starfive-tech/u-boot.git/lib/fdtdec.c, branch rtthread_AMP

pci: Drop DM_PCI check from fdtdec

2021-09-13T22:23:13+00:00

We don't need this check anymore since when PCI is enabled, driver model is always used. Sadly this doesn't work with nds32 for some reason to do with the toolchain. Add a work-around for that. Signed-off-by: Simon Glass

Merge https://source.denx.de/u-boot/custodians/u-boot-samsung

2021-08-03T13:07:01+00:00

global: Convert simple_strtoul() with decimal to dectoul()

2021-08-02T17:32:14+00:00

It is a pain to have to specify the value 10 in each call. Add a new dectoul() function and update the code to use it. Signed-off-by: Simon Glass

samsung: exynos: Convert SROMC interface to a driver

2021-07-27T01:34:27+00:00

Add a bus driver for this and use it to configure the bus parameters for the Ethernet interface. Drop the old pre-driver-model code. Switch over to use driver model for Ethernet. Signed-off-by: Simon Glass Reviewed-by: Jaehoon Chung Signed-off-by: Minkyu Kang

dm: core: Add address translation in fdt_get_resource

2021-04-29T10:23:39+00:00

Today of_address_to_resource() is called only in ofnode_read_resource() for livetree support and fdt_get_resource() is called when livetree is not supported. The fdt_get_resource() doesn't do the address translation so when it is required, but the address translation is done by ofnode_read_resource() caller, for example in drivers/firmware/scmi/smt.c::scmi_dt_get_smt_buffer() { ... ret = ofnode_read_resource(args.node, 0, &resource); if (ret) return ret; faddr = cpu_to_fdt32(resource.start); paddr = ofnode_translate_address(args.node, &faddr); ... The both behavior should be aligned and the address translation must be called in fdt_get_resource() and removed for each caller. Fixes: a44810123f9e ("dm: core: Add dev_read_resource() to read device resources") Signed-off-by: Patrick Delaunay Acked-by: Etienne Carriere

Merge branch '2021-02-02-drop-asm_global_data-when-unused'

2021-02-15T15:16:45+00:00

- Merge the patch to take out of

Revert "fdtdec: Use CONFIG_IS_ENABLED in board_fdt_blob_setup()"

2021-02-15T15:06:23+00:00

On Rockchip platforms we need this area of code in TPL, but there is no TPL_SEPARATE_BSS symbol. This reverts commit 0a2aaab0b678fd1778ff2fc59d0770fc82995532. Reported-by: Markus Reichl Reported-by: Jesper Schmitz Mouridsen Reported-by: Peter Robinson Tested-by: Peter Robinson Signed-off-by: Tom Rini

fdtdec: Cast prior_stage_fdt_address with uintptr_t

2021-02-03T10:38:41+00:00

At present prior_stage_fdt_address is declared as phys_addr_t. On a 32-bit platform where phys_addr_t can be 64-bit, assigning its value to gd->fdt_blob which is a pointer, can cause warnings. Cast it to uintptr_t before the assignment. Signed-off-by: Bin Meng Reviewed-by: Simon Glass

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42+00:00

Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include at all, so remove that include. Signed-off-by: Simon Glass Signed-off-by: Tom Rini

fdtdec: Use CONFIG_IS_ENABLED in board_fdt_blob_setup()

2021-01-27T22:03:16+00:00

This setting may be different in SPL and TPL. Update the code to check the correct setting. Signed-off-by: Simon Glass