Kernel driver lm75 ================== Supported chips: * National Semiconductor LM75 Prefix: 'lm75' Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ * National Semiconductor LM75A Prefix: 'lm75a' Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505 Prefixes: 'ds75', 'ds1775', 'ds7505' Addresses scanned: none Datasheet: Publicly available at the Maxim website http://www.maximintegrated.com/ * Maxim MAX6625, MAX6626 Prefixes: 'max6625', 'max6626' Addresses scanned: none Datasheet: Publicly available at the Maxim website http://www.maxim-ic.com/ * Microchip (TelCom) TCN75 Prefix: 'tcn75' Addresses scanned: none Datasheet: Publicly available at the Microchip website http://www.microchip.com/ * Microchip MCP9800, MCP9801, MCP9802, MCP9803 Prefix: 'mcp980x' Addresses scanned: none Datasheet: Publicly available at the Microchip website http://www.microchip.com/ * Analog Devices ADT75 Prefix: 'adt75' Addresses scanned: none Datasheet: Publicly available at the Analog Devices website http://www.analog.com/adt75 * ST Microelectronics STDS75 Prefix: 'stds75' Addresses scanned: none Datasheet: Publicly available at the ST website http://www.st.com/internet/analog/product/121769.jsp * Texas Instruments TMP100, TMP101, TMP105, TMP112, TMP75, TMP75C, TMP175, TMP275 Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp112', 'tmp175', 'tmp75', 'tmp75c', 'tmp275' Addresses scanned: none Datasheet: Publicly available at the Texas Instruments website http://www.ti.com/product/tmp100 http://www.ti.com/product/tmp101 http://www.ti.com/product/tmp105 http://www.ti.com/product/tmp112 http://www.ti.com/product/tmp75 http://www.ti.com/product/tmp75c http://www.ti.com/product/tmp175 http://www.ti.com/product/tmp275 * NXP LM75B Prefix: 'lm75b' Addresses scanned: none Datasheet: Publicly available at the NXP website http://www.nxp.com/documents/data_sheet/LM75B.pdf Author: Frodo Looijaard <frodol@dds.nl> Description ----------- The LM75 implements one temperature sensor. Limits can be set through the Overtemperature Shutdown register and Hysteresis register. Each value can be set and read to half-degree accuracy. An alarm is issued (usually to a connected LM78) when the temperature gets higher then the Overtemperature Shutdown value; it stays on until the temperature falls below the Hysteresis value. All temperatures are in degrees Celsius, and are guaranteed within a range of -55 to +125 degrees. The driver caches the values for a period varying between 1 second for the slowest chips and 125 ms for the fastest chips; reading it more often will do no harm, but will return 'old' values. The original LM75 was typically used in combination with LM78-like chips on PC motherboards, to measure the temperature of the processor(s). Clones are now used in various embedded designs. The LM75 is essentially an industry standard; there may be other LM75 clones not listed here, with or without various enhancements, that are supported. The clones are not detected by the driver, unless they reproduce the exact register tricks of the original LM75, and must therefore be instantiated explicitly. Higher resolution up to 12-bit is supported by this driver, other specific enhancements are not. The LM77 is not supported, contrary to what we pretended for a long time. Both chips are simply not compatible, value encoding differs.