, "Failed to create usbdrd_phy phy\n");
 			return PTR_ERR(phy);
diff --git a/drivers/phy/phy-exynos5250-sata.c b/drivers/phy/phy-exynos5250-sata.c
index 54cf4ae60d29..bc858cc800a1 100644
--- a/drivers/phy/phy-exynos5250-sata.c
+++ b/drivers/phy/phy-exynos5250-sata.c
@@ -210,7 +210,7 @@ static int exynos_sata_phy_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	sata_phy->phy = devm_phy_create(dev, NULL, &exynos_sata_phy_ops, NULL);
+	sata_phy->phy = devm_phy_create(dev, NULL, &exynos_sata_phy_ops);
 	if (IS_ERR(sata_phy->phy)) {
 		clk_disable_unprepare(sata_phy->phyclk);
 		dev_err(dev, "failed to create PHY\n");
diff --git a/drivers/phy/phy-hix5hd2-sata.c b/drivers/phy/phy-hix5hd2-sata.c
index d5d978085c6d..34915b4202f1 100644
--- a/drivers/phy/phy-hix5hd2-sata.c
+++ b/drivers/phy/phy-hix5hd2-sata.c
@@ -156,7 +156,7 @@ static int hix5hd2_sata_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->peri_ctrl))
 		priv->peri_ctrl = NULL;
 
-	phy = devm_phy_create(dev, NULL, &hix5hd2_sata_phy_ops, NULL);
+	phy = devm_phy_create(dev, NULL, &hix5hd2_sata_phy_ops);
 	if (IS_ERR(phy)) {
 		dev_err(dev, "failed to create PHY\n");
 		return PTR_ERR(phy);
@@ -164,10 +164,7 @@ static int hix5hd2_sata_phy_probe(struct platform_device *pdev)
 
 	phy_set_drvdata(phy, priv);
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
-	if (IS_ERR(phy_provider))
-		return PTR_ERR(phy_provider);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
 static const struct of_device_id hix5hd2_sata_phy_of_match[] = {
diff --git a/drivers/phy/phy-miphy28lp.c b/drivers/phy/phy-miphy28lp.c
new file mode 100644
index 000000000000..e34da13885e8
--- /dev/null
+++ b/drivers/phy/phy-miphy28lp.c
@@ -0,0 +1,1283 @@
+/*
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * STMicroelectronics PHY driver MiPHY28lp (for SoC STiH407).
+ *
+ * Author: Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <dt-bindings/phy/phy.h>
+
+/* MiPHY registers */
+#define MIPHY_CONF_RESET		0x00
+#define RST_APPLI_SW		BIT(0)
+#define RST_CONF_SW		BIT(1)
+#define RST_MACRO_SW		BIT(2)
+
+#define MIPHY_RESET			0x01
+#define RST_PLL_SW		BIT(0)
+#define RST_COMP_SW		BIT(2)
+
+#define MIPHY_STATUS_1			0x02
+#define PHY_RDY			BIT(0)
+#define HFC_RDY			BIT(1)
+#define HFC_PLL			BIT(2)
+
+#define MIPHY_CONTROL			0x04
+#define TERM_EN_SW		BIT(2)
+#define DIS_LINK_RST		BIT(3)
+#define AUTO_RST_RX		BIT(4)
+#define PX_RX_POL		BIT(5)
+
+#define MIPHY_BOUNDARY_SEL		0x0a
+#define TX_SEL			BIT(6)
+#define SSC_SEL			BIT(4)
+#define GENSEL_SEL		BIT(0)
+
+#define MIPHY_BOUNDARY_1		0x0b
+#define MIPHY_BOUNDARY_2		0x0c
+#define SSC_EN_SW		BIT(2)
+
+#define MIPHY_PLL_CLKREF_FREQ		0x0d
+#define MIPHY_SPEED			0x0e
+#define TX_SPDSEL_80DEC		0
+#define TX_SPDSEL_40DEC		1
+#define TX_SPDSEL_20DEC		2
+#define RX_SPDSEL_80DEC		0
+#define RX_SPDSEL_40DEC		(1 << 2)
+#define RX_SPDSEL_20DEC		(2 << 2)
+
+#define MIPHY_CONF			0x0f
+#define MIPHY_CTRL_TEST_SEL		0x20
+#define MIPHY_CTRL_TEST_1		0x21
+#define MIPHY_CTRL_TEST_2		0x22
+#define MIPHY_CTRL_TEST_3		0x23
+#define MIPHY_CTRL_TEST_4		0x24
+#define MIPHY_FEEDBACK_TEST		0x25
+#define MIPHY_DEBUG_BUS			0x26
+#define MIPHY_DEBUG_STATUS_MSB		0x27
+#define MIPHY_DEBUG_STATUS_LSB		0x28
+#define MIPHY_PWR_RAIL_1		0x29
+#define MIPHY_PWR_RAIL_2		0x2a
+#define MIPHY_SYNCHAR_CONTROL		0x30
+
+#define MIPHY_COMP_FSM_1		0x3a
+#define COMP_START		BIT(6)
+
+#define MIPHY_COMP_FSM_6		0x3f
+#define COMP_DONE		BIT(7)
+
+#define MIPHY_COMP_POSTP		0x42
+#define MIPHY_TX_CTRL_1			0x49
+#define TX_REG_STEP_0V		0
+#define TX_REG_STEP_P_25MV	1
+#define TX_REG_STEP_P_50MV	2
+#define TX_REG_STEP_N_25MV	7
+#define TX_REG_STEP_N_50MV	6
+#define TX_REG_STEP_N_75MV	5
+
+#define MIPHY_TX_CTRL_2			0x4a
+#define TX_SLEW_SW_40_PS	0
+#define TX_SLEW_SW_80_PS	1
+#define TX_SLEW_SW_120_PS	2
+
+#define MIPHY_TX_CTRL_3			0x4b
+#define MIPHY_TX_CAL_MAN		0x4e
+#define TX_SLEW_CAL_MAN_EN	BIT(0)
+
+#define MIPHY_TST_BIAS_BOOST_2		0x62
+#define MIPHY_BIAS_BOOST_1		0x63
+#define MIPHY_BIAS_BOOST_2		0x64
+#define MIPHY_RX_DESBUFF_FDB_2		0x67
+#define MIPHY_RX_DESBUFF_FDB_3		0x68
+#define MIPHY_SIGDET_COMPENS1		0x69
+#define MIPHY_SIGDET_COMPENS2		0x6a
+#define MIPHY_JITTER_PERIOD		0x6b
+#define MIPHY_JITTER_AMPLITUDE_1	0x6c
+#define MIPHY_JITTER_AMPLITUDE_2	0x6d
+#define MIPHY_JITTER_AMPLITUDE_3	0x6e
+#define MIPHY_RX_K_GAIN			0x78
+#define MIPHY_RX_BUFFER_CTRL		0x7a
+#define VGA_GAIN		BIT(0)
+#define EQ_DC_GAIN		BIT(2)
+#define EQ_BOOST_GAIN		BIT(3)
+
+#define MIPHY_RX_VGA_GAIN		0x7b
+#define MIPHY_RX_EQU_GAIN_1		0x7f
+#define MIPHY_RX_EQU_GAIN_2		0x80
+#define MIPHY_RX_EQU_GAIN_3		0x81
+#define MIPHY_RX_CAL_CTRL_1		0x97
+#define MIPHY_RX_CAL_CTRL_2		0x98
+
+#define MIPHY_RX_CAL_OFFSET_CTRL	0x99
+#define CAL_OFFSET_VGA_64	(0x03 << 0)
+#define CAL_OFFSET_THRESHOLD_64	(0x03 << 2)
+#define VGA_OFFSET_POLARITY	BIT(4)
+#define OFFSET_COMPENSATION_EN	BIT(6)
+
+#define MIPHY_RX_CAL_VGA_STEP		0x9a
+#define MIPHY_RX_CAL_EYE_MIN		0x9d
+#define MIPHY_RX_CAL_OPT_LENGTH		0x9f
+#define MIPHY_RX_LOCK_CTRL_1		0xc1
+#define MIPHY_RX_LOCK_SETTINGS_OPT	0xc2
+#define MIPHY_RX_LOCK_STEP		0xc4
+
+#define MIPHY_RX_SIGDET_SLEEP_OA	0xc9
+#define MIPHY_RX_SIGDET_SLEEP_SEL	0xca
+#define MIPHY_RX_SIGDET_WAIT_SEL	0xcb
+#define MIPHY_RX_SIGDET_DATA_SEL	0xcc
+#define EN_ULTRA_LOW_POWER	BIT(0)
+#define EN_FIRST_HALF		BIT(1)
+#define EN_SECOND_HALF		BIT(2)
+#define EN_DIGIT_SIGNAL_CHECK	BIT(3)
+
+#define MIPHY_RX_POWER_CTRL_1		0xcd
+#define MIPHY_RX_POWER_CTRL_2		0xce
+#define MIPHY_PLL_CALSET_CTRL		0xd3
+#define MIPHY_PLL_CALSET_1		0xd4
+#define MIPHY_PLL_CALSET_2		0xd5
+#define MIPHY_PLL_CALSET_3		0xd6
+#define MIPHY_PLL_CALSET_4		0xd7
+#define MIPHY_PLL_SBR_1			0xe3
+#define SET_NEW_CHANGE		BIT(1)
+
+#define MIPHY_PLL_SBR_2			0xe4
+#define MIPHY_PLL_SBR_3			0xe5
+#define MIPHY_PLL_SBR_4			0xe6
+#define MIPHY_PLL_COMMON_MISC_2		0xe9
+#define START_ACT_FILT		BIT(6)
+
+#define MIPHY_PLL_SPAREIN		0xeb
+
+/*
+ * On STiH407 the glue logic can be different among MiPHY devices; for example:
+ * MiPHY0: OSC_FORCE_EXT means:
+ *  0: 30MHz crystal clk - 1: 100MHz ext clk routed through MiPHY1
+ * MiPHY1: OSC_FORCE_EXT means:
+ *  1: 30MHz crystal clk - 0: 100MHz ext clk routed through MiPHY1
+ * Some devices have not the possibility to check if the osc is ready.
+ */
+#define MIPHY_OSC_FORCE_EXT	BIT(3)
+#define MIPHY_OSC_RDY		BIT(5)
+
+#define MIPHY_CTRL_MASK		0x0f
+#define MIPHY_CTRL_DEFAULT	0
+#define MIPHY_CTRL_SYNC_D_EN	BIT(2)
+
+/* SATA / PCIe defines */
+#define SATA_CTRL_MASK		0x07
+#define PCIE_CTRL_MASK		0xff
+#define SATA_CTRL_SELECT_SATA	1
+#define SATA_CTRL_SELECT_PCIE	0
+#define SYSCFG_PCIE_PCIE_VAL	0x80
+#define SATA_SPDMODE		1
+
+#define MIPHY_SATA_BANK_NB	3
+#define MIPHY_PCIE_BANK_NB	2
+
+struct miphy28lp_phy {
+	struct phy *phy;
+	struct miphy28lp_dev *phydev;
+	void __iomem *base;
+	void __iomem *pipebase;
+
+	bool osc_force_ext;
+	bool osc_rdy;
+	bool px_rx_pol_inv;
+	bool ssc;
+	bool tx_impedance;
+
+	struct reset_control *miphy_rst;
+
+	u32 sata_gen;
+
+	/* Sysconfig registers offsets needed to configure the device */
+	u32 syscfg_miphy_ctrl;
+	u32 syscfg_miphy_status;
+	u32 syscfg_pci;
+	u32 syscfg_sata;
+	u8 type;
+};
+
+struct miphy28lp_dev {
+	struct device *dev;
+	struct regmap *regmap;
+	struct mutex miphy_mutex;
+	struct miphy28lp_phy **phys;
+};
+
+struct miphy_initval {
+	u16 reg;
+	u16 val;
+};
+
+enum miphy_sata_gen { SATA_GEN1, SATA_GEN2, SATA_GEN3 };
+
+static char *PHY_TYPE_name[] = { "sata-up", "pcie-up", "", "usb3-up" };
+
+struct pll_ratio {
+	int clk_ref;
+	int calset_1;
+	int calset_2;
+	int calset_3;
+	int calset_4;
+	int cal_ctrl;
+};
+
+static struct pll_ratio sata_pll_ratio = {
+	.clk_ref = 0x1e,
+	.calset_1 = 0xc8,
+	.calset_2 = 0x00,
+	.calset_3 = 0x00,
+	.calset_4 = 0x00,
+	.cal_ctrl = 0x00,
+};
+
+static struct pll_ratio pcie_pll_ratio = {
+	.clk_ref = 0x1e,
+	.calset_1 = 0xa6,
+	.calset_2 = 0xaa,
+	.calset_3 = 0xaa,
+	.calset_4 = 0x00,
+	.cal_ctrl = 0x00,
+};
+
+static struct pll_ratio usb3_pll_ratio = {
+	.clk_ref = 0x1e,
+	.calset_1 = 0xa6,
+	.calset_2 = 0xaa,
+	.calset_3 = 0xaa,
+	.calset_4 = 0x04,
+	.cal_ctrl = 0x00,
+};
+
+struct miphy28lp_pll_gen {
+	int bank;
+	int speed;
+	int bias_boost_1;
+	int bias_boost_2;
+	int tx_ctrl_1;
+	int tx_ctrl_2;
+	int tx_ctrl_3;
+	int rx_k_gain;
+	int rx_vga_gain;
+	int rx_equ_gain_1;
+	int rx_equ_gain_2;
+	int rx_equ_gain_3;
+	int rx_buff_ctrl;
+};
+
+static struct miphy28lp_pll_gen sata_pll_gen[] = {
+	{
+		.bank		= 0x00,
+		.speed		= TX_SPDSEL_80DEC | RX_SPDSEL_80DEC,
+		.bias_boost_1	= 0x00,
+		.bias_boost_2	= 0xae,
+		.tx_ctrl_2	= 0x53,
+		.tx_ctrl_3	= 0x00,
+		.rx_buff_ctrl	= EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+		.rx_vga_gain	= 0x00,
+		.rx_equ_gain_1	= 0x7d,
+		.rx_equ_gain_2	= 0x56,
+		.rx_equ_gain_3	= 0x00,
+	},
+	{
+		.bank		= 0x01,
+		.speed		= TX_SPDSEL_40DEC | RX_SPDSEL_40DEC,
+		.bias_boost_1	= 0x00,
+		.bias_boost_2	= 0xae,
+		.tx_ctrl_2	= 0x72,
+		.tx_ctrl_3	= 0x20,
+		.rx_buff_ctrl	= EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+		.rx_vga_gain	= 0x00,
+		.rx_equ_gain_1	= 0x7d,
+		.rx_equ_gain_2	= 0x56,
+		.rx_equ_gain_3	= 0x00,
+	},
+	{
+		.bank		= 0x02,
+		.speed		= TX_SPDSEL_20DEC | RX_SPDSEL_20DEC,
+		.bias_boost_1	= 0x00,
+		.bias_boost_2	= 0xae,
+		.tx_ctrl_2	= 0xc0,
+		.tx_ctrl_3	= 0x20,
+		.rx_buff_ctrl	= EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+		.rx_vga_gain	= 0x00,
+		.rx_equ_gain_1	= 0x7d,
+		.rx_equ_gain_2	= 0x56,
+		.rx_equ_gain_3	= 0x00,
+	},
+};
+
+static struct miphy28lp_pll_gen pcie_pll_gen[] = {
+	{
+		.bank		= 0x00,
+		.speed		= TX_SPDSEL_40DEC | RX_SPDSEL_40DEC,
+		.bias_boost_1	= 0x00,
+		.bias_boost_2	= 0xa5,
+		.tx_ctrl_1	= TX_REG_STEP_N_25MV,
+		.tx_ctrl_2	= 0x71,
+		.tx_ctrl_3	= 0x60,
+		.rx_k_gain	= 0x98,
+		.rx_buff_ctrl	= EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+		.rx_vga_gain	= 0x00,
+		.rx_equ_gain_1	= 0x79,
+		.rx_equ_gain_2	= 0x56,
+	},
+	{
+		.bank		= 0x01,
+		.speed		= TX_SPDSEL_20DEC | RX_SPDSEL_20DEC,
+		.bias_boost_1	= 0x00,
+		.bias_boost_2	= 0xa5,
+		.tx_ctrl_1	= TX_REG_STEP_N_25MV,
+		.tx_ctrl_2	= 0x70,
+		.tx_ctrl_3	= 0x60,
+		.rx_k_gain	= 0xcc,
+		.rx_buff_ctrl	= EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+		.rx_vga_gain	= 0x00,
+		.rx_equ_gain_1	= 0x78,
+		.rx_equ_gain_2	= 0x07,
+	},
+};
+
+static inline void miphy28lp_set_reset(struct miphy28lp_phy *miphy_phy)
+{
+	void *base = miphy_phy->base;
+	u8 val;
+
+	/* Putting Macro in reset */
+	writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+
+	val = RST_APPLI_SW | RST_CONF_SW;
+	writeb_relaxed(val, base + MIPHY_CONF_RESET);
+
+	writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+
+	/* Bringing the MIPHY-CPU registers out of reset */
+	if (miphy_phy->type == PHY_TYPE_PCIE) {
+		val = AUTO_RST_RX | TERM_EN_SW;
+		writeb_relaxed(val, base + MIPHY_CONTROL);
+	} else {
+		val = AUTO_RST_RX | TERM_EN_SW | DIS_LINK_RST;
+		writeb_relaxed(val, base + MIPHY_CONTROL);
+	}
+}
+
+static inline void miphy28lp_pll_calibration(struct miphy28lp_phy *miphy_phy,
+		struct pll_ratio *pll_ratio)
+{
+	void *base = miphy_phy->base;
+	u8 val;
+
+	/* Applying PLL Settings */
+	writeb_relaxed(0x1d, base + MIPHY_PLL_SPAREIN);
+	writeb_relaxed(pll_ratio->clk_ref, base + MIPHY_PLL_CLKREF_FREQ);
+
+	/* PLL Ratio */
+	writeb_relaxed(pll_ratio->calset_1, base + MIPHY_PLL_CALSET_1);
+	writeb_relaxed(pll_ratio->calset_2, base + MIPHY_PLL_CALSET_2);
+	writeb_relaxed(pll_ratio->calset_3, base + MIPHY_PLL_CALSET_3);
+	writeb_relaxed(pll_ratio->calset_4, base + MIPHY_PLL_CALSET_4);
+	writeb_relaxed(pll_ratio->cal_ctrl, base + MIPHY_PLL_CALSET_CTRL);
+
+	writeb_relaxed(TX_SEL, base + MIPHY_BOUNDARY_SEL);
+
+	val = (0x68 << 1) | TX_SLEW_CAL_MAN_EN;
+	writeb_relaxed(val, base + MIPHY_TX_CAL_MAN);
+
+	val = VGA_OFFSET_POLARITY | CAL_OFFSET_THRESHOLD_64 | CAL_OFFSET_VGA_64;
+
+	if (miphy_phy->type != PHY_TYPE_SATA)
+		val |= OFFSET_COMPENSATION_EN;
+
+	writeb_relaxed(val, base + MIPHY_RX_CAL_OFFSET_CTRL);
+
+	if (miphy_phy->type == PHY_TYPE_USB3) {
+		writeb_relaxed(0x00, base + MIPHY_CONF);
+		writeb_relaxed(0x70, base + MIPHY_RX_LOCK_STEP);
+		writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_SLEEP_OA);
+		writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_SLEEP_SEL);
+		writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_WAIT_SEL);
+
+		val = EN_DIGIT_SIGNAL_CHECK | EN_FIRST_HALF;
+		writeb_relaxed(val, base + MIPHY_RX_SIGDET_DATA_SEL);
+	}
+
+}
+
+static inline void miphy28lp_sata_config_gen(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(sata_pll_gen); i++) {
+		struct miphy28lp_pll_gen *gen = &sata_pll_gen[i];
+
+		/* Banked settings */
+		writeb_relaxed(gen->bank, base + MIPHY_CONF);
+		writeb_relaxed(gen->speed, base + MIPHY_SPEED);
+		writeb_relaxed(gen->bias_boost_1, base + MIPHY_BIAS_BOOST_1);
+		writeb_relaxed(gen->bias_boost_2, base + MIPHY_BIAS_BOOST_2);
+
+		/* TX buffer Settings */
+		writeb_relaxed(gen->tx_ctrl_2, base + MIPHY_TX_CTRL_2);
+		writeb_relaxed(gen->tx_ctrl_3, base + MIPHY_TX_CTRL_3);
+
+		/* RX Buffer Settings */
+		writeb_relaxed(gen->rx_buff_ctrl, base + MIPHY_RX_BUFFER_CTRL);
+		writeb_relaxed(gen->rx_vga_gain, base + MIPHY_RX_VGA_GAIN);
+		writeb_relaxed(gen->rx_equ_gain_1, base + MIPHY_RX_EQU_GAIN_1);
+		writeb_relaxed(gen->rx_equ_gain_2, base + MIPHY_RX_EQU_GAIN_2);
+		writeb_relaxed(gen->rx_equ_gain_3, base + MIPHY_RX_EQU_GAIN_3);
+	}
+}
+
+static inline void miphy28lp_pcie_config_gen(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcie_pll_gen); i++) {
+		struct miphy28lp_pll_gen *gen = &pcie_pll_gen[i];
+
+		/* Banked settings */
+		writeb_relaxed(gen->bank, base + MIPHY_CONF);
+		writeb_relaxed(gen->speed, base + MIPHY_SPEED);
+		writeb_relaxed(gen->bias_boost_1, base + MIPHY_BIAS_BOOST_1);
+		writeb_relaxed(gen->bias_boost_2, base + MIPHY_BIAS_BOOST_2);
+
+		/* TX buffer Settings */
+		writeb_relaxed(gen->tx_ctrl_1, base + MIPHY_TX_CTRL_1);
+		writeb_relaxed(gen->tx_ctrl_2, base + MIPHY_TX_CTRL_2);
+		writeb_relaxed(gen->tx_ctrl_3, base + MIPHY_TX_CTRL_3);
+
+		writeb_relaxed(gen->rx_k_gain, base + MIPHY_RX_K_GAIN);
+
+		/* RX Buffer Settings */
+		writeb_relaxed(gen->rx_buff_ctrl, base + MIPHY_RX_BUFFER_CTRL);
+		writeb_relaxed(gen->rx_vga_gain, base + MIPHY_RX_VGA_GAIN);
+		writeb_relaxed(gen->rx_equ_gain_1, base + MIPHY_RX_EQU_GAIN_1);
+		writeb_relaxed(gen->rx_equ_gain_2, base + MIPHY_RX_EQU_GAIN_2);
+	}
+}
+
+static inline int miphy28lp_wait_compensation(struct miphy28lp_phy *miphy_phy)
+{
+	unsigned long finish = jiffies + 5 * HZ;
+	u8 val;
+
+	/* Waiting for Compensation to complete */
+	do {
+		val = readb_relaxed(miphy_phy->base + MIPHY_COMP_FSM_6);
+
+		if (time_after_eq(jiffies, finish))
+			return -EBUSY;
+		cpu_relax();
+	} while (!(val & COMP_DONE));
+
+	return 0;
+}
+
+
+static inline int miphy28lp_compensation(struct miphy28lp_phy *miphy_phy,
+		struct pll_ratio *pll_ratio)
+{
+	void __iomem *base = miphy_phy->base;
+
+	/* Poll for HFC ready after reset release */
+	/* Compensation measurement */
+	writeb_relaxed(RST_PLL_SW | RST_COMP_SW, base + MIPHY_RESET);
+
+	writeb_relaxed(0x00, base + MIPHY_PLL_COMMON_MISC_2);
+	writeb_relaxed(pll_ratio->clk_ref, base + MIPHY_PLL_CLKREF_FREQ);
+	writeb_relaxed(COMP_START, base + MIPHY_COMP_FSM_1);
+
+	if (miphy_phy->type == PHY_TYPE_PCIE)
+		writeb_relaxed(RST_PLL_SW, base + MIPHY_RESET);
+
+	writeb_relaxed(0x00, base + MIPHY_RESET);
+	writeb_relaxed(START_ACT_FILT, base + MIPHY_PLL_COMMON_MISC_2);
+	writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+	/* TX compensation offset to re-center TX impedance */
+	writeb_relaxed(0x00, base + MIPHY_COMP_POSTP);
+
+	if (miphy_phy->type == PHY_TYPE_PCIE)
+		return miphy28lp_wait_compensation(miphy_phy);
+
+	return 0;
+}
+
+static inline void miphy28_usb3_miphy_reset(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	u8 val;
+
+	/* MIPHY Reset */
+	writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+	writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+	writeb_relaxed(RST_COMP_SW, base + MIPHY_RESET);
+
+	val = RST_COMP_SW | RST_PLL_SW;
+	writeb_relaxed(val, base + MIPHY_RESET);
+
+	writeb_relaxed(0x00, base + MIPHY_PLL_COMMON_MISC_2);
+	writeb_relaxed(0x1e, base + MIPHY_PLL_CLKREF_FREQ);
+	writeb_relaxed(COMP_START, base + MIPHY_COMP_FSM_1);
+	writeb_relaxed(RST_PLL_SW, base + MIPHY_RESET);
+	writeb_relaxed(0x00, base + MIPHY_RESET);
+	writeb_relaxed(START_ACT_FILT, base + MIPHY_PLL_COMMON_MISC_2);
+	writeb_relaxed(0x00, base + MIPHY_CONF);
+	writeb_relaxed(0x00, base + MIPHY_BOUNDARY_1);
+	writeb_relaxed(0x00, base + MIPHY_TST_BIAS_BOOST_2);
+	writeb_relaxed(0x00, base + MIPHY_CONF);
+	writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+	writeb_relaxed(0xa5, base + MIPHY_DEBUG_BUS);
+	writeb_relaxed(0x00, base + MIPHY_CONF);
+}
+
+static void miphy_sata_tune_ssc(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	u8 val;
+
+	/* Compensate Tx impedance to avoid out of range values */
+	/*
+	 * Enable the SSC on PLL for all banks
+	 * SSC Modulation @ 31 KHz and 4000 ppm modulation amp
+	 */
+	val = readb_relaxed(base + MIPHY_BOUNDARY_2);
+	val |= SSC_EN_SW;
+	writeb_relaxed(val, base + MIPHY_BOUNDARY_2);
+
+	val = readb_relaxed(base + MIPHY_BOUNDARY_SEL);
+	val |= SSC_SEL;
+	writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+	for (val = 0; val < MIPHY_SATA_BANK_NB; val++) {
+		writeb_relaxed(val, base + MIPHY_CONF);
+
+		/* Add value to each reference clock cycle  */
+		/* and define the period length of the SSC */
+		writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+		writeb_relaxed(0x6c, base + MIPHY_PLL_SBR_3);
+		writeb_relaxed(0x81, base + MIPHY_PLL_SBR_4);
+
+		/* Clear any previous request */
+		writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+		/* requests the PLL to take in account new parameters */
+		writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+		/* To be sure there is no other pending requests */
+		writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+	}
+}
+
+static void miphy_pcie_tune_ssc(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	u8 val;
+
+	/* Compensate Tx impedance to avoid out of range values */
+	/*
+	 * Enable the SSC on PLL for all banks
+	 * SSC Modulation @ 31 KHz and 4000 ppm modulation amp
+	 */
+	val = readb_relaxed(base + MIPHY_BOUNDARY_2);
+	val |= SSC_EN_SW;
+	writeb_relaxed(val, base + MIPHY_BOUNDARY_2);
+
+	val = readb_relaxed(base + MIPHY_BOUNDARY_SEL);
+	val |= SSC_SEL;
+	writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+	for (val = 0; val < MIPHY_PCIE_BANK_NB; val++) {
+		writeb_relaxed(val, base + MIPHY_CONF);
+
+		/* Validate Step component */
+		writeb_relaxed(0x69, base + MIPHY_PLL_SBR_3);
+		writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+		/* Validate Period component */
+		writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+		writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+		/* Clear any previous request */
+		writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+		/* requests the PLL to take in account new parameters */
+		writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+		/* To be sure there is no other pending requests */
+		writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+	}
+}
+
+static inline void miphy_tune_tx_impedance(struct miphy28lp_phy *miphy_phy)
+{
+	/* Compensate Tx impedance to avoid out of range values */
+	writeb_relaxed(0x02, miphy_phy->base + MIPHY_COMP_POSTP);
+}
+
+static inline int miphy28lp_configure_sata(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	int err;
+	u8 val;
+
+	/* Putting Macro in reset */
+	miphy28lp_set_reset(miphy_phy);
+
+	/* PLL calibration */
+	miphy28lp_pll_calibration(miphy_phy, &sata_pll_ratio);
+
+	/* Banked settings Gen1/Gen2/Gen3 */
+	miphy28lp_sata_config_gen(miphy_phy);
+
+	/* Power control */
+	/* Input bridge enable, manual input bridge control */
+	writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+
+	/* Macro out of reset */
+	writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+
+	/* Poll for HFC ready after reset release */
+	/* Compensation measurement */
+	err = miphy28lp_compensation(miphy_phy, &sata_pll_ratio);
+	if (err)
+		return err;
+
+	if (miphy_phy->px_rx_pol_inv) {
+		/* Invert Rx polarity */
+		val = readb_relaxed(miphy_phy->base + MIPHY_CONTROL);
+		val |= PX_RX_POL;
+		writeb_relaxed(val, miphy_phy->base + MIPHY_CONTROL);
+	}
+
+	if (miphy_phy->ssc)
+		miphy_sata_tune_ssc(miphy_phy);
+
+	if (miphy_phy->tx_impedance)
+		miphy_tune_tx_impedance(miphy_phy);
+
+	return 0;
+}
+
+static inline int miphy28lp_configure_pcie(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	int err;
+
+	/* Putting Macro in reset */
+	miphy28lp_set_reset(miphy_phy);
+
+	/* PLL calibration */
+	miphy28lp_pll_calibration(miphy_phy, &pcie_pll_ratio);
+
+	/* Banked settings Gen1/Gen2 */
+	miphy28lp_pcie_config_gen(miphy_phy);
+
+	/* Power control */
+	/* Input bridge enable, manual input bridge control */
+	writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+
+	/* Macro out of reset */
+	writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+
+	/* Poll for HFC ready after reset release */
+	/* Compensation measurement */
+	err = miphy28lp_compensation(miphy_phy, &pcie_pll_ratio);
+	if (err)
+		return err;
+
+	if (miphy_phy->ssc)
+		miphy_pcie_tune_ssc(miphy_phy);
+
+	if (miphy_phy->tx_impedance)
+		miphy_tune_tx_impedance(miphy_phy);
+
+	return 0;
+}
+
+
+static inline void miphy28lp_configure_usb3(struct miphy28lp_phy *miphy_phy)
+{
+	void __iomem *base = miphy_phy->base;
+	u8 val;
+
+	/* Putting Macro in reset */
+	miphy28lp_set_reset(miphy_phy);
+
+	/* PLL calibration */
+	miphy28lp_pll_calibration(miphy_phy, &usb3_pll_ratio);
+
+	/* Writing The Speed Rate */
+	writeb_relaxed(0x00, base + MIPHY_CONF);
+
+	val = RX_SPDSEL_20DEC | TX_SPDSEL_20DEC;
+	writeb_relaxed(val, base + MIPHY_SPEED);
+
+	/* RX Channel compensation and calibration */
+	writeb_relaxed(0x1c, base + MIPHY_RX_LOCK_SETTINGS_OPT);
+	writeb_relaxed(0x51, base + MIPHY_RX_CAL_CTRL_1);
+	writeb_relaxed(0x70, base + MIPHY_RX_CAL_CTRL_2);
+
+	val = OFFSET_COMPENSATION_EN | VGA_OFFSET_POLARITY |
+	      CAL_OFFSET_THRESHOLD_64 | CAL_OFFSET_VGA_64;
+	writeb_relaxed(val, base + MIPHY_RX_CAL_OFFSET_CTRL);
+	writeb_relaxed(0x22, base + MIPHY_RX_CAL_VGA_STEP);
+	writeb_relaxed(0x0e, base + MIPHY_RX_CAL_OPT_LENGTH);
+
+	val = EQ_DC_GAIN | VGA_GAIN;
+	writeb_relaxed(val, base + MIPHY_RX_BUFFER_CTRL);
+	writeb_relaxed(0x78, base + MIPHY_RX_EQU_GAIN_1);
+	writeb_relaxed(0x1b, base + MIPHY_SYNCHAR_CONTROL);
+
+	/* TX compensation offset to re-center TX impedance */
+	writeb_relaxed(0x02, base + MIPHY_COMP_POSTP);
+
+	/* Enable GENSEL_SEL and SSC */
+	/* TX_SEL=0 swing preemp forced by pipe registres */
+	val = SSC_SEL | GENSEL_SEL;
+	writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+	/* MIPHY Bias boost */
+	writeb_relaxed(0x00, base + MIPHY_BIAS_BOOST_1);
+	writeb_relaxed(0xa7, base + MIPHY_BIAS_BOOST_2);
+
+	/* SSC modulation */
+	writeb_relaxed(SSC_EN_SW, base + MIPHY_BOUNDARY_2);
+
+	/* MIPHY TX control */
+	writeb_relaxed(0x00, base + MIPHY_CONF);
+
+	/* Validate Step component */
+	writeb_relaxed(0x5a, base + MIPHY_PLL_SBR_3);
+	writeb_relaxed(0xa0, base + MIPHY_PLL_SBR_4);
+
+	/* Validate Period component */
+	writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+	writeb_relaxed(0xa1, base + MIPHY_PLL_SBR_4);
+
+	/* Clear any previous request */
+	writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+	/* requests the PLL to take in account new parameters */
+	writeb_relaxed(0x02, base + MIPHY_PLL_SBR_1);
+
+	/* To be sure there is no other pending requests */
+	writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+	/* Rx PI controller settings */
+	writeb_relaxed(0xca, base + MIPHY_RX_K_GAIN);
+
+	/* MIPHY RX input bridge control */
+	/* INPUT_BRIDGE_EN_SW=1, manual input bridge control[0]=1 */
+	writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+	writeb_relaxed(0x29, base + MIPHY_RX_POWER_CTRL_1);
+	writeb_relaxed(0x1a, base + MIPHY_RX_POWER_CTRL_2);
+
+	/* MIPHY Reset for usb3 */
+	miphy28_usb3_miphy_reset(miphy_phy);
+}
+
+static inline int miphy_is_ready(struct miphy28lp_phy *miphy_phy)
+{
+	unsigned long finish = jiffies + 5 * HZ;
+	u8 mask = HFC_PLL | HFC_RDY;
+	u8 val;
+
+	/*
+	 * For PCIe and USB3 check only that PLL and HFC are ready
+	 * For SATA check also that phy is ready!
+	 */
+	if (miphy_phy->type == PHY_TYPE_SATA)
+		mask |= PHY_RDY;
+
+	do {
+		val = readb_relaxed(miphy_phy->base + MIPHY_STATUS_1);
+		if ((val & mask) != mask)
+			cpu_relax();
+		else
+			return 0;
+	} while (!time_after_eq(jiffies, finish));
+
+	return -EBUSY;
+}
+
+static int miphy_osc_is_ready(struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	unsigned long finish = jiffies + 5 * HZ;
+	u32 val;
+
+	if (!miphy_phy->osc_rdy)
+		return 0;
+
+	if (!miphy_phy->syscfg_miphy_status)
+		return -EINVAL;
+
+	do {
+		regmap_read(miphy_dev->regmap, miphy_phy->syscfg_miphy_status,
+			    &val);
+
+		if ((val & MIPHY_OSC_RDY) != MIPHY_OSC_RDY)
+			cpu_relax();
+		else
+			return 0;
+	} while (!time_after_eq(jiffies, finish));
+
+	return -EBUSY;
+}
+
+static int miphy28lp_get_resource_byname(struct device_node *child,
+					  char *rname, struct resource *res)
+{
+	int index;
+
+	index = of_property_match_string(child, "reg-names", rname);
+	if (index < 0)
+		return -ENODEV;
+
+	return of_address_to_resource(child, index, res);
+}
+
+static int miphy28lp_get_one_addr(struct device *dev,
+				  struct device_node *child, char *rname,
+				  void __iomem **base)
+{
+	struct resource res;
+	int ret;
+
+	ret = miphy28lp_get_resource_byname(child, rname, &res);
+	if (!ret) {
+		*base = devm_ioremap(dev, res.start, resource_size(&res));
+		if (!*base) {
+			dev_err(dev, "failed to ioremap %s address region\n"
+					, rname);
+			return -ENOENT;
+		}
+	}
+
+	return 0;
+}
+
+/* MiPHY reset and sysconf setup */
+static int miphy28lp_setup(struct miphy28lp_phy *miphy_phy, u32 miphy_val)
+{
+	int err;
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+
+	if (!miphy_phy->syscfg_miphy_ctrl)
+		return -EINVAL;
+
+	err = reset_control_assert(miphy_phy->miphy_rst);
+	if (err) {
+		dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+		return err;
+	}
+
+	if (miphy_phy->osc_force_ext)
+		miphy_val |= MIPHY_OSC_FORCE_EXT;
+
+	regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_miphy_ctrl,
+			   MIPHY_CTRL_MASK, miphy_val);
+
+	err = reset_control_deassert(miphy_phy->miphy_rst);
+	if (err) {
+		dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+		return err;
+	}
+
+	return miphy_osc_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_sata(struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	int err, sata_conf = SATA_CTRL_SELECT_SATA;
+
+	if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
+		|| (!miphy_phy->base))
+		return -EINVAL;
+
+	dev_info(miphy_dev->dev, "sata-up mode, addr 0x%p\n", miphy_phy->base);
+
+	/* Configure the glue-logic */
+	sata_conf |= ((miphy_phy->sata_gen - SATA_GEN1) << SATA_SPDMODE);
+
+	regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+			   SATA_CTRL_MASK, sata_conf);
+
+	regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+			   PCIE_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
+
+	/* MiPHY path and clocking init */
+	err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_DEFAULT);
+
+	if (err) {
+		dev_err(miphy_dev->dev, "SATA phy setup failed\n");
+		return err;
+	}
+
+	/* initialize miphy */
+	miphy28lp_configure_sata(miphy_phy);
+
+	return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_pcie(struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	int err;
+
+	if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
+		|| (!miphy_phy->base) || (!miphy_phy->pipebase))
+		return -EINVAL;
+
+	dev_info(miphy_dev->dev, "pcie-up mode, addr 0x%p\n", miphy_phy->base);
+
+	/* Configure the glue-logic */
+	regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+			   SATA_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
+
+	regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+			   PCIE_CTRL_MASK, SYSCFG_PCIE_PCIE_VAL);
+
+	/* MiPHY path and clocking init */
+	err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_DEFAULT);
+
+	if (err) {
+		dev_err(miphy_dev->dev, "PCIe phy setup failed\n");
+		return err;
+	}
+
+	/* initialize miphy */
+	err = miphy28lp_configure_pcie(miphy_phy);
+	if (err)
+		return err;
+
+	/* PIPE Wrapper Configuration */
+	writeb_relaxed(0x68, miphy_phy->pipebase + 0x104); /* Rise_0 */
+	writeb_relaxed(0x61, miphy_phy->pipebase + 0x105); /* Rise_1 */
+	writeb_relaxed(0x68, miphy_phy->pipebase + 0x108); /* Fall_0 */
+	writeb_relaxed(0x61, miphy_phy->pipebase + 0x109); /* Fall-1 */
+	writeb_relaxed(0x68, miphy_phy->pipebase + 0x10c); /* Threshold_0 */
+	writeb_relaxed(0x60, miphy_phy->pipebase + 0x10d); /* Threshold_1 */
+
+	/* Wait for phy_ready */
+	return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_usb3(struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	int err;
+
+	if ((!miphy_phy->base) || (!miphy_phy->pipebase))
+		return -EINVAL;
+
+	dev_info(miphy_dev->dev, "usb3-up mode, addr 0x%p\n", miphy_phy->base);
+
+	/* MiPHY path and clocking init */
+	err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_SYNC_D_EN);
+	if (err) {
+		dev_err(miphy_dev->dev, "USB3 phy setup failed\n");
+		return err;
+	}
+
+	/* initialize miphy */
+	miphy28lp_configure_usb3(miphy_phy);
+
+	/* PIPE Wrapper Configuration */
+	writeb_relaxed(0x68, miphy_phy->pipebase + 0x23);
+	writeb_relaxed(0x61, miphy_phy->pipebase + 0x24);
+	writeb_relaxed(0x68, miphy_phy->pipebase + 0x26);
+	writeb_relaxed(0x61, miphy_phy->pipebase + 0x27);
+	writeb_relaxed(0x18, miphy_phy->pipebase + 0x29);
+	writeb_relaxed(0x61, miphy_phy->pipebase + 0x2a);
+
+	/* pipe Wrapper usb3 TX swing de-emph margin PREEMPH[7:4], SWING[3:0] */
+	writeb_relaxed(0X67, miphy_phy->pipebase + 0x68);
+	writeb_relaxed(0x0d, miphy_phy->pipebase + 0x69);
+	writeb_relaxed(0X67, miphy_phy->pipebase + 0x6a);
+	writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6b);
+	writeb_relaxed(0X67, miphy_phy->pipebase + 0x6c);
+	writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6d);
+	writeb_relaxed(0X67, miphy_phy->pipebase + 0x6e);
+	writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6f);
+
+	return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init(struct phy *phy)
+{
+	struct miphy28lp_phy *miphy_phy = phy_get_drvdata(phy);
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	int ret;
+
+	mutex_lock(&miphy_dev->miphy_mutex);
+
+	switch (miphy_phy->type) {
+
+	case PHY_TYPE_SATA:
+		ret = miphy28lp_init_sata(miphy_phy);
+		break;
+	case PHY_TYPE_PCIE:
+		ret = miphy28lp_init_pcie(miphy_phy);
+		break;
+	case PHY_TYPE_USB3:
+		ret = miphy28lp_init_usb3(miphy_phy);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	mutex_unlock(&miphy_dev->miphy_mutex);
+
+	return ret;
+}
+
+static int miphy28lp_get_addr(struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	struct device_node *phynode = miphy_phy->phy->dev.of_node;
+	int err;
+
+	if ((miphy_phy->type != PHY_TYPE_SATA) &&
+	    (miphy_phy->type != PHY_TYPE_PCIE) &&
+	    (miphy_phy->type != PHY_TYPE_USB3)) {
+		return -EINVAL;
+	}
+
+	err = miphy28lp_get_one_addr(miphy_dev->dev, phynode,
+			PHY_TYPE_name[miphy_phy->type - PHY_TYPE_SATA],
+			&miphy_phy->base);
+	if (err)
+		return err;
+
+	if ((miphy_phy->type == PHY_TYPE_PCIE) ||
+	    (miphy_phy->type == PHY_TYPE_USB3)) {
+		err = miphy28lp_get_one_addr(miphy_dev->dev, phynode, "pipew",
+					     &miphy_phy->pipebase);
+		if (err)
+			return err;
+	}
+
+	return 0;
+}
+
+static struct phy *miphy28lp_xlate(struct device *dev,
+				   struct of_phandle_args *args)
+{
+	struct miphy28lp_dev *miphy_dev = dev_get_drvdata(dev);
+	struct miphy28lp_phy *miphy_phy = NULL;
+	struct device_node *phynode = args->np;
+	int ret, index = 0;
+
+	if (!of_device_is_available(phynode)) {
+		dev_warn(dev, "Requested PHY is disabled\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	if (args->args_count != 1) {
+		dev_err(dev, "Invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < of_get_child_count(dev->of_node); index++)
+		if (phynode == miphy_dev->phys[index]->phy->dev.of_node) {
+			miphy_phy = miphy_dev->phys[index];
+			break;
+		}
+
+	if (!miphy_phy) {
+		dev_err(dev, "Failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	miphy_phy->type = args->args[0];
+
+	ret = miphy28lp_get_addr(miphy_phy);
+	if (ret < 0)
+		return ERR_PTR(ret);
+
+	return miphy_phy->phy;
+}
+
+static struct phy_ops miphy28lp_ops = {
+	.init = miphy28lp_init,
+};
+
+static int miphy28lp_probe_resets(struct device_node *node,
+				  struct miphy28lp_phy *miphy_phy)
+{
+	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+	int err;
+
+	miphy_phy->miphy_rst = of_reset_control_get(node, "miphy-sw-rst");
+
+	if (IS_ERR(miphy_phy->miphy_rst)) {
+		dev_err(miphy_dev->dev,
+				"miphy soft reset control not defined\n");
+		return PTR_ERR(miphy_phy->miphy_rst);
+	}
+
+	err = reset_control_deassert(miphy_phy->miphy_rst);
+	if (err) {
+		dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+		return err;
+	}
+
+	return 0;
+}
+
+static int miphy28lp_of_probe(struct device_node *np,
+			      struct miphy28lp_phy *miphy_phy)
+{
+	struct resource res;
+
+	miphy_phy->osc_force_ext =
+		of_property_read_bool(np, "st,osc-force-ext");
+
+	miphy_phy->osc_rdy = of_property_read_bool(np, "st,osc-rdy");
+
+	miphy_phy->px_rx_pol_inv =
+		of_property_read_bool(np, "st,px_rx_pol_inv");
+
+	miphy_phy->ssc = of_property_read_bool(np, "st,ssc-on");
+
+	miphy_phy->tx_impedance =
+		of_property_read_bool(np, "st,tx-impedance-comp");
+
+	of_property_read_u32(np, "st,sata-gen", &miphy_phy->sata_gen);
+	if (!miphy_phy->sata_gen)
+		miphy_phy->sata_gen = SATA_GEN1;
+
+	if (!miphy28lp_get_resource_byname(np, "miphy-ctrl-glue", &res))
+		miphy_phy->syscfg_miphy_ctrl = res.start;
+
+	if (!miphy28lp_get_resource_byname(np, "miphy-status-glue", &res))
+		miphy_phy->syscfg_miphy_status = res.start;
+
+	if (!miphy28lp_get_resource_byname(np, "pcie-glue", &res))
+		miphy_phy->syscfg_pci = res.start;
+
+	if (!miphy28lp_get_resource_byname(np, "sata-glue", &res))
+		miphy_phy->syscfg_sata = res.start;
+
+
+	return 0;
+}
+
+static int miphy28lp_probe(struct platform_device *pdev)
+{
+	struct device_node *child, *np = pdev->dev.of_node;
+	struct miphy28lp_dev *miphy_dev;
+	struct phy_provider *provider;
+	struct phy *phy;
+	int chancount, port = 0;
+	int ret;
+
+	miphy_dev = devm_kzalloc(&pdev->dev, sizeof(*miphy_dev), GFP_KERNEL);
+	if (!miphy_dev)
+		return -ENOMEM;
+
+	chancount = of_get_child_count(np);
+	miphy_dev->phys = devm_kzalloc(&pdev->dev, sizeof(phy) * chancount,
+				       GFP_KERNEL);
+	if (!miphy_dev->phys)
+		return -ENOMEM;
+
+	miphy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+	if (IS_ERR(miphy_dev->regmap)) {
+		dev_err(miphy_dev->dev, "No syscfg phandle specified\n");
+		return PTR_ERR(miphy_dev->regmap);
+	}
+
+	miphy_dev->dev = &pdev->dev;
+
+	dev_set_drvdata(&pdev->dev, miphy_dev);
+
+	mutex_init(&miphy_dev->miphy_mutex);
+
+	for_each_child_of_node(np, child) {
+		struct miphy28lp_phy *miphy_phy;
+
+		miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
+					 GFP_KERNEL);
+		if (!miphy_phy)
+			return -ENOMEM;
+
+		miphy_dev->phys[port] = miphy_phy;
+
+		phy = devm_phy_create(&pdev->dev, child, &miphy28lp_ops);
+		if (IS_ERR(phy)) {
+			dev_err(&pdev->dev, "failed to create PHY\n");
+			return PTR_ERR(phy);
+		}
+
+		miphy_dev->phys[port]->phy = phy;
+		miphy_dev->phys[port]->phydev = miphy_dev;
+
+		ret = miphy28lp_of_probe(child, miphy_phy);
+		if (ret)
+			return ret;
+
+		ret = miphy28lp_probe_resets(child, miphy_dev->phys[port]);
+		if (ret)
+			return ret;
+
+		phy_set_drvdata(phy, miphy_dev->phys[port]);
+		port++;
+
+	}
+
+	provider = devm_of_phy_provider_register(&pdev->dev, miphy28lp_xlate);
+	if (IS_ERR(provider))
+		return PTR_ERR(provider);
+
+	return 0;
+}
+
+static const struct of_device_id miphy28lp_of_match[] = {
+	{.compatible = "st,miphy28lp-phy", },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, miphy28lp_of_match);
+
+static struct platform_driver miphy28lp_driver = {
+	.probe = miphy28lp_probe,
+	.driver = {
+		.name = "miphy28lp-phy",
+		.owner = THIS_MODULE,
+		.of_match_table = miphy28lp_of_match,
+	}
+};
+
+module_platform_driver(miphy28lp_driver);
+
+MODULE_AUTHOR("Alexandre Torgue <alexandre.torgue@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics miphy28lp driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c
index 801afaf2d449..6ab43a814ad2 100644
--- a/drivers/phy/phy-miphy365x.c
+++ b/drivers/phy/phy-miphy365x.c
@@ -593,7 +593,7 @@ static int miphy365x_probe(struct platform_device *pdev)
 
 		miphy_dev->phys[port] = miphy_phy;
 
-		phy = devm_phy_create(&pdev->dev, child, &miphy365x_ops, NULL);
+		phy = devm_phy_create(&pdev->dev, child, &miphy365x_ops);
 		if (IS_ERR(phy)) {
 			dev_err(&pdev->dev, "failed to create PHY\n");
 			return PTR_ERR(phy);
@@ -610,10 +610,7 @@ static int miphy365x_probe(struct platform_device *pdev)
 	}
 
 	provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
-	if (IS_ERR(provider))
-		return PTR_ERR(provider);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(provider);
 }
 
 static const struct of_device_id miphy365x_of_match[] = {
diff --git a/drivers/phy/phy-mvebu-sata.c b/drivers/phy/phy-mvebu-sata.c
index d395558cb12e..03b94f92e6f1 100644
--- a/drivers/phy/phy-mvebu-sata.c
+++ b/drivers/phy/phy-mvebu-sata.c
@@ -101,7 +101,7 @@ static int phy_mvebu_sata_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->clk))
 		return PTR_ERR(priv->clk);
 
-	phy = devm_phy_create(&pdev->dev, NULL, &phy_mvebu_sata_ops, NULL);
+	phy = devm_phy_create(&pdev->dev, NULL, &phy_mvebu_sata_ops);
 	if (IS_ERR(phy))
 		return PTR_ERR(phy);
 
diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c
index 08f2da270837..4e489a8850e5 100644
--- a/drivers/phy/phy-omap-usb2.c
+++ b/drivers/phy/phy-omap-usb2.c
@@ -256,7 +256,7 @@ static int omap_usb2_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, phy);
 	pm_runtime_enable(phy->dev);
 
-	generic_phy = devm_phy_create(phy->dev, NULL, &ops, NULL);
+	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
 	if (IS_ERR(generic_phy)) {
 		pm_runtime_disable(phy->dev);
 		return PTR_ERR(generic_phy);
diff --git a/drivers/phy/phy-qcom-apq8064-sata.c b/drivers/phy/phy-qcom-apq8064-sata.c
index 7b3ddfb65898..4b243f7a10e4 100644
--- a/drivers/phy/phy-qcom-apq8064-sata.c
+++ b/drivers/phy/phy-qcom-apq8064-sata.c
@@ -228,8 +228,7 @@ static int qcom_apq8064_sata_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(phy->mmio))
 		return PTR_ERR(phy->mmio);
 
-	generic_phy = devm_phy_create(dev, NULL, &qcom_apq8064_sata_phy_ops,
-				      NULL);
+	generic_phy = devm_phy_create(dev, NULL, &qcom_apq8064_sata_phy_ops);
 	if (IS_ERR(generic_phy)) {
 		dev_err(dev, "%s: failed to create phy\n", __func__);
 		return PTR_ERR(generic_phy);
diff --git a/drivers/phy/phy-qcom-ipq806x-sata.c b/drivers/phy/phy-qcom-ipq806x-sata.c
index 759b0bf5b6b3..6f2fe2627916 100644
--- a/drivers/phy/phy-qcom-ipq806x-sata.c
+++ b/drivers/phy/phy-qcom-ipq806x-sata.c
@@ -150,8 +150,7 @@ static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(phy->mmio))
 		return PTR_ERR(phy->mmio);
 
-	generic_phy = devm_phy_create(dev, NULL, &qcom_ipq806x_sata_phy_ops,
-				      NULL);
+	generic_phy = devm_phy_create(dev, NULL, &qcom_ipq806x_sata_phy_ops);
 	if (IS_ERR(generic_phy)) {
 		dev_err(dev, "%s: failed to create phy\n", __func__);
 		return PTR_ERR(generic_phy);
diff --git a/drivers/phy/phy-rcar-gen2.c b/drivers/phy/phy-rcar-gen2.c
index 2793af17799f..778276aba3aa 100644
--- a/drivers/phy/phy-rcar-gen2.c
+++ b/drivers/phy/phy-rcar-gen2.c
@@ -304,7 +304,7 @@ static int rcar_gen2_phy_probe(struct platform_device *pdev)
 			phy->select_value = select_value[channel_num][n];
 
 			phy->phy = devm_phy_create(dev, NULL,
-						   &rcar_gen2_phy_ops, NULL);
+						   &rcar_gen2_phy_ops);
 			if (IS_ERR(phy->phy)) {
 				dev_err(dev, "Failed to create PHY\n");
 				return PTR_ERR(phy->phy);
diff --git a/drivers/phy/phy-samsung-usb2.c b/drivers/phy/phy-samsung-usb2.c
index 908949dfb4db..4a12f66b7fb5 100644
--- a/drivers/phy/phy-samsung-usb2.c
+++ b/drivers/phy/phy-samsung-usb2.c
@@ -202,8 +202,7 @@ static int samsung_usb2_phy_probe(struct platform_device *pdev)
 		struct samsung_usb2_phy_instance *p = &drv->instances[i];
 
 		dev_dbg(dev, "Creating phy \"%s\"\n", label);
-		p->phy = devm_phy_create(dev, NULL, &samsung_usb2_phy_ops,
-					 NULL);
+		p->phy = devm_phy_create(dev, NULL, &samsung_usb2_phy_ops);
 		if (IS_ERR(p->phy)) {
 			dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n",
 				label);
diff --git a/drivers/phy/phy-spear1310-miphy.c b/drivers/phy/phy-spear1310-miphy.c
index 5f4c586ee951..9f47fae7eecb 100644
--- a/drivers/phy/phy-spear1310-miphy.c
+++ b/drivers/phy/phy-spear1310-miphy.c
@@ -227,7 +227,7 @@ static int spear1310_miphy_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	priv->phy = devm_phy_create(dev, NULL, &spear1310_miphy_ops, NULL);
+	priv->phy = devm_phy_create(dev, NULL, &spear1310_miphy_ops);
 	if (IS_ERR(priv->phy)) {
 		dev_err(dev, "failed to create SATA PCIe PHY\n");
 		return PTR_ERR(priv->phy);
diff --git a/drivers/phy/phy-spear1340-miphy.c b/drivers/phy/phy-spear1340-miphy.c
index 1ecd0945bad3..e42bc200275f 100644
--- a/drivers/phy/phy-spear1340-miphy.c
+++ b/drivers/phy/phy-spear1340-miphy.c
@@ -259,7 +259,7 @@ static int spear1340_miphy_probe(struct platform_device *pdev)
 		return PTR_ERR(priv->misc);
 	}
 
-	priv->phy = devm_phy_create(dev, NULL, &spear1340_miphy_ops, NULL);
+	priv->phy = devm_phy_create(dev, NULL, &spear1340_miphy_ops);
 	if (IS_ERR(priv->phy)) {
 		dev_err(dev, "failed to create SATA PCIe PHY\n");
 		return PTR_ERR(priv->phy);
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/phy-stih407-usb.c
index 42428d4181ea..74f0fab3cd8a 100644
--- a/drivers/phy/phy-stih407-usb.c
+++ b/drivers/phy/phy-stih407-usb.c
@@ -137,7 +137,7 @@ static int stih407_usb2_picophy_probe(struct platform_device *pdev)
 	}
 	phy_dev->param = res->start;
 
-	phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data, NULL);
+	phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data);
 	if (IS_ERR(phy)) {
 		dev_err(dev, "failed to create Display Port PHY\n");
 		return PTR_ERR(phy);
diff --git a/drivers/phy/phy-stih41x-usb.c b/drivers/phy/phy-stih41x-usb.c
index 9f16cb8e01f4..a603801293ff 100644
--- a/drivers/phy/phy-stih41x-usb.c
+++ b/drivers/phy/phy-stih41x-usb.c
@@ -148,7 +148,7 @@ static int stih41x_usb_phy_probe(struct platform_device *pdev)
 		return PTR_ERR(phy_dev->clk);
 	}
 
-	phy = devm_phy_create(dev, NULL, &stih41x_usb_phy_ops, NULL);
+	phy = devm_phy_create(dev, NULL, &stih41x_usb_phy_ops);
 
 	if (IS_ERR(phy)) {
 		dev_err(dev, "failed to create phy\n");
@@ -160,10 +160,7 @@ static int stih41x_usb_phy_probe(struct platform_device *pdev)
 	phy_set_drvdata(phy, phy_dev);
 
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
-	if (IS_ERR(phy_provider))
-		return PTR_ERR(phy_provider);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
 static const struct of_device_id stih41x_usb_phy_of_match[] = {
diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c
index 0baf5efc8a40..fb02a67c9181 100644
--- a/drivers/phy/phy-sun4i-usb.c
+++ b/drivers/phy/phy-sun4i-usb.c
@@ -157,6 +157,10 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
+	/* Enable USB 45 Ohm resistor calibration */
+	if (phy->index == 0)
+		sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
+
 	/* Adjust PHY's magnitude and rate */
 	sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
 
@@ -213,7 +217,7 @@ static struct phy *sun4i_usb_phy_xlate(struct device *dev,
 {
 	struct sun4i_usb_phy_data *data = dev_get_drvdata(dev);
 
-	if (WARN_ON(args->args[0] == 0 || args->args[0] >= data->num_phys))
+	if (args->args[0] >= data->num_phys)
 		return ERR_PTR(-ENODEV);
 
 	return data->phys[args->args[0]].phy;
@@ -255,8 +259,7 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(data->base))
 		return PTR_ERR(data->base);
 
-	/* Skip 0, 0 is the phy for otg which is not yet supported. */
-	for (i = 1; i < data->num_phys; i++) {
+	for (i = 0; i < data->num_phys; i++) {
 		struct sun4i_usb_phy *phy = data->phys + i;
 		char name[16];
 
@@ -295,7 +298,7 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 				return PTR_ERR(phy->pmu);
 		}
 
-		phy->phy = devm_phy_create(dev, NULL, &sun4i_usb_phy_ops, NULL);
+		phy->phy = devm_phy_create(dev, NULL, &sun4i_usb_phy_ops);
 		if (IS_ERR(phy->phy)) {
 			dev_err(dev, "failed to create PHY %d\n", i);
 			return PTR_ERR(phy->phy);
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index ab1e22d9a1e8..c297b7a10d30 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -399,7 +399,7 @@ static int ti_pipe3_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, phy);
 	pm_runtime_enable(phy->dev);
 
-	generic_phy = devm_phy_create(phy->dev, NULL, &ops, NULL);
+	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
 	if (IS_ERR(generic_phy))
 		return PTR_ERR(generic_phy);
 
diff --git a/drivers/phy/phy-twl4030-usb.c b/drivers/phy/phy-twl4030-usb.c
index e2698d29f436..8e87f54671f3 100644
--- a/drivers/phy/phy-twl4030-usb.c
+++ b/drivers/phy/phy-twl4030-usb.c
@@ -644,7 +644,6 @@ static int twl4030_usb_probe(struct platform_device *pdev)
 	struct usb_otg		*otg;
 	struct device_node	*np = pdev->dev.of_node;
 	struct phy_provider	*phy_provider;
-	struct phy_init_data	*init_data = NULL;
 
 	twl = devm_kzalloc(&pdev->dev, sizeof(*twl), GFP_KERNEL);
 	if (!twl)
@@ -655,7 +654,6 @@ static int twl4030_usb_probe(struct platform_device *pdev)
 				(enum twl4030_usb_mode *)&twl->usb_mode);
 	else if (pdata) {
 		twl->usb_mode = pdata->usb_mode;
-		init_data = pdata->init_data;
 	} else {
 		dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
 		return -EINVAL;
@@ -680,7 +678,7 @@ static int twl4030_usb_probe(struct platform_device *pdev)
 	otg->set_host		= twl4030_set_host;
 	otg->set_peripheral	= twl4030_set_peripheral;
 
-	phy = devm_phy_create(twl->dev, NULL, &ops, init_data);
+	phy = devm_phy_create(twl->dev, NULL, &ops);
 	if (IS_ERR(phy)) {
 		dev_dbg(&pdev->dev, "Failed to create PHY\n");
 		return PTR_ERR(phy);
@@ -733,6 +731,11 @@ static int twl4030_usb_probe(struct platform_device *pdev)
 		return status;
 	}
 
+	if (pdata)
+		err = phy_create_lookup(phy, "usb", "musb-hdrc.0");
+	if (err)
+		return err;
+
 	pm_runtime_mark_last_busy(&pdev->dev);
 	pm_runtime_put_autosuspend(twl->dev);
 
diff --git a/drivers/phy/phy-xgene.c b/drivers/phy/phy-xgene.c
index f8a51b16ade8..29214a36ea28 100644
--- a/drivers/phy/phy-xgene.c
+++ b/drivers/phy/phy-xgene.c
@@ -1707,7 +1707,7 @@ static int xgene_phy_probe(struct platform_device *pdev)
 	ctx->dev = &pdev->dev;
 	platform_set_drvdata(pdev, ctx);
 
-	ctx->phy = devm_phy_create(ctx->dev, NULL, &xgene_phy_ops, NULL);
+	ctx->phy = devm_phy_create(ctx->dev, NULL, &xgene_phy_ops);
 	if (IS_ERR(ctx->phy)) {
 		dev_dbg(&pdev->dev, "Failed to create PHY\n");
 		rc = PTR_ERR(ctx->phy);