starfive-tech/u-boot.git/include/configs/edison.h, branch rtthread_AMP

x86: edison: Move config SYS_MALLOC_LEN to Kconfig

2020-09-21T01:47:24+00:00

This patch moves the the config SYS_MALLOC_LEN to Kconfig as it is already done for zynq arch in commit 01aa5b8f0503 ("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq"). Signed-off-by: Andy Shevchenko Reviewed-by: Simon Glass Reviewed-by: Bin Meng

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

2020-08-08T15:03:52+00:00

This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig

2019-05-04T17:04:12+00:00

This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek , these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan Acked-by: Lukasz Majewski Acked-by: Patrick Delaunay Acked-by: Ramon Fried Reviewed-by: Andy Shevchenko Tested-by: Sébastien Szymanski

x86: edison: Remove staled comments from configuration header

2018-12-31T01:42:41+00:00

Since some options had been moved to defconfig from header, the leftover comments are not needed anymore. Remove them. Signed-off-by: Andy Shevchenko Reviewed-by: Bin Meng

x86: edison: move CONFIG_BOOTCOMMAND from header file to defconfig

2018-12-31T01:42:41+00:00

Use defconfig instead of header file for CONFIG_BOOTCOMMAND. Signed-off-by: Andy Shevchenko Reviewed-by: Bin Meng

x86: edison: move CONFIG_CMD_PCI from header file to defconfig

2018-12-31T01:42:41+00:00

Use defconfig instead of header file for CONFIG_CMD_PCI. Signed-off-by: Andy Shevchenko Reviewed-by: Bin Meng

Kconfig: Convert CONFIG_RTC_MC146818 to Kconfig

2018-10-09T10:40:27+00:00

Move this option to Kconfig and tidy up the two boards which use it. Signed-off-by: Simon Glass

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini