starfive-tech/u-boot.git/include/configs/udoo.h, branch rtthread_AMP

ARM: imx: udoo: convert to DM_ETH

2021-04-08T18:29:54+00:00

Convert the UDOO board to use DM_ETH. Signed-off-by: Peter Robinson Cc: Fabio Estevam Cc: Stefano Babic

ARM: imx: udoo: Convert block devices to DM

2021-04-08T18:29:54+00:00

Enable DM block, DM MMC and DM SATA support on iMX6 Udoo convert board code to match the DM support. Signed-off-by: Peter Robinson Cc: Fabio Estevam Cc: Stefano Babic

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

2020-08-08T15:03:52+00:00

This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29+00:00

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

common: Drop linux/stringify.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header. Signed-off-by: Simon Glass

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

arm: udoo: Convert to distro config

2018-10-22T13:18:49+00:00

Instead of keeping a custom environment, use a more generic approach by switching to distro config. Signed-off-by: Dirk Meul Reviewed-by: Fabio Estevam

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54+00:00

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini