From 56dbe2c290bc580ac0774e163133c2ed84ecb8f0 Mon Sep 17 00:00:00 2001 From: Yanteng Si Date: Wed, 7 Aug 2024 21:48:55 +0800 Subject: net: stmmac: dwmac-loongson: Add Loongson GNET support The new generation Loongson LS2K2000 SoC and LS7A2000 chipset are equipped with the network controllers called Loongson GNET. It's the single and multi DMA-channels Loongson GMAC but with a PHY attached. Here is the summary of the DW GMAC features the controller has: DW GMAC IP-core: v3.73a Speeds: 10/100/1000Mbps Duplex: Full (both versions), Half (LS2K2000 GNET only) DMA-descriptors type: enhanced L3/L4 filters availability: Y VLAN hash table filter: Y PHY-interface: GMII (PHY is integrated into the chips) Remote Wake-up support: Y Mac Management Counters (MMC): Y Number of additional MAC addresses: 5 MAC Hash-based filter: Y Hash Table Size: 256 AV feature: Y (LS2K2000 GNET only) DMA channels: 8 (LS2K2000 GNET), 1 (LS7A2000 GNET) Let's update the Loongson DWMAC driver to supporting the new Loongson GNET controller. The change is mainly trivial: the driver shall be bound to the PCIe device with DID 0x7a13, and the device-specific setup() method shall be called for it. The only peculiarity concerns the integrated PHY speed change procedure. The PHY has a weird problem with switching from the low speeds to 1000Mbps mode. The speedup procedure requires the PHY-link re-negotiation. So the suggested change provide the device-specific fix_mac_speed() method to overcome the problem. Signed-off-by: Feiyang Chen Signed-off-by: Yinggang Gu Acked-by: Huacai Chen Reviewed-by: Serge Semin Signed-off-by: Yanteng Si Tested-by: Serge Semin Signed-off-by: Paolo Abeni --- .../net/ethernet/stmicro/stmmac/dwmac-loongson.c | 77 +++++++++++++++++++++- 1 file changed, 74 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c') diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c index 48c92ba826d9..949e349ef856 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c @@ -65,11 +65,13 @@ DMA_STATUS_MSK_COMMON_LOONGSON) #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 #define DWMAC_CORE_LS_MULTICHAN 0x10 /* Loongson custom ID */ #define CHANNEL_NUM 8 struct loongson_data { u32 loongson_id; + struct device *dev; }; struct stmmac_pci_info { @@ -147,6 +149,60 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .setup = loongson_gmac_data, }; +static void loongson_gnet_fix_speed(void *priv, unsigned int speed, + unsigned int mode) +{ + struct loongson_data *ld = (struct loongson_data *)priv; + struct net_device *ndev = dev_get_drvdata(ld->dev); + struct stmmac_priv *ptr = netdev_priv(ndev); + + /* The integrated PHY has a weird problem with switching from the low + * speeds to 1000Mbps mode. The speedup procedure requires the PHY-link + * re-negotiation. + */ + if (speed == SPEED_1000) { + if (readl(ptr->ioaddr + MAC_CTRL_REG) & + GMAC_CONTROL_PS) + /* Word around hardware bug, restart autoneg */ + phy_restart_aneg(ndev->phydev); + } +} + +static int loongson_gnet_data(struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + struct loongson_data *ld; + int i; + + ld = plat->bsp_priv; + + loongson_default_data(pdev, plat); + + if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) { + plat->rx_queues_to_use = CHANNEL_NUM; + plat->tx_queues_to_use = CHANNEL_NUM; + + /* Only channel 0 supports checksum, + * so turn off checksum to enable multiple channels. + */ + for (i = 1; i < CHANNEL_NUM; i++) + plat->tx_queues_cfg[i].coe_unsupported = 1; + } else { + plat->tx_queues_to_use = 1; + plat->rx_queues_to_use = 1; + } + + plat->phy_interface = PHY_INTERFACE_MODE_GMII; + plat->mdio_bus_data->phy_mask = ~(u32)BIT(2); + plat->fix_mac_speed = loongson_gnet_fix_speed; + + return 0; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, +}; + static void loongson_dwmac_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_dma_cfg *dma_cfg, @@ -279,8 +335,10 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv) struct mac_device_info *mac; struct stmmac_dma_ops *dma; struct loongson_data *ld; + struct pci_dev *pdev; ld = priv->plat->bsp_priv; + pdev = to_pci_dev(priv->device); mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); if (!mac) @@ -290,7 +348,7 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv) if (!dma) return NULL; - /* The Loongson GMAC devices are based on the DW GMAC + /* The Loongson GMAC and GNET devices are based on the DW GMAC * v3.50a and v3.73a IP-cores. But the HW designers have changed the * GMAC_VERSION.SNPSVER field to the custom 0x10 value on the * network controllers with the multi-channels feature @@ -319,8 +377,19 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv) if (mac->multicast_filter_bins) mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins); - /* Loongson GMAC doesn't support the flow control. */ - mac->link.caps = MAC_10 | MAC_100 | MAC_1000; + /* Loongson GMAC doesn't support the flow control. LS2K2000 + * GNET doesn't support the half-duplex link mode. + */ + if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) { + mac->link.caps = MAC_10 | MAC_100 | MAC_1000; + } else { + if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10 | MAC_100 | MAC_1000; + else + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10FD | MAC_100FD | MAC_1000FD; + } mac->link.duplex = GMAC_CONTROL_DM; mac->link.speed10 = GMAC_CONTROL_PS; @@ -497,6 +566,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id plat->bsp_priv = ld; plat->setup = loongson_dwmac_setup; + ld->dev = &pdev->dev; ld->loongson_id = readl(res.addr + GMAC_VERSION) & 0xff; info = (struct stmmac_pci_info *)id->driver_data; @@ -597,6 +667,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table); -- cgit v1.2.3