blob: 8ec4a7f2623a30f9a51465577fbd05c14b8bc341 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
SN65DSI86 DSI to eDP bridge chip
--------------------------------
This is the binding for Texas Instruments SN65DSI86 bridge.
http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
Required properties:
- compatible: Must be "ti,sn65dsi86"
- reg: i2c address of the chip, 0x2d as per datasheet
- enable-gpios: gpio specification for bridge_en pin (active high)
- vccio-supply: A 1.8V supply that powers up the digital IOs.
- vpll-supply: A 1.8V supply that powers up the displayport PLL.
- vcca-supply: A 1.2V supply that powers up the analog circuits.
- vcc-supply: A 1.2V supply that powers up the digital core.
Optional properties:
- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
- gpio-controller: Marks the device has a GPIO controller.
- #gpio-cells : Should be two. The first cell is the pin number and
the second cell is used to specify flags.
See ../../gpio/gpio.txt for more information.
- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
the cell formats.
- clock-names: should be "refclk"
- clocks: Specification for input reference clock. The reference
clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
- data-lanes: See ../../media/video-interface.txt
- lane-polarities: See ../../media/video-interface.txt
- suspend-gpios: specification for GPIO1 pin on bridge (active low)
Required nodes:
This device has two video ports. Their connections are modelled using the
OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
- Video port 0 for DSI input
- Video port 1 for eDP output
Example
-------
edp-bridge@2d {
compatible = "ti,sn65dsi86";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x2d>;
enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
vccio-supply = <&pm8916_l17>;
vcca-supply = <&pm8916_l6>;
vpll-supply = <&pm8916_l17>;
vcc-supply = <&pm8916_l6>;
clock-names = "refclk";
clocks = <&input_refclk>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
edp_bridge_in: endpoint {
remote-endpoint = <&dsi_out>;
};
};
port@1 {
reg = <1>;
edp_bridge_out: endpoint {
data-lanes = <2 1 3 0>;
lane-polarities = <0 1 0 1>;
remote-endpoint = <&edp_panel_in>;
};
};
};
}
|
