Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Support offloading wireless authentication to userspace via
    NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.

 2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
    Setup and cleanup of namespaces now all run asynchronously and thus
    performance is significantly increased.

 3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
    Streiff.

 4) Support zerocopy on RDS sockets, from Sowmini Varadhan.

 5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
    Borkmann.

 6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
    Chevallier.

 7) Support grafting of child qdiscs in mlxsw driver, from Nogah
    Frankel.

 8) Add packet forwarding tests to selftests, from Ido Schimmel.

 9) Deal with sub-optimal GSO packets better in BBR congestion control,
    from Eric Dumazet.

10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.

11) Add path MTU tests to selftests, from Stefano Brivio.

12) Various bits of IPSEC offloading support for mlx5, from Aviad
    Yehezkel, Yossi Kuperman, and Saeed Mahameed.

13) Support RSS spreading on ntuple filters in SFC driver, from Edward
    Cree.

14) Lots of sockmap work from John Fastabend. Applications can use eBPF
    to filter sendmsg and sendpage operations.

15) In-kernel receive TLS support, from Dave Watson.

16) Add XDP support to ixgbevf, this is significant because it should
    allow optimized XDP usage in various cloud environments. From Tony
    Nguyen.

17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
    Venkataramanan et al.

18) IP fragmentation match offload support in nfp driver, from Pieter
    Jansen van Vuuren.

19) Support XDP redirect in i40e driver, from Björn Töpel.

20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
    tracepoints in their raw form, from Alexei Starovoitov.

21) Lots of striding RQ improvements to mlx5 driver with many
    performance improvements, from Tariq Toukan.

22) Use rhashtable for inet frag reassembly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
  net: mvneta: improve suspend/resume
  net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
  ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
  net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
  net: bgmac: Correctly annotate register space
  route: check sysctl_fib_multipath_use_neigh earlier than hash
  fix typo in command value in drivers/net/phy/mdio-bitbang.
  sky2: Increase D3 delay to sky2 stops working after suspend
  net/mlx5e: Set EQE based as default TX interrupt moderation mode
  ibmvnic: Disable irqs before exiting reset from closed state
  net: sched: do not emit messages while holding spinlock
  vlan: also check phy_driver ts_info for vlan's real device
  Bluetooth: Mark expected switch fall-throughs
  Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
  Bluetooth: btrsi: remove unused including <linux/version.h>
  Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
  sh_eth: kill useless check in __sh_eth_get_regs()
  sh_eth: add sh_eth_cpu_data::no_xdfar flag
  ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
  ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
  ...

1 files changed, 282 insertions, 146 deletions

diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index 357d6051281f..12bd937861e7 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*******************************************************************************
  *
  * Intel Ethernet Controller XL710 Family Linux Virtual Function Driver
@@ -196,7 +197,7 @@ void i40evf_detect_recover_hung(struct i40e_vsi *vsi)
 			 */
 			smp_rmb();
 			tx_ring->tx_stats.prev_pkt_ctr =
-			  i40evf_get_tx_pending(tx_ring, false) ? packets : -1;
+			  i40evf_get_tx_pending(tx_ring, true) ? packets : -1;
 		}
 	}
 }
@@ -392,99 +393,241 @@ void i40evf_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
 	     val);
 }
 
+static inline bool i40e_container_is_rx(struct i40e_q_vector *q_vector,
+					struct i40e_ring_container *rc)
+{
+	return &q_vector->rx == rc;
+}
+
+static inline unsigned int i40e_itr_divisor(struct i40e_q_vector *q_vector)
+{
+	unsigned int divisor;
+
+	switch (q_vector->adapter->link_speed) {
+	case I40E_LINK_SPEED_40GB:
+		divisor = I40E_ITR_ADAPTIVE_MIN_INC * 1024;
+		break;
+	case I40E_LINK_SPEED_25GB:
+	case I40E_LINK_SPEED_20GB:
+		divisor = I40E_ITR_ADAPTIVE_MIN_INC * 512;
+		break;
+	default:
+	case I40E_LINK_SPEED_10GB:
+		divisor = I40E_ITR_ADAPTIVE_MIN_INC * 256;
+		break;
+	case I40E_LINK_SPEED_1GB:
+	case I40E_LINK_SPEED_100MB:
+		divisor = I40E_ITR_ADAPTIVE_MIN_INC * 32;
+		break;
+	}
+
+	return divisor;
+}
+
 /**
- * i40e_set_new_dynamic_itr - Find new ITR level
+ * i40e_update_itr - update the dynamic ITR value based on statistics
+ * @q_vector: structure containing interrupt and ring information
  * @rc: structure containing ring performance data
  *
- * Returns true if ITR changed, false if not
- *
- * Stores a new ITR value based on packets and byte counts during
- * the last interrupt.  The advantage of per interrupt computation
- * is faster updates and more accurate ITR for the current traffic
- * pattern.  Constants in this function were computed based on
- * theoretical maximum wire speed and thresholds were set based on
- * testing data as well as attempting to minimize response time
+ * Stores a new ITR value based on packets and byte
+ * counts during the last interrupt.  The advantage of per interrupt
+ * computation is faster updates and more accurate ITR for the current
+ * traffic pattern.  Constants in this function were computed
+ * based on theoretical maximum wire speed and thresholds were set based
+ * on testing data as well as attempting to minimize response time
  * while increasing bulk throughput.
  **/
-static bool i40e_set_new_dynamic_itr(struct i40e_ring_container *rc)
+static void i40e_update_itr(struct i40e_q_vector *q_vector,
+			    struct i40e_ring_container *rc)
 {
-	enum i40e_latency_range new_latency_range = rc->latency_range;
-	u32 new_itr = rc->itr;
-	int bytes_per_usec;
-	unsigned int usecs, estimated_usecs;
+	unsigned int avg_wire_size, packets, bytes, itr;
+	unsigned long next_update = jiffies;
 
-	if (rc->total_packets == 0 || !rc->itr)
-		return false;
+	/* If we don't have any rings just leave ourselves set for maximum
+	 * possible latency so we take ourselves out of the equation.
+	 */
+	if (!rc->ring || !ITR_IS_DYNAMIC(rc->ring->itr_setting))
+		return;
+
+	/* For Rx we want to push the delay up and default to low latency.
+	 * for Tx we want to pull the delay down and default to high latency.
+	 */
+	itr = i40e_container_is_rx(q_vector, rc) ?
+	      I40E_ITR_ADAPTIVE_MIN_USECS | I40E_ITR_ADAPTIVE_LATENCY :
+	      I40E_ITR_ADAPTIVE_MAX_USECS | I40E_ITR_ADAPTIVE_LATENCY;
+
+	/* If we didn't update within up to 1 - 2 jiffies we can assume
+	 * that either packets are coming in so slow there hasn't been
+	 * any work, or that there is so much work that NAPI is dealing
+	 * with interrupt moderation and we don't need to do anything.
+	 */
+	if (time_after(next_update, rc->next_update))
+		goto clear_counts;
+
+	/* If itr_countdown is set it means we programmed an ITR within
+	 * the last 4 interrupt cycles. This has a side effect of us
+	 * potentially firing an early interrupt. In order to work around
+	 * this we need to throw out any data received for a few
+	 * interrupts following the update.
+	 */
+	if (q_vector->itr_countdown) {
+		itr = rc->target_itr;
+		goto clear_counts;
+	}
+
+	packets = rc->total_packets;
+	bytes = rc->total_bytes;
 
-	usecs = (rc->itr << 1) * ITR_COUNTDOWN_START;
-	bytes_per_usec = rc->total_bytes / usecs;
+	if (i40e_container_is_rx(q_vector, rc)) {
+		/* If Rx there are 1 to 4 packets and bytes are less than
+		 * 9000 assume insufficient data to use bulk rate limiting
+		 * approach unless Tx is already in bulk rate limiting. We
+		 * are likely latency driven.
+		 */
+		if (packets && packets < 4 && bytes < 9000 &&
+		    (q_vector->tx.target_itr & I40E_ITR_ADAPTIVE_LATENCY)) {
+			itr = I40E_ITR_ADAPTIVE_LATENCY;
+			goto adjust_by_size;
+		}
+	} else if (packets < 4) {
+		/* If we have Tx and Rx ITR maxed and Tx ITR is running in
+		 * bulk mode and we are receiving 4 or fewer packets just
+		 * reset the ITR_ADAPTIVE_LATENCY bit for latency mode so
+		 * that the Rx can relax.
+		 */
+		if (rc->target_itr == I40E_ITR_ADAPTIVE_MAX_USECS &&
+		    (q_vector->rx.target_itr & I40E_ITR_MASK) ==
+		     I40E_ITR_ADAPTIVE_MAX_USECS)
+			goto clear_counts;
+	} else if (packets > 32) {
+		/* If we have processed over 32 packets in a single interrupt
+		 * for Tx assume we need to switch over to "bulk" mode.
+		 */
+		rc->target_itr &= ~I40E_ITR_ADAPTIVE_LATENCY;
+	}
 
-	/* The calculations in this algorithm depend on interrupts actually
-	 * firing at the ITR rate. This may not happen if the packet rate is
-	 * really low, or if we've been napi polling. Check to make sure
-	 * that's not the case before we continue.
+	/* We have no packets to actually measure against. This means
+	 * either one of the other queues on this vector is active or
+	 * we are a Tx queue doing TSO with too high of an interrupt rate.
+	 *
+	 * Between 4 and 56 we can assume that our current interrupt delay
+	 * is only slightly too low. As such we should increase it by a small
+	 * fixed amount.
 	 */
-	estimated_usecs = jiffies_to_usecs(jiffies - rc->last_itr_update);
-	if (estimated_usecs > usecs) {
-		new_latency_range = I40E_LOW_LATENCY;
-		goto reset_latency;
+	if (packets < 56) {
+		itr = rc->target_itr + I40E_ITR_ADAPTIVE_MIN_INC;
+		if ((itr & I40E_ITR_MASK) > I40E_ITR_ADAPTIVE_MAX_USECS) {
+			itr &= I40E_ITR_ADAPTIVE_LATENCY;
+			itr += I40E_ITR_ADAPTIVE_MAX_USECS;
+		}
+		goto clear_counts;
+	}
+
+	if (packets <= 256) {
+		itr = min(q_vector->tx.current_itr, q_vector->rx.current_itr);
+		itr &= I40E_ITR_MASK;
+
+		/* Between 56 and 112 is our "goldilocks" zone where we are
+		 * working out "just right". Just report that our current
+		 * ITR is good for us.
+		 */
+		if (packets <= 112)
+			goto clear_counts;
+
+		/* If packet count is 128 or greater we are likely looking
+		 * at a slight overrun of the delay we want. Try halving
+		 * our delay to see if that will cut the number of packets
+		 * in half per interrupt.
+		 */
+		itr /= 2;
+		itr &= I40E_ITR_MASK;
+		if (itr < I40E_ITR_ADAPTIVE_MIN_USECS)
+			itr = I40E_ITR_ADAPTIVE_MIN_USECS;
+
+		goto clear_counts;
 	}
 
-	/* simple throttlerate management
-	 *   0-10MB/s   lowest (50000 ints/s)
-	 *  10-20MB/s   low    (20000 ints/s)
-	 *  20-1249MB/s bulk   (18000 ints/s)
+	/* The paths below assume we are dealing with a bulk ITR since
+	 * number of packets is greater than 256. We are just going to have
+	 * to compute a value and try to bring the count under control,
+	 * though for smaller packet sizes there isn't much we can do as
+	 * NAPI polling will likely be kicking in sooner rather than later.
+	 */
+	itr = I40E_ITR_ADAPTIVE_BULK;
+
+adjust_by_size:
+	/* If packet counts are 256 or greater we can assume we have a gross
+	 * overestimation of what the rate should be. Instead of trying to fine
+	 * tune it just use the formula below to try and dial in an exact value
+	 * give the current packet size of the frame.
+	 */
+	avg_wire_size = bytes / packets;
+
+	/* The following is a crude approximation of:
+	 *  wmem_default / (size + overhead) = desired_pkts_per_int
+	 *  rate / bits_per_byte / (size + ethernet overhead) = pkt_rate
+	 *  (desired_pkt_rate / pkt_rate) * usecs_per_sec = ITR value
 	 *
-	 * The math works out because the divisor is in 10^(-6) which
-	 * turns the bytes/us input value into MB/s values, but
-	 * make sure to use usecs, as the register values written
-	 * are in 2 usec increments in the ITR registers, and make sure
-	 * to use the smoothed values that the countdown timer gives us.
+	 * Assuming wmem_default is 212992 and overhead is 640 bytes per
+	 * packet, (256 skb, 64 headroom, 320 shared info), we can reduce the
+	 * formula down to
+	 *
+	 *  (170 * (size + 24)) / (size + 640) = ITR
+	 *
+	 * We first do some math on the packet size and then finally bitshift
+	 * by 8 after rounding up. We also have to account for PCIe link speed
+	 * difference as ITR scales based on this.
 	 */
-	switch (new_latency_range) {
-	case I40E_LOWEST_LATENCY:
-		if (bytes_per_usec > 10)
-			new_latency_range = I40E_LOW_LATENCY;
-		break;
-	case I40E_LOW_LATENCY:
-		if (bytes_per_usec > 20)
-			new_latency_range = I40E_BULK_LATENCY;
-		else if (bytes_per_usec <= 10)
-			new_latency_range = I40E_LOWEST_LATENCY;
-		break;
-	case I40E_BULK_LATENCY:
-	default:
-		if (bytes_per_usec <= 20)
-			new_latency_range = I40E_LOW_LATENCY;
-		break;
+	if (avg_wire_size <= 60) {
+		/* Start at 250k ints/sec */
+		avg_wire_size = 4096;
+	} else if (avg_wire_size <= 380) {
+		/* 250K ints/sec to 60K ints/sec */
+		avg_wire_size *= 40;
+		avg_wire_size += 1696;
+	} else if (avg_wire_size <= 1084) {
+		/* 60K ints/sec to 36K ints/sec */
+		avg_wire_size *= 15;
+		avg_wire_size += 11452;
+	} else if (avg_wire_size <= 1980) {
+		/* 36K ints/sec to 30K ints/sec */
+		avg_wire_size *= 5;
+		avg_wire_size += 22420;
+	} else {
+		/* plateau at a limit of 30K ints/sec */
+		avg_wire_size = 32256;
 	}
 
-reset_latency:
-	rc->latency_range = new_latency_range;
+	/* If we are in low latency mode halve our delay which doubles the
+	 * rate to somewhere between 100K to 16K ints/sec
+	 */
+	if (itr & I40E_ITR_ADAPTIVE_LATENCY)
+		avg_wire_size /= 2;
 
-	switch (new_latency_range) {
-	case I40E_LOWEST_LATENCY:
-		new_itr = I40E_ITR_50K;
-		break;
-	case I40E_LOW_LATENCY:
-		new_itr = I40E_ITR_20K;
-		break;
-	case I40E_BULK_LATENCY:
-		new_itr = I40E_ITR_18K;
-		break;
-	default:
-		break;
+	/* Resultant value is 256 times larger than it needs to be. This
+	 * gives us room to adjust the value as needed to either increase
+	 * or decrease the value based on link speeds of 10G, 2.5G, 1G, etc.
+	 *
+	 * Use addition as we have already recorded the new latency flag
+	 * for the ITR value.
+	 */
+	itr += DIV_ROUND_UP(avg_wire_size, i40e_itr_divisor(q_vector)) *
+	       I40E_ITR_ADAPTIVE_MIN_INC;
+
+	if ((itr & I40E_ITR_MASK) > I40E_ITR_ADAPTIVE_MAX_USECS) {
+		itr &= I40E_ITR_ADAPTIVE_LATENCY;
+		itr += I40E_ITR_ADAPTIVE_MAX_USECS;
 	}
 
+clear_counts:
+	/* write back value */
+	rc->target_itr = itr;
+
+	/* next update should occur within next jiffy */
+	rc->next_update = next_update + 1;
+
 	rc->total_bytes = 0;
 	rc->total_packets = 0;
-	rc->last_itr_update = jiffies;
-
-	if (new_itr != rc->itr) {
-		rc->itr = new_itr;
-		return true;
-	}
-	return false;
 }
 
 /**
@@ -1273,7 +1416,7 @@ static struct sk_buff *i40e_build_skb(struct i40e_ring *rx_ring,
  * @rx_buffer: rx buffer to pull data from
  *
  * This function will clean up the contents of the rx_buffer.  It will
- * either recycle the bufer or unmap it and free the associated resources.
+ * either recycle the buffer or unmap it and free the associated resources.
  */
 static void i40e_put_rx_buffer(struct i40e_ring *rx_ring,
 			       struct i40e_rx_buffer *rx_buffer)
@@ -1457,33 +1600,45 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
 	return failure ? budget : (int)total_rx_packets;
 }
 
-static u32 i40e_buildreg_itr(const int type, const u16 itr)
+static inline u32 i40e_buildreg_itr(const int type, u16 itr)
 {
 	u32 val;
 
+	/* We don't bother with setting the CLEARPBA bit as the data sheet
+	 * points out doing so is "meaningless since it was already
+	 * auto-cleared". The auto-clearing happens when the interrupt is
+	 * asserted.
+	 *
+	 * Hardware errata 28 for also indicates that writing to a
+	 * xxINT_DYN_CTLx CSR with INTENA_MSK (bit 31) set to 0 will clear
+	 * an event in the PBA anyway so we need to rely on the automask
+	 * to hold pending events for us until the interrupt is re-enabled
+	 *
+	 * The itr value is reported in microseconds, and the register
+	 * value is recorded in 2 microsecond units. For this reason we
+	 * only need to shift by the interval shift - 1 instead of the
+	 * full value.
+	 */
+	itr &= I40E_ITR_MASK;
+
 	val = I40E_VFINT_DYN_CTLN1_INTENA_MASK |
-	      I40E_VFINT_DYN_CTLN1_CLEARPBA_MASK |
 	      (type << I40E_VFINT_DYN_CTLN1_ITR_INDX_SHIFT) |
-	      (itr << I40E_VFINT_DYN_CTLN1_INTERVAL_SHIFT);
+	      (itr << (I40E_VFINT_DYN_CTLN1_INTERVAL_SHIFT - 1));
 
 	return val;
 }
 
 /* a small macro to shorten up some long lines */
 #define INTREG I40E_VFINT_DYN_CTLN1
-static inline int get_rx_itr(struct i40e_vsi *vsi, int idx)
-{
-	struct i40evf_adapter *adapter = vsi->back;
 
-	return adapter->rx_rings[idx].rx_itr_setting;
-}
-
-static inline int get_tx_itr(struct i40e_vsi *vsi, int idx)
-{
-	struct i40evf_adapter *adapter = vsi->back;
-
-	return adapter->tx_rings[idx].tx_itr_setting;
-}
+/* The act of updating the ITR will cause it to immediately trigger. In order
+ * to prevent this from throwing off adaptive update statistics we defer the
+ * update so that it can only happen so often. So after either Tx or Rx are
+ * updated we make the adaptive scheme wait until either the ITR completely
+ * expires via the next_update expiration or we have been through at least
+ * 3 interrupts.
+ */
+#define ITR_COUNTDOWN_START 3
 
 /**
  * i40e_update_enable_itr - Update itr and re-enable MSIX interrupt
@@ -1495,70 +1650,51 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi,
 					  struct i40e_q_vector *q_vector)
 {
 	struct i40e_hw *hw = &vsi->back->hw;
-	bool rx = false, tx = false;
-	u32 rxval, txval;
-	int idx = q_vector->v_idx;
-	int rx_itr_setting, tx_itr_setting;
-
-	/* avoid dynamic calculation if in countdown mode OR if
-	 * all dynamic is disabled
-	 */
-	rxval = txval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
-
-	rx_itr_setting = get_rx_itr(vsi, idx);
-	tx_itr_setting = get_tx_itr(vsi, idx);
+	u32 intval;
 
-	if (q_vector->itr_countdown > 0 ||
-	    (!ITR_IS_DYNAMIC(rx_itr_setting) &&
-	     !ITR_IS_DYNAMIC(tx_itr_setting))) {
-		goto enable_int;
-	}
-
-	if (ITR_IS_DYNAMIC(rx_itr_setting)) {
-		rx = i40e_set_new_dynamic_itr(&q_vector->rx);
-		rxval = i40e_buildreg_itr(I40E_RX_ITR, q_vector->rx.itr);
-	}
+	/* These will do nothing if dynamic updates are not enabled */
+	i40e_update_itr(q_vector, &q_vector->tx);
+	i40e_update_itr(q_vector, &q_vector->rx);
 
-	if (ITR_IS_DYNAMIC(tx_itr_setting)) {
-		tx = i40e_set_new_dynamic_itr(&q_vector->tx);
-		txval = i40e_buildreg_itr(I40E_TX_ITR, q_vector->tx.itr);
-	}
-
-	if (rx || tx) {
-		/* get the higher of the two ITR adjustments and
-		 * use the same value for both ITR registers
-		 * when in adaptive mode (Rx and/or Tx)
-		 */
-		u16 itr = max(q_vector->tx.itr, q_vector->rx.itr);
-
-		q_vector->tx.itr = q_vector->rx.itr = itr;
-		txval = i40e_buildreg_itr(I40E_TX_ITR, itr);
-		tx = true;
-		rxval = i40e_buildreg_itr(I40E_RX_ITR, itr);
-		rx = true;
-	}
-
-	/* only need to enable the interrupt once, but need
-	 * to possibly update both ITR values
+	/* This block of logic allows us to get away with only updating
+	 * one ITR value with each interrupt. The idea is to perform a
+	 * pseudo-lazy update with the following criteria.
+	 *
+	 * 1. Rx is given higher priority than Tx if both are in same state
+	 * 2. If we must reduce an ITR that is given highest priority.
+	 * 3. We then give priority to increasing ITR based on amount.
 	 */
-	if (rx) {
-		/* set the INTENA_MSK_MASK so that this first write
-		 * won't actually enable the interrupt, instead just
-		 * updating the ITR (it's bit 31 PF and VF)
+	if (q_vector->rx.target_itr < q_vector->rx.current_itr) {
+		/* Rx ITR needs to be reduced, this is highest priority */
+		intval = i40e_buildreg_itr(I40E_RX_ITR,
+					   q_vector->rx.target_itr);
+		q_vector->rx.current_itr = q_vector->rx.target_itr;
+		q_vector->itr_countdown = ITR_COUNTDOWN_START;
+	} else if ((q_vector->tx.target_itr < q_vector->tx.current_itr) ||
+		   ((q_vector->rx.target_itr - q_vector->rx.current_itr) <
+		    (q_vector->tx.target_itr - q_vector->tx.current_itr))) {
+		/* Tx ITR needs to be reduced, this is second priority
+		 * Tx ITR needs to be increased more than Rx, fourth priority
 		 */
-		rxval |= BIT(31);
-		/* don't check _DOWN because interrupt isn't being enabled */
-		wr32(hw, INTREG(q_vector->reg_idx), rxval);
+		intval = i40e_buildreg_itr(I40E_TX_ITR,
+					   q_vector->tx.target_itr);
+		q_vector->tx.current_itr = q_vector->tx.target_itr;
+		q_vector->itr_countdown = ITR_COUNTDOWN_START;
+	} else if (q_vector->rx.current_itr != q_vector->rx.target_itr) {
+		/* Rx ITR needs to be increased, third priority */
+		intval = i40e_buildreg_itr(I40E_RX_ITR,
+					   q_vector->rx.target_itr);
+		q_vector->rx.current_itr = q_vector->rx.target_itr;
+		q_vector->itr_countdown = ITR_COUNTDOWN_START;
+	} else {
+		/* No ITR update, lowest priority */
+		intval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
+		if (q_vector->itr_countdown)
+			q_vector->itr_countdown--;
 	}
 
-enable_int:
 	if (!test_bit(__I40E_VSI_DOWN, vsi->state))
-		wr32(hw, INTREG(q_vector->reg_idx), txval);
-
-	if (q_vector->itr_countdown)
-		q_vector->itr_countdown--;
-	else
-		q_vector->itr_countdown = ITR_COUNTDOWN_START;
+		wr32(hw, INTREG(q_vector->reg_idx), intval);
 }
 
 /**