summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-09-25x86: zboot: Allow setting a separate setup base addressSimon Glass1-8/+35
At present the setup block is always obtained from the image automatically. In some cases it can be useful to use a setup block obtained elsewhere, e.g. if the image has already been unpacked. Add an argument to support this and update the logic to use it if provided. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: adjust maxargs to 7 for 'zboot start'] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Set environment variables for image locationsSimon Glass2-0/+7
At present it is not possible to tell from a script where the setup block is, or where the image was loaded to. Add environment variables for this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Add an 'setup' subcommandSimon Glass1-7/+25
Add a subcommand that sets up the kernel ready for execution. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Add an 'load' subcommandSimon Glass1-7/+16
Add a subcommand that loads the kernel into the right places in memory. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: adjust ZBOOT_STATE_INFO value to match the command order] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Add an 'info' subcommandSimon Glass1-3/+15
Add a little subcommand that prints out where the kernel was loaded and its setup pointer. Run it by default in the normal boot. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Add a 'go' subcommandSimon Glass1-4/+25
Split out the code that actually boots linux into a separate sub-command. Add base_ptr to the state to support this. Show an error if the boot fails, since this should not happen. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Set up a sub-command structureSimon Glass1-5/+61
Add subcommands to zboot. At present there is only one called 'start' which does the whole boot. It is the default command so is optional. Change the 's' string variable to const while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: reduce maxargs to 6 of 'zboot start' subcommand] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zimage: Disable interrupts just before bootingSimon Glass1-1/+1
At present if an error occurs while setting up the boot, interrupts are left disabled. Move this call later in the sequence to avoid this problem. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Correct image typeSimon Glass1-2/+1
At present U-Boot sets a loader type of 8 which means LILO version 8, according to the spec. Update it to 0x80, which means U-Boot with no particular version. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zboot: Move kernel-version code into a functionSimon Glass1-16/+27
To help reduce the size and complexity of load_zimage(), move the code that reads the kernel version into a separate function. Update get_boot_protocol() to allow printing the 'Magic signature' message only once, under control of its callers. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zimage: Avoid using #ifdefSimon Glass1-9/+5
Use IS_ENABLED() instead of #ifdef in this file. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: zimage: Use a state struct to hold the stateSimon Glass1-15/+29
At present the 'zboot' command does everything in one go. It would be better if it supported sub-commands like bootm, so it is possible to examine what will be booted before actually booting it. In preparation for this, move the 'state' of the command into a struct. This will allow it to be shared among multiple functions in this file. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-25x86: Update the bootparam headerSimon Glass1-6/+19
This header is missing a few of the newer features from the specification. Add these as well as a link to the spec. Also use the BIT() macros where appropriate. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-24pci: layerscape: Fixup PCIe EP mode DT nodes for LX2160A rev2Hou Zhiqiang1-0/+26
LX2160A rev2 uses different PCIe controller, so EP mode DT nodes also need to be fixed up. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24net: pfe_eth: Remove non-DM code check from pfe_spi_flash_initKuldeep Singh1-11/+5
CONFIG_DM_SPI_FLASH is only supported now with passing of driver conversion deadline from non-DM to DM model. Hence, it's safe to remove non-DM code check from pfe_spi_flash_init. Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of reading reading values from DT. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24net: pfe_eth: Fix resoure leak in pfe_spi_flash_initKuldeep Singh1-0/+4
Fix Coverity issue: RESOURCE_LEAK. leaked_storage: Variable addr going out of scope leaks the storage it points to. Fixes: e0152dbed683 ("net: pfe_eth: Use spi_flash_read API to access flash memory") Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24arm: dts: lx2160a: Add IO rangeWasim Khan1-6/+12
Add IO range property to fix below error on uboot PCI: Failed autoconfig bar 18 Signed-off-by: Wasim Khan <wasim.khan@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24driver: net: fm: add support for XFIMadalin Bucur1-1/+2
All the 10G ports that were working in XFI mode were described as using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time). Add the minimal changes required for the FMan code to support XFI. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24ls1012a, pfe_eth: Update probe to avoid resource leakChaitanya Sakinam1-11/+6
PFE DDR addresses are now stored on to a stack varaiable rather dynamic allocation. Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24ls1012a, pfe_eth: correction in delay implementationChaitanya Sakinam1-2/+3
correction in delay implementation before we exit out of tx timeout. Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24drivers: net: phy: Use Aquantia driver for AQR113CMadalin Bucur1-0/+15
Add support for AQR113C PHY Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24drivers: net: ldpaa_eth: lx2160a: fix bug in checking if a DPMAC is enabledGrigore Popescu1-2/+2
The next DPMAC was always verified if it is enabled. In case of DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will be considered disabled and not detected by uboot. Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24armv8: dts: fsl-lx2160a: add gpio0 gpio1 gpio3 DT nodeshui.song1-0/+33
add gpio0 gpio1 gpio3 DT nodes to fsl-lx21600.dtsi Signed-off-by: hui.song <hui.song_1@nxp.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24armv8: lx2160a: fix reset sequenceMeenakshi Aggarwal1-6/+8
Make sure that SW_RST_REQ and RST_REQ_MSK are cleared before triggering hardware reset request. Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24lx2160: Correct sd_boot environment variableMeenakshi Aggarwal2-2/+2
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board: freescale: emc2305: Pass chip_addr to set_fan_speedWasim Khan3-14/+12
emc2305 is a common driver. It should not use platform specific i2c address for slave device. Pass chip_addr as agrument to emc2305_init() and set_fan_speed() so that emc2305 driver can be used with different platforms. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale/lsch3: Correct entry for 0.9vMartin Kaistra1-1/+1
According to the reference manual of LS2088A, for a VDD voltage of 0.9V, the entry should be at 01000b. Fixes: 4911948ec73 ("board/freescale,lsch3: Add entry for 0.9v") Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24arm64: Layerscape: Survive LPI one-way reset workaroundHou Zhiqiang5-1/+40
The workaround of LPI one-way reset issue is broken by the series: https://patchwork.ozlabs.org/project/uboot/list/?series=192398 This patch is to add DT node for GIC RD tables and create corresponding reserved-memory node in kernel DT to fix it. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24fsl-layerscape: enable dwc3 snooping featureRan Wang1-0/+37
Configure DWC3’s cache type to ‘cacheable’ for better performance. Actually related register definition and values are SoC specific, which means this setting is only applicable to Layerscape SoC, not generic for all platforms which have integrated DWC3 IP. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini7-1/+63
- Enable NET_RANDOM_ETHADDR on Espressobin (Acked-by Kosta) - Espressobin & Clearfog: fdtfile enhancements - A37xx PCI: Disable link training when unloading driver - A37xx: increase CONFIG_SYS_BOOTM_LEN to 64MB - Add Macronix mx25u12835f support, used on uDPU and ESPRESSObin v7 - dns325: Correct CONFIG_NR_DRAM_BANKS parameter
2020-09-24Merge tag 'xilinx-for-v2021.01' of ↵Tom Rini51-298/+499
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2021.01 arm64: - Support for bigger U-Boot images compiled with PIE microblaze: - Extend support for LE/BE systems zynqmp: - Refactor silicon ID detection code with using firmware interface - Add support for saving variables based on bootmode zynqmp-r5: - Fix MPU mapping and defconfig setting. xilinx: - Minor driver changes: names alignment - Enable UBIFS - Minor DT and macros fixes - Fix boot with appended DT - Fix distro boot cmd: - pxe: Add fixing for platforms with manual relocation support clk: - fixed_rate: Add DM flag to support early boot on r5 fpga: - zynqmppl: Use only firmware interface and enable SPL build serial: - uartlite: Enable for ARM systems and support endians mmc: - zynq: Fix indentation net: - gem: Support for multiple phys - emac: Fix 64bit support and enable it for arm64 kconfig: - Setup default values for Xilinx platforms - Fix dependecies for Xilinx drivers - Source board Kconfig only when platform is enabled - Fix FPGA Kconfig entry with SPL - Change some defconfig values bindings: - Add binding doc for vsc8531
2020-09-24Merge branch 'mpc85xx-for-v2021.01' into nextTom Rini204-4564/+1235
- Add DM_SPI, DM_SPI_FLASH support for powerpc platforms - Add DM_ETH support on P1010RDB, P1020RDB, P2020RDB - Remove some un-maintained powerpc platforms - Add USB_STORAGE support in config
2020-09-24configs: powerpc: add usb (host) mass storage supportRan Wang48-0/+48
commit 0cfccb54014b ("configs: Resync with savedefconfig") removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig files, whicih would block the use case of system loading rootfs from USB drives, add them back. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P5040DS secure boot configsPriyanka Jain2-123/+0
Remove NXP powerpc P5040DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P5020DS board supportPriyanka Jain15-495/+0
Remove NXP powerpc P5020DS board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24powerpc:Remove P4080DS secure boot configsPriyanka Jain2-60/+0
Remove NXP powerpc P4080DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P3041DS secure boot configsPriyanka Jain3-123/+0
Remove NXP powerpc P3041DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1024RDB board supportPriyanka Jain9-375/+0
Remove NXP powerpc P1024RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1021RDB board supportPriyanka Jain14-745/+1
Remove NXP powerpc P1021RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1020MBG board supportPriyanka Jain9-277/+5
Remove NXP powerpc P1020MBG board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1020UTM board supportPriyanka Jain10-276/+1
Remove NXP powerpc P1020UTM board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1025RDB board supportPriyanka Jain12-469/+4
Remove NXP powerpc P1025RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P1010RDB secure boot configsPriyanka Jain13-779/+0
Remove NXP powerpc P1010RDB secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove p1023rdb board supportPriyanka Jain10-782/+0
Remove NXP powerpc p1023rdb board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P2020RDB: Enable DM_ETH configHou Zhiqiang8-0/+24
Enable the DM_ETH and DM_MDIO config. On P2020RDB, the eTSEC1 is connecting with a switch VSC7385, so also enable the fixed PHY support. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24dts: powerpc: p2020rdb: Add eTSEC DT nodesHou Zhiqiang8-2/+170
P2020RDB implements 3 enhanced three-speed Ethernet controllers, and the connection is shown below: eTSEC1: Connected to RGMII switch VSC7385 eTSEC2: Connected to SGMII PHY VSC8221 eTSEC3: Connected to SGMII PHY AR8021 Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P1010RDB: Enable DM_ETH configHou Zhiqiang16-0/+32
Enable the DM_ETH and DM_MDIO config. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24p1010rdb: Don't compile board_eth_init() for DM_ETHHou Zhiqiang1-0/+2
The board_eth_init() is only used by legacy ethernet driver framework, so do not compile it when DM_ETH config has been selected. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24dts: powerpc: p1010rdb: Add eTSEC DT nodesHou Zhiqiang2-0/+75
P1010RDB implements 3 enhanced three-speed Ethernet controllers, and the connection is shown below: eTSEC1: Connected to RGMII PHY AR8033 eTSEC2: Connected to SGMII PHY AR8033 eTSEC3: Connected to SGMII PHY AR8033 Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P1020RDB: Enable DM_ETH configHou Zhiqiang12-0/+36
Enable the DM_ETH and DM_MDIO config. On P1020RDB, the eTSEC1 is connecting with a switch VSC7385, so also enable the fixed PHY support. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit v1.2.3 (git 2.39.0) at 2026-10-01 03:58:27 +0300