starfive-tech/u-boot.git/include/configs/maxbcm.h, branch rtthread_AMP

arm: mvebu: axp: Set CONFIG_SYS_TCLK globally

2021-08-11T06:42:26+00:00

This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of manual configuration in every board file. Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove useless default CONFIG_SYS_TCLK value from the end of soc.h file. Signed-off-by: Pali Rohár Reviewed-by: Stefan Roese

i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACY

2021-07-28T18:29:37+00:00

It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less than a year away. Also we want to have a CONFIG_I2C for U-Boot proper just like we have CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules. Rename this symbol so it is clear it is going away. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher

Convert CONFIG_CMD_ASKENV et al to Kconfig

2020-06-04T22:10:02+00:00

This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig

2019-08-26T00:59:00+00:00

This converts the following to Kconfig: CONFIG_SYS_SPI_U_BOOT_OFFS Signed-off-by: Hannes Schmelzer [trini: Expose this for SPL_SPI_SUNXI for now] Signed-off-by: Tom Rini

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

2019-04-30T01:41:40+00:00

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt [trini: Re-run migration] Signed-off-by: Tom Rini

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53+00:00

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay

treewide: Move CONFIG_PHY_MARVELL to Kconfig

2018-05-15T01:28:38+00:00

The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards already had it in their Kconfig), but had not been moved for older boards. Move it to the defconfigs for all boards. Signed-off-by: Mario Six Acked-by: Joe Hershberger

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig

2018-04-11T17:22:00+00:00

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut Cc: Tom Rini