Blackfin: bfin_serial.h: unify heavily duplicated serial code

Each Blackfin port has been duplicating UART structures and defines when
there really is no need for it.  So start a new bfin_serial.h header to
unify all these pieces and give ourselves a fresh start.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 263 insertions, 0 deletions

diff --git a/arch/blackfin/include/asm/bfin_serial.h b/arch/blackfin/include/asm/bfin_serial.h
new file mode 100644
index 000000000000..e9510eab5e22
--- /dev/null
+++ b/arch/blackfin/include/asm/bfin_serial.h
@@ -0,0 +1,263 @@
+/*
+ * bfin_serial.h - Blackfin UART/Serial definitions
+ *
+ * Copyright 2006-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __BFIN_ASM_SERIAL_H__
+#define __BFIN_ASM_SERIAL_H__
+
+#include <linux/serial_core.h>
+#include <mach/anomaly.h>
+#include <mach/bfin_serial.h>
+
+struct circ_buf;
+struct timer_list;
+struct work_struct;
+
+struct bfin_serial_port {
+	struct uart_port port;
+	unsigned int old_status;
+	int status_irq;
+#ifndef BFIN_UART_BF54X_STYLE
+	unsigned int lsr;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	int tx_done;
+	int tx_count;
+	struct circ_buf rx_dma_buf;
+	struct timer_list rx_dma_timer;
+	int rx_dma_nrows;
+	unsigned int tx_dma_channel;
+	unsigned int rx_dma_channel;
+	struct work_struct tx_dma_workqueue;
+#elif ANOMALY_05000363
+	unsigned int anomaly_threshold;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+	int scts;
+#endif
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+	int cts_pin;
+	int rts_pin;
+#endif
+};
+
+/* UART_LCR Masks */
+#define WLS(x)                   (((x)-5) & 0x03)  /* Word Length Select */
+#define STB                      0x04  /* Stop Bits */
+#define PEN                      0x08  /* Parity Enable */
+#define EPS                      0x10  /* Even Parity Select */
+#define STP                      0x20  /* Stick Parity */
+#define SB                       0x40  /* Set Break */
+#define DLAB                     0x80  /* Divisor Latch Access */
+
+/* UART_LSR Masks */
+#define DR                       0x01  /* Data Ready */
+#define OE                       0x02  /* Overrun Error */
+#define PE                       0x04  /* Parity Error */
+#define FE                       0x08  /* Framing Error */
+#define BI                       0x10  /* Break Interrupt */
+#define THRE                     0x20  /* THR Empty */
+#define TEMT                     0x40  /* TSR and UART_THR Empty */
+#define TFI                      0x80  /* Transmission Finished Indicator */
+
+/* UART_IER Masks */
+#define ERBFI                    0x01  /* Enable Receive Buffer Full Interrupt */
+#define ETBEI                    0x02  /* Enable Transmit Buffer Empty Interrupt */
+#define ELSI                     0x04  /* Enable RX Status Interrupt */
+#define EDSSI                    0x08  /* Enable Modem Status Interrupt */
+#define EDTPTI                   0x10  /* Enable DMA Transmit PIRQ Interrupt */
+#define ETFI                     0x20  /* Enable Transmission Finished Interrupt */
+#define ERFCI                    0x40  /* Enable Receive FIFO Count Interrupt */
+
+/* UART_MCR Masks */
+#define XOFF                     0x01  /* Transmitter Off */
+#define MRTS                     0x02  /* Manual Request To Send */
+#define RFIT                     0x04  /* Receive FIFO IRQ Threshold */
+#define RFRT                     0x08  /* Receive FIFO RTS Threshold */
+#define LOOP_ENA                 0x10  /* Loopback Mode Enable */
+#define FCPOL                    0x20  /* Flow Control Pin Polarity */
+#define ARTS                     0x40  /* Automatic Request To Send */
+#define ACTS                     0x80  /* Automatic Clear To Send */
+
+/* UART_MSR Masks */
+#define SCTS                     0x01  /* Sticky CTS */
+#define CTS                      0x10  /* Clear To Send */
+#define RFCS                     0x20  /* Receive FIFO Count Status */
+
+/* UART_GCTL Masks */
+#define UCEN                     0x01  /* Enable UARTx Clocks */
+#define IREN                     0x02  /* Enable IrDA Mode */
+#define TPOLC                    0x04  /* IrDA TX Polarity Change */
+#define RPOLC                    0x08  /* IrDA RX Polarity Change */
+#define FPE                      0x10  /* Force Parity Error On Transmit */
+#define FFE                      0x20  /* Force Framing Error On Transmit */
+
+#ifdef BFIN_UART_BF54X_STYLE
+# define OFFSET_DLL              0x00  /* Divisor Latch (Low-Byte)        */
+# define OFFSET_DLH              0x04  /* Divisor Latch (High-Byte)       */
+# define OFFSET_GCTL             0x08  /* Global Control Register         */
+# define OFFSET_LCR              0x0C  /* Line Control Register           */
+# define OFFSET_MCR              0x10  /* Modem Control Register          */
+# define OFFSET_LSR              0x14  /* Line Status Register            */
+# define OFFSET_MSR              0x18  /* Modem Status Register           */
+# define OFFSET_SCR              0x1C  /* SCR Scratch Register            */
+# define OFFSET_IER_SET          0x20  /* Set Interrupt Enable Register   */
+# define OFFSET_IER_CLEAR        0x24  /* Clear Interrupt Enable Register */
+# define OFFSET_THR              0x28  /* Transmit Holding register       */
+# define OFFSET_RBR              0x2C  /* Receive Buffer register         */
+#else /* BF533 style */
+# define OFFSET_THR              0x00  /* Transmit Holding register         */
+# define OFFSET_RBR              0x00  /* Receive Buffer register           */
+# define OFFSET_DLL              0x00  /* Divisor Latch (Low-Byte)          */
+# define OFFSET_DLH              0x04  /* Divisor Latch (High-Byte)         */
+# define OFFSET_IER              0x04  /* Interrupt Enable Register         */
+# define OFFSET_IIR              0x08  /* Interrupt Identification Register */
+# define OFFSET_LCR              0x0C  /* Line Control Register             */
+# define OFFSET_MCR              0x10  /* Modem Control Register            */
+# define OFFSET_LSR              0x14  /* Line Status Register              */
+# define OFFSET_MSR              0x18  /* Modem Status Register             */
+# define OFFSET_SCR              0x1C  /* SCR Scratch Register              */
+# define OFFSET_GCTL             0x24  /* Global Control Register           */
+/* code should not need IIR, so force build error if they use it */
+# undef OFFSET_IIR
+#endif
+
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits.  So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+struct bfin_uart_regs {
+#ifdef BFIN_UART_BF54X_STYLE
+	__BFP(dll);
+	__BFP(dlh);
+	__BFP(gctl);
+	__BFP(lcr);
+	__BFP(mcr);
+	__BFP(lsr);
+	__BFP(msr);
+	__BFP(scr);
+	__BFP(ier_set);
+	__BFP(ier_clear);
+	__BFP(thr);
+	__BFP(rbr);
+#else
+	union {
+		u16 dll;
+		u16 thr;
+		const u16 rbr;
+	};
+	const u16 __pad0;
+	union {
+		u16 dlh;
+		u16 ier;
+	};
+	const u16 __pad1;
+	const __BFP(iir);
+	__BFP(lcr);
+	__BFP(mcr);
+	__BFP(lsr);
+	__BFP(msr);
+	__BFP(scr);
+	const u32 __pad2;
+	__BFP(gctl);
+#endif
+};
+#undef __BFP
+
+#ifndef port_membase
+# define port_membase(p) (((struct bfin_serial_port *)(p))->port.membase)
+#endif
+
+#define UART_GET_CHAR(p)      bfin_read16(port_membase(p) + OFFSET_RBR)
+#define UART_GET_DLL(p)       bfin_read16(port_membase(p) + OFFSET_DLL)
+#define UART_GET_DLH(p)       bfin_read16(port_membase(p) + OFFSET_DLH)
+#define UART_GET_GCTL(p)      bfin_read16(port_membase(p) + OFFSET_GCTL)
+#define UART_GET_LCR(p)       bfin_read16(port_membase(p) + OFFSET_LCR)
+#define UART_GET_MCR(p)       bfin_read16(port_membase(p) + OFFSET_MCR)
+#define UART_GET_MSR(p)       bfin_read16(port_membase(p) + OFFSET_MSR)
+
+#define UART_PUT_CHAR(p, v)   bfin_write16(port_membase(p) + OFFSET_THR, v)
+#define UART_PUT_DLL(p, v)    bfin_write16(port_membase(p) + OFFSET_DLL, v)
+#define UART_PUT_DLH(p, v)    bfin_write16(port_membase(p) + OFFSET_DLH, v)
+#define UART_PUT_GCTL(p, v)   bfin_write16(port_membase(p) + OFFSET_GCTL, v)
+#define UART_PUT_LCR(p, v)    bfin_write16(port_membase(p) + OFFSET_LCR, v)
+#define UART_PUT_MCR(p, v)    bfin_write16(port_membase(p) + OFFSET_MCR, v)
+
+#ifdef BFIN_UART_BF54X_STYLE
+
+#define UART_CLEAR_IER(p, v)  bfin_write16(port_membase(p) + OFFSET_IER_CLEAR, v)
+#define UART_GET_IER(p)       bfin_read16(port_membase(p) + OFFSET_IER_SET)
+#define UART_SET_IER(p, v)    bfin_write16(port_membase(p) + OFFSET_IER_SET, v)
+
+#define UART_CLEAR_DLAB(p)    /* MMRs not muxed on BF54x */
+#define UART_SET_DLAB(p)      /* MMRs not muxed on BF54x */
+
+#define UART_CLEAR_LSR(p)     bfin_write16(port_membase(p) + OFFSET_LSR, -1)
+#define UART_GET_LSR(p)       bfin_read16(port_membase(p) + OFFSET_LSR)
+#define UART_PUT_LSR(p, v)    bfin_write16(port_membase(p) + OFFSET_LSR, v)
+
+/* This handles hard CTS/RTS */
+#define UART_CLEAR_SCTS(p)      bfin_write16((port_membase(p) + OFFSET_MSR), SCTS)
+#define UART_GET_CTS(x)         (UART_GET_MSR(x) & CTS)
+#define UART_DISABLE_RTS(x)     UART_PUT_MCR(x, UART_GET_MCR(x) & ~(ARTS | MRTS))
+#define UART_ENABLE_RTS(x)      UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS | ARTS)
+#define UART_ENABLE_INTS(x, v)  UART_SET_IER(x, v)
+#define UART_DISABLE_INTS(x)    UART_CLEAR_IER(x, 0xF)
+
+#else /* BF533 style */
+
+#define UART_CLEAR_IER(p, v)  UART_PUT_IER(p, UART_GET_IER(p) & ~(v))
+#define UART_GET_IER(p)       bfin_read16(port_membase(p) + OFFSET_IER)
+#define UART_PUT_IER(p, v)    bfin_write16(port_membase(p) + OFFSET_IER, v)
+#define UART_SET_IER(p, v)    UART_PUT_IER(p, UART_GET_IER(p) | (v))
+
+#define UART_CLEAR_DLAB(p)    do { UART_PUT_LCR(p, UART_GET_LCR(p) & ~DLAB); SSYNC(); } while (0)
+#define UART_SET_DLAB(p)      do { UART_PUT_LCR(p, UART_GET_LCR(p) | DLAB); SSYNC(); } while (0)
+
+#ifndef put_lsr_cache
+# define put_lsr_cache(p, v) (((struct bfin_serial_port *)(p))->lsr = (v))
+#endif
+#ifndef get_lsr_cache
+# define get_lsr_cache(p)    (((struct bfin_serial_port *)(p))->lsr)
+#endif
+
+/* The hardware clears the LSR bits upon read, so we need to cache
+ * some of the more fun bits in software so they don't get lost
+ * when checking the LSR in other code paths (TX).
+ */
+static inline void UART_CLEAR_LSR(void *p)
+{
+	put_lsr_cache(p, 0);
+	bfin_write16(port_membase(p) + OFFSET_LSR, -1);
+}
+static inline unsigned int UART_GET_LSR(void *p)
+{
+	unsigned int lsr = bfin_read16(port_membase(p) + OFFSET_LSR);
+	put_lsr_cache(p, get_lsr_cache(p) | (lsr & (BI|FE|PE|OE)));
+	return lsr | get_lsr_cache(p);
+}
+static inline void UART_PUT_LSR(void *p, uint16_t val)
+{
+	put_lsr_cache(p, get_lsr_cache(p) & ~val);
+}
+
+/* This handles soft CTS/RTS */
+#define UART_GET_CTS(x)        gpio_get_value((x)->cts_pin)
+#define UART_DISABLE_RTS(x)    gpio_set_value((x)->rts_pin, 1)
+#define UART_ENABLE_RTS(x)     gpio_set_value((x)->rts_pin, 0)
+#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
+#define UART_DISABLE_INTS(x)   UART_PUT_IER(x, 0)
+
+#endif
+
+#ifndef BFIN_UART_TX_FIFO_SIZE
+# define BFIN_UART_TX_FIFO_SIZE 2
+#endif
+
+#endif /* __BFIN_ASM_SERIAL_H__ */