From f4dfef75adb12fec7693d0c469e2de6c7d45e975 Mon Sep 17 00:00:00 2001 From: Prabhakar Kushwaha Date: Wed, 15 Aug 2012 20:43:52 +0530 Subject: powerpc: Update Integrated Flash controller device tree bindings Freescale's Integrated Flash controller (IFC) may have one or two interrupts. In case of single interrupt line, it will cover all IFC interrupts. Update this information in IFC device tree bindings Signed-off-by: Prabhakar Kushwaha Signed-off-by: Kumar Gala --- Documentation/devicetree/bindings/powerpc/fsl/ifc.txt | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt index 939a26d541f6..d5e370450ac0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt @@ -12,9 +12,12 @@ Properties: - #size-cells : Either one or two, depending on how large each chipselect can be. - reg : Offset and length of the register set for the device -- interrupts : IFC has two interrupts. The first one is the "common" - interrupt(CM_EVTER_STAT), and second is the NAND interrupt - (NAND_EVTER_STAT). +- interrupts: IFC may have one or two interrupts. If two interrupt + specifiers are present, the first is the "common" + interrupt (CM_EVTER_STAT), and the second is the NAND + interrupt (NAND_EVTER_STAT). If there is only one, + that interrupt reports both types of event. + - ranges : Each range corresponds to a single chipselect, and covers the entire access window as configured. -- cgit v1.2.3 From 00e4b1975bbcd10445808cec0a3a1442e8deca53 Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Fri, 24 Aug 2012 05:39:39 +0000 Subject: dt/misc: add bindings documentation for ifm camera sensor interface IFM O2D cameras use special sensor bus interface glue-logic to connect camera sensors to mpc5200 LocalPlus bus. Add device tree bindings documentation for it. Signed-off-by: Anatolij Gustschin --- Documentation/devicetree/bindings/misc/ifm-csi.txt | 41 ++++++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 Documentation/devicetree/bindings/misc/ifm-csi.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt new file mode 100644 index 000000000000..5bdfffb0b9f7 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt @@ -0,0 +1,41 @@ +IFM camera sensor interface on mpc5200 LocalPlus bus + +Required properties: +- compatible: "ifm,o2d-csi" +- reg: specifies sensor chip select number and associated address range +- interrupts: external interrupt line number and interrupt sense mode + of the interrupt line signaling frame valid events +- gpios: three gpio-specifiers for "capture", "reset" and "master enable" + GPIOs (strictly in this order). +- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor + clock generator. This node is usually a general purpose timer controller. +- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25) +- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16) +- ifm,csi-wait-cycles: sensor bus wait cycles + +Optional properties: +- ifm,csi-byte-swap: if this property is present, the byte swapping on + the bus will be enabled. + +Example: + + csi@3,0 { + compatible = "ifm,o2d-csi"; + reg = <3 0 0x00100000>; /* CS 3, 1 MiB range */ + interrupts = <1 1 2>; /* IRQ1, edge falling */ + + ifm,csi-clk-handle = <&timer7>; + gpios = <&gpio_simple 23 0 /* image_capture */ + &gpio_simple 26 0 /* image_reset */ + &gpio_simple 29 0>; /* image_master_en */ + + ifm,csi-addr-bus-width = <24>; + ifm,csi-data-bus-width = <8>; + ifm,csi-wait-cycles = <0>; + }; + +The base address of the used chip select is specified in the +ranges property of the parent localbus node, for example: + + ranges = <0 0 0xff000000 0x01000000 + 3 0 0xe3000000 0x00100000>; -- cgit v1.2.3