1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
|
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the RZA2MEVB board
*
* Copyright (C) 2018 Renesas Electronics
*
* As upstream Linux does not support XIP, it cannot run in 8 MiB of HyperRAM.
* Hence the 64 MiB of SDRAM on the sub-board needs to be enabled, which has
* the following ramifications:
* - SCIF4 connected to the on-board USB-serial can no longer be used as the
* serial console,
* - Instead, SCIF2 is used as the serial console, by connecting a 3.3V TTL
* USB-to-Serial adapter to the CMOS camera connector:
* - RXD = CN17-9,
* - TXD = CN17-10,
* - GND = CN17-2 or CN17-17,
* - The first Ethernet channel can no longer be used,
* - USB Channel 1 loses the overcurrent input signal.
*
* Please make sure your sub-board matches the following switch settings:
*
* SW6 SW6-1 set to SDRAM
* ON SW6-2 set to Audio
* +---------------------+ SW6-3 set to DRP
* | = = = = = | SW6-4 set to CEU
* | = = | SW6-5 set to Ether2
* | 1 2 3 4 5 6 7 8 9 0 | SW6-6 set to VDC6
* +---------------------+ SW6-7 set to VDC6
*/
/dts-v1/;
#include "r7s9210.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/r7s9210-pinctrl.h>
/ {
model = "RZA2MEVB";
compatible = "renesas,rza2mevb", "renesas,r7s9210";
aliases {
serial0 = &scif2;
ethernet0 = ðer1;
};
chosen {
bootargs = "ignore_loglevel";
stdout-path = "serial0:115200n8";
};
keyboard {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&keyboard_pins>;
key-3 {
interrupt-parent = <&irqc>;
interrupts = <0 IRQ_TYPE_EDGE_BOTH>;
linux,code = <KEY_3>;
label = "SW3";
wakeup-source;
};
};
lbsc {
#address-cells = <1>;
#size-cells = <1>;
};
leds {
compatible = "gpio-leds";
red {
gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
};
green {
gpios = <&pinctrl RZA2_PIN(PORTC, 1) GPIO_ACTIVE_HIGH>;
};
};
memory@c000000 {
device_type = "memory";
reg = <0x0c000000 0x04000000>; /* SDRAM */
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
ðer1 {
pinctrl-names = "default";
pinctrl-0 = <ð1_pins>;
status = "okay";
renesas,no-ether-link;
phy-handle = <&phy1>;
phy1: ethernet-phy@1 {
compatible = "ethernet-phy-id001c.c816",
"ethernet-phy-ieee802.3-c22";
reg = <0>;
};
};
/* EXTAL */
&extal_clk {
clock-frequency = <24000000>; /* 24MHz */
};
&i2c3 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
eeprom@50 {
compatible = "renesas,r1ex24128", "atmel,24c128";
reg = <0x50>;
pagesize = <64>;
};
};
/* High resolution System tick timers */
&ostm0 {
status = "okay";
};
&ostm1 {
status = "okay";
};
&pinctrl {
eth0_pins: eth0 {
pinmux = <RZA2_PINMUX(PORTE, 0, 7)>, /* REF50CK0 */
<RZA2_PINMUX(PORT6, 1, 7)>, /* RMMI0_TXDEN */
<RZA2_PINMUX(PORT6, 2, 7)>, /* RMII0_TXD0 */
<RZA2_PINMUX(PORT6, 3, 7)>, /* RMII0_TXD1 */
<RZA2_PINMUX(PORTE, 4, 7)>, /* RMII0_CRSDV */
<RZA2_PINMUX(PORTE, 1, 7)>, /* RMII0_RXD0 */
<RZA2_PINMUX(PORTE, 2, 7)>, /* RMII0_RXD1 */
<RZA2_PINMUX(PORTE, 3, 7)>, /* RMII0_RXER */
<RZA2_PINMUX(PORTE, 5, 1)>, /* ET0_MDC */
<RZA2_PINMUX(PORTE, 6, 1)>, /* ET0_MDIO */
<RZA2_PINMUX(PORTL, 0, 5)>; /* IRQ4 */
};
eth1_pins: eth1 {
pinmux = <RZA2_PINMUX(PORTK, 3, 7)>, /* REF50CK1 */
<RZA2_PINMUX(PORTK, 0, 7)>, /* RMMI1_TXDEN */
<RZA2_PINMUX(PORTK, 1, 7)>, /* RMII1_TXD0 */
<RZA2_PINMUX(PORTK, 2, 7)>, /* RMII1_TXD1 */
<RZA2_PINMUX(PORT3, 2, 7)>, /* RMII1_CRSDV */
<RZA2_PINMUX(PORTK, 4, 7)>, /* RMII1_RXD0 */
<RZA2_PINMUX(PORT3, 5, 7)>, /* RMII1_RXD1 */
<RZA2_PINMUX(PORT3, 1, 7)>, /* RMII1_RXER */
<RZA2_PINMUX(PORT3, 3, 1)>, /* ET1_MDC */
<RZA2_PINMUX(PORT3, 4, 1)>, /* ET1_MDIO */
<RZA2_PINMUX(PORTL, 1, 5)>; /* IRQ5 */
};
i2c3_pins: i2c3 {
pinmux = <RZA2_PINMUX(PORTD, 6, 1)>, /* RIIC3SCL */
<RZA2_PINMUX(PORTD, 7, 1)>; /* RIIC3SDA */
};
keyboard_pins: keyboard {
pinmux = <RZA2_PINMUX(PORTJ, 1, 6)>; /* IRQ0 */
};
/* Serial Console */
scif2_pins: serial2 {
pinmux = <RZA2_PINMUX(PORTE, 2, 3)>, /* TxD2 */
<RZA2_PINMUX(PORTE, 1, 3)>; /* RxD2 */
};
sdhi0_pins: sdhi0 {
pinmux = <RZA2_PINMUX(PORT5, 0, 3)>, /* SD0_CD */
<RZA2_PINMUX(PORT5, 1, 3)>; /* SD0_WP */
};
sdhi1_pins: sdhi1 {
pinmux = <RZA2_PINMUX(PORT5, 4, 3)>, /* SD1_CD */
<RZA2_PINMUX(PORT5, 5, 3)>; /* SD1_WP */
};
usb0_pins: usb0 {
pinmux = <RZA2_PINMUX(PORT5, 2, 3)>, /* VBUSIN0 */
<RZA2_PINMUX(PORTC, 6, 1)>, /* VBUSEN0 */
<RZA2_PINMUX(PORTC, 7, 1)>; /* OVRCUR0 */
};
usb1_pins: usb1 {
pinmux = <RZA2_PINMUX(PORTC, 0, 1)>, /* VBUSIN1 */
<RZA2_PINMUX(PORTC, 5, 1)>; /* VBUSEN1 */
};
};
/* RTC_X1 */
&rtc_x1_clk {
clock-frequency = <32768>;
};
/* Serial Console */
&scif2 {
pinctrl-names = "default";
pinctrl-0 = <&scif2_pins>;
status = "okay";
};
&sdhi0 {
pinctrl-names = "default";
pinctrl-0 = <&sdhi0_pins>;
bus-width = <4>;
status = "okay";
};
&sdhi1 {
pinctrl-names = "default";
pinctrl-0 = <&sdhi1_pins>;
bus-width = <4>;
status = "okay";
};
/* USB-0 as Host */
&usb2_phy0 {
pinctrl-names = "default";
pinctrl-0 = <&usb0_pins>;
dr_mode = "host"; /* Requires JP3 to be fitted */
status = "okay";
};
/* USB-1 as Host */
&usb2_phy1 {
pinctrl-names = "default";
pinctrl-0 = <&usb1_pins>;
dr_mode = "host";
status = "okay";
};
/* USB_X1 */
&usb_x1_clk {
clock-frequency = <48000000>;
};
|
