starfive-tech/u-boot.git/drivers/mmc/Kconfig, branch rtthread_AMP

drivers: mmc: fsl_esdhc_imx: support i.MX8ULP

2021-08-09T12:46:51+00:00

i.MX8ULP reuse same SDHC IP as i.MX8M, so follow i.MX8M code logic. Signed-off-by: Peng Fan

Merge branch '2021-07-06-platform-updates'

2021-07-06T22:10:10+00:00

- mpc8379erdb DM_USB, DM_PCI and DM_ETH support. - Drop PCI support from the integrator family of boards - Add synquacer support - Assorted lpc32xx updates and improvements - snapdragon (and related) fixes, Broadcom iproc update

mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver

2021-07-06T18:07:36+00:00

Signed-off-by: Jassi Brar Signed-off-by: Masami Hiramatsu Reviewed-by: Jaehoon Chung

mmc: openpiton: add piton_mmc driver

2021-07-06T05:50:56+00:00

This commit adds support to piton_mmc driver for OpenPiton-riscv64 This driver has many things set as preconfigured because the hardware automatically configures most of the settings during startup. Signed-off-by: Tianrui Wei Signed-off-by: Jonathan Balkind Reviewed-by: Jaehoon Chung

mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT

2021-06-17T06:16:11+00:00

For eSDHC, power supply is through peripheral circuit. Some eSDHC versions have value 0 of the bit but that does not reflect the truth. 3.3V is common for SD/MMC, and is supported for all boards with eSDHC in current u-boot. So, make 3.3V is supported in default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if future board does not support 3.3V. This is also a fix-up for one previous patch, which converted to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 that is not a Kconfig option. Fixes: 52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") Signed-off-by: Yangbo Lu Reviewed-by: Jaehoon Chung Reviewed-by: Priyanka Jain

DM: DM_MMC migration is now mandatory for non-SPL

2021-05-11T13:16:59+00:00

As it has been now two years past the migration deadline, it is required to have migrated. Remove the check from the Makefile and rework some of the Kconfig logic slightly to get the functional dependencies of DM_MMC / BLK right in both the SPL and non-SPL case. Signed-off-by: Tom Rini

mmc: octeontx_hsmmc: Add support for MIPS Octeon

2021-04-22T00:47:57+00:00

Until now, the Octeontx MMC driver did only support the ARM Octeon TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform to this driver. Here a short summary of the changes: - Enable driver compilation for MIPS Octeon, including the MMC related header file - Reorder header inclusion - Switch to using the clk framework to get the input clock - Remove some functions for MIPS Octeon, as some registers don't exist here Signed-off-by: Stefan Roese Cc: Peng Fan Cc: Aaron Williams Cc: Chandrakala Chavva Cc: Daniel Schwierzeck

arm: Remove s32v234evb board

2021-04-10T12:01:00+00:00

This board has not been converted to CONFIG_DM_MMC by the deadline. Remove it. Cc: Eddy Petrișor Signed-off-by: Tom Rini

mmc: mvebu: convert to driver model

2021-04-08T06:50:52+00:00

This is a straightforward conversion of the old, non-dm driver. It was done in-place as the deadline for non-dm MMC has passed. Previous commits ensured that no board depends on the old, non-dm variant. Tested on a Kirkwood based board with eMMC. Signed-off-by: Harm Berntsen Tested-by: Harm Berntsen Reviewed-by: Simon Glass Reviewed-by: Stefan Roese CC: Pantelis Antoniou CC: Stefan Roese CC: Gerald Kerma CC: Simon Glass Reviewed-by: Jaehoon Chung

mmc: fsl_esdhc: add pulse width detection workaround

2021-04-06T10:36:04+00:00

HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a workaroung for the pulse width detection. Apply this workaround in u-boot, too. This will make HS400 mode work reliably on the LS1028A SoC. Signed-off-by: Michael Walle Reviewed-by: Jaehoon Chung