1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
|
// SPDX-License-Identifier: GPL-2.0-only
/*
* pata_mpiix.c - Intel MPIIX PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
* Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* The MPIIX is different enough to the PIIX4 and friends that we give it
* a separate driver. The old ide/pci code handles this by just not tuning
* MPIIX at all.
*
* The MPIIX also differs in another important way from the majority of PIIX
* devices. The chip is a bridge (pardon the pun) between the old world of
* ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual
* IDE controller is not decoded in PCI space and the chip does not claim to
* be IDE class PCI. This requires slightly non-standard probe logic compared
* with PCI IDE and also that we do not disable the device when our driver is
* unloaded (as it has many other functions).
*
* The driver consciously keeps this logic internally to avoid pushing quirky
* PATA history into the clean libata layer.
*
* Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA
* hard disk present this driver will not detect it. This is not a bug. In this
* configuration the secondary port of the MPIIX is disabled and the addresses
* are decoded by the PCMCIA bridge and therefore are for a generic IDE driver
* to operate.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
#define DRV_VERSION "0.7.7"
enum {
IDETIM = 0x6C, /* IDE control register */
IORDY = (1 << 1),
PPE = (1 << 2),
FTIM = (1 << 0),
ENABLED = (1 << 15),
SECONDARY = (1 << 14)
};
static int mpiix_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* mpiix_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. The MPIIX allows us to program the
* IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether
* prefetching or IORDY are used.
*
* This would get very ugly because we can only program timing for one
* device at a time, the other gets PIO0. Fortunately libata calls
* our qc_issue command before a command is issued so we can flip the
* timings back and forth to reduce the pain.
*/
static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
int control = 0;
int pio = adev->pio_mode - XFER_PIO_0;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 idetim;
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
pci_read_config_word(pdev, IDETIM, &idetim);
/* Mask the IORDY/TIME/PPE for this device */
if (adev->class == ATA_DEV_ATA)
control |= PPE; /* Enable prefetch/posting for disk */
if (ata_pio_need_iordy(adev))
control |= IORDY;
if (pio > 1)
control |= FTIM; /* This drive is on the fast timing bank */
/* Mask out timing and clear both TIME bank selects */
idetim &= 0xCCEE;
idetim &= ~(0x07 << (4 * adev->devno));
idetim |= control << (4 * adev->devno);
idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
pci_write_config_word(pdev, IDETIM, idetim);
/* We use ap->private_data as a pointer to the device currently
loaded for timing */
ap->private_data = adev;
}
/**
* mpiix_qc_issue - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
* necessary. Our logic also clears TIME0/TIME1 for the other device so
* that, even if we get this wrong, cycles to the other device will
* be made PIO0.
*/
static unsigned int mpiix_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
/* If modes have been configured and the channel data is not loaded
then load it. We have to check if pio_mode is set as the core code
does not set adev->pio_mode to XFER_PIO_0 while probing as would be
logical */
if (adev->pio_mode && adev != ap->private_data)
mpiix_set_piomode(ap, adev);
return ata_sff_qc_issue(qc);
}
static const struct scsi_host_template mpiix_sht = {
ATA_PIO_SHT(DRV_NAME),
};
static struct ata_port_operations mpiix_port_ops = {
.inherits = &ata_sff_port_ops,
.qc_issue = mpiix_qc_issue,
.cable_detect = ata_cable_40wire,
.set_piomode = mpiix_set_piomode,
.prereset = mpiix_pre_reset,
.sff_data_xfer = ata_sff_data_xfer32,
};
static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* Single threaded by the PCI probe logic */
struct ata_host *host;
struct ata_port *ap;
void __iomem *cmd_addr, *ctl_addr;
u16 idetim;
int cmd, ctl, irq;
ata_print_version_once(&dev->dev, DRV_VERSION);
host = ata_host_alloc(&dev->dev, 1);
if (!host)
return -ENOMEM;
ap = host->ports[0];
/* MPIIX has many functions which can be turned on or off according
to other devices present. Make sure IDE is enabled before we try
and use it */
pci_read_config_word(dev, IDETIM, &idetim);
if (!(idetim & ENABLED))
return -ENODEV;
/* See if it's primary or secondary channel... */
if (!(idetim & SECONDARY)) {
cmd = 0x1F0;
ctl = 0x3F6;
irq = 14;
} else {
cmd = 0x170;
ctl = 0x376;
irq = 15;
}
cmd_addr = devm_ioport_map(&dev->dev, cmd, 8);
ctl_addr = devm_ioport_map(&dev->dev, ctl, 1);
if (!cmd_addr || !ctl_addr)
return -ENOMEM;
ata_port_desc(ap, "cmd 0x%x ctl 0x%x", cmd, ctl);
/* We do our own plumbing to avoid leaking special cases for whacko
ancient hardware into the core code. There are two issues to
worry about. #1 The chip is a bridge so if in legacy mode and
without BARs set fools the setup. #2 If you pci_disable_device
the MPIIX your box goes castors up */
ap->ops = &mpiix_port_ops;
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = cmd_addr;
ap->ioaddr.ctl_addr = ctl_addr;
ap->ioaddr.altstatus_addr = ctl_addr;
/* Let libata fill in the port details */
ata_sff_std_ports(&ap->ioaddr);
/* activate host */
return ata_host_activate(host, irq, ata_sff_interrupt, IRQF_SHARED,
&mpiix_sht);
}
static const struct pci_device_id mpiix[] = {
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
{ },
};
static struct pci_driver mpiix_pci_driver = {
.name = DRV_NAME,
.id_table = mpiix,
.probe = mpiix_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
module_pci_driver(mpiix_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, mpiix);
MODULE_VERSION(DRV_VERSION);
|
