Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...

6 files changed, 85 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
index 50bf611a4d2c..13e70409e8ac 100644
--- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
+++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
@@ -12,6 +12,7 @@ Required properties:
   - "amlogic,meson-gxbb-mmc"
   - "amlogic,meson-gxl-mmc"
   - "amlogic,meson-gxm-mmc"
+  - "amlogic,meson-axg-mmc"
 - clocks     : A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
 - clock-names: Should contain the following:
 	"core" - Main peripheral bus clock
@@ -19,6 +20,7 @@ Required properties:
 	"clkin1" - Other parent clock of internal mux
   The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the
   clock rate requested by the MMC core.
+- resets     : phandle of the internal reset line
 
 Example:
 
@@ -29,4 +31,5 @@ Example:
 		clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
 		clock-names = "core", "clkin0", "clkin1";
 		pinctrl-0 = <&emmc_pins>;
+		resets = <&reset RESET_SD_EMMC_A>;
 	};
diff --git a/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt
new file mode 100644
index 000000000000..b0f0999ea1a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt
@@ -0,0 +1,29 @@
+* Mellanox Bluefield SoC specific extensions to the Synopsys Designware
+  Mobile Storage Host Controller
+
+Read synopsys-dw-mshc.txt for more details
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC
+specific extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be one of the following.
+  - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC
+    specific extensions.
+
+Example:
+
+	/* Mellanox Bluefield SoC MMC */
+	mmc@6008000 {
+		compatible = "mellanox,bluefield-dw-mshc";
+		reg = <0x6008000 0x400>;
+		interrupts = <32>;
+		fifo-depth = <0x100>;
+		clock-frequency = <24000000>;
+		bus-width = <8>;
+		cap-mmc-highspeed;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt
new file mode 100644
index 000000000000..7cd8c432d7c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/jz4740.txt
@@ -0,0 +1,38 @@
+* Ingenic JZ47xx MMC controllers
+
+This file documents the device tree properties used for the MMC controller in
+Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties
+described in mmc.txt.
+
+Required properties:
+- compatible: Should be one of the following:
+  - "ingenic,jz4740-mmc" for the JZ4740
+  - "ingenic,jz4780-mmc" for the JZ4780
+- reg: Should contain the MMC controller registers location and length.
+- interrupts: Should contain the interrupt specifier of the MMC controller.
+- clocks: Clock for the MMC controller.
+
+Optional properties:
+- dmas: List of DMA specifiers with the controller specific format
+        as described in the generic DMA client binding. A tx and rx
+        specifier is required.
+- dma-names: RX and TX  DMA request names.
+        Should be "rx" and "tx", in that order.
+
+For additional details on DMA client bindings see ../dma/dma.txt.
+
+Example:
+
+mmc0: mmc@13450000 {
+	compatible = "ingenic,jz4780-mmc";
+	reg = <0x13450000 0x1000>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <37>;
+
+	clocks = <&cgu JZ4780_CLK_MSC0>;
+	clock-names = "mmc";
+
+	dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, <&dma JZ4780_DMA_MSC0_TX 0xffffffff>;
+	dma-names = "rx", "tx";
+};
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 467cd7b147ce..f5a0923b34ca 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -19,6 +19,8 @@ Optional properties:
 - wp-gpios: Specify GPIOs for write protection, see gpio binding
 - cd-inverted: when present, polarity on the CD line is inverted. See the note
   below for the case, when a GPIO is used for the CD line
+- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt.
+  It's only valid when cd-gpios is present.
 - wp-inverted: when present, polarity on the WP line is inverted. See the note
   below for the case, when a GPIO is used for the WP line
 - disable-wp: When set no physical WP line is present. This property should
@@ -56,6 +58,10 @@ Optional properties:
 - fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type.
   The value <n> is the driver type as specified in the eMMC specification
   (table 206 in spec version 5.1).
+- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could
+  be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay
+  waiting for I/O signalling and card power supply to be stable, regardless of
+  whether pwrseq-simple is used. Default to 10ms if no available.
 
 *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
 polarity properties, we have to fix the meaning of the "normal" and "inverted"
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
index 51775a372c06..393848c2138e 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt
@@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings.
 
 Required properties:
 - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers
+	      Should be "ti,k2g-sdhci" for K2G
 - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1
+	     (Not required for K2G).
+- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50",
+		 "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104",
+		 "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11",
+		 "hs200_1_8v",
+- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 	mmc1: mmc@4809c000 {
diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
index 2d5287eeed95..ee978c95189d 100644
--- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
@@ -26,6 +26,8 @@ Required properties:
 		"renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC
 		"renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC
 		"renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC
+		"renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC
+		"renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC
 		"renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC
 		"renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller
 		"renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller