starfive-tech/u-boot.git/include/configs/stmark2.h, branch rtthread_AMP

remove obsolete option CONFIG_JFFS2_CMDLINE

2020-12-02T21:21:58+00:00

This option is obsolete since 2009 and can be removed globally. CC: Stefan Roese Signed-off-by: Holger Brunck Reviewed-by: Stefan Roese

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

Convert CONFIG_BOOTARGS to Kconfig

2020-06-26T14:29:05+00:00

This converts the following to Kconfig: CONFIG_BOOTARGS Signed-off-by: Tom Rini

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

m68k: Drop CONFIG_MCFPIT support

2020-01-10T15:25:13+00:00

All platforms currently use the "MCFTMR" DMA timer rather than the PIT timer, so drop the MCFPIT code. Cc: Huan Wang Cc: Angelo Dureghello Cc: TsiChung Liew Cc: Wolfgang Wegner Signed-off-by: Tom Rini Reviewed-by: Angelo Dureghello

configs: purge unneeded fec defines

2020-01-10T15:25:13+00:00

Remove unneeded fec-related defines after fec moved as dm. Signed-off-by: Angelo Durgehello

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

configs: remove CONFIG_SYS_DSPI_XX references

2019-05-24T12:11:58+00:00

This patch removes CONFIG_SYS_DSPI_XX options from include/configs "m68k" .h board files, since CTAR registers are now set with default values in the cf_spi driver initialization, and configurable by devicetree. Note, these options cannot be totally removed from the whitelist, since still used from boards using fsl_dspi.c (mostly arm-based boards). Reviewed-by: Simon Glass Signed-off-by: Angelo Dureghello

Convert CONFIG_ENV_SPI_* to Kconfig

2019-03-25T21:36:59+00:00

This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53+00:00

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay