starfive-tech/u-boot.git/include/configs/mx51evk.h, branch rtthread_AMP

mx51evk: Convert to driver model

2021-03-01T09:21:36+00:00

Make the conversion to driver model as it is mandatory. Tested booting the Linux kernel from the SD card. Signed-off-by: Fabio Estevam

configs: migrate CONFIG_BMP_16/24/32BPP to defconfigs

2020-10-18T13:27:01+00:00

Done with: ./tools/moveconfig.py BMP_16BPP BMP_24BPP BMP_32BPP Signed-off-by: Patrick Delaunay Reviewed-by: Simon Glass

configs: migrate CONFIG_VIDEO_BMP_RLE8 to defconfigs

2020-10-18T13:26:14+00:00

Done with: ./tools/moveconfig.py VIDEO_BMP_RLE8 Signed-off-by: Patrick Delaunay Reviewed-by: Simon Glass

Convert CONFIG_SPLASH_SCREEN et al to Kconfig

2020-08-23T17:43:10+00:00

This converts the following to Kconfig: CONFIG_SPLASH_SCREEN CONFIG_SPLASH_SCREEN_ALIGN CONFIG_SPLASHIMAGE_GUARD CONFIG_SPLASH_SOURCE Signed-off-by: Simon Glass

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

2020-08-08T15:03:52+00:00

This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

Convert CONFIG_MXC_UART to Kconfig

2020-07-17T12:47:29+00:00

This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini Acked-by: Peng Fan

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

mx51evk: Fix U-Boot corruption after saving the environment

2019-12-27T11:14:02+00:00

U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" followed by a "reset" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem to happen in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt