1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
|
Qualcomm QUSB2 phy controller
=============================
QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
Required properties:
- compatible: compatible list, contains
"qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
"qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.
- reg: offset and length of the PHY register set.
- #phy-cells: must be 0.
- clocks: a list of phandles and clock-specifier pairs,
one for each entry in clock-names.
- clock-names: must be "cfg_ahb" for phy config clock,
"ref" for 19.2 MHz ref clk,
"iface" for phy interface clock (Optional).
- vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
- vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
- resets: Phandle to reset to phy block.
Optional properties:
- nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
tuning parameter value for qusb2 phy.
- qcom,tcsr-syscon: Phandle to TCSR syscon register region.
- qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
tuning parameter that may vary for different boards of same SOC.
This property is applicable to only QUSB2 v2 PHY (sdm845).
- qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
output current.
Possible range is - 15mA to 24mA (stepsize of 600 uA).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
This property is applicable to only QUSB2 v2 PHY (sdm845).
Default value is 22.2mA for sdm845.
- qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
Possible range is 0 to 15% (stepsize of 5%).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
This property is applicable to only QUSB2 v2 PHY (sdm845).
Default value is 10% for sdm845.
- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
pre-emphasis (specified using qcom,preemphasis-level) must be in
effect. Duration could be half-bit of full-bit.
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
This property is applicable to only QUSB2 v2 PHY (sdm845).
Default value is full-bit width for sdm845.
Example:
hsusb_phy: phy@7411000 {
compatible = "qcom,msm8996-qusb2-phy";
reg = <0x7411000 0x180>;
#phy-cells = <0>;
clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
<&gcc GCC_RX1_USB2_CLKREF_CLK>,
clock-names = "cfg_ahb", "ref";
vdda-pll-supply = <&pm8994_l12>;
vdda-phy-dpdm-supply = <&pm8994_l24>;
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
nvmem-cells = <&qusb2p_hstx_trim>;
};
|
