starfive-tech/u-boot.git/include/configs/r2dplus.h, branch rtthread_AMP

sh: r2dplus: Enable DM_SERIAL and DM_CLK

2020-08-02T17:58:27+00:00

Switch r2dplus to DM and DT probing for serial and clock. Signed-off-by: Marek Vasut Cc: Nobuhiro Iwamatsu

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

sh: r2dplus: Switch to DM PCI driver

2019-09-02T15:38:43+00:00

Add DT entry for the DM PCI driver, update board configs and drop ad-hoc board init code for the PCI bus. Instead, let the DM PCI driver initialize and operate the hardware. Signed-off-by: Marek Vasut Cc: Nobuhiro Iwamatsu

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50+00:00

This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford [trini: Re-migrate] Signed-off-by: Tom Rini

sh: tmu: Clean up CONFIG_SH_TMU_CLK_FREQ

2018-09-15T01:19:07+00:00

The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2, while the old SH parts use CONFIG_SYS_CLK_FREQ directly. Just put this into the TMU implementation and drop the CONFIG_SH_TMU_CLK_FREQ config option. Signed-off-by: Marek Vasut

sh: tmu: Clean up CONFIG_SYS_TMU_CLK_DIV

2018-09-15T01:19:07+00:00

This constant is always 4 , for all boards that exist. Define it once in arch/sh/lib/time.c and remove it from the configs. Signed-off-by: Marek Vasut

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

2018-02-24T02:41:49+00:00

This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford [trini: Re-run the migration] Signed-off-by: Tom Rini

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09+00:00

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini