starfive-tech/u-boot.git/include/configs/dreamplug.h, branch rtthread_AMP

arm: kirkwood: Dreamplug: Add DM SATA and remove IDE configs

2021-07-31T07:59:59+00:00

- Enable DM SATA, removed IDE driver, and add SATA MV driver. - Use ethernet PHY names from device tree in default boot command Signed-off-by: Tony Dinh Reviewed-by: Stefan Roese

drivers: ata: Remove mvsata_ide driver

2021-04-10T11:59:30+00:00

The mvsata_ide driver was due for DM conversion by v2019.07. As that has long passed, remove the driver and disable it in the boards which had enabled it. Signed-off-by: Tom Rini

Convert CONFIG_CMD_ASKENV et al to Kconfig

2020-06-04T22:10:02+00:00

This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

cosmetic: config: Remove empty #ifdefs

2019-04-02T11:44:18+00:00

After running tools/moveconfig.py it turned out that for various boards there are an empty #ifdef statements. Remove them to clean u-boot source code. Signed-off-by: Lukasz Majewski

Convert CONFIG_ENV_SPI_* to Kconfig

2019-03-25T21:36:59+00:00

This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay

arm: kirkwood: configs: dreamplug: Convert to DM_SPI

2018-11-30T09:58:10+00:00

Enable CONFIG_DM_SPI=y and CONFIG_DM_SPI_FLASH=y in the defconfig. Signed-off-by: Chris Packham Reviewed-by: Stefan Roese Signed-off-by: Stefan Roese

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

spi: Migrate CONFIG_KIRKWOOD_SPI to Kconfig

2018-02-14T04:01:44+00:00

Signed-off-by: Tuomas Tynkkynen

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

2017-07-26T01:31:03+00:00

This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: Simon Glass