starfive-tech/u-boot.git/include/configs/mx6memcal.h, branch rtthread_AMP

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29+00:00

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

Convert CONFIG_BAUDRATE to Kconfig

2020-06-26T14:29:05+00:00

This converts the following to Kconfig: CONFIG_BAUDRATE Signed-off-by: Tom Rini

mx6memcal: Finish migration to defconfig options

2020-06-04T19:05:45+00:00

The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson Signed-off-by: Tom Rini

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

treewide: Migrate CONFIG_FSL_ESDHC to Kconfig

2018-04-08T22:31:05+00:00

Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six

mx6memcal: fix comment in board header file

2018-02-04T11:00:58+00:00

The board header file included a reference to the starting point from nitrogen6x.h, but since so much changed, the file bears little resemblance to that file. Signed-off-by: Eric Nelson

mx6memcal: enable SDP support

2018-02-04T11:00:58+00:00

The initial implementation of mx6memcal reset the CPU after running the memory calibration procedure because the generic board has no information about which boot devices are available. Now that we have SDP support in SPL, use it to allow a full U-Boot to be uploaded (i.e. to use "mtest"). Signed-off-by: Eric Nelson Reviewed-by: Fabio Estevam