starfive-tech/u-boot.git/include/configs/mx6sabre_common.h, branch rtthread_AMP

ARM: imx6: mx6sabre-common: Search for boot components in /boot too

2021-03-01T09:21:36+00:00

Some root filesystem configurations do not have separate /boot partition, but rather place kernel, DT, scripts into /boot directory. Search the /boot directory for these boot components in case they are not found in /, which is the old behavior. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Peng Fan Cc: Stefano Babic Cc: Ye Li Cc: uboot-imx Reviewed-by: Peng Fan

ARM: imx6: mx6sabre-common: Replace fatload with FS_GENERIC load

2021-03-01T09:21:36+00:00

Replace filesystem specific fatload command with a filesystem agnostic load command, so the board can boot from e.g. ext4 too. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Peng Fan Cc: Stefano Babic Cc: Ye Li Cc: uboot-imx Reviewed-by: Peng Fan

configs: migrate CONFIG_IMX_THERMAL to defconfigs

2020-12-07T07:54:29+00:00

Done via moveconfig.py Signed-off-by: Tom Rini

configs: migrate CONFIG_BMP_16/24/32BPP to defconfigs

2020-10-18T13:27:01+00:00

Done with: ./tools/moveconfig.py BMP_16BPP BMP_24BPP BMP_32BPP Signed-off-by: Patrick Delaunay Reviewed-by: Simon Glass

configs: migrate CONFIG_VIDEO_BMP_RLE8 to defconfigs

2020-10-18T13:26:14+00:00

Done with: ./tools/moveconfig.py VIDEO_BMP_RLE8 Signed-off-by: Patrick Delaunay Reviewed-by: Simon Glass

Convert CONFIG_SPLASH_SCREEN et al to Kconfig

2020-08-23T17:43:10+00:00

This converts the following to Kconfig: CONFIG_SPLASH_SCREEN CONFIG_SPLASH_SCREEN_ALIGN CONFIG_SPLASHIMAGE_GUARD CONFIG_SPLASH_SOURCE Signed-off-by: Simon Glass

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29+00:00

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

common: Drop linux/stringify.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header. Signed-off-by: Simon Glass

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH mapping

2020-05-08T13:16:26+00:00

There is no real need to exactly define space for saving patterns for alternate memory test. It is much easier to allocate space on the stack and use it instead of trying to find out space where pattern should be saved. For example if you want to test the whole DDR memory you can't save patter to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses were chosen but that means that OCM needs to be mapped and U-Boot has access permission there. It is easier to remove this limitation and simply save it on stack because it is very clear that memory test can't rewrite U-Boot and U-Boot has also full access to memory where runs from. Signed-off-by: Michal Simek Reviewed-by: Simon Glass Reviewed-by: Stefan Roese Reviewed-by: Heiko Schocher