starfive-tech/u-boot.git/drivers/net/Kconfig, branch rtthread_AMP

net: dwc_eth_qos:starfive: add jh7110 support

2022-10-18T08:24:34+00:00

Add new configuration for jh7110 soc platform. Signed-off-by: yanhong.wang

pci: Drop DM_PCI

2021-09-13T22:23:13+00:00

This option has not effect now. Drop it, using PCI instead where needed. Signed-off-by: Simon Glass

net: fec_mxc: support i.MX8ULP

2021-08-09T12:46:50+00:00

Support i.MX8ULP in fec_mxc Signed-off-by: Peng Fan Reviewed-by: Ramon Fried

net: xilinx: axi_mrmac: Add MRMAC driver

2021-07-26T07:18:45+00:00

Add support for xilinx multirate(MRMAC) ethernet driver. This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC. Added support for 4 ports of MRMAC for speeds 10G and 25G. MCDMA supports upto 16 channels but in this driver we have setup only one channel which is enough. Tested 10G and 25G on all 4 ports. Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek

net: dwc_eth_qos: use generic ethernet phy for stm32 variant

2021-07-22T19:05:44+00:00

Use the generic ethernet phy which already manages the correct binding for gpio reset, including the assert an deassert delays. Reviewed-by: Ramon Fried Signed-off-by: Patrick Delaunay

net: add support for KSZ9477/KSZ9897/KSZ9567 GbE switch

2021-07-10T16:12:42+00:00

The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO. This driver currently supports I2C register access but SPI or MDIO register access can be easily added at a later time. Tagging is not implemented and instead the active port is tracked to avoid needing a tag to store port information. This was tested with the imx8mm-venice-gw7901 board which has a KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID. Signed-off-by: Tim Harvey Reviewed-by: Ramon Fried

ppc: Remove T4160RDB board

2021-07-07T23:52:24+00:00

This board has not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove it. As this is the last ARCH_T4160 platform, remove that support as well. Signed-off-by: Tom Rini

ppc: Remove T1023RBD boards and T1024RDB_SECURE_BOOT

2021-07-07T23:52:23+00:00

These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the only ARCH_T1023 platform left, remove that support as well. Cc: Priyanka Jain Signed-off-by: Tom Rini

net: smc911x: Drop redundant CONFIG_SMC911X_16_BIT Kconfig symbol

2021-07-06T02:22:41+00:00

The SMC911x Ethernet driver needs to know which accessor functions it can use to access the MMIO registers. For that reason we have a Kconfig choice between 16 and 32-bit bus width. Since it's only those two options that we (and the Linux kernel) support, and there does not seem to be any evidence of another bus width anywhere, limit the Kconfig construct to a simple symbol. This simplifies the code and allows a later rework to be much easier. Signed-off-by: Andre Przywara Reviewed-by: Ramon Fried

net: synquacer: Add netsec driver

2021-06-18T08:29:17+00:00

Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y. Signed-off-by: Jassi Brar Reviewed-by: Ramon Fried