starfive-tech/u-boot.git/include/configs/vcoreiii.h, branch rtthread_AMP

Convert CONFIG_CONS_INDEX to Kconfig

2020-06-26T14:29:06+00:00

This converts the following to Kconfig: CONFIG_CONS_INDEX Signed-off-by: Tom Rini

Convert CONFIG_BOARD_TYPES to Kconfig

2020-06-26T14:29:05+00:00

This converts the following to Kconfig: CONFIG_BOARD_TYPES Signed-off-by: Tom Rini

Convert CONFIG_BOARD_EARLY_INIT_F et al to Kconfig

2020-06-26T14:29:05+00:00

This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F CONFIG_BOARD_EARLY_INIT_R Signed-off-by: Tom Rini

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

mips: vcoreiii: Ajust CONFIG_SYS_MEMTEST_END

2020-04-09T16:55:59+00:00

This patch ajust CONFIG_SYS_MEMTEST_END for vcoreiii-based systems to avoid overwriting the relocated u-boot. The former setting was too agressive with networking etc. enabled on some platforms. Reviewed-by: Alexandre Belloni Reviewed-by: Horatiu Vultur Signed-off-by: Lars Povlsen

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

2019-11-20T23:31:24+00:00

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one board where we can simply multiple CONFIG_ENV_SIZE by two for the same result. The other place where we could but were not previously using this is for where env_internal.h checks for if we should set ENV_IS_EMBEDDED. This seems like the most likely use, historically, of the variable, but it was not used. Add logic to check for this now. Cc: Wolfgang Denk Cc: Joe Hershberger Signed-off-by: Tom Rini Reviewed-by: Simon Glass Acked-by: Joe Hershberger

defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT

2019-11-12T16:08:00+00:00

Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini

configs: vcoreiii: Change CONFIG_ENV_SIZE

2019-04-12T15:32:51+00:00

Shrink the environment size for 3 reasons: - reading the environment it is slow, therefore having a smaller env improves the speed. - usually in the environment there are only few variables, therefore the enviromnent is almost empty. - because the same image can run on different boards which may have different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE can't be change, it is set to least common multiple of the page sizes. Adding this change improves the boot time. Before update for reading the entire environment it took ~850 msec, after the change it takes ~40 msecs. Signed-off-by: Horatiu Vultur

net: Add MSCC Jaguar2 network driver.

2019-04-12T15:32:51+00:00

Add network driver for Microsemi Ethernet switch. It is present on Jaguar2 SoCs. Reviewed-by: Daniel Schwierzeck Signed-off-by: Horatiu Vultur