1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
Generic device tree bindings for I3C busses
===========================================
This document describes generic bindings that should be used to describe I3C
busses in a device tree.
Required properties
-------------------
- #address-cells - should be <3>. Read more about addresses below.
- #size-cells - should be <0>.
- compatible - name of the I3C master controller driving the I3C bus
For other required properties e.g. to describe register sets,
clocks, etc. check the binding documentation of the specific driver.
The node describing an I3C bus should be named i3c-master.
Optional properties
-------------------
These properties may not be supported by all I3C master drivers. Each I3C
master bindings should specify which of them are supported.
- i3c-scl-hz: frequency of the SCL signal used for I3C transfers.
When undefined the core sets it to 12.5MHz.
- i2c-scl-hz: frequency of the SCL signal used for I2C transfers.
When undefined, the core looks at LVR (Legacy Virtual Register)
values of I2C devices described in the device tree to determine
the maximum I2C frequency.
I2C devices
===========
Each I2C device connected to the bus should be described in a subnode. All
properties described in Documentation/devicetree/bindings/i2c/i2c.txt are
valid here, but several new properties have been added.
New constraint on existing properties:
--------------------------------------
- reg: contains 3 cells
+ first cell : still encoding the I2C address
+ second cell: shall be 0
+ third cell: shall encode the I3C LVR (Legacy Virtual Register)
bit[31:8]: unused/ignored
bit[7:5]: I2C device index. Possible values
* 0: I2C device has a 50 ns spike filter
* 1: I2C device does not have a 50 ns spike filter but supports high
frequency on SCL
* 2: I2C device does not have a 50 ns spike filter and is not tolerant
to high frequencies
* 3-7: reserved
bit[4]: tell whether the device operates in FM (Fast Mode) or FM+ mode
* 0: FM+ mode
* 1: FM mode
bit[3:0]: device type
* 0-15: reserved
The I2C node unit-address should always match the first cell of the reg
property: <device-type>@<i2c-address>.
I3C devices
===========
All I3C devices are supposed to support DAA (Dynamic Address Assignment), and
are thus discoverable. So, by default, I3C devices do not have to be described
in the device tree.
This being said, one might want to attach extra resources to these devices,
and those resources may have to be described in the device tree, which in turn
means we have to describe I3C devices.
Another use case for describing an I3C device in the device tree is when this
I3C device has a static I2C address and we want to assign it a specific I3C
dynamic address before the DAA takes place (so that other devices on the bus
can't take this dynamic address).
The I3C device should be names <device-type>@<static-i2c-address>,<i3c-pid>,
where device-type is describing the type of device connected on the bus
(gpio-controller, sensor, ...).
Required properties
-------------------
- reg: contains 3 cells
+ first cell : encodes the static I2C address. Should be 0 if the device does
not have one (0 is not a valid I2C address).
+ second and third cells: should encode the ProvisionalID. The second cell
contains the manufacturer ID left-shifted by 1.
The third cell contains ORing of the part ID
left-shifted by 16, the instance ID left-shifted
by 12 and the extra information. This encoding is
following the PID definition provided by the I3C
specification.
Optional properties
-------------------
- assigned-address: dynamic address to be assigned to this device. This
property is only valid if the I3C device has a static
address (first cell of the reg property != 0).
Example:
i3c-master@d040000 {
compatible = "cdns,i3c-master";
clocks = <&coreclock>, <&i3csysclock>;
clock-names = "pclk", "sysclk";
interrupts = <3 0>;
reg = <0x0d040000 0x1000>;
#address-cells = <3>;
#size-cells = <0>;
i2c-scl-hz = <100000>;
/* I2C device. */
nunchuk: nunchuk@52 {
compatible = "nintendo,nunchuk";
reg = <0x52 0x0 0x10>;
};
/* I3C device with a static I2C address. */
thermal_sensor: sensor@68,39200144004 {
reg = <0x68 0x392 0x144004>;
assigned-address = <0xa>;
};
/*
* I3C device without a static I2C address but requiring
* resources described in the DT.
*/
sensor@0,39200154004 {
reg = <0x0 0x392 0x154004>;
clocks = <&clock_provider 0>;
};
};
|
