/****************************************************************************** * * Copyright(c) 2003 - 2009 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify it * under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but WITHOUT * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for * more details. * * You should have received a copy of the GNU General Public License along with * this program; if not, write to the Free Software Foundation, Inc., * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA * * The full GNU General Public License is included in this distribution in the * file called LICENSE. * * Contact Information: * Intel Linux Wireless <ilw@linux.intel.com> * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 * *****************************************************************************/ #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> #include <linux/pci.h> #include <linux/dma-mapping.h> #include <linux/delay.h> #include <linux/skbuff.h> #include <linux/netdevice.h> #include <linux/wireless.h> #include <linux/firmware.h> #include <linux/etherdevice.h> #include <asm/unaligned.h> #include <net/mac80211.h> #include "iwl-fh.h" #include "iwl-3945-fh.h" #include "iwl-commands.h" #include "iwl-sta.h" #include "iwl-3945.h" #include "iwl-eeprom.h" #include "iwl-helpers.h" #include "iwl-core.h" #include "iwl-agn-rs.h" #define IWL_DECLARE_RATE_INFO(r, ip, in, rp, rn, pp, np) \ [IWL_RATE_##r##M_INDEX] = { IWL_RATE_##r##M_PLCP, \ IWL_RATE_##r##M_IEEE, \ IWL_RATE_##ip##M_INDEX, \ IWL_RATE_##in##M_INDEX, \ IWL_RATE_##rp##M_INDEX, \ IWL_RATE_##rn##M_INDEX, \ IWL_RATE_##pp##M_INDEX, \ IWL_RATE_##np##M_INDEX, \ IWL_RATE_##r##M_INDEX_TABLE, \ IWL_RATE_##ip##M_INDEX_TABLE } /* * Parameter order: * rate, prev rate, next rate, prev tgg rate, next tgg rate * * If there isn't a valid next or previous rate then INV is used which * maps to IWL_RATE_INVALID * */ const struct iwl3945_rate_info iwl3945_rates[IWL_RATE_COUNT_3945] = { IWL_DECLARE_RATE_INFO(1, INV, 2, INV, 2, INV, 2), /* 1mbps */ IWL_DECLARE_RATE_INFO(2, 1, 5, 1, 5, 1, 5), /* 2mbps */ IWL_DECLARE_RATE_INFO(5, 2, 6, 2, 11, 2, 11), /*5.5mbps */ IWL_DECLARE_RATE_INFO(11, 9, 12, 5, 12, 5, 18), /* 11mbps */ IWL_DECLARE_RATE_INFO(6, 5, 9, 5, 11, 5, 11), /* 6mbps */ IWL_DECLARE_RATE_INFO(9, 6, 11, 5, 11, 5, 11), /* 9mbps */ IWL_DECLARE_RATE_INFO(12, 11, 18, 11, 18, 11, 18), /* 12mbps */ IWL_DECLARE_RATE_INFO(18, 12, 24, 12, 24, 11, 24), /* 18mbps */ IWL_DECLARE_RATE_INFO(24, 18, 36, 18, 36, 18, 36), /* 24mbps */ IWL_DECLARE_RATE_INFO(36, 24, 48, 24, 48, 24, 48), /* 36mbps */ IWL_DECLARE_RATE_INFO(48, 36, 54, 36, 54, 36, 54), /* 48mbps */ IWL_DECLARE_RATE_INFO(54, 48, INV, 48, INV, 48, INV),/* 54mbps */ }; /* 1 = enable the iwl3945_disable_events() function */ #define IWL_EVT_DISABLE (0) #define IWL_EVT_DISABLE_SIZE (1532/32) /** * iwl3945_disable_events - Disable selected events in uCode event log * * Disable an event by writing "1"s into "disable" * bitmap in SRAM. Bit position corresponds to Event # (id/type). * Default values of 0 enable uCode events to be logged. * Use for only special debugging. This function is just a placeholder as-is, * you'll need to provide the special bits! ... * ... and set IWL_EVT_DISABLE to 1. */ void iwl3945_disable_events(struct iwl_priv *priv) { int i; u32 base; /* SRAM address of event log header */ u32 disable_ptr; /* SRAM address of event-disable bitmap array */ u32 array_size; /* # of u32 entries in array */ u32 evt_disable[IWL_EVT_DISABLE_SIZE] = { 0x00000000, /* 31 - 0 Event id numbers */ 0x00000000, /* 63 - 32 */ 0x00000000, /* 95 - 64 */ 0x00000000, /* 127 - 96 */ 0x00000000, /* 159 - 128 */ 0x00000000, /* 191 - 160 */ 0x00000000, /* 223 - 192 */ 0x00000000, /* 255 - 224 */ 0x00000000, /* 287 - 256 */ 0x00000000, /* 319 - 288 */ 0x00000000, /* 351 - 320 */ 0x00000000, /* 383 - 352 */ 0x00000000, /* 415 - 384 */ 0x00000000, /* 447 - 416 */ 0x00000000, /* 479 - 448 */ 0x00000000, /* 511 - 480 */ 0x00000000, /* 543 - 512 */ 0x00000000, /* 575 - 544 */ 0x00000000, /* 607 - 576 */ 0x00000000, /* 639 - 608 */ 0x00000000, /* 671 - 640 */ 0x00000000, /* 703 - 672 */ 0x00000000, /* 735 - 704 */ 0x00000000, /* 767 - 736 */ 0x00000000, /* 799 - 768 */ 0x00000000, /* 831 - 800 */ 0x00000000, /* 863 - 832 */ 0x00000000, /* 895 - 864 */ 0x00000000, /* 927 - 896 */ 0x00000000, /* 959 - 928 */ 0x00000000, /* 991 - 960 */ 0x00000000, /* 1023 - 992 */ 0x00000000, /* 1055 - 1024 */ 0x00000000, /* 1087 - 1056 */ 0x00000000, /* 1119 - 1088 */ 0x00000000, /* 1151 - 1120 */ 0x00000000, /* 1183 - 1152 */ 0x00000000, /* 1215 - 1184 */ 0x00000000, /* 1247 - 1216 */ 0x00000000, /* 1279 - 1248 */ 0x00000000, /* 1311 - 1280 */ 0x00000000, /* 1343 - 1312 */ 0x00000000, /* 1375 - 1344 */ 0x00000000, /* 1407 - 1376 */ 0x00000000, /* 1439 - 1408 */ 0x00000000, /* 1471 - 1440 */ 0x00000000, /* 1503 - 1472 */ }; base = le32_to_cpu(priv->card_alive.log_event_table_ptr); if (!iwl3945_hw_valid_rtc_data_addr(base)) { IWL_ERR(priv, "Invalid event log pointer 0x%08X\n", base); return; } disable_ptr = iwl_read_targ_mem(priv, base + (4 * sizeof(u32))); array_size = iwl_read_targ_mem(priv, base + (5 * sizeof(u32))); if (IWL_EVT_DISABLE && (array_size == IWL_EVT_DISABLE_SIZE)) { IWL_DEBUG_INFO(priv, "Disabling selected uCode log events at 0x%x\n", disable_ptr); for (i = 0; i < IWL_EVT_DISABLE_SIZE; i++) iwl_write_targ_mem(priv, disable_ptr + (i * sizeof(u32)), evt_disable[i]); } else { IWL_DEBUG_INFO(priv, "Selected uCode log events may be disabled\n"); IWL_DEBUG_INFO(priv, " by writing \"1\"s into disable bitmap\n"); IWL_DEBUG_INFO(priv, " in SRAM at 0x%x, size %d u32s\n", disable_ptr, array_size); } } static int iwl3945_hwrate_to_plcp_idx(u8 plcp) { int idx; for (idx = 0; idx < IWL_RATE_COUNT; idx++) if (iwl3945_rates[idx].plcp == plcp) return idx; return -1; } #ifdef CONFIG_IWLWIFI_DEBUG #define TX_STATUS_ENTRY(x) case TX_STATUS_FAIL_ ## x: return #x static const char *iwl3945_get_tx_fail_reason(u32 status) { switch (status & TX_STATUS_MSK) { case TX_STATUS_SUCCESS: return "SUCCESS"; TX_STATUS_ENTRY(SHORT_LIMIT); TX_STATUS_ENTRY(LONG_LIMIT); TX_STATUS_ENTRY(FIFO_UNDERRUN); TX_STATUS_ENTRY(MGMNT_ABORT); TX_STATUS_ENTRY(NEXT_FRAG); TX_STATUS_ENTRY(LIFE_EXPIRE); TX_STATUS_ENTRY(DEST_PS); TX_STATUS_ENTRY(ABORTED); TX_STATUS_ENTRY(BT_RETRY); TX_STATUS_ENTRY(STA_INVALID); TX_STATUS_ENTRY(FRAG_DROPPED); TX_STATUS_ENTRY(TID_DISABLE); TX_STATUS_ENTRY(FRAME_FLUSHED); TX_STATUS_ENTRY(INSUFFICIENT_CF_POLL); TX_STATUS_ENTRY(TX_LOCKED); TX_STATUS_ENTRY(NO_BEACON_ON_RADAR); } return "UNKNOWN"; } #else static inline const char *iwl3945_get_tx_fail_reason(u32 status) { return ""; } #endif /* * get ieee prev rate from rate scale table. * for A and B mode we need to overright prev * value */ int iwl3945_rs_next_rate(struct iwl_priv *priv, int rate) { int next_rate = iwl3945_get_prev_ieee_rate(rate); switch (priv->band) { case IEEE80211_BAND_5GHZ: if (rate == IWL_RATE_12M_INDEX) next_rate = IWL_RATE_9M_INDEX; else if (rate == IWL_RATE_6M_INDEX) next_rate = IWL_RATE_6M_INDEX; break; case IEEE80211_BAND_2GHZ: if (!(priv->sta_supp_rates & IWL_OFDM_RATES_MASK) && iwl_is_associated(priv)) { if (rate == IWL_RATE_11M_INDEX) next_rate = IWL_RATE_5M_INDEX; } break; default: break; } return next_rate; } /** * iwl3945_tx_queue_reclaim - Reclaim Tx queue entries already Tx'd * * When FW advances 'R' index, all entries between old and new 'R' index * need to be reclaimed. As result, some free space forms. If there is * enough free space (> low mark), wake the stack that feeds us. */ static void iwl3945_tx_queue_reclaim(struct iwl_priv *priv, int txq_id, int index) { struct iwl_tx_queue *txq = &priv->txq[txq_id]; struct iwl_queue *q = &txq->q; struct iwl_tx_info *tx_info; BUG_ON(txq_id == IWL_CMD_QUEUE_NUM); for (index = iwl_queue_inc_wrap(index, q->n_bd); q->read_ptr != index; q->read_ptr = iwl_queue_inc_wrap(q->read_ptr, q->n_bd)) { tx_info = &txq->txb[txq->q.read_ptr]; ieee80211_tx_status_irqsafe(priv->hw, tx_info->skb[0]); tx_info->skb[0] = NULL; priv->cfg->ops->lib->txq_free_tfd(priv, txq); } if (iwl_queue_space(q) > q->low_mark && (txq_id >= 0) && (txq_id != IWL_CMD_QUEUE_NUM) && priv->mac80211_registered) iwl_wake_queue(priv, txq_id); } /** * iwl3945_rx_reply_tx - Handle Tx response */ static void iwl3945_rx_reply_tx(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb) { struct iwl_rx_packet *pkt = (void *)rxb->skb->data; u16 sequence = le16_to_cpu(pkt->hdr.sequence); int txq_id = SEQ_TO_QUEUE(sequence); int index = SEQ_TO_INDEX(sequence); struct iwl_tx_queue *txq = &priv->txq[txq_id]; struct ieee80211_tx_info *info; struct iwl3945_tx_resp *tx_resp = (void *)&pkt->u.raw[0]; u32 status = le32_to_cpu(tx_resp->status); int rate_idx; int fail; if ((index >= txq->q.n_bd) || (iwl_queue_used(&txq->q, index) == 0)) { IWL_ERR(priv, "Read index for DMA queue txq_id (%d) index %d " "is out of range [0-%d] %d %d\n", txq_id, index, txq->q.n_bd, txq->q.write_ptr, txq->q.read_ptr); return; } info = IEEE80211_SKB_CB(txq->txb[txq->q.read_ptr].skb[0]); ieee80211_tx_info_clear_status(info); /* Fill the MRR chain with some info about on-chip retransmissions */ rate_idx = iwl3945_hwrate_to_plcp_idx(tx_resp->rate); if (info->band == IEEE80211_BAND_5GHZ) rate_idx -= IWL_FIRST_OFDM_RATE; fail = tx_resp->failure_frame; info->status.rates[0].idx = rate_idx; info->status.rates[0].count = fail + 1; /* add final attempt */ /* tx_status->rts_retry_count = tx_resp->failure_rts; */ info->flags |= ((status & TX_STATUS_MSK) == TX_STATUS_SUCCESS) ? IEEE80211_TX_STAT_ACK : 0; IWL_DEBUG_TX(priv, "Tx queue %d Status %s (0x%08x) plcp rate %d retries %d\n", txq_id, iwl3945_get_tx_fail_reason(status), status, tx_resp->rate, tx_resp->failure_frame); IWL_DEBUG_TX_REPLY(priv, "Tx queue reclaim %d\n", index); iwl3945_tx_queue_reclaim(priv, txq_id, index); if (iwl_check_bits(status, TX_ABORT_REQUIRED_MSK)) IWL_ERR(priv, "TODO: Implement Tx ABORT REQUIRED!!!\n"); } /***************************************************************************** * * Intel PRO/Wireless 3945ABG/BG Network Connection * * RX handler implementations * *****************************************************************************/ void iwl3945_hw_rx_statistics(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb) { struct iwl_rx_packet *pkt = (void *)rxb->skb->data; IWL_DEBUG_RX(priv, "Statistics notification received (%d vs %d).\n", (int)sizeof(struct iwl3945_notif_statistics), le32_to_cpu(pkt->len)); memcpy(&priv->statistics_39, pkt->u.raw, sizeof(priv->statistics_39)); iwl3945_led_background(priv); priv->last_statistics_time = jiffies; } /****************************************************************************** * * Misc. internal state and helper functions * ******************************************************************************/ #ifdef CONFIG_IWLWIFI_DEBUG /** * iwl3945_report_frame - dump frame to syslog during debug sessions * * You may hack this function to show different aspects of received frames, * including selective frame dumps. * group100 parameter selects whether to show 1 out of 100 good frames. */ static void _iwl3945_dbg_report_frame(struct iwl_priv *priv, struct iwl_rx_packet *pkt, struct ieee80211_hdr *header, int group100) { u32 to_us; u32 print_summary = 0; u32 print_dump = 0; /* set to 1 to dump all frames' contents */ u32 hundred = 0; u32 dataframe = 0; __le16 fc; u16 seq_ctl; u16 channel; u16 phy_flags; u16 length; u16 status; u16 bcn_tmr; u32 tsf_low; u64 tsf; u8 rssi; u8 agc; u16 sig_avg; u16 noise_diff; struct iwl3945_rx_frame_stats *rx_stats = IWL_RX_STATS(pkt); struct iwl3945_rx_frame_hdr *rx_hdr = IWL_RX_HDR(pkt); struct iwl3945_rx_frame_end *rx_end = IWL_RX_END(pkt); u8 *data = IWL_RX_DATA(pkt); /* MAC header */ fc = header->frame_control; seq_ctl = le16_to_cpu(header->seq_ctrl); /* metadata */ channel = le16_to_cpu(rx_hdr->channel); phy_flags = le16_to_cpu(rx_hdr->phy_flags); length = le16_to_cpu(rx_hdr->len); /* end-of-frame status and timestamp */ status = le32_to_cpu(rx_end->status); bcn_tmr = le32_to_cpu(rx_end->beacon_timestamp); tsf_low = le64_to_cpu(rx_end->timestamp) & 0x0ffffffff; tsf = le64_to_cpu(rx_end->timestamp); /* signal statistics */ rssi = rx_stats->rssi; agc = rx_stats->agc; sig_avg = le16_to_cpu(rx_stats->sig_avg); noise_diff = le16_to_cpu(rx_stats->noise_diff); to_us = !compare_ether_addr(header->addr1, priv->mac_addr); /* if data frame is to us and all is good, * (optionally) print summary for only 1 out of every 100 */ if (to_us && (fc & ~cpu_to_le16(IEEE80211_FCTL_PROTECTED)) == cpu_to_le16(IEEE80211_FCTL_FROMDS | IEEE80211_FTYPE_DATA)) { dataframe = 1; if (!group100) print_summary = 1; /* print each frame */ else if (priv->framecnt_to_us < 100) { priv->framecnt_to_us++; print_summary = 0; } else { priv->framecnt_to_us = 0; print_summary = 1; hundred = 1; } } else { /* print summary for all other frames */ print_summary = 1; } if (print_summary) { char *title; int rate; if (hundred) title = "100Frames"; else if (ieee80211_has_retry(fc)) title = "Retry"; else if (ieee80211_is_assoc_resp(fc)) title = "AscRsp"; else if (ieee80211_is_reassoc_resp(fc)) title = "RasRsp"; else if (ieee80211_is_probe_resp(fc)) { title = "PrbRsp"; print_dump = 1; /* dump frame contents */ } else if (ieee80211_is_beacon(fc)) { title = "Beacon"; print_dump = 1; /* dump frame contents */ } else if (ieee80211_is_atim(fc)) title = "ATIM"; else if (ieee80211_is_auth(fc)) title = "Auth"; else if (ieee80211_is_deauth(fc)) title = "DeAuth"; else if (ieee80211_is_disassoc(fc)) title = "DisAssoc"; else title = "Frame"; rate = iwl3945_hwrate_to_plcp_idx(rx_hdr->rate); if (rate == -1) rate = 0; else rate = iwl3945_rates[rate].ieee / 2; /* print frame summary. * MAC addresses show just the last byte (for brevity), * but you can hack it to show more, if you'd like to. */ if (dataframe) IWL_DEBUG_RX(priv, "%s: mhd=0x%04x, dst=0x%02x, " "len=%u, rssi=%d, chnl=%d, rate=%d, \n", title, le16_to_cpu(fc), header->addr1[5], length, rssi, channel, rate); else { /* src/dst addresses assume managed mode */ IWL_DEBUG_RX(priv, "%s: 0x%04x, dst=0x%02x, " "src=0x%02x, rssi=%u, tim=%lu usec, " "phy=0x%02x, chnl=%d\n", title, le16_to_cpu(fc), header->addr1[5], header->addr3[5], rssi, tsf_low - priv->scan_start_tsf, phy_flags, channel); } } if (print_dump) iwl_print_hex_dump(priv, IWL_DL_RX, data, length); } static void iwl3945_dbg_report_frame(struct iwl_priv *priv, struct iwl_rx_packet *pkt, struct ieee80211_hdr *header, int group100) { if (priv->debug_level & IWL_DL_RX) _iwl3945_dbg_report_frame(priv, pkt, header, group100); } #else static inline void iwl3945_dbg_report_frame(struct iwl_priv *priv, struct iwl_rx_packet *pkt, struct ieee80211_hdr *header, int group100) { } #endif /* This is necessary only for a number of statistics, see the caller. */ static int iwl3945_is_network_packet(struct iwl_priv *priv, struct ieee80211_hdr *header) { /* Filter incoming packets to determine if they are targeted toward * this network, discarding packets coming from ourselves */ switch (priv->iw_mode) { case NL80211_IFTYPE_ADHOC: /* Header: Dest. | Source | BSSID */ /* packets to our IBSS update information */ return !compare_ether_addr(header->addr3, priv->bssid); case NL80211_IFTYPE_STATION: /* Header: Dest. | AP{BSSID} | Source */ /* packets to our IBSS update information */ return !compare_ether_addr(header->addr2, priv->bssid); default: return 1; } } static void iwl3945_pass_packet_to_mac80211(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb, struct ieee80211_rx_status *stats) { struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data; #ifdef CONFIG_IWLWIFI_LEDS struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)IWL_RX_DATA(pkt); #endif struct iwl3945_rx_frame_hdr *rx_hdr = IWL_RX_HDR(pkt); struct iwl3945_rx_frame_end *rx_end = IWL_RX_END(pkt); short len = le16_to_cpu(rx_hdr->len); /* We received data from the HW, so stop the watchdog */ if (unlikely((len + IWL39_RX_FRAME_SIZE) > skb_tailroom(rxb->skb))) { IWL_DEBUG_DROP(priv, "Corruption detected!\n"); return; } /* We only process data packets if the interface is open */ if (unlikely(!priv->is_open)) { IWL_DEBUG_DROP_LIMIT(priv, "Dropping packet while interface is not open.\n"); return; } skb_reserve(rxb->skb, (void *)rx_hdr->payload - (void *)pkt); /* Set the size of the skb to the size of the frame */ skb_put(rxb->skb, le16_to_cpu(rx_hdr->len)); if (!iwl3945_mod_params.sw_crypto) iwl_set_decrypted_flag(priv, (struct ieee80211_hdr *)rxb->skb->data, le32_to_cpu(rx_end->status), stats); #ifdef CONFIG_IWLWIFI_LEDS if (ieee80211_is_data(hdr->frame_control)) priv->rxtxpackets += len; #endif ieee80211_rx_irqsafe(priv->hw, rxb->skb, stats); rxb->skb = NULL; } #define IWL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6) static void iwl3945_rx_reply_rx(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb) { struct ieee80211_hdr *header; struct ieee80211_rx_status rx_status; struct iwl_rx_packet *pkt = (void *)rxb->skb->data; struct iwl3945_rx_frame_stats *rx_stats = IWL_RX_STATS(pkt); struct iwl3945_rx_frame_hdr *rx_hdr = IWL_RX_HDR(pkt); struct iwl3945_rx_frame_end *rx_end = IWL_RX_END(pkt); int snr; u16 rx_stats_sig_avg = le16_to_cpu(rx_stats->sig_avg); u16 rx_stats_noise_diff = le16_to_cpu(rx_stats->noise_diff); u8 network_packet; rx_status.flag = 0; rx_status.mactime = le64_to_cpu(rx_end->timestamp); rx_status.freq = ieee80211_channel_to_frequency(le16_to_cpu(rx_hdr->channel)); rx_status.band = (rx_hdr->phy_flags & RX_RES_PHY_FLAGS_BAND_24_MSK) ? IEEE80211_BAND_2GHZ : IEEE80211_BAND_5GHZ; rx_status.rate_idx = iwl3945_hwrate_to_plcp_idx(rx_hdr->rate); if (rx_status.band == IEEE80211_BAND_5GHZ) rx_status.rate_idx -= IWL_FIRST_OFDM_RATE; rx_status.antenna = le16_to_cpu(rx_hdr->phy_flags & RX_RES_PHY_FLAGS_ANTENNA_MSK) >> 4; /* set the preamble flag if appropriate */ if (rx_hdr->phy_flags & RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK) rx_status.flag |= RX_FLAG_SHORTPRE; if ((unlikely(rx_stats->phy_count > 20))) { IWL_DEBUG_DROP(priv, "dsp size out of range [0,20]: %d/n", rx_stats->phy_count); return; } if (!(rx_end->status & RX_RES_STATUS_NO_CRC32_ERROR) || !(rx_end->status & RX_RES_STATUS_NO_RXE_OVERFLOW)) { IWL_DEBUG_RX(priv, "Bad CRC or FIFO: 0x%08X.\n", rx_end->status); return; } /* Convert 3945's rssi indicator to dBm */ rx_status.signal = rx_stats->rssi - IWL39_RSSI_OFFSET; /* Set default noise value to -127 */ if (priv->last_rx_noise == 0) priv->last_rx_noise = IWL_NOISE_MEAS_NOT_AVAILABLE; /* 3945 provides noise info for OFDM frames only. * sig_avg and noise_diff are measured by the 3945's digital signal * processor (DSP), and indicate linear levels of signal level and * distortion/noise within the packet preamble after * automatic gain control (AGC). sig_avg should stay fairly * constant if the radio's AGC is working well. * Since these values are linear (not dB or dBm), linear * signal-to-noise ratio (SNR) is (sig_avg / noise_diff). * Convert linear SNR to dB SNR, then subtract that from rssi dBm * to obtain noise level in dBm. * Calculate rx_status.signal (quality indicator in %) based on SNR. */ if (rx_stats_noise_diff) { snr = rx_stats_sig_avg / rx_stats_noise_diff; rx_status.noise = rx_status.signal - iwl3945_calc_db_from_ratio(snr); rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, rx_status.noise); /* If noise info not available, calculate signal quality indicator (%) * using just the dBm signal level. */ } else { rx_status.noise = priv->last_rx_noise; rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, 0); } IWL_DEBUG_STATS(priv, "Rssi %d noise %d qual %d sig_avg %d noise_diff %d\n", rx_status.signal, rx_status.noise, rx_status.qual, rx_stats_sig_avg, rx_stats_noise_diff); header = (struct ieee80211_hdr *)IWL_RX_DATA(pkt); network_packet = iwl3945_is_network_packet(priv, header); IWL_DEBUG_STATS_LIMIT(priv, "[%c] %d RSSI:%d Signal:%u, Noise:%u, Rate:%u\n", network_packet ? '*' : ' ', le16_to_cpu(rx_hdr->channel), rx_status.signal, rx_status.signal, rx_status.noise, rx_status.rate_idx); /* Set "1" to report good data frames in groups of 100 */ iwl3945_dbg_report_frame(priv, pkt, header, 1); if (network_packet) { priv->last_beacon_time = le32_to_cpu(rx_end->beacon_timestamp); priv->last_tsf = le64_to_cpu(rx_end->timestamp); priv->last_rx_rssi = rx_status.signal; priv->last_rx_noise = rx_status.noise; } iwl3945_pass_packet_to_mac80211(priv, rxb, &rx_status); } int iwl3945_hw_txq_attach_buf_to_tfd(struct iwl_priv *priv, struct iwl_tx_queue *txq, dma_addr_t addr, u16 len, u8 reset, u8 pad) { int count; struct iwl_queue *q; struct iwl3945_tfd *tfd, *tfd_tmp; q = &txq->q; tfd_tmp = (struct iwl3945_tfd *)txq->tfds; tfd = &tfd_tmp[q->write_ptr]; if (reset) memset(tfd, 0, sizeof(*tfd)); count = TFD_CTL_COUNT_GET(le32_to_cpu(tfd->control_flags)); if ((count >= NUM_TFD_CHUNKS) || (count < 0)) { IWL_ERR(priv, "Error can not send more than %d chunks\n", NUM_TFD_CHUNKS); return -EINVAL; } tfd->tbs[count].addr = cpu_to_le32(addr); tfd->tbs[count].len = cpu_to_le32(len); count++; tfd->control_flags = cpu_to_le32(TFD_CTL_COUNT_SET(count) | TFD_CTL_PAD_SET(pad)); return 0; } /** * iwl3945_hw_txq_free_tfd - Free one TFD, those at index [txq->q.read_ptr] * * Does NOT advance any indexes */ void iwl3945_hw_txq_free_tfd(struct iwl_priv *priv, struct iwl_tx_queue *txq) { struct iwl3945_tfd *tfd_tmp = (struct iwl3945_tfd *)txq->tfds; int index = txq->q.read_ptr; struct iwl3945_tfd *tfd = &tfd_tmp[index]; struct pci_dev *dev = priv->pci_dev; int i; int counter; /* sanity check */ counter = TFD_CTL_COUNT_GET(le32_to_cpu(tfd->control_flags)); if (counter > NUM_TFD_CHUNKS) { IWL_ERR(priv, "Too many chunks: %i\n", counter); /* @todo issue fatal error, it is quite serious situation */ return; } /* Unmap tx_cmd */ if (counter) pci_unmap_single(dev, pci_unmap_addr(&txq->cmd[index]->meta, mapping), pci_unmap_len(&txq->cmd[index]->meta, len), PCI_DMA_TODEVICE); /* unmap chunks if any */ for (i = 1; i < counter; i++) { pci_unmap_single(dev, le32_to_cpu(tfd->tbs[i].addr), le32_to_cpu(tfd->tbs[i].len), PCI_DMA_TODEVICE); if (txq->txb[txq->q.read_ptr].skb[0]) { struct sk_buff *skb = txq->txb[txq->q.read_ptr].skb[0]; if (txq->txb[txq->q.read_ptr].skb[0]) { /* Can be called from interrupt context */ dev_kfree_skb_any(skb); txq->txb[txq->q.read_ptr].skb[0] = NULL; } } } return ; } /** * iwl3945_hw_build_tx_cmd_rate - Add rate portion to TX_CMD: * */ void iwl3945_hw_build_tx_cmd_rate(struct iwl_priv *priv, struct iwl_cmd *cmd, struct ieee80211_tx_info *info, struct ieee80211_hdr *hdr, int sta_id, int tx_id) { u16 hw_value = ieee80211_get_tx_rate(priv->hw, info)->hw_value; u16 rate_index = min(hw_value & 0xffff, IWL_RATE_COUNT - 1); u16 rate_mask; int rate; u8 rts_retry_limit; u8 data_retry_limit; __le32 tx_flags; __le16 fc = hdr->frame_control; struct iwl3945_tx_cmd *tx = (struct iwl3945_tx_cmd *)cmd->cmd.payload; rate = iwl3945_rates[rate_index].plcp; tx_flags = tx->tx_flags; /* We need to figure out how to get the sta->supp_rates while * in this running context */ rate_mask = IWL_RATES_MASK; if (tx_id >= IWL_CMD_QUEUE_NUM) rts_retry_limit = 3; else rts_retry_limit = 7; if (ieee80211_is_probe_resp(fc)) { data_retry_limit = 3; if (data_retry_limit < rts_retry_limit) rts_retry_limit = data_retry_limit; } else data_retry_limit = IWL_DEFAULT_TX_RETRY; if (priv->data_retry_limit != -1) data_retry_limit = priv->data_retry_limit; if (ieee80211_is_mgmt(fc)) { switch (fc & cpu_to_le16(IEEE80211_FCTL_STYPE)) { case cpu_to_le16(IEEE80211_STYPE_AUTH): case cpu_to_le16(IEEE80211_STYPE_DEAUTH): case cpu_to_le16(IEEE80211_STYPE_ASSOC_REQ): case cpu_to_le16(IEEE80211_STYPE_REASSOC_REQ): if (tx_flags & TX_CMD_FLG_RTS_MSK) { tx_flags &= ~TX_CMD_FLG_RTS_MSK; tx_flags |= TX_CMD_FLG_CTS_MSK; } break; default: break; } } tx->rts_retry_limit = rts_retry_limit; tx->data_retry_limit = data_retry_limit; tx->rate = rate; tx->tx_flags = tx_flags; /* OFDM */ tx->supp_rates[0] = ((rate_mask & IWL_OFDM_RATES_MASK) >> IWL_FIRST_OFDM_RATE) & 0xFF; /* CCK */ tx->supp_rates[1] = (rate_mask & 0xF); IWL_DEBUG_RATE(priv, "Tx sta id: %d, rate: %d (plcp), flags: 0x%4X " "cck/ofdm mask: 0x%x/0x%x\n", sta_id, tx->rate, le32_to_cpu(tx->tx_flags), tx->supp_rates[1], tx->supp_rates[0]); } u8 iwl3945_sync_sta(struct iwl_priv *priv, int sta_id, u16 tx_rate, u8 flags) { unsigned long flags_spin; struct iwl_station_entry *station; if (sta_id == IWL_INVALID_STATION) return IWL_INVALID_STATION; spin_lock_irqsave(&priv->sta_lock, flags_spin); station = &priv->stations[sta_id]; station->sta.sta.modify_mask = STA_MODIFY_TX_RATE_MSK; station->sta.rate_n_flags = cpu_to_le16(tx_rate); station->sta.mode = STA_CONTROL_MODIFY_MSK; spin_unlock_irqrestore(&priv->sta_lock, flags_spin); iwl_send_add_sta(priv, &station->sta, flags); IWL_DEBUG_RATE(priv, "SCALE sync station %d to rate %d\n", sta_id, tx_rate); return sta_id; } static int iwl3945_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src) { if (src == IWL_PWR_SRC_VAUX) { if (pci_pme_capable(priv->pci_dev, PCI_D3cold)) { iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG, APMG_PS_CTRL_VAL_PWR_SRC_VAUX, ~APMG_PS_CTRL_MSK_PWR_SRC); iwl_poll_bit(priv, CSR_GPIO_IN, CSR_GPIO_IN_VAL_VAUX_PWR_SRC, CSR_GPIO_IN_BIT_AUX_POWER, 5000); } } else { iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG, APMG_PS_CTRL_VAL_PWR_SRC_VMAIN, ~APMG_PS_CTRL_MSK_PWR_SRC); iwl_poll_bit(priv, CSR_GPIO_IN, CSR_GPIO_IN_VAL_VMAIN_PWR_SRC, CSR_GPIO_IN_BIT_AUX_POWER, 5000); /* uS */ } return 0; } static int iwl3945_rx_init(struct iwl_priv *priv, struct iwl_rx_queue *rxq) { iwl_write_direct32(priv, FH39_RCSR_RBD_BASE(0), rxq->dma_addr); iwl_write_direct32(priv, FH39_RCSR_RPTR_ADDR(0), rxq->rb_stts_dma); iwl_write_direct32(priv, FH39_RCSR_WPTR(0), 0); iwl_write_direct32(priv, FH39_RCSR_CONFIG(0), FH39_RCSR_RX_CONFIG_REG_VAL_DMA_CHNL_EN_ENABLE | FH39_RCSR_RX_CONFIG_REG_VAL_RDRBD_EN_ENABLE | FH39_RCSR_RX_CONFIG_REG_BIT_WR_STTS_EN | FH39_RCSR_RX_CONFIG_REG_VAL_MAX_FRAG_SIZE_128 | (RX_QUEUE_SIZE_LOG << FH39_RCSR_RX_CONFIG_REG_POS_RBDC_SIZE) | FH39_RCSR_RX_CONFIG_REG_VAL_IRQ_DEST_INT_HOST | (1 << FH39_RCSR_RX_CONFIG_REG_POS_IRQ_RBTH) | FH39_RCSR_RX_CONFIG_REG_VAL_MSG_MODE_FH); /* fake read to flush all prev I/O */ iwl_read_direct32(priv, FH39_RSSR_CTRL); return 0; } static int iwl3945_tx_reset(struct iwl_priv *priv) { /* bypass mode */ iwl_write_prph(priv, ALM_SCD_MODE_REG, 0x2); /* RA 0 is active */ iwl_write_prph(priv, ALM_SCD_ARASTAT_REG, 0x01); /* all 6 fifo are active */ iwl_write_prph(priv, ALM_SCD_TXFACT_REG, 0x3f); iwl_write_prph(priv, ALM_SCD_SBYP_MODE_1_REG, 0x010000); iwl_write_prph(priv, ALM_SCD_SBYP_MODE_2_REG, 0x030002); iwl_write_prph(priv, ALM_SCD_TXF4MF_REG, 0x000004); iwl_write_prph(priv, ALM_SCD_TXF5MF_REG, 0x000005); iwl_write_direct32(priv, FH39_TSSR_CBB_BASE, priv->shared_phys); iwl_write_direct32(priv, FH39_TSSR_MSG_CONFIG, FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TXPD_ON | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_TXPD_ON | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_128B | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TFD_ON | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_CBB_ON | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RSP_WAIT_TH | FH39_TSSR_TX_MSG_CONFIG_REG_VAL_RSP_WAIT_TH); return 0; } /** * iwl3945_txq_ctx_reset - Reset TX queue context * * Destroys all DMA structures and initialize them again */ static int iwl3945_txq_ctx_reset(struct iwl_priv *priv) { int rc; int txq_id, slots_num; iwl3945_hw_txq_ctx_free(priv); /* Tx CMD queue */ rc = iwl3945_tx_reset(priv); if (rc) goto error; /* Tx queue(s) */ for (txq_id = 0; txq_id <= priv->hw_params.max_txq_num; txq_id++) { slots_num = (txq_id == IWL_CMD_QUEUE_NUM) ? TFD_CMD_SLOTS : TFD_TX_CMD_SLOTS; rc = iwl_tx_queue_init(priv, &priv->txq[txq_id], slots_num, txq_id); if (rc) { IWL_ERR(priv, "Tx %d queue init failed\n", txq_id); goto error; } } return rc; error: iwl3945_hw_txq_ctx_free(priv); return rc; } static int iwl3945_apm_init(struct iwl_priv *priv) { int ret; iwl_power_initialize(priv); iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS, CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER); /* disable L0s without affecting L1 :don't wait for ICH L0s bug W/A) */ iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS, CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX); /* set "initialization complete" bit to move adapter * D0U* --> D0A* state */ iwl_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE); ret = iwl_poll_direct_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000); if (ret < 0) { IWL_DEBUG_INFO(priv, "Failed to init the card\n"); goto out; } /* enable DMA */ iwl_write_prph(priv, APMG_CLK_CTRL_REG, APMG_CLK_VAL_DMA_CLK_RQT | APMG_CLK_VAL_BSM_CLK_RQT); udelay(20); /* disable L1-Active */ iwl_set_bits_prph(priv, APMG_PCIDEV_STT_REG, APMG_PCIDEV_STT_VAL_L1_ACT_DIS); out: return ret; } static void iwl3945_nic_config(struct iwl_priv *priv) { struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; unsigned long flags; u8 rev_id = 0; spin_lock_irqsave(&priv->lock, flags); /* Determine HW type */ pci_read_config_byte(priv->pci_dev, PCI_REVISION_ID, &rev_id); IWL_DEBUG_INFO(priv, "HW Revision ID = 0x%X\n", rev_id); if (rev_id & PCI_CFG_REV_ID_BIT_RTP) IWL_DEBUG_INFO(priv, "RTP type \n"); else if (rev_id & PCI_CFG_REV_ID_BIT_BASIC_SKU) { IWL_DEBUG_INFO(priv, "3945 RADIO-MB type\n"); iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BIT_3945_MB); } else { IWL_DEBUG_INFO(priv, "3945 RADIO-MM type\n"); iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BIT_3945_MM); } if (EEPROM_SKU_CAP_OP_MODE_MRC == eeprom->sku_cap) { IWL_DEBUG_INFO(priv, "SKU OP mode is mrc\n"); iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC); } else IWL_DEBUG_INFO(priv, "SKU OP mode is basic\n"); if ((eeprom->board_revision & 0xF0) == 0xD0) { IWL_DEBUG_INFO(priv, "3945ABG revision is 0x%X\n", eeprom->board_revision); iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); } else { IWL_DEBUG_INFO(priv, "3945ABG revision is 0x%X\n", eeprom->board_revision); iwl_clear_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); } if (eeprom->almgor_m_version <= 1) { iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A); IWL_DEBUG_INFO(priv, "Card M type A version is 0x%X\n", eeprom->almgor_m_version); } else { IWL_DEBUG_INFO(priv, "Card M type B version is 0x%X\n", eeprom->almgor_m_version); iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG, CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B); } spin_unlock_irqrestore(&priv->lock, flags); if (eeprom->sku_cap & EEPROM_SKU_CAP_SW_RF_KILL_ENABLE) IWL_DEBUG_RF_KILL(priv, "SW RF KILL supported in EEPROM.\n"); if (eeprom->sku_cap & EEPROM_SKU_CAP_HW_RF_KILL_ENABLE) IWL_DEBUG_RF_KILL(priv, "HW RF KILL supported in EEPROM.\n"); } int iwl3945_hw_nic_init(struct iwl_priv *priv) { int rc; unsigned long flags; struct iwl_rx_queue *rxq = &priv->rxq; spin_lock_irqsave(&priv->lock, flags); priv->cfg->ops->lib->apm_ops.init(priv); spin_unlock_irqrestore(&priv->lock, flags); rc = priv->cfg->ops->lib->apm_ops.set_pwr_src(priv, IWL_PWR_SRC_VMAIN); if (rc) return rc; priv->cfg->ops->lib->apm_ops.config(priv); /* Allocate the RX queue, or reset if it is already allocated */ if (!rxq->bd) { rc = iwl_rx_queue_alloc(priv); if (rc) { IWL_ERR(priv, "Unable to initialize Rx queue\n"); return -ENOMEM; } } else iwl3945_rx_queue_reset(priv, rxq); iwl3945_rx_replenish(priv); iwl3945_rx_init(priv, rxq); /* Look at using this instead: rxq->need_update = 1; iwl_rx_queue_update_write_ptr(priv, rxq); */ iwl_write_direct32(priv, FH39_RCSR_WPTR(0), rxq->write & ~7); rc = iwl3945_txq_ctx_reset(priv); if (rc) return rc; set_bit(STATUS_INIT, &priv->status); return 0; } /** * iwl3945_hw_txq_ctx_free - Free TXQ Context * * Destroy all TX DMA queues and structures */ void iwl3945_hw_txq_ctx_free(struct iwl_priv *priv) { int txq_id; /* Tx queues */ for (txq_id = 0; txq_id <= priv->hw_params.max_txq_num; txq_id++) if (txq_id == IWL_CMD_QUEUE_NUM) iwl_cmd_queue_free(priv); else iwl_tx_queue_free(priv, txq_id); } void iwl3945_hw_txq_ctx_stop(struct iwl_priv *priv) { int txq_id; /* stop SCD */ iwl_write_prph(priv, ALM_SCD_MODE_REG, 0); /* reset TFD queues */ for (txq_id = 0; txq_id <= priv->hw_params.max_txq_num; txq_id++) { iwl_write_direct32(priv, FH39_TCSR_CONFIG(txq_id), 0x0); iwl_poll_direct_bit(priv, FH39_TSSR_TX_STATUS, FH39_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(txq_id), 1000); } iwl3945_hw_txq_ctx_free(priv); } static int iwl3945_apm_stop_master(struct iwl_priv *priv) { int ret = 0; unsigned long flags; spin_lock_irqsave(&priv->lock, flags); /* set stop master bit */ iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_STOP_MASTER); iwl_poll_direct_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_MASTER_DISABLED, 100); if (ret < 0) goto out; out: spin_unlock_irqrestore(&priv->lock, flags); IWL_DEBUG_INFO(priv, "stop master\n"); return ret; } static void iwl3945_apm_stop(struct iwl_priv *priv) { unsigned long flags; iwl3945_apm_stop_master(priv); spin_lock_irqsave(&priv->lock, flags); iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET); udelay(10); /* clear "init complete" move adapter D0A* --> D0U state */ iwl_clear_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE); spin_unlock_irqrestore(&priv->lock, flags); } static int iwl3945_apm_reset(struct iwl_priv *priv) { iwl3945_apm_stop_master(priv); iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET); udelay(10); iwl_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE); iwl_poll_direct_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000); iwl_write_prph(priv, APMG_CLK_CTRL_REG, APMG_CLK_VAL_BSM_CLK_RQT); iwl_write_prph(priv, APMG_RTC_INT_MSK_REG, 0x0); iwl_write_prph(priv, APMG_RTC_INT_STT_REG, 0xFFFFFFFF); /* enable DMA */ iwl_write_prph(priv, APMG_CLK_EN_REG, APMG_CLK_VAL_DMA_CLK_RQT | APMG_CLK_VAL_BSM_CLK_RQT); udelay(10); iwl_set_bits_prph(priv, APMG_PS_CTRL_REG, APMG_PS_CTRL_VAL_RESET_REQ); udelay(5); iwl_clear_bits_prph(priv, APMG_PS_CTRL_REG, APMG_PS_CTRL_VAL_RESET_REQ); /* Clear the 'host command active' bit... */ clear_bit(STATUS_HCMD_ACTIVE, &priv->status); wake_up_interruptible(&priv->wait_command_queue); return 0; } /** * iwl3945_hw_reg_adjust_power_by_temp * return index delta into power gain settings table */ static int iwl3945_hw_reg_adjust_power_by_temp(int new_reading, int old_reading) { return (new_reading - old_reading) * (-11) / 100; } /** * iwl3945_hw_reg_temp_out_of_range - Keep temperature in sane range */ static inline int iwl3945_hw_reg_temp_out_of_range(int temperature) { return ((temperature < -260) || (temperature > 25)) ? 1 : 0; } int iwl3945_hw_get_temperature(struct iwl_priv *priv) { return iwl_read32(priv, CSR_UCODE_DRV_GP2); } /** * iwl3945_hw_reg_txpower_get_temperature * get the current temperature by reading from NIC */ static int iwl3945_hw_reg_txpower_get_temperature(struct iwl_priv *priv) { struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; int temperature; temperature = iwl3945_hw_get_temperature(priv); /* driver's okay range is -260 to +25. * human readable okay range is 0 to +285 */ IWL_DEBUG_INFO(priv, "Temperature: %d\n", temperature + IWL_TEMP_CONVERT); /* handle insane temp reading */ if (iwl3945_hw_reg_temp_out_of_range(temperature)) { IWL_ERR(priv, "Error bad temperature value %d\n", temperature); /* if really really hot(?), * substitute the 3rd band/group's temp measured at factory */ if (priv->last_temperature > 100) temperature = eeprom->groups[2].temperature; else /* else use most recent "sane" value from driver */ temperature = priv->last_temperature; } return temperature; /* raw, not "human readable" */ } /* Adjust Txpower only if temperature variance is greater than threshold. * * Both are lower than older versions' 9 degrees */ #define IWL_TEMPERATURE_LIMIT_TIMER 6 /** * is_temp_calib_needed - determines if new calibration is needed * * records new temperature in tx_mgr->temperature. * replaces tx_mgr->last_temperature *only* if calib needed * (assumes caller will actually do the calibration!). */ static int is_temp_calib_needed(struct iwl_priv *priv) { int temp_diff; priv->temperature = iwl3945_hw_reg_txpower_get_temperature(priv); temp_diff = priv->temperature - priv->last_temperature; /* get absolute value */ if (temp_diff < 0) { IWL_DEBUG_POWER(priv, "Getting cooler, delta %d,\n", temp_diff); temp_diff = -temp_diff; } else if (temp_diff == 0) IWL_DEBUG_POWER(priv, "Same temp,\n"); else IWL_DEBUG_POWER(priv, "Getting warmer, delta %d,\n", temp_diff); /* if we don't need calibration, *don't* update last_temperature */ if (temp_diff < IWL_TEMPERATURE_LIMIT_TIMER) { IWL_DEBUG_POWER(priv, "Timed thermal calib not needed\n"); return 0; } IWL_DEBUG_POWER(priv, "Timed thermal calib needed\n"); /* assume that caller will actually do calib ... * update the "last temperature" value */ priv->last_temperature = priv->temperature; return 1; } #define IWL_MAX_GAIN_ENTRIES 78 #define IWL_CCK_FROM_OFDM_POWER_DIFF -5 #define IWL_CCK_FROM_OFDM_INDEX_DIFF (10) /* radio and DSP power table, each step is 1/2 dB. * 1st number is for RF analog gain, 2nd number is for DSP pre-DAC gain. */ static struct iwl3945_tx_power power_gain_table[2][IWL_MAX_GAIN_ENTRIES] = { { {251, 127}, /* 2.4 GHz, highest power */ {251, 127}, {251, 127}, {251, 127}, {251, 125}, {251, 110}, {251, 105}, {251, 98}, {187, 125}, {187, 115}, {187, 108}, {187, 99}, {243, 119}, {243, 111}, {243, 105}, {243, 97}, {243, 92}, {211, 106}, {211, 100}, {179, 120}, {179, 113}, {179, 107}, {147, 125}, {147, 119}, {147, 112}, {147, 106}, {147, 101}, {147, 97}, {147, 91}, {115, 107}, {235, 121}, {235, 115}, {235, 109}, {203, 127}, {203, 121}, {203, 115}, {203, 108}, {203, 102}, {203, 96}, {203, 92}, {171, 110}, {171, 104}, {171, 98}, {139, 116}, {227, 125}, {227, 119}, {227, 113}, {227, 107}, {227, 101}, {227, 96}, {195, 113}, {195, 106}, {195, 102}, {195, 95}, {163, 113}, {163, 106}, {163, 102}, {163, 95}, {131, 113}, {131, 106}, {131, 102}, {131, 95}, {99, 113}, {99, 106}, {99, 102}, {99, 95}, {67, 113}, {67, 106}, {67, 102}, {67, 95}, {35, 113}, {35, 106}, {35, 102}, {35, 95}, {3, 113}, {3, 106}, {3, 102}, {3, 95} }, /* 2.4 GHz, lowest power */ { {251, 127}, /* 5.x GHz, highest power */ {251, 120}, {251, 114}, {219, 119}, {219, 101}, {187, 113}, {187, 102}, {155, 114}, {155, 103}, {123, 117}, {123, 107}, {123, 99}, {123, 92}, {91, 108}, {59, 125}, {59, 118}, {59, 109}, {59, 102}, {59, 96}, {59, 90}, {27, 104}, {27, 98}, {27, 92}, {115, 118}, {115, 111}, {115, 104}, {83, 126}, {83, 121}, {83, 113}, {83, 105}, {83, 99}, {51, 118}, {51, 111}, {51, 104}, {51, 98}, {19, 116}, {19, 109}, {19, 102}, {19, 98}, {19, 93}, {171, 113}, {171, 107}, {171, 99}, {139, 120}, {139, 113}, {139, 107}, {139, 99}, {107, 120}, {107, 113}, {107, 107}, {107, 99}, {75, 120}, {75, 113}, {75, 107}, {75, 99}, {43, 120}, {43, 113}, {43, 107}, {43, 99}, {11, 120}, {11, 113}, {11, 107}, {11, 99}, {131, 107}, {131, 99}, {99, 120}, {99, 113}, {99, 107}, {99, 99}, {67, 120}, {67, 113}, {67, 107}, {67, 99}, {35, 120}, {35, 113}, {35, 107}, {35, 99}, {3, 120} } /* 5.x GHz, lowest power */ }; static inline u8 iwl3945_hw_reg_fix_power_index(int index) { if (index < 0) return 0; if (index >= IWL_MAX_GAIN_ENTRIES) return IWL_MAX_GAIN_ENTRIES - 1; return (u8) index; } /* Kick off thermal recalibration check every 60 seconds */ #define REG_RECALIB_PERIOD (60) /** * iwl3945_hw_reg_set_scan_power - Set Tx power for scan probe requests * * Set (in our channel info database) the direct scan Tx power for 1 Mbit (CCK) * or 6 Mbit (OFDM) rates. */ static void iwl3945_hw_reg_set_scan_power(struct iwl_priv *priv, u32 scan_tbl_index, s32 rate_index, const s8 *clip_pwrs, struct iwl_channel_info *ch_info, int band_index) { struct iwl3945_scan_power_info *scan_power_info; s8 power; u8 power_index; scan_power_info = &ch_info->scan_pwr_info[scan_tbl_index]; /* use this channel group's 6Mbit clipping/saturation pwr, * but cap at regulatory scan power restriction (set during init * based on eeprom channel data) for this channel. */ power = min(ch_info->scan_power, clip_pwrs[IWL_RATE_6M_INDEX_TABLE]); /* further limit to user's max power preference. * FIXME: Other spectrum management power limitations do not * seem to apply?? */ power = min(power, priv->tx_power_user_lmt); scan_power_info->requested_power = power; /* find difference between new scan *power* and current "normal" * Tx *power* for 6Mb. Use this difference (x2) to adjust the * current "normal" temperature-compensated Tx power *index* for * this rate (1Mb or 6Mb) to yield new temp-compensated scan power * *index*. */ power_index = ch_info->power_info[rate_index].power_table_index - (power - ch_info->power_info [IWL_RATE_6M_INDEX_TABLE].requested_power) * 2; /* store reference index that we use when adjusting *all* scan * powers. So we can accommodate user (all channel) or spectrum * management (single channel) power changes "between" temperature * feedback compensation procedures. * don't force fit this reference index into gain table; it may be a * negative number. This will help avoid errors when we're at * the lower bounds (highest gains, for warmest temperatures) * of the table. */ /* don't exceed table bounds for "real" setting */ power_index = iwl3945_hw_reg_fix_power_index(power_index); scan_power_info->power_table_index = power_index; scan_power_info->tpc.tx_gain = power_gain_table[band_index][power_index].tx_gain; scan_power_info->tpc.dsp_atten = power_gain_table[band_index][power_index].dsp_atten; } /** * iwl3945_send_tx_power - fill in Tx Power command with gain settings * * Configures power settings for all rates for the current channel, * using values from channel info struct, and send to NIC */ static int iwl3945_send_tx_power(struct iwl_priv *priv) { int rate_idx, i; const struct iwl_channel_info *ch_info = NULL; struct iwl3945_txpowertable_cmd txpower = { .channel = priv->active_rxon.channel, }; txpower.band = (priv->band == IEEE80211_BAND_5GHZ) ? 0 : 1; ch_info = iwl_get_channel_info(priv, priv->band, le16_to_cpu(priv->active_rxon.channel)); if (!ch_info) { IWL_ERR(priv, "Failed to get channel info for channel %d [%d]\n", le16_to_cpu(priv->active_rxon.channel), priv->band); return -EINVAL; } if (!is_channel_valid(ch_info)) { IWL_DEBUG_POWER(priv, "Not calling TX_PWR_TABLE_CMD on " "non-Tx channel.\n"); return 0; } /* fill cmd with power settings for all rates for current channel */ /* Fill OFDM rate */ for (rate_idx = IWL_FIRST_OFDM_RATE, i = 0; rate_idx <= IWL39_LAST_OFDM_RATE; rate_idx++, i++) { txpower.power[i].tpc = ch_info->power_info[i].tpc; txpower.power[i].rate = iwl3945_rates[rate_idx].plcp; IWL_DEBUG_POWER(priv, "ch %d:%d rf %d dsp %3d rate code 0x%02x\n", le16_to_cpu(txpower.channel), txpower.band, txpower.power[i].tpc.tx_gain, txpower.power[i].tpc.dsp_atten, txpower.power[i].rate); } /* Fill CCK rates */ for (rate_idx = IWL_FIRST_CCK_RATE; rate_idx <= IWL_LAST_CCK_RATE; rate_idx++, i++) { txpower.power[i].tpc = ch_info->power_info[i].tpc; txpower.power[i].rate = iwl3945_rates[rate_idx].plcp; IWL_DEBUG_POWER(priv, "ch %d:%d rf %d dsp %3d rate code 0x%02x\n", le16_to_cpu(txpower.channel), txpower.band, txpower.power[i].tpc.tx_gain, txpower.power[i].tpc.dsp_atten, txpower.power[i].rate); } return iwl_send_cmd_pdu(priv, REPLY_TX_PWR_TABLE_CMD, sizeof(struct iwl3945_txpowertable_cmd), &txpower); } /** * iwl3945_hw_reg_set_new_power - Configures power tables at new levels * @ch_info: Channel to update. Uses power_info.requested_power. * * Replace requested_power and base_power_index ch_info fields for * one channel. * * Called if user or spectrum management changes power preferences. * Takes into account h/w and modulation limitations (clip power). * * This does *not* send anything to NIC, just sets up ch_info for one channel. * * NOTE: reg_compensate_for_temperature_dif() *must* be run after this to * properly fill out the scan powers, and actual h/w gain settings, * and send changes to NIC */ static int iwl3945_hw_reg_set_new_power(struct iwl_priv *priv, struct iwl_channel_info *ch_info) { struct iwl3945_channel_power_info *power_info; int power_changed = 0; int i; const s8 *clip_pwrs; int power; /* Get this chnlgrp's rate-to-max/clip-powers table */ clip_pwrs = priv->clip39_groups[ch_info->group_index].clip_powers; /* Get this channel's rate-to-current-power settings table */ power_info = ch_info->power_info; /* update OFDM Txpower settings */ for (i = IWL_RATE_6M_INDEX_TABLE; i <= IWL_RATE_54M_INDEX_TABLE; i++, ++power_info) { int delta_idx; /* limit new power to be no more than h/w capability */ power = min(ch_info->curr_txpow, clip_pwrs[i]); if (power == power_info->requested_power) continue; /* find difference between old and new requested powers, * update base (non-temp-compensated) power index */ delta_idx = (power - power_info->requested_power) * 2; power_info->base_power_index -= delta_idx; /* save new requested power value */ power_info->requested_power = power; power_changed = 1; } /* update CCK Txpower settings, based on OFDM 12M setting ... * ... all CCK power settings for a given channel are the *same*. */ if (power_changed) { power = ch_info->power_info[IWL_RATE_12M_INDEX_TABLE]. requested_power + IWL_CCK_FROM_OFDM_POWER_DIFF; /* do all CCK rates' iwl3945_channel_power_info structures */ for (i = IWL_RATE_1M_INDEX_TABLE; i <= IWL_RATE_11M_INDEX_TABLE; i++) { power_info->requested_power = power; power_info->base_power_index = ch_info->power_info[IWL_RATE_12M_INDEX_TABLE]. base_power_index + IWL_CCK_FROM_OFDM_INDEX_DIFF; ++power_info; } } return 0; } /** * iwl3945_hw_reg_get_ch_txpower_limit - returns new power limit for channel * * NOTE: Returned power limit may be less (but not more) than requested, * based strictly on regulatory (eeprom and spectrum mgt) limitations * (no consideration for h/w clipping limitations). */ static int iwl3945_hw_reg_get_ch_txpower_limit(struct iwl_channel_info *ch_info) { s8 max_power; #if 0 /* if we're using TGd limits, use lower of TGd or EEPROM */ if (ch_info->tgd_data.max_power != 0) max_power = min(ch_info->tgd_data.max_power, ch_info->eeprom.max_power_avg); /* else just use EEPROM limits */ else #endif max_power = ch_info->eeprom.max_power_avg; return min(max_power, ch_info->max_power_avg); } /** * iwl3945_hw_reg_comp_txpower_temp - Compensate for temperature * * Compensate txpower settings of *all* channels for temperature. * This only accounts for the difference between current temperature * and the factory calibration temperatures, and bases the new settings * on the channel's base_power_index. * * If RxOn is "associated", this sends the new Txpower to NIC! */ static int iwl3945_hw_reg_comp_txpower_temp(struct iwl_priv *priv) { struct iwl_channel_info *ch_info = NULL; struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; int delta_index; const s8 *clip_pwrs; /* array of h/w max power levels for each rate */ u8 a_band; u8 rate_index; u8 scan_tbl_index; u8 i; int ref_temp; int temperature = priv->temperature; /* set up new Tx power info for each and every channel, 2.4 and 5.x */ for (i = 0; i < priv->channel_count; i++) { ch_info = &priv->channel_info[i]; a_band = is_channel_a_band(ch_info); /* Get this chnlgrp's factory calibration temperature */ ref_temp = (s16)eeprom->groups[ch_info->group_index]. temperature; /* get power index adjustment based on current and factory * temps */ delta_index = iwl3945_hw_reg_adjust_power_by_temp(temperature, ref_temp); /* set tx power value for all rates, OFDM and CCK */ for (rate_index = 0; rate_index < IWL_RATE_COUNT; rate_index++) { int power_idx = ch_info->power_info[rate_index].base_power_index; /* temperature compensate */ power_idx += delta_index; /* stay within table range */ power_idx = iwl3945_hw_reg_fix_power_index(power_idx); ch_info->power_info[rate_index]. power_table_index = (u8) power_idx; ch_info->power_info[rate_index].tpc = power_gain_table[a_band][power_idx]; } /* Get this chnlgrp's rate-to-max/clip-powers table */ clip_pwrs = priv->clip39_groups[ch_info->group_index].clip_powers; /* set scan tx power, 1Mbit for CCK, 6Mbit for OFDM */ for (scan_tbl_index = 0; scan_tbl_index < IWL_NUM_SCAN_RATES; scan_tbl_index++) { s32 actual_index = (scan_tbl_index == 0) ? IWL_RATE_1M_INDEX_TABLE : IWL_RATE_6M_INDEX_TABLE; iwl3945_hw_reg_set_scan_power(priv, scan_tbl_index, actual_index, clip_pwrs, ch_info, a_band); } } /* send Txpower command for current channel to ucode */ return priv->cfg->ops->lib->send_tx_power(priv); } int iwl3945_hw_reg_set_txpower(struct iwl_priv *priv, s8 power) { struct iwl_channel_info *ch_info; s8 max_power; u8 a_band; u8 i; if (priv->tx_power_user_lmt == power) { IWL_DEBUG_POWER(priv, "Requested Tx power same as current " "limit: %ddBm.\n", power); return 0; } IWL_DEBUG_POWER(priv, "Setting upper limit clamp to %ddBm.\n", power); priv->tx_power_user_lmt = power; /* set up new Tx powers for each and every channel, 2.4 and 5.x */ for (i = 0; i < priv->channel_count; i++) { ch_info = &priv->channel_info[i]; a_band = is_channel_a_band(ch_info); /* find minimum power of all user and regulatory constraints * (does not consider h/w clipping limitations) */ max_power = iwl3945_hw_reg_get_ch_txpower_limit(ch_info); max_power = min(power, max_power); if (max_power != ch_info->curr_txpow) { ch_info->curr_txpow = max_power; /* this considers the h/w clipping limitations */ iwl3945_hw_reg_set_new_power(priv, ch_info); } } /* update txpower settings for all channels, * send to NIC if associated. */ is_temp_calib_needed(priv); iwl3945_hw_reg_comp_txpower_temp(priv); return 0; } static int iwl3945_send_rxon_assoc(struct iwl_priv *priv) { int rc = 0; struct iwl_rx_packet *res = NULL; struct iwl3945_rxon_assoc_cmd rxon_assoc; struct iwl_host_cmd cmd = { .id = REPLY_RXON_ASSOC, .len = sizeof(rxon_assoc), .meta.flags = CMD_WANT_SKB, .data = &rxon_assoc, }; const struct iwl_rxon_cmd *rxon1 = &priv->staging_rxon; const struct iwl_rxon_cmd *rxon2 = &priv->active_rxon; if ((rxon1->flags == rxon2->flags) && (rxon1->filter_flags == rxon2->filter_flags) && (rxon1->cck_basic_rates == rxon2->cck_basic_rates) && (rxon1->ofdm_basic_rates == rxon2->ofdm_basic_rates)) { IWL_DEBUG_INFO(priv, "Using current RXON_ASSOC. Not resending.\n"); return 0; } rxon_assoc.flags = priv->staging_rxon.flags; rxon_assoc.filter_flags = priv->staging_rxon.filter_flags; rxon_assoc.ofdm_basic_rates = priv->staging_rxon.ofdm_basic_rates; rxon_assoc.cck_basic_rates = priv->staging_rxon.cck_basic_rates; rxon_assoc.reserved = 0; rc = iwl_send_cmd_sync(priv, &cmd); if (rc) return rc; res = (struct iwl_rx_packet *)cmd.meta.u.skb->data; if (res->hdr.flags & IWL_CMD_FAILED_MSK) { IWL_ERR(priv, "Bad return from REPLY_RXON_ASSOC command\n"); rc = -EIO; } priv->alloc_rxb_skb--; dev_kfree_skb_any(cmd.meta.u.skb); return rc; } /** * iwl3945_commit_rxon - commit staging_rxon to hardware * * The RXON command in staging_rxon is committed to the hardware and * the active_rxon structure is updated with the new data. This * function correctly transitions out of the RXON_ASSOC_MSK state if * a HW tune is required based on the RXON structure changes. */ static int iwl3945_commit_rxon(struct iwl_priv *priv) { /* cast away the const for active_rxon in this function */ struct iwl3945_rxon_cmd *active_rxon = (void *)&priv->active_rxon; struct iwl3945_rxon_cmd *staging_rxon = (void *)&priv->staging_rxon; int rc = 0; bool new_assoc = !!(priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK); if (!iwl_is_alive(priv)) return -1; /* always get timestamp with Rx frame */ staging_rxon->flags |= RXON_FLG_TSF2HOST_MSK; /* select antenna */ staging_rxon->flags &= ~(RXON_FLG_DIS_DIV_MSK | RXON_FLG_ANT_SEL_MSK); staging_rxon->flags |= iwl3945_get_antenna_flags(priv); rc = iwl_check_rxon_cmd(priv); if (rc) { IWL_ERR(priv, "Invalid RXON configuration. Not committing.\n"); return -EINVAL; } /* If we don't need to send a full RXON, we can use * iwl3945_rxon_assoc_cmd which is used to reconfigure filter * and other flags for the current radio configuration. */ if (!iwl_full_rxon_required(priv)) { rc = iwl_send_rxon_assoc(priv); if (rc) { IWL_ERR(priv, "Error setting RXON_ASSOC " "configuration (%d).\n", rc); return rc; } memcpy(active_rxon, staging_rxon, sizeof(*active_rxon)); return 0; } /* If we are currently associated and the new config requires * an RXON_ASSOC and the new config wants the associated mask enabled, * we must clear the associated from the active configuration * before we apply the new config */ if (iwl_is_associated(priv) && new_assoc) { IWL_DEBUG_INFO(priv, "Toggling associated bit on current RXON\n"); active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK; /* * reserved4 and 5 could have been filled by the iwlcore code. * Let's clear them before pushing to the 3945. */ active_rxon->reserved4 = 0; active_rxon->reserved5 = 0; rc = iwl_send_cmd_pdu(priv, REPLY_RXON, sizeof(struct iwl3945_rxon_cmd), &priv->active_rxon); /* If the mask clearing failed then we set * active_rxon back to what it was previously */ if (rc) { active_rxon->filter_flags |= RXON_FILTER_ASSOC_MSK; IWL_ERR(priv, "Error clearing ASSOC_MSK on current " "configuration (%d).\n", rc); return rc; } } IWL_DEBUG_INFO(priv, "Sending RXON\n" "* with%s RXON_FILTER_ASSOC_MSK\n" "* channel = %d\n" "* bssid = %pM\n", (new_assoc ? "" : "out"), le16_to_cpu(staging_rxon->channel), staging_rxon->bssid_addr); /* * reserved4 and 5 could have been filled by the iwlcore code. * Let's clear them before pushing to the 3945. */ staging_rxon->reserved4 = 0; staging_rxon->reserved5 = 0; iwl_set_rxon_hwcrypto(priv, !priv->hw_params.sw_crypto); /* Apply the new configuration */ rc = iwl_send_cmd_pdu(priv, REPLY_RXON, sizeof(struct iwl3945_rxon_cmd), staging_rxon); if (rc) { IWL_ERR(priv, "Error setting new configuration (%d).\n", rc); return rc; } memcpy(active_rxon, staging_rxon, sizeof(*active_rxon)); iwl_clear_stations_table(priv); /* If we issue a new RXON command which required a tune then we must * send a new TXPOWER command or we won't be able to Tx any frames */ rc = priv->cfg->ops->lib->send_tx_power(priv); if (rc) { IWL_ERR(priv, "Error setting Tx power (%d).\n", rc); return rc; } /* Add the broadcast address so we can send broadcast frames */ if (iwl_add_station(priv, iwl_bcast_addr, false, CMD_SYNC, NULL) == IWL_INVALID_STATION) { IWL_ERR(priv, "Error adding BROADCAST address for transmit.\n"); return -EIO; } /* If we have set the ASSOC_MSK and we are in BSS mode then * add the IWL_AP_ID to the station rate table */ if (iwl_is_associated(priv) && (priv->iw_mode == NL80211_IFTYPE_STATION)) if (iwl_add_station(priv, priv->active_rxon.bssid_addr, true, CMD_SYNC, NULL) == IWL_INVALID_STATION) { IWL_ERR(priv, "Error adding AP address for transmit\n"); return -EIO; } /* Init the hardware's rate fallback order based on the band */ rc = iwl3945_init_hw_rate_table(priv); if (rc) { IWL_ERR(priv, "Error setting HW rate table: %02X\n", rc); return -EIO; } return 0; } /* will add 3945 channel switch cmd handling later */ int iwl3945_hw_channel_switch(struct iwl_priv *priv, u16 channel) { return 0; } /** * iwl3945_reg_txpower_periodic - called when time to check our temperature. * * -- reset periodic timer * -- see if temp has changed enough to warrant re-calibration ... if so: * -- correct coeffs for temp (can reset temp timer) * -- save this temp as "last", * -- send new set of gain settings to NIC * NOTE: This should continue working, even when we're not associated, * so we can keep our internal table of scan powers current. */ void iwl3945_reg_txpower_periodic(struct iwl_priv *priv) { /* This will kick in the "brute force" * iwl3945_hw_reg_comp_txpower_temp() below */ if (!is_temp_calib_needed(priv)) goto reschedule; /* Set up a new set of temp-adjusted TxPowers, send to NIC. * This is based *only* on current temperature, * ignoring any previous power measurements */ iwl3945_hw_reg_comp_txpower_temp(priv); reschedule: queue_delayed_work(priv->workqueue, &priv->thermal_periodic, REG_RECALIB_PERIOD * HZ); } static void iwl3945_bg_reg_txpower_periodic(struct work_struct *work) { struct iwl_priv *priv = container_of(work, struct iwl_priv, thermal_periodic.work); if (test_bit(STATUS_EXIT_PENDING, &priv->status)) return; mutex_lock(&priv->mutex); iwl3945_reg_txpower_periodic(priv); mutex_unlock(&priv->mutex); } /** * iwl3945_hw_reg_get_ch_grp_index - find the channel-group index (0-4) * for the channel. * * This function is used when initializing channel-info structs. * * NOTE: These channel groups do *NOT* match the bands above! * These channel groups are based on factory-tested channels; * on A-band, EEPROM's "group frequency" entries represent the top * channel in each group 1-4. Group 5 All B/G channels are in group 0. */ static u16 iwl3945_hw_reg_get_ch_grp_index(struct iwl_priv *priv, const struct iwl_channel_info *ch_info) { struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; struct iwl3945_eeprom_txpower_group *ch_grp = &eeprom->groups[0]; u8 group; u16 group_index = 0; /* based on factory calib frequencies */ u8 grp_channel; /* Find the group index for the channel ... don't use index 1(?) */ if (is_channel_a_band(ch_info)) { for (group = 1; group < 5; group++) { grp_channel = ch_grp[group].group_channel; if (ch_info->channel <= grp_channel) { group_index = group; break; } } /* group 4 has a few channels *above* its factory cal freq */ if (group == 5) group_index = 4; } else group_index = 0; /* 2.4 GHz, group 0 */ IWL_DEBUG_POWER(priv, "Chnl %d mapped to grp %d\n", ch_info->channel, group_index); return group_index; } /** * iwl3945_hw_reg_get_matched_power_index - Interpolate to get nominal index * * Interpolate to get nominal (i.e. at factory calibration temperature) index * into radio/DSP gain settings table for requested power. */ static int iwl3945_hw_reg_get_matched_power_index(struct iwl_priv *priv, s8 requested_power, s32 setting_index, s32 *new_index) { const struct iwl3945_eeprom_txpower_group *chnl_grp = NULL; struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; s32 index0, index1; s32 power = 2 * requested_power; s32 i; const struct iwl3945_eeprom_txpower_sample *samples; s32 gains0, gains1; s32 res; s32 denominator; chnl_grp = &eeprom->groups[setting_index]; samples = chnl_grp->samples; for (i = 0; i < 5; i++) { if (power == samples[i].power) { *new_index = samples[i].gain_index; return 0; } } if (power > samples[1].power) { index0 = 0; index1 = 1; } else if (power > samples[2].power) { index0 = 1; index1 = 2; } else if (power > samples[3].power) { index0 = 2; index1 = 3; } else { index0 = 3; index1 = 4; } denominator = (s32) samples[index1].power - (s32) samples[index0].power; if (denominator == 0) return -EINVAL; gains0 = (s32) samples[index0].gain_index * (1 << 19); gains1 = (s32) samples[index1].gain_index * (1 << 19); res = gains0 + (gains1 - gains0) * ((s32) power - (s32) samples[index0].power) / denominator + (1 << 18); *new_index = res >> 19; return 0; } static void iwl3945_hw_reg_init_channel_groups(struct iwl_priv *priv) { u32 i; s32 rate_index; struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; const struct iwl3945_eeprom_txpower_group *group; IWL_DEBUG_POWER(priv, "Initializing factory calib info from EEPROM\n"); for (i = 0; i < IWL_NUM_TX_CALIB_GROUPS; i++) { s8 *clip_pwrs; /* table of power levels for each rate */ s8 satur_pwr; /* saturation power for each chnl group */ group = &eeprom->groups[i]; /* sanity check on factory saturation power value */ if (group->saturation_power < 40) { IWL_WARN(priv, "Error: saturation power is %d, " "less than minimum expected 40\n", group->saturation_power); return; } /* * Derive requested power levels for each rate, based on * hardware capabilities (saturation power for band). * Basic value is 3dB down from saturation, with further * power reductions for highest 3 data rates. These * backoffs provide headroom for high rate modulation * power peaks, without too much distortion (clipping). */ /* we'll fill in this array with h/w max power levels */ clip_pwrs = (s8 *) priv->clip39_groups[i].clip_powers; /* divide factory saturation power by 2 to find -3dB level */ satur_pwr = (s8) (group->saturation_power >> 1); /* fill in channel group's nominal powers for each rate */ for (rate_index = 0; rate_index < IWL_RATE_COUNT; rate_index++, clip_pwrs++) { switch (rate_index) { case IWL_RATE_36M_INDEX_TABLE: if (i == 0) /* B/G */ *clip_pwrs = satur_pwr; else /* A */ *clip_pwrs = satur_pwr - 5; break; case IWL_RATE_48M_INDEX_TABLE: if (i == 0) *clip_pwrs = satur_pwr - 7; else *clip_pwrs = satur_pwr - 10; break; case IWL_RATE_54M_INDEX_TABLE: if (i == 0) *clip_pwrs = satur_pwr - 9; else *clip_pwrs = satur_pwr - 12; break; default: *clip_pwrs = satur_pwr; break; } } } } /** * iwl3945_txpower_set_from_eeprom - Set channel power info based on EEPROM * * Second pass (during init) to set up priv->channel_info * * Set up Tx-power settings in our channel info database for each VALID * (for this geo/SKU) channel, at all Tx data rates, based on eeprom values * and current temperature. * * Since this is based on current temperature (at init time), these values may * not be valid for very long, but it gives us a starting/default point, * and allows us to active (i.e. using Tx) scan. * * This does *not* write values to NIC, just sets up our internal table. */ int iwl3945_txpower_set_from_eeprom(struct iwl_priv *priv) { struct iwl_channel_info *ch_info = NULL; struct iwl3945_channel_power_info *pwr_info; struct iwl3945_eeprom *eeprom = (struct iwl3945_eeprom *)priv->eeprom; int delta_index; u8 rate_index; u8 scan_tbl_index; const s8 *clip_pwrs; /* array of power levels for each rate */ u8 gain, dsp_atten; s8 power; u8 pwr_index, base_pwr_index, a_band; u8 i; int temperature; /* save temperature reference, * so we can determine next time to calibrate */ temperature = iwl3945_hw_reg_txpower_get_temperature(priv); priv->last_temperature = temperature; iwl3945_hw_reg_init_channel_groups(priv); /* initialize Tx power info for each and every channel, 2.4 and 5.x */ for (i = 0, ch_info = priv->channel_info; i < priv->channel_count; i++, ch_info++) { a_band = is_channel_a_band(ch_info); if (!is_channel_valid(ch_info)) continue; /* find this channel's channel group (*not* "band") index */ ch_info->group_index = iwl3945_hw_reg_get_ch_grp_index(priv, ch_info); /* Get this chnlgrp's rate->max/clip-powers table */ clip_pwrs = priv->clip39_groups[ch_info->group_index].clip_powers; /* calculate power index *adjustment* value according to * diff between current temperature and factory temperature */ delta_index = iwl3945_hw_reg_adjust_power_by_temp(temperature, eeprom->groups[ch_info->group_index]. temperature); IWL_DEBUG_POWER(priv, "Delta index for channel %d: %d [%d]\n", ch_info->channel, delta_index, temperature + IWL_TEMP_CONVERT); /* set tx power value for all OFDM rates */ for (rate_index = 0; rate_index < IWL_OFDM_RATES; rate_index++) { s32 uninitialized_var(power_idx); int rc; /* use channel group's clip-power table, * but don't exceed channel's max power */ s8 pwr = min(ch_info->max_power_avg, clip_pwrs[rate_index]); pwr_info = &ch_info->power_info[rate_index]; /* get base (i.e. at factory-measured temperature) * power table index for this rate's power */ rc = iwl3945_hw_reg_get_matched_power_index(priv, pwr, ch_info->group_index, &power_idx); if (rc) { IWL_ERR(priv, "Invalid power index\n"); return rc; } pwr_info->base_power_index = (u8) power_idx; /* temperature compensate */ power_idx += delta_index; /* stay within range of gain table */ power_idx = iwl3945_hw_reg_fix_power_index(power_idx); /* fill 1 OFDM rate's iwl3945_channel_power_info struct */ pwr_info->requested_power = pwr; pwr_info->power_table_index = (u8) power_idx; pwr_info->tpc.tx_gain = power_gain_table[a_band][power_idx].tx_gain; pwr_info->tpc.dsp_atten = power_gain_table[a_band][power_idx].dsp_atten; } /* set tx power for CCK rates, based on OFDM 12 Mbit settings*/ pwr_info = &ch_info->power_info[IWL_RATE_12M_INDEX_TABLE]; power = pwr_info->requested_power + IWL_CCK_FROM_OFDM_POWER_DIFF; pwr_index = pwr_info->power_table_index + IWL_CCK_FROM_OFDM_INDEX_DIFF; base_pwr_index = pwr_info->base_power_index + IWL_CCK_FROM_OFDM_INDEX_DIFF; /* stay within table range */ pwr_index = iwl3945_hw_reg_fix_power_index(pwr_index); gain = power_gain_table[a_band][pwr_index].tx_gain; dsp_atten = power_gain_table[a_band][pwr_index].dsp_atten; /* fill each CCK rate's iwl3945_channel_power_info structure * NOTE: All CCK-rate Txpwrs are the same for a given chnl! * NOTE: CCK rates start at end of OFDM rates! */ for (rate_index = 0; rate_index < IWL_CCK_RATES; rate_index++) { pwr_info = &ch_info->power_info[rate_index+IWL_OFDM_RATES]; pwr_info->requested_power = power; pwr_info->power_table_index = pwr_index; pwr_info->base_power_index = base_pwr_index; pwr_info->tpc.tx_gain = gain; pwr_info->tpc.dsp_atten = dsp_atten; } /* set scan tx power, 1Mbit for CCK, 6Mbit for OFDM */ for (scan_tbl_index = 0; scan_tbl_index < IWL_NUM_SCAN_RATES; scan_tbl_index++) { s32 actual_index = (scan_tbl_index == 0) ? IWL_RATE_1M_INDEX_TABLE : IWL_RATE_6M_INDEX_TABLE; iwl3945_hw_reg_set_scan_power(priv, scan_tbl_index, actual_index, clip_pwrs, ch_info, a_band); } } return 0; } int iwl3945_hw_rxq_stop(struct iwl_priv *priv) { int rc; iwl_write_direct32(priv, FH39_RCSR_CONFIG(0), 0); rc = iwl_poll_direct_bit(priv, FH39_RSSR_STATUS, FH39_RSSR_CHNL0_RX_STATUS_CHNL_IDLE, 1000); if (rc < 0) IWL_ERR(priv, "Can't stop Rx DMA.\n"); return 0; } int iwl3945_hw_tx_queue_init(struct iwl_priv *priv, struct iwl_tx_queue *txq) { int txq_id = txq->q.id; struct iwl3945_shared *shared_data = priv->shared_virt; shared_data->tx_base_ptr[txq_id] = cpu_to_le32((u32)txq->q.dma_addr); iwl_write_direct32(priv, FH39_CBCC_CTRL(txq_id), 0); iwl_write_direct32(priv, FH39_CBCC_BASE(txq_id), 0); iwl_write_direct32(priv, FH39_TCSR_CONFIG(txq_id), FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT | FH39_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF | FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD | FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL | FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE); /* fake read to flush all prev. writes */ iwl_read32(priv, FH39_TSSR_CBB_BASE); return 0; } /* * HCMD utils */ static u16 iwl3945_get_hcmd_size(u8 cmd_id, u16 len) { switch (cmd_id) { case REPLY_RXON: return sizeof(struct iwl3945_rxon_cmd); case POWER_TABLE_CMD: return sizeof(struct iwl3945_powertable_cmd); default: return len; } } static u16 iwl3945_build_addsta_hcmd(const struct iwl_addsta_cmd *cmd, u8 *data) { struct iwl3945_addsta_cmd *addsta = (struct iwl3945_addsta_cmd *)data; addsta->mode = cmd->mode; memcpy(&addsta->sta, &cmd->sta, sizeof(struct sta_id_modify)); memcpy(&addsta->key, &cmd->key, sizeof(struct iwl4965_keyinfo)); addsta->station_flags = cmd->station_flags; addsta->station_flags_msk = cmd->station_flags_msk; addsta->tid_disable_tx = cpu_to_le16(0); addsta->rate_n_flags = cmd->rate_n_flags; addsta->add_immediate_ba_tid = cmd->add_immediate_ba_tid; addsta->remove_immediate_ba_tid = cmd->remove_immediate_ba_tid; addsta->add_immediate_ba_ssn = cmd->add_immediate_ba_ssn; return (u16)sizeof(struct iwl3945_addsta_cmd); } /** * iwl3945_init_hw_rate_table - Initialize the hardware rate fallback table */ int iwl3945_init_hw_rate_table(struct iwl_priv *priv) { int rc, i, index, prev_index; struct iwl3945_rate_scaling_cmd rate_cmd = { .reserved = {0, 0, 0}, }; struct iwl3945_rate_scaling_info *table = rate_cmd.table; for (i = 0; i < ARRAY_SIZE(iwl3945_rates); i++) { index = iwl3945_rates[i].table_rs_index; table[index].rate_n_flags = iwl3945_hw_set_rate_n_flags(iwl3945_rates[i].plcp, 0); table[index].try_cnt = priv->retry_rate; prev_index = iwl3945_get_prev_ieee_rate(i); table[index].next_rate_index = iwl3945_rates[prev_index].table_rs_index; } switch (priv->band) { case IEEE80211_BAND_5GHZ: IWL_DEBUG_RATE(priv, "Select A mode rate scale\n"); /* If one of the following CCK rates is used, * have it fall back to the 6M OFDM rate */ for (i = IWL_RATE_1M_INDEX_TABLE; i <= IWL_RATE_11M_INDEX_TABLE; i++) table[i].next_rate_index = iwl3945_rates[IWL_FIRST_OFDM_RATE].table_rs_index; /* Don't fall back to CCK rates */ table[IWL_RATE_12M_INDEX_TABLE].next_rate_index = IWL_RATE_9M_INDEX_TABLE; /* Don't drop out of OFDM rates */ table[IWL_RATE_6M_INDEX_TABLE].next_rate_index = iwl3945_rates[IWL_FIRST_OFDM_RATE].table_rs_index; break; case IEEE80211_BAND_2GHZ: IWL_DEBUG_RATE(priv, "Select B/G mode rate scale\n"); /* If an OFDM rate is used, have it fall back to the * 1M CCK rates */ if (!(priv->sta_supp_rates & IWL_OFDM_RATES_MASK) && iwl_is_associated(priv)) { index = IWL_FIRST_CCK_RATE; for (i = IWL_RATE_6M_INDEX_TABLE; i <= IWL_RATE_54M_INDEX_TABLE; i++) table[i].next_rate_index = iwl3945_rates[index].table_rs_index; index = IWL_RATE_11M_INDEX_TABLE; /* CCK shouldn't fall back to OFDM... */ table[index].next_rate_index = IWL_RATE_5M_INDEX_TABLE; } break; default: WARN_ON(1); break; } /* Update the rate scaling for control frame Tx */ rate_cmd.table_id = 0; rc = iwl_send_cmd_pdu(priv, REPLY_RATE_SCALE, sizeof(rate_cmd), &rate_cmd); if (rc) return rc; /* Update the rate scaling for data frame Tx */ rate_cmd.table_id = 1; return iwl_send_cmd_pdu(priv, REPLY_RATE_SCALE, sizeof(rate_cmd), &rate_cmd); } /* Called when initializing driver */ int iwl3945_hw_set_hw_params(struct iwl_priv *priv) { memset((void *)&priv->hw_params, 0, sizeof(struct iwl_hw_params)); priv->shared_virt = pci_alloc_consistent(priv->pci_dev, sizeof(struct iwl3945_shared), &priv->shared_phys); if (!priv->shared_virt) { IWL_ERR(priv, "failed to allocate pci memory\n"); mutex_unlock(&priv->mutex); return -ENOMEM; } /* Assign number of Usable TX queues */ priv->hw_params.max_txq_num = TFD_QUEUE_MAX; priv->hw_params.tfd_size = sizeof(struct iwl3945_tfd); priv->hw_params.rx_buf_size = IWL_RX_BUF_SIZE_3K; priv->hw_params.max_pkt_size = 2342; priv->hw_params.max_rxq_size = RX_QUEUE_SIZE; priv->hw_params.max_rxq_log = RX_QUEUE_SIZE_LOG; priv->hw_params.max_stations = IWL3945_STATION_COUNT; priv->hw_params.bcast_sta_id = IWL3945_BROADCAST_ID; priv->hw_params.rx_wrt_ptr_reg = FH39_RSCSR_CHNL0_WPTR; return 0; } unsigned int iwl3945_hw_get_beacon_cmd(struct iwl_priv *priv, struct iwl3945_frame *frame, u8 rate) { struct iwl3945_tx_beacon_cmd *tx_beacon_cmd; unsigned int frame_size; tx_beacon_cmd = (struct iwl3945_tx_beacon_cmd *)&frame->u; memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd)); tx_beacon_cmd->tx.sta_id = priv->hw_params.bcast_sta_id; tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE; frame_size = iwl3945_fill_beacon_frame(priv, tx_beacon_cmd->frame, sizeof(frame->u) - sizeof(*tx_beacon_cmd)); BUG_ON(frame_size > MAX_MPDU_SIZE); tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size); tx_beacon_cmd->tx.rate = rate; tx_beacon_cmd->tx.tx_flags = (TX_CMD_FLG_SEQ_CTL_MSK | TX_CMD_FLG_TSF_MSK); /* supp_rates[0] == OFDM start at IWL_FIRST_OFDM_RATE*/ tx_beacon_cmd->tx.supp_rates[0] = (IWL_OFDM_BASIC_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF; tx_beacon_cmd->tx.supp_rates[1] = (IWL_CCK_BASIC_RATES_MASK & 0xF); return sizeof(struct iwl3945_tx_beacon_cmd) + frame_size; } void iwl3945_hw_rx_handler_setup(struct iwl_priv *priv) { priv->rx_handlers[REPLY_TX] = iwl3945_rx_reply_tx; priv->rx_handlers[REPLY_3945_RX] = iwl3945_rx_reply_rx; } void iwl3945_hw_setup_deferred_work(struct iwl_priv *priv) { INIT_DELAYED_WORK(&priv->thermal_periodic, iwl3945_bg_reg_txpower_periodic); } void iwl3945_hw_cancel_deferred_work(struct iwl_priv *priv) { cancel_delayed_work(&priv->thermal_periodic); } /* check contents of special bootstrap uCode SRAM */ static int iwl3945_verify_bsm(struct iwl_priv *priv) { __le32 *image = priv->ucode_boot.v_addr; u32 len = priv->ucode_boot.len; u32 reg; u32 val; IWL_DEBUG_INFO(priv, "Begin verify bsm\n"); /* verify BSM SRAM contents */ val = iwl_read_prph(priv, BSM_WR_DWCOUNT_REG); for (reg = BSM_SRAM_LOWER_BOUND; reg < BSM_SRAM_LOWER_BOUND + len; reg += sizeof(u32), image++) { val = iwl_read_prph(priv, reg); if (val != le32_to_cpu(*image)) { IWL_ERR(priv, "BSM uCode verification failed at " "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n", BSM_SRAM_LOWER_BOUND, reg - BSM_SRAM_LOWER_BOUND, len, val, le32_to_cpu(*image)); return -EIO; } } IWL_DEBUG_INFO(priv, "BSM bootstrap uCode image OK\n"); return 0; } /****************************************************************************** * * EEPROM related functions * ******************************************************************************/ /* * Clear the OWNER_MSK, to establish driver (instead of uCode running on * embedded controller) as EEPROM reader; each read is a series of pulses * to/from the EEPROM chip, not a single event, so even reads could conflict * if they weren't arbitrated by some ownership mechanism. Here, the driver * simply claims ownership, which should be safe when this function is called * (i.e. before loading uCode!). */ static int iwl3945_eeprom_acquire_semaphore(struct iwl_priv *priv) { _iwl_clear_bit(priv, CSR_EEPROM_GP, CSR_EEPROM_GP_IF_OWNER_MSK); return 0; } static void iwl3945_eeprom_release_semaphore(struct iwl_priv *priv) { return; } /** * iwl3945_load_bsm - Load bootstrap instructions * * BSM operation: * * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program * in special SRAM that does not power down during RFKILL. When powering back * up after power-saving sleeps (or during initial uCode load), the BSM loads * the bootstrap program into the on-board processor, and starts it. * * The bootstrap program loads (via DMA) instructions and data for a new * program from host DRAM locations indicated by the host driver in the * BSM_DRAM_* registers. Once the new program is loaded, it starts * automatically. * * When initializing the NIC, the host driver points the BSM to the * "initialize" uCode image. This uCode sets up some internal data, then * notifies host via "initialize alive" that it is complete. * * The host then replaces the BSM_DRAM_* pointer values to point to the * normal runtime uCode instructions and a backup uCode data cache buffer * (filled initially with starting data values for the on-board processor), * then triggers the "initialize" uCode to load and launch the runtime uCode, * which begins normal operation. * * When doing a power-save shutdown, runtime uCode saves data SRAM into * the backup data cache in DRAM before SRAM is powered down. * * When powering back up, the BSM loads the bootstrap program. This reloads * the runtime uCode instructions and the backup data cache into SRAM, * and re-launches the runtime uCode from where it left off. */ static int iwl3945_load_bsm(struct iwl_priv *priv) { __le32 *image = priv->ucode_boot.v_addr; u32 len = priv->ucode_boot.len; dma_addr_t pinst; dma_addr_t pdata; u32 inst_len; u32 data_len; int rc; int i; u32 done; u32 reg_offset; IWL_DEBUG_INFO(priv, "Begin load bsm\n"); /* make sure bootstrap program is no larger than BSM's SRAM size */ if (len > IWL39_MAX_BSM_SIZE) return -EINVAL; /* Tell bootstrap uCode where to find the "Initialize" uCode * in host DRAM ... host DRAM physical address bits 31:0 for 3945. * NOTE: iwl3945_initialize_alive_start() will replace these values, * after the "initialize" uCode has run, to point to * runtime/protocol instructions and backup data cache. */ pinst = priv->ucode_init.p_addr; pdata = priv->ucode_init_data.p_addr; inst_len = priv->ucode_init.len; data_len = priv->ucode_init_data.len; iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst); iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata); iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len); iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len); /* Fill BSM memory with bootstrap instructions */ for (reg_offset = BSM_SRAM_LOWER_BOUND; reg_offset < BSM_SRAM_LOWER_BOUND + len; reg_offset += sizeof(u32), image++) _iwl_write_prph(priv, reg_offset, le32_to_cpu(*image)); rc = iwl3945_verify_bsm(priv); if (rc) return rc; /* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */ iwl_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0); iwl_write_prph(priv, BSM_WR_MEM_DST_REG, IWL39_RTC_INST_LOWER_BOUND); iwl_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32)); /* Load bootstrap code into instruction SRAM now, * to prepare to load "initialize" uCode */ iwl_write_prph(priv, BSM_WR_CTRL_REG, BSM_WR_CTRL_REG_BIT_START); /* Wait for load of bootstrap uCode to finish */ for (i = 0; i < 100; i++) { done = iwl_read_prph(priv, BSM_WR_CTRL_REG); if (!(done & BSM_WR_CTRL_REG_BIT_START)) break; udelay(10); } if (i < 100) IWL_DEBUG_INFO(priv, "BSM write complete, poll %d iterations\n", i); else { IWL_ERR(priv, "BSM write did not complete!\n"); return -EIO; } /* Enable future boot loads whenever power management unit triggers it * (e.g. when powering back up after power-save shutdown) */ iwl_write_prph(priv, BSM_WR_CTRL_REG, BSM_WR_CTRL_REG_BIT_START_EN); return 0; } static struct iwl_hcmd_ops iwl3945_hcmd = { .rxon_assoc = iwl3945_send_rxon_assoc, .commit_rxon = iwl3945_commit_rxon, }; static struct iwl_lib_ops iwl3945_lib = { .txq_attach_buf_to_tfd = iwl3945_hw_txq_attach_buf_to_tfd, .txq_free_tfd = iwl3945_hw_txq_free_tfd, .txq_init = iwl3945_hw_tx_queue_init, .load_ucode = iwl3945_load_bsm, .apm_ops = { .init = iwl3945_apm_init, .reset = iwl3945_apm_reset, .stop = iwl3945_apm_stop, .config = iwl3945_nic_config, .set_pwr_src = iwl3945_set_pwr_src, }, .eeprom_ops = { .regulatory_bands = { EEPROM_REGULATORY_BAND_1_CHANNELS, EEPROM_REGULATORY_BAND_2_CHANNELS, EEPROM_REGULATORY_BAND_3_CHANNELS, EEPROM_REGULATORY_BAND_4_CHANNELS, EEPROM_REGULATORY_BAND_5_CHANNELS, EEPROM_REGULATORY_BAND_NO_FAT, EEPROM_REGULATORY_BAND_NO_FAT, }, .verify_signature = iwlcore_eeprom_verify_signature, .acquire_semaphore = iwl3945_eeprom_acquire_semaphore, .release_semaphore = iwl3945_eeprom_release_semaphore, .query_addr = iwlcore_eeprom_query_addr, }, .send_tx_power = iwl3945_send_tx_power, .is_valid_rtc_data_addr = iwl3945_hw_valid_rtc_data_addr, .post_associate = iwl3945_post_associate, .isr = iwl_isr_legacy, .config_ap = iwl3945_config_ap, }; static struct iwl_hcmd_utils_ops iwl3945_hcmd_utils = { .get_hcmd_size = iwl3945_get_hcmd_size, .build_addsta_hcmd = iwl3945_build_addsta_hcmd, }; static struct iwl_ops iwl3945_ops = { .lib = &iwl3945_lib, .hcmd = &iwl3945_hcmd, .utils = &iwl3945_hcmd_utils, }; static struct iwl_cfg iwl3945_bg_cfg = { .name = "3945BG", .fw_name_pre = IWL3945_FW_PRE, .ucode_api_max = IWL3945_UCODE_API_MAX, .ucode_api_min = IWL3945_UCODE_API_MIN, .sku = IWL_SKU_G, .eeprom_size = IWL3945_EEPROM_IMG_SIZE, .eeprom_ver = EEPROM_3945_EEPROM_VERSION, .ops = &iwl3945_ops, .mod_params = &iwl3945_mod_params, .use_isr_legacy = true }; static struct iwl_cfg iwl3945_abg_cfg = { .name = "3945ABG", .fw_name_pre = IWL3945_FW_PRE, .ucode_api_max = IWL3945_UCODE_API_MAX, .ucode_api_min = IWL3945_UCODE_API_MIN, .sku = IWL_SKU_A|IWL_SKU_G, .eeprom_size = IWL3945_EEPROM_IMG_SIZE, .eeprom_ver = EEPROM_3945_EEPROM_VERSION, .ops = &iwl3945_ops, .mod_params = &iwl3945_mod_params, .use_isr_legacy = true }; struct pci_device_id iwl3945_hw_card_ids[] = { {IWL_PCI_DEVICE(0x4222, 0x1005, iwl3945_bg_cfg)}, {IWL_PCI_DEVICE(0x4222, 0x1034, iwl3945_bg_cfg)}, {IWL_PCI_DEVICE(0x4222, 0x1044, iwl3945_bg_cfg)}, {IWL_PCI_DEVICE(0x4227, 0x1014, iwl3945_bg_cfg)}, {IWL_PCI_DEVICE(0x4222, PCI_ANY_ID, iwl3945_abg_cfg)}, {IWL_PCI_DEVICE(0x4227, PCI_ANY_ID, iwl3945_abg_cfg)}, {0} }; MODULE_DEVICE_TABLE(pci, iwl3945_hw_card_ids);