starfive-tech/u-boot.git/include/configs/mx6ullevk.h, branch rtthread_AMP

configs: migrate CONFIG_IMX_THERMAL to defconfigs

2020-12-07T07:54:29+00:00

Done via moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

2020-08-08T15:03:52+00:00

This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29+00:00

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

common: Drop linux/stringify.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header. Signed-off-by: Simon Glass

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

treewide: Remove unused FSL QSPI config options for IMX platforms

2020-05-01T11:46:22+00:00

Some of these options are not used by the driver anymore and some of them are obsolete as the information is gathered from the dt. So, remove the unused config options now. Signed-off-by: Frieder Schrempf Signed-off-by: Ashish Kumar Signed-off-by: Kuldeep Singh

mx6ullevk: Enable Ethernet support

2020-04-17T16:55:55+00:00

Add Ethernet support using DM_ETH. Signed-off-by: Fabio Estevam Reviewed-by: Peng Fan

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

Kconfig: Migrate CONFIG_CSF_SIZE to Kconfig

2019-10-08T14:35:58+00:00

Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima Reviewed-by: Fabio Estevam

imx: add i.MX6ULZ board

2019-10-08T14:33:45+00:00

Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan Reviewed-by: Ye Li Reviewed-by: Fabio Estevam