From 5ca7d1ca77dc23934504b95a96d2660d345f83c2 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Thu, 5 Jan 2017 14:48:07 -0600 Subject: net: phy: dp83867: fix irq generation For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be programmed as an interrupt output instead of a Powerdown input in Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The current driver doesn't do this and as result IRQs will not be generated by DP83867 phy even if they are properly configured in DT. Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867 driver will work properly in interrupt enabled mode. Signed-off-by: Grygorii Strashko Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/dp83867.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'drivers/net/phy') diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c index 1b639242f9e2..e84ae084e259 100644 --- a/drivers/net/phy/dp83867.c +++ b/drivers/net/phy/dp83867.c @@ -29,6 +29,7 @@ #define MII_DP83867_MICR 0x12 #define MII_DP83867_ISR 0x13 #define DP83867_CTRL 0x1f +#define DP83867_CFG3 0x1e /* Extended Registers */ #define DP83867_RGMIICTL 0x0032 @@ -98,6 +99,8 @@ static int dp83867_config_intr(struct phy_device *phydev) micr_status |= (MII_DP83867_MICR_AN_ERR_INT_EN | MII_DP83867_MICR_SPEED_CHNG_INT_EN | + MII_DP83867_MICR_AUTONEG_COMP_INT_EN | + MII_DP83867_MICR_LINK_STS_CHNG_INT_EN | MII_DP83867_MICR_DUP_MODE_CHNG_INT_EN | MII_DP83867_MICR_SLEEP_MODE_CHNG_INT_EN); @@ -214,6 +217,13 @@ static int dp83867_config_init(struct phy_device *phydev) } } + /* Enable Interrupt output INT_OE in CFG3 register */ + if (phy_interrupt_is_valid(phydev)) { + val = phy_read(phydev, DP83867_CFG3); + val |= BIT(7); + phy_write(phydev, DP83867_CFG3, val); + } + return 0; } -- cgit v1.2.3 From 811a919135b980bac8009d042acdccf10dc1ef5e Mon Sep 17 00:00:00 2001 From: Zefir Kurtisi Date: Fri, 6 Jan 2017 12:14:48 +0100 Subject: phy state machine: failsafe leave invalid RUNNING state While in RUNNING state, phy_state_machine() checks for link changes by comparing phydev->link before and after calling phy_read_status(). This works as long as it is guaranteed that phydev->link is never changed outside the phy_state_machine(). If in some setups this happens, it causes the state machine to miss a link loss and remain RUNNING despite phydev->link being 0. This has been observed running a dsa setup with a process continuously polling the link states over ethtool each second (SNMPD RFC-1213 agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to call phy_read_status() and with that modify the link status - and with that bricking the phy state machine. This patch adds a fail-safe check while in RUNNING, which causes to move to CHANGELINK when the link is gone and we are still RUNNING. Signed-off-by: Zefir Kurtisi Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/phy.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'drivers/net/phy') diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 25f93a98863b..48da6e93c3f7 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -1065,6 +1065,15 @@ void phy_state_machine(struct work_struct *work) if (old_link != phydev->link) phydev->state = PHY_CHANGELINK; } + /* + * Failsafe: check that nobody set phydev->link=0 between two + * poll cycles, otherwise we won't leave RUNNING state as long + * as link remains down. + */ + if (!phydev->link && phydev->state == PHY_RUNNING) { + phydev->state = PHY_CHANGELINK; + phydev_err(phydev, "no link in PHY_RUNNING\n"); + } break; case PHY_CHANGELINK: err = phy_read_status(phydev); -- cgit v1.2.3