1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
|
// SPDX-License-Identifier: GPL-2.0-only
/*
* Intel CE4100 platform specific setup code
*
* (C) Copyright 2010 Intel Corporation
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/reboot.h>
#include <linux/serial_reg.h>
#include <linux/serial_8250.h>
#include <asm/ce4100.h>
#include <asm/prom.h>
#include <asm/setup.h>
#include <asm/i8259.h>
#include <asm/io.h>
#include <asm/io_apic.h>
#include <asm/emergency-restart.h>
/*
* The CE4100 platform has an internal 8051 Microcontroller which is
* responsible for signaling to the external Power Management Unit the
* intention to reset, reboot or power off the system. This 8051 device has
* its command register mapped at I/O port 0xcf9 and the value 0x4 is used
* to power off the system.
*/
static void ce4100_power_off(void)
{
outb(0x4, 0xcf9);
}
#ifdef CONFIG_SERIAL_8250
static unsigned int mem_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return readl(p->membase + offset);
}
/*
* The UART Tx interrupts are not set under some conditions and therefore serial
* transmission hangs. This is a silicon issue and has not been root caused. The
* workaround for this silicon issue checks UART_LSR_THRE bit and UART_LSR_TEMT
* bit of LSR register in interrupt handler to see whether at least one of these
* two bits is set, if so then process the transmit request. If this workaround
* is not applied, then the serial transmission may hang. This workaround is for
* errata number 9 in Errata - B step.
*/
static unsigned int ce4100_mem_serial_in(struct uart_port *p, int offset)
{
unsigned int ret, ier, lsr;
if (offset == UART_IIR) {
offset = offset << p->regshift;
ret = readl(p->membase + offset);
if (ret & UART_IIR_NO_INT) {
/* see if the TX interrupt should have really set */
ier = mem_serial_in(p, UART_IER);
/* see if the UART's XMIT interrupt is enabled */
if (ier & UART_IER_THRI) {
lsr = mem_serial_in(p, UART_LSR);
/* now check to see if the UART should be
generating an interrupt (but isn't) */
if (lsr & (UART_LSR_THRE | UART_LSR_TEMT))
ret &= ~UART_IIR_NO_INT;
}
}
} else
ret = mem_serial_in(p, offset);
return ret;
}
static void ce4100_mem_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
writel(value, p->membase + offset);
}
static void ce4100_serial_fixup(int port, struct uart_port *up,
u32 *capabilities)
{
#ifdef CONFIG_EARLY_PRINTK
/*
* Over ride the legacy port configuration that comes from
* asm/serial.h. Using the ioport driver then switching to the
* PCI memmaped driver hangs the IOAPIC
*/
if (up->iotype != UPIO_MEM32) {
up->uartclk = 14745600;
up->mapbase = 0xdffe0200;
set_fixmap_nocache(FIX_EARLYCON_MEM_BASE,
up->mapbase & PAGE_MASK);
up->membase =
(void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE);
up->membase += up->mapbase & ~PAGE_MASK;
up->mapbase += port * 0x100;
up->membase += port * 0x100;
up->iotype = UPIO_MEM32;
up->regshift = 2;
up->irq = 4;
}
#endif
up->iobase = 0;
up->serial_in = ce4100_mem_serial_in;
up->serial_out = ce4100_mem_serial_out;
*capabilities |= (1 << 12);
}
static __init void sdv_serial_fixup(void)
{
serial8250_set_isa_configurator(ce4100_serial_fixup);
}
#else
static inline void sdv_serial_fixup(void) {};
#endif
static void __init sdv_arch_setup(void)
{
sdv_serial_fixup();
}
static void sdv_pci_init(void)
{
x86_of_pci_init();
}
/*
* CE4100 specific x86_init function overrides and early setup
* calls.
*/
void __init x86_ce4100_early_setup(void)
{
x86_init.oem.arch_setup = sdv_arch_setup;
x86_init.resources.probe_roms = x86_init_noop;
x86_init.mpparse.get_smp_config = x86_init_uint_noop;
x86_init.mpparse.find_smp_config = x86_init_noop;
x86_init.mpparse.setup_ioapic_ids = setup_ioapic_ids_from_mpc_nocheck;
x86_init.pci.init = ce4100_pci_init;
x86_init.pci.init_irq = sdv_pci_init;
/*
* By default, the reboot method is ACPI which is supported by the
* CE4100 bootloader CEFDK using FADT.ResetReg Address and ResetValue
* the bootloader will however issue a system power off instead of
* reboot. By using BOOT_KBD we ensure proper system reboot as
* expected.
*/
reboot_type = BOOT_KBD;
pm_power_off = ce4100_power_off;
}
|
