From c794f6a09a251e229b122082eff1f85b994d2bca Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Wed, 14 Oct 2015 22:35:46 +0300 Subject: ARM: shmobile: porter: add HS-USB DT support Enable HS-USB device for the Porter board, defining the GPIO that the driver should check when probing (which is the ID output from MAX3355 OTG chip). Note that there will be pinctrl-related error messages if both internal PCI and HS-USB drivers are enabled but they should be just ignored. This patch is analogous to the commit 6f4f7156e0e6 ("ARM: shmobile: henninger: enable HS-USB") as there are no differences between the boards in this respect. Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-porter.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index fe0f12fc02a1..9f9ffe322d17 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -269,6 +269,14 @@ status = "okay"; }; +&hsusb { + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; + + status = "okay"; + renesas,enable-gpio = <&gpio5 31 GPIO_ACTIVE_HIGH>; +}; + &usbphy { status = "okay"; }; -- cgit v1.2.3 From b6be6b2f3be270cbd53fb13706c32500f6cd1432 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 16 Oct 2015 16:05:15 +0200 Subject: ARM: shmobile: r8a7794 dtsi: Remove bogus imp_clk node R-Car E2 does not have an IMP core or an IMP clock. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 8 -------- 1 file changed, 8 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index a9977d6ee81a..6fc1acff507f 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -879,14 +879,6 @@ clock-mult = <1>; clock-output-names = "m2"; }; - imp_clk: imp_clk { - compatible = "fixed-factor-clock"; - clocks = <&cpg_clocks R8A7794_CLK_PLL1>; - #clock-cells = <0>; - clock-div = <4>; - clock-mult = <1>; - clock-output-names = "imp"; - }; rclk_clk: rclk_clk { compatible = "fixed-factor-clock"; clocks = <&cpg_clocks R8A7794_CLK_PLL1>; -- cgit v1.2.3 From 5d2ac865a609ff1c5a5228c8721e7ae06f5f7b72 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 16 Oct 2015 16:05:16 +0200 Subject: ARM: shmobile: r8a7791 dtsi: Remove bogus imp_clk node R-Car M2-W does not have an IMP core or an IMP clock. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 8 -------- 1 file changed, 8 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 3b8e26dde36d..57029d3fe1e5 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1163,14 +1163,6 @@ clock-mult = <1>; clock-output-names = "m2"; }; - imp_clk: imp_clk { - compatible = "fixed-factor-clock"; - clocks = <&cpg_clocks R8A7791_CLK_PLL1>; - #clock-cells = <0>; - clock-div = <4>; - clock-mult = <1>; - clock-output-names = "imp"; - }; rclk_clk: rclk_clk { compatible = "fixed-factor-clock"; clocks = <&cpg_clocks R8A7791_CLK_PLL1>; -- cgit v1.2.3 From 761b11e141366743a5c179a0f94c237d0ba9667c Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Fri, 16 Oct 2015 14:37:01 -0700 Subject: ARM: shmobile: silk: add SDHI1 DT support Define the SILK board dependent part of the SDHI1 (connected to micro-SD slot) device nodes along with the necessary voltage regulators. Based on the original patch by Vladimir Barinov . Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-silk.dts | 40 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index 48ff3e2958ae..a49942b626c8 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -12,6 +12,7 @@ /dts-v1/; #include "r8a7794.dtsi" +#include / { model = "SILK"; @@ -39,6 +40,30 @@ regulator-boot-on; regulator-always-on; }; + + vcc_sdhi1: regulator@3 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI1 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi1: regulator@4 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI1 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; }; &extal_clk { @@ -71,6 +96,11 @@ renesas,function = "mmc"; }; + sdhi1_pins: sd1 { + renesas,groups = "sdhi1_data4", "sdhi1_ctrl"; + renesas,function = "sdhi1"; + }; + qspi_pins: spi0 { renesas,groups = "qspi_ctrl", "qspi_data4"; renesas,function = "qspi"; @@ -147,6 +177,16 @@ status = "okay"; }; +&sdhi1 { + pinctrl-0 = <&sdhi1_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi1>; + vqmmc-supply = <&vccq_sdhi1>; + cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + &qspi { pinctrl-0 = <&qspi_pins>; pinctrl-names = "default"; -- cgit v1.2.3 From 0cc16889e77a95568806b1e45af104f75547eac9 Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:11 +0100 Subject: ARM: dts: shmobile/r8a7xxx: replace gpio-key, wakeup with wakeup-source property Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Signed-off-by: Sudeep Holla Acked-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +- arch/arm/boot/dts/r8a7740-armadillo800eva.dts | 2 +- arch/arm/boot/dts/r8a7790-lager.dts | 8 ++++---- arch/arm/boot/dts/r8a7791-koelsch.dts | 22 +++++++++++----------- arch/arm/boot/dts/sh73a0-kzm9g.dts | 2 +- 5 files changed, 18 insertions(+), 18 deletions(-) diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index a4c425923c05..9b7eabd3eba3 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -110,7 +110,7 @@ gpios = <&pfc 324 GPIO_ACTIVE_LOW>; linux,code = ; label = "S16"; - gpio-key,wakeup; + wakeup-source; }; menu-key { diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts index 105d9c95de4a..78a21f2828df 100644 --- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts +++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts @@ -85,7 +85,7 @@ gpios = <&pfc 99 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW3"; - gpio-key,wakeup; + wakeup-source; }; back-key { diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index c553abd711ee..e2174d816e78 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -77,28 +77,28 @@ button@1 { linux,code = ; label = "SW2-1"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; }; button@2 { linux,code = ; label = "SW2-2"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; }; button@3 { linux,code = ; label = "SW2-3"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; }; button@4 { linux,code = ; label = "SW2-4"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; }; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index fc44ea361a4b..98da99d1b7dc 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -79,77 +79,77 @@ gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW2-1"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-2 { gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW2-2"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-3 { gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW2-3"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-4 { gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW2-4"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-a { gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW30"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-b { gpios = <&gpio7 1 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW31"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-c { gpios = <&gpio7 2 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW32"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-d { gpios = <&gpio7 3 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW33"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-e { gpios = <&gpio7 4 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW34"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-f { gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW35"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; key-g { gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW36"; - gpio-key,wakeup; + wakeup-source; debounce-interval = <20>; }; }; diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts index 7fc5602810ad..aa8bae3b8fcf 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts @@ -147,7 +147,7 @@ gpios = <&pcf8575 14 GPIO_ACTIVE_LOW>; linux,code = ; label = "SW1"; - gpio-key,wakeup; + wakeup-source; }; }; -- cgit v1.2.3 From 56a2182f6ada123759041bf28d066bb509fe358b Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Thu, 22 Oct 2015 02:04:41 +0300 Subject: ARM: shmobile: r8a7790: fix "gpio-ranges" props On R8A7790, GPIO banks 1 and 2 are missing pins 30 and 31. Correct the "gpio-ranges" properties of the corresponding device nodes. Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index ae5eb281d43a..b545fef3f7db 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -143,7 +143,7 @@ interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; - gpio-ranges = <&pfc 0 32 32>; + gpio-ranges = <&pfc 0 32 30>; #interrupt-cells = <2>; interrupt-controller; clocks = <&mstp9_clks R8A7790_CLK_GPIO1>; @@ -156,7 +156,7 @@ interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; - gpio-ranges = <&pfc 0 64 32>; + gpio-ranges = <&pfc 0 64 30>; #interrupt-cells = <2>; interrupt-controller; clocks = <&mstp9_clks R8A7790_CLK_GPIO2>; -- cgit v1.2.3 From 1329f6d0f6a502089ed00038493985f2a4d97006 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Thu, 22 Oct 2015 02:05:19 +0300 Subject: ARM: shmobile: r8a7791: fix "gpio-ranges" props On R8A7791, GPIO banks 1 and 7 are missing pins 26 to 31. Correct the "gpio-ranges" properties of the GPIO1 node (GPIO7 is already correct). Signed-off-by: Sergei Shtylyov Tested-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 57029d3fe1e5..2bc54e359768 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -100,7 +100,7 @@ interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; - gpio-ranges = <&pfc 0 32 32>; + gpio-ranges = <&pfc 0 32 26>; #interrupt-cells = <2>; interrupt-controller; clocks = <&mstp9_clks R8A7791_CLK_GPIO1>; -- cgit v1.2.3 From 832d3e4c823be3c09e20b33793ac668c77ea5bd6 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sun, 18 Oct 2015 14:26:56 +0900 Subject: ARM: shmobile: r8a7794: Disable all IPMMU nodes by default The r8a7794 IPMMU nodes for MX and DS are currently lacking a line containing 'status = "disabled"', fix this by making sure they are disabled like all other IPMMU nodes. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 6fc1acff507f..018ff56470b6 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -1097,6 +1097,7 @@ interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, <0 199 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; + status = "disabled"; }; ipmmu_mp: mmu@ec680000 { @@ -1113,6 +1114,7 @@ interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; + status = "disabled"; }; ipmmu_gp: mmu@e62a0000 { -- cgit v1.2.3 From 098cb3a601e6a6afcf1d0c15bc939a57732242a4 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sun, 18 Oct 2015 14:35:41 +0900 Subject: ARM: shmobile: r8a7793: Add IPMMU nodes Add IPMMU nodes for the r8a7793 SoC. The IPMMU configuration for r8a7793 is identical to r8a7791 and includes SY0, SY1, DS, MP, MX, RT and GP. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 59 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index c4654047e684..fcafa87616fa 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -371,4 +371,63 @@ }; }; + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_rt: mmu@ffc80000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xffc80000 0 0x1000>; + interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_gp: mmu@e62a0000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe62a0000 0 0x1000>; + interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, + <0 261 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; }; -- cgit v1.2.3 From 0768fbad7fba1d2793cb4b57e30786e32d203948 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Wed, 28 Oct 2015 00:03:22 +0300 Subject: ARM: shmobile: porter: add CAN0 DT support Define the Porter board dependent part of the CAN0 device node. This patch is analogous to the commit 457acc4a6ce8 ("ARM: shmobile: henninger: add CAN0 DT support") as there are no differences between the boards in this respect. Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-porter.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index 9f9ffe322d17..3e198e7b3ee4 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -134,6 +134,11 @@ renesas,groups = "vin0_data8", "vin0_clk"; renesas,function = "vin0"; }; + + can0_pins: can0 { + renesas,groups = "can0_data"; + renesas,function = "can0"; + }; }; &scif0 { @@ -288,3 +293,10 @@ &pciec { status = "okay"; }; + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; -- cgit v1.2.3 From 2b06f1087062c516ac2851ce5038fdb035b19d4d Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Thu, 29 Oct 2015 00:34:29 +0300 Subject: ARM: shmobile: henninger: remove board DT The Henninger low cost board was never sold and so had no users outside Renesas (and Cogent Embedded). Instead Renesas has made the Porter board which has mostly similar hardware. Now that the Porter board support is on par with Henninger, we can remove the Henninger's device tree file. Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/Makefile | 1 - arch/arm/boot/dts/r8a7791-henninger.dts | 320 -------------------------------- 2 files changed, 321 deletions(-) delete mode 100644 arch/arm/boot/dts/r8a7791-henninger.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index d285d9816d9d..d3de3a447d72 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -530,7 +530,6 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \ r8a7778-bockw.dtb \ r8a7779-marzen.dtb \ r8a7790-lager.dtb \ - r8a7791-henninger.dtb \ r8a7791-koelsch.dtb \ r8a7791-porter.dtb \ r8a7793-gose.dtb \ diff --git a/arch/arm/boot/dts/r8a7791-henninger.dts b/arch/arm/boot/dts/r8a7791-henninger.dts deleted file mode 100644 index 655d1804e5e9..000000000000 --- a/arch/arm/boot/dts/r8a7791-henninger.dts +++ /dev/null @@ -1,320 +0,0 @@ -/* - * Device Tree Source for the Henninger board - * - * Copyright (C) 2014 Renesas Solutions Corp. - * Copyright (C) 2014 Cogent Embedded, Inc. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/dts-v1/; -#include "r8a7791.dtsi" -#include - -/ { - model = "Henninger"; - compatible = "renesas,henninger", "renesas,r8a7791"; - - aliases { - serial0 = &scif0; - }; - - chosen { - bootargs = "console=ttySC0,38400 ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif0; - }; - - memory@40000000 { - device_type = "memory"; - reg = <0 0x40000000 0 0x40000000>; - }; - - memory@200000000 { - device_type = "memory"; - reg = <2 0x00000000 0 0x40000000>; - }; - - vcc_sdhi0: regulator@0 { - compatible = "regulator-fixed"; - - regulator-name = "SDHI0 Vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vccq_sdhi0: regulator@1 { - compatible = "regulator-gpio"; - - regulator-name = "SDHI0 VccQ"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>; - gpios-states = <1>; - states = <3300000 1 - 1800000 0>; - }; - - vcc_sdhi2: regulator@2 { - compatible = "regulator-fixed"; - - regulator-name = "SDHI2 Vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vccq_sdhi2: regulator@3 { - compatible = "regulator-gpio"; - - regulator-name = "SDHI2 VccQ"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; - gpios-states = <1>; - states = <3300000 1 - 1800000 0>; - }; -}; - -&extal_clk { - clock-frequency = <20000000>; -}; - -&pfc { - scif0_pins: serial0 { - renesas,groups = "scif0_data_d"; - renesas,function = "scif0"; - }; - - ether_pins: ether { - renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; - renesas,function = "eth"; - }; - - phy1_pins: phy1 { - renesas,groups = "intc_irq0"; - renesas,function = "intc"; - }; - - sdhi0_pins: sd0 { - renesas,groups = "sdhi0_data4", "sdhi0_ctrl"; - renesas,function = "sdhi0"; - }; - - sdhi2_pins: sd2 { - renesas,groups = "sdhi2_data4", "sdhi2_ctrl"; - renesas,function = "sdhi2"; - }; - - i2c2_pins: i2c2 { - renesas,groups = "i2c2"; - renesas,function = "i2c2"; - }; - - qspi_pins: spi0 { - renesas,groups = "qspi_ctrl", "qspi_data4"; - renesas,function = "qspi"; - }; - - msiof0_pins: spi1 { - renesas,groups = "msiof0_clk", "msiof0_sync", "msiof0_rx", - "msiof0_tx"; - renesas,function = "msiof0"; - }; - - usb0_pins: usb0 { - renesas,groups = "usb0"; - renesas,function = "usb0"; - }; - - usb1_pins: usb1 { - renesas,groups = "usb1"; - renesas,function = "usb1"; - }; - - vin0_pins: vin0 { - renesas,groups = "vin0_data8", "vin0_clk"; - renesas,function = "vin0"; - }; - - can0_pins: can0 { - renesas,groups = "can0_data"; - renesas,function = "can0"; - }; -}; - -&scif0 { - pinctrl-0 = <&scif0_pins>; - pinctrl-names = "default"; - - status = "okay"; -}; - -ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; - pinctrl-names = "default"; - - phy-handle = <&phy1>; - renesas,ether-link-active-low; - status = "okay"; - - phy1: ethernet-phy@1 { - reg = <1>; - interrupt-parent = <&irqc0>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - micrel,led-mode = <1>; - }; -}; - -&sata0 { - status = "okay"; -}; - -&sdhi0 { - pinctrl-0 = <&sdhi0_pins>; - pinctrl-names = "default"; - - vmmc-supply = <&vcc_sdhi0>; - vqmmc-supply = <&vccq_sdhi0>; - cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; - status = "okay"; -}; - -&sdhi2 { - pinctrl-0 = <&sdhi2_pins>; - pinctrl-names = "default"; - - vmmc-supply = <&vcc_sdhi2>; - vqmmc-supply = <&vccq_sdhi2>; - cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>; - status = "okay"; -}; - -&i2c2 { - pinctrl-0 = <&i2c2_pins>; - pinctrl-names = "default"; - - status = "okay"; - clock-frequency = <400000>; - - composite-in@20 { - compatible = "adi,adv7180"; - reg = <0x20>; - remote = <&vin0>; - - port { - adv7180: endpoint { - bus-width = <8>; - remote-endpoint = <&vin0ep>; - }; - }; - }; -}; - -&qspi { - pinctrl-0 = <&qspi_pins>; - pinctrl-names = "default"; - - status = "okay"; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spansion,s25fl512s", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <30000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - m25p,fast-read; - - partition@0 { - label = "loader_prg"; - reg = <0x00000000 0x00040000>; - read-only; - }; - partition@40000 { - label = "user_prg"; - reg = <0x00040000 0x00400000>; - read-only; - }; - partition@440000 { - label = "flash_fs"; - reg = <0x00440000 0x03bc0000>; - }; - }; -}; - -&msiof0 { - pinctrl-0 = <&msiof0_pins>; - pinctrl-names = "default"; - - status = "okay"; - - pmic@0 { - compatible = "renesas,r2a11302ft"; - reg = <0>; - spi-max-frequency = <6000000>; - spi-cpol; - spi-cpha; - }; -}; - -&pci0 { - status = "okay"; - pinctrl-0 = <&usb0_pins>; - pinctrl-names = "default"; -}; - -&pci1 { - status = "okay"; - pinctrl-0 = <&usb1_pins>; - pinctrl-names = "default"; -}; - -&hsusb { - status = "okay"; - pinctrl-0 = <&usb0_pins>; - pinctrl-names = "default"; - renesas,enable-gpio = <&gpio5 31 GPIO_ACTIVE_HIGH>; -}; - -&usbphy { - status = "okay"; -}; - -&pcie_bus_clk { - status = "okay"; -}; - -&pciec { - status = "okay"; -}; - -/* composite video input */ -&vin0 { - status = "okay"; - pinctrl-0 = <&vin0_pins>; - pinctrl-names = "default"; - - port { - #address-cells = <1>; - #size-cells = <0>; - - vin0ep: endpoint { - remote-endpoint = <&adv7180>; - bus-width = <8>; - }; - }; -}; - -&can0 { - pinctrl-0 = <&can0_pins>; - pinctrl-names = "default"; - status = "okay"; -}; -- cgit v1.2.3 From 0fddfb5b609f3b037006bcd467c540a7968a2dc7 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 6 Nov 2015 16:30:48 +0900 Subject: ARM: shmobile: r8a7793: Add thermal device to DT Instantiate the thermal sensor in the r8a7793 device tree. Based on very similar work for the r8a7790 by Magnus Damm. Signed-off-by: Simon Horman Acked-by: Geert Uytterhoeven --- arch/arm/boot/dts/r8a7793.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index fcafa87616fa..6c7bae4318c9 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -53,6 +53,14 @@ interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; }; + thermal@e61f0000 { + compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal"; + reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7793_CLK_THERMAL>; + power-domains = <&cpg_clocks>; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <1 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, @@ -329,6 +337,14 @@ clock-indices = ; clock-output-names = "irqc"; }; + mstp5_clks: mstp5_clks@e6150144 { + compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; + clocks = <&extal_clk>; + #clock-cells = <1>; + clock-indices = ; + clock-output-names = "thermal"; + }; mstp7_clks: mstp7_clks@e615014c { compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; -- cgit v1.2.3 From c26455c7e3e4dd16caa4788fdd558e5fcee04742 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Mon, 9 Nov 2015 10:33:18 +0900 Subject: ARM: shmobile: r8a7793: Add PFC to DT Instantiate PFC device in r8a7793 DT. Based on similar work for the r8a7791 by Magnus Damm. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 6c7bae4318c9..4f6480f8845f 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -122,6 +122,12 @@ power-domains = <&cpg_clocks>; }; + pfc: pfc@e6060000 { + compatible = "renesas,pfc-r8a7793"; + reg = <0 0xe6060000 0 0x250>; + #gpio-range-cells = <3>; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a7793", "renesas,scif"; reg = <0 0xe6e60000 0 64>; -- cgit v1.2.3 From a81f05089aad81607bb4bcf9ccfb41ef4814d95e Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Mon, 9 Nov 2015 10:33:19 +0900 Subject: ARM: shmobile: gose: Configure PFC in DT Configure PFC for the already enabled scif and ethernet devices in the device tree for the gose board. Based on similar work for the koelsch board by Laurent Pinchart and Sergei Shtylyov. Signed-off-by: Simon Horman Acked-by: Laurent Pinchart --- arch/arm/boot/dts/r8a7793-gose.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index 96443ec5f6ab..1575ef759047 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -37,7 +37,32 @@ clock-frequency = <20000000>; }; +&pfc { + scif0_pins: serial0 { + renesas,groups = "scif0_data_d"; + renesas,function = "scif0"; + }; + + scif1_pins: serial1 { + renesas,groups = "scif1_data_d"; + renesas,function = "scif1"; + }; + + ether_pins: ether { + renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; + renesas,function = "eth"; + }; + + phy1_pins: phy1 { + renesas,groups = "intc_irq0"; + renesas,function = "intc"; + }; +}; + ðer { + pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-names = "default"; + phy-handle = <&phy1>; renesas,ether-link-active-low; status = "okay"; @@ -55,9 +80,15 @@ }; &scif0 { + pinctrl-0 = <&scif0_pins>; + pinctrl-names = "default"; + status = "okay"; }; &scif1 { + pinctrl-0 = <&scif1_pins>; + pinctrl-names = "default"; + status = "okay"; }; -- cgit v1.2.3 From 27fa0a6c55537f8d8656b9e59ae584b0b427232a Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 10 Nov 2015 09:35:06 +0100 Subject: ARM: shmobile: koelsch: Move SPI FLASH partitions to subnode As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support partitions in a special 'partitions' subnode"), having partitions as direct subnodes of an mtd device is discouraged: spi0.0: 'partitions' subnode not found on /spi@e6b10000/flash@0. Trying to parse direct subnodes as partitions. Hence move the SPI FLASH partitions to a "partitions" subnode. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-koelsch.dts | 33 ++++++++++++++++++--------------- 1 file changed, 18 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index 98da99d1b7dc..4ec2d1fba7c9 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -479,8 +479,6 @@ status = "okay"; flash: flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,s25fl512s", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <30000000>; @@ -490,19 +488,24 @@ spi-cpol; m25p,fast-read; - partition@0 { - label = "loader"; - reg = <0x00000000 0x00080000>; - read-only; - }; - partition@80000 { - label = "user"; - reg = <0x00080000 0x00580000>; - read-only; - }; - partition@600000 { - label = "flash"; - reg = <0x00600000 0x03a00000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00080000>; + read-only; + }; + partition@80000 { + label = "user"; + reg = <0x00080000 0x00580000>; + read-only; + }; + partition@600000 { + label = "flash"; + reg = <0x00600000 0x03a00000>; + }; }; }; }; -- cgit v1.2.3 From 38eb6a3aaf08cc8a70ef3d6a767521e2831a8a4c Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 12 Nov 2015 10:29:21 +0900 Subject: ARM: shmobile: r8a7793: Add DMAC devices to DT Instantiate the two system DMA controllers in the r8a7793 device tree. Based on similar work for the r8a7793 by Laurent Pinchart. Signed-off-by: Simon Horman Reviewed-by: Laurent Pinchart --- arch/arm/boot/dts/r8a7793.dtsi | 72 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 72 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 4f6480f8845f..187a82dc7d9f 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -128,6 +128,68 @@ #gpio-range-cells = <3>; }; + dmac0: dma-controller@e6700000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6700000 0 0x20000>; + interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH + 0 200 IRQ_TYPE_LEVEL_HIGH + 0 201 IRQ_TYPE_LEVEL_HIGH + 0 202 IRQ_TYPE_LEVEL_HIGH + 0 203 IRQ_TYPE_LEVEL_HIGH + 0 204 IRQ_TYPE_LEVEL_HIGH + 0 205 IRQ_TYPE_LEVEL_HIGH + 0 206 IRQ_TYPE_LEVEL_HIGH + 0 207 IRQ_TYPE_LEVEL_HIGH + 0 208 IRQ_TYPE_LEVEL_HIGH + 0 209 IRQ_TYPE_LEVEL_HIGH + 0 210 IRQ_TYPE_LEVEL_HIGH + 0 211 IRQ_TYPE_LEVEL_HIGH + 0 212 IRQ_TYPE_LEVEL_HIGH + 0 213 IRQ_TYPE_LEVEL_HIGH + 0 214 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7793_CLK_SYS_DMAC0>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + #dma-cells = <1>; + dma-channels = <15>; + }; + + dmac1: dma-controller@e6720000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6720000 0 0x20000>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH + 0 216 IRQ_TYPE_LEVEL_HIGH + 0 217 IRQ_TYPE_LEVEL_HIGH + 0 218 IRQ_TYPE_LEVEL_HIGH + 0 219 IRQ_TYPE_LEVEL_HIGH + 0 308 IRQ_TYPE_LEVEL_HIGH + 0 309 IRQ_TYPE_LEVEL_HIGH + 0 310 IRQ_TYPE_LEVEL_HIGH + 0 311 IRQ_TYPE_LEVEL_HIGH + 0 312 IRQ_TYPE_LEVEL_HIGH + 0 313 IRQ_TYPE_LEVEL_HIGH + 0 314 IRQ_TYPE_LEVEL_HIGH + 0 315 IRQ_TYPE_LEVEL_HIGH + 0 316 IRQ_TYPE_LEVEL_HIGH + 0 317 IRQ_TYPE_LEVEL_HIGH + 0 318 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7793_CLK_SYS_DMAC1>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + #dma-cells = <1>; + dma-channels = <15>; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a7793", "renesas,scif"; reg = <0 0xe6e60000 0 64>; @@ -313,6 +375,16 @@ "tmu3", "tmu2", "cmt0", "tmu0", "vsp1-du1", "vsp1-du0", "vsps"; }; + mstp2_clks: mstp2_clks@e6150138 { + compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>; + clocks = <&zs_clk>, <&zs_clk>; + #clock-cells = <1>; + clock-indices = < + R8A7793_CLK_SYS_DMAC1 R8A7793_CLK_SYS_DMAC0 + >; + clock-output-names = "sys-dmac1", "sys-dmac0"; + }; mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; -- cgit v1.2.3 From 469352ad3c43e689c15cd396cbb750ee831ab63e Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 12 Nov 2015 10:29:22 +0900 Subject: ARM: shmobile: r8a7793: Add QSPI device to DT Instantiate the QSPI controller in the r8a7793 device tree. Based on similar work for the r8a7794 by Hisashi Nakamura and Sergei Shtylyov. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 187a82dc7d9f..aa9b64c14a09 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -18,6 +18,10 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + spi0 = &qspi; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -222,6 +226,20 @@ status = "disabled"; }; + qspi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7793", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7793_CLK_QSPI_MOD>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>; + dma-names = "tx", "rx"; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -463,6 +481,14 @@ "ipmmu_sgx", "vin2", "vin1", "vin0", "ether", "sata1", "sata0"; }; + mstp9_clks: mstp9_clks@e6150994 { + compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150994 0 4>, <0 0xe61509a4 0 4>; + clocks = <&cpg_clocks R8A7793_CLK_QSPI>; + #clock-cells = <1>; + clock-indices = ; + clock-output-names = "qspi_mod"; + }; }; ipmmu_sy0: mmu@e6280000 { -- cgit v1.2.3 From 6380d62a1b1ca498f2187c9702f1dec00ad527e0 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 12 Nov 2015 10:29:23 +0900 Subject: ARM: shmobile: gose: Add QSPI device to DT Enable the QSPI controller in the gose device tree. Based on similar work for the silk board by Vladimir Barinov and Sergei Shtylyov. Signed-off-by: Simon Horman Acked-by: Geert Uytterhoeven --- arch/arm/boot/dts/r8a7793-gose.dts | 43 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 43 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index 1575ef759047..d842ce77b7c8 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -57,6 +57,11 @@ renesas,groups = "intc_irq0"; renesas,function = "intc"; }; + + qspi_pins: spi0 { + renesas,groups = "qspi_ctrl", "qspi_data4"; + renesas,function = "qspi"; + }; }; ðer { @@ -92,3 +97,41 @@ status = "okay"; }; + +&qspi { + pinctrl-0 = <&qspi_pins>; + pinctrl-names = "default"; + + status = "okay"; + + flash@0 { + compatible = "spansion,s25fl512s", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + spi-cpol; + spi-cpha; + m25p,fast-read; + + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash"; + reg = <0x00440000 0x03bc0000>; + }; + }; + }; +}; -- cgit v1.2.3 From 1dbcfb228beadb4a243486506f3fe09b33b96f7d Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Mon, 2 Nov 2015 13:40:56 -0500 Subject: ARM: dts: NSP: Add PCI support Add PCI support to the Northstar Plus SoC. This uses the existing pcie-iproc driver. So, all that is needed is device tree entries in the DTS. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 74 +++++++++++++++++++++++++++++++++++++++- arch/arm/boot/dts/bcm958625k.dts | 12 +++++++ 2 files changed, 85 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 58aca277e4a7..85fb1c8a2421 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -96,7 +96,7 @@ axi { compatible = "simple-bus"; - ranges = <0x00000000 0x18000000 0x00001000>; + ranges = <0x00000000 0x18000000 0x00015000>; #address-cells = <1>; #size-cells = <1>; @@ -115,5 +115,77 @@ clock-frequency = <62499840>; status = "disabled"; }; + + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x12000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + + /* Note: The HW does not support I/O resources. So, + * only the memory resource range is being specified. + */ + ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>; + + status = "disabled"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x13000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + + /* Note: The HW does not support I/O resources. So, + * only the memory resource range is being specified. + */ + ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>; + + status = "disabled"; + }; + + pcie2: pcie@18014000 { + compatible = "brcm,iproc-pcie"; + reg = <0x14000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>; + + linux,pci-domain = <2>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + + /* Note: The HW does not support I/O resources. So, + * only the memory resource range is being specified. + */ + ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>; + + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts index 16303dbd35df..48592687cfeb 100644 --- a/arch/arm/boot/dts/bcm958625k.dts +++ b/arch/arm/boot/dts/bcm958625k.dts @@ -55,3 +55,15 @@ &uart1 { status = "okay"; }; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; -- cgit v1.2.3 From 41254754aa03ed8c223094799f1d3779c442aae4 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Mon, 2 Nov 2015 13:40:57 -0500 Subject: ARM: dts: NSP: Add NAND Support to DT Add NAND support to the device tree for the Broadcom Northstar Plus SoC. Since no driver changes are needed to enable this hardware, only the device tree changes are required to make this functional. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 16 +++++++++++++++- arch/arm/boot/dts/bcm958625k.dts | 38 ++++++++++++++++++++++++++++++++++++++ 2 files changed, 53 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 85fb1c8a2421..62bc86fca958 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -96,7 +96,7 @@ axi { compatible = "simple-bus"; - ranges = <0x00000000 0x18000000 0x00015000>; + ranges = <0x00000000 0x18000000 0x0011ba08>; #address-cells = <1>; #size-cells = <1>; @@ -187,5 +187,19 @@ status = "disabled"; }; + + nand: nand@18026000 { + compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1"; + reg = <0x026000 0x600>, + <0x11b408 0x600>, + <0x026f00 0x20>; + reg-names = "nand", "iproc-idm", "iproc-ext"; + interrupts = ; + + #address-cells = <1>; + #size-cells = <0>; + + brcm,nand-has-wp; + }; }; }; diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts index 48592687cfeb..b966955260fa 100644 --- a/arch/arm/boot/dts/bcm958625k.dts +++ b/arch/arm/boot/dts/bcm958625k.dts @@ -67,3 +67,41 @@ &pcie2 { status = "okay"; }; + +&nand { + nandcs@0 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + + brcm,nand-oob-sector-size = <27>; + + partition@0 { + label = "nboot"; + reg = <0x00000000 0x00200000>; + read-only; + }; + partition@1 { + label = "nenv"; + reg = <0x00200000 0x00400000>; + }; + partition@2 { + label = "nsystem"; + reg = <0x00600000 0x00a00000>; + }; + partition@3 { + label = "nrootfs"; + reg = <0x01000000 0x03000000>; + }; + partition@4 { + label = "ncustfs"; + reg = <0x04000000 0x3c000000>; + }; + }; +}; -- cgit v1.2.3 From 1a9d53cabaf4d3c57a65e7808a64eb7937abba11 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Mon, 2 Nov 2015 13:40:58 -0500 Subject: ARM: dts: NSP: Add TWD Support to DT Add support for the ARM TWD Timer and Watchdog to the Northstar Plus device tree. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 62bc86fca958..4bcdd28fd2ac 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -80,6 +80,22 @@ interrupts = ; clocks = <&periph_clk>; }; + + twd-timer@19020600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0x0600 0x20>; + interrupts = ; + clocks = <&periph_clk>; + }; + + twd-watchdog@19020620 { + compatible = "arm,cortex-a9-twd-wdt"; + reg = <0x0620 0x20>; + interrupts = ; + clocks = <&periph_clk>; + }; }; clocks { -- cgit v1.2.3 From 445c0f29c1d0b771afc3b888bf375d73bb661e73 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Mon, 2 Nov 2015 13:34:52 -0500 Subject: dt-bindings: Add new SoCs to bcm4708 DT bindings Add the 4708, 4709, and 53012 SoCs to the the documentation for the Broadcom Northstar device tree bindings. Signed-off-by: Jon Mason Acked-by: Hauke Mehrtens Acked-by: Scott Branden Acked-by: Rob Herring Signed-off-by: Florian Fainelli --- Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt index 6b0f49f6f499..8608a776caa7 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt @@ -5,4 +5,11 @@ Boards with the BCM4708 SoC shall have the following properties: Required root node property: +bcm4708 compatible = "brcm,bcm4708"; + +bcm4709 +compatible = "brcm,bcm4709"; + +bcm53012 +compatible = "brcm,bcm53012"; -- cgit v1.2.3 From ccf0b5e37115f8675455632f583d06ea94f43539 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Mon, 2 Nov 2015 13:34:53 -0500 Subject: ARM: dts: bcm5301x: Add BCM SVK DT files Add device tree files for Broadcom Northstar based SVKs. Since the bcm5301x.dtsi already exists, all that is necessary is the dts files to enable the UARTs. With these files, the SVKs are able to boot to shell. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/Makefile | 5 +++- arch/arm/boot/dts/bcm94708.dts | 56 +++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/bcm94709.dts | 56 +++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/bcm953012k.dts | 63 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 179 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/bcm94708.dts create mode 100644 arch/arm/boot/dts/bcm94709.dts create mode 100644 arch/arm/boot/dts/bcm953012k.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..eab8a7fb0341 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -75,7 +75,10 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-asus-rt-ac87u.dtb \ bcm4709-buffalo-wxr-1900dhp.dtb \ bcm4709-netgear-r7000.dtb \ - bcm4709-netgear-r8000.dtb + bcm4709-netgear-r8000.dtb \ + bcm94708.dtb \ + bcm94709.dtb \ + bcm953012k.dtb dtb-$(CONFIG_ARCH_BCM_63XX) += \ bcm963138dvt.dtb dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \ diff --git a/arch/arm/boot/dts/bcm94708.dts b/arch/arm/boot/dts/bcm94708.dts new file mode 100644 index 000000000000..251a486f2da6 --- /dev/null +++ b/arch/arm/boot/dts/bcm94708.dts @@ -0,0 +1,56 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + model = "NorthStar SVK (BCM94708)"; + compatible = "brcm,bcm94708", "brcm,bcm4708"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm94709.dts b/arch/arm/boot/dts/bcm94709.dts new file mode 100644 index 000000000000..b16cac92904f --- /dev/null +++ b/arch/arm/boot/dts/bcm94709.dts @@ -0,0 +1,56 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + model = "NorthStar SVK (BCM94709)"; + compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/bcm953012k.dts new file mode 100644 index 000000000000..05a985a20378 --- /dev/null +++ b/arch/arm/boot/dts/bcm953012k.dts @@ -0,0 +1,63 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + model = "NorthStar SVK (BCM953012K)"; + compatible = "brcm,bcm953012k", "brcm,brcm53012", "brcm,bcm4708"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x00000000 0x10000000>; + }; +}; + +&uart0 { + clock-frequency = <62499840>; + status = "okay"; +}; + +&uart1 { + clock-frequency = <62499840>; + status = "okay"; +}; -- cgit v1.2.3 From 250656b4bc442d8e8c264733241b7b083dabb1a8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 3 Nov 2015 15:20:31 +0100 Subject: ARM: ux500: push down Rohm TS to STUIB The Rohm touchscreen reset and IRQ lines were registered and configured at the HREF board level of the design, but it is an integral part of the UIB (User Interface Board). Fix this by pushing down the pin control node to the u8500 UIB file. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href-stuib.dtsi | 23 +++++++++++++++++++++++ arch/arm/boot/dts/ste-hrefv60plus.dtsi | 18 ------------------ 2 files changed, 23 insertions(+), 18 deletions(-) diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi index 78b75256c638..c3987ad06d79 100644 --- a/arch/arm/boot/dts/ste-href-stuib.dtsi +++ b/arch/arm/boot/dts/ste-href-stuib.dtsi @@ -114,6 +114,8 @@ rohm,touch-max-x = <384>; rohm,touch-max-y = <704>; rohm,flip-y; + pinctrl-names = "default"; + pinctrl-0 = <&touch_rohm_mode>; }; bu21013_tp@5d { @@ -124,6 +126,8 @@ rohm,touch-max-x = <384>; rohm,touch-max-y = <704>; rohm,flip-y; + pinctrl-names = "default"; + pinctrl-0 = <&touch_rohm_mode>; }; }; @@ -166,6 +170,25 @@ }; }; }; + touch { + touch_rohm_mode: touch_rohm { + /* + * ROHM touch screen uses GPIO 143 for + * RST1, GPIO 146 for RST2 and + * GPIO 67 for interrupts. Pull-up + * the IRQ line and drive both + * reset signals low. + */ + stuib_cfg1 { + pins = "GPIO143_D12", "GPIO146_D13"; + ste,config = <&gpio_out_lo>; + }; + stuib_cfg2 { + pins = "GPIO67_G2"; + ste,config = <&gpio_in_pu>; + }; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index 9c2387b34d0c..149a72e7e37a 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -43,7 +43,6 @@ <&vaudio_hf_hrefv60_mode>, <&gbf_hrefv60_mode>, <&hdtv_hrefv60_mode>, - <&touch_hrefv60_mode>, <&gpios_hrefv60_mode>; sdi0 { @@ -190,23 +189,6 @@ }; }; }; - touch { - touch_hrefv60_mode: touch_hrefv60 { - /* - * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and - * GPIO 67 for interrupts. Pull-up the IRQ line and drive both - * reset signals low. - */ - hrefv60_cfg1 { - pins = "GPIO143_D12", "GPIO146_D13"; - ste,config = <&gpio_out_lo>; - }; - hrefv60_cfg2 { - pins = "GPIO67_G2"; - ste,config = <&gpio_in_pu>; - }; - }; - }; mcde { lcd_hrefv60_mode: lcd_hrefv60 { /* -- cgit v1.2.3 From c80b4010d7e4a1ba2aa83928a659f4bd87c1019c Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 5 Nov 2015 10:18:14 +0100 Subject: ARM: ux500: Assign proper sensor IRQs for Snowball The Snowball gyro and magnetometer DRDY (data ready) lines are used as interrupt triggers by the IIO subsystem, triggering new data retrieveal on edges on this signal. Thus assign them as the primary interrupt in the device tree. The "other interrupt" coming out of the sensors is for alarms and similar complex events, the DRDY is for periodic measures, which is what we want. After this the generic_buffer tool from IIO tools gives a nice stream of readings after enabling the desired channels in sysfs. Cc: Denis Ciocca Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-snowball.dts | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index e80e42163883..08f82077b64d 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -281,7 +281,8 @@ vddio-supply = <&db8500_vsmps2_reg>; pinctrl-names = "default"; pinctrl-0 = <&magneto_snowball_mode>; - gpios = <&gpio5 5 0x4>; /* DRDY line */ + interrupt-parent = <&gpio5>; + interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */ }; l3g4200d@68 { /* Gyroscope */ @@ -292,9 +293,9 @@ vddio-supply = <&db8500_vsmps2_reg>; pinctrl-names = "default"; pinctrl-0 = <&gyro_snowball_mode>; - gpios = <&gpio5 6 0x4>; /* DRDY line */ interrupt-parent = <&gpio5>; - interrupts = <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */ + interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ + <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */ }; lsp001wm@5c { /* Barometer/pressure sensor */ -- cgit v1.2.3 From 506822eaf1383c1d173e72cc318834e71ad23bff Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:15 +0100 Subject: ARM: ux500: replace legacy *,wakeup property with wakeup-source Though the keyboard and other driver will continue to support the legacy "gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup source, "wakeup-source" is the new standard binding. This patch replaces all the legacy wakeup properties with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Signed-off-by: Sudeep Holla Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 2 +- arch/arm/boot/dts/ste-nomadik-s8815.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 0e1c96943d47..3228119f91d1 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -66,7 +66,7 @@ keypad,num-columns = <8>; keypad,num-rows = <8>; linux,no-autorepeat; - linux,wakeup; + wakeup-source; linux,keymap = <0x0301006b 0x04010066 0x06040072 diff --git a/arch/arm/boot/dts/ste-nomadik-s8815.dts b/arch/arm/boot/dts/ste-nomadik-s8815.dts index 35282c0105c6..789329030658 100644 --- a/arch/arm/boot/dts/ste-nomadik-s8815.dts +++ b/arch/arm/boot/dts/ste-nomadik-s8815.dts @@ -163,7 +163,7 @@ label = "user_button"; gpios = <&gpio0 3 0x1>; linux,code = <1>; /* KEY_ESC */ - gpio-key,wakeup; + wakeup-source; pinctrl-names = "default"; pinctrl-0 = <&user_button_default_mode>; }; -- cgit v1.2.3 From e04a61c04a4ac242682820be7c89da5dbb183851 Mon Sep 17 00:00:00 2001 From: Adam Sampson Date: Fri, 23 Oct 2015 23:36:27 +0100 Subject: ARM: sun7i: dt: Enable audio codec on pcDuino V3 Nano The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is wired for headphone plug detection: it reads 0 when nothing's plugged in, and 1 when a plug is inserted. LINEINL/R and FMINL/R are not connected. Signed-off-by: Adam Sampson Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts index 1757a6ad74e9..ddac7328b852 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts @@ -82,6 +82,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; -- cgit v1.2.3 From 329f25b343c5fdd74da7a4c0520b24a732993ba8 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 23 Oct 2015 12:56:12 +0200 Subject: arm: sun7i: Add sun7i-a20-icnova-swac.dts This baseboard from SWAC is equipped with the ICnova-A20 SoM from Incircuit. This board is equipped with the following interfaces / devices: - 512 MiB SDRAM - 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR) - USB host - LCD 800x480 - HDMI - CAN Note that the NAND support is still missing. As its currently not supported in mainline for sunxi and especially for these MLC devices. The original plan was to also provide a dtsi for the ICnova SoM, to put all the SoM internal nodes / properties there. But as I don't have a clear overview of the SoM specific and baseboard specific differences, I'm putting all in one dts for now. Once somebody pushed support for some other baseboard using the A20 SoM from Incircuit (e.g. the ADB4006 reference design), this should be separated. Signed-off-by: Stefan Roese Cc: Marcus Heuer [maxime: Fixed CPU regulator upper voltage boundary] Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun7i-a20-icnova-swac.dts | 169 ++++++++++++++++++++++++++++ 2 files changed, 170 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-icnova-swac.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..e8f44c705089 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -638,6 +638,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-cubietruck.dtb \ sun7i-a20-hummingbird.dtb \ sun7i-a20-i12-tvbox.dtb \ + sun7i-a20-icnova-swac.dtb \ sun7i-a20-m3.dtb \ sun7i-a20-mk808c.dtb \ sun7i-a20-olimex-som-evb.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts b/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts new file mode 100644 index 000000000000..f5b5325a70e2 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts @@ -0,0 +1,169 @@ +/* + * Copyright 2015 Stefan Roese + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun7i-a20.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include +#include + +/ { + model = "ICnova-A20 SWAC"; + compatible = "swac,icnova-a20-swac", "incircuit,icnova-a20", "allwinner,sun7i-a20"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 8 5 GPIO_ACTIVE_HIGH>; /* PI5 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; -- cgit v1.2.3 From 5058ec4a95d1822156cc6ec5d93f4cc0c999c641 Mon Sep 17 00:00:00 2001 From: Lawrence Yu Date: Sun, 25 Oct 2015 13:49:32 -0700 Subject: dts: sun6i: yones toptech bs1078 v2: Add AXP221 support to dts Enable the axp221 PMIC chip in the dts file. Allows board to power off correctly from the poweroff command This board requires dc1sw to be enabled in order to provide a power source for the 5V DCDC converter that powers USB2. This board uses dldo1 for 3.3V wifi power This board requires dldo3 to be enabled at 2.8V in order to provide voltage to the pullup resistors for the i2c0 bus. Signed-off-by: Lawrence Yu Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- .../dts/sun6i-a31s-yones-toptech-bs1078-v2.dts | 85 ++++++++++++++++++++-- 1 file changed, 78 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts index b199020733d3..360adfb1e9ca 100644 --- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts @@ -113,18 +113,83 @@ allwinner,pull = ; }; -®_usb1_vbus { - gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>; +&p2wi { status = "okay"; + + axp22x: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; }; -&usb1_vbus_pin_a { - allwinner,pins = "PH27"; +#include "axp22x.dtsi" + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; }; -&usbphy { - usb1_vbus-supply = <®_usb1_vbus>; - status = "okay"; +®_dc1sw { + regulator-name = "vcc-lcd-usb2"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +®_dc5ldo { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpus"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc4 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-sys-dll"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +/* Voltage source for I2C pullup resistors for I2C Bus 0 */ +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vddio-csi"; }; &uart0 { @@ -132,3 +197,9 @@ pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + +&usbphy { + usb1_vbus-supply = <®_dldo1>; + usb2_vbus-supply = <®_dc1sw>; + status = "okay"; +}; -- cgit v1.2.3 From 18f17cb7d79c6cb6d6ed87c5956a0ebf084db44d Mon Sep 17 00:00:00 2001 From: Marcus Weseloh Date: Sat, 31 Oct 2015 13:55:42 +0100 Subject: ARM: dts: sun4i: Enable audio codec on Olimex A20-SOM-EVB Enable the on-chip audio codec on the Olimex A20-SOM-EVB Signed-off-by: Marcus Weseloh Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts index b7fe102475e7..a91879ed07f8 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -86,6 +86,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &gmac { pinctrl-names = "default"; pinctrl-0 = <&gmac_pins_rgmii_a>; -- cgit v1.2.3 From 581de703ef3293fb71925a250fce08218924e7dc Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Sun, 1 Nov 2015 16:53:52 +0300 Subject: ARM: dts: sun7i: Enable audio codec on Wexler TAB7200 tablet. Enable on-chip audio codec on the Wexler TAB7200 tablet. Signed-off-by: Aleksei Mamlin Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 78239ad988e7..239b5d2915a4 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -62,6 +62,10 @@ }; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; -- cgit v1.2.3 From 111af755658e2417b48df978f7a231c3c616fe3e Mon Sep 17 00:00:00 2001 From: Jelle van der Waa Date: Tue, 3 Nov 2015 16:47:20 +0100 Subject: ARM: dts: sun7i: Enable audio codec on pcDuino Enable the on-chip audio codec Signed-off-by: Jelle van der Waa Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-pcduino3.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts index 861a4a66fb19..1a8b39be1d61 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts @@ -111,6 +111,10 @@ allwinner,pins = "PH2"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; -- cgit v1.2.3 From e6c9b75453f48c455c8e2831cb265329a307cb29 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Tue, 3 Nov 2015 16:51:48 +0100 Subject: ARM: dts: sun4i: inet9f-rev03: Add support for game buttons / joysticks The inet9f-rev03 tablet has multiple fire-buttons / direction controls, add support for these using the same axis mapping as ps2 compatible game controllers with the same stick / button layout use. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts | 164 +++++++++++++++++++++++++++ 1 file changed, 164 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts index 2fffc0434075..ca49b0d0ce1e 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts @@ -59,6 +59,159 @@ chosen { stdout-path = "serial0:115200n8"; }; + + gpio_keys { + compatible = "gpio-keys-polled"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_inet9f>; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + button@0 { + label = "Left Joystick Left"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */ + }; + + button@1 { + label = "Left Joystick Right"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */ + }; + + button@2 { + label = "Left Joystick Up"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ + }; + + button@3 { + label = "Left Joystick Down"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ + }; + + button@4 { + label = "Right Joystick Left"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */ + }; + + button@5 { + label = "Right Joystick Right"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */ + }; + + button@6 { + label = "Right Joystick Up"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */ + }; + + button@7 { + label = "Right Joystick Down"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */ + }; + + button@8 { + label = "DPad Left"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */ + }; + + button@9 { + label = "DPad Right"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */ + }; + + button@10 { + label = "DPad Up"; + linux,code = ; + linux,input-type = ; + linux,input-value = <0xffffffff>; /* -1 */ + gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */ + }; + + button@11 { + label = "DPad Down"; + linux,code = ; + linux,input-type = ; + linux,input-value = <1>; + gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */ + }; + + button@12 { + label = "Button X"; + linux,code = ; + gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */ + }; + + button@13 { + label = "Button Y"; + linux,code = ; + gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */ + }; + + button@14 { + label = "Button A"; + linux,code = ; + gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */ + }; + + button@15 { + label = "Button B"; + linux,code = ; + gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */ + }; + + button@16 { + label = "Select Button"; + linux,code = ; + gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */ + }; + + button@17 { + label = "Start Button"; + linux,code = ; + gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */ + }; + + button@18 { + label = "Top Left Button"; + linux,code = ; + gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */ + }; + + button@19 { + label = "Top Right Button"; + linux,code = ; + gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */ + }; + }; }; &cpu0 { @@ -157,6 +310,17 @@ }; &pio { + key_pins_inet9f: key_pins@0 { + allwinner,pins = "PA0", "PA1", "PA3", "PA4", + "PA5", "PA6", "PA8", "PA9", + "PA11", "PA12", "PA13", + "PA14", "PA15", "PA16", "PA17", + "PH22", "PH23", "PH24", "PH25", "PH26"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From bc1e2718696e1488392cb1bacc5379300520cebd Mon Sep 17 00:00:00 2001 From: Priit Laes Date: Fri, 6 Nov 2015 19:54:44 +0200 Subject: ARM: dts: sun4i: gemei-g9: Convert to use axp209 regulator nodes Add regulator nodes for axp209 using the axp209.dtsi include. Signed-off-by: Priit Laes Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-gemei-g9.dts | 35 ++++++++++++++++++++++++++++---- 1 file changed, 31 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 3f0aeb8288cd..6b4c29db3387 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -72,6 +72,10 @@ * Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48 */ +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; }; @@ -86,15 +90,13 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupts = <0>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; +#include "axp209.dtsi" + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_a>; @@ -146,6 +148,31 @@ status = "okay"; }; +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + ®_usb1_vbus { status = "okay"; }; -- cgit v1.2.3 From 108f780a704f66f1b9d80a1b8b42d467ecca3981 Mon Sep 17 00:00:00 2001 From: Priit Laes Date: Fri, 6 Nov 2015 19:54:45 +0200 Subject: ARM: dts: sun4i: gemei-g9: Use reg_ldo2 instead of reg_vcc3v0 ADC seems to be using ldo2 for reference voltage. Signed-off-by: Priit Laes Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-gemei-g9.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 6b4c29db3387..16c1a6783090 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -112,7 +112,7 @@ }; &lradc { - vref-supply = <®_vcc3v0>; + vref-supply = <®_ldo2>; status = "okay"; -- cgit v1.2.3 From fef5218430dc52e3d7494986dfff2ff93a6e409a Mon Sep 17 00:00:00 2001 From: Priit Laes Date: Fri, 6 Nov 2015 19:54:46 +0200 Subject: ARM: dts: sun4i: gemei-g9: Enable sun4i audio codec support Gemei G9 has internal speakers and headphone jack. Audio switching from internal speakers to headphones is automatically handled by extra FT2012Q audio amplifier chip that works out of the box. Signed-off-by: Priit Laes Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-gemei-g9.dts | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 16c1a6783090..1d73a9897b71 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -65,12 +65,15 @@ /* * TODO: * 2x cameras via CSI - * audio + * audio input * AXP battery management * NAND * OTG * Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48 */ +&codec { + status = "okay"; +}; &cpu0 { cpu-supply = <®_dcdc2>; -- cgit v1.2.3 From 25e8930ce85b09e2741f15f01ad2c861eb1b4eab Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 25 Sep 2015 15:51:31 +0200 Subject: ARM: ux500: remove regulator-compatible usage The regulator-compatible property from the regulator DT binding was deprecated and the correct approach is to use the node's name. This patch has no functional changes since the values of the node's name and the regulator-compatible match for all the regulators. Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-dbx5x0.dtsi | 33 --------------------------------- 1 file changed, 33 deletions(-) diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index 50f5e9d09203..341f5b7ed242 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -512,63 +512,51 @@ // DB8500_REGULATOR_VAPE db8500_vape_reg: db8500_vape { - regulator-compatible = "db8500_vape"; regulator-always-on; }; // DB8500_REGULATOR_VARM db8500_varm_reg: db8500_varm { - regulator-compatible = "db8500_varm"; }; // DB8500_REGULATOR_VMODEM db8500_vmodem_reg: db8500_vmodem { - regulator-compatible = "db8500_vmodem"; }; // DB8500_REGULATOR_VPLL db8500_vpll_reg: db8500_vpll { - regulator-compatible = "db8500_vpll"; }; // DB8500_REGULATOR_VSMPS1 db8500_vsmps1_reg: db8500_vsmps1 { - regulator-compatible = "db8500_vsmps1"; }; // DB8500_REGULATOR_VSMPS2 db8500_vsmps2_reg: db8500_vsmps2 { - regulator-compatible = "db8500_vsmps2"; }; // DB8500_REGULATOR_VSMPS3 db8500_vsmps3_reg: db8500_vsmps3 { - regulator-compatible = "db8500_vsmps3"; }; // DB8500_REGULATOR_VRF1 db8500_vrf1_reg: db8500_vrf1 { - regulator-compatible = "db8500_vrf1"; }; // DB8500_REGULATOR_SWITCH_SVAMMDSP db8500_sva_mmdsp_reg: db8500_sva_mmdsp { - regulator-compatible = "db8500_sva_mmdsp"; }; // DB8500_REGULATOR_SWITCH_SVAMMDSPRET db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret { - regulator-compatible = "db8500_sva_mmdsp_ret"; }; // DB8500_REGULATOR_SWITCH_SVAPIPE db8500_sva_pipe_reg: db8500_sva_pipe { - regulator-compatible = "db8500_sva_pipe"; }; // DB8500_REGULATOR_SWITCH_SIAMMDSP db8500_sia_mmdsp_reg: db8500_sia_mmdsp { - regulator-compatible = "db8500_sia_mmdsp"; }; // DB8500_REGULATOR_SWITCH_SIAMMDSPRET @@ -577,39 +565,32 @@ // DB8500_REGULATOR_SWITCH_SIAPIPE db8500_sia_pipe_reg: db8500_sia_pipe { - regulator-compatible = "db8500_sia_pipe"; }; // DB8500_REGULATOR_SWITCH_SGA db8500_sga_reg: db8500_sga { - regulator-compatible = "db8500_sga"; vin-supply = <&db8500_vape_reg>; }; // DB8500_REGULATOR_SWITCH_B2R2_MCDE db8500_b2r2_mcde_reg: db8500_b2r2_mcde { - regulator-compatible = "db8500_b2r2_mcde"; vin-supply = <&db8500_vape_reg>; }; // DB8500_REGULATOR_SWITCH_ESRAM12 db8500_esram12_reg: db8500_esram12 { - regulator-compatible = "db8500_esram12"; }; // DB8500_REGULATOR_SWITCH_ESRAM12RET db8500_esram12_ret_reg: db8500_esram12_ret { - regulator-compatible = "db8500_esram12_ret"; }; // DB8500_REGULATOR_SWITCH_ESRAM34 db8500_esram34_reg: db8500_esram34 { - regulator-compatible = "db8500_esram34"; }; // DB8500_REGULATOR_SWITCH_ESRAM34RET db8500_esram34_ret_reg: db8500_esram34_ret { - regulator-compatible = "db8500_esram34_ret"; }; }; @@ -721,7 +702,6 @@ compatible = "stericsson,ab8500-ext-regulator"; ab8500_ext1_reg: ab8500_ext1 { - regulator-compatible = "ab8500_ext1"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -729,7 +709,6 @@ }; ab8500_ext2_reg: ab8500_ext2 { - regulator-compatible = "ab8500_ext2"; regulator-min-microvolt = <1360000>; regulator-max-microvolt = <1360000>; regulator-boot-on; @@ -737,7 +716,6 @@ }; ab8500_ext3_reg: ab8500_ext3 { - regulator-compatible = "ab8500_ext3"; regulator-min-microvolt = <3400000>; regulator-max-microvolt = <3400000>; regulator-boot-on; @@ -750,7 +728,6 @@ // supplies to the display/camera ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { - regulator-compatible = "ab8500_ldo_aux1"; regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2900000>; regulator-boot-on; @@ -760,56 +737,46 @@ // supplies to the on-board eMMC ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { - regulator-compatible = "ab8500_ldo_aux2"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <3300000>; }; // supply for VAUX3; SDcard slots ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { - regulator-compatible = "ab8500_ldo_aux3"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <3300000>; }; // supply for v-intcore12; VINTCORE12 LDO ab8500_ldo_intcore_reg: ab8500_ldo_intcore { - regulator-compatible = "ab8500_ldo_intcore"; }; // supply for tvout; gpadc; TVOUT LDO ab8500_ldo_tvout_reg: ab8500_ldo_tvout { - regulator-compatible = "ab8500_ldo_tvout"; }; // supply for ab8500-usb; USB LDO ab8500_ldo_usb_reg: ab8500_ldo_usb { - regulator-compatible = "ab8500_ldo_usb"; }; // supply for ab8500-vaudio; VAUDIO LDO ab8500_ldo_audio_reg: ab8500_ldo_audio { - regulator-compatible = "ab8500_ldo_audio"; }; // supply for v-anamic1 VAMIC1 LDO ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { - regulator-compatible = "ab8500_ldo_anamic1"; }; // supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { - regulator-compatible = "ab8500_ldo_anamic2"; }; // supply for v-dmic; VDMIC LDO ab8500_ldo_dmic_reg: ab8500_ldo_dmic { - regulator-compatible = "ab8500_ldo_dmic"; }; // supply for U8500 CSI/DSI; VANA LDO ab8500_ldo_ana_reg: ab8500_ldo_ana { - regulator-compatible = "ab8500_ldo_ana"; }; }; }; -- cgit v1.2.3 From 125fd67753e67a6043e821e397661f0f3aa4d438 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 25 Sep 2015 15:51:32 +0200 Subject: ARM: u300: remove regulator-compatible usage The regulator-compatible property from the regulator DT binding was deprecated and the correct approach is to use the node's name. This patch has no functional changes since the values of the node's name and the regulator-compatible match for all the regulators. Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-u300.dts | 10 ---------- 1 file changed, 10 deletions(-) diff --git a/arch/arm/boot/dts/ste-u300.dts b/arch/arm/boot/dts/ste-u300.dts index 82a661677e97..9c73ac2842ad 100644 --- a/arch/arm/boot/dts/ste-u300.dts +++ b/arch/arm/boot/dts/ste-u300.dts @@ -315,21 +315,17 @@ ab3100-regulators { compatible = "stericsson,ab3100-regulators"; ab3100_ldo_a_reg: ab3100_ldo_a { - regulator-compatible = "ab3100_ldo_a"; startup-delay-us = <200>; regulator-always-on; regulator-boot-on; }; ab3100_ldo_c_reg: ab3100_ldo_c { - regulator-compatible = "ab3100_ldo_c"; startup-delay-us = <200>; }; ab3100_ldo_d_reg: ab3100_ldo_d { - regulator-compatible = "ab3100_ldo_d"; startup-delay-us = <200>; }; ab3100_ldo_e_reg: ab3100_ldo_e { - regulator-compatible = "ab3100_ldo_e"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; startup-delay-us = <200>; @@ -337,7 +333,6 @@ regulator-boot-on; }; ab3100_ldo_f_reg: ab3100_ldo_f { - regulator-compatible = "ab3100_ldo_f"; regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; startup-delay-us = <600>; @@ -345,28 +340,23 @@ regulator-boot-on; }; ab3100_ldo_g_reg: ab3100_ldo_g { - regulator-compatible = "ab3100_ldo_g"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <2850000>; startup-delay-us = <400>; }; ab3100_ldo_h_reg: ab3100_ldo_h { - regulator-compatible = "ab3100_ldo_h"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <2750000>; startup-delay-us = <200>; }; ab3100_ldo_k_reg: ab3100_ldo_k { - regulator-compatible = "ab3100_ldo_k"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2750000>; startup-delay-us = <200>; }; ab3100_ext_reg: ab3100_ext { - regulator-compatible = "ab3100_ext"; }; ab3100_buck_reg: ab3100_buck { - regulator-compatible = "ab3100_buck"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1800000>; startup-delay-us = <1000>; -- cgit v1.2.3 From 9859cd3b1582cbe39f969a500d8b7fc87c4b87b8 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Mon, 16 Nov 2015 17:57:11 +0900 Subject: ARM: shmobile: r8a7794: Add DU0 clock The DU0 clock is an MSTP clock, child of the CPG ZX clock. Signed-off-by: Laurent Pinchart Acked-by: Geert Uytterhoeven Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 7 ++++--- include/dt-bindings/clock/r8a7794-clock.h | 1 + 2 files changed, 5 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 018ff56470b6..b70e4061d8b1 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -1017,19 +1017,20 @@ reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>; clocks = <&mp_clk>, <&mp_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zs_clk>, - <&zs_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>; + <&zs_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, + <&zx_clk>; #clock-cells = <1>; clock-indices = < R8A7794_CLK_EHCI R8A7794_CLK_HSUSB R8A7794_CLK_HSCIF2 R8A7794_CLK_SCIF5 R8A7794_CLK_SCIF4 R8A7794_CLK_HSCIF1 R8A7794_CLK_HSCIF0 R8A7794_CLK_SCIF3 R8A7794_CLK_SCIF2 R8A7794_CLK_SCIF1 - R8A7794_CLK_SCIF0 + R8A7794_CLK_SCIF0 R8A7794_CLK_DU0 >; clock-output-names = "ehci", "hsusb", "hscif2", "scif5", "scif4", "hscif1", "hscif0", - "scif3", "scif2", "scif1", "scif0"; + "scif3", "scif2", "scif1", "scif0", "du0"; }; mstp8_clks: mstp8_clks@e6150990 { compatible = "renesas,r8a7794-mstp-clocks", "renesas,cpg-mstp-clocks"; diff --git a/include/dt-bindings/clock/r8a7794-clock.h b/include/dt-bindings/clock/r8a7794-clock.h index 09da38a58776..a7a7e0370968 100644 --- a/include/dt-bindings/clock/r8a7794-clock.h +++ b/include/dt-bindings/clock/r8a7794-clock.h @@ -79,6 +79,7 @@ #define R8A7794_CLK_SCIF2 19 #define R8A7794_CLK_SCIF1 20 #define R8A7794_CLK_SCIF0 21 +#define R8A7794_CLK_DU0 24 /* MSTP8 */ #define R8A7794_CLK_VIN1 10 -- cgit v1.2.3 From 46c4f13d04d729fa79f7df2dd1978f9fc0ee6d6a Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Mon, 16 Nov 2015 17:57:20 +0900 Subject: ARM: shmobile: r8a7794: Add DU node to device tree Add the DU device with a disabled state. Boards that want to enable the DU need to specify the output topology. Signed-off-by: Laurent Pinchart Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index b70e4061d8b1..4075a0a3d5c1 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -750,6 +750,34 @@ }; }; + du: display@feb00000 { + compatible = "renesas,du-r8a7794"; + reg = <0 0xfeb00000 0 0x40000>; + reg-names = "du"; + interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, + <0 268 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7794_CLK_DU0>, + <&mstp7_clks R8A7794_CLK_DU0>; + clock-names = "du.0", "du.1"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb0: endpoint { + }; + }; + port@1 { + reg = <1>; + du_out_rgb1: endpoint { + }; + }; + }; + }; + clocks { #address-cells = <2>; #size-cells = <2>; -- cgit v1.2.3 From 876e7fb9f418fd86719af345febf8656c47e833c Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 16 Nov 2015 17:57:29 +0900 Subject: ARM: shmobile: r8a7794: alt: Enable VGA port Enable the DU device and the VGA port available on the r8a7794 ALT board. The VGA portion of the ALT board is somewhat similar to the Lager board but in case of ALT the DU1 pins are used and the X2 clock has a reduced frequency. This patch does not include any pinctrl (PFC) settings due to lack of PFC DT integration on r8a7794. At this point the default state of the boot loader is enough to keep the VGA port working without changing any pinctrl settings. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 61 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 928cfa641475..a548007b9b10 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -33,6 +33,67 @@ #address-cells = <1>; #size-cells = <1>; }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb1>; + }; + }; + port@1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + x2_clk: x2-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <74250000>; + }; + + x13_clk: x13-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; +}; + +&du { + status = "okay"; + + clocks = <&mstp7_clks R8A7794_CLK_DU0>, + <&mstp7_clks R8A7794_CLK_DU0>, + <&x13_clk>, <&x2_clk>; + clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1"; + + ports { + port@1 { + endpoint { + remote-endpoint = <&adv7123_in>; + }; + }; + }; }; &extal_clk { -- cgit v1.2.3 From d96011d07728f7d66edf634407d2919e7708c5c3 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 16 Nov 2015 22:49:12 +0900 Subject: ARM: shmobile: r8a7793: Add GPIO nodes to device tree Add r8a7793 GPIO device nodes that are assumed to be identical to r8a7791. This matches the data sheet for GPIO and MSTP bits. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 121 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 118 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index aa9b64c14a09..36b6d4e67f34 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -57,6 +57,110 @@ interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; }; + gpio0: gpio@e6050000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6050000 0 0x50>; + interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO0>; + power-domains = <&cpg_clocks>; + }; + + gpio1: gpio@e6051000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6051000 0 0x50>; + interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 32 26>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO1>; + power-domains = <&cpg_clocks>; + }; + + gpio2: gpio@e6052000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6052000 0 0x50>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 64 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO2>; + power-domains = <&cpg_clocks>; + }; + + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6053000 0 0x50>; + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO3>; + power-domains = <&cpg_clocks>; + }; + + gpio4: gpio@e6054000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6054000 0 0x50>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 128 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO4>; + power-domains = <&cpg_clocks>; + }; + + gpio5: gpio@e6055000 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6055000 0 0x50>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 160 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO5>; + power-domains = <&cpg_clocks>; + }; + + gpio6: gpio@e6055400 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6055400 0 0x50>; + interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO6>; + power-domains = <&cpg_clocks>; + }; + + gpio7: gpio@e6055800 { + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar"; + reg = <0 0xe6055800 0 0x50>; + interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 224 26>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7793_CLK_GPIO7>; + power-domains = <&cpg_clocks>; + }; + thermal@e61f0000 { compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal"; reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; @@ -484,10 +588,21 @@ mstp9_clks: mstp9_clks@e6150994 { compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150994 0 4>, <0 0xe61509a4 0 4>; - clocks = <&cpg_clocks R8A7793_CLK_QSPI>; + clocks = <&cp_clk>, <&cp_clk>, <&cp_clk>, <&cp_clk>, + <&cp_clk>, <&cp_clk>, <&cp_clk>, <&cp_clk>, + <&cpg_clocks R8A7793_CLK_QSPI>; #clock-cells = <1>; - clock-indices = ; - clock-output-names = "qspi_mod"; + clock-indices = < + R8A7793_CLK_GPIO7 R8A7793_CLK_GPIO6 + R8A7793_CLK_GPIO5 R8A7793_CLK_GPIO4 + R8A7793_CLK_GPIO3 R8A7793_CLK_GPIO2 + R8A7793_CLK_GPIO1 R8A7793_CLK_GPIO0 + R8A7793_CLK_QSPI_MOD + >; + clock-output-names = + "gpio7", "gpio6", "gpio5", "gpio4", + "gpio3", "gpio2", "gpio1", "gpio0", + "qspi_mod"; }; }; -- cgit v1.2.3 From 4af0a6640cb536cd66ecff1bb7827c76d2475bd9 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 13 Nov 2015 11:23:48 +0900 Subject: ARM: shmobile: r8a7790: Use SoC specific binding for rcar-dmac nodes Use the new SoC specific binding for rcar-dmac and the generic binding as a fall-back in the r8a7790 device tree. In general Renesas hardware is not documented to the extent where the relationship between IP blocks on different SoCs can be assumed although they may appear to operate the same way. Furthermore the documentation typically does not specify a version for individual IP blocks. For these reasons a convention of using the SoC name in place of a version and providing SoC-specific compat strings has been adopted. Although not universally liked this convention is used in the bindings for most drivers for Renesas hardware. The purpose of this patch is to update the Renesas R-Car DMA Controller nodes to follow this convention. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index b545fef3f7db..105bf9ae18cb 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -266,7 +266,7 @@ }; dmac0: dma-controller@e6700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xe6700000 0 0x20000>; interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH 0 200 IRQ_TYPE_LEVEL_HIGH @@ -297,7 +297,7 @@ }; dmac1: dma-controller@e6720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xe6720000 0 0x20000>; interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH 0 216 IRQ_TYPE_LEVEL_HIGH @@ -328,7 +328,7 @@ }; audma0: dma-controller@ec700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xec700000 0 0x10000>; interrupts = <0 346 IRQ_TYPE_LEVEL_HIGH 0 320 IRQ_TYPE_LEVEL_HIGH @@ -357,7 +357,7 @@ }; audma1: dma-controller@ec720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xec720000 0 0x10000>; interrupts = <0 347 IRQ_TYPE_LEVEL_HIGH 0 333 IRQ_TYPE_LEVEL_HIGH -- cgit v1.2.3 From e6d12b4990e79ecb0d39736df5d1877ad69fab4c Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 13 Nov 2015 11:23:49 +0900 Subject: ARM: shmobile: r8a7791: Use SoC specific binding for rcar-dmac nodes Use the new SoC specific binding for rcar-dmac and the generic binding as a fall-back in the r8a7791 device tree. In general Renesas hardware is not documented to the extent where the relationship between IP blocks on different SoCs can be assumed although they may appear to operate the same way. Furthermore the documentation typically does not specify a version for individual IP blocks. For these reasons a convention of using the SoC name in place of a version and providing SoC-specific compat strings has been adopted. Although not universally liked this convention is used in the bindings for most drivers for Renesas hardware. The purpose of this patch is to update the Renesas R-Car DMA Controller nodes to follow this convention. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 2bc54e359768..9f5f30e714c5 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -255,7 +255,7 @@ }; dmac0: dma-controller@e6700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7791", "renesas,rcar-dmac"; reg = <0 0xe6700000 0 0x20000>; interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH 0 200 IRQ_TYPE_LEVEL_HIGH @@ -286,7 +286,7 @@ }; dmac1: dma-controller@e6720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7791", "renesas,rcar-dmac"; reg = <0 0xe6720000 0 0x20000>; interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH 0 216 IRQ_TYPE_LEVEL_HIGH @@ -317,7 +317,7 @@ }; audma0: dma-controller@ec700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7791", "renesas,rcar-dmac"; reg = <0 0xec700000 0 0x10000>; interrupts = <0 346 IRQ_TYPE_LEVEL_HIGH 0 320 IRQ_TYPE_LEVEL_HIGH @@ -346,7 +346,7 @@ }; audma1: dma-controller@ec720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7791", "renesas,rcar-dmac"; reg = <0 0xec720000 0 0x10000>; interrupts = <0 347 IRQ_TYPE_LEVEL_HIGH 0 333 IRQ_TYPE_LEVEL_HIGH -- cgit v1.2.3 From 061c6c624b2f356a0d02b137ae4f46825ddd44d1 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 13 Nov 2015 11:23:50 +0900 Subject: ARM: shmobile: r8a7793: Use SoC specific binding for rcar-dmac nodes Use the new SoC specific binding for rcar-dmac and the generic binding as a fall-back in the r8a7793 device tree. In general Renesas hardware is not documented to the extent where the relationship between IP blocks on different SoCs can be assumed although they may appear to operate the same way. Furthermore the documentation typically does not specify a version for individual IP blocks. For these reasons a convention of using the SoC name in place of a version and providing SoC-specific compat strings has been adopted. Although not universally liked this convention is used in the bindings for most drivers for Renesas hardware. The purpose of this patch is to update the Renesas R-Car DMA Controller nodes to follow this convention. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 36b6d4e67f34..2378df52aa32 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -237,7 +237,7 @@ }; dmac0: dma-controller@e6700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7793", "renesas,rcar-dmac"; reg = <0 0xe6700000 0 0x20000>; interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH 0 200 IRQ_TYPE_LEVEL_HIGH @@ -268,7 +268,7 @@ }; dmac1: dma-controller@e6720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7793", "renesas,rcar-dmac"; reg = <0 0xe6720000 0 0x20000>; interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH 0 216 IRQ_TYPE_LEVEL_HIGH -- cgit v1.2.3 From 0a3d058b8ae857d270a0d34081554192f3e2e566 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 13 Nov 2015 11:23:51 +0900 Subject: ARM: shmobile: r8a7794: Use SoC specific binding for rcar-dmac nodes Use the new SoC specific binding for rcar-dmac and the generic binding as a fall-back in the r8a7794 device tree. In general Renesas hardware is not documented to the extent where the relationship between IP blocks on different SoCs can be assumed although they may appear to operate the same way. Furthermore the documentation typically does not specify a version for individual IP blocks. For these reasons a convention of using the SoC name in place of a version and providing SoC-specific compat strings has been adopted. Although not universally liked this convention is used in the bindings for most drivers for Renesas hardware. The purpose of this patch is to update the Renesas R-Car DMA Controller nodes to follow this convention. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 4075a0a3d5c1..57d188c2bf6d 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -221,7 +221,7 @@ }; dmac0: dma-controller@e6700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7794", "renesas,rcar-dmac"; reg = <0 0xe6700000 0 0x20000>; interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH 0 200 IRQ_TYPE_LEVEL_HIGH @@ -252,7 +252,7 @@ }; dmac1: dma-controller@e6720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7794", "renesas,rcar-dmac"; reg = <0 0xe6720000 0 0x20000>; interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH 0 216 IRQ_TYPE_LEVEL_HIGH -- cgit v1.2.3 From 94af7a3c310f5877dc6f756179b92f24f89a9b08 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 19 Oct 2015 14:00:32 +0900 Subject: clk: samsung: exynos4: Add SSS gate clock Add a gate clock for controlling all clocks of Security Sub System (SSS). Signed-off-by: Krzysztof Kozlowski Acked-by: Stephen Boyd --- drivers/clk/samsung/clk-exynos4.c | 1 + include/dt-bindings/clock/exynos4.h | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/clk/samsung/clk-exynos4.c b/drivers/clk/samsung/clk-exynos4.c index 7f370d3e0983..ac03e4fe2871 100644 --- a/drivers/clk/samsung/clk-exynos4.c +++ b/drivers/clk/samsung/clk-exynos4.c @@ -1024,6 +1024,7 @@ static struct samsung_gate_clock exynos4_gate_clks[] __initdata = { 0, 0), GATE(CLK_AC97, "ac97", "aclk100", GATE_IP_PERIL, 27, 0, 0), + GATE(CLK_SSS, "sss", "aclk133", GATE_IP_DMC, 4, 0, 0), GATE(CLK_PPMUDMC0, "ppmudmc0", "aclk133", GATE_IP_DMC, 8, 0, 0), GATE(CLK_PPMUDMC1, "ppmudmc1", "aclk133", GATE_IP_DMC, 9, 0, 0), GATE(CLK_PPMUCPU, "ppmucpu", "aclk133", GATE_IP_DMC, 10, 0, 0), diff --git a/include/dt-bindings/clock/exynos4.h b/include/dt-bindings/clock/exynos4.h index c4b1676ea674..c40111f36d5e 100644 --- a/include/dt-bindings/clock/exynos4.h +++ b/include/dt-bindings/clock/exynos4.h @@ -93,6 +93,7 @@ #define CLK_SCLK_FIMG2D 177 /* gate clocks */ +#define CLK_SSS 255 #define CLK_FIMC0 256 #define CLK_FIMC1 257 #define CLK_FIMC2 258 -- cgit v1.2.3 From 1a24edd2ee4656610829fdda69e53fdc6fa4ee99 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:50 +0300 Subject: arm: dts: lpc32xx: change include syntax to be C preprocessor friendly The change replaces /include/ to #include in lpc32xx.dtsi and derivatives, it is required, if C preprocessor is intended to be used over dtsi/dts files, otherwise errors like one below are generated: Error: ea3250.dts:15.1-9 syntax error FATAL ERROR: Unable to parse input tree Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/ea3250.dts | 2 +- arch/arm/boot/dts/lpc32xx.dtsi | 2 +- arch/arm/boot/dts/phy3250.dts | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/ea3250.dts b/arch/arm/boot/dts/ea3250.dts index a4ba31b23c88..121d0328a0d6 100644 --- a/arch/arm/boot/dts/ea3250.dts +++ b/arch/arm/boot/dts/ea3250.dts @@ -12,7 +12,7 @@ */ /dts-v1/; -/include/ "lpc32xx.dtsi" +#include "lpc32xx.dtsi" / { model = "Embedded Artists LPC3250 board based on NXP LPC3250"; diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index 3abebb75fc57..f35e9822ddec 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -11,7 +11,7 @@ * http://www.gnu.org/copyleft/gpl.html */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { compatible = "nxp,lpc3220"; diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts index 90fdbd77f274..2a2d2cfd02c8 100644 --- a/arch/arm/boot/dts/phy3250.dts +++ b/arch/arm/boot/dts/phy3250.dts @@ -12,7 +12,7 @@ */ /dts-v1/; -/include/ "lpc32xx.dtsi" +#include "lpc32xx.dtsi" / { model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; -- cgit v1.2.3 From 25de7c961588f10df3d5c8d5b54d70fe39b7d256 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:51 +0300 Subject: arm: dts: lpc32xx: add labels to all defined peripheral nodes To simplify writing of dts files for all lpc32xx.dtsi users who adjust device node properties, add labels to all defined peripheral device nodes in lpc32xx.dtsi. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/lpc32xx.dtsi | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index f35e9822ddec..00570b308b23 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -49,7 +49,7 @@ status = "disabled"; }; - dma@31000000 { + dma: dma@31000000 { compatible = "arm,pl080", "arm,primecell"; reg = <0x31000000 0x1000>; interrupts = <0x1c 0>; @@ -58,21 +58,21 @@ /* * Enable either ohci or usbd (gadget)! */ - ohci@31020000 { + ohci: ohci@31020000 { compatible = "nxp,ohci-nxp", "usb-ohci"; reg = <0x31020000 0x300>; interrupts = <0x3b 0>; status = "disabled"; }; - usbd@31020000 { + usbd: usbd@31020000 { compatible = "nxp,lpc3220-udc"; reg = <0x31020000 0x300>; interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; status = "disabled"; }; - clcd@31040000 { + clcd: clcd@31040000 { compatible = "arm,pl110", "arm,primecell"; reg = <0x31040000 0x1000>; interrupts = <0x0e 0>; @@ -118,7 +118,7 @@ reg = <0x20094000 0x1000>; }; - sd@20098000 { + sd: sd@20098000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x20098000 0x1000>; interrupts = <0x0f 0>, <0x0d 0>; @@ -243,7 +243,7 @@ status = "disabled"; }; - rtc@40024000 { + rtc: rtc@40024000 { compatible = "nxp,lpc3220-rtc"; reg = <0x40024000 0x1000>; interrupts = <0x34 0>; @@ -256,7 +256,7 @@ #gpio-cells = <3>; /* bank, pin, flags */ }; - watchdog@4003C000 { + watchdog: watchdog@4003C000 { compatible = "nxp,pnx4008-wdt"; reg = <0x4003C000 0x1000>; }; @@ -268,21 +268,21 @@ * them */ - adc@40048000 { + adc: adc@40048000 { compatible = "nxp,lpc3220-adc"; reg = <0x40048000 0x1000>; interrupts = <0x27 0>; status = "disabled"; }; - tsc@40048000 { + tsc: tsc@40048000 { compatible = "nxp,lpc3220-tsc"; reg = <0x40048000 0x1000>; interrupts = <0x27 0>; status = "disabled"; }; - key@40050000 { + key: key@40050000 { compatible = "nxp,lpc3220-key"; reg = <0x40050000 0x1000>; interrupts = <54 0>; -- cgit v1.2.3 From 246d8fc33e570b7c1e69cdbf395fcfcee58785cc Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:52 +0300 Subject: arm: dts: lpc32xx: add reg property to cpu device node According to device tree bindings for ARM cpus cpu node must contain a reg property for enumeration scheme. The change adds reg = <0x0> indicating that the processor does not have CPU identification register and updates cell settings. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/lpc32xx.dtsi | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index 00570b308b23..fb0e9ae8238f 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -18,12 +18,13 @@ interrupt-parent = <&mic>; cpus { - #address-cells = <0>; + #address-cells = <1>; #size-cells = <0>; - cpu { + cpu@0 { compatible = "arm,arm926ej-s"; device_type = "cpu"; + reg = <0x0>; }; }; -- cgit v1.2.3 From 2a6c6563313dd5c96277e4a3368df65e268bcc9b Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:53 +0300 Subject: arm: dts: lpc32xx: add device node for the second pwm controller LPC32xx SoCs have two independent PWM controllers, they have different clock parents, clock gates and even slightly different controls, each of these two PWM controllers has one output channel. Due to almost similar controls arranged in a row it is incorrectly assumed that there is one PWM controller with two channels, fix this problem in lpc32xx.dtsi, which at the moment prevents separate configuration of different clock parents and gates for both PWM controllers. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/lpc32xx.dtsi | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index fb0e9ae8238f..be829926f860 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -290,9 +290,15 @@ status = "disabled"; }; - pwm: pwm@4005C000 { + pwm1: pwm@4005C000 { compatible = "nxp,lpc3220-pwm"; - reg = <0x4005C000 0x8>; + reg = <0x4005C000 0x4>; + status = "disabled"; + }; + + pwm2: pwm@4005C004 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005C004 0x4>; status = "disabled"; }; }; -- cgit v1.2.3 From cae59490674cf8dab153c6b1350247228b3fc972 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:54 +0300 Subject: arm: dts: ea3250/phy3250: specify phys memory offset for lpc32xx boards In case if SDRAM memory region is not populated by a bootloader, provide this value in device trees for EA3250 and PHY3250 boards. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/ea3250.dts | 2 +- arch/arm/boot/dts/phy3250.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/ea3250.dts b/arch/arm/boot/dts/ea3250.dts index 121d0328a0d6..392430b25154 100644 --- a/arch/arm/boot/dts/ea3250.dts +++ b/arch/arm/boot/dts/ea3250.dts @@ -22,7 +22,7 @@ memory { device_type = "memory"; - reg = <0 0x4000000>; + reg = <0x80000000 0x4000000>; }; ahb { diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts index 2a2d2cfd02c8..79a20f7730f3 100644 --- a/arch/arm/boot/dts/phy3250.dts +++ b/arch/arm/boot/dts/phy3250.dts @@ -22,7 +22,7 @@ memory { device_type = "memory"; - reg = <0 0x4000000>; + reg = <0x80000000 0x4000000>; }; ahb { -- cgit v1.2.3 From f83ee67fcf8d743e7fbcb08c70fcd32c253bb2fa Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:55 +0300 Subject: arm: dts: lpc32xx: add external memory controller device node The change adds a description of ARM PrimeCell PL175 memory controller, which is found on NXP LPC32xx SoCs. The controller supports up to 4 static memory devices mapped to 0xE000 0000 - 0xE3FF FFFF physical memory area. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/lpc32xx.dtsi | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index be829926f860..a595a4b772d4 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -32,7 +32,8 @@ #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; - ranges = <0x20000000 0x20000000 0x30000000>; + ranges = <0x20000000 0x20000000 0x30000000>, + <0xe0000000 0xe0000000 0x04000000>; /* * Enable either SLC or MLC @@ -86,6 +87,19 @@ interrupts = <0x1d 0>; }; + emc: memory-controller@31080000 { + compatible = "arm,pl175", "arm,primecell"; + reg = <0x31080000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0 0xe0000000 0x01000000>, + <1 0xe1000000 0x01000000>, + <2 0xe2000000 0x01000000>, + <3 0xe3000000 0x01000000>; + status = "disabled"; + }; + apb { #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From c1aa70072cfb95d28bd5b63848f9b37e57273f18 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:41:06 +0300 Subject: arm: dts: lpc32xx: add device nodes for standard timers NXP LPC32xx SoCs have 6 standard timers, add device nodes to describe them. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/lpc32xx.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index a595a4b772d4..ba91b203c8c1 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -271,11 +271,31 @@ #gpio-cells = <3>; /* bank, pin, flags */ }; + timer4: timer@4002C000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x4002C000 0x1000>; + interrupts = <0x3 0>; + status = "disabled"; + }; + + timer5: timer@40030000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x40030000 0x1000>; + interrupts = <0x4 0>; + status = "disabled"; + }; + watchdog: watchdog@4003C000 { compatible = "nxp,pnx4008-wdt"; reg = <0x4003C000 0x1000>; }; + timer0: timer@40044000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x40044000 0x1000>; + interrupts = <0x10 0>; + }; + /* * TSC vs. ADC: Since those two share the same * hardware, you need to choose from one of the @@ -297,6 +317,12 @@ status = "disabled"; }; + timer1: timer@4004C000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x4004C000 0x1000>; + interrupts = <0x11 0>; + }; + key: key@40050000 { compatible = "nxp,lpc3220-key"; reg = <0x40050000 0x1000>; @@ -304,6 +330,13 @@ status = "disabled"; }; + timer2: timer@40058000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x40058000 0x1000>; + interrupts = <0x12 0>; + status = "disabled"; + }; + pwm1: pwm@4005C000 { compatible = "nxp,lpc3220-pwm"; reg = <0x4005C000 0x4>; @@ -315,6 +348,13 @@ reg = <0x4005C004 0x4>; status = "disabled"; }; + + timer3: timer@40060000 { + compatible = "nxp,lpc3220-timer"; + reg = <0x40060000 0x1000>; + interrupts = <0x13 0>; + status = "disabled"; + }; }; }; }; -- cgit v1.2.3 From aa29efb445f11506daca0db934331f144b38ddc4 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Sun, 18 Oct 2015 00:35:57 +0300 Subject: arm: dts: lpc32xx: move USB controller subdevices into own device node NXP LPC32xx SoC has one USB OTG controller, which is supposed to work with an external phy (default is NXP ISP1301). Practically the USB controller contains 5 subdevices: - host controller 0x3102 0000 -- 0x3102 00FF - OTG controller 0x3102 0100 -- 0x3102 01FF - device controller 0x3102 0200 -- 0x3102 02FF - I2C controller 0x3102 0300 -- 0x3102 03FF - clock controller 0x3102 0F00 -- 0x3102 0FFF The USB controller can be considered as a "bus", because the subdevices above are relatively independent, for example I2C controller is the same as other two general purpose I2C controllers found on SoC. The change is not intended to modify any logic, but it rearranges existing device nodes, in future it is planned to add a USB clock controller device node into the same group. Signed-off-by: Vladimir Zapolskiy --- arch/arm/boot/dts/ea3250.dts | 37 ++++++++++++----------------- arch/arm/boot/dts/lpc32xx.dtsi | 53 ++++++++++++++++++++++++------------------ arch/arm/boot/dts/phy3250.dts | 37 ++++++++++++----------------- 3 files changed, 60 insertions(+), 67 deletions(-) diff --git a/arch/arm/boot/dts/ea3250.dts b/arch/arm/boot/dts/ea3250.dts index 392430b25154..a4a281fe82af 100644 --- a/arch/arm/boot/dts/ea3250.dts +++ b/arch/arm/boot/dts/ea3250.dts @@ -31,19 +31,6 @@ use-iram; }; - /* Here, choose exactly one from: ohci, usbd */ - ohci@31020000 { - transceiver = <&isp1301>; - status = "okay"; - }; - -/* - usbd@31020000 { - transceiver = <&isp1301>; - status = "okay"; - }; -*/ - /* 128MB Flash via SLC NAND controller */ slc: flash@20020000 { status = "okay"; @@ -130,15 +117,6 @@ clock-frequency = <100000>; }; - i2cusb: i2c@31020300 { - clock-frequency = <100000>; - - isp1301: usb-transceiver@2d { - compatible = "nxp,isp1301"; - reg = <0x2d>; - }; - }; - sd@20098000 { wp-gpios = <&pca9532 5 0>; cd-gpios = <&pca9532 4 0>; @@ -279,3 +257,18 @@ }; }; }; + +/* Here, choose exactly one from: ohci, usbd */ +&ohci /* &usbd */ { + transceiver = <&isp1301>; + status = "okay"; +}; + +&i2cusb { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2d { + compatible = "nxp,isp1301"; + reg = <0x2d>; + }; +}; diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index ba91b203c8c1..c85cf979725e 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -57,21 +57,37 @@ interrupts = <0x1c 0>; }; - /* - * Enable either ohci or usbd (gadget)! - */ - ohci: ohci@31020000 { - compatible = "nxp,ohci-nxp", "usb-ohci"; - reg = <0x31020000 0x300>; - interrupts = <0x3b 0>; - status = "disabled"; - }; + usb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x0 0x31020000 0x00001000>; - usbd: usbd@31020000 { - compatible = "nxp,lpc3220-udc"; - reg = <0x31020000 0x300>; - interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; - status = "disabled"; + /* + * Enable either ohci or usbd (gadget)! + */ + ohci: ohci@0 { + compatible = "nxp,ohci-nxp", "usb-ohci"; + reg = <0x0 0x300>; + interrupts = <0x3b 0>; + status = "disabled"; + }; + + usbd: usbd@0 { + compatible = "nxp,lpc3220-udc"; + reg = <0x0 0x300>; + interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; + status = "disabled"; + }; + + i2cusb: i2c@300 { + compatible = "nxp,pnx-i2c"; + reg = <0x300 0x100>; + interrupts = <0x3f 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; }; clcd: clcd@31040000 { @@ -207,15 +223,6 @@ status = "disabled"; #pwm-cells = <2>; }; - - i2cusb: i2c@31020300 { - compatible = "nxp,pnx-i2c"; - reg = <0x31020300 0x100>; - interrupts = <0x3f 0>; - #address-cells = <1>; - #size-cells = <0>; - pnx,timeout = <0x64>; - }; }; fab { diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts index 79a20f7730f3..7d253bb6265a 100644 --- a/arch/arm/boot/dts/phy3250.dts +++ b/arch/arm/boot/dts/phy3250.dts @@ -31,19 +31,6 @@ use-iram; }; - /* Here, choose exactly one from: ohci, usbd */ - ohci@31020000 { - transceiver = <&isp1301>; - status = "okay"; - }; - -/* - usbd@31020000 { - transceiver = <&isp1301>; - status = "okay"; - }; -*/ - clcd@31040000 { status = "okay"; }; @@ -123,15 +110,6 @@ clock-frequency = <100000>; }; - i2cusb: i2c@31020300 { - clock-frequency = <100000>; - - isp1301: usb-transceiver@2c { - compatible = "nxp,isp1301"; - reg = <0x2c>; - }; - }; - ssp0: ssp@20084000 { #address-cells = <1>; #size-cells = <0>; @@ -200,3 +178,18 @@ }; }; }; + +/* Here, choose exactly one from: ohci, usbd */ +&ohci /* &usbd */ { + transceiver = <&isp1301>; + status = "okay"; +}; + +&i2cusb { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; +}; -- cgit v1.2.3 From 22b160713cb6944450dad0abd18d8929f60500dc Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Tue, 17 Nov 2015 11:10:40 -0800 Subject: ARM: shmobile: alt: Add pfc pins to DT PFC is already enabled on the r8a7794. This adds pins for devices already enabled in DT on the r8a7794 based alt board. Based on work by Mitsuhiro Kimura and Hisashi Nakamura. Cc: Mitsuhiro Kimura Cc: Hisashi Nakamura Signed-off-by: Simon Horman Acked-by: Ulrich Hecht --- arch/arm/boot/dts/r8a7794-alt.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index a548007b9b10..e7c94554d847 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -100,6 +100,23 @@ clock-frequency = <20000000>; }; +&pfc { + scif2_pins: serial2 { + renesas,groups = "scif2_data"; + renesas,function = "scif2"; + }; + + ether_pins: ether { + renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; + renesas,function = "eth"; + }; + + ether_b_pins: ether { + renesas,groups = "eth_link_b", "eth_mdio_b", "eth_rmii_b"; + renesas,function = "eth"; + }; +}; + &cmt0 { status = "okay"; }; -- cgit v1.2.3 From 7f81bf72c67fbd225adfc0d5f6df0f674d08d757 Mon Sep 17 00:00:00 2001 From: Ulrich Hecht Date: Wed, 18 Nov 2015 13:51:06 +0100 Subject: ARM: shmobile: alt: add I2C1 DT support Defines the board-dependent part of the I2C1 device. Signed-off-by: Ulrich Hecht Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index e7c94554d847..88ed017495e9 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -115,6 +115,11 @@ renesas,groups = "eth_link_b", "eth_mdio_b", "eth_rmii_b"; renesas,function = "eth"; }; + + i2c1_pins: i2c1 { + renesas,groups = "i2c1"; + renesas,function = "i2c1"; + }; }; &cmt0 { @@ -134,6 +139,14 @@ }; }; +&i2c1 { + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + &scif2 { status = "okay"; }; -- cgit v1.2.3 From d537543b3948bc3bc9dede248fa455493e055457 Mon Sep 17 00:00:00 2001 From: Ulrich Hecht Date: Wed, 18 Nov 2015 13:51:07 +0100 Subject: ARM: shmobile: alt: add VIN0, ADV7180 DT support Adds the device board-dependent part of the VIN0 device and its ADV7180 video decoder on I2C1, and the interconnection between them. Based on silk patch by Sergei Shtylyov. Signed-off-by: Ulrich Hecht Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 34 ++++++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 88ed017495e9..fd1cfcdd65ef 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -120,6 +120,11 @@ renesas,groups = "i2c1"; renesas,function = "i2c1"; }; + + vin0_pins: vin0 { + renesas,groups = "vin0_data8", "vin0_clk"; + renesas,function = "vin0"; + }; }; &cmt0 { @@ -145,6 +150,35 @@ status = "okay"; clock-frequency = <400000>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin0>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin0ep>; + }; + }; + }; +}; + +&vin0 { + status = "okay"; + pinctrl-0 = <&vin0_pins>; + pinctrl-names = "default"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vin0ep: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; }; &scif2 { -- cgit v1.2.3 From 3890ab2bfb4579303cafb27225eb74ca568bd363 Mon Sep 17 00:00:00 2001 From: Pramod Kumar Date: Mon, 19 Oct 2015 11:13:10 +0530 Subject: dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT ASIU gpio controller's pins are muxed with pin-cntroller. Add this mapping through property "gpio-ranges". Signed-off-by: Pramod Kumar Reviewed-by: Ray Jui Reviewed-by: Scott Branden Reviewed-by: Linus Walleij Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-cygnus.dtsi | 53 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 51 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index 2778533502d9..c9f1ac455e9a 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -248,10 +248,59 @@ #gpio-cells = <2>; gpio-controller; - pinmux = <&pinctrl>; - interrupt-controller; interrupts = ; + gpio-ranges = <&pinctrl 0 42 1>, + <&pinctrl 1 44 3>, + <&pinctrl 4 48 1>, + <&pinctrl 5 50 3>, + <&pinctrl 8 126 1>, + <&pinctrl 9 155 1>, + <&pinctrl 10 152 1>, + <&pinctrl 11 154 1>, + <&pinctrl 12 153 1>, + <&pinctrl 13 127 3>, + <&pinctrl 16 140 1>, + <&pinctrl 17 145 7>, + <&pinctrl 24 130 10>, + <&pinctrl 34 141 4>, + <&pinctrl 38 54 1>, + <&pinctrl 39 56 3>, + <&pinctrl 42 60 3>, + <&pinctrl 45 64 3>, + <&pinctrl 48 68 2>, + <&pinctrl 50 84 6>, + <&pinctrl 56 94 6>, + <&pinctrl 62 72 1>, + <&pinctrl 63 70 1>, + <&pinctrl 64 80 1>, + <&pinctrl 65 74 3>, + <&pinctrl 68 78 1>, + <&pinctrl 69 82 1>, + <&pinctrl 70 156 17>, + <&pinctrl 87 104 12>, + <&pinctrl 99 102 2>, + <&pinctrl 101 90 4>, + <&pinctrl 105 116 6>, + <&pinctrl 111 100 2>, + <&pinctrl 113 122 4>, + <&pinctrl 123 11 1>, + <&pinctrl 124 38 4>, + <&pinctrl 128 43 1>, + <&pinctrl 129 47 1>, + <&pinctrl 130 49 1>, + <&pinctrl 131 53 1>, + <&pinctrl 132 55 1>, + <&pinctrl 133 59 1>, + <&pinctrl 134 63 1>, + <&pinctrl 135 67 1>, + <&pinctrl 136 71 1>, + <&pinctrl 137 73 1>, + <&pinctrl 138 77 1>, + <&pinctrl 139 79 1>, + <&pinctrl 140 81 1>, + <&pinctrl 141 83 1>, + <&pinctrl 142 10 1>; }; touchscreen: tsc@180a6000 { -- cgit v1.2.3 From 85ef8d611f4b0216bc4f96487a0408d5c887f6f9 Mon Sep 17 00:00:00 2001 From: Sjoerd Simons Date: Fri, 6 Nov 2015 11:46:37 +0100 Subject: ARM: dts: rockchip: Setup rk3288 ethernet0 alias for u-boot Add an ethernet0 alias for the RK3288 mac interface so that u-boot can find the device-node and fill in the mac address on boards that support a wired network interface. Signed-off-by: Sjoerd Simons Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 6a79c9c526b8..16187c39d035 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -53,6 +53,7 @@ interrupt-parent = <&gic>; aliases { + ethernet0 = &gmac; i2c0 = &i2c0; i2c1 = &i2c1; i2c2 = &i2c2; -- cgit v1.2.3 From b3e4b95366a5fcdc1ce3c3e9ffb5db11e1b11939 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Sat, 7 Nov 2015 22:37:26 +0100 Subject: ARM: dts: rockchip: Setup rk3066/rk3188 ethernet0 alias for u-boot Add an ethernet0 alias for the RK3066/RK3188 mac interface so that u-boot can find the device-node and fill in the mac address on boards that support a wired network interface. Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3xxx.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi index 4497d288a7cb..99eeea70223b 100644 --- a/arch/arm/boot/dts/rk3xxx.dtsi +++ b/arch/arm/boot/dts/rk3xxx.dtsi @@ -49,6 +49,7 @@ interrupt-parent = <&gic>; aliases { + ethernet0 = &emac; i2c0 = &i2c0; i2c1 = &i2c1; i2c2 = &i2c2; -- cgit v1.2.3 From 34a315883f60344f2116dcd445388531d09dc066 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 19 Nov 2015 10:15:05 -0600 Subject: ARM: socfpga: Add support for DENX MCV SoM and MCVEVK baseboard Add support for the DENX MCV SoM and MCVEVK baseboard. The SoM contains eMMC, DRAM, Altera Cyclone V SoC. The baseboard contains CAN ports, UART ports, STMPE811 touchscreen controller, USB OTG port, ethernet port and a lot of IO pins. Signed-off-by: Marek Vasut Reviewed-by: Steffen Trumtrar Cc: Vince Bridgers Cc: Alan Tull Cc: Thor Thayer Cc: Olof Johansson Signed-off-by: Dinh Nguyen --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi | 33 ++++++++++ arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts | 94 +++++++++++++++++++++++++++ 3 files changed, 128 insertions(+) create mode 100644 arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi create mode 100644 arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..17fb11b54b33 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -557,6 +557,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \ dtb-$(CONFIG_ARCH_SOCFPGA) += \ socfpga_arria5_socdk.dtb \ socfpga_arria10_socdk_sdmmc.dtb \ + socfpga_cyclone5_mcvevk.dtb \ socfpga_cyclone5_socdk.dtb \ socfpga_cyclone5_de0_sockit.dtb \ socfpga_cyclone5_sockit.dtb \ diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi new file mode 100644 index 000000000000..f0e03a23a864 --- /dev/null +++ b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi @@ -0,0 +1,33 @@ +/* + * Copyright (C) 2015 Marek Vasut + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "DENX MCV"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + + memory { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1 GiB */ + }; +}; + +&mmc0 { /* On-SoM eMMC */ + bus-width = <8>; +}; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts b/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts new file mode 100644 index 000000000000..09d0deddcbf9 --- /dev/null +++ b/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts @@ -0,0 +1,94 @@ +/* + * Copyright (C) 2015 Marek Vasut + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#include "socfpga_cyclone5_mcv.dtsi" + +/ { + model = "DENX MCV EVK"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + + aliases { + ethernet0 = &gmac0; + stmpe-i2c0 = &stmpe1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&can0 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&gmac0 { + phy-mode = "rgmii"; + status = "okay"; +}; + +&gpio0 { /* GPIO 0 ... 28 */ + status = "okay"; +}; + +&gpio1 { /* GPIO 29 ... 57 */ + status = "okay"; +}; + +&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ + status = "okay"; +}; + +&i2c0 { + status = "okay"; + speed-mode = <0>; + + stmpe1: stmpe811@41 { + compatible = "st,stmpe811"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + id = <0>; + blocks = <0x5>; + irq-gpio = <&portb 28 0x4>; /* GPIO 57, trig. level HI */ + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + reg = <0>; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <3>; + ts,settling = <4>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; -- cgit v1.2.3 From 2523cc91e6c7ca570d8d04db2035f6b2eb2341f2 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 16 Nov 2015 18:43:37 +0800 Subject: arm: dts: berlin2q-marvell-dmp: remove broken-cd from eMMC node The eMMC is non-removable so is marked with the non-removable DT property to avoid having to redetect it after a suspend/resume. But it also has the broken-cd property which is wrong since only one of the DT properties for card detection should be used Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts index da28c9704a9d..cdcf89bfec33 100644 --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts @@ -94,7 +94,6 @@ }; &sdhci2 { - broken-cd; bus-width = <8>; non-removable; status = "okay"; -- cgit v1.2.3 From 5ee90578bbe82e06eae8a83f8676ec0ee95b8224 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 16 Nov 2015 18:46:31 +0800 Subject: arm: dts: berlin2q: remove duplicated interrupt-parent The default interrupt-parent has been set in the upper layer, apb@e80000 and apb@fc0000 for example. So if the interrupt-parent isn't changed, we don't need to set it again. This patch removes the dumplicated interrupt-parent settings. Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2q.dtsi | 6 ------ 1 file changed, 6 deletions(-) diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index 8ea177f375dd..155430a2d747 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -309,7 +309,6 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x1400 0x100>; - interrupt-parent = <&aic>; interrupts = <4>; clocks = <&chip_clk CLKID_CFG>; pinctrl-0 = <&twsi0_pmux>; @@ -322,7 +321,6 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x1800 0x100>; - interrupt-parent = <&aic>; interrupts = <5>; clocks = <&chip_clk CLKID_CFG>; pinctrl-0 = <&twsi1_pmux>; @@ -528,7 +526,6 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x7000 0x100>; - interrupt-parent = <&sic>; interrupts = <6>; clocks = <&refclk>; pinctrl-0 = <&twsi2_pmux>; @@ -541,7 +538,6 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x8000 0x100>; - interrupt-parent = <&sic>; interrupts = <7>; clocks = <&refclk>; pinctrl-0 = <&twsi3_pmux>; @@ -552,7 +548,6 @@ uart0: uart@9000 { compatible = "snps,dw-apb-uart"; reg = <0x9000 0x100>; - interrupt-parent = <&sic>; interrupts = <8>; clocks = <&refclk>; reg-shift = <2>; @@ -564,7 +559,6 @@ uart1: uart@a000 { compatible = "snps,dw-apb-uart"; reg = <0xa000 0x100>; - interrupt-parent = <&sic>; interrupts = <9>; clocks = <&refclk>; reg-shift = <2>; -- cgit v1.2.3 From da0a1cf6af5d26b44ed6ce50d881beacdadb0d63 Mon Sep 17 00:00:00 2001 From: John Keeping Date: Thu, 19 Nov 2015 13:45:31 +0000 Subject: ARM: dts: rockchip: set system-power-controller property on rk3288-rock2 The act8846 on rock2 boards controls the system power, so add the appropriate property to allow turning off the board. Signed-off-by: John Keeping Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-rock2-som.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rk3288-rock2-som.dtsi index 1813b7c36556..1ece66f3e162 100644 --- a/arch/arm/boot/dts/rk3288-rock2-som.dtsi +++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi @@ -109,6 +109,7 @@ act8846: act8846@5a { compatible = "active-semi,act8846"; reg = <0x5a>; + system-power-controller; inl1-supply = <&vcc_io>; inl2-supply = <&vcc_sys>; inl3-supply = <&vcc_20>; -- cgit v1.2.3 From 7ba8cd8bf53adbc4ebdf1e684bf900f11327fcb8 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Tue, 17 Nov 2015 14:55:26 -0500 Subject: ARM: dts: NSP: Device Tree clean-ups Minor changes to the Broadcom Northstar Plus device tree to make it more organized and clean. Firstly, move the GIC and L2 cache entries to be sequential with respect to the memory addresses. Secondly, modify the address portion of the entry names to reflect the difference from the range modification. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 50 +++++++++++++++++++++--------------------- 1 file changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 4bcdd28fd2ac..7335a7478e3e 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -58,30 +58,14 @@ }; }; - L2: l2-cache { - compatible = "arm,pl310-cache"; - reg = <0x2000 0x1000>; - cache-unified; - cache-level = <2>; - }; - - gic: interrupt-controller@19021000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - #address-cells = <0>; - interrupt-controller; - reg = <0x1000 0x1000>, - <0x0100 0x100>; - }; - - timer@19020200 { + timer@0200 { compatible = "arm,cortex-a9-global-timer"; reg = <0x0200 0x100>; interrupts = ; clocks = <&periph_clk>; }; - twd-timer@19020600 { + twd-timer@0600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x0600 0x20>; interrupts = ; }; - twd-watchdog@19020620 { + twd-watchdog@0620 { compatible = "arm,cortex-a9-twd-wdt"; reg = <0x0620 0x20>; interrupts = ; clocks = <&periph_clk>; }; + + gic: interrupt-controller@1000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1000 0x1000>, + <0x0100 0x100>; + }; + + L2: l2-cache { + compatible = "arm,pl310-cache"; + reg = <0x2000 0x1000>; + cache-unified; + cache-level = <2>; + }; }; clocks { @@ -116,7 +116,7 @@ #address-cells = <1>; #size-cells = <1>; - uart0: serial@18000300 { + uart0: serial@0300 { compatible = "ns16550a"; reg = <0x0300 0x100>; interrupts = ; @@ -124,7 +124,7 @@ status = "disabled"; }; - uart1: serial@18000400 { + uart1: serial@0400 { compatible = "ns16550a"; reg = <0x0400 0x100>; interrupts = ; @@ -132,7 +132,7 @@ status = "disabled"; }; - pcie0: pcie@18012000 { + pcie0: pcie@12000 { compatible = "brcm,iproc-pcie"; reg = <0x12000 0x1000>; @@ -156,7 +156,7 @@ status = "disabled"; }; - pcie1: pcie@18013000 { + pcie1: pcie@13000 { compatible = "brcm,iproc-pcie"; reg = <0x13000 0x1000>; @@ -180,7 +180,7 @@ status = "disabled"; }; - pcie2: pcie@18014000 { + pcie2: pcie@14000 { compatible = "brcm,iproc-pcie"; reg = <0x14000 0x1000>; @@ -204,7 +204,7 @@ status = "disabled"; }; - nand: nand@18026000 { + nand: nand@26000 { compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1"; reg = <0x026000 0x600>, <0x11b408 0x600>, -- cgit v1.2.3 From 0f9f27a36d09580e1fd51e091dc99b15a895aa83 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Tue, 17 Nov 2015 14:55:27 -0500 Subject: ARM: dts: NSP: Add I2C support to the DT Add I2C support to the Broadcom Northstar Plus Device Tree. Since no driver changes are needed to enable this hardware, only the device tree changes are required to make this functional. Signed-off-by: Jon Mason Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 7335a7478e3e..b74438c3d3ab 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -217,5 +217,14 @@ brcm,nand-has-wp; }; + + i2c0: i2c@38000 { + compatible = "brcm,iproc-i2c"; + reg = <0x38000 0x50>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + clock-frequency = <100000>; + }; }; }; -- cgit v1.2.3 From aea4c39526132e01a6cb18462ad2c15e7f15da1b Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 17 Nov 2015 00:38:25 +0800 Subject: ARM: dts: sun8i: Add simplefb node labels to reference at board level Some boards, such as tablets, have regulators providing power to parts of the display pipeline, like signal converters and LCD panels. Add labels to the simplefb device nodes so that we can reference them in the board dts files to add regulator supply properties. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a23-a33.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index 0c0964d4fa1f..6f88fb0ddbc7 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -56,7 +56,7 @@ #size-cells = <1>; ranges; - framebuffer@0 { + simplefb_lcd: framebuffer@0 { compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0"; -- cgit v1.2.3 From 02eca1737633728bdafb7ed43be7a2935e52a5d6 Mon Sep 17 00:00:00 2001 From: Erin Lo Date: Tue, 20 Oct 2015 14:34:30 +0800 Subject: Document: DT: Add bindings for mediatek MT2701 SoC Platform This adds a DT binding documentation for the MT2701 SoC from Mediatek. Signed-off-by: Erin Lo Acked-by: Rob Herring Signed-off-by: Matthias Brugger --- Documentation/devicetree/bindings/arm/mediatek.txt | 4 ++++ .../bindings/interrupt-controller/mediatek,sysirq.txt | 1 + Documentation/devicetree/bindings/serial/mtk-uart.txt | 14 +++++++------- .../devicetree/bindings/timer/mediatek,mtk-timer.txt | 1 + Documentation/devicetree/bindings/watchdog/mtk-wdt.txt | 6 +++++- 5 files changed, 18 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 618a91994a18..54f43bc2df44 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -6,6 +6,7 @@ following property: Required root node property: compatible: Must contain one of + "mediatek,mt2701" "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" @@ -17,6 +18,9 @@ compatible: Must contain one of Supported boards: +- Evaluation board for MT2701: + Required root node properties: + - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; - Evaluation board for MT6580: Required root node properties: - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index afef6a85ac51..b8e1674c7837 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -14,6 +14,7 @@ Required properties: "mediatek,mt6582-sysirq" "mediatek,mt6580-sysirq" "mediatek,mt6577-sysirq" + "mediatek,mt2701-sysirq" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Use the same format as specified by GIC in Documentation/devicetree/bindings/arm/gic.txt diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 2d47add34765..a833a016f656 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -2,15 +2,15 @@ Required properties: - compatible should contain: - * "mediatek,mt8135-uart" for MT8135 compatible UARTS + * "mediatek,mt2701-uart" for MT2701 compatible UARTS + * "mediatek,mt6580-uart" for MT6580 compatible UARTS + * "mediatek,mt6582-uart" for MT6582 compatible UARTS + * "mediatek,mt6589-uart" for MT6589 compatible UARTS + * "mediatek,mt6795-uart" for MT6795 compatible UARTS * "mediatek,mt8127-uart" for MT8127 compatible UARTS + * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS - * "mediatek,mt6795-uart" for MT6795 compatible UARTS - * "mediatek,mt6589-uart" for MT6589 compatible UARTS - * "mediatek,mt6582-uart" for MT6582 compatible UARTS - * "mediatek,mt6580-uart" for MT6580 compatible UARTS - * "mediatek,mt6577-uart" for all compatible UARTS (MT8173, MT6795, - MT6589, MT6582, MT6580, MT6577) + * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 64083bc5633c..8ff54eb464dc 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -3,6 +3,7 @@ Mediatek MT6577, MT6572 and MT6589 Timers Required properties: - compatible should contain: + * "mediatek,mt2701-timer" for MT2701 compatible timers * "mediatek,mt6580-timer" for MT6580 compatible timers * "mediatek,mt6589-timer" for MT6589 compatible timers * "mediatek,mt8127-timer" for MT8127 compatible timers diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index af9eb5b8a253..6a00939a059a 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -2,7 +2,11 @@ Mediatek SoCs Watchdog timer Required properties: -- compatible : should be "mediatek,mt6589-wdt" +- compatible should contain: + * "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers + * "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701, + MT6589) + - reg : Specifies base physical address and size of the registers. Example: -- cgit v1.2.3 From 74d25721ee6f4bba2afc751bf20517fbe3f6d77b Mon Sep 17 00:00:00 2001 From: Erin Lo Date: Tue, 20 Oct 2015 14:34:31 +0800 Subject: ARM: dts: mediatek: add MT2701 basic support This adds basic chip support for Mediatek 2701. Signed-off-by: Erin Lo [matthias.bgg@gmail.com: Fixed reg address of mt2701-timer] Signed-off-by: Matthias Brugger --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/mt2701-evb.dts | 29 ++++++++ arch/arm/boot/dts/mt2701.dtsi | 146 ++++++++++++++++++++++++++++++++++++++ arch/arm/mach-mediatek/mediatek.c | 1 + 4 files changed, 177 insertions(+) create mode 100644 arch/arm/boot/dts/mt2701-evb.dts create mode 100644 arch/arm/boot/dts/mt2701.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..ad30daf080ea 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -771,6 +771,7 @@ dtb-$(CONFIG_MACH_DOVE) += \ dove-dove-db.dtb \ dove-sbc-a510.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += \ + mt2701-evb.dtb \ mt6580-evbp1.dtb \ mt6589-aquaris5.dtb \ mt6592-evb.dtb \ diff --git a/arch/arm/boot/dts/mt2701-evb.dts b/arch/arm/boot/dts/mt2701-evb.dts new file mode 100644 index 000000000000..082ca8807c62 --- /dev/null +++ b/arch/arm/boot/dts/mt2701-evb.dts @@ -0,0 +1,29 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Erin Lo + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; +#include "mt2701.dtsi" + +/ { + model = "MediaTek MT2701 evaluation board"; + compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; + + memory { + reg = <0 0x80000000 0 0x40000000>; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi new file mode 100644 index 000000000000..3766904b60f3 --- /dev/null +++ b/arch/arm/boot/dts/mt2701.dtsi @@ -0,0 +1,146 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Erin.Lo + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include "skeleton64.dtsi" + +/ { + compatible = "mediatek,mt2701"; + interrupt-parent = <&sysirq>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x1>; + }; + cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x2>; + }; + cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x3>; + }; + }; + + system_clk: dummy13m { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + rtc_clk: dummy32k { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + uart_clk: dummy26m { + compatible = "fixed-clock"; + clock-frequency = <26000000>; + #clock-cells = <0>; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupt-parent = <&gic>; + interrupts = , + , + , + ; + }; + + watchdog: watchdog@10007000 { + compatible = "mediatek,mt2701-wdt", + "mediatek,mt6589-wdt"; + reg = <0 0x10007000 0 0x100>; + }; + + timer: timer@10008000 { + compatible = "mediatek,mt2701-timer", + "mediatek,mt6577-timer"; + reg = <0 0x10008000 0 0x80>; + interrupts = ; + clocks = <&system_clk>, <&rtc_clk>; + clock-names = "system-clk", "rtc-clk"; + }; + + sysirq: interrupt-controller@10200100 { + compatible = "mediatek,mt2701-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200100 0 0x1c>; + }; + + gic: interrupt-controller@10211000 { + compatible = "arm,cortex-a7-gic"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10211000 0 0x1000>, + <0 0x10212000 0 0x1000>, + <0 0x10214000 0 0x2000>, + <0 0x10216000 0 0x2000>; + }; + + uart0: serial@11002000 { + compatible = "mediatek,mt2701-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x400>; + interrupts = ; + clocks = <&uart_clk>; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt2701-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = ; + clocks = <&uart_clk>; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt2701-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x400>; + interrupts = ; + clocks = <&uart_clk>; + status = "disabled"; + }; + + uart3: serial@11005000 { + compatible = "mediatek,mt2701-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11005000 0 0x400>; + interrupts = ; + clocks = <&uart_clk>; + status = "disabled"; + }; +}; diff --git a/arch/arm/mach-mediatek/mediatek.c b/arch/arm/mach-mediatek/mediatek.c index d019a080a559..2f9f09ac51bd 100644 --- a/arch/arm/mach-mediatek/mediatek.c +++ b/arch/arm/mach-mediatek/mediatek.c @@ -44,6 +44,7 @@ static void __init mediatek_timer_init(void) }; static const char * const mediatek_board_dt_compat[] = { + "mediatek,mt2701", "mediatek,mt6589", "mediatek,mt6592", "mediatek,mt8127", -- cgit v1.2.3 From e241657de0ced9b40cad126f461b23a8d6c1b563 Mon Sep 17 00:00:00 2001 From: Sugar Zhang Date: Tue, 10 Nov 2015 15:32:09 +0800 Subject: ARM: dts: rockchip: add channels properties for i2s add playback and capture properties to compatible various chips. Signed-off-by: Sugar Zhang Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3066a.dtsi | 6 ++++++ arch/arm/boot/dts/rk3188.dtsi | 2 ++ arch/arm/boot/dts/rk3288.dtsi | 2 ++ 3 files changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rk3066a.dtsi index 946f18705e96..1003f9c1ca8a 100644 --- a/arch/arm/boot/dts/rk3066a.dtsi +++ b/arch/arm/boot/dts/rk3066a.dtsi @@ -103,6 +103,8 @@ dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; + rockchip,playback-channels = <8>; + rockchip,capture-channels = <2>; status = "disabled"; }; @@ -118,6 +120,8 @@ dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S1>, <&cru SCLK_I2S1>; + rockchip,playback-channels = <2>; + rockchip,capture-channels = <2>; status = "disabled"; }; @@ -133,6 +137,8 @@ dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S2>, <&cru SCLK_I2S2>; + rockchip,playback-channels = <2>; + rockchip,capture-channels = <2>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi index 6399942f1840..42a67d8fe129 100644 --- a/arch/arm/boot/dts/rk3188.dtsi +++ b/arch/arm/boot/dts/rk3188.dtsi @@ -118,6 +118,8 @@ dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; + rockchip,playback-channels = <2>; + rockchip,capture-channels = <2>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 16187c39d035..2040a1b0cf76 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -776,6 +776,8 @@ clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; pinctrl-names = "default"; pinctrl-0 = <&i2s0_bus>; + rockchip,playback-channels = <8>; + rockchip,capture-channels = <2>; status = "disabled"; }; -- cgit v1.2.3 From a292e576f533070b39547077a5662d33f6c3ed07 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:47:11 +0100 Subject: ARM: dts: sun4i: Enable onboard codec used on the iNet1 tablet The iNet1 tablet uses the A10's integrated audio codec, enable it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-inet1.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts index 487ce63519dc..0711fa26ca67 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet1.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -61,6 +61,10 @@ }; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; -- cgit v1.2.3 From 8a7b89d1f674c5202908935267fcade13c83f76e Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:59:07 +0100 Subject: ARM: dts: sun4i: Add backlight node to iNet1 tablet Add a node describing the lcd panel backlight on the iNet1 tablet. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-inet1.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts index 0711fa26ca67..d46a141bb847 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet1.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -47,6 +47,7 @@ #include #include #include +#include / { model = "iNet-1"; @@ -56,6 +57,16 @@ serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&bl_en_pin_inet>; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + }; + chosen { stdout-path = "serial0:115200n8"; }; @@ -155,6 +166,13 @@ }; &pio { + bl_en_pin_inet: bl_en_pin@0 { + allwinner,pins = "PH7"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; @@ -170,6 +188,12 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; -- cgit v1.2.3 From 45f0cf84ac7096e76a6fffa17c43d25b50d86d05 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:59:08 +0100 Subject: ARM: dts: sun5i: Add backlight node to UTOO P66 tablet Add a node describing the lcd panel backlight on the UTOO P66 tablet. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i-a13-utoo-p66.dts | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts index eb793d5a2bd6..5236c1e3a1b5 100644 --- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts +++ b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts @@ -47,11 +47,21 @@ #include #include #include +#include / { model = "Utoo P66"; compatible = "utoo,p66", "allwinner,sun5i-a13"; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + /* Note levels of 10 / 20% result in backlight off */ + brightness-levels = <0 30 40 50 60 70 80 90 100>; + default-brightness-level = <6>; + /* TODO: backlight uses axp gpio1 as enable pin */ + }; + i2c_lcd: i2c@0 { /* The lcd panel i2c interface is hooked up via gpios */ compatible = "i2c-gpio"; @@ -201,6 +211,12 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; -- cgit v1.2.3 From 0f95851bbc9997bc7ee94180b4058bf376b4473a Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:59:09 +0100 Subject: ARM: dts: sun4i: Add backlight node to pov protab2 ips9 tablet Add a node describing the lcd panel backlight on the pov protab2 ips9 tablet. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts index 82e69c3820a2..d1ea36cd216b 100644 --- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -47,6 +47,7 @@ #include #include #include +#include / { model = "Point of View Protab2-IPS9"; @@ -56,6 +57,16 @@ serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&bl_en_pin_protab>; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + }; + chosen { stdout-path = "serial0:115200n8"; }; @@ -129,6 +140,13 @@ }; &pio { + bl_en_pin_protab: bl_en_pin@0 { + allwinner,pins = "PH7"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; @@ -144,6 +162,12 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; -- cgit v1.2.3 From c9bb9aedb04986e55f269484556330f5b74d76ff Mon Sep 17 00:00:00 2001 From: Michael van Slingerland Date: Fri, 20 Nov 2015 14:59:10 +0100 Subject: ARM: dts: sun5i: Add i2c axp152 pmic support for Auxtek T004 boards Add a node describing the AXP152 pmic used on Auxtek T004 boards. Acked-by: Chen-Yu Tsai Signed-off-by: Michael van Slingerland Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts index 2b3511ea2e5d..a790ec8adb75 100644 --- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts @@ -86,6 +86,20 @@ status = "okay"; }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp152: pmic@30 { + compatible = "x-powers,axp152"; + reg = <0x30>; + interrupts = <0>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>; -- cgit v1.2.3 From cdc36b22f0e4b8badf3db14395f0aa44dcbce4b3 Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Fri, 20 Nov 2015 10:17:18 -0500 Subject: ARM: dts: enable clock support for BCM5301X Replace current device tree dummy clocks with real clock support for Broadcom Northstar SoCs. Signed-off-by: Jon Mason Reviewed-by: Ray Jui Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm5301x.dtsi | 92 +++++++++++++++++++++++++++++++---------- 1 file changed, 71 insertions(+), 21 deletions(-) diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi index 6f50f672efbd..65a1309bd6e2 100644 --- a/arch/arm/boot/dts/bcm5301x.dtsi +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -8,6 +8,7 @@ * Licensed under the GNU/GPL. See COPYING for details. */ +#include #include #include #include @@ -27,7 +28,7 @@ compatible = "ns16550"; reg = <0x0300 0x100>; interrupts = ; - clock-frequency = <100000000>; + clocks = <&iprocslow>; status = "disabled"; }; @@ -35,48 +36,55 @@ compatible = "ns16550"; reg = <0x0400 0x100>; interrupts = ; - clock-frequency = <100000000>; + clocks = <&iprocslow>; status = "disabled"; }; }; mpcore { compatible = "simple-bus"; - ranges = <0x00000000 0x19020000 0x00003000>; + ranges = <0x00000000 0x19000000 0x00023000>; #address-cells = <1>; #size-cells = <1>; - scu@0000 { + a9pll: arm_clk@00000 { + #clock-cells = <0>; + compatible = "brcm,nsp-armpll"; + clocks = <&osc>; + reg = <0x00000 0x1000>; + }; + + scu@20000 { compatible = "arm,cortex-a9-scu"; - reg = <0x0000 0x100>; + reg = <0x20000 0x100>; }; - timer@0200 { + timer@20200 { compatible = "arm,cortex-a9-global-timer"; - reg = <0x0200 0x100>; + reg = <0x20200 0x100>; interrupts = ; - clocks = <&clk_periph>; + clocks = <&periph_clk>; }; - local-timer@0600 { + local-timer@20600 { compatible = "arm,cortex-a9-twd-timer"; - reg = <0x0600 0x100>; + reg = <0x20600 0x100>; interrupts = ; - clocks = <&clk_periph>; + clocks = <&periph_clk>; }; - gic: interrupt-controller@1000 { + gic: interrupt-controller@21000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; #address-cells = <0>; interrupt-controller; - reg = <0x1000 0x1000>, - <0x0100 0x100>; + reg = <0x21000 0x1000>, + <0x20100 0x100>; }; - L2: cache-controller@2000 { + L2: cache-controller@22000 { compatible = "arm,pl310-cache"; - reg = <0x2000 0x1000>; + reg = <0x22000 0x1000>; cache-unified; arm,shared-override; prefetch-data = <1>; @@ -94,14 +102,37 @@ clocks { #address-cells = <1>; - #size-cells = <0>; + #size-cells = <1>; + ranges; - /* As long as we do not have a real clock driver us this - * fixed clock */ - clk_periph: periph { + osc: oscillator { + #clock-cells = <0>; compatible = "fixed-clock"; + clock-frequency = <25000000>; + }; + + iprocmed: iprocmed { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; + clock-div = <2>; + clock-mult = <1>; + }; + + iprocslow: iprocslow { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; + clock-div = <4>; + clock-mult = <1>; + }; + + periph_clk: periph_clk { #clock-cells = <0>; - clock-frequency = <400000000>; + compatible = "fixed-factor-clock"; + clocks = <&a9pll>; + clock-div = <2>; + clock-mult = <1>; }; }; @@ -178,6 +209,25 @@ }; }; + lcpll0: lcpll0@1800c100 { + #clock-cells = <1>; + compatible = "brcm,nsp-lcpll0"; + reg = <0x1800c100 0x14>; + clocks = <&osc>; + clock-output-names = "lcpll0", "pcie_phy", "sdio", + "ddr_phy"; + }; + + genpll: genpll@1800c140 { + #clock-cells = <1>; + compatible = "brcm,nsp-genpll"; + reg = <0x1800c140 0x24>; + clocks = <&osc>; + clock-output-names = "genpll", "phy", "ethernetclk", + "usbclk", "iprocfast", "sata1", + "sata2"; + }; + nand: nand@18028000 { compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand"; reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>; -- cgit v1.2.3 From da3f974263a81c03b699b9d6ef2684c259526fde Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Fri, 20 Nov 2015 10:17:19 -0500 Subject: ARM: dts: enable clock support for Broadcom NSP Replace current device tree dummy clocks with real clock support for Broadcom Northstar Plus SoC Signed-off-by: Jon Mason Reviewed-by: Ray Jui Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 81 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 66 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index b74438c3d3ab..d9bfc5618c25 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -32,6 +32,7 @@ #include #include +#include #include "skeleton.dtsi" @@ -42,7 +43,7 @@ mpcore { compatible = "simple-bus"; - ranges = <0x00000000 0x19020000 0x00003000>; + ranges = <0x00000000 0x19000000 0x00023000>; #address-cells = <1>; #size-cells = <1>; @@ -58,41 +59,48 @@ }; }; - timer@0200 { + a9pll: arm_clk@00000 { + #clock-cells = <0>; + compatible = "brcm,nsp-armpll"; + clocks = <&osc>; + reg = <0x00000 0x1000>; + }; + + timer@20200 { compatible = "arm,cortex-a9-global-timer"; - reg = <0x0200 0x100>; + reg = <0x20200 0x100>; interrupts = ; clocks = <&periph_clk>; }; - twd-timer@0600 { + twd-timer@20600 { compatible = "arm,cortex-a9-twd-timer"; - reg = <0x0600 0x20>; + reg = <0x20600 0x20>; interrupts = ; clocks = <&periph_clk>; }; - twd-watchdog@0620 { + twd-watchdog@20620 { compatible = "arm,cortex-a9-twd-wdt"; - reg = <0x0620 0x20>; + reg = <0x20620 0x20>; interrupts = ; clocks = <&periph_clk>; }; - gic: interrupt-controller@1000 { + gic: interrupt-controller@21000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; #address-cells = <0>; interrupt-controller; - reg = <0x1000 0x1000>, - <0x0100 0x100>; + reg = <0x21000 0x1000>, + <0x20100 0x100>; }; L2: l2-cache { compatible = "arm,pl310-cache"; - reg = <0x2000 0x1000>; + reg = <0x22000 0x1000>; cache-unified; cache-level = <2>; }; @@ -103,10 +111,34 @@ #size-cells = <1>; ranges; - periph_clk: periph_clk { + osc: oscillator { + #clock-cells = <0>; compatible = "fixed-clock"; + clock-frequency = <25000000>; + }; + + iprocmed: iprocmed { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; + clock-div = <2>; + clock-mult = <1>; + }; + + iprocslow: iprocslow { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; + clock-div = <4>; + clock-mult = <1>; + }; + + periph_clk: periph_clk { #clock-cells = <0>; - clock-frequency = <500000000>; + compatible = "fixed-factor-clock"; + clocks = <&a9pll>; + clock-div = <2>; + clock-mult = <1>; }; }; @@ -120,7 +152,7 @@ compatible = "ns16550a"; reg = <0x0300 0x100>; interrupts = ; - clock-frequency = <62499840>; + clocks = <&osc>; status = "disabled"; }; @@ -128,7 +160,7 @@ compatible = "ns16550a"; reg = <0x0400 0x100>; interrupts = ; - clock-frequency = <62499840>; + clocks = <&osc>; status = "disabled"; }; @@ -226,5 +258,24 @@ interrupts = ; clock-frequency = <100000>; }; + + lcpll0: lcpll0@3f100 { + #clock-cells = <1>; + compatible = "brcm,nsp-lcpll0"; + reg = <0x3f100 0x14>; + clocks = <&osc>; + clock-output-names = "lcpll0", "pcie_phy", "sdio", + "ddr_phy"; + }; + + genpll: genpll@3f140 { + #clock-cells = <1>; + compatible = "brcm,nsp-genpll"; + reg = <0x3f140 0x24>; + clocks = <&osc>; + clock-output-names = "genpll", "phy", "ethernetclk", + "usbclk", "iprocfast", "sata1", + "sata2"; + }; }; }; -- cgit v1.2.3 From 3a035ea0e9e92614efe08465813b16aa40048d7c Mon Sep 17 00:00:00 2001 From: Sjoerd Simons Date: Mon, 23 Nov 2015 15:36:28 +0100 Subject: ARM: dts: rockchip: Add IR receiver to RK3288 Radxa Rock 2 Square Add support for the IR receiver as present on the Radxa Rock 2 Square board. Signed-off-by: Sjoerd Simons Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-rock2-square.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts b/arch/arm/boot/dts/rk3288-rock2-square.dts index 8af35c867a80..c5453a0b07fc 100644 --- a/arch/arm/boot/dts/rk3288-rock2-square.dts +++ b/arch/arm/boot/dts/rk3288-rock2-square.dts @@ -49,6 +49,13 @@ stdout-path = "serial2:115200n8"; }; + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio8 1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + sound { compatible = "simple-audio-card"; simple-audio-card,name = "SPDIF"; @@ -131,6 +138,12 @@ }; &pinctrl { + ir { + ir_int: ir-int { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + pmic { pmic_int: pmic-int { rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>; -- cgit v1.2.3 From 71101fdf05a141c65363ecfb3f085d9e847138b7 Mon Sep 17 00:00:00 2001 From: Stefan Monnier Date: Mon, 23 Nov 2015 13:50:16 -0500 Subject: ARM: dts: sun7i: Enable audio codec on OrangePi Mini Enable the on-chip audio codec Signed-off-by: Stefan Monnier Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts index 4f65664e5dfe..2be04c438b1e 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts @@ -95,6 +95,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &ehci0 { status = "okay"; }; -- cgit v1.2.3 From 38e633f3f3756b5630c5eb66042e776d86764296 Mon Sep 17 00:00:00 2001 From: Stefan Monnier Date: Mon, 23 Nov 2015 13:50:17 -0500 Subject: ARM: dts: sun7i: Enable audio codec on BananaPi Enable the on-chip audio codec Signed-off-by: Stefan Monnier Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-bananapi.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index fd7594ff90d5..67c8a7644b99 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -92,6 +92,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; operating-points = < -- cgit v1.2.3 From faea098e1808729e4785cdba3a3fc52fae49f1ab Mon Sep 17 00:00:00 2001 From: Xing Zheng Date: Thu, 5 Nov 2015 15:39:52 +0800 Subject: ARM: dts: rockchip: add core rk3036 dtsi Initial release for rk3036 shared dtsi. Signed-off-by: Xing Zheng Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3036.dtsi | 554 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 554 insertions(+) create mode 100644 arch/arm/boot/dts/rk3036.dtsi diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi new file mode 100644 index 000000000000..f8758bf15933 --- /dev/null +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -0,0 +1,554 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include +#include +#include +#include +#include +#include "skeleton.dtsi" + +/ { + compatible = "rockchip,rk3036"; + + interrupt-parent = <&gic>; + + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + mshc0 = &emmc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + memory { + device_type = "memory"; + reg = <0x60000000 0x40000000>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "rockchip,rk3036-smp"; + + cpu0: cpu@f00 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf00>; + resets = <&cru SRST_CORE0>; + operating-points = < + /* KHz uV */ + 816000 1000000 + >; + clock-latency = <40000>; + clocks = <&cru ARMCLK>; + }; + + cpu1: cpu@f01 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf01>; + resets = <&cru SRST_CORE1>; + }; + }; + + amba { + compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pdma: pdma@20078000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x20078000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + clocks = <&cru ACLK_DMAC2>; + clock-names = "apb_pclk"; + }; + }; + + arm-pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts = , + ; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + + timer { + compatible = "arm,armv7-timer"; + arm,cpu-registers-not-fw-configured; + interrupts = , + , + , + ; + clock-frequency = <24000000>; + }; + + xin24m: oscillator { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xin24m"; + #clock-cells = <0>; + }; + + bus_intmem@10080000 { + compatible = "mmio-sram"; + reg = <0x10080000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x10080000 0x2000>; + + smp-sram@0 { + compatible = "rockchip,rk3066-smp-sram"; + reg = <0x00 0x10>; + }; + }; + + gic: interrupt-controller@10139000 { + compatible = "arm,gic-400"; + interrupt-controller; + #interrupt-cells = <3>; + #address-cells = <0>; + + reg = <0x10139000 0x1000>, + <0x1013a000 0x1000>, + <0x1013c000 0x2000>, + <0x1013e000 0x2000>; + interrupts = ; + }; + + usb_otg: usb@10180000 { + compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", + "snps,dwc2"; + reg = <0x10180000 0x40000>; + interrupts = ; + clocks = <&cru HCLK_OTG0>; + clock-names = "otg"; + dr_mode = "otg"; + g-np-tx-fifo-size = <16>; + g-rx-fifo-size = <275>; + g-tx-fifo-size = <256 128 128 64 64 32>; + g-use-dma; + status = "disabled"; + }; + + usb_host: usb@101c0000 { + compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", + "snps,dwc2"; + reg = <0x101c0000 0x40000>; + interrupts = ; + clocks = <&cru HCLK_OTG1>; + clock-names = "otg"; + dr_mode = "host"; + status = "disabled"; + }; + + emmc: dwmmc@1021c000 { + compatible = "rockchip,rk3288-dw-mshc"; + reg = <0x1021c000 0x4000>; + interrupts = ; + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + clock-frequency = <37500000>; + clock-freq-min-max = <400000 37500000>; + clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, + <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; + default-sample-phase = <158>; + disable-wp; + dmas = <&pdma 12>; + dma-names = "rx-tx"; + fifo-depth = <0x100>; + mmc-ddr-1_8v; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; + status = "disabled"; + }; + + i2s: i2s@10220000 { + compatible = "rockchip,rk3036-i2s", "rockchip,rk3066-i2s"; + reg = <0x10220000 0x4000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2s_hclk", "i2s_clk"; + clocks = <&cru HCLK_I2S>, <&cru SCLK_I2S>; + dmas = <&pdma 0>, <&pdma 1>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s_bus>; + status = "disabled"; + }; + + cru: clock-controller@20000000 { + compatible = "rockchip,rk3036-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = <&cru PLL_GPLL>; + assigned-clock-rates = <594000000>; + }; + + grf: syscon@20008000 { + compatible = "rockchip,rk3036-grf", "syscon"; + reg = <0x20008000 0x1000>; + }; + + acodec: acodec-ana@20030000 { + compatible = "rk3036-codec"; + reg = <0x20030000 0x4000>; + rockchip,grf = <&grf>; + clock-names = "acodec_pclk"; + clocks = <&cru PCLK_ACODEC>; + status = "disabled"; + }; + + timer: timer@20044000 { + compatible = "rockchip,rk3036-timer", "rockchip,rk3288-timer"; + reg = <0x20044000 0x20>; + interrupts = ; + clocks = <&xin24m>, <&cru PCLK_TIMER>; + clock-names = "timer", "pclk"; + }; + + pwm0: pwm@20050000 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050000 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + status = "disabled"; + }; + + pwm1: pwm@20050010 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050010 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_pin>; + status = "disabled"; + }; + + pwm2: pwm@20050020 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050020 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pin>; + status = "disabled"; + }; + + pwm3: pwm@20050030 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050030 0x10>; + #pwm-cells = <2>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pin>; + status = "disabled"; + }; + + i2c1: i2c@20056000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x20056000 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C1>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_xfer>; + status = "disabled"; + }; + + i2c2: i2c@2005a000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x2005a000 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C2>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_xfer>; + status = "disabled"; + }; + + uart0: serial@20060000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20060000 0x100>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; + status = "disabled"; + }; + + uart1: serial@20064000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20064000 0x100>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_xfer>; + status = "disabled"; + }; + + uart2: serial@20068000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20068000 0x100>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; + status = "disabled"; + }; + + i2c0: i2c@20072000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x20072000 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_xfer>; + status = "disabled"; + }; + + pinctrl: pinctrl { + compatible = "rockchip,rk3036-pinctrl"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@2007c000 { + compatible = "rockchip,gpio-bank"; + reg = <0x2007c000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO0>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio1@20080000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20080000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio2@20084000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20084000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO2>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + pcfg_pull_up: pcfg-pull-up { + bias-pull-up; + }; + + pcfg_pull_down: pcfg-pull-down { + bias-pull-down; + }; + + pcfg_pull_none: pcfg-pull-none { + bias-disable; + }; + + pwm0 { + pwm0_pin: pwm0-pin { + rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm1 { + pwm1_pin: pwm1-pin { + rockchip,pins = <0 1 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm2 { + pwm2_pin: pwm2-pin { + rockchip,pins = <0 1 2 &pcfg_pull_none>; + }; + }; + + pwm3 { + pwm3_pin: pwm3-pin { + rockchip,pins = <0 27 1 &pcfg_pull_none>; + }; + }; + + emmc { + /* + * We run eMMC at max speed; bump up drive strength. + * We also have external pulls, so disable the internal ones. + */ + emmc_clk: emmc-clk { + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_cmd: emmc-cmd { + rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_bus8: emmc-bus8 { + rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>, + <1 25 RK_FUNC_2 &pcfg_pull_none>, + <1 26 RK_FUNC_2 &pcfg_pull_none>, + <1 27 RK_FUNC_2 &pcfg_pull_none>, + <1 28 RK_FUNC_2 &pcfg_pull_none>, + <1 29 RK_FUNC_2 &pcfg_pull_none>, + <1 30 RK_FUNC_2 &pcfg_pull_none>, + <1 31 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c0 { + i2c0_xfer: i2c0-xfer { + rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>, + <0 1 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c1 { + i2c1_xfer: i2c1-xfer { + rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>, + <0 3 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c2 { + i2c2_xfer: i2c2-xfer { + rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>, + <2 21 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2s { + i2s_bus: i2s-bus { + rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_none>, + <1 1 RK_FUNC_1 &pcfg_pull_none>, + <1 2 RK_FUNC_1 &pcfg_pull_none>, + <1 3 RK_FUNC_1 &pcfg_pull_none>, + <1 4 RK_FUNC_1 &pcfg_pull_none>, + <1 5 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart0 { + uart0_xfer: uart0-xfer { + rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_up>, + <0 17 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_cts: uart0-cts { + rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_up>; + }; + + uart0_rts: uart0-rts { + rockchip,pins = <0 19 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart1 { + uart1_xfer: uart1-xfer { + rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_none>, + <2 23 RK_FUNC_1 &pcfg_pull_none>; + }; + /* no rts / cts for uart1 */ + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>, + <1 19 RK_FUNC_2 &pcfg_pull_none>; + }; + /* no rts / cts for uart2 */ + }; + }; +}; -- cgit v1.2.3 From faef90f1a203f96796d5bc3c6225ee100ec70864 Mon Sep 17 00:00:00 2001 From: Xing Zheng Date: Thu, 5 Nov 2015 15:39:52 +0800 Subject: ARM: dts: rockchip: add rk3036-evb board Initial release for rk3036 sdk board. Signed-off-by: Xing Zheng Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3036-evb.dts | 64 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+) create mode 100644 arch/arm/boot/dts/rk3036-evb.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..87c875247518 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -512,6 +512,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ dtb-$(CONFIG_ARCH_REALVIEW) += \ arm-realview-pb1176.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += \ + rk3036-evb.dtb \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ rk3066a-rayeager.dtb \ diff --git a/arch/arm/boot/dts/rk3036-evb.dts b/arch/arm/boot/dts/rk3036-evb.dts new file mode 100644 index 000000000000..28a033666017 --- /dev/null +++ b/arch/arm/boot/dts/rk3036-evb.dts @@ -0,0 +1,64 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3036.dtsi" + +/ { + model = "Rockchip RK3036 Evaluation board"; + compatible = "rockchip,rk3036-evb", "rockchip,rk3036"; +}; + +&i2c1 { + status = "okay"; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + }; +}; + +&uart2 { + status = "okay"; +}; -- cgit v1.2.3 From 430d7baddf2d913de76e8101d807f4f2861705f7 Mon Sep 17 00:00:00 2001 From: Ulrich Hecht Date: Fri, 13 Nov 2015 17:22:23 +0100 Subject: ARM: shmobile: r8a7790: switch console back to scif0 The boot loader uses scif0, and so must we if we want earlycon to work. Partially reverts 7c0558941 ("ARM: shmobile: r8a7790: switch from scif to scifa"). Signed-off-by: Ulrich Hecht Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790-lager.dts | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index e2174d816e78..79f141188d99 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -47,13 +47,13 @@ compatible = "renesas,lager", "renesas,r8a7790"; aliases { - serial0 = &scifa0; + serial0 = &scif0; serial1 = &scifa1; }; chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scifa0; + stdout-path = &scif0; }; memory@40000000 { @@ -296,9 +296,9 @@ renesas,function = "du"; }; - scifa0_pins: serial0 { - renesas,groups = "scifa0_data"; - renesas,function = "scifa0"; + scif0_pins: serial0 { + renesas,groups = "scif0_data"; + renesas,function = "scif0"; }; ether_pins: ether { @@ -467,8 +467,8 @@ }; }; -&scifa0 { - pinctrl-0 = <&scifa0_pins>; +&scif0 { + pinctrl-0 = <&scif0_pins>; pinctrl-names = "default"; status = "okay"; -- cgit v1.2.3 From 781f278a16fbd74ffa2acf3f14134953631f076d Mon Sep 17 00:00:00 2001 From: Ulrich Hecht Date: Thu, 29 Oct 2015 20:57:34 +0100 Subject: ARM: shmobile: bockw dts: define sdhi0 pins with pull-ups Ensures that the pull-ups for pins SD0_CD and SD0_WP are enabled. This is one of two features from the DT reference platform that are still missing in MP. Signed-off-by: Ulrich Hecht Acked-by: Linus Walleij Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778-bockw.dts | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index 90543b12d7e2..8a5407678717 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -137,10 +137,14 @@ }; sdhi0_pins: sd0 { - renesas,groups = "sdhi0_data4", "sdhi0_ctrl", - "sdhi0_cd"; + renesas,groups = "sdhi0_data4", "sdhi0_ctrl"; renesas,function = "sdhi0"; }; + sdhi0_pup_pins: sd0_pup { + renesas,groups = "sdhi0_cd", "sdhi0_wp"; + renesas,function = "sdhi0"; + bias-pull-up; + }; hspi0_pins: hspi0 { renesas,groups = "hspi0_a"; @@ -169,7 +173,7 @@ }; &sdhi0 { - pinctrl-0 = <&sdhi0_pins>; + pinctrl-0 = <&sdhi0_pins>, <&sdhi0_pup_pins>; pinctrl-names = "default"; vmmc-supply = <&fixedregulator3v3>; -- cgit v1.2.3 From 13b8b8e8fae6bc38941bc5e5e847706beb004082 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 17 Nov 2015 12:27:59 +0900 Subject: ARM: shmobile: r8a7794: alt: Enable PFC DU for the VGA port Tie in r8a7794 PFC DU support to the VGA port on the r8a7794 ALT board. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index fd1cfcdd65ef..b255a8791841 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -80,6 +80,8 @@ }; &du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; status = "okay"; clocks = <&mstp7_clks R8A7794_CLK_DU0>, @@ -101,6 +103,11 @@ }; &pfc { + du_pins: du { + renesas,groups = "du1_rgb666", "du1_sync", "du1_disp", "du1_dotclkout0"; + renesas,function = "du"; + }; + scif2_pins: serial2 { renesas,groups = "scif2_data"; renesas,function = "scif2"; -- cgit v1.2.3 From 6ffd6fa0134a7dd6b65633bb0b8c587517ac94e9 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:24:51 +0100 Subject: ARM: dts: sun4i: Add touchscreen node to iNet1 tablet Add a node describing the touchscreen controller used on the iNet1 tablet. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-inet1.dts | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts index d46a141bb847..e09053bf5e1f 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet1.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -119,6 +119,19 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins_a>; status = "okay"; + + ft5x: touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_wake_pin>; + wake-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* PB13 */ + touchscreen-size-x = <600>; + touchscreen-size-y = <1024>; + touchscreen-swapped-x-y; + }; }; &lradc { @@ -173,6 +186,13 @@ allwinner,pull = ; }; + touchscreen_wake_pin: touchscreen_wake_pin@0 { + allwinner,pins = "PB13"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From c1751e32727c5356c4e33c8da33edb782dde6210 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 20 Nov 2015 14:24:52 +0100 Subject: ARM: dts: sun4i: Add touchscreen node to pov protab2-ips9 tablet Add a node describing the touchscreen found on the pov protab2-ips9 tablet. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts index d1ea36cd216b..1f92ec7c82e8 100644 --- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -104,6 +104,22 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins_a>; status = "okay"; + + pixcir_ts@5c { + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_pins>; + compatible = "pixcir,pixcir_tangoc"; + reg = <0x5c>; + interrupt-parent = <&pio>; + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */ + attb-gpio = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */ + enable-gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; + wake-gpios = <&pio 1 13 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <1024>; + touchscreen-size-y = <768>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; }; &lradc { @@ -147,6 +163,13 @@ allwinner,pull = ; }; + touchscreen_pins: touchscreen_pins@0 { + allwinner,pins = "PA5", "PB13"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From 967313e2ec9cb9184e1d6af393c766e87f8eb1fc Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 20 Nov 2015 12:42:44 +0100 Subject: ARM: mediatek: DT: Move reset controller constants into common location By popular vote, the DT binding includes for reset controllers are located in include/dt-bindings/reset/. Move the mediatek reset constants in there, too, to avoid confusion. Signed-off-by: Philipp Zabel Signed-off-by: Matthias Brugger --- .../bindings/arm/mediatek/mediatek,infracfg.txt | 2 +- .../bindings/arm/mediatek/mediatek,pericfg.txt | 2 +- arch/arm/boot/dts/mt8135.dtsi | 2 +- arch/arm64/boot/dts/mediatek/mt8173.dtsi | 2 +- .../dt-bindings/reset-controller/mt8135-resets.h | 64 ---------------------- .../dt-bindings/reset-controller/mt8173-resets.h | 63 --------------------- include/dt-bindings/reset/mt8135-resets.h | 64 ++++++++++++++++++++++ include/dt-bindings/reset/mt8173-resets.h | 63 +++++++++++++++++++++ 8 files changed, 131 insertions(+), 131 deletions(-) delete mode 100644 include/dt-bindings/reset-controller/mt8135-resets.h delete mode 100644 include/dt-bindings/reset-controller/mt8173-resets.h create mode 100644 include/dt-bindings/reset/mt8135-resets.h create mode 100644 include/dt-bindings/reset/mt8173-resets.h diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index f6cd3e4192ff..aaf8d1460c4d 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -18,7 +18,7 @@ The available clocks are defined in dt-bindings/clock/mt*-clk.h. Also it uses the common reset controller binding from Documentation/devicetree/bindings/reset/reset.txt. The available reset outputs are defined in -dt-bindings/reset-controller/mt*-resets.h +dt-bindings/reset/mt*-resets.h Example: diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index f25b85499a6f..2f6ff86df49f 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -18,7 +18,7 @@ The available clocks are defined in dt-bindings/clock/mt*-clk.h. Also it uses the common reset controller binding from Documentation/devicetree/bindings/reset/reset.txt. The available reset outputs are defined in -dt-bindings/reset-controller/mt*-resets.h +dt-bindings/reset/mt*-resets.h Example: diff --git a/arch/arm/boot/dts/mt8135.dtsi b/arch/arm/boot/dts/mt8135.dtsi index cb99b02d2ccc..1d7f92bdcb9c 100644 --- a/arch/arm/boot/dts/mt8135.dtsi +++ b/arch/arm/boot/dts/mt8135.dtsi @@ -15,7 +15,7 @@ #include #include #include -#include +#include #include "skeleton64.dtsi" #include "mt8135-pinfunc.h" diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index 4dd5f93d0303..fd71a87588f1 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -15,7 +15,7 @@ #include #include #include -#include +#include #include "mt8173-pinfunc.h" / { diff --git a/include/dt-bindings/reset-controller/mt8135-resets.h b/include/dt-bindings/reset-controller/mt8135-resets.h deleted file mode 100644 index 1fb629508db2..000000000000 --- a/include/dt-bindings/reset-controller/mt8135-resets.h +++ /dev/null @@ -1,64 +0,0 @@ -/* - * Copyright (c) 2014 MediaTek Inc. - * Author: Flora Fu, MediaTek - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT8135 -#define _DT_BINDINGS_RESET_CONTROLLER_MT8135 - -/* INFRACFG resets */ -#define MT8135_INFRA_EMI_REG_RST 0 -#define MT8135_INFRA_DRAMC0_A0_RST 1 -#define MT8135_INFRA_CCIF0_RST 2 -#define MT8135_INFRA_APCIRQ_EINT_RST 3 -#define MT8135_INFRA_APXGPT_RST 4 -#define MT8135_INFRA_SCPSYS_RST 5 -#define MT8135_INFRA_CCIF1_RST 6 -#define MT8135_INFRA_PMIC_WRAP_RST 7 -#define MT8135_INFRA_KP_RST 8 -#define MT8135_INFRA_EMI_RST 32 -#define MT8135_INFRA_DRAMC0_RST 34 -#define MT8135_INFRA_SMI_RST 35 -#define MT8135_INFRA_M4U_RST 36 - -/* PERICFG resets */ -#define MT8135_PERI_UART0_SW_RST 0 -#define MT8135_PERI_UART1_SW_RST 1 -#define MT8135_PERI_UART2_SW_RST 2 -#define MT8135_PERI_UART3_SW_RST 3 -#define MT8135_PERI_IRDA_SW_RST 4 -#define MT8135_PERI_PTP_SW_RST 5 -#define MT8135_PERI_AP_HIF_SW_RST 6 -#define MT8135_PERI_GPCU_SW_RST 7 -#define MT8135_PERI_MD_HIF_SW_RST 8 -#define MT8135_PERI_NLI_SW_RST 9 -#define MT8135_PERI_AUXADC_SW_RST 10 -#define MT8135_PERI_DMA_SW_RST 11 -#define MT8135_PERI_NFI_SW_RST 14 -#define MT8135_PERI_PWM_SW_RST 15 -#define MT8135_PERI_THERM_SW_RST 16 -#define MT8135_PERI_MSDC0_SW_RST 17 -#define MT8135_PERI_MSDC1_SW_RST 18 -#define MT8135_PERI_MSDC2_SW_RST 19 -#define MT8135_PERI_MSDC3_SW_RST 20 -#define MT8135_PERI_I2C0_SW_RST 22 -#define MT8135_PERI_I2C1_SW_RST 23 -#define MT8135_PERI_I2C2_SW_RST 24 -#define MT8135_PERI_I2C3_SW_RST 25 -#define MT8135_PERI_I2C4_SW_RST 26 -#define MT8135_PERI_I2C5_SW_RST 27 -#define MT8135_PERI_I2C6_SW_RST 28 -#define MT8135_PERI_USB_SW_RST 29 -#define MT8135_PERI_SPI1_SW_RST 33 -#define MT8135_PERI_PWRAP_BRIDGE_SW_RST 34 - -#endif /* _DT_BINDINGS_RESET_CONTROLLER_MT8135 */ diff --git a/include/dt-bindings/reset-controller/mt8173-resets.h b/include/dt-bindings/reset-controller/mt8173-resets.h deleted file mode 100644 index 9464b37cf68c..000000000000 --- a/include/dt-bindings/reset-controller/mt8173-resets.h +++ /dev/null @@ -1,63 +0,0 @@ -/* - * Copyright (c) 2014 MediaTek Inc. - * Author: Flora Fu, MediaTek - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT8173 -#define _DT_BINDINGS_RESET_CONTROLLER_MT8173 - -/* INFRACFG resets */ -#define MT8173_INFRA_EMI_REG_RST 0 -#define MT8173_INFRA_DRAMC0_A0_RST 1 -#define MT8173_INFRA_APCIRQ_EINT_RST 3 -#define MT8173_INFRA_APXGPT_RST 4 -#define MT8173_INFRA_SCPSYS_RST 5 -#define MT8173_INFRA_KP_RST 6 -#define MT8173_INFRA_PMIC_WRAP_RST 7 -#define MT8173_INFRA_MPIP_RST 8 -#define MT8173_INFRA_CEC_RST 9 -#define MT8173_INFRA_EMI_RST 32 -#define MT8173_INFRA_DRAMC0_RST 34 -#define MT8173_INFRA_APMIXEDSYS_RST 35 -#define MT8173_INFRA_MIPI_DSI_RST 36 -#define MT8173_INFRA_TRNG_RST 37 -#define MT8173_INFRA_SYSIRQ_RST 38 -#define MT8173_INFRA_MIPI_CSI_RST 39 -#define MT8173_INFRA_GCE_FAXI_RST 40 -#define MT8173_INFRA_MMIOMMURST 47 - - -/* PERICFG resets */ -#define MT8173_PERI_UART0_SW_RST 0 -#define MT8173_PERI_UART1_SW_RST 1 -#define MT8173_PERI_UART2_SW_RST 2 -#define MT8173_PERI_UART3_SW_RST 3 -#define MT8173_PERI_IRRX_SW_RST 4 -#define MT8173_PERI_PWM_SW_RST 8 -#define MT8173_PERI_AUXADC_SW_RST 10 -#define MT8173_PERI_DMA_SW_RST 11 -#define MT8173_PERI_I2C6_SW_RST 13 -#define MT8173_PERI_NFI_SW_RST 14 -#define MT8173_PERI_THERM_SW_RST 16 -#define MT8173_PERI_MSDC2_SW_RST 17 -#define MT8173_PERI_MSDC3_SW_RST 18 -#define MT8173_PERI_MSDC0_SW_RST 19 -#define MT8173_PERI_MSDC1_SW_RST 20 -#define MT8173_PERI_I2C0_SW_RST 22 -#define MT8173_PERI_I2C1_SW_RST 23 -#define MT8173_PERI_I2C2_SW_RST 24 -#define MT8173_PERI_I2C3_SW_RST 25 -#define MT8173_PERI_I2C4_SW_RST 26 -#define MT8173_PERI_HDMI_SW_RST 29 -#define MT8173_PERI_SPI0_SW_RST 33 - -#endif /* _DT_BINDINGS_RESET_CONTROLLER_MT8173 */ diff --git a/include/dt-bindings/reset/mt8135-resets.h b/include/dt-bindings/reset/mt8135-resets.h new file mode 100644 index 000000000000..1fb629508db2 --- /dev/null +++ b/include/dt-bindings/reset/mt8135-resets.h @@ -0,0 +1,64 @@ +/* + * Copyright (c) 2014 MediaTek Inc. + * Author: Flora Fu, MediaTek + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT8135 +#define _DT_BINDINGS_RESET_CONTROLLER_MT8135 + +/* INFRACFG resets */ +#define MT8135_INFRA_EMI_REG_RST 0 +#define MT8135_INFRA_DRAMC0_A0_RST 1 +#define MT8135_INFRA_CCIF0_RST 2 +#define MT8135_INFRA_APCIRQ_EINT_RST 3 +#define MT8135_INFRA_APXGPT_RST 4 +#define MT8135_INFRA_SCPSYS_RST 5 +#define MT8135_INFRA_CCIF1_RST 6 +#define MT8135_INFRA_PMIC_WRAP_RST 7 +#define MT8135_INFRA_KP_RST 8 +#define MT8135_INFRA_EMI_RST 32 +#define MT8135_INFRA_DRAMC0_RST 34 +#define MT8135_INFRA_SMI_RST 35 +#define MT8135_INFRA_M4U_RST 36 + +/* PERICFG resets */ +#define MT8135_PERI_UART0_SW_RST 0 +#define MT8135_PERI_UART1_SW_RST 1 +#define MT8135_PERI_UART2_SW_RST 2 +#define MT8135_PERI_UART3_SW_RST 3 +#define MT8135_PERI_IRDA_SW_RST 4 +#define MT8135_PERI_PTP_SW_RST 5 +#define MT8135_PERI_AP_HIF_SW_RST 6 +#define MT8135_PERI_GPCU_SW_RST 7 +#define MT8135_PERI_MD_HIF_SW_RST 8 +#define MT8135_PERI_NLI_SW_RST 9 +#define MT8135_PERI_AUXADC_SW_RST 10 +#define MT8135_PERI_DMA_SW_RST 11 +#define MT8135_PERI_NFI_SW_RST 14 +#define MT8135_PERI_PWM_SW_RST 15 +#define MT8135_PERI_THERM_SW_RST 16 +#define MT8135_PERI_MSDC0_SW_RST 17 +#define MT8135_PERI_MSDC1_SW_RST 18 +#define MT8135_PERI_MSDC2_SW_RST 19 +#define MT8135_PERI_MSDC3_SW_RST 20 +#define MT8135_PERI_I2C0_SW_RST 22 +#define MT8135_PERI_I2C1_SW_RST 23 +#define MT8135_PERI_I2C2_SW_RST 24 +#define MT8135_PERI_I2C3_SW_RST 25 +#define MT8135_PERI_I2C4_SW_RST 26 +#define MT8135_PERI_I2C5_SW_RST 27 +#define MT8135_PERI_I2C6_SW_RST 28 +#define MT8135_PERI_USB_SW_RST 29 +#define MT8135_PERI_SPI1_SW_RST 33 +#define MT8135_PERI_PWRAP_BRIDGE_SW_RST 34 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_MT8135 */ diff --git a/include/dt-bindings/reset/mt8173-resets.h b/include/dt-bindings/reset/mt8173-resets.h new file mode 100644 index 000000000000..9464b37cf68c --- /dev/null +++ b/include/dt-bindings/reset/mt8173-resets.h @@ -0,0 +1,63 @@ +/* + * Copyright (c) 2014 MediaTek Inc. + * Author: Flora Fu, MediaTek + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT8173 +#define _DT_BINDINGS_RESET_CONTROLLER_MT8173 + +/* INFRACFG resets */ +#define MT8173_INFRA_EMI_REG_RST 0 +#define MT8173_INFRA_DRAMC0_A0_RST 1 +#define MT8173_INFRA_APCIRQ_EINT_RST 3 +#define MT8173_INFRA_APXGPT_RST 4 +#define MT8173_INFRA_SCPSYS_RST 5 +#define MT8173_INFRA_KP_RST 6 +#define MT8173_INFRA_PMIC_WRAP_RST 7 +#define MT8173_INFRA_MPIP_RST 8 +#define MT8173_INFRA_CEC_RST 9 +#define MT8173_INFRA_EMI_RST 32 +#define MT8173_INFRA_DRAMC0_RST 34 +#define MT8173_INFRA_APMIXEDSYS_RST 35 +#define MT8173_INFRA_MIPI_DSI_RST 36 +#define MT8173_INFRA_TRNG_RST 37 +#define MT8173_INFRA_SYSIRQ_RST 38 +#define MT8173_INFRA_MIPI_CSI_RST 39 +#define MT8173_INFRA_GCE_FAXI_RST 40 +#define MT8173_INFRA_MMIOMMURST 47 + + +/* PERICFG resets */ +#define MT8173_PERI_UART0_SW_RST 0 +#define MT8173_PERI_UART1_SW_RST 1 +#define MT8173_PERI_UART2_SW_RST 2 +#define MT8173_PERI_UART3_SW_RST 3 +#define MT8173_PERI_IRRX_SW_RST 4 +#define MT8173_PERI_PWM_SW_RST 8 +#define MT8173_PERI_AUXADC_SW_RST 10 +#define MT8173_PERI_DMA_SW_RST 11 +#define MT8173_PERI_I2C6_SW_RST 13 +#define MT8173_PERI_NFI_SW_RST 14 +#define MT8173_PERI_THERM_SW_RST 16 +#define MT8173_PERI_MSDC2_SW_RST 17 +#define MT8173_PERI_MSDC3_SW_RST 18 +#define MT8173_PERI_MSDC0_SW_RST 19 +#define MT8173_PERI_MSDC1_SW_RST 20 +#define MT8173_PERI_I2C0_SW_RST 22 +#define MT8173_PERI_I2C1_SW_RST 23 +#define MT8173_PERI_I2C2_SW_RST 24 +#define MT8173_PERI_I2C3_SW_RST 25 +#define MT8173_PERI_I2C4_SW_RST 26 +#define MT8173_PERI_HDMI_SW_RST 29 +#define MT8173_PERI_SPI0_SW_RST 33 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_MT8173 */ -- cgit v1.2.3 From ee94fc9b026dd14dd31d9975a62caebf70472a59 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Mon, 16 Nov 2015 18:15:23 +0900 Subject: ARM: shmobile: r8a7793: Add DU node to device tree Add the DU device with a disabled state. Boards that want to enable the DU need to specify the output topology. Signed-off-by: Laurent Pinchart Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 2378df52aa32..cbcda80f4658 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -344,6 +344,36 @@ status = "disabled"; }; + du: display@feb00000 { + compatible = "renesas,du-r8a7793"; + reg = <0 0xfeb00000 0 0x40000>, + <0 0xfeb90000 0 0x1c>; + reg-names = "du", "lvds.0"; + interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, + <0 268 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_DU0>, + <&mstp7_clks R8A7793_CLK_DU1>, + <&mstp7_clks R8A7793_CLK_LVDS0>; + clock-names = "du.0", "du.1", "lvds.0"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + port@1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + }; + }; + clocks { #address-cells = <2>; #size-cells = <2>; -- cgit v1.2.3 From d3b2385577317d8b51fc3b3b75106dd2de7e7439 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 24 Nov 2015 22:32:22 +0100 Subject: ARM: shmobile: r8a7791: remove deprecated #gpio-range-cells from dtsi Commit a1bc260bb5f5d9 ("gpio: clean up gpio-ranges documentation") declares the above property deprecated. That was more than 2 years ago. Remove it, so it doesn't get copied around needlessly. Signed-off-by: Wolfram Sang Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 3776974e3273..12b2b0f95806 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -509,7 +509,6 @@ pfc: pfc@e6060000 { compatible = "renesas,pfc-r8a7791"; reg = <0 0xe6060000 0 0x250>; - #gpio-range-cells = <3>; }; mmcif0: mmc@ee200000 { -- cgit v1.2.3 From 369d4933db6a515b90d153767159918845eb4f5f Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 24 Nov 2015 22:32:23 +0100 Subject: ARM: shmobile: r8a7794: remove deprecated #gpio-range-cells from dtsi Commit a1bc260bb5f5d9 ("gpio: clean up gpio-ranges documentation") declares the above property deprecated. That was more than 2 years ago. Remove it, so it doesn't get copied around needlessly. Signed-off-by: Wolfram Sang Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 57d188c2bf6d..89e914f2a2cf 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -217,7 +217,6 @@ pfc: pin-controller@e6060000 { compatible = "renesas,pfc-r8a7794"; reg = <0 0xe6060000 0 0x11c>; - #gpio-range-cells = <3>; }; dmac0: dma-controller@e6700000 { -- cgit v1.2.3 From 22a1ae361169d74e845fe91912d084191fa7b4a5 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Wed, 25 Nov 2015 02:01:05 +0200 Subject: ARM: shmobile: r8a7791: koelsch: Fix pinmux for HDMI The signals output by the DU to the HDMI transmitter use full 24-bit RGB. Make sure all pins are properly muxed. Signed-off-by: Laurent Pinchart Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-koelsch.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index 4ec2d1fba7c9..50d7b17c6ebd 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -326,7 +326,7 @@ }; du_pins: du { - renesas,groups = "du_rgb666", "du_sync", "du_disp", "du_clk_out_0"; + renesas,groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0"; renesas,function = "du"; }; -- cgit v1.2.3 From a7d57eec21d06cae06f03bd5ae47080a3dc3e898 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 20 Nov 2015 11:38:52 -0800 Subject: ARM: shmobile: bockw: Move SPI FLASH partition to subnode As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support partitions in a special 'partitions' subnode"), having partitions as direct subnodes of an mtd device is discouraged. Hence move the SPI FLASH partition to a "partitions" subnode. Based on similar work for the koelsch board by Geert Uytterhoeven. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778-bockw.dts | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index 8a5407678717..3c03e6b8261e 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -188,16 +188,19 @@ status = "okay"; flash: flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,s25fl008k", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <104000000>; m25p,fast-read; - partition@0 { - label = "data(spi)"; - reg = <0x00000000 0x00100000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "data(spi)"; + reg = <0x00000000 0x00100000>; + }; }; }; }; -- cgit v1.2.3 From 26fac0eebccec898a7a7670856cbde5583a5ec2e Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 20 Nov 2015 11:38:54 -0800 Subject: ARM: shmobile: porter: Move SPI FLASH partitions to subnode As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support partitions in a special 'partitions' subnode"), having partitions as direct subnodes of an mtd device is discouraged. Hence move the SPI FLASH partitions to a "partitions" subnode. Based on similar work for the koelsch board by Geert Uytterhoeven. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-porter.dts | 33 ++++++++++++++++++--------------- 1 file changed, 18 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index 3e198e7b3ee4..f2dd5356eac8 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -192,8 +192,6 @@ status = "okay"; flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,s25fl512s", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <30000000>; @@ -201,19 +199,24 @@ spi-rx-bus-width = <4>; m25p,fast-read; - partition@0 { - label = "loader_prg"; - reg = <0x00000000 0x00040000>; - read-only; - }; - partition@40000 { - label = "user_prg"; - reg = <0x00040000 0x00400000>; - read-only; - }; - partition@440000 { - label = "flash_fs"; - reg = <0x00440000 0x03bc0000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "loader_prg"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user_prg"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash_fs"; + reg = <0x00440000 0x03bc0000>; + }; }; }; }; -- cgit v1.2.3 From f58bac70bf2d6cd9ff852d58199b598bfa6365c6 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 20 Nov 2015 11:38:53 -0800 Subject: ARM: shmobile: lager: Move SPI FLASH partitions to subnode As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support partitions in a special 'partitions' subnode"), having partitions as direct subnodes of an mtd device is discouraged. Hence move the SPI FLASH partitions to a "partitions" subnode. Based on similar work for the koelsch board by Geert Uytterhoeven. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790-lager.dts | 33 ++++++++++++++++++--------------- 1 file changed, 18 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 79f141188d99..c46295afb08a 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -439,8 +439,6 @@ status = "okay"; flash: flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,s25fl512s", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <30000000>; @@ -450,19 +448,24 @@ spi-cpol; m25p,fast-read; - partition@0 { - label = "loader"; - reg = <0x00000000 0x00040000>; - read-only; - }; - partition@40000 { - label = "user"; - reg = <0x00040000 0x00400000>; - read-only; - }; - partition@440000 { - label = "flash"; - reg = <0x00440000 0x03bc0000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash"; + reg = <0x00440000 0x03bc0000>; + }; }; }; }; -- cgit v1.2.3 From 99e14b36594cb6d6fb59aa44999c1f72508af348 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 20 Nov 2015 11:38:55 -0800 Subject: ARM: shmobile: silk: Move SPI FLASH partitions to subnode As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support partitions in a special 'partitions' subnode"), having partitions as direct subnodes of an mtd device is discouraged. Hence move the SPI FLASH partitions to a "partitions" subnode. Based on similar work for the koelsch board by Geert Uytterhoeven. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-silk.dts | 33 ++++++++++++++++++--------------- 1 file changed, 18 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index a49942b626c8..58f0ddf21c17 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -194,8 +194,6 @@ status = "okay"; flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,s25fl512s", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <30000000>; @@ -205,19 +203,24 @@ spi-cpha; m25p,fast-read; - partition@0 { - label = "loader"; - reg = <0x00000000 0x00040000>; - read-only; - }; - partition@40000 { - label = "user"; - reg = <0x00040000 0x00400000>; - read-only; - }; - partition@440000 { - label = "flash"; - reg = <0x00440000 0x03bc0000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash"; + reg = <0x00440000 0x03bc0000>; + }; }; }; }; -- cgit v1.2.3 From 7256587cf15e349b7241e4cc70e4132976765e1f Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Tue, 24 Nov 2015 11:16:04 +0900 Subject: ARM: shmobile: alt: Correct scif2 pfc 22b160713cb6 ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins to the alt device tree but did not reference them. This patch fixes scif2 pfc by adding references to the scif2 pins. Reported-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index b255a8791841..c8cafc1d55c3 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -189,5 +189,8 @@ }; &scif2 { + pinctrl-0 = <&scif2_pins>; + pinctrl-names = "default"; + status = "okay"; }; -- cgit v1.2.3 From c175e7abf75f174a781d1218aa6fb2bdf2ff3eae Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Tue, 24 Nov 2015 11:16:05 +0900 Subject: ARM: shmobile: alt: Correct ether pfc 22b160713cb6 ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins to the alt device tree but did not reference them. This patch fixes ether pfc by: * Referencing ether pins * Adding and referencing phy1 pins * Removing ether b pins. These are not used in the configuration of the alt board used for testing and empirically their presence prevents ethernet from functioning correctly in that environment. Reported-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index c8cafc1d55c3..767d9224d6cc 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -118,9 +118,9 @@ renesas,function = "eth"; }; - ether_b_pins: ether { - renesas,groups = "eth_link_b", "eth_mdio_b", "eth_rmii_b"; - renesas,function = "eth"; + phy1_pins: phy1 { + renesas,groups = "intc_irq8"; + renesas,function = "intc"; }; i2c1_pins: i2c1 { @@ -139,6 +139,9 @@ }; ðer { + pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-names = "default"; + phy-handle = <&phy1>; renesas,ether-link-active-low; status = "okay"; -- cgit v1.2.3 From 374e70075e58acfe922869aad1202b29f8fb76f5 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 23 Nov 2015 14:55:59 +0100 Subject: ARM: shmobile: r8a7740 dtsi: Add L2 cache-controller node Add the missing L2 cache-controller node, and link the CPU node to it. This will allow migration to the generic l2c OF initialization. The L2 cache is an ARM L2C-310 (r3p1-150rel0), of size 256 KiB (32 KiB x 8 ways). Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7740.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi index e14cb1438216..7676646f7085 100644 --- a/arch/arm/boot/dts/r8a7740.dtsi +++ b/arch/arm/boot/dts/r8a7740.dtsi @@ -26,6 +26,7 @@ reg = <0x0>; clock-frequency = <800000000>; power-domains = <&pd_a3sm>; + next-level-cache = <&L2>; }; }; @@ -37,6 +38,18 @@ <0xc2000000 0x1000>; }; + L2: cache-controller { + compatible = "arm,pl310-cache"; + reg = <0xf0100000 0x1000>; + interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_a3sm>; + arm,data-latency = <3 3 3>; + arm,tag-latency = <2 2 2>; + arm,shared-override; + cache-unified; + cache-level = <2>; + }; + dbsc3: memory-controller@fe400000 { compatible = "renesas,dbsc3-r8a7740"; reg = <0xfe400000 0x400>; -- cgit v1.2.3 From c8d9fdbe2d648caaa510d45dc13eba2e9957140b Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 23 Nov 2015 14:56:00 +0100 Subject: ARM: shmobile: sh73a0 dtsi: Add L2 cache-controller node Add the missing L2 cache-controller node, and link the CPU nodes to it. This will allow migration to the generic l2c OF initialization. The L2 cache is an ARM L2C-310 (r3p1), of size 512 KiB (64 KiB x 8 ways). Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/sh73a0.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index ff7c8f298f30..319551f0fcdb 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -28,6 +28,7 @@ reg = <0>; clock-frequency = <1196000000>; power-domains = <&pd_a2sl>; + next-level-cache = <&L2>; }; cpu@1 { device_type = "cpu"; @@ -35,6 +36,7 @@ reg = <1>; clock-frequency = <1196000000>; power-domains = <&pd_a2sl>; + next-level-cache = <&L2>; }; }; @@ -53,6 +55,18 @@ <0xf0000100 0x100>; }; + L2: cache-controller { + compatible = "arm,pl310-cache"; + reg = <0xf0100000 0x1000>; + interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_a3sm>; + arm,data-latency = <3 3 3>; + arm,tag-latency = <2 2 2>; + arm,shared-override; + cache-unified; + cache-level = <2>; + }; + sbsc2: memory-controller@fb400000 { compatible = "renesas,sbsc-sh73a0"; reg = <0xfb400000 0x400>; -- cgit v1.2.3 From c2cb616129ba28a530eb286c1e9c5bf9da042924 Mon Sep 17 00:00:00 2001 From: Zain Wang Date: Wed, 25 Nov 2015 13:43:33 +0800 Subject: ARM: dts: rockchip: Add Crypto node for rk3288 Add Crypto node for rk3288 including crypto controller and dma clk. Signed-off-by: Zain Wang Tested-by: Heiko Stuebner Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 2040a1b0cf76..6d6cc16669b2 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -781,6 +781,18 @@ status = "disabled"; }; + crypto: cypto-controller@ff8a0000 { + compatible = "rockchip,rk3288-crypto"; + reg = <0xff8a0000 0x4000>; + interrupts = ; + clocks = <&cru ACLK_CRYPTO>, <&cru HCLK_CRYPTO>, + <&cru SCLK_CRYPTO>, <&cru ACLK_DMAC1>; + clock-names = "aclk", "hclk", "sclk", "apb_pclk"; + resets = <&cru SRST_CRYPTO>; + reset-names = "crypto-rst"; + status = "okay"; + }; + vopb: vop@ff930000 { compatible = "rockchip,rk3288-vop"; reg = <0xff930000 0x19c>; -- cgit v1.2.3 From a94eaa98d402d6337392c040fe29f5fa50e859db Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 16 Nov 2015 19:09:47 +0800 Subject: arm: dts: berlin2q: add watchdog nodes The Marvell Berlin BG2Q has 3 watchdogs which are compatible with the snps,dw-wdt driver sit in the sysmgr domain. This patch adds the corresponding device tree nodes. Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2q.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index 155430a2d747..4241a615a74f 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -506,6 +506,29 @@ ranges = <0 0xfc0000 0x10000>; interrupt-parent = <&sic>; + wdt0: watchdog@1000 { + compatible = "snps,dw-wdt"; + reg = <0x1000 0x100>; + clocks = <&refclk>; + interrupts = <0>; + }; + + wdt1: watchdog@2000 { + compatible = "snps,dw-wdt"; + reg = <0x2000 0x100>; + clocks = <&refclk>; + interrupts = <1>; + status = "disabled"; + }; + + wdt2: watchdog@3000 { + compatible = "snps,dw-wdt"; + reg = <0x3000 0x100>; + clocks = <&refclk>; + interrupts = <2>; + status = "disabled"; + }; + sm_gpio1: gpio@5000 { compatible = "snps,dw-apb-gpio"; reg = <0x5000 0x400>; -- cgit v1.2.3 From 096d74d7be2ed32f1d5904bb57caf60b1f10e713 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 16 Nov 2015 19:09:48 +0800 Subject: arm: dts: berlin2cd: add watchdog nodes The Marvell Berlin BG2CD has 3 watchdogs which are compatible with the snps,dw-wdt driver sit in the sysmgr domain. This patch adds the corresponding device tree nodes. NOTE: although BG2CD doesn't have a HW sysmgr, but the sysmgr domain exists. Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2cd.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/berlin2cd.dtsi index b16df157214d..6d06b6118d83 100644 --- a/arch/arm/boot/dts/berlin2cd.dtsi +++ b/arch/arm/boot/dts/berlin2cd.dtsi @@ -396,6 +396,29 @@ ranges = <0 0xfc0000 0x10000>; interrupt-parent = <&sic>; + wdt0: watchdog@1000 { + compatible = "snps,dw-wdt"; + reg = <0x1000 0x100>; + clocks = <&refclk>; + interrupts = <0>; + }; + + wdt1: watchdog@2000 { + compatible = "snps,dw-wdt"; + reg = <0x2000 0x100>; + clocks = <&refclk>; + interrupts = <1>; + status = "disabled"; + }; + + wdt2: watchdog@3000 { + compatible = "snps,dw-wdt"; + reg = <0x3000 0x100>; + clocks = <&refclk>; + interrupts = <2>; + status = "disabled"; + }; + sm_gpio1: gpio@5000 { compatible = "snps,dw-apb-gpio"; reg = <0x5000 0x400>; -- cgit v1.2.3 From 4b6c390b63ee4b1c9a4c53885fea01c1c4e0d87b Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 16 Nov 2015 19:09:49 +0800 Subject: arm: dts: berlin2: add watchdog nodes The Marvell Berlin BG2 has 3 watchdogs which are compatible with the snps,dw-wdt driver sit in the sysmgr domain. This patch adds the corresponding device tree nodes. Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi index eaadac3bdd44..ae81009741ff 100644 --- a/arch/arm/boot/dts/berlin2.dtsi +++ b/arch/arm/boot/dts/berlin2.dtsi @@ -435,6 +435,29 @@ ranges = <0 0xfc0000 0x10000>; interrupt-parent = <&sic>; + wdt0: watchdog@1000 { + compatible = "snps,dw-wdt"; + reg = <0x1000 0x100>; + clocks = <&refclk>; + interrupts = <0>; + }; + + wdt1: watchdog@2000 { + compatible = "snps,dw-wdt"; + reg = <0x2000 0x100>; + clocks = <&refclk>; + interrupts = <1>; + status = "disabled"; + }; + + wdt2: watchdog@3000 { + compatible = "snps,dw-wdt"; + reg = <0x3000 0x100>; + clocks = <&refclk>; + interrupts = <2>; + status = "disabled"; + }; + sm_gpio1: gpio@5000 { compatible = "snps,dw-apb-gpio"; reg = <0x5000 0x400>; -- cgit v1.2.3 From 0cea5f714c7764ca254b0528d0fc3d97023cfafd Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Sat, 28 Nov 2015 12:14:05 +0100 Subject: ARM: dt: mvebu: ix4-300d: remove whole flash partition Current NAND node has an additional flash partition for the whole flash overlapping with real partitions. Remove this partition as the whole flash is already represented by the NAND device itself. Signed-off-by: Sebastian Hesselbarth Acked-by: Andrew Lunn Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 58b500873bfd..30a0a6eac645 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -183,11 +183,6 @@ label = "boot"; reg = <0xE00000 0x3F200000>; }; - - partition@flash { - label = "flash"; - reg = <0x0 0x40000000>; - }; }; }; }; -- cgit v1.2.3 From efc1aaa53e6a9ac26865c02e05fe1e9b2ed24715 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Sat, 28 Nov 2015 12:14:06 +0100 Subject: ARM: dt: mvebu: ix4-300d: move partitions to partition sub-node NAND flash partitions should be part of a partitions sub-node not the flash node itself. Move the partitions which will also allow different bootloaders get rid of the stock partitions easily by removing the partitions node. Signed-off-by: Sebastian Hesselbarth Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts | 67 +++++++++++++------------ 1 file changed, 36 insertions(+), 31 deletions(-) diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 30a0a6eac645..76781fd18624 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -151,37 +151,42 @@ marvell,nand-enable-arbiter; nand-on-flash-bbt; - partition@0 { - label = "u-boot"; - reg = <0x0000000 0xe0000>; - read-only; - }; - - partition@e0000 { - label = "u-boot-env"; - reg = <0xe0000 0x20000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env2"; - reg = <0x100000 0x20000>; - read-only; - }; - - partition@120000 { - label = "zImage"; - reg = <0x120000 0x400000>; - }; - - partition@520000 { - label = "initrd"; - reg = <0x520000 0x400000>; - }; - - partition@xE00000 { - label = "boot"; - reg = <0xE00000 0x3F200000>; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0xe0000>; + read-only; + }; + + partition@e0000 { + label = "u-boot-env"; + reg = <0xe0000 0x20000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env2"; + reg = <0x100000 0x20000>; + read-only; + }; + + partition@120000 { + label = "zImage"; + reg = <0x120000 0x400000>; + }; + + partition@520000 { + label = "initrd"; + reg = <0x520000 0x400000>; + }; + + partition@xE00000 { + label = "boot"; + reg = <0xE00000 0x3F200000>; + }; }; }; }; -- cgit v1.2.3 From 4627629bbb675665e902ad76ab96ac1ee5d17fd8 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Sat, 28 Nov 2015 12:14:07 +0100 Subject: ARM: dt: mvebu: ix4-300d: Cleanup NAND partition ranges Prefix all partition reg properties to 32-bit to ease readability. While at it, also remove a stale x in front of boot partition offset and make some upper-case hex numbers lower-case. Signed-off-by: Sebastian Hesselbarth Acked-by: Andrew Lunn Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 76781fd18624..13cf69a8d0fb 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -157,35 +157,35 @@ partition@0 { label = "u-boot"; - reg = <0x0000000 0xe0000>; + reg = <0x00000000 0x000e0000>; read-only; }; partition@e0000 { label = "u-boot-env"; - reg = <0xe0000 0x20000>; + reg = <0x000e0000 0x00020000>; read-only; }; partition@100000 { label = "u-boot-env2"; - reg = <0x100000 0x20000>; + reg = <0x00100000 0x00020000>; read-only; }; partition@120000 { label = "zImage"; - reg = <0x120000 0x400000>; + reg = <0x00120000 0x00400000>; }; partition@520000 { label = "initrd"; - reg = <0x520000 0x400000>; + reg = <0x00520000 0x00400000>; }; - partition@xE00000 { + partition@e00000 { label = "boot"; - reg = <0xE00000 0x3F200000>; + reg = <0x00e00000 0x3f200000>; }; }; }; -- cgit v1.2.3 From fc63efdf4bbcc23968bc71cfbc7dedf56c5ff01e Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:39 -0300 Subject: pinctrl: Move am4372 and dra7 macros to the the SoC header files The header file defines a set of macros for different SoCs families that falls under the OMAP sub-arch, that allow to define the padconf register physical address instead of the register offset from the padconf base. But the am43xx and dra7xx SoCs families have their own pinctrl header file so the DTS using these SoCs aren't able to use the AM4372_IOPAD() and DRA7XX_CORE_IOPAD() macros since is not included. Move the macros to the correct header files so can be used by the DTS. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- include/dt-bindings/pinctrl/am43xx.h | 6 ++++++ include/dt-bindings/pinctrl/dra.h | 6 ++++++ include/dt-bindings/pinctrl/omap.h | 2 -- 3 files changed, 12 insertions(+), 2 deletions(-) diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h index 774dc1e843c5..344bd1eb3386 100644 --- a/include/dt-bindings/pinctrl/am43xx.h +++ b/include/dt-bindings/pinctrl/am43xx.h @@ -31,5 +31,11 @@ #define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP) #define PIN_INPUT_PULLDOWN (INPUT_EN) +/* + * Macro to allow using the absolute physical address instead of the + * padconf registers instead of the offset from padconf base. + */ +#define AM4372_IOPAD(pa, val) (((pa) & 0xffff) - 0x0800) (val) + #endif diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h index 4379e29f0460..5c75e80915fc 100644 --- a/include/dt-bindings/pinctrl/dra.h +++ b/include/dt-bindings/pinctrl/dra.h @@ -67,5 +67,11 @@ #define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP) #define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN) +/* + * Macro to allow using the absolute physical address instead of the + * padconf registers instead of the offset from padconf base. + */ +#define DRA7XX_CORE_IOPAD(pa, val) (((pa) & 0xffff) - 0x3400) (val) + #endif diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h index 13949259705a..8100de13851c 100644 --- a/include/dt-bindings/pinctrl/omap.h +++ b/include/dt-bindings/pinctrl/omap.h @@ -63,8 +63,6 @@ #define OMAP3_WKUP_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2a00) (val) #define DM816X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) #define AM33XX_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) -#define AM4372_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) -#define DRA7XX_CORE_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x3400) (val) /* * Macros to allow using the offset from the padconf physical address -- cgit v1.2.3 From 22a1cd8a788f78375c1fe42418a31ee732de171a Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:40 -0300 Subject: ARM: dts: am335x-baltos-ir5221: Remove leftover pinctrl lines When the Device Tree source file got merged, some commented pinctrl lines were left in the file. These are already defined so seems to be a cleanup that was missed. Delete the unneeded lines from the file. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-baltos-ir5221.dts | 4 ---- 1 file changed, 4 deletions(-) diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts index 7d36601697da..3b42635bc995 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts @@ -109,8 +109,6 @@ pinctrl-single,pins = < 0x180 0x28 /* uart1_rxd, INPUT | MODE0 */ 0x184 0x28 /* uart1_txd, INPUT | MODE0 */ - /*0x178 0x28*/ /* uart1_ctsn, INPUT | MODE0 */ - /*0x17c 0x08*/ /* uart1_rtsn, OUTPUT | MODE0 */ 0x178 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn, INPUT | MODE0 */ 0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn, OUTPUT | MODE0 */ 0x0e0 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.gpio2[22] DTR */ @@ -124,8 +122,6 @@ pinctrl-single,pins = < 0x150 0x29 /* spi0_sclk.uart2_rxd_mux3, INPUT | MODE1 */ 0x154 0x09 /* spi0_d0.uart2_txd_mux3, OUTPUT | MODE1 */ - /*0x188 0x2a*/ /* i2c0_sda.uart2_ctsn_mux0, INPUT | MODE2 */ - /*0x18c 0x2a*/ /* i2c0_scl.uart2_rtsn_mux0, INPUT | MODE2 */ 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* i2c0_sda.uart2_ctsn_mux0 */ 0x18c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* i2c0_scl.uart2_rtsn_mux0 */ 0x030 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.gpio1[12] DTR */ -- cgit v1.2.3 From a0f6ada23f2bd40bd37ddda78a23effd9f3db0d9 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:41 -0300 Subject: ARM: dts: am335x-baltos-ir5221: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Also, use the mux defines instead of magic numbers for the padconf values when defining the pinctrl lines to make it more readable. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-baltos-ir5221.dts | 182 ++++++++++++++--------------- 1 file changed, 91 insertions(+), 91 deletions(-) diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts index 3b42635bc995..ded1eb64ea52 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts @@ -56,171 +56,171 @@ &am33xx_pinmux { mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x020 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad8.mmc1_dat0_mux0 */ - 0x024 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad9.mmc1_dat1_mux0 */ - 0x028 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad10.mmc1_dat2_mux0 */ - 0x02c (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad11.mmc1_dat3_mux0 */ - 0x080 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk_mux0 */ - 0x084 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd_mux0 */ - 0x1e4 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu0.gpio3[7] */ + AM33XX_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad8.mmc1_dat0_mux0 */ + AM33XX_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad9.mmc1_dat1_mux0 */ + AM33XX_IOPAD(0x828, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad10.mmc1_dat2_mux0 */ + AM33XX_IOPAD(0x82c, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad11.mmc1_dat3_mux0 */ + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk_mux0 */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd_mux0 */ + AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLUP | MUX_MODE7) /* emu0.gpio3[7] */ >; }; wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0x1e8 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ + AM33XX_IOPAD(0x9e8, PIN_OUTPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ >; }; tps65910_pins: pinmux_tps65910_pins { pinctrl-single,pins = < - 0x078 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_ben1.gpio1[28] */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_ben1.gpio1[28] */ >; }; tca6416_pins: pinmux_tca6416_pins { pinctrl-single,pins = < - 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE7) /* xdma_event_intr1.gpio0[20] tca6416 stuff */ + AM33XX_IOPAD(0x9b4, PIN_INPUT_PULLUP | MUX_MODE7) /* xdma_event_intr1.gpio0[20] tca6416 stuff */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x158 0x2a /* spi0_d1.i2c1_sda_mux3, INPUT | MODE2 */ - 0x15c 0x2a /* spi0_cs0.i2c1_scl_mux3, INPUT | MODE2 */ + AM33XX_IOPAD(0x958, PIN_INPUT | MUX_MODE2) /* spi0_d1.i2c1_sda_mux3 */ + AM33XX_IOPAD(0x95c, PIN_INPUT | MUX_MODE2) /* spi0_cs0.i2c1_scl_mux3 */ >; }; dcan1_pins: pinmux_dcan1_pins { pinctrl-single,pins = < - 0x168 0x0a /* uart0_ctsn.dcan1_tx_mux0, OUTPUT | MODE2 */ - 0x16c 0x2a /* uart0_rtsn.dcan1_rx_mux0, INPUT | MODE2 */ + AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.dcan1_tx_mux0 */ + AM33XX_IOPAD(0x96c, PIN_INPUT | MUX_MODE2) /* uart0_rtsn.dcan1_rx_mux0 */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x180 0x28 /* uart1_rxd, INPUT | MODE0 */ - 0x184 0x28 /* uart1_txd, INPUT | MODE0 */ - 0x178 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn, INPUT | MODE0 */ - 0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn, OUTPUT | MODE0 */ - 0x0e0 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.gpio2[22] DTR */ - 0x0e4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.gpio2[23] DSR */ - 0x0e8 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.gpio2[24] DCD */ - 0x0ec (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.gpio2[25] RI */ + AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE0) /* uart1_rxd */ + AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE0) /* uart1_txd */ + AM33XX_IOPAD(0x978, PIN_INPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn, INPUT | MODE0 */ + AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn, OUTPUT | MODE0 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.gpio2[22] DTR */ + AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.gpio2[23] DSR */ + AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.gpio2[24] DCD */ + AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.gpio2[25] RI */ >; }; uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0x150 0x29 /* spi0_sclk.uart2_rxd_mux3, INPUT | MODE1 */ - 0x154 0x09 /* spi0_d0.uart2_txd_mux3, OUTPUT | MODE1 */ - 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* i2c0_sda.uart2_ctsn_mux0 */ - 0x18c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* i2c0_scl.uart2_rtsn_mux0 */ - 0x030 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.gpio1[12] DTR */ - 0x034 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.gpio1[13] DSR */ - 0x038 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.gpio1[14] DCD */ - 0x03c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.gpio1[15] RI */ - - 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18], INPUT_PULLDOWN | MODE7 */ + AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd_mux3 */ + AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd_mux3 */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLDOWN | MUX_MODE7) /* i2c0_sda.uart2_ctsn_mux0 */ + AM33XX_IOPAD(0x98c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* i2c0_scl.uart2_rtsn_mux0 */ + AM33XX_IOPAD(0x830, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.gpio1[12] DTR */ + AM33XX_IOPAD(0x834, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.gpio1[13] DSR */ + AM33XX_IOPAD(0x838, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.gpio1[14] DCD */ + AM33XX_IOPAD(0x83c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.gpio1[15] RI */ + + AM33XX_IOPAD(0x9a0, PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18], INPUT_PULLDOWN | MODE7 */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_tx_en.rmii1_txen */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii1_refclk */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_tx_en.rmii1_txen */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii1_refclk */ /* Slave 2 */ - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ - 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ - 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ - 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ + AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ + AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ + AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* Slave 2 reset value*/ - 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x840, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x848, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x84c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x850, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x854, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; nandflash_pins_s0: nandflash_pins_s0 { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; }; -- cgit v1.2.3 From e03b2a26d6bf93d1631aa36985892877986ee7b9 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:42 -0300 Subject: ARM: dts: am335x-bone-common: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-bone-common.dtsi | 104 +++++++++++++++--------------- 1 file changed, 52 insertions(+), 52 deletions(-) diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 5d370d54bd30..0cc150b87b86 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -67,112 +67,112 @@ user_leds_s0: user_leds_s0 { pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ - 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_IOPAD(0x860, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ >; }; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0x178 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ - 0x17c (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; clkout2_pin: pinmux_clkout2_pin { pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ - 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ - 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ - 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ - 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ >; }; emmc_pins: pinmux_emmc_pins { pinctrl-single,pins = < - 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ - 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ - 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ - 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ - 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ >; }; }; -- cgit v1.2.3 From f5ea9398f23207645d7e821ad62b29c6701837c8 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:43 -0300 Subject: ARM: dts: am335x-bonegreen: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-bonegreen.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts index 0f65bdaaa583..dce3c8657e04 100644 --- a/arch/arm/boot/dts/am335x-bonegreen.dts +++ b/arch/arm/boot/dts/am335x-bonegreen.dts @@ -36,8 +36,8 @@ &am33xx_pinmux { uart2_pins: uart2_pins { pinctrl-single,pins = < - 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ - 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ + AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ + AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ >; }; }; -- cgit v1.2.3 From d5d4dc17309af16faa556e44f94714a66fc4f913 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:44 -0300 Subject: ARM: dts: am335x-chiliboard: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-chiliboard.dts | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/am335x-chiliboard.dts b/arch/arm/boot/dts/am335x-chiliboard.dts index 310da20a8aa7..15d47ab28865 100644 --- a/arch/arm/boot/dts/am335x-chiliboard.dts +++ b/arch/arm/boot/dts/am335x-chiliboard.dts @@ -37,26 +37,26 @@ &am33xx_pinmux { usb1_drvvbus: usb1_drvvbus { pinctrl-single,pins = < - 0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* usb1_drvvbus.usb1_drvvbus */ + AM33XX_IOPAD(0xa34, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* usb1_drvvbus.usb1_drvvbus */ >; }; sd_pins: pinmux_sd_card { pinctrl-single,pins = < - 0xf0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0xf4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0xf8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0xfc (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x900, PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x904, PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; led_gpio_pins: led_gpio_pins { pinctrl-single,pins = < - 0x1e4 (PIN_OUTPUT | MUX_MODE7) /* emu0.gpio3_7 */ - 0x1e8 (PIN_OUTPUT | MUX_MODE7) /* emu1.gpio3_8 */ + AM33XX_IOPAD(0x9e4, PIN_OUTPUT | MUX_MODE7) /* emu0.gpio3_7 */ + AM33XX_IOPAD(0x9e8, PIN_OUTPUT | MUX_MODE7) /* emu1.gpio3_8 */ >; }; }; -- cgit v1.2.3 From 9d945f89beb1322b6a1583abe2b840627aa2e611 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:45 -0300 Subject: ARM: dts: am335x-chilisom: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-chilisom.dtsi | 80 +++++++++++++++++----------------- 1 file changed, 40 insertions(+), 40 deletions(-) diff --git a/arch/arm/boot/dts/am335x-chilisom.dtsi b/arch/arm/boot/dts/am335x-chilisom.dtsi index 7e9a34dffe21..857d9894103a 100644 --- a/arch/arm/boot/dts/am335x-chilisom.dtsi +++ b/arch/arm/boot/dts/am335x-chilisom.dtsi @@ -29,81 +29,81 @@ i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ - 0x13c (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii_ref_clk */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii_ref_clk */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* mdio_data.mdio_data */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_clk.mdio_clk */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; nandflash_pins: nandflash_pins { pinctrl-single,pins = < - 0x00 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x04 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x08 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0x0c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; }; -- cgit v1.2.3 From 46bd10c828fe03e45c1167de6be4ab7c5a479aa9 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:46 -0300 Subject: ARM: dts: am335x-evm: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Also, use the mux defines instead of magic numbers for the padconf values when defining the pinctrl lines to make it more readable. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-evm.dts | 220 +++++++++++++++++++-------------------- 1 file changed, 110 insertions(+), 110 deletions(-) diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index d9d00ab863a2..4caf074063fe 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -168,215 +168,215 @@ matrix_keypad_s0: matrix_keypad_s0 { pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */ >; }; volume_keys_s0: volume_keys_s0 { pinctrl-single,pins = < - 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */ - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */ + AM33XX_IOPAD(0x950, PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */ + AM33XX_IOPAD(0x954, PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */ >; }; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ - 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ + AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ - 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ - 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ - 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + AM33XX_IOPAD(0x97C, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ >; }; clkout2_pin: pinmux_clkout2_pin { pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ >; }; nandflash_pins_s0: nandflash_pins_s0 { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; ecap0_pins: backlight_pins { pinctrl-single,pins = < - 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + AM33XX_IOPAD(0x964, MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; mmc3_pins: pinmux_mmc3_pins { pinctrl-single,pins = < - 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */ - 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */ - 0x4C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */ - 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */ - 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */ - 0x8C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x848, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x84c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */ + AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */ >; }; wlan_pins: pinmux_wlan_pins { pinctrl-single,pins = < - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 */ - 0x19C (PIN_INPUT | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */ - 0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 */ + AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 */ + AM33XX_IOPAD(0x99c, PIN_INPUT | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */ + AM33XX_IOPAD(0x9ac, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 */ >; }; lcd_pins_s0: lcd_pins_s0 { pinctrl-single,pins = < - 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ - 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ - 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ - 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ - 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ - 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ - 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ - 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ - 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ - 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ - 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ - 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ - 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ - 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ - 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ - 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ - 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ - 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ - 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ - 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + AM33XX_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ >; }; mcasp1_pins: mcasp1_pins { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ - 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + AM33XX_IOPAD(0x908, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ >; }; mcasp1_pins_sleep: mcasp1_pins_sleep { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; dcan1_pins_default: dcan1_pins_default { pinctrl-single,pins = < - 0x168 (PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ - 0x16c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ + AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ + AM33XX_IOPAD(0x96c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ >; }; }; -- cgit v1.2.3 From 06e08fda184de0a57ffded98424d60eb7316b446 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:47 -0300 Subject: ARM: dts: am335x-evmsk: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Also, use the mux defines instead of magic numbers for the padconf values when defining the pinctrl lines to make it more readable. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-evmsk.dts | 278 ++++++++++++++++++------------------- 1 file changed, 139 insertions(+), 139 deletions(-) diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 89442e98a837..9609668919f1 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -204,234 +204,234 @@ lcd_pins_default: lcd_pins_default { pinctrl-single,pins = < - 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ - 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ - 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ - 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ - 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ - 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ - 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ - 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ - 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ - 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ - 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ - 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ - 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ - 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ - 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ - 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ - 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ - 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ - 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ - 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + AM33XX_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ >; }; lcd_pins_sleep: lcd_pins_sleep { pinctrl-single,pins = < - 0x20 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad8.lcd_data23 */ - 0x24 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad9.lcd_data22 */ - 0x28 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.lcd_data21 */ - 0x2c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.lcd_data20 */ - 0x30 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.lcd_data19 */ - 0x34 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.lcd_data18 */ - 0x38 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.lcd_data17 */ - 0x3c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.lcd_data16 */ - 0xa0 (PULL_DISABLE | MUX_MODE7) /* lcd_data0.lcd_data0 */ - 0xa4 (PULL_DISABLE | MUX_MODE7) /* lcd_data1.lcd_data1 */ - 0xa8 (PULL_DISABLE | MUX_MODE7) /* lcd_data2.lcd_data2 */ - 0xac (PULL_DISABLE | MUX_MODE7) /* lcd_data3.lcd_data3 */ - 0xb0 (PULL_DISABLE | MUX_MODE7) /* lcd_data4.lcd_data4 */ - 0xb4 (PULL_DISABLE | MUX_MODE7) /* lcd_data5.lcd_data5 */ - 0xb8 (PULL_DISABLE | MUX_MODE7) /* lcd_data6.lcd_data6 */ - 0xbc (PULL_DISABLE | MUX_MODE7) /* lcd_data7.lcd_data7 */ - 0xc0 (PULL_DISABLE | MUX_MODE7) /* lcd_data8.lcd_data8 */ - 0xc4 (PULL_DISABLE | MUX_MODE7) /* lcd_data9.lcd_data9 */ - 0xc8 (PULL_DISABLE | MUX_MODE7) /* lcd_data10.lcd_data10 */ - 0xcc (PULL_DISABLE | MUX_MODE7) /* lcd_data11.lcd_data11 */ - 0xd0 (PULL_DISABLE | MUX_MODE7) /* lcd_data12.lcd_data12 */ - 0xd4 (PULL_DISABLE | MUX_MODE7) /* lcd_data13.lcd_data13 */ - 0xd8 (PULL_DISABLE | MUX_MODE7) /* lcd_data14.lcd_data14 */ - 0xdc (PULL_DISABLE | MUX_MODE7) /* lcd_data15.lcd_data15 */ - 0xe0 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.lcd_vsync */ - 0xe4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.lcd_hsync */ - 0xe8 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.lcd_pclk */ - 0xec (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x820, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad8.lcd_data23 */ + AM33XX_IOPAD(0x824, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad9.lcd_data22 */ + AM33XX_IOPAD(0x828, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.lcd_data21 */ + AM33XX_IOPAD(0x82c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.lcd_data20 */ + AM33XX_IOPAD(0x830, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.lcd_data19 */ + AM33XX_IOPAD(0x834, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.lcd_data18 */ + AM33XX_IOPAD(0x838, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.lcd_data17 */ + AM33XX_IOPAD(0x83c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.lcd_data16 */ + AM33XX_IOPAD(0x8a0, PULL_DISABLE | MUX_MODE7) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PULL_DISABLE | MUX_MODE7) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PULL_DISABLE | MUX_MODE7) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PULL_DISABLE | MUX_MODE7) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PULL_DISABLE | MUX_MODE7) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PULL_DISABLE | MUX_MODE7) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PULL_DISABLE | MUX_MODE7) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PULL_DISABLE | MUX_MODE7) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PULL_DISABLE | MUX_MODE7) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PULL_DISABLE | MUX_MODE7) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PULL_DISABLE | MUX_MODE7) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PULL_DISABLE | MUX_MODE7) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PULL_DISABLE | MUX_MODE7) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PULL_DISABLE | MUX_MODE7) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PULL_DISABLE | MUX_MODE7) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PULL_DISABLE | MUX_MODE7) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.lcd_ac_bias_en */ >; }; user_leds_s0: user_leds_s0 { pinctrl-single,pins = < - 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ - 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ - 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ - 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ + AM33XX_IOPAD(0x810, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ + AM33XX_IOPAD(0x814, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ + AM33XX_IOPAD(0x818, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ + AM33XX_IOPAD(0x81c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ >; }; gpio_keys_s0: gpio_keys_s0 { pinctrl-single,pins = < - 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ - 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */ - 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ - 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ + AM33XX_IOPAD(0x894, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ + AM33XX_IOPAD(0x890, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ + AM33XX_IOPAD(0x89c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ >; }; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; clkout2_pin: pinmux_clkout2_pin { pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ >; }; ecap2_pins: backlight_pins { pinctrl-single,pins = < - 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */ + AM33XX_IOPAD(0x99c, MUX_MODE4) /* mcasp0_ahclkr.ecap2_in_pwm2_out */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ /* Slave 2 */ - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ - 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ - 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ - 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ + AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ + AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ + AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) /* Slave 2 reset value*/ - 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x840, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x848, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x84c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x850, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x854, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; mcasp1_pins: mcasp1_pins { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ - 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + AM33XX_IOPAD(0x908, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ >; }; mcasp1_pins_sleep: mcasp1_pins_sleep { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ - 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ - 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ - 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ - 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ - 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ >; }; wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */ >; }; }; -- cgit v1.2.3 From 9b0aebddd0ad585e4f6f3a2b021293cfcada8e84 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:48 -0300 Subject: ARM: dts: am335x-lxm: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-lxm.dts | 120 +++++++++++++++++++-------------------- 1 file changed, 60 insertions(+), 60 deletions(-) diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts index 5c5667a3624d..d97b0efa43f3 100644 --- a/arch/arm/boot/dts/am335x-lxm.dts +++ b/arch/arm/boot/dts/am335x-lxm.dts @@ -46,109 +46,109 @@ &am33xx_pinmux { mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */ - 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */ - 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */ - 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */ - 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */ - 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */ >; }; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */ /* Slave 2 */ - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */ - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */ - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */ - 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */ - 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */ - 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */ - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */ + AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */ + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */ + AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */ - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */ - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */ + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */ + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */ /* Slave 2 reset value*/ - 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */ - 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */ - 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */ - 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */ - 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */ - 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */ - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */ + AM33XX_IOPAD(0x840, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */ + AM33XX_IOPAD(0x850, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */ + AM33XX_IOPAD(0x854, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */ + AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */ >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; emmc_pins: pinmux_emmc_pins { pinctrl-single,pins = < - 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ - 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ - 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ - 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ - 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; }; -- cgit v1.2.3 From 4c12b9e1e513bc19ea9d7b011265c0f20dc57e22 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:49 -0300 Subject: ARM: dts: am335x-nano: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-nano.dts | 140 +++++++++++++++++++------------------- 1 file changed, 70 insertions(+), 70 deletions(-) diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts index 5ed4ca6eaf55..f313999c503e 100644 --- a/arch/arm/boot/dts/am335x-nano.dts +++ b/arch/arm/boot/dts/am335x-nano.dts @@ -41,121 +41,121 @@ misc_pins: misc_pins { pinctrl-single,pins = < - 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */ + AM33XX_IOPAD(0x95c, PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */ >; }; gpmc_pins: gpmc_pins { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */ - 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */ - 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */ - 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */ - 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */ - 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */ - 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */ - 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */ - - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */ - 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */ - 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */ - - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */ - - 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */ - 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */ - 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */ - - 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */ - 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */ - 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */ + AM33XX_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */ + AM33XX_IOPAD(0x828, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */ + AM33XX_IOPAD(0x82c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */ + AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */ + AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */ + AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */ + AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */ + + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x880, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */ + AM33XX_IOPAD(0x884, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */ + AM33XX_IOPAD(0x888, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */ + + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */ + + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */ + + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */ >; }; i2c0_pins: i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; uart0_pins: uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; uart1_pins: uart1_pins { pinctrl-single,pins = < - 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */ - 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */ - 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ - 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */ + AM33XX_IOPAD(0x978, PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */ + AM33XX_IOPAD(0x97c, PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */ + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + AM33XX_IOPAD(0x984, PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */ >; }; uart2_pins: uart2_pins { pinctrl-single,pins = < - 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */ - 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */ - 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ - 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ + AM33XX_IOPAD(0x8c0, PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */ + AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ + AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ >; }; uart3_pins: uart3_pins { pinctrl-single,pins = < - 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */ - 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */ - 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */ - 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */ + AM33XX_IOPAD(0x8c8, PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */ + AM33XX_IOPAD(0x964, PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */ >; }; uart4_pins: uart4_pins { pinctrl-single,pins = < - 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */ - 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */ - 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */ - 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */ + AM33XX_IOPAD(0x8d0, PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */ + AM33XX_IOPAD(0x968, PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */ + AM33XX_IOPAD(0x96c, PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */ >; }; uart5_pins: uart5_pins { pinctrl-single,pins = < - 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */ - 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */ + AM33XX_IOPAD(0x8d8, PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */ + AM33XX_IOPAD(0x944, PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */ >; }; mmc1_pins: mmc1_pins { pinctrl-single,pins = < - 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ - 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ + AM33XX_IOPAD(0x9a0, PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */ >; }; }; -- cgit v1.2.3 From 3eb9d92cd3e96f8a5a6f3eee90874ac5369f045d Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:50 -0300 Subject: ARM: dts: am335x-pepper: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-pepper.dts | 200 ++++++++++++++++++------------------ 1 file changed, 100 insertions(+), 100 deletions(-) diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts index 7106114c7464..f9d7239ebdaf 100644 --- a/arch/arm/boot/dts/am335x-pepper.dts +++ b/arch/arm/boot/dts/am335x-pepper.dts @@ -93,14 +93,14 @@ &am33xx_pinmux { i2c0_pins: pinmux_i2c0 { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c1_pins: pinmux_i2c1 { pinctrl-single,pins = < - 0x10C (PIN_INPUT_PULLUP | MUX_MODE3) /* mii1_crs,i2c1_sda */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE3) /* mii1_rxerr,i2c1_scl */ + AM33XX_IOPAD(0x90C, PIN_INPUT_PULLUP | MUX_MODE3) /* mii1_crs,i2c1_sda */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE3) /* mii1_rxerr,i2c1_scl */ >; }; }; @@ -130,7 +130,7 @@ &am33xx_pinmux { accel_pins: pinmux_accel { pinctrl-single,pins = < - 0x98 (PIN_INPUT | MUX_MODE7) /* gpmc_wen.gpio2_4 */ + AM33XX_IOPAD(0x898, PIN_INPUT | MUX_MODE7) /* gpmc_wen.gpio2_4 */ >; }; }; @@ -177,12 +177,12 @@ &am33xx_pinmux { audio_pins: pinmux_audio { pinctrl-single,pins = < - 0x1AC (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ - 0x194 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ - 0x190 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ - 0x198 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr0.mcasp0_axr0 */ - 0x1A8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr1.mcasp0_axr1 */ - 0x40 (PIN_OUTPUT | MUX_MODE7) /* gpmc_a0.gpio1_16 */ + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ + AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr0.mcasp0_axr0 */ + AM33XX_IOPAD(0x9a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr1.mcasp0_axr1 */ + AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE7) /* gpmc_a0.gpio1_16 */ >; }; }; @@ -228,36 +228,36 @@ &am33xx_pinmux { lcd_pins: pinmux_lcd { pinctrl-single,pins = < - 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ - 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ - 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ - 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ - 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ - 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ - 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ - 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ - 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data16 */ - 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data17 */ - 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data18 */ - 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data19 */ - 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data20 */ - 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data21 */ - 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data22 */ - 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data23 */ - 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ - 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ - 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ - 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data16 */ + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data17 */ + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data18 */ + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data19 */ + AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data20 */ + AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data21 */ + AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data22 */ + AM33XX_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data23 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ /* Display Enable */ - 0x6c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a11.gpio1_27 */ + AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a11.gpio1_27 */ >; }; }; @@ -291,29 +291,29 @@ &am33xx_pinmux { ethernet_pins: pinmux_ethernet { pinctrl-single,pins = < - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ - 0x134 (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd3.rgmii1_rxd3 */ - 0x138 (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd2.rgmii1_rxd2 */ - 0x13c (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd3.rgmii1_rxd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd2.rgmii1_rxd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ /* ethernet interrupt */ - 0x144 (PIN_INPUT_PULLUP | MUX_MODE7) /* rmii2_refclk.gpio0_29 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLUP | MUX_MODE7) /* rmii2_refclk.gpio0_29 */ /* ethernet PHY nReset */ - 0x108 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* mii1_col.gpio3_0 */ + AM33XX_IOPAD(0x908, PIN_OUTPUT_PULLUP | MUX_MODE7) /* mii1_col.gpio3_0 */ >; }; mdio_pins: pinmux_mdio { pinctrl-single,pins = < - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; }; @@ -363,45 +363,45 @@ &am33xx_pinmux { sd_pins: pinmux_sd_card { pinctrl-single,pins = < - 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; emmc_pins: pinmux_emmc { pinctrl-single,pins = < - 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ - 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ - 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ - 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ - 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ /* EMMC nReset */ - 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ + AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ >; }; wireless_pins: pinmux_wireless { pinctrl-single,pins = < - 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0 */ - 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1 */ - 0x4c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2 */ - 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3 */ - 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ - 0x8c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc1_clk */ + AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0 */ + AM33XX_IOPAD(0x848, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1 */ + AM33XX_IOPAD(0x84c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2 */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3 */ + AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ + AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc1_clk */ /* WLAN nReset */ - 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + AM33XX_IOPAD(0x860, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ /* WLAN nPower down */ - 0x70 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ + AM33XX_IOPAD(0x870, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ /* 32kHz Clock */ - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ >; }; }; @@ -497,10 +497,10 @@ &am33xx_pinmux { spi0_pins: pinmux_spi0 { pinctrl-single,pins = < - 0x150 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_sclk.spi0_sclk */ - 0x15C (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ - 0x154 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d0.spi0_d0 */ - 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ + AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_sclk.spi0_sclk */ + AM33XX_IOPAD(0x95C, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d0.spi0_d0 */ + AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ >; }; }; @@ -538,16 +538,16 @@ &am33xx_pinmux { uart0_pins: pinmux_uart0 { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; uart1_pins: pinmux_uart1 { pinctrl-single,pins = < - 0x178 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ - 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ - 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ - 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + AM33XX_IOPAD(0x97C, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ >; }; }; @@ -590,9 +590,9 @@ usb_pins: pinmux_usb { pinctrl-single,pins = < /* USB0 Over-Current (active low) */ - 0x64 (PIN_INPUT | MUX_MODE7) /* gpmc_a9.gpio1_25 */ + AM33XX_IOPAD(0x864, PIN_INPUT | MUX_MODE7) /* gpmc_a9.gpio1_25 */ /* USB1 Over-Current (active low) */ - 0x68 (PIN_INPUT | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7) /* gpmc_a10.gpio1_26 */ >; }; }; @@ -648,16 +648,16 @@ &am33xx_pinmux { user_leds_pins: pinmux_user_leds { pinctrl-single,pins = < - 0x50 (PIN_OUTPUT | MUX_MODE7) /* gpmc_a4.gpio1_20 */ - 0x54 (PIN_OUTPUT | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE7) /* gpmc_a4.gpio1_20 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* gpmc_a5.gpio1_21 */ >; }; user_buttons_pins: pinmux_user_buttons { pinctrl-single,pins = < - 0x58 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x5C (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a7.gpio1_21 */ - 0x164 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio0_7 */ + AM33XX_IOPAD(0x858, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_IOPAD(0x85C, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a7.gpio1_21 */ + AM33XX_IOPAD(0x964, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio0_7 */ >; }; }; -- cgit v1.2.3 From 9baa78d64452d63f638ee84aa220d99e4954a1d7 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:51 -0300 Subject: ARM: dts: am335x-phycore-som: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-phycore-som.dtsi | 60 +++++++++++++++---------------- 1 file changed, 30 insertions(+), 30 deletions(-) diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi index 2f43e458ea4a..c20ae6c6f6c7 100644 --- a/arch/arm/boot/dts/am335x-phycore-som.dtsi +++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi @@ -56,22 +56,22 @@ &am33xx_pinmux { ethernet0_pins: pinmux_ethernet0 { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ - 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ - 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ - 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + AM33XX_IOPAD(0x914, PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ + AM33XX_IOPAD(0x924, PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ >; }; mdio_pins: pinmux_mdio { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; }; @@ -103,8 +103,8 @@ &am33xx_pinmux { i2c0_pins: pinmux_i2c0 { pinctrl-single,pins = < - 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; }; @@ -137,20 +137,20 @@ &am33xx_pinmux { nandflash_pins: pinmux_nandflash { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; }; @@ -324,10 +324,10 @@ &am33xx_pinmux { spi0_pins: pinmux_spi0 { pinctrl-single,pins = < - 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */ - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */ - 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ - 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + AM33XX_IOPAD(0x950, PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */ + AM33XX_IOPAD(0x954, PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */ + AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ + AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ >; }; }; -- cgit v1.2.3 From bb2fe50e02e5c0daab7695cee8feb9020d8feeae Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:52 -0300 Subject: ARM: dts: am335x-wega: Use AM33XX_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-wega.dtsi | 58 +++++++++++++++++++------------------- 1 file changed, 29 insertions(+), 29 deletions(-) diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi index 2cecb3951e1b..282f6d4b27bc 100644 --- a/arch/arm/boot/dts/am335x-wega.dtsi +++ b/arch/arm/boot/dts/am335x-wega.dtsi @@ -28,8 +28,8 @@ &am33xx_pinmux { dcan1_pins: pinmux_dcan1 { pinctrl-single,pins = < - 0x168 (PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ - 0x16c (PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ + AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ + AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ >; }; }; @@ -44,20 +44,20 @@ &am33xx_pinmux { ethernet1_pins: pinmux_ethernet1 { pinctrl-single,pins = < - 0x40 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a0.mii2_txen */ - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a1.mii2_rxdv */ - 0x48 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a2.mii2_txd3 */ - 0x4c (PIN_OUTPUT | MUX_MODE1) /* gpmc_a3.mii2_txd2 */ - 0x50 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a4.mii2_txd1 */ - 0x54 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a5.mii2_txd0 */ - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a6.mii2_txclk */ - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a7.mii2_rxclk */ - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a8.mii2_rxd3 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a9.mii2_rxd2 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a10.mii2_rxd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a11.mii2_rxd0 */ - 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_wpn.mii2_rxerr */ - 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_ben1.mii2_col */ + AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1) /* gpmc_a0.mii2_txen */ + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a1.mii2_rxdv */ + AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1) /* gpmc_a2.mii2_txd3 */ + AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE1) /* gpmc_a3.mii2_txd2 */ + AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1) /* gpmc_a4.mii2_txd1 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1) /* gpmc_a5.mii2_txd0 */ + AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a6.mii2_txclk */ + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a7.mii2_rxclk */ + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a8.mii2_rxd3 */ + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a9.mii2_rxd2 */ + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a10.mii2_rxd1 */ + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a11.mii2_rxd0 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_wpn.mii2_rxerr */ + AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_ben1.mii2_col */ >; }; }; @@ -79,13 +79,13 @@ &am33xx_pinmux { mmc1_pins: pinmux_mmc1 { pinctrl-single,pins = < - 0x0F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x0F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0x0F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0x0FC (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x160 (PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */ >; }; }; @@ -103,17 +103,17 @@ &am33xx_pinmux { uart0_pins: pinmux_uart0 { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ - 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ - 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ - 0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ >; }; }; -- cgit v1.2.3 From a7efe6ba0c5ae1f3750367f6d6756510afee8c16 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:53 -0300 Subject: ARM: dts: am3517-craneboard: Use OMAP3_CORE1_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am3517-craneboard.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/am3517-craneboard.dts b/arch/arm/boot/dts/am3517-craneboard.dts index 2d40b3f241cd..cb7de1d4e05f 100644 --- a/arch/arm/boot/dts/am3517-craneboard.dts +++ b/arch/arm/boot/dts/am3517-craneboard.dts @@ -77,7 +77,7 @@ &omap3_pmx_core { tps_pins: pinmux_tps_pins { pinctrl-single,pins = < - 0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */ + OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */ >; }; }; -- cgit v1.2.3 From 596bad7dc46c3e2628c724447f73f71a0b76ee25 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:54 -0300 Subject: ARM: dts: am437x-gp-evm: Use AM4372_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-gp-evm.dts | 380 ++++++++++++++++++------------------ 1 file changed, 190 insertions(+), 190 deletions(-) diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index d2450ab0a380..7f00e85eebed 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -154,138 +154,138 @@ i2c0_pins: i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c1_pins: i2c1_pins { pinctrl-single,pins = < - 0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ - 0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ + AM4372_IOPAD(0x95c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + AM4372_IOPAD(0x958, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; ecap0_pins: backlight_pins { pinctrl-single,pins = < - 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + AM4372_IOPAD(0x964, MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ >; }; pixcir_ts_pins: pixcir_ts_pins { pinctrl-single,pins = < - 0x264 (PIN_INPUT_PULLUP | MUX_MODE7) /* spi2_d0.gpio3_22 */ + AM4372_IOPAD(0xa64, PIN_INPUT_PULLUP | MUX_MODE7) /* spi2_d0.gpio3_22 */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_txen */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rxctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd0 */ - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd3 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd2 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ + AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_txen */ + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rxctl */ + AM4372_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd3 */ + AM4372_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd2 */ + AM4372_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd1 */ + AM4372_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd0 */ + AM4372_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd3 */ + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd2 */ + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM4372_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; nand_flash_x8: nand_flash_x8 { pinctrl-single,pins = < - 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM4372_IOPAD(0x800, PIN_INPUT | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM4372_IOPAD(0x804, PIN_INPUT | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM4372_IOPAD(0x808, PIN_INPUT | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM4372_IOPAD(0x80c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM4372_IOPAD(0x810, PIN_INPUT | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM4372_IOPAD(0x814, PIN_INPUT | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM4372_IOPAD(0x818, PIN_INPUT | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM4372_IOPAD(0x81c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM4372_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM4372_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ + AM4372_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM4372_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM4372_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM4372_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM4372_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; dss_pins: dss_pins { pinctrl-single,pins = < - 0x020 (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */ - 0x024 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x028 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x02c (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x030 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x034 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x038 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x03c (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */ - 0x0a0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */ - 0x0a4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0a8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0ac (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0b0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0b4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0b8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0bc (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0c0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0c4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0c8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0cc (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0d4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0d8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0dc (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */ - 0x0e0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */ - 0x0e4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */ - 0x0e8 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */ - 0x0ec (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */ + AM4372_IOPAD(0x820, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */ + AM4372_IOPAD(0x824, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x828, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x82c, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x830, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x834, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x838, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x83c, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */ + AM4372_IOPAD(0x8a0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */ + AM4372_IOPAD(0x8a4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8a8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8ac, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8bc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8cc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8dc, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */ + AM4372_IOPAD(0x8e0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */ + AM4372_IOPAD(0x8e4, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */ + AM4372_IOPAD(0x8e8, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */ + AM4372_IOPAD(0x8ec, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */ >; }; @@ -293,208 +293,208 @@ display_mux_pins: display_mux_pins { pinctrl-single,pins = < /* GPIO 5_8 to select LCD / HDMI */ - 0x238 (PIN_OUTPUT_PULLUP | MUX_MODE7) + AM4372_IOPAD(0xa38, PIN_OUTPUT_PULLUP | MUX_MODE7) >; }; dcan0_default: dcan0_default_pins { pinctrl-single,pins = < - 0x178 (PIN_OUTPUT | MUX_MODE2) /* uart1_ctsn.d_can0_tx */ - 0x17c (PIN_INPUT_PULLUP | MUX_MODE2) /* uart1_rtsn.d_can0_rx */ + AM4372_IOPAD(0x978, PIN_OUTPUT | MUX_MODE2) /* uart1_ctsn.d_can0_tx */ + AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE2) /* uart1_rtsn.d_can0_rx */ >; }; dcan0_sleep: dcan0_sleep_pins { pinctrl-single,pins = < - 0x178 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_ctsn.gpio0_12 */ - 0x17c (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rtsn.gpio0_13 */ + AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_ctsn.gpio0_12 */ + AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rtsn.gpio0_13 */ >; }; dcan1_default: dcan1_default_pins { pinctrl-single,pins = < - 0x180 (PIN_OUTPUT | MUX_MODE2) /* uart1_rxd.d_can1_tx */ - 0x184 (PIN_INPUT_PULLUP | MUX_MODE2) /* uart1_txd.d_can1_rx */ + AM4372_IOPAD(0x980, PIN_OUTPUT | MUX_MODE2) /* uart1_rxd.d_can1_tx */ + AM4372_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2) /* uart1_txd.d_can1_rx */ >; }; dcan1_sleep: dcan1_sleep_pins { pinctrl-single,pins = < - 0x180 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rxd.gpio0_14 */ - 0x184 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_txd.gpio0_15 */ + AM4372_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rxd.gpio0_14 */ + AM4372_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_txd.gpio0_15 */ >; }; vpfe0_pins_default: vpfe0_pins_default { pinctrl-single,pins = < - 0x1B0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_hd mode 0*/ - 0x1B4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_vd mode 0*/ - 0x1C0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_pclk mode 0*/ - 0x1C4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data8 mode 0*/ - 0x1C8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data9 mode 0*/ - 0x208 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data0 mode 0*/ - 0x20C (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data1 mode 0*/ - 0x210 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data2 mode 0*/ - 0x214 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data3 mode 0*/ - 0x218 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data4 mode 0*/ - 0x21C (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data5 mode 0*/ - 0x220 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data6 mode 0*/ - 0x224 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data7 mode 0*/ + AM4372_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_hd mode 0*/ + AM4372_IOPAD(0x9b4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_vd mode 0*/ + AM4372_IOPAD(0x9c0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_pclk mode 0*/ + AM4372_IOPAD(0x9c4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data8 mode 0*/ + AM4372_IOPAD(0x9c8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data9 mode 0*/ + AM4372_IOPAD(0xa08, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data0 mode 0*/ + AM4372_IOPAD(0xa0c, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data1 mode 0*/ + AM4372_IOPAD(0xa10, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data2 mode 0*/ + AM4372_IOPAD(0xa14, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data3 mode 0*/ + AM4372_IOPAD(0xa18, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data4 mode 0*/ + AM4372_IOPAD(0xa1c, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data5 mode 0*/ + AM4372_IOPAD(0xa20, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data6 mode 0*/ + AM4372_IOPAD(0xa24, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data7 mode 0*/ >; }; vpfe0_pins_sleep: vpfe0_pins_sleep { pinctrl-single,pins = < - 0x1B0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_hd mode 0*/ - 0x1B4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_vd mode 0*/ - 0x1C0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_pclk mode 0*/ - 0x1C4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data8 mode 0*/ - 0x1C8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data9 mode 0*/ - 0x208 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data0 mode 0*/ - 0x20C (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data1 mode 0*/ - 0x210 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data2 mode 0*/ - 0x214 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data3 mode 0*/ - 0x218 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data4 mode 0*/ - 0x21C (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data5 mode 0*/ - 0x220 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data6 mode 0*/ - 0x224 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data7 mode 0*/ + AM4372_IOPAD(0x9b0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_hd mode 0*/ + AM4372_IOPAD(0x9b4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_vd mode 0*/ + AM4372_IOPAD(0x9c0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_pclk mode 0*/ + AM4372_IOPAD(0x9c4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data8 mode 0*/ + AM4372_IOPAD(0x9c8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data9 mode 0*/ + AM4372_IOPAD(0xa08, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data0 mode 0*/ + AM4372_IOPAD(0xa0c, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data1 mode 0*/ + AM4372_IOPAD(0xa10, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data2 mode 0*/ + AM4372_IOPAD(0xa14, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data3 mode 0*/ + AM4372_IOPAD(0xa18, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data4 mode 0*/ + AM4372_IOPAD(0xa1c, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data5 mode 0*/ + AM4372_IOPAD(0xa20, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data6 mode 0*/ + AM4372_IOPAD(0xa24, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam0_data7 mode 0*/ >; }; vpfe1_pins_default: vpfe1_pins_default { pinctrl-single,pins = < - 0x1CC (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data9 mode 0*/ - 0x1D0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data8 mode 0*/ - 0x1D4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_hd mode 0*/ - 0x1D8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_vd mode 0*/ - 0x1DC (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_pclk mode 0*/ - 0x1E8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data0 mode 0*/ - 0x1EC (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data1 mode 0*/ - 0x1F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data2 mode 0*/ - 0x1F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data3 mode 0*/ - 0x1F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data4 mode 0*/ - 0x1FC (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data5 mode 0*/ - 0x200 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data6 mode 0*/ - 0x204 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data7 mode 0*/ + AM4372_IOPAD(0x9cc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data9 mode 0*/ + AM4372_IOPAD(0x9d0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data8 mode 0*/ + AM4372_IOPAD(0x9d4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_hd mode 0*/ + AM4372_IOPAD(0x9d8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_vd mode 0*/ + AM4372_IOPAD(0x9dC, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_pclk mode 0*/ + AM4372_IOPAD(0x9e8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data0 mode 0*/ + AM4372_IOPAD(0x9ec, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data1 mode 0*/ + AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data2 mode 0*/ + AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data3 mode 0*/ + AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data4 mode 0*/ + AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data5 mode 0*/ + AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data6 mode 0*/ + AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data7 mode 0*/ >; }; vpfe1_pins_sleep: vpfe1_pins_sleep { pinctrl-single,pins = < - 0x1CC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data9 mode 0*/ - 0x1D0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data8 mode 0*/ - 0x1D4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_hd mode 0*/ - 0x1D8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_vd mode 0*/ - 0x1DC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_pclk mode 0*/ - 0x1E8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data0 mode 0*/ - 0x1EC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data1 mode 0*/ - 0x1F0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data2 mode 0*/ - 0x1F4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data3 mode 0*/ - 0x1F8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data4 mode 0*/ - 0x1FC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data5 mode 0*/ - 0x200 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data6 mode 0*/ - 0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data7 mode 0*/ + AM4372_IOPAD(0x9cc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data9 mode 0*/ + AM4372_IOPAD(0x9d0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data8 mode 0*/ + AM4372_IOPAD(0x9d4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_hd mode 0*/ + AM4372_IOPAD(0x9d8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_vd mode 0*/ + AM4372_IOPAD(0x9dc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_pclk mode 0*/ + AM4372_IOPAD(0x9e8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data0 mode 0*/ + AM4372_IOPAD(0x9ec, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data1 mode 0*/ + AM4372_IOPAD(0x9f0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data2 mode 0*/ + AM4372_IOPAD(0x9f4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data3 mode 0*/ + AM4372_IOPAD(0x9f8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data4 mode 0*/ + AM4372_IOPAD(0x9fc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data5 mode 0*/ + AM4372_IOPAD(0xa00, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data6 mode 0*/ + AM4372_IOPAD(0xa04, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data7 mode 0*/ >; }; mmc3_pins_default: pinmux_mmc3_pins_default { pinctrl-single,pins = < - 0x8c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */ - 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ - 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0 */ - 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1 */ - 0x4c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2 */ - 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_be1n.mmc2_dat3 */ + AM4372_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */ + AM4372_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ + AM4372_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0 */ + AM4372_IOPAD(0x848, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1 */ + AM4372_IOPAD(0x84c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2 */ + AM4372_IOPAD(0x878, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_be1n.mmc2_dat3 */ >; }; mmc3_pins_sleep: pinmux_mmc3_pins_sleep { pinctrl-single,pins = < - 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_clk.mmc2_clk */ - 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.mmc2_cmd */ - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a1.mmc2_dat0 */ - 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a2.mmc2_dat1 */ - 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a3.mmc2_dat2 */ - 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_be1n.mmc2_dat3 */ + AM4372_IOPAD(0x88c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_clk.mmc2_clk */ + AM4372_IOPAD(0x888, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.mmc2_cmd */ + AM4372_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a1.mmc2_dat0 */ + AM4372_IOPAD(0x848, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a2.mmc2_dat1 */ + AM4372_IOPAD(0x84c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a3.mmc2_dat2 */ + AM4372_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_be1n.mmc2_dat3 */ >; }; wlan_pins_default: pinmux_wlan_pins_default { pinctrl-single,pins = < - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */ - 0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/ - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/ + AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */ + AM4372_IOPAD(0x85c, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/ + AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/ >; }; wlan_pins_sleep: pinmux_wlan_pins_sleep { pinctrl-single,pins = < - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */ - 0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/ - 0x40 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/ + AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */ + AM4372_IOPAD(0x85c, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/ + AM4372_IOPAD(0x840, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/ >; }; uart3_pins: uart3_pins { pinctrl-single,pins = < - 0x228 (PIN_INPUT | MUX_MODE0) /* uart3_rxd.uart3_rxd */ - 0x22c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */ - 0x230 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_ctsn.uart3_ctsn */ - 0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_rtsn.uart3_rtsn */ + AM4372_IOPAD(0xa28, PIN_INPUT | MUX_MODE0) /* uart3_rxd.uart3_rxd */ + AM4372_IOPAD(0xa2c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */ + AM4372_IOPAD(0xa30, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_ctsn.uart3_ctsn */ + AM4372_IOPAD(0xa34, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_rtsn.uart3_rtsn */ >; }; mcasp1_pins: mcasp1_pins { pinctrl-single,pins = < - 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + AM4372_IOPAD(0x908, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ >; }; mcasp1_sleep_pins: mcasp1_sleep_pins { pinctrl-single,pins = < - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; gpio0_pins: gpio0_pins { pinctrl-single,pins = < - 0x26c (PIN_OUTPUT | MUX_MODE9) /* spi2_cs0.gpio0_23 SEL_eMMCorNANDn */ + AM4372_IOPAD(0xa6c, PIN_OUTPUT | MUX_MODE9) /* spi2_cs0.gpio0_23 SEL_eMMCorNANDn */ >; }; emmc_pins_default: emmc_pins_default { pinctrl-single,pins = < - 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ - 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ - 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ - 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ - 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM4372_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM4372_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM4372_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM4372_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM4372_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM4372_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM4372_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM4372_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + AM4372_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM4372_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ >; }; emmc_pins_sleep: emmc_pins_sleep { pinctrl-single,pins = < - 0x00 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad0.gpio1_0 */ - 0x04 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad1.gpio1_1 */ - 0x08 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad2.gpio1_2 */ - 0x0c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad3.gpio1_3 */ - 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ - 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ - 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ - 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ - 0x80 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn1.gpio1_30 */ - 0x84 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn2.gpio1_31 */ + AM4372_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad0.gpio1_0 */ + AM4372_IOPAD(0x804, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad1.gpio1_1 */ + AM4372_IOPAD(0x808, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad2.gpio1_2 */ + AM4372_IOPAD(0x80c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad3.gpio1_3 */ + AM4372_IOPAD(0x810, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ + AM4372_IOPAD(0x814, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ + AM4372_IOPAD(0x818, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ + AM4372_IOPAD(0x81c, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ + AM4372_IOPAD(0x880, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn1.gpio1_30 */ + AM4372_IOPAD(0x884, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn2.gpio1_31 */ >; }; }; -- cgit v1.2.3 From 8e7d3dd9241e10bbff3fbf46c116b3bcdf09da5f Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:55 -0300 Subject: ARM: dts: am437x-idk-evm: Use AM4372_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-idk-evm.dts | 128 +++++++++++++++++------------------ 1 file changed, 64 insertions(+), 64 deletions(-) diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index 337fb91ee74c..76dcfc6d5f0d 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -122,137 +122,137 @@ &am43xx_pinmux { gpio_keys_pins_default: gpio_keys_pins_default { pinctrl-single,pins = < - 0x1b8 (PIN_INPUT | MUX_MODE7) /* cam0_field.gpio4_2 */ + AM4372_IOPAD(0x9b8, PIN_INPUT | MUX_MODE7) /* cam0_field.gpio4_2 */ >; }; i2c0_pins_default: i2c0_pins_default { pinctrl-single,pins = < - 0x188 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM4372_IOPAD(0x988, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM4372_IOPAD(0x98c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c0_pins_sleep: i2c0_pins_sleep { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x988, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x98c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; i2c2_pins_default: i2c2_pins_default { pinctrl-single,pins = < - 0x1e8 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data1.i2c2_scl */ - 0x1ec (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data0.i2c2_sda */ + AM4372_IOPAD(0x9e8, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data1.i2c2_scl */ + AM4372_IOPAD(0x9ec, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data0.i2c2_sda */ >; }; i2c2_pins_sleep: i2c2_pins_sleep { pinctrl-single,pins = < - 0x1e8 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1ec (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9ec, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; mmc1_pins_default: pinmux_mmc1_pins_default { pinctrl-single,pins = < - 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x1f0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x1f4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0x1f8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0x1fc (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM4372_IOPAD(0x900, PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM4372_IOPAD(0x904, PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM4372_IOPAD(0x9f0, PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM4372_IOPAD(0x9f4, PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM4372_IOPAD(0x9f8, PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM4372_IOPAD(0x9fc, PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; mmc1_pins_sleep: pinmux_mmc1_pins_sleep { pinctrl-single,pins = < - 0x100 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x104 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1f0 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1f4 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1f8 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1fc (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x160 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x900, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x904, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x960, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; ecap0_pins_default: backlight_pins_default { pinctrl-single,pins = < - 0x164 (PIN_OUTPUT | MUX_MODE0) /* ecap0_in_pwm0_out.ecap0_in_pwm0_out */ + AM4372_IOPAD(0x964, PIN_OUTPUT | MUX_MODE0) /* ecap0_in_pwm0_out.ecap0_in_pwm0_out */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td2 */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td3 */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd2 */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd3 */ + AM4372_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM4372_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM4372_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM4372_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td2 */ + AM4372_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td3 */ + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd2 */ + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd3 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM4372_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; qspi_pins_default: qspi_pins_default { pinctrl-single,pins = < - 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_csn0.qspi_csn */ - 0x88 (PIN_OUTPUT | MUX_MODE2) /* gpmc_csn3.qspi_clk */ - 0x90 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_advn_ale.qspi_d0 */ - 0x94 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_oen_ren.qspi_d1 */ - 0x98 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_wen.qspi_d2 */ - 0x9c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_be0n_cle.qspi_d3 */ + AM4372_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_csn0.qspi_csn */ + AM4372_IOPAD(0x888, PIN_OUTPUT | MUX_MODE2) /* gpmc_csn3.qspi_clk */ + AM4372_IOPAD(0x890, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_advn_ale.qspi_d0 */ + AM4372_IOPAD(0x894, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_oen_ren.qspi_d1 */ + AM4372_IOPAD(0x898, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_wen.qspi_d2 */ + AM4372_IOPAD(0x89c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_be0n_cle.qspi_d3 */ >; }; qspi_pins_sleep: qspi_pins_sleep{ pinctrl-single,pins = < - 0x7c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x87c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x888, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x890, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x894, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x898, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x89c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; }; -- cgit v1.2.3 From e98ceb23e4d0513330f97b808d4655e599113807 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:56 -0300 Subject: ARM: dts: am437x-sk-evm: Use AM4372_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sk-evm.dts | 298 ++++++++++++++++++------------------ 1 file changed, 149 insertions(+), 149 deletions(-) diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 63de2a1b4315..d82dd6e3f9b1 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -157,259 +157,259 @@ &am43xx_pinmux { matrix_keypad_pins: matrix_keypad_pins { pinctrl-single,pins = < - 0x24c (PIN_OUTPUT | MUX_MODE7) /* gpio5_13.gpio5_13 */ - 0x250 (PIN_OUTPUT | MUX_MODE7) /* spi4_sclk.gpio5_4 */ - 0x254 (PIN_INPUT | MUX_MODE7) /* spi4_d0.gpio5_5 */ - 0x258 (PIN_INPUT | MUX_MODE7) /* spi4_d1.gpio5_5 */ + AM4372_IOPAD(0xa4c, PIN_OUTPUT | MUX_MODE7) /* gpio5_13.gpio5_13 */ + AM4372_IOPAD(0xa50, PIN_OUTPUT | MUX_MODE7) /* spi4_sclk.gpio5_4 */ + AM4372_IOPAD(0xa54, PIN_INPUT | MUX_MODE7) /* spi4_d0.gpio5_5 */ + AM4372_IOPAD(0xa58, PIN_INPUT | MUX_MODE7) /* spi4_d1.gpio5_5 */ >; }; leds_pins: leds_pins { pinctrl-single,pins = < - 0x228 (PIN_OUTPUT | MUX_MODE7) /* uart3_rxd.gpio5_2 */ - 0x22c (PIN_OUTPUT | MUX_MODE7) /* uart3_txd.gpio5_3 */ - 0x230 (PIN_OUTPUT | MUX_MODE7) /* uart3_ctsn.gpio5_0 */ - 0x234 (PIN_OUTPUT | MUX_MODE7) /* uart3_rtsn.gpio5_1 */ + AM4372_IOPAD(0xa28, PIN_OUTPUT | MUX_MODE7) /* uart3_rxd.gpio5_2 */ + AM4372_IOPAD(0xa2c, PIN_OUTPUT | MUX_MODE7) /* uart3_txd.gpio5_3 */ + AM4372_IOPAD(0xa30, PIN_OUTPUT | MUX_MODE7) /* uart3_ctsn.gpio5_0 */ + AM4372_IOPAD(0xa34, PIN_OUTPUT | MUX_MODE7) /* uart3_rtsn.gpio5_1 */ >; }; i2c0_pins: i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM4372_IOPAD(0x988, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM4372_IOPAD(0x98c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; i2c1_pins: i2c1_pins { pinctrl-single,pins = < - 0x15c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ - 0x158 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ + AM4372_IOPAD(0x95c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + AM4372_IOPAD(0x958, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x0f0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ - 0x0f4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ - 0x0f8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ - 0x0fc (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ - 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ - 0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM4372_IOPAD(0x8f0, PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM4372_IOPAD(0x8f4, PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM4372_IOPAD(0x8f8, PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM4372_IOPAD(0x8fc, PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM4372_IOPAD(0x900, PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM4372_IOPAD(0x904, PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; ecap0_pins: backlight_pins { pinctrl-single,pins = < - 0x164 (PIN_OUTPUT | MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */ + AM4372_IOPAD(0x964, PIN_OUTPUT | MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */ >; }; edt_ft5306_ts_pins: edt_ft5306_ts_pins { pinctrl-single,pins = < - 0x74 (PIN_INPUT | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ - 0x78 (PIN_OUTPUT | MUX_MODE7) /* gpmc_be1n.gpio1_28 */ + AM4372_IOPAD(0x874, PIN_INPUT | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ + AM4372_IOPAD(0x878, PIN_OUTPUT | MUX_MODE7) /* gpmc_be1n.gpio1_28 */ >; }; vpfe0_pins_default: vpfe0_pins_default { pinctrl-single,pins = < - 0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_hd mode 0*/ - 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_vd mode 0*/ - 0x1b8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_field mode 0*/ - 0x1bc (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_wen mode 0*/ - 0x1c0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_pclk mode 0*/ - 0x1c4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data8 mode 0*/ - 0x1c8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data9 mode 0*/ - 0x208 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data0 mode 0*/ - 0x20c (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data1 mode 0*/ - 0x210 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data2 mode 0*/ - 0x214 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data3 mode 0*/ - 0x218 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data4 mode 0*/ - 0x21c (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data5 mode 0*/ - 0x220 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data6 mode 0*/ - 0x224 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data7 mode 0*/ + AM4372_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_hd mode 0*/ + AM4372_IOPAD(0x9b4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_vd mode 0*/ + AM4372_IOPAD(0x9b8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_field mode 0*/ + AM4372_IOPAD(0x9bc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_wen mode 0*/ + AM4372_IOPAD(0x9c0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_pclk mode 0*/ + AM4372_IOPAD(0x9c4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data8 mode 0*/ + AM4372_IOPAD(0x9c8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data9 mode 0*/ + AM4372_IOPAD(0xa08, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data0 mode 0*/ + AM4372_IOPAD(0xa0c, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data1 mode 0*/ + AM4372_IOPAD(0xa10, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data2 mode 0*/ + AM4372_IOPAD(0xa14, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data3 mode 0*/ + AM4372_IOPAD(0xa18, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data4 mode 0*/ + AM4372_IOPAD(0xa1c, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data5 mode 0*/ + AM4372_IOPAD(0xa20, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data6 mode 0*/ + AM4372_IOPAD(0xa24, PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_data7 mode 0*/ >; }; vpfe0_pins_sleep: vpfe0_pins_sleep { pinctrl-single,pins = < - 0x1b0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1b4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1b8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1bc (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1c0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1c4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1c8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x208 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x20c (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x210 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x214 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x218 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x21c (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x220 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x224 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9b0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9b4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9b8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9bc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9c0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9c4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9c8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa08, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa0c, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa10, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa14, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa18, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa1c, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa20, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa24, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x12c (PIN_OUTPUT | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ - 0x114 (PIN_OUTPUT | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x128 (PIN_OUTPUT | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x124 (PIN_OUTPUT | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x120 (PIN_OUTPUT | MUX_MODE2) /* mii1_txd0.rgmii1_td2 */ - 0x11c (PIN_OUTPUT | MUX_MODE2) /* mii1_txd1.rgmii1_td3 */ - 0x130 (PIN_INPUT | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ - 0x118 (PIN_INPUT | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x140 (PIN_INPUT | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ - 0x13c (PIN_INPUT | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x138 (PIN_INPUT | MUX_MODE2) /* mii1_rxd0.rgmii1_rd2 */ - 0x134 (PIN_INPUT | MUX_MODE2) /* mii1_rxd1.rgmii1_rd3 */ + AM4372_IOPAD(0x92c, PIN_OUTPUT | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ + AM4372_IOPAD(0x914, PIN_OUTPUT | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM4372_IOPAD(0x928, PIN_OUTPUT | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM4372_IOPAD(0x924, PIN_OUTPUT | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM4372_IOPAD(0x920, PIN_OUTPUT | MUX_MODE2) /* mii1_txd0.rgmii1_td2 */ + AM4372_IOPAD(0x91c, PIN_OUTPUT | MUX_MODE2) /* mii1_txd1.rgmii1_td3 */ + AM4372_IOPAD(0x930, PIN_INPUT | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ + AM4372_IOPAD(0x918, PIN_INPUT | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM4372_IOPAD(0x940, PIN_INPUT | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + AM4372_IOPAD(0x93c, PIN_INPUT | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM4372_IOPAD(0x938, PIN_INPUT | MUX_MODE2) /* mii1_rxd0.rgmii1_rd2 */ + AM4372_IOPAD(0x934, PIN_INPUT | MUX_MODE2) /* mii1_rxd1.rgmii1_rd3 */ /* Slave 2 */ - 0x58 (PIN_OUTPUT | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ - 0x40 (PIN_OUTPUT | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ - 0x54 (PIN_OUTPUT | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ - 0x50 (PIN_OUTPUT | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ - 0x4c (PIN_OUTPUT | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ - 0x48 (PIN_OUTPUT | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ - 0x5c (PIN_INPUT | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ - 0x44 (PIN_INPUT | MUX_MODE2) /* gpmc_a1.rgmii2_rtcl */ - 0x6c (PIN_INPUT | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ - 0x68 (PIN_INPUT | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ - 0x64 (PIN_INPUT | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ - 0x60 (PIN_INPUT | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ + AM4372_IOPAD(0x858, PIN_OUTPUT | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ + AM4372_IOPAD(0x840, PIN_OUTPUT | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ + AM4372_IOPAD(0x854, PIN_OUTPUT | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ + AM4372_IOPAD(0x850, PIN_OUTPUT | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ + AM4372_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ + AM4372_IOPAD(0x848, PIN_OUTPUT | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ + AM4372_IOPAD(0x85c, PIN_INPUT | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ + AM4372_IOPAD(0x844, PIN_INPUT | MUX_MODE2) /* gpmc_a1.rgmii2_rtcl */ + AM4372_IOPAD(0x86c, PIN_INPUT | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ + AM4372_IOPAD(0x868, PIN_INPUT | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ + AM4372_IOPAD(0x864, PIN_INPUT | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ + AM4372_IOPAD(0x860, PIN_INPUT | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) /* Slave 2 reset value */ - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x840, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x854, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x850, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x84c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x848, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM4372_IOPAD(0x948, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM4372_IOPAD(0x94c, PIN_OUTPUT | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; dss_pins: dss_pins { pinctrl-single,pins = < - 0x020 (PIN_OUTPUT | MUX_MODE1) /* gpmc ad 8 -> DSS DATA 23 */ - 0x024 (PIN_OUTPUT | MUX_MODE1) - 0x028 (PIN_OUTPUT | MUX_MODE1) - 0x02c (PIN_OUTPUT | MUX_MODE1) - 0x030 (PIN_OUTPUT | MUX_MODE1) - 0x034 (PIN_OUTPUT | MUX_MODE1) - 0x038 (PIN_OUTPUT | MUX_MODE1) - 0x03c (PIN_OUTPUT | MUX_MODE1) /* gpmc ad 15 -> DSS DATA 16 */ - 0x0a0 (PIN_OUTPUT | MUX_MODE0) /* DSS DATA 0 */ - 0x0a4 (PIN_OUTPUT | MUX_MODE0) - 0x0a8 (PIN_OUTPUT | MUX_MODE0) - 0x0ac (PIN_OUTPUT | MUX_MODE0) - 0x0b0 (PIN_OUTPUT | MUX_MODE0) - 0x0b4 (PIN_OUTPUT | MUX_MODE0) - 0x0b8 (PIN_OUTPUT | MUX_MODE0) - 0x0bc (PIN_OUTPUT | MUX_MODE0) - 0x0c0 (PIN_OUTPUT | MUX_MODE0) - 0x0c4 (PIN_OUTPUT | MUX_MODE0) - 0x0c8 (PIN_OUTPUT | MUX_MODE0) - 0x0cc (PIN_OUTPUT | MUX_MODE0) - 0x0d0 (PIN_OUTPUT | MUX_MODE0) - 0x0d4 (PIN_OUTPUT | MUX_MODE0) - 0x0d8 (PIN_OUTPUT | MUX_MODE0) - 0x0dc (PIN_OUTPUT | MUX_MODE0) /* DSS DATA 15 */ - 0x0e0 (PIN_OUTPUT | MUX_MODE0) /* DSS VSYNC */ - 0x0e4 (PIN_OUTPUT | MUX_MODE0) /* DSS HSYNC */ - 0x0e8 (PIN_OUTPUT | MUX_MODE0) /* DSS PCLK */ - 0x0ec (PIN_OUTPUT | MUX_MODE0) /* DSS AC BIAS EN */ + AM4372_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1) /* gpmc ad 8 -> DSS DATA 23 */ + AM4372_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1) + AM4372_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1) /* gpmc ad 15 -> DSS DATA 16 */ + AM4372_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* DSS DATA 0 */ + AM4372_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) + AM4372_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* DSS DATA 15 */ + AM4372_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* DSS VSYNC */ + AM4372_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* DSS HSYNC */ + AM4372_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* DSS PCLK */ + AM4372_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* DSS AC BIAS EN */ >; }; qspi_pins: qspi_pins { pinctrl-single,pins = < - 0x7c (PIN_OUTPUT | MUX_MODE3) /* gpmc_csn0.qspi_csn */ - 0x88 (PIN_OUTPUT | MUX_MODE2) /* gpmc_csn3.qspi_clk */ - 0x90 (PIN_INPUT | MUX_MODE3) /* gpmc_advn_ale.qspi_d0 */ - 0x94 (PIN_INPUT | MUX_MODE3) /* gpmc_oen_ren.qspi_d1 */ - 0x98 (PIN_INPUT | MUX_MODE3) /* gpmc_wen.qspi_d2 */ - 0x9c (PIN_INPUT | MUX_MODE3) /* gpmc_be0n_cle.qspi_d3 */ + AM4372_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE3) /* gpmc_csn0.qspi_csn */ + AM4372_IOPAD(0x888, PIN_OUTPUT | MUX_MODE2) /* gpmc_csn3.qspi_clk */ + AM4372_IOPAD(0x890, PIN_INPUT | MUX_MODE3) /* gpmc_advn_ale.qspi_d0 */ + AM4372_IOPAD(0x894, PIN_INPUT | MUX_MODE3) /* gpmc_oen_ren.qspi_d1 */ + AM4372_IOPAD(0x898, PIN_INPUT | MUX_MODE3) /* gpmc_wen.qspi_d2 */ + AM4372_IOPAD(0x89c, PIN_INPUT | MUX_MODE3) /* gpmc_be0n_cle.qspi_d3 */ >; }; mcasp1_pins: mcasp1_pins { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ - 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + AM4372_IOPAD(0x908, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ >; }; mcasp1_pins_sleep: mcasp1_pins_sleep { pinctrl-single,pins = < - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; lcd_pins: lcd_pins { pinctrl-single,pins = < - 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpcm_ad7.gpio1_7 */ + AM4372_IOPAD(0x81c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpcm_ad7.gpio1_7 */ >; }; usb1_pins: usb1_pins { pinctrl-single,pins = < - 0x2c0 (PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */ + AM4372_IOPAD(0xac0, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */ >; }; usb2_pins: usb2_pins { pinctrl-single,pins = < - 0x2c4 (PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */ + AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */ >; }; }; -- cgit v1.2.3 From 43ade6a33cbc3731e4ae11821ff8180e3b4753d5 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:57 -0300 Subject: ARM: dts: am43x-epos-evm: Use AM4372_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am43x-epos-evm.dts | 246 +++++++++++++++++------------------ 1 file changed, 123 insertions(+), 123 deletions(-) diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 47954ed990f8..746fd2b17958 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -144,228 +144,228 @@ cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */ + AM4372_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + AM4372_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ >; }; cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ - 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM4372_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; nand_flash_x8: nand_flash_x8 { pinctrl-single,pins = < - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.SELQSPIorNAND/GPIO */ - 0x0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.SELQSPIorNAND/GPIO */ + AM4372_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM4372_IOPAD(0x804, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM4372_IOPAD(0x808, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM4372_IOPAD(0x80c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM4372_IOPAD(0x810, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM4372_IOPAD(0x814, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM4372_IOPAD(0x818, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM4372_IOPAD(0x81c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM4372_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM4372_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ + AM4372_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM4372_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM4372_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM4372_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM4372_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; ecap0_pins: backlight_pins { pinctrl-single,pins = < - 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + AM4372_IOPAD(0x964, MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_sda.i2c2_sda */ - 0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_scl.i2c2_scl */ + AM4372_IOPAD(0x9c0, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_sda.i2c2_sda */ + AM4372_IOPAD(0x9c4, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_scl.i2c2_scl */ >; }; spi0_pins: pinmux_spi0_pins { pinctrl-single,pins = < - 0x150 (PIN_INPUT | MUX_MODE0) /* spi0_clk.spi0_clk */ - 0x154 (PIN_OUTPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */ - 0x158 (PIN_INPUT | MUX_MODE0) /* spi0_d1.spi0_d1 */ - 0x15c (PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0) /* spi0_clk.spi0_clk */ + AM4372_IOPAD(0x954, PIN_OUTPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */ + AM4372_IOPAD(0x958, PIN_INPUT | MUX_MODE0) /* spi0_d1.spi0_d1 */ + AM4372_IOPAD(0x95c, PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ >; }; spi1_pins: pinmux_spi1_pins { pinctrl-single,pins = < - 0x190 (PIN_INPUT | MUX_MODE3) /* mcasp0_aclkx.spi1_clk */ - 0x194 (PIN_OUTPUT | MUX_MODE3) /* mcasp0_fsx.spi1_d0 */ - 0x198 (PIN_INPUT | MUX_MODE3) /* mcasp0_axr0.spi1_d1 */ - 0x19c (PIN_OUTPUT | MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */ + AM4372_IOPAD(0x990, PIN_INPUT | MUX_MODE3) /* mcasp0_aclkx.spi1_clk */ + AM4372_IOPAD(0x994, PIN_OUTPUT | MUX_MODE3) /* mcasp0_fsx.spi1_d0 */ + AM4372_IOPAD(0x998, PIN_INPUT | MUX_MODE3) /* mcasp0_axr0.spi1_d1 */ + AM4372_IOPAD(0x99c, PIN_OUTPUT | MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ >; }; qspi1_default: qspi1_default { pinctrl-single,pins = < - 0x7c (PIN_INPUT_PULLUP | MUX_MODE3) - 0x88 (PIN_INPUT_PULLUP | MUX_MODE2) - 0x90 (PIN_INPUT_PULLUP | MUX_MODE3) - 0x94 (PIN_INPUT_PULLUP | MUX_MODE3) - 0x98 (PIN_INPUT_PULLUP | MUX_MODE3) - 0x9c (PIN_INPUT_PULLUP | MUX_MODE3) + AM4372_IOPAD(0x87c, PIN_INPUT_PULLUP | MUX_MODE3) + AM4372_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x890, PIN_INPUT_PULLUP | MUX_MODE3) + AM4372_IOPAD(0x894, PIN_INPUT_PULLUP | MUX_MODE3) + AM4372_IOPAD(0x898, PIN_INPUT_PULLUP | MUX_MODE3) + AM4372_IOPAD(0x89c, PIN_INPUT_PULLUP | MUX_MODE3) >; }; pixcir_ts_pins: pixcir_ts_pins { pinctrl-single,pins = < - 0x44 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a1.gpio1_17 */ + AM4372_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a1.gpio1_17 */ >; }; hdq_pins: pinmux_hdq_pins { pinctrl-single,pins = < - 0x234 (PIN_INPUT_PULLUP | MUX_MODE1) /* cam1_wen.hdq_gpio */ + AM4372_IOPAD(0xa34, PIN_INPUT_PULLUP | MUX_MODE1) /* cam1_wen.hdq_gpio */ >; }; dss_pins: dss_pins { pinctrl-single,pins = < - 0x020 (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */ - 0x024 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x028 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x02C (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x030 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x034 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x038 (PIN_OUTPUT_PULLUP | MUX_MODE1) - 0x03C (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */ - 0x0A0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */ - 0x0A4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0A8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0AC (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0B0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0B4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0B8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0BC (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0C0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0C4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0C8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0CC (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0D0 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0D4 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0D8 (PIN_OUTPUT_PULLUP | MUX_MODE0) - 0x0DC (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */ - 0x0E0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */ - 0x0E4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */ - 0x0E8 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */ - 0x0EC (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */ + AM4372_IOPAD(0x820, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */ + AM4372_IOPAD(0x824, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x828, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x82c, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x830, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x834, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x838, PIN_OUTPUT_PULLUP | MUX_MODE1) + AM4372_IOPAD(0x83c, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */ + AM4372_IOPAD(0x8a0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */ + AM4372_IOPAD(0x8a4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8a8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8ac, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8B8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8bc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8cc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8dc, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */ + AM4372_IOPAD(0x8e0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */ + AM4372_IOPAD(0x8e4, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */ + AM4372_IOPAD(0x8e8, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */ + AM4372_IOPAD(0x8ec, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */ >; }; display_mux_pins: display_mux_pins { pinctrl-single,pins = < /* GPMC CLK -> GPIO 2_1 to select LCD / HDMI */ - 0x08C (PIN_OUTPUT_PULLUP | MUX_MODE7) + AM4372_IOPAD(0x88C, PIN_OUTPUT_PULLUP | MUX_MODE7) >; }; vpfe1_pins_default: vpfe1_pins_default { pinctrl-single,pins = < - 0x1cc (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data9 mode 0 */ - 0x1d0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data8 mode 0 */ - 0x1d4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_hd mode 0 */ - 0x1d8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_vd mode 0 */ - 0x1dc (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_pclk mode 0 */ - 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data0 mode 0 */ - 0x1ec (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data1 mode 0 */ - 0x1f0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data2 mode 0 */ - 0x1f4 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data3 mode 0 */ - 0x1f8 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data4 mode 0 */ - 0x1fc (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data5 mode 0 */ - 0x200 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data6 mode 0 */ - 0x204 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data7 mode 0 */ + AM4372_IOPAD(0x9cc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data9 mode 0 */ + AM4372_IOPAD(0x9d0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data8 mode 0 */ + AM4372_IOPAD(0x9d4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_hd mode 0 */ + AM4372_IOPAD(0x9d8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_vd mode 0 */ + AM4372_IOPAD(0x9dc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_pclk mode 0 */ + AM4372_IOPAD(0x9e8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data0 mode 0 */ + AM4372_IOPAD(0x9ec, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data1 mode 0 */ + AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data2 mode 0 */ + AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data3 mode 0 */ + AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data4 mode 0 */ + AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data5 mode 0 */ + AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data6 mode 0 */ + AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE0) /* cam1_data7 mode 0 */ >; }; vpfe1_pins_sleep: vpfe1_pins_sleep { pinctrl-single,pins = < - 0x1cc (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1d0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1d4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1d8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1dc (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1e8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1ec (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1f0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1f4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1f8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x1fc (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x200 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) - 0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9cc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9d0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9d4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9d8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9dc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9e8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9ec, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9f0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9f4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9f8, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0x9fc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa00, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) + AM4372_IOPAD(0xa04, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) >; }; mcasp1_pins: mcasp1_pins { pinctrl-single,pins = < - 0x1a0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_ACLKR/MCASP1_ACLKX */ - 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_FSR/MCASP1_FSX */ - 0x1a8 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)/* MCASP0_AXR1/MCASP1_AXR0 */ - 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_AHCLKX/MCASP1_AXR1 */ + AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_ACLKR/MCASP1_ACLKX */ + AM4372_IOPAD(0x9a4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_FSR/MCASP1_FSX */ + AM4372_IOPAD(0x9a8, PIN_OUTPUT_PULLDOWN | MUX_MODE3)/* MCASP0_AXR1/MCASP1_AXR0 */ + AM4372_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_AHCLKX/MCASP1_AXR1 */ >; }; mcasp1_sleep_pins: mcasp1_sleep_pins { pinctrl-single,pins = < - 0x1a0 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9a4, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9a8, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; }; -- cgit v1.2.3 From f70dfa6648f138ee58d176003057b83b153c406d Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:58 -0300 Subject: ARM: dts: am57xx-beagle-x15: Use DRA7XX_CORE_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 198 ++++++++++++++++---------------- 1 file changed, 99 insertions(+), 99 deletions(-) diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index d9ba6b879fc1..d3b2a92e3a3c 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -181,97 +181,97 @@ &dra7_pmx_core { leds_pins_default: leds_pins_default { pinctrl-single,pins = < - 0x3a8 (PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */ - 0x3ac (PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */ - 0x3c0 (PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */ - 0x3c4 (PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */ + DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */ + DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */ + DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */ + DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */ >; }; i2c1_pins_default: i2c1_pins_default { pinctrl-single,pins = < - 0x400 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */ - 0x404 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */ + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */ + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */ >; }; hdmi_pins: pinmux_hdmi_pins { pinctrl-single,pins = < - 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ >; }; i2c3_pins_default: i2c3_pins_default { pinctrl-single,pins = < - 0x2a4 (PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */ - 0x2a8 (PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */ + DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */ + DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */ >; }; uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - 0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ - 0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ + DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ + DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ >; }; mmc1_pins_default: mmc1_pins_default { pinctrl-single,pins = < - 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ - 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ >; }; mmc2_pins_default: mmc2_pins_default { pinctrl-single,pins = < - 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ >; }; cpsw_pins_default: cpsw_pins_default { pinctrl-single,pins = < /* Slave 1 */ - 0x250 (PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */ - 0x254 (PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */ - 0x258 (PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */ - 0x25c (PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */ - 0x260 (PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */ - 0x264 (PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */ - 0x268 (PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */ - 0x26c (PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */ - 0x270 (PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */ - 0x274 (PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */ - 0x278 (PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */ - 0x27c (PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */ + DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */ + DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */ + DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */ + DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */ + DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */ + DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */ + DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */ + DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */ + DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */ + DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */ + DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */ + DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */ /* Slave 2 */ - 0x198 (PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */ - 0x19c (PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */ - 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */ - 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */ - 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */ - 0x1ac (PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */ - 0x1b0 (PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */ - 0x1b4 (PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */ - 0x1b8 (PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */ - 0x1bc (PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */ - 0x1c0 (PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */ - 0x1c4 (PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */ + DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */ + DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */ + DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */ + DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */ + DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */ + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */ + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */ + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */ + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */ + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */ >; }; @@ -279,115 +279,115 @@ cpsw_pins_sleep: cpsw_pins_sleep { pinctrl-single,pins = < /* Slave 1 */ - 0x250 (PIN_INPUT | MUX_MODE15) - 0x254 (PIN_INPUT | MUX_MODE15) - 0x258 (PIN_INPUT | MUX_MODE15) - 0x25c (PIN_INPUT | MUX_MODE15) - 0x260 (PIN_INPUT | MUX_MODE15) - 0x264 (PIN_INPUT | MUX_MODE15) - 0x268 (PIN_INPUT | MUX_MODE15) - 0x26c (PIN_INPUT | MUX_MODE15) - 0x270 (PIN_INPUT | MUX_MODE15) - 0x274 (PIN_INPUT | MUX_MODE15) - 0x278 (PIN_INPUT | MUX_MODE15) - 0x27c (PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15) /* Slave 2 */ - 0x198 (PIN_INPUT | MUX_MODE15) - 0x19c (PIN_INPUT | MUX_MODE15) - 0x1a0 (PIN_INPUT | MUX_MODE15) - 0x1a4 (PIN_INPUT | MUX_MODE15) - 0x1a8 (PIN_INPUT | MUX_MODE15) - 0x1ac (PIN_INPUT | MUX_MODE15) - 0x1b0 (PIN_INPUT | MUX_MODE15) - 0x1b4 (PIN_INPUT | MUX_MODE15) - 0x1b8 (PIN_INPUT | MUX_MODE15) - 0x1bc (PIN_INPUT | MUX_MODE15) - 0x1c0 (PIN_INPUT | MUX_MODE15) - 0x1c4 (PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15) >; }; davinci_mdio_pins_default: davinci_mdio_pins_default { pinctrl-single,pins = < /* MDIO */ - 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */ - 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */ + DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */ + DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */ >; }; davinci_mdio_pins_sleep: davinci_mdio_pins_sleep { pinctrl-single,pins = < - 0x23c (PIN_INPUT | MUX_MODE15) - 0x240 (PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15) >; }; tps659038_pins_default: tps659038_pins_default { pinctrl-single,pins = < - 0x418 (PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */ + DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */ >; }; tmp102_pins_default: tmp102_pins_default { pinctrl-single,pins = < - 0x3C8 (PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */ + DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */ >; }; mcp79410_pins_default: mcp79410_pins_default { pinctrl-single,pins = < - 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ + DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ >; }; usb1_pins: pinmux_usb1_pins { pinctrl-single,pins = < - 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ >; }; extcon_usb1_pins: extcon_usb1_pins { pinctrl-single,pins = < - 0x3ec (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_rtsn.gpio7_25 */ + DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_rtsn.gpio7_25 */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ - 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ - 0x370 (PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */ + DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ + DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ + DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */ >; }; clkout2_pins_default: clkout2_pins_default { pinctrl-single,pins = < - 0x294 (PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */ + DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */ >; }; clkout2_pins_sleep: clkout2_pins_sleep { pinctrl-single,pins = < - 0x294 (PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */ + DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */ >; }; mcasp3_pins_default: mcasp3_pins_default { pinctrl-single,pins = < - 0x324 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */ - 0x328 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */ - 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */ - 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */ + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */ + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */ + DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */ + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */ >; }; mcasp3_pins_sleep: mcasp3_pins_sleep { pinctrl-single,pins = < - 0x324 (PIN_INPUT | MUX_MODE15) - 0x328 (PIN_INPUT | MUX_MODE15) - 0x32c (PIN_INPUT | MUX_MODE15) - 0x330 (PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15) >; }; }; -- cgit v1.2.3 From c78be3d82e0f1590be75e6900e8194066ae78638 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:53:59 -0300 Subject: ARM: dts: dra7-evm: Use DRA7XX_CORE_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 254 ++++++++++++++++++++--------------------- 1 file changed, 127 insertions(+), 127 deletions(-) diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 864f60020124..53b3a4b97086 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -154,100 +154,100 @@ vtt_pin: pinmux_vtt_pin { pinctrl-single,pins = < - 0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */ + DRA7XX_CORE_IOPAD(0x37b4, PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */ - 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */ + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda */ + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */ - 0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0x288 (PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */ - 0x28c (PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */ + DRA7XX_CORE_IOPAD(0x3688, PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */ + DRA7XX_CORE_IOPAD(0x368c, PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */ >; }; mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < - 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */ - 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */ - 0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */ - 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */ - 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */ - 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */ + DRA7XX_CORE_IOPAD(0x37a4, PIN_INPUT | MUX_MODE0) /* spi1_sclk */ + DRA7XX_CORE_IOPAD(0x37a8, PIN_INPUT | MUX_MODE0) /* spi1_d1 */ + DRA7XX_CORE_IOPAD(0x37ac, PIN_INPUT | MUX_MODE0) /* spi1_d0 */ + DRA7XX_CORE_IOPAD(0x37b0, PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */ + DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */ + DRA7XX_CORE_IOPAD(0x37bc, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */ >; }; mcspi2_pins: pinmux_mcspi2_pins { pinctrl-single,pins = < - 0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */ - 0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ - 0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ - 0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */ + DRA7XX_CORE_IOPAD(0x37c0, PIN_INPUT | MUX_MODE0) /* spi2_sclk */ + DRA7XX_CORE_IOPAD(0x37c4, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ + DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ + DRA7XX_CORE_IOPAD(0x37cc, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */ >; }; uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */ - 0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */ - 0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */ - 0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */ + DRA7XX_CORE_IOPAD(0x37e0, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */ + DRA7XX_CORE_IOPAD(0x37e4, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */ + DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT | MUX_MODE3) /* uart1_ctsn */ + DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT | MUX_MODE3) /* uart1_rtsn */ >; }; uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */ - 0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */ - 0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */ - 0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */ + DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT | MUX_MODE0) /* uart2_rxd */ + DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT | MUX_MODE0) /* uart2_txd */ + DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT | MUX_MODE0) /* uart2_ctsn */ + DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT | MUX_MODE0) /* uart2_rtsn */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ - 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ + DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ + DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ >; }; qspi1_pins: pinmux_qspi1_pins { pinctrl-single,pins = < - 0x4c (PIN_INPUT | MUX_MODE1) /* gpmc_a3.qspi1_cs2 */ - 0x50 (PIN_INPUT | MUX_MODE1) /* gpmc_a4.qspi1_cs3 */ - 0x74 (PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ - 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ - 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ - 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ - 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ - 0x88 (PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ - 0xb8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ - 0xbc (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ + DRA7XX_CORE_IOPAD(0x344c, PIN_INPUT | MUX_MODE1) /* gpmc_a3.qspi1_cs2 */ + DRA7XX_CORE_IOPAD(0x3450, PIN_INPUT | MUX_MODE1) /* gpmc_a4.qspi1_cs3 */ + DRA7XX_CORE_IOPAD(0x3474, PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ + DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ + DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ + DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ + DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ + DRA7XX_CORE_IOPAD(0x3488, PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ + DRA7XX_CORE_IOPAD(0x34b8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ + DRA7XX_CORE_IOPAD(0x34bc, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ >; }; usb1_pins: pinmux_usb1_pins { pinctrl-single,pins = < - 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ >; }; usb2_pins: pinmux_usb2_pins { pinctrl-single,pins = < - 0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ + DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ >; }; @@ -257,60 +257,60 @@ * SW5.9 (GPMC_WPN) = LOW * SW5.1 (NAND_BOOTn) = HIGH */ pinctrl-single,pins = < - 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ - 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ - 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ - 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ - 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ - 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ - 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ - 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ - 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ - 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ - 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ - 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ - 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ - 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ - 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ - 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ - 0xd8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ - 0xb4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle */ + DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ + DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ + DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ + DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ + DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ + DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ + DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ + DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ + DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ + DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ + DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ + DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ + DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ + DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ + DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ + DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ + DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */ + DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ + DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0 */ + DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ + DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ + DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle */ >; }; cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ - 0x250 (PIN_OUTPUT | MUX_MODE0) /* rgmii0_txc.rgmii0_txc */ - 0x254 (PIN_OUTPUT | MUX_MODE0) /* rgmii0_txctl.rgmii0_txctl */ - 0x258 (PIN_OUTPUT | MUX_MODE0) /* rgmii0_td3.rgmii0_txd3 */ - 0x25c (PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd2.rgmii0_txd2 */ - 0x260 (PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd1.rgmii0_txd1 */ - 0x264 (PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd0.rgmii0_txd0 */ - 0x268 (PIN_INPUT | MUX_MODE0) /* rgmii0_rxc.rgmii0_rxc */ - 0x26c (PIN_INPUT | MUX_MODE0) /* rgmii0_rxctl.rgmii0_rxctl */ - 0x270 (PIN_INPUT | MUX_MODE0) /* rgmii0_rxd3.rgmii0_rxd3 */ - 0x274 (PIN_INPUT | MUX_MODE0) /* rgmii0_rxd2.rgmii0_rxd2 */ - 0x278 (PIN_INPUT | MUX_MODE0) /* rgmii0_rxd1.rgmii0_rxd1 */ - 0x27c (PIN_INPUT | MUX_MODE0) /* rgmii0_rxd0.rgmii0_rxd0 */ + DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txc.rgmii0_txc */ + DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txctl.rgmii0_txctl */ + DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td3.rgmii0_txd3 */ + DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd2.rgmii0_txd2 */ + DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd1.rgmii0_txd1 */ + DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd0.rgmii0_txd0 */ + DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii0_rxc.rgmii0_rxc */ + DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii0_rxctl.rgmii0_rxctl */ + DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd3.rgmii0_rxd3 */ + DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd2.rgmii0_rxd2 */ + DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd1.rgmii0_rxd1 */ + DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd0.rgmii0_rxd0 */ /* Slave 2 */ - 0x198 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ - 0x19c (PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - 0x1ac (PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - 0x1b0 (PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - 0x1b4 (PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - 0x1b8 (PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - 0x1bc (PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - 0x1c0 (PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - 0x1c4 (PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ + DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ + DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ + DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ + DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ + DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ >; }; @@ -318,85 +318,85 @@ cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 */ - 0x250 (MUX_MODE15) - 0x254 (MUX_MODE15) - 0x258 (MUX_MODE15) - 0x25c (MUX_MODE15) - 0x260 (MUX_MODE15) - 0x264 (MUX_MODE15) - 0x268 (MUX_MODE15) - 0x26c (MUX_MODE15) - 0x270 (MUX_MODE15) - 0x274 (MUX_MODE15) - 0x278 (MUX_MODE15) - 0x27c (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3650, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3654, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3658, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x365c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3660, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3664, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3668, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x366c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3670, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3674, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3678, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x367c, MUX_MODE15) /* Slave 2 */ - 0x198 (MUX_MODE15) - 0x19c (MUX_MODE15) - 0x1a0 (MUX_MODE15) - 0x1a4 (MUX_MODE15) - 0x1a8 (MUX_MODE15) - 0x1ac (MUX_MODE15) - 0x1b0 (MUX_MODE15) - 0x1b4 (MUX_MODE15) - 0x1b8 (MUX_MODE15) - 0x1bc (MUX_MODE15) - 0x1c0 (MUX_MODE15) - 0x1c4 (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < - 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ - 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ + DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < - 0x23c (MUX_MODE15) - 0x240 (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) >; }; dcan1_pins_default: dcan1_pins_default { pinctrl-single,pins = < - 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ - 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ + DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ + DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ >; }; dcan1_pins_sleep: dcan1_pins_sleep { pinctrl-single,pins = < - 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ - 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */ + DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ + DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; atl_pins: pinmux_atl_pins { pinctrl-single,pins = < - 0x298 (PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ - 0x29c (PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ + DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ + DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ >; }; mcasp3_pins: pinmux_mcasp3_pins { pinctrl-single,pins = < - 0x324 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ - 0x328 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ - 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ - 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ + DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ + DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ + DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ >; }; mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { pinctrl-single,pins = < - 0x324 (MUX_MODE15) - 0x328 (MUX_MODE15) - 0x32c (MUX_MODE15) - 0x330 (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3724, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3728, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x372c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3730, MUX_MODE15) >; }; }; -- cgit v1.2.3 From 9255ea8472d28fa61fa5fdf686fad76d399d095c Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:00 -0300 Subject: ARM: dts: dra72-evm: Use DRA7XX_CORE_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra72-evm.dts | 200 ++++++++++++++++++++-------------------- 1 file changed, 100 insertions(+), 100 deletions(-) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index d6104d5f0c01..e5cc5d307f97 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -142,158 +142,158 @@ &dra7_pmx_core { i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ - 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ >; }; i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < - 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ >; }; i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < - 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ >; }; nand_default: nand_default { pinctrl-single,pins = < - 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ - 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ - 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ - 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ - 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ - 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ - 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ - 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ - 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ - 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ - 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ - 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ - 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ - 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ - 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ - 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ - 0xd8 (PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ + DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ + DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ + DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ + DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ + DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ + DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ + DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ + DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ + DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ + DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ + DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ + DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ + DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ + DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ + DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ + DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ + DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ + DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ + DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ + DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ + DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ + DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ >; }; usb1_pins: pinmux_usb1_pins { pinctrl-single,pins = < - 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ >; }; usb2_pins: pinmux_usb2_pins { pinctrl-single,pins = < - 0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ + DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ >; }; tps65917_pins_default: tps65917_pins_default { pinctrl-single,pins = < - 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ + DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ >; }; mmc1_pins_default: mmc1_pins_default { pinctrl-single,pins = < - 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ - 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ >; }; mmc2_pins_default: mmc2_pins_default { pinctrl-single,pins = < - 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ >; }; dcan1_pins_default: dcan1_pins_default { pinctrl-single,pins = < - 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ - 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ + DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ + DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ >; }; dcan1_pins_sleep: dcan1_pins_sleep { pinctrl-single,pins = < - 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ - 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */ + DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ + DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; qspi1_pins: pinmux_qspi1_pins { pinctrl-single,pins = < - 0x74 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ - 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ - 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ - 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ - 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ - 0x88 (PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ - 0xb8 (PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ + DRA7XX_CORE_IOPAD(0x3474, PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ + DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ + DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ + DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ + DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ + DRA7XX_CORE_IOPAD(0x3488, PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ + DRA7XX_CORE_IOPAD(0x34b8, PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ >; }; hdmi_pins: pinmux_hdmi_pins { pinctrl-single,pins = < - 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ + DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ >; }; atl_pins: pinmux_atl_pins { pinctrl-single,pins = < - 0x298 (PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ - 0x29c (PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ + DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ + DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ >; }; mcasp3_pins: pinmux_mcasp3_pins { pinctrl-single,pins = < - 0x324 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ - 0x328 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ - 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ - 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ + DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ + DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ + DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ >; }; mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { pinctrl-single,pins = < - 0x324 (PIN_INPUT_PULLDOWN | MUX_MODE15) - 0x328 (PIN_INPUT_PULLDOWN | MUX_MODE15) - 0x32c (PIN_INPUT_PULLDOWN | MUX_MODE15) - 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15) >; }; }; @@ -627,18 +627,18 @@ cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 2 */ - 0x198 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ - 0x19c (PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - 0x1ac (PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - 0x1b0 (PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - 0x1b4 (PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - 0x1b8 (PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - 0x1bc (PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - 0x1c0 (PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - 0x1c4 (PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ + DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ + DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ + DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ + DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ + DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ >; }; @@ -646,33 +646,33 @@ cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 2 */ - 0x198 (MUX_MODE15) - 0x19c (MUX_MODE15) - 0x1a0 (MUX_MODE15) - 0x1a4 (MUX_MODE15) - 0x1a8 (MUX_MODE15) - 0x1ac (MUX_MODE15) - 0x1b0 (MUX_MODE15) - 0x1b4 (MUX_MODE15) - 0x1b8 (MUX_MODE15) - 0x1bc (MUX_MODE15) - 0x1c0 (MUX_MODE15) - 0x1c4 (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) >; }; davinci_mdio_default: davinci_mdio_default { pinctrl-single,pins = < /* MDIO */ - 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ - 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ + DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ >; }; davinci_mdio_sleep: davinci_mdio_sleep { pinctrl-single,pins = < - 0x23c (MUX_MODE15) - 0x240 (MUX_MODE15) + DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) >; }; }; -- cgit v1.2.3 From 161312d6e2fa4627e4b3af0a535db3b9af1654e3 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:01 -0300 Subject: ARM: dts: omap3-beagle: Use OMAP3_*_IOPAD pinmux macros Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle.dts | 64 +++++++++++++++++++------------------- 1 file changed, 32 insertions(+), 32 deletions(-) diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 274c2c482aaa..8dcf84ac79bb 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -171,7 +171,7 @@ &omap3_pmx_wkup { gpio1_pins: pinmux_gpio1_pins { pinctrl-single,pins = < - 0x14 (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */ >; }; }; @@ -195,47 +195,47 @@ uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >; }; tfp410_pins: pinmux_tfp410_pins { pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ >; }; dss_dpi_pins: pinmux_dss_dpi_pins { pinctrl-single,pins = < - 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ - 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ - 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ - 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ - 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ - 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ - 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ - 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ - 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ - 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ - 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ - 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ - 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ - 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ - 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ - 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ - 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ - 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ - 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ - 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ - 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ - 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ - 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ - 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ - 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ - 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ - 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ - 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ >; }; }; -- cgit v1.2.3 From 0ba47e43064cbde72ec4c7dd4af1dd73ce6727fb Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:02 -0300 Subject: ARM: dts: omap3-beagle-xm: Use OMAP3_*_IOPAD pinmux macros Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle-xm.dts | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 73f1e3a8f62c..5e0bf475051e 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -176,18 +176,18 @@ &omap3_pmx_wkup { gpio1_pins: pinmux_gpio1_pins { pinctrl-single,pins = < - 0x0e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */ + OMAP3_WKUP_IOPAD(0x2a0e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */ >; }; dss_dpi_pins2: pinmux_dss_dpi_pins1 { pinctrl-single,pins = < - 0x0a (PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */ - 0x0c (PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */ - 0x10 (PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */ - 0x12 (PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */ - 0x14 (PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */ - 0x16 (PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */ + OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */ + OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */ + OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */ + OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */ + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */ >; }; }; @@ -200,8 +200,8 @@ uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ >; }; -- cgit v1.2.3 From 8acf1b30c8b5ee0893e11747da0cf26e8a3561c8 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:03 -0300 Subject: ARM: dts: omap3-evm-37xx: Use OMAP3_*_IOPAD pinmux macros Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-evm-37xx.dts | 54 ++++++++++++++++++------------------ 1 file changed, 27 insertions(+), 27 deletions(-) diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts index bb339d1648e0..ac188657a95d 100644 --- a/arch/arm/boot/dts/omap3-evm-37xx.dts +++ b/arch/arm/boot/dts/omap3-evm-37xx.dts @@ -66,48 +66,48 @@ mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - 0x120 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ - 0x122 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ - 0x124 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ - 0x126 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ + OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ + OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ + OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ >; }; /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */ mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ - 0x12e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >; }; wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0x150 (PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */ - 0x14e (PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */ + OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */ + OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */ >; }; smsc911x_pins: pinmux_smsc911x_pins { pinctrl-single,pins = < - 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ >; }; }; @@ -115,12 +115,12 @@ &omap3_pmx_wkup { dss_dpi_pins2: pinmux_dss_dpi_pins1 { pinctrl-single,pins = < - 0x0a (PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */ - 0x0c (PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */ - 0x10 (PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */ - 0x12 (PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */ - 0x14 (PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */ - 0x16 (PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */ + OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */ + OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */ + OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */ + OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */ + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */ >; }; }; -- cgit v1.2.3 From 97f4817ccec6f3e336c953893baf7970b36ee9d1 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:04 -0300 Subject: ARM: dts: omap3-ldp: Use OMAP3_CORE1_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-ldp.dts | 42 ++++++++++++++++++++--------------------- 1 file changed, 21 insertions(+), 21 deletions(-) diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts index d2fab8c0d4f8..0d0f1a7444f7 100644 --- a/arch/arm/boot/dts/omap3-ldp.dts +++ b/arch/arm/boot/dts/omap3-ldp.dts @@ -224,32 +224,32 @@ &omap3_pmx_core { gpio_key_pins: pinmux_gpio_key_pins { pinctrl-single,pins = < - 0xea (PIN_INPUT | MUX_MODE4) /* cam_d2.gpio_101 */ - 0xec (PIN_INPUT | MUX_MODE4) /* cam_d3.gpio_102 */ - 0xee (PIN_INPUT | MUX_MODE4) /* cam_d4.gpio_103 */ - 0xf0 (PIN_INPUT | MUX_MODE4) /* cam_d5.gpio_104 */ - 0xf2 (PIN_INPUT | MUX_MODE4) /* cam_d6.gpio_105 */ - 0xf4 (PIN_INPUT | MUX_MODE4) /* cam_d7.gpio_106 */ - 0xf6 (PIN_INPUT | MUX_MODE4) /* cam_d8.gpio_107 */ - 0xf8 (PIN_INPUT | MUX_MODE4) /* cam_d9.gpio_108 */ - 0xfa (PIN_INPUT | MUX_MODE4) /* cam_d10.gpio_109 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE4) /* cam_d2.gpio_101 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE4) /* cam_d3.gpio_102 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE4) /* cam_d4.gpio_103 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE4) /* cam_d5.gpio_104 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE4) /* cam_d6.gpio_105 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE4) /* cam_d7.gpio_106 */ + OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE4) /* cam_d8.gpio_107 */ + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE4) /* cam_d9.gpio_108 */ + OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT | MUX_MODE4) /* cam_d10.gpio_109 */ >; }; musb_pins: pinmux_musb_pins { pinctrl-single,pins = < - 0x172 (PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ - 0x17a (PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ - 0x17c (PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ - 0x17e (PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ - 0x180 (PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ - 0x182 (PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ - 0x184 (PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ - 0x186 (PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ - 0x188 (PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ - 0x176 (PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ - 0x178 (PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ - 0x174 (PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ >; }; -- cgit v1.2.3 From 675e457c456d14178db951aa4f34f0ee7358394b Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:05 -0300 Subject: ARM: dts: omap3-n900: Use OMAP3_CORE1_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 106 +++++++++++++++++++-------------------- 1 file changed, 53 insertions(+), 53 deletions(-) diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 5f5e0f3d5b64..f8a20f32e26c 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -149,15 +149,15 @@ uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */ - 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ + OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */ + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */ + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */ >; }; @@ -198,22 +198,22 @@ i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */ - 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda */ + OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl */ - 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */ - 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */ + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ >; }; @@ -225,85 +225,85 @@ mcspi4_pins: pinmux_mcspi4_pins { pinctrl-single,pins = < - 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */ - 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */ - 0x160 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */ - 0x166 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */ + OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */ + OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */ + OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */ + OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ - 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ >; }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ - 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ - 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */ - 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */ - 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */ - 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */ >; }; acx565akm_pins: pinmux_acx565akm_pins { pinctrl-single,pins = < - 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ >; }; dss_sdi_pins: pinmux_dss_sdi_pins { pinctrl-single,pins = < - 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */ - 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */ - 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */ - 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */ - 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */ - 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */ >; }; wl1251_pins: pinmux_wl1251 { pinctrl-single,pins = < - 0x0ce (PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */ - 0x05a (PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */ + OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */ >; }; ssi_pins: pinmux_ssi { pinctrl-single,pins = < - 0x150 (PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */ - 0x14e (PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */ - 0x152 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */ - 0x14c (PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */ - 0x154 (PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */ - 0x156 (PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */ - 0x158 (PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */ - 0x15a (PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */ + OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */ + OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */ + OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */ + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */ + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */ + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */ + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */ >; }; modem_pins: pinmux_modem { pinctrl-single,pins = < - 0x0ac (PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */ - 0x0b0 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */ - 0x0b2 (PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */ - 0x0b4 (PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */ - 0x0b6 (PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */ - 0x15e (PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */ >; }; }; -- cgit v1.2.3 From 53ccdd4b998df6125c83365d097eddeb3ad9da81 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:06 -0300 Subject: ARM: dts: omap3-n9: Use OMAP3_CORE1_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n950-n9.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index e9ee1df0e467..a2c2b8d8dd2c 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -36,12 +36,12 @@ &omap3_pmx_core { mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ - 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ >; }; }; -- cgit v1.2.3 From ff523e3167662843019fe44293b68490fb8b99b5 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:07 -0300 Subject: ARM: dts: omap3-zoom3: Use OMAP3_*_IOPAD pinmux macros Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-zoom3.dts | 60 +++++++++++++++++++-------------------- 1 file changed, 30 insertions(+), 30 deletions(-) diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts index 7bc5fdd6981e..f19170bdcc1f 100644 --- a/arch/arm/boot/dts/omap3-zoom3.dts +++ b/arch/arm/boot/dts/omap3-zoom3.dts @@ -54,27 +54,27 @@ /* REVISIT: twl gpio0 is mmc0_cd */ mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - 0x116 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ >; }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ - 0x12c (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ - 0x12e (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ - 0x130 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ - 0x132 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ - 0x134 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat4.sdmmc2_dat4 */ - 0x136 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat5.sdmmc2_dat5 */ - 0x138 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat6.sdmmc2_dat6 */ - 0x13a (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat4.sdmmc2_dat4 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat5.sdmmc2_dat5 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat6.sdmmc2_dat6 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */ >; }; @@ -87,35 +87,35 @@ uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x150 (PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */ - 0x14e (PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */ - 0x152 (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ - 0x14c (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ + OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */ + OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */ + OMAP3_CORE1_IOPAD(0x2182, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ >; }; uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0x144 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ - 0x146 (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ - 0x14a (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ - 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ + OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ + OMAP3_CORE1_IOPAD(0x217a, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16a (PIN_INPUT_PULLDOWN | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ - 0x16c (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ - 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ + OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ + OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >; }; /* wl12xx GPIO output for WLAN_EN */ wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0xea (PIN_OUTPUT| MUX_MODE4) /* cam_d2.gpio_101 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_OUTPUT| MUX_MODE4) /* cam_d2.gpio_101 */ >; }; }; @@ -135,7 +135,7 @@ &omap3_pmx_wkup { wlan_host_wkup: pinmux_wlan_host_wkup_pins { pinctrl-single,pins = < - 0x1a (PIN_INPUT_PULLUP | MUX_MODE4) /* sys_clkout1.gpio_10 WLAN_HOST_WKUP */ + OMAP3_WKUP_IOPAD(0x2a1a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_clkout1.gpio_10 WLAN_HOST_WKUP */ >; }; }; -- cgit v1.2.3 From ececfa31e5e54f5bf9d4459bac0b6092ee244ece Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:08 -0300 Subject: ARM: dts: twl4030: Use OMAP3_CORE1_IOPAD pinmux macro Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/twl4030_omap3.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/twl4030_omap3.dtsi b/arch/arm/boot/dts/twl4030_omap3.dtsi index 3537ae5b2146..5288e6dffef7 100644 --- a/arch/arm/boot/dts/twl4030_omap3.dtsi +++ b/arch/arm/boot/dts/twl4030_omap3.dtsi @@ -19,7 +19,7 @@ */ twl4030_pins: pinmux_twl4030_pins { pinctrl-single,pins = < - 0x1b0 (PIN_INPUT_PULLUP | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* sys_nirq.sys_nirq */ + OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* sys_nirq.sys_nirq */ >; }; }; -- cgit v1.2.3 From 37990123cdba3e7d4db14ea96caef8e40b2e4354 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:09 -0300 Subject: ARM: dts: omap4-panda-a4: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-panda-a4.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index 133f1b74e8ae..78d363177762 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -13,8 +13,8 @@ /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ - 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; -- cgit v1.2.3 From 0e3ae3281d82245e939d159948bc2ffa3d607991 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:10 -0300 Subject: ARM: dts: omap4-panda-common: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-panda-common.dtsi | 164 +++++++++++++++--------------- 1 file changed, 82 insertions(+), 82 deletions(-) diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 18d096696fc0..df2e356ec089 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -199,129 +199,129 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ - 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ + OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ + OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ - 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ - 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ - 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ - 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ - 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ - 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ - 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ + OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ + OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ + OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ + OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ >; }; dss_dpi_pins: pinmux_dss_dpi_pins { pinctrl-single,pins = < - 0x122 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */ - 0x124 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */ - 0x126 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */ - 0x128 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */ - 0x12a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */ - 0x12c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */ - 0x12e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */ - 0x130 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */ - 0x132 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */ - 0x134 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */ - 0x136 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */ - - 0x174 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */ - 0x176 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */ - 0x178 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */ - 0x17a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */ - 0x17c (PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */ - 0x17e (PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */ - 0x180 (PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */ - 0x182 (PIN_OUTPUT | MUX_MODE5) /* dispc2_de */ - 0x184 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */ - 0x186 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */ - 0x188 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */ - 0x18a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */ - 0x18c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */ - 0x18e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */ - - 0x190 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */ - 0x192 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */ - 0x194 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */ + OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */ + OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */ + OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */ + OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */ + OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */ + OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */ + OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */ + OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */ + OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */ + OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */ + OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */ + + OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */ + OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */ + OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */ + OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */ + OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */ + OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */ + OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */ + OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */ + OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */ + OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */ + OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */ + OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */ + OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */ + OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */ + + OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */ + OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */ + OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */ >; }; tfp410_pins: pinmux_tfp410_pins { pinctrl-single,pins = < - 0x144 (PIN_OUTPUT | MUX_MODE3) /* gpio_0 */ + OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */ >; }; dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < - 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ - 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ - 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ + OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ + OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ + OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ >; }; hsusbb1_pins: pinmux_hsusbb1_pins { pinctrl-single,pins = < - 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ - 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ - 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ - 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ - 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ - 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ - 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ - 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ - 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ - 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ - 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ - 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ + OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ + OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ + OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ + OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ + OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ + OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ + OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ + OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ + OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ + OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ + OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ + OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ - 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ - 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ - 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ >; }; i2c4_pins: pinmux_i2c4_pins { pinctrl-single,pins = < - 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ - 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ + OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; @@ -331,24 +331,24 @@ */ wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0x26 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ - 0x2c (PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */ - 0x30 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */ - 0x32 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */ + OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ + OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */ + OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */ + OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */ >; }; /* wl12xx GPIO inputs and SDIO pins */ wl12xx_pins: pinmux_wl12xx_pins { pinctrl-single,pins = < - 0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ - 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ - 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ - 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ - 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ - 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ + OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ + OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ + OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ >; }; }; @@ -356,8 +356,8 @@ &omap4_pmx_wkup { led_wkgpio_pins: pinmux_leds_wkpins { pinctrl-single,pins = < - 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ - 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ + OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ >; }; }; -- cgit v1.2.3 From 67832f527790b9778f4765b23bb4768c5cf8d11c Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:11 -0300 Subject: ARM: dts: omap4-panda-es: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-panda-es.dts | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 2f1dabcc6adf..119f8e657edc 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -34,23 +34,23 @@ /* PandaboardES has external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ - 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; &omap4_pmx_core { led_gpio_pins: gpio_led_pmx { pinctrl-single,pins = < - 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ + OMAP4_IOPAD(0x0f6, PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; }; &led_wkgpio_pins { pinctrl-single,pins = < - 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ >; }; -- cgit v1.2.3 From b6bf441ea420135078c632d5d25275756eba66ca Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:12 -0300 Subject: ARM: dts: omap4-sdp: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-sdp.dts | 110 ++++++++++++++++++++-------------------- 1 file changed, 55 insertions(+), 55 deletions(-) diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index f0bdc41f8eff..aae513265dc2 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -212,143 +212,143 @@ uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0xd8 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ - 0xda (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ - 0xdc (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */ - 0xde (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ + OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ - 0x102 (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ - 0x104 (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x106 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ + OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ + OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >; }; uart4_pins: pinmux_uart4_pins { pinctrl-single,pins = < - 0x11c (PIN_INPUT | MUX_MODE0) /* uart4_rx.uart4_rx */ - 0x11e (PIN_OUTPUT | MUX_MODE0) /* uart4_tx.uart4_tx */ + OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx.uart4_rx */ + OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx.uart4_tx */ >; }; twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ - 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ + OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ + OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ - 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ - 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ - 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ - 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ >; }; dmic_pins: pinmux_dmic_pins { pinctrl-single,pins = < - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* abe_dmic_clk1.abe_dmic_clk1 */ - 0xd2 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din1.abe_dmic_din1 */ - 0xd4 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din2.abe_dmic_din2 */ - 0xd6 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din3.abe_dmic_din3 */ + OMAP4_IOPAD(0x110, PIN_OUTPUT | MUX_MODE0) /* abe_dmic_clk1.abe_dmic_clk1 */ + OMAP4_IOPAD(0x112, PIN_INPUT | MUX_MODE0) /* abe_dmic_din1.abe_dmic_din1 */ + OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE0) /* abe_dmic_din2.abe_dmic_din2 */ + OMAP4_IOPAD(0x116, PIN_INPUT | MUX_MODE0) /* abe_dmic_din3.abe_dmic_din3 */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ - 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ - 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ - 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ + OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ + OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ + OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ + OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ >; }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < - 0xb6 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx.abe_mcbsp2_clkx */ - 0xb8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dr.abe_mcbsp2_dr */ - 0xba (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dx.abe_mcbsp2_dx */ - 0xbc (PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx.abe_mcbsp2_fsx */ + OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx.abe_mcbsp2_clkx */ + OMAP4_IOPAD(0x0f8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dr.abe_mcbsp2_dr */ + OMAP4_IOPAD(0x0fa, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dx.abe_mcbsp2_dx */ + OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx.abe_mcbsp2_fsx */ >; }; mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < - 0xf2 (PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ - 0xf4 (PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ - 0xf6 (PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ - 0xf8 (PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + OMAP4_IOPAD(0x132, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP4_IOPAD(0x134, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP4_IOPAD(0x136, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP4_IOPAD(0x138, PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ >; }; dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < - 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ - 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ - 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ + OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ + OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ + OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ - 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ - 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ - 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ >; }; i2c4_pins: pinmux_i2c4_pins { pinctrl-single,pins = < - 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ - 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ + OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; /* wl12xx GPIO output for WLAN_EN */ wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0x3c (PIN_OUTPUT | MUX_MODE3) /* gpmc_nwp.gpio_54 */ + OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) /* gpmc_nwp.gpio_54 */ >; }; /* wl12xx GPIO inputs and SDIO pins */ wl12xx_pins: pinmux_wl12xx_pins { pinctrl-single,pins = < - 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ - 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ - 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ - 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ - 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ + OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ + OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ >; }; }; -- cgit v1.2.3 From ed04b3747ceabdabf6f808e7a1f878d727ce6478 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:13 -0300 Subject: ARM: dts: omap4-sdp-es23plus: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-sdp-es23plus.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/omap4-sdp-es23plus.dts index aad5dda0f469..b4d19a7ae393 100644 --- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts +++ b/arch/arm/boot/dts/omap4-sdp-es23plus.dts @@ -10,8 +10,8 @@ /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ - 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; -- cgit v1.2.3 From 56ed5665ebde995210d4a7f7a0ba7d1d67bc82f7 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:14 -0300 Subject: ARM: dts: twl6030: Use OMAP4_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/twl6030_omap4.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/twl6030_omap4.dtsi b/arch/arm/boot/dts/twl6030_omap4.dtsi index a4fa5703c42b..e373f59cea9c 100644 --- a/arch/arm/boot/dts/twl6030_omap4.dtsi +++ b/arch/arm/boot/dts/twl6030_omap4.dtsi @@ -24,7 +24,7 @@ &omap4_pmx_wkup { twl6030_wkup_pins: pinmux_twl6030_wkup_pins { pinctrl-single,pins = < - 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */ + OMAP4_IOPAD(0x054, PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */ >; }; }; @@ -32,7 +32,7 @@ &omap4_pmx_core { twl6030_pins: pinmux_twl6030_pins { pinctrl-single,pins = < - 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */ + OMAP4_IOPAD(0x19e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */ >; }; }; -- cgit v1.2.3 From 2fcf367a6c4abc2fe6f4f50b4ef81bd81fbd656f Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:15 -0300 Subject: ARM: dts: omap5-board-common: Use OMAP5_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-board-common.dtsi | 94 +++++++++++++++---------------- 1 file changed, 47 insertions(+), 47 deletions(-) diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi index 5cf76a1c5c75..888412c63f97 100644 --- a/arch/arm/boot/dts/omap5-board-common.dtsi +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -139,60 +139,60 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ + OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ - 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ - 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ - 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ - 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ + OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ + OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ + OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ + OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ - 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ - 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ - 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ + OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ + OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ + OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ + OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ >; }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ - 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ - 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ - 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ + OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ + OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ + OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ + OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ - 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ >; }; mcspi2_pins: pinmux_mcspi2_pins { pinctrl-single,pins = < - 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ - 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ - 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ + OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ + OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ >; }; mcspi3_pins: pinmux_mcspi3_pins { pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ + OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ >; }; @@ -215,59 +215,59 @@ usbhost_pins: pinmux_usbhost_pins { pinctrl-single,pins = < - 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ - 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ - 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ - 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ - 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ - 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ + OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ + OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ >; }; led_gpio_pins: pinmux_led_gpio_pins { pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ + OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ >; }; uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ - 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ + OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ + OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ + OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ + OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ - 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ + OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ + OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ >; }; uart5_pins: pinmux_uart5_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ - 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ - 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ - 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ + OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ + OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ + OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ + OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ >; }; dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < - 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ - 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ + OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ + OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ >; }; }; @@ -280,13 +280,13 @@ usbhost_wkup_pins: pinmux_usbhost_wkup_pins { pinctrl-single,pins = < - 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ + OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ >; }; wlcore_irq_pin: pinmux_wlcore_irq_pin { pinctrl-single,pins = < - OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ + OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ >; }; }; -- cgit v1.2.3 From 92245d420e76e332aa4eb37b022c367d57a93076 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:16 -0300 Subject: ARM: dts: omap5-cm-t54: Use OMAP5_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-cm-t54.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts index 3774b37be6c8..0c03dca9ea04 100644 --- a/arch/arm/boot/dts/omap5-cm-t54.dts +++ b/arch/arm/boot/dts/omap5-cm-t54.dts @@ -175,7 +175,7 @@ ads7846_pins: pinmux_ads7846_pins { pinctrl-single,pins = < - 0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ + OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ >; }; }; -- cgit v1.2.3 From 03c84de82e817122bf51f66a34d17f0dc1061f88 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Fri, 13 Nov 2015 01:54:17 -0300 Subject: ARM: dts: omap5-uevm.dts: Use OMAP5_IOPAD pinmux macro Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 05b1c1ebded8..60b3fbb3bf07 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -40,8 +40,8 @@ &omap5_pmx_core { i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < - 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ - 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ + OMAP5_IOPAD(0x1c6, PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + OMAP5_IOPAD(0x1c8, PIN_INPUT | MUX_MODE0) /* i2c5_sda */ >; }; }; -- cgit v1.2.3 From df10eadfce3510c2814e95d9f3d2d5d2c64eb26b Mon Sep 17 00:00:00 2001 From: "Andrew F. Davis" Date: Fri, 13 Nov 2015 10:47:27 -0600 Subject: ARM: dts: am335x-boneblack: Use pinctrl constants and AM33XX_IOPAD macro Using constants for pinctrl allows better readability and removes redundancy with comments. AM33XX_IOPAD allows us to use part of the pinctrl physical address as in the TRM instead of an offset. Signed-off-by: Andrew F. Davis Reviewed-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++----------------- 1 file changed, 22 insertions(+), 22 deletions(-) diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index eadbba32386d..55c0e954b146 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -36,32 +36,32 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { pinctrl-single,pins = < - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ >; }; nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { pinctrl-single,pins = < - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ >; }; }; -- cgit v1.2.3 From 8ca31dbf67b3ad65b629e8185086050fa6b29dbc Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Thu, 12 Nov 2015 15:07:40 +0100 Subject: ARM: dts: add dm816x pwm property to timers Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their PWM output fonctionnality via the dmtimer driver. Cc: Brian Hutchinson Signed-off-by: Neil Armstrong Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm816x.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index 3c99cfa1a876..342e37db7246 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -319,6 +319,7 @@ reg = <0x48044000 0x2000>; interrupts = <92>; ti,hwmods = "timer4"; + ti,timer-pwm; }; timer5: timer@48046000 { @@ -326,6 +327,7 @@ reg = <0x48046000 0x2000>; interrupts = <93>; ti,hwmods = "timer5"; + ti,timer-pwm; }; timer6: timer@48048000 { @@ -333,6 +335,7 @@ reg = <0x48048000 0x2000>; interrupts = <94>; ti,hwmods = "timer6"; + ti,timer-pwm; }; timer7: timer@4804a000 { @@ -340,6 +343,7 @@ reg = <0x4804a000 0x2000>; interrupts = <95>; ti,hwmods = "timer7"; + ti,timer-pwm; }; uart1: uart@48020000 { -- cgit v1.2.3 From 727535fd2032985c987a34b7e5853512424237d5 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Thu, 12 Nov 2015 15:07:45 +0100 Subject: ARM: dts: remove dm816x invalid DT l3_main hwmod Remove invalid l3_main hwmod entry from dm816x DT ocp node. Cc: Brian Hutchinson Signed-off-by: Neil Armstrong Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm816x.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index 342e37db7246..2fde534db6c6 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -64,7 +64,6 @@ #address-cells = <1>; #size-cells = <1>; ranges; - ti,hwmods = "l3_main"; prcm: prcm@48180000 { compatible = "ti,dm816-prcm"; -- cgit v1.2.3 From 24f098220c43fb9ac32f6a667dfd102e2bdae671 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Thu, 12 Nov 2015 15:07:49 +0100 Subject: ARM: dts: Add omap4-hwspinlock support in dm816x Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox. Cc: Brian Hutchinson Signed-off-by: Neil Armstrong Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm816x.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index 2fde534db6c6..f9286c3bdedc 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -225,6 +225,13 @@ }; }; + spinbox: spinbox@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x2000>; + ti,hwmods = "spinbox"; + #hwlock-cells = <1>; + }; + mdio: mdio@4a100800 { compatible = "ti,davinci_mdio"; #address-cells = <1>; -- cgit v1.2.3 From 201c7e3386059204c0048384900c82276e0a37fe Mon Sep 17 00:00:00 2001 From: Franklin S Cooper Jr Date: Thu, 15 Oct 2015 12:37:27 -0500 Subject: ARM: dts: am437x/am33xx/omap/dm816x: Add gpmc dma channel Add dma channel information to the gpmc. Although not enabled by default this will allow prefetch-dma to be used. Signed-off-by: Franklin S Cooper Jr Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am33xx.dtsi | 2 ++ arch/arm/boot/dts/am4372.dtsi | 2 ++ arch/arm/boot/dts/dm816x.dtsi | 2 ++ arch/arm/boot/dts/omap3.dtsi | 2 ++ arch/arm/boot/dts/omap4.dtsi | 2 ++ arch/arm/boot/dts/omap5.dtsi | 2 ++ 6 files changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index d23e2524d694..9b8861891bf0 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -819,6 +819,8 @@ ti,no-idle-on-init; reg = <0x50000000 0x2000>; interrupts = <100>; + dmas = <&edma 52>; + dma-names = "rxtx"; gpmc,num-cs = <7>; gpmc,num-waitpins = <2>; #address-cells = <2>; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index d83ff9c9701e..1695b684e29d 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -842,6 +842,8 @@ gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; + dmas = <&edma 52>; + dma-names = "rxtx"; clocks = <&l3s_gclk>; clock-names = "fck"; reg = <0x50000000 0x2000>; diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index f9286c3bdedc..b6543a865102 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -179,6 +179,8 @@ #address-cells = <2>; #size-cells = <1>; interrupts = <100>; + dmas = <&edma 52>; + dma-names = "rxtx"; gpmc,num-cs = <6>; gpmc,num-waitpins = <2>; }; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 8a2b25332b8c..d1ffabb7c74f 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -717,6 +717,8 @@ ti,hwmods = "gpmc"; reg = <0x6e000000 0x02d0>; interrupts = <20>; + dmas = <&sdma 4>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; #address-cells = <2>; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 5a206c100ce2..32b65be7d423 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -354,6 +354,8 @@ #address-cells = <2>; #size-cells = <1>; interrupts = ; + dmas = <&sdma 4>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 4c04389dab32..ca3c17fde5a0 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -391,6 +391,8 @@ #address-cells = <2>; #size-cells = <1>; interrupts = ; + dmas = <&sdma 4>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; -- cgit v1.2.3 From f81902e44a2738a3228c96f2307f449cfc0acc89 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Fri, 23 Oct 2015 07:20:23 -0500 Subject: ARM: dts: Add audio support for LogicPD Torpedo DM3730 devkit Use the TWL4030 Codec with mcbsp2 on Torpedo. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 10 ++++++++++ arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 13 +++++++++++++ 2 files changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index 5b0430041ec6..afc13e58cffb 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -48,6 +48,12 @@ }; }; + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -67,6 +73,10 @@ }; }; +&mcbsp2 { + status = "okay"; +}; + &charger { ti,bb-uvolt = <3200000>; ti,bb-uamp = <150>; diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 36387b11451d..9777ff44eb67 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -96,6 +96,11 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; }; }; @@ -136,6 +141,14 @@ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ >; }; + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ + OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ + OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ + OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ + >; + }; }; &omap3_pmx_core2 { -- cgit v1.2.3 From 6b3d42c6fcc472082ad9b1482111f487719f826a Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Fri, 23 Oct 2015 07:23:14 -0500 Subject: ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit When used with the Logic PD development kit, this makes the I2C buses match the BSP released by Logic PD. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 9777ff44eb67..c8091ff81d74 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -104,6 +104,14 @@ }; }; +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; + /* * Only found on the wireless SOM. For the SOM without wireless, the pins for * MMC3 can be routed with jumpers to the second MMC slot on the devkit and -- cgit v1.2.3 From 2d11961f3e554ca7f90ce3ee2ed42421edd1e776 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Fri, 23 Oct 2015 07:27:33 -0500 Subject: ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively The development kit schematic expects VAUX1 to be 3.0V. Most users use the development kit as a reference. The development kit schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. If the voltage is too high it could damage the processor. If it's too low, it won't work. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index afc13e58cffb..b07d1d92c974 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -73,6 +73,16 @@ }; }; +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + &mcbsp2 { status = "okay"; }; -- cgit v1.2.3 From 9ff502f58a2b723b6226cf13b2daf931d1d20c37 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Mon, 26 Oct 2015 07:27:37 -0500 Subject: ARM: dts: Enable UART2 pinctrl on LogicPD Torpedo + Wireless module Setup UART2 for communication at 3MBps with flow control. Signed-off-by: Adam Ford [tony@atomide.com: dropped the kim changes, that binding has been removed] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index c8091ff81d74..78c52436cddb 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -157,6 +157,21 @@ OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ >; }; + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ + OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ + >; + }; +}; + +&uart2 { + interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; }; &omap3_pmx_core2 { -- cgit v1.2.3 From 7cd6ca770d1b067e6ddc7207a16755da7ea9bd09 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Mon, 26 Oct 2015 07:42:38 -0500 Subject: ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit When used with the Logic PD development kit, this makes the I2C buses match the BSP released by Logic PD. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-som.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 78c52436cddb..7fed0bd4f3de 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -112,6 +112,14 @@ clock-frequency = <400000>; }; +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; + /* * Only found on the wireless SOM. For the SOM without wireless, the pins for * MMC3 can be routed with jumpers to the second MMC slot on the devkit and -- cgit v1.2.3 From b6f0f6c40b664638e2da6e6a940c7ef41592e3ab Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Mon, 26 Oct 2015 07:53:10 -0500 Subject: ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo The schematic expects VAUX1 to be 3.0V attached to the debug port. The schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index b07d1d92c974..b017871aeddc 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -83,6 +83,16 @@ regulator-max-microvolt = <1800000>; }; +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + &mcbsp2 { status = "okay"; }; -- cgit v1.2.3 From 15be8179e46aa8adc303f8585acd3c626ca678dc Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:08 +0200 Subject: ARM: dts: cm-t335: add initial support Add basic support for CompuLab cm-t335 module based on AM335X SoC. CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip. The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus. Current patch adds support: UART0 and GPIO LED Detailed description can be found at the module site: http://www.compulab.co.il/products/computer-on-modules/cm-t335/ Signed-off-by: Ilya Ledvich [uri.mashiach@compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration] Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/omap/omap.txt | 3 ++ arch/arm/boot/dts/Makefile | 7 +-- arch/arm/boot/dts/am335x-cm-t335.dts | 62 ++++++++++++++++++++++ 3 files changed, 69 insertions(+), 3 deletions(-) create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 9f4e5136e568..2154f9797714 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -138,6 +138,9 @@ Boards: - AM335X phyBOARD-WEGA: Single Board Computer dev kit compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4 + compatible = "compulab,cm-t335", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..15411bc99aca 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -459,13 +459,14 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-bone.dtb \ am335x-boneblack.dtb \ am335x-bonegreen.dtb \ - am335x-sl50.dtb \ + am335x-chiliboard.dtb \ + am335x-cm-t335.dtb \ am335x-evm.dtb \ am335x-evmsk.dtb \ + am335x-lxm.dtb \ am335x-nano.dtb \ am335x-pepper.dtb \ - am335x-lxm.dtb \ - am335x-chiliboard.dtb \ + am335x-sl50.dtb \ am335x-wega-rdk.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-duovero-parlor.dtb \ diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts new file mode 100644 index 000000000000..e18859ec2a7d --- /dev/null +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -0,0 +1,62 @@ +/* + * am335x-cm-t335.dts - Device Tree file for Compulab CM-T335 + * + * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "CompuLab CM-T335"; + compatible = "compulab,cm-t335", "ti,am33xx"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x8000000>; /* 128 MB */ + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_led_pins>; + led@0 { + label = "cm_t335:green"; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; /* gpio2_0 */ + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <>; + + gpio_led_pins: pinmux_gpio_led_pins { + pinctrl-single,pins = < + /* gpmc_csn3.gpio2_0 */ + AM33XX_IOPAD(0x888, PIN_OUTPUT | MUX_MODE7) + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; -- cgit v1.2.3 From 43577ecfcaa28bb21bd19739c35d96c444bdf1a8 Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:09 +0200 Subject: ARM: dts: cm-t335: add basic support for I2C Add pinmux configuration for I2C0 and I2C1 pins. Add description for I2C0 bus, set clock frequency to 400kHz. Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus. Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 37 ++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index e18859ec2a7d..9fc2f011ea47 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -37,6 +37,24 @@ pinctrl-names = "default"; pinctrl-0 = <>; + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) + /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + /* uart0_ctsn.i2c1_sda */ + AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE2) + /* uart0_rtsn.i2c1_scl */ + AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2) + >; + }; + gpio_led_pins: pinmux_gpio_led_pins { pinctrl-single,pins = < /* gpmc_csn3.gpio2_0 */ @@ -60,3 +78,22 @@ status = "okay"; }; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + /* CM-T335 board EEPROM */ + eeprom: 24c02@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + /* Real Time Clock */ + ext_rtc: em3027@56 { + compatible = "emmicro,em3027"; + reg = <0x56>; + }; +}; -- cgit v1.2.3 From 440c3a1c65c16784420ff87af2e903c3b0fe9e5f Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:10 +0200 Subject: ARM: dts: cm-t335: add support for NAND flash Add pinmux configuration for NAND specific GPMC pins. Add description for GPMC controller. Add child node for NAND flash including CM-T335 specific partition table to GPMC node. Enable error-location module (ELM). Acked-by: Igor Grinberg Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 106 +++++++++++++++++++++++++++++++++++ 1 file changed, 106 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index 9fc2f011ea47..57c8b031369c 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -62,6 +62,41 @@ >; }; + nandflash_pins: pinmux_nandflash_pins { + pinctrl-single,pins = < + /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) + /* gpmc_wpn.gpio0_30 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) + /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) + /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) + /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) + /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) + /* gpmc_ben0_cle.gpmc_ben0_cle */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) + >; + }; + uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < /* uart0_rxd.uart0_rxd */ @@ -97,3 +132,74 @@ reg = <0x56>; }; }; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "spl"; + reg = <0x00000000 0x00200000>; + }; + partition@1 { + label = "uboot"; + reg = <0x00200000 0x00100000>; + }; + partition@2 { + label = "uboot environment"; + reg = <0x00300000 0x00100000>; + }; + partition@3 { + label = "dtb"; + reg = <0x00400000 0x00100000>; + }; + partition@4 { + label = "splash"; + reg = <0x00500000 0x00400000>; + }; + partition@5 { + label = "linux"; + reg = <0x00900000 0x00600000>; + }; + partition@6 { + label = "rootfs"; + reg = <0x00F00000 0>; + }; + }; +}; + +&elm { + status = "okay"; +}; -- cgit v1.2.3 From 54f0c5ceba9633e816c69a56258b43561490bade Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:11 +0200 Subject: ARM: dts: cm-t335: add support for MMC Add pinmux configuration for MMC0 pins. Add fixed regulator 'vmmc_fixed'. Enable MMC0 in 4-bit mode. Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index 57c8b031369c..486810f36128 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -31,6 +31,14 @@ linux,default-trigger = "heartbeat"; }; }; + + /* regulator for mmc */ + vmmc_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmc_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &am33xx_pinmux { @@ -105,6 +113,23 @@ AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) >; }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + /* mmc0_dat3.mmc0_dat3 */ + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) + /* mmc0_dat2.mmc0_dat2 */ + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) + /* mmc0_dat1.mmc0_dat1 */ + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) + /* mmc0_dat0.mmc0_dat0 */ + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) + /* mmc0_clk.mmc0_clk */ + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) + /* mmc0_cmd.mmc0_cmd */ + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) + >; + }; }; &uart0 { @@ -203,3 +228,11 @@ &elm { status = "okay"; }; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc_fixed>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; +}; -- cgit v1.2.3 From 3a8038eef06189898b04e4a9209720f54853d0f6 Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:12 +0200 Subject: ARM: dts: cm-t335: add support for network device Add pinmux configurations for RGMII1 based CPSW Ethernet pins and MDIO pins: - default configuration required for module in active state, - sleep configuration required for module in inactive state. Add mac node with single slave device. Add nodes for davinci_mdio and cpsw_emac0. Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 85 ++++++++++++++++++++++++++++++++++++ 1 file changed, 85 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index 486810f36128..3aec38a482db 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -114,6 +114,71 @@ >; }; + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + /* mii1_tx_en.rgmii1_tctl */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) + /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) + /* mii1_rxd0.rgmii1_rd0 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) + /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < /* mmc0_dat3.mmc0_dat3 */ @@ -229,6 +294,26 @@ status = "okay"; }; +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + slaves = <1>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + &mmc1 { status = "okay"; vmmc-supply = <&vmmc_fixed>; -- cgit v1.2.3 From 07f1c49c1561127c7f394481bb58bf83e15b71a9 Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 24 Nov 2015 16:02:13 +0200 Subject: ARM: dts: cm-t335: add support for PWM backlight Add pinmux configuration for ECAP0 pin. Add node for PWM backlight device. Use PWM output from ecap0 as backlight source. Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index 3aec38a482db..31ff1aa07b43 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -39,6 +39,13 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 0>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; }; &am33xx_pinmux { @@ -114,6 +121,13 @@ >; }; + ecap0_pins: pinmux_ecap0_pins { + pinctrl-single,pins = < + /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + AM33XX_IOPAD(0x964, 0x0) + >; + }; + cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ @@ -223,6 +237,16 @@ }; }; +&epwmss0 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; + }; +}; + &gpmc { status = "okay"; pinctrl-names = "default"; -- cgit v1.2.3 From 8e6ebfaa9b384088002baa10f7534efa73a0794e Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 27 Oct 2015 13:36:36 +0100 Subject: regulator: tps65217: remove tps65217.dtsi file remove tps65217.dtsi and adapt all boards, which used it. Signed-off-by: Heiko Schocher Tested-by: Keerthy Acked-by: Mark Brown Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- .../devicetree/bindings/regulator/tps65217.txt | 10 ++++ arch/arm/boot/dts/am335x-bone-common.dtsi | 14 ++++-- arch/arm/boot/dts/am335x-chilisom.dtsi | 14 +++++- arch/arm/boot/dts/am335x-nano.dts | 14 +++++- arch/arm/boot/dts/am335x-pepper.dts | 14 +++++- arch/arm/boot/dts/am335x-sl50.dts | 13 ++++- arch/arm/boot/dts/tps65217.dtsi | 56 ---------------------- 7 files changed, 68 insertions(+), 67 deletions(-) delete mode 100644 arch/arm/boot/dts/tps65217.dtsi diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index 4f05d208c95c..d18109657da6 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -26,7 +26,11 @@ Example: ti,pmic-shutdown-controller; regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: dcdc1 { + reg = <0>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -34,6 +38,7 @@ Example: }; dcdc2_reg: dcdc2 { + reg = <1>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -41,6 +46,7 @@ Example: }; dcdc3_reg: dcc3 { + reg = <2>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; @@ -48,6 +54,7 @@ Example: }; ldo1_reg: ldo1 { + reg = <3>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -55,6 +62,7 @@ Example: }; ldo2_reg: ldo2 { + reg = <4>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -62,6 +70,7 @@ Example: }; ldo3_reg: ldo3 { + reg = <5>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -69,6 +78,7 @@ Example: }; ldo4_reg: ldo4 { + reg = <6>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 0cc150b87b86..f3db13d2d90e 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -285,10 +285,8 @@ }; }; - -/include/ "tps65217.dtsi" - &tps { + compatible = "ti,tps65217"; /* * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only * mode") at poweroff. Most BeagleBone versions do not support RTC-only @@ -309,12 +307,17 @@ ti,pmic-shutdown-controller; regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: regulator@0 { + reg = <0>; regulator-name = "vdds_dpr"; regulator-always-on; }; dcdc2_reg: regulator@1 { + reg = <1>; /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ regulator-name = "vdd_mpu"; regulator-min-microvolt = <925000>; @@ -324,6 +327,7 @@ }; dcdc3_reg: regulator@2 { + reg = <2>; /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ regulator-name = "vdd_core"; regulator-min-microvolt = <925000>; @@ -333,21 +337,25 @@ }; ldo1_reg: regulator@3 { + reg = <3>; regulator-name = "vio,vrtc,vdds"; regulator-always-on; }; ldo2_reg: regulator@4 { + reg = <4>; regulator-name = "vdd_3v3aux"; regulator-always-on; }; ldo3_reg: regulator@5 { + reg = <5>; regulator-name = "vdd_1v8"; regulator-always-on; }; ldo4_reg: regulator@6 { + reg = <6>; regulator-name = "vdd_3v3a"; regulator-always-on; }; diff --git a/arch/arm/boot/dts/am335x-chilisom.dtsi b/arch/arm/boot/dts/am335x-chilisom.dtsi index 857d9894103a..fda457b07e15 100644 --- a/arch/arm/boot/dts/am335x-chilisom.dtsi +++ b/arch/arm/boot/dts/am335x-chilisom.dtsi @@ -128,16 +128,21 @@ }; -/include/ "tps65217.dtsi" - &tps { + compatible = "ti,tps65217"; + regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: regulator@0 { + reg = <0>; regulator-name = "vdds_dpr"; regulator-always-on; }; dcdc2_reg: regulator@1 { + reg = <1>; /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ regulator-name = "vdd_mpu"; regulator-min-microvolt = <925000>; @@ -147,6 +152,7 @@ }; dcdc3_reg: regulator@2 { + reg = <2>; /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ regulator-name = "vdd_core"; regulator-min-microvolt = <925000>; @@ -156,24 +162,28 @@ }; ldo1_reg: regulator@3 { + reg = <3>; regulator-name = "vio,vrtc,vdds"; regulator-boot-on; regulator-always-on; }; ldo2_reg: regulator@4 { + reg = <4>; regulator-name = "vdd_3v3aux"; regulator-boot-on; regulator-always-on; }; ldo3_reg: regulator@5 { + reg = <5>; regulator-name = "vdd_1v8"; regulator-boot-on; regulator-always-on; }; ldo4_reg: regulator@6 { + reg = <6>; regulator-name = "vdd_3v3d"; regulator-boot-on; regulator-always-on; diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts index f313999c503e..77559a1ded60 100644 --- a/arch/arm/boot/dts/am335x-nano.dts +++ b/arch/arm/boot/dts/am335x-nano.dts @@ -375,11 +375,15 @@ wp-gpios = <&gpio3 18 0>; }; -#include "tps65217.dtsi" - &tps { + compatible = "ti,tps65217"; + regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: regulator@0 { + reg = <0>; /* +1.5V voltage with ±4% tolerance */ regulator-min-microvolt = <1450000>; regulator-max-microvolt = <1550000>; @@ -388,6 +392,7 @@ }; dcdc2_reg: regulator@1 { + reg = <1>; /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */ regulator-name = "vdd_mpu"; regulator-min-microvolt = <915000>; @@ -397,6 +402,7 @@ }; dcdc3_reg: regulator@2 { + reg = <2>; /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */ regulator-name = "vdd_core"; regulator-min-microvolt = <915000>; @@ -406,6 +412,7 @@ }; ldo1_reg: regulator@3 { + reg = <3>; /* +1.8V voltage with ±4% tolerance */ regulator-min-microvolt = <1750000>; regulator-max-microvolt = <1870000>; @@ -414,6 +421,7 @@ }; ldo2_reg: regulator@4 { + reg = <4>; /* +3.3V voltage with ±4% tolerance */ regulator-min-microvolt = <3175000>; regulator-max-microvolt = <3430000>; @@ -422,6 +430,7 @@ }; ldo3_reg: regulator@5 { + reg = <5>; /* +1.8V voltage with ±4% tolerance */ regulator-min-microvolt = <1750000>; regulator-max-microvolt = <1870000>; @@ -430,6 +439,7 @@ }; ldo4_reg: regulator@6 { + reg = <6>; /* +3.3V voltage with ±4% tolerance */ regulator-min-microvolt = <3175000>; regulator-max-microvolt = <3430000>; diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts index f9d7239ebdaf..9cb77a120319 100644 --- a/arch/arm/boot/dts/am335x-pepper.dts +++ b/arch/arm/boot/dts/am335x-pepper.dts @@ -427,9 +427,9 @@ vin-supply = <&vbat>; }; -/include/ "tps65217.dtsi" - &tps { + compatible = "ti,tps65217"; + backlight { isel = <1>; /* ISET1 */ fdim = <200>; /* TPS65217_BL_FDIM_200HZ */ @@ -437,12 +437,17 @@ }; regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: regulator@0 { + reg = <0>; /* VDD_1V8 system supply */ regulator-always-on; }; dcdc2_reg: regulator@1 { + reg = <1>; /* VDD_CORE voltage limits 0.95V - 1.26V with +/-4% tolerance */ regulator-name = "vdd_core"; regulator-min-microvolt = <925000>; @@ -452,6 +457,7 @@ }; dcdc3_reg: regulator@2 { + reg = <2>; /* VDD_MPU voltage limits 0.95V - 1.1V with +/-4% tolerance */ regulator-name = "vdd_mpu"; regulator-min-microvolt = <925000>; @@ -461,18 +467,21 @@ }; ldo1_reg: regulator@3 { + reg = <3>; /* VRTC 1.8V always-on supply */ regulator-name = "vrtc,vdds"; regulator-always-on; }; ldo2_reg: regulator@4 { + reg = <4>; /* 3.3V rail */ regulator-name = "vdd_3v3aux"; regulator-always-on; }; ldo3_reg: regulator@5 { + reg = <5>; /* VDD_3V3A 3.3V rail */ regulator-name = "vdd_3v3a"; regulator-min-microvolt = <3300000>; @@ -480,6 +489,7 @@ }; ldo4_reg: regulator@6 { + reg = <6>; /* VDD_3V3B 3.3V rail */ regulator-name = "vdd_3v3b"; regulator-always-on; diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/am335x-sl50.dts index 3303c281697b..d38edfa53bb9 100644 --- a/arch/arm/boot/dts/am335x-sl50.dts +++ b/arch/arm/boot/dts/am335x-sl50.dts @@ -375,16 +375,19 @@ pinctrl-0 = <&uart4_pins>; }; -#include "tps65217.dtsi" - &tps { + compatible = "ti,tps65217"; ti,pmic-shutdown-controller; interrupt-parent = <&intc>; interrupts = <7>; /* NNMI */ regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: regulator@0 { + reg = <0>; /* VDDS_DDR */ regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -392,6 +395,7 @@ }; dcdc2_reg: regulator@1 { + reg = <1>; /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ regulator-name = "vdd_mpu"; regulator-min-microvolt = <925000>; @@ -401,6 +405,7 @@ }; dcdc3_reg: regulator@2 { + reg = <2>; /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ regulator-name = "vdd_core"; regulator-min-microvolt = <925000>; @@ -410,6 +415,7 @@ }; ldo1_reg: regulator@3 { + reg = <3>; /* VRTC / VIO / VDDS*/ regulator-always-on; regulator-min-microvolt = <1800000>; @@ -417,6 +423,7 @@ }; ldo2_reg: regulator@4 { + reg = <4>; /* VDD_3V3AUX */ regulator-always-on; regulator-min-microvolt = <3300000>; @@ -424,6 +431,7 @@ }; ldo3_reg: regulator@5 { + reg = <5>; /* VDD_1V8 */ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -431,6 +439,7 @@ }; ldo4_reg: regulator@6 { + reg = <6>; /* VDD_3V3A */ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/tps65217.dtsi b/arch/arm/boot/dts/tps65217.dtsi deleted file mode 100644 index a63272422d76..000000000000 --- a/arch/arm/boot/dts/tps65217.dtsi +++ /dev/null @@ -1,56 +0,0 @@ -/* - * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -/* - * Integrated Power Management Chip - * http://www.ti.com/lit/ds/symlink/tps65217.pdf - */ - -&tps { - compatible = "ti,tps65217"; - - regulators { - #address-cells = <1>; - #size-cells = <0>; - - dcdc1_reg: regulator@0 { - reg = <0>; - regulator-compatible = "dcdc1"; - }; - - dcdc2_reg: regulator@1 { - reg = <1>; - regulator-compatible = "dcdc2"; - }; - - dcdc3_reg: regulator@2 { - reg = <2>; - regulator-compatible = "dcdc3"; - }; - - ldo1_reg: regulator@3 { - reg = <3>; - regulator-compatible = "ldo1"; - }; - - ldo2_reg: regulator@4 { - reg = <4>; - regulator-compatible = "ldo2"; - }; - - ldo3_reg: regulator@5 { - reg = <5>; - regulator-compatible = "ldo3"; - }; - - ldo4_reg: regulator@6 { - reg = <6>; - regulator-compatible = "ldo4"; - }; - }; -}; -- cgit v1.2.3 From 258511e1ee2a74783eb73ffae7e52d622bb67707 Mon Sep 17 00:00:00 2001 From: Franklin S Cooper Jr Date: Wed, 28 Oct 2015 16:02:16 -0500 Subject: ARM: dts: omap4: Add elm node Add device tree entry for the error location module. Signed-off-by: Franklin S Cooper Jr Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 32b65be7d423..2bd9c83300b2 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -348,6 +348,14 @@ #interrupt-cells = <2>; }; + elm: elm@48078000 { + compatible = "ti,am3352-elm"; + reg = <0x48078000 0x2000>; + interrupts = <4>; + ti,hwmods = "elm"; + status = "disabled"; + }; + gpmc: gpmc@50000000 { compatible = "ti,omap4430-gpmc"; reg = <0x50000000 0x1000>; -- cgit v1.2.3 From 6cab180d9ba3c38da50fc32eb90c33fc9e77b81f Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 17 Nov 2015 09:24:15 +0100 Subject: arm, am335x: add support for the bosch shc board add support for the am335x based shc board. UART: 0-2 and 4 DRAM: 512 MiB MMC: OMAP SD/MMC: 0 @ 26 MHz OMAP SD/MMC: 1 @ 26 MHz I2C: at24 eeprom, pcf8563 USB: USB1 (host) Signed-off-by: Heiko Schocher Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-shc.dts | 577 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 578 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-shc.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 15411bc99aca..518db314b039 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -466,6 +466,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-lxm.dtb \ am335x-nano.dtb \ am335x-pepper.dtb \ + am335x-shc.dtb \ am335x-sl50.dtb \ am335x-wega-rdk.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ diff --git a/arch/arm/boot/dts/am335x-shc.dts b/arch/arm/boot/dts/am335x-shc.dts new file mode 100644 index 000000000000..1b5b044fcd91 --- /dev/null +++ b/arch/arm/boot/dts/am335x-shc.dts @@ -0,0 +1,577 @@ +/* + * support for the bosch am335x based shc c3 board + * + * Copyright, C) 2015 Heiko Schocher + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include + +/ { + model = "Bosch SHC"; + compatible = "ti,am335x-shc", "ti,am335x-bone", "ti,am33xx"; + + aliases { + mmcblk0 = &mmc1; + mmcblk1 = &mmc2; + }; + + cpus { + cpu@0 { + /* + * To consider voltage drop between PMIC and SoC, + * tolerance value is reduced to 2% from 4% and + * voltage value is increased as a precaution. + */ + operating-points = < + /* kHz uV */ + 594000 1225000 + 294000 1125000 + >; + voltage-tolerance = <2>; /* 2 percentage */ + cpu0-supply = <&dcdc2_reg>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + back_button { + label = "Back Button"; + gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; + linux,code = ; + debounce-interval = <1000>; + gpio-key,wakeup; + }; + + front_button { + label = "Front Button"; + gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>; + linux,code = ; + debounce-interval = <1000>; + gpio-key,wakeup; + }; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_s0>; + + compatible = "gpio-leds"; + + led@1 { + label = "shc:power:red"; + gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led@2 { + label = "shc:power:bl"; + gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "timer"; + default-state = "on"; + }; + + led@3 { + label = "shc:lan:red"; + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led@4 { + label = "shc:lan:bl"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led@5 { + label = "shc:cloud:red"; + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led@6 { + label = "shc:cloud:bl"; + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&aes { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; + +&epwmss1 { + status = "okay"; + + ehrpwm1: ehrpwm@48302200 { + pinctrl-names = "default"; + pinctrl-0 = <&ehrpwm1_pins>; + status = "okay"; + }; +}; + +&gpio1 { + hmtc_rst { + gpio-hog; + gpios = <24 GPIO_ACTIVE_LOW>; + output-high; + line-name = "homematic_reset"; + }; + + hmtc_prog { + gpio-hog; + gpios = <27 GPIO_ACTIVE_LOW>; + output-high; + line-name = "homematic_program"; + }; +}; + +&gpio3 { + zgb_rst { + gpio-hog; + gpios = <18 GPIO_ACTIVE_LOW>; + output-low; + line-name = "zigbee_reset"; + }; + + zgb_boot { + gpio-hog; + gpios = <19 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "zigbee_boot"; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + + at24@50 { + compatible = "at24,24c32"; + pagesize = <32>; + reg = <0x50>; + }; + + pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; + slaves = <1>; + cpsw_emac0: slave@4a100200 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "mii"; + phy-handle = <ðernetphy0>; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + bus-width = <0x4>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-inverted; + max-frequency = <26000000>; + vmmc-supply = <&vmmcsd_fixed>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + max-frequency = <26000000>; + sd-uhs-sdr25; + vmmc-supply = <&vmmcsd_fixed>; + status = "okay"; +}; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; + bus-width = <4>; + cap-power-off-card; + max-frequency = <26000000>; + sd-uhs-sdr25; + vmmc-supply = <&vmmcsd_fixed>; + status = "okay"; +}; + +&rtc { + ti,no-init; +}; + +&sham { + status = "okay"; +}; + +&tps { + compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-name = "vdds_dpr"; + regulator-compatible = "dcdc1"; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1450000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + /* + * VDD_MPU voltage limits 0.95V - 1.26V with + * +/-4% tolerance + */ + regulator-compatible = "dcdc2"; + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1375000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <70000>; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + /* + * VDD_CORE voltage limits 0.95V - 1.1V with + * +/-4% tolerance + */ + regulator-name = "vdd_core"; + regulator-compatible = "dcdc3"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1125000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-name = "vio,vrtc,vdds"; + regulator-compatible = "ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-name = "vdd_3v3aux"; + regulator-compatible = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-name = "vdd_1v8"; + regulator-compatible = "ldo3"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-name = "vdd_3v3a"; + regulator-compatible = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + /* xdma_event_intr1.clkout2 */ + AM33XX_IOPAD(0x9b4, PIN_INPUT | MUX_MODE6) + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE0) + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) + /* mdio_clk.mdio_clk */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + ehrpwm1_pins: pinmux_ehrpwm1 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE6) /* gpmc_a3.gpio1_19 */ + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x880, PIN_INPUT | MUX_MODE2) + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x988, PIN_INPUT | MUX_MODE0) + AM33XX_IOPAD(0x98c, PIN_INPUT | MUX_MODE0) + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE5) + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x830, PIN_INPUT | MUX_MODE3) + AM33XX_IOPAD(0x834, PIN_INPUT | MUX_MODE3) + AM33XX_IOPAD(0x838, PIN_INPUT | MUX_MODE3) + AM33XX_IOPAD(0x83c, PIN_INPUT | MUX_MODE3) + AM33XX_IOPAD(0x888, PIN_INPUT | MUX_MODE3) + AM33XX_IOPAD(0x88c, PIN_INPUT | MUX_MODE3) + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x968, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x96c, PIN_OUTPUT | MUX_MODE0) + AM33XX_IOPAD(0x970, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x974, PIN_OUTPUT | MUX_MODE0) + >; + }; + + uart1_pins: pinmux_uart1 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x978, PIN_INPUT_PULLDOWN | MUX_MODE0) + AM33XX_IOPAD(0x97C, PIN_OUTPUT | MUX_MODE0) + AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE0) + AM33XX_IOPAD(0x984, PIN_OUTPUT | MUX_MODE0) + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) + AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) + >; + }; + + uart4_pins: pinmux_uart4_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) + AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE6) + >; + }; + + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x844, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLUP | MUX_MODE7) + AM33XX_IOPAD(0x860, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x864, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x86c, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7) + AM33XX_IOPAD(0x87c, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x894, PIN_INPUT | MUX_MODE7) + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x958, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x95c, PIN_OUTPUT | MUX_MODE7) + AM33XX_IOPAD(0x964, PIN_OUTPUT_PULLUP | MUX_MODE7) + AM33XX_IOPAD(0x9a0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x9a8, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE7) + >; + }; +}; -- cgit v1.2.3 From 480b2b32a42d8247c93cd3ba51f94a8f582bd4dc Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Thu, 19 Nov 2015 12:31:01 +0530 Subject: ARM: dts: dra7: add spi alias for qspi Set the alias for qspi to spi0 Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index bc672fb91466..b2badf9110f7 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -41,6 +41,7 @@ ethernet1 = &cpsw_emac1; d_can0 = &dcan1; d_can1 = &dcan2; + spi0 = &qspi; }; timer { -- cgit v1.2.3 From 23d711ab4dec7552cad8d03d12e253ac66e70a95 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 30 Nov 2015 15:16:51 +0100 Subject: ARM: shmobile: sh73a0: Add MSIOF clocks The 4 MSIOF clocks are MSTP clocks, and children of the SUB clock. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/sh73a0.dtsi | 28 ++++++++++++++++------------ include/dt-bindings/clock/sh73a0-clock.h | 6 +++++- 2 files changed, 21 insertions(+), 13 deletions(-) diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 319551f0fcdb..635564ab98ed 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -812,13 +812,13 @@ mstp0_clks: mstp0_clks@e6150130 { compatible = "renesas,sh73a0-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0xe6150130 4>, <0xe6150030 4>; - clocks = <&cpg_clocks SH73A0_CLK_HP>; + clocks = <&cpg_clocks SH73A0_CLK_HP>, <&sub_clk>; #clock-cells = <1>; clock-indices = < - SH73A0_CLK_IIC2 + SH73A0_CLK_IIC2 SH73A0_CLK_MSIOF0 >; clock-output-names = - "iic2"; + "iic2", "msiof0"; }; mstp1_clks: mstp1_clks@e6150134 { compatible = "renesas,sh73a0-mstp-clocks", "renesas,cpg-mstp-clocks"; @@ -848,20 +848,24 @@ reg = <0xe6150138 4>, <0xe6150040 4>; clocks = <&sub_clk>, <&cpg_clocks SH73A0_CLK_HP>, <&cpg_clocks SH73A0_CLK_HP>, <&sub_clk>, - <&sub_clk>, <&sub_clk>, <&sub_clk>, <&sub_clk>, - <&sub_clk>, <&sub_clk>; + <&sub_clk>, <&sub_clk>, <&sub_clk>, + <&sub_clk>, <&sub_clk>, <&sub_clk>, + <&sub_clk>, <&sub_clk>, <&sub_clk>; #clock-cells = <1>; clock-indices = < SH73A0_CLK_SCIFA7 SH73A0_CLK_SY_DMAC - SH73A0_CLK_MP_DMAC SH73A0_CLK_SCIFA5 - SH73A0_CLK_SCIFB SH73A0_CLK_SCIFA0 - SH73A0_CLK_SCIFA1 SH73A0_CLK_SCIFA2 - SH73A0_CLK_SCIFA3 SH73A0_CLK_SCIFA4 + SH73A0_CLK_MP_DMAC SH73A0_CLK_MSIOF3 + SH73A0_CLK_MSIOF1 SH73A0_CLK_SCIFA5 + SH73A0_CLK_SCIFB SH73A0_CLK_MSIOF2 + SH73A0_CLK_SCIFA0 SH73A0_CLK_SCIFA1 + SH73A0_CLK_SCIFA2 SH73A0_CLK_SCIFA3 + SH73A0_CLK_SCIFA4 >; clock-output-names = - "scifa7", "sy_dmac", "mp_dmac", "scifa5", - "scifb", "scifa0", "scifa1", "scifa2", - "scifa3", "scifa4"; + "scifa7", "sy_dmac", "mp_dmac", "msiof3", + "msiof1", "scifa5", "scifb", "msiof2", + "scifa0", "scifa1", "scifa2", "scifa3", + "scifa4"; }; mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,sh73a0-mstp-clocks", "renesas,cpg-mstp-clocks"; diff --git a/include/dt-bindings/clock/sh73a0-clock.h b/include/dt-bindings/clock/sh73a0-clock.h index 53369568c24c..2eca353a29d7 100644 --- a/include/dt-bindings/clock/sh73a0-clock.h +++ b/include/dt-bindings/clock/sh73a0-clock.h @@ -28,7 +28,8 @@ #define SH73A0_CLK_HP 14 /* MSTP0 */ -#define SH73A0_CLK_IIC2 1 +#define SH73A0_CLK_IIC2 1 +#define SH73A0_CLK_MSIOF0 0 /* MSTP1 */ #define SH73A0_CLK_CEU1 29 @@ -45,8 +46,11 @@ #define SH73A0_CLK_SCIFA7 19 #define SH73A0_CLK_SY_DMAC 18 #define SH73A0_CLK_MP_DMAC 17 +#define SH73A0_CLK_MSIOF3 15 +#define SH73A0_CLK_MSIOF1 8 #define SH73A0_CLK_SCIFA5 7 #define SH73A0_CLK_SCIFB 6 +#define SH73A0_CLK_MSIOF2 5 #define SH73A0_CLK_SCIFA0 4 #define SH73A0_CLK_SCIFA1 3 #define SH73A0_CLK_SCIFA2 2 -- cgit v1.2.3 From d74f61fee39d5896913d268b60884b13b43edee7 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 30 Nov 2015 15:16:52 +0100 Subject: ARM: shmobile: sh73a0: Add MSIOF device nodes The sh73a0 has 4 MSIOF devices, located in the A3SP power area. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/sh73a0.dtsi | 44 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 635564ab98ed..3a6056f9f0d2 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -273,6 +273,50 @@ status = "disabled"; }; + msiof0: spi@e6e20000 { + compatible = "renesas,msiof-sh73a0", "renesas,sh-mobile-msiof"; + reg = <0xe6e20000 0x0064>; + interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks SH73A0_CLK_MSIOF0>; + power-domains = <&pd_a3sp>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof1: spi@e6e10000 { + compatible = "renesas,msiof-sh73a0", "renesas,sh-mobile-msiof"; + reg = <0xe6e10000 0x0064>; + interrupts = <0 77 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks SH73A0_CLK_MSIOF1>; + power-domains = <&pd_a3sp>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof2: spi@e6e00000 { + compatible = "renesas,msiof-sh73a0", "renesas,sh-mobile-msiof"; + reg = <0xe6e00000 0x0064>; + interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks SH73A0_CLK_MSIOF2>; + power-domains = <&pd_a3sp>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof3: spi@e6c90000 { + compatible = "renesas,msiof-sh73a0", "renesas,sh-mobile-msiof"; + reg = <0xe6c90000 0x0064>; + interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks SH73A0_CLK_MSIOF3>; + power-domains = <&pd_a3sp>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sdhi0: sd@ee100000 { compatible = "renesas,sdhi-sh73a0"; reg = <0xee100000 0x100>; -- cgit v1.2.3 From afd7d66c240ba734740b1b4daccd8b1cc735b788 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sun, 29 Nov 2015 11:03:09 +0800 Subject: ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes This adds the supported PRCM clocks and reset controls to the A80 dtsi. The DAUDIO module clocks are not supported yet. Also update clock and reset phandles for r_uart. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 79 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 78 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index 1118bf5cc4fb..a4ce348c0831 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -164,6 +164,14 @@ "usb_phy2", "usb_hsic_12M"; }; + pll3: clk@06000008 { + /* placeholder until implemented */ + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-rate = <0>; + clock-output-names = "pll3"; + }; + pll4: clk@0600000c { #clock-cells = <0>; compatible = "allwinner,sun9i-a80-pll4-clk"; @@ -350,6 +358,68 @@ "apb1_uart2", "apb1_uart3", "apb1_uart4", "apb1_uart5"; }; + + cpus_clk: clk@08001410 { + compatible = "allwinner,sun9i-a80-cpus-clk"; + reg = <0x08001410 0x4>; + #clock-cells = <0>; + clocks = <&osc32k>, <&osc24M>, <&pll4>, <&pll3>; + clock-output-names = "cpus"; + }; + + ahbs: ahbs_clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + clock-div = <1>; + clock-mult = <1>; + clocks = <&cpus_clk>; + clock-output-names = "ahbs"; + }; + + apbs: clk@0800141c { + compatible = "allwinner,sun8i-a23-apb0-clk"; + reg = <0x0800141c 0x4>; + #clock-cells = <0>; + clocks = <&ahbs>; + clock-output-names = "apbs"; + }; + + apbs_gates: clk@08001428 { + compatible = "allwinner,sun9i-a80-apbs-gates-clk"; + reg = <0x08001428 0x4>; + #clock-cells = <1>; + clocks = <&apbs>; + clock-indices = <0>, <1>, + <2>, <3>, + <4>, <5>, + <6>, <7>, + <12>, <13>, + <16>, <17>, + <18>, <20>; + clock-output-names = "apbs_pio", "apbs_ir", + "apbs_timer", "apbs_rsb", + "apbs_uart", "apbs_1wire", + "apbs_i2c0", "apbs_i2c1", + "apbs_ps2_0", "apbs_ps2_1", + "apbs_dma", "apbs_i2s0", + "apbs_i2s1", "apbs_twd"; + }; + + r_1wire_clk: clk@08001450 { + reg = <0x08001450 0x4>; + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + clocks = <&osc32k>, <&osc24M>; + clock-output-names = "r_1wire"; + }; + + r_ir_clk: clk@08001454 { + reg = <0x08001454 0x4>; + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + clocks = <&osc32k>, <&osc24M>; + clock-output-names = "r_ir"; + }; }; soc { @@ -764,13 +834,20 @@ interrupts = ; }; + apbs_rst: reset@080014b0 { + reg = <0x080014b0 0x4>; + compatible = "allwinner,sun6i-a31-clock-reset"; + #reset-cells = <1>; + }; + r_uart: serial@08002800 { compatible = "snps,dw-apb-uart"; reg = <0x08002800 0x400>; interrupts = ; reg-shift = <2>; reg-io-width = <4>; - clocks = <&osc24M>; + clocks = <&apbs_gates 4>; + resets = <&apbs_rst 4>; status = "disabled"; }; }; -- cgit v1.2.3 From d255abd60e9c0c91e0146fdcbe534b3b9f5352a6 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sun, 29 Nov 2015 11:03:10 +0800 Subject: ARM: dts: sun9i: Add TODO comments for the main and low power clocks The main (24MHz) clock on the A80 is configurable via the PRCM address space. The low power/speed (32kHz) clock is from an external chip, the AC100. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index a4ce348c0831..eb69a62f6bc4 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -128,6 +128,17 @@ */ ranges = <0 0 0 0x20000000>; + /* + * This clock is actually configurable from the PRCM address + * space. The external 24M oscillator can be turned off, and + * the clock switched to an internal 16M RC oscillator. Under + * normal operation there's no reason to do this, and the + * default is to use the external good one, so just model this + * as a fixed clock. Also it is not entirely clear if the + * osc24M mux in the PRCM affects the entire clock tree, which + * would also throw all the PLL clock rates off, or just the + * downstream clocks in the PRCM. + */ osc24M: osc24M_clk { #clock-cells = <0>; compatible = "fixed-clock"; @@ -135,6 +146,13 @@ clock-output-names = "osc24M"; }; + /* + * The 32k clock is from an external source, normally the + * AC100 codec/RTC chip. This clock is by default enabled + * and clocked at 32768 Hz, from the oscillator connected + * to the AC100. It is configurable, but no such driver or + * bindings exist yet. + */ osc32k: osc32k_clk { #clock-cells = <0>; compatible = "fixed-clock"; -- cgit v1.2.3 From 1ac56a6da9e11fe35470f804376a67b5bb9d13fe Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:20 +0800 Subject: ARM: dts: sun9i: Add A80 R_PIO pin controller device node The A80 has a secondary pin controller. Add a device node for it. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index eb69a62f6bc4..d02ee5d520e2 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -868,5 +868,19 @@ resets = <&apbs_rst 4>; status = "disabled"; }; + + r_pio: pinctrl@08002c00 { + compatible = "allwinner,sun9i-a80-r-pinctrl"; + reg = <0x08002c00 0x400>; + interrupts = , + ; + clocks = <&apbs_gates 0>; + resets = <&apbs_rst 0>; + gpio-controller; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + #gpio-cells = <3>; + }; }; }; -- cgit v1.2.3 From d2118f06d10886513ca0f462afc8e5263d01692e Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:21 +0800 Subject: ARM: dts: sun9i: optimus: Enable LED3 LED3 is connected to pin PM15 on R_PIO. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-optimus.dts | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index 6ce4b5e8b615..ae7db9fcb2a7 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -65,7 +65,7 @@ leds { compatible = "gpio-leds"; pinctrl-names = "default"; - pinctrl-0 = <&led_pins_optimus>; + pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>; /* The LED names match those found on the board */ @@ -74,7 +74,10 @@ gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; }; - /* led3 is on PM15, in R_PIO */ + led3 { + label = "optimus:led3:usr"; + gpios = <&r_pio 1 15 GPIO_ACTIVE_HIGH>; /* PM15 */ + }; led4 { label = "optimus:led4:usr"; @@ -180,6 +183,15 @@ status = "okay"; }; +&r_pio { + led_r_pins_optimus: led-pins@1 { + allwinner,pins = "PM15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.3 From 1595b37cb212242791dd4ac9334242d32c8ad2c5 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:22 +0800 Subject: ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings The Allwinner A80 SoC has a consumer IR receiver, which is the same as older SoCs. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index d02ee5d520e2..80777a33ee78 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -858,6 +858,18 @@ #reset-cells = <1>; }; + r_ir: ir@08002000 { + compatible = "allwinner,sun5i-a13-ir"; + interrupts = ; + pinctrl-names = "default"; + pinctrl-0 = <&r_ir_pins>; + clocks = <&apbs_gates 1>, <&r_ir_clk>; + clock-names = "apb", "ir"; + resets = <&apbs_rst 1>; + reg = <0x08002000 0x40>; + status = "disabled"; + }; + r_uart: serial@08002800 { compatible = "snps,dw-apb-uart"; reg = <0x08002800 0x400>; @@ -881,6 +893,13 @@ #address-cells = <1>; #size-cells = <0>; #gpio-cells = <3>; + + r_ir_pins: r_ir { + allwinner,pins = "PL6"; + allwinner,function = "s_cir_rx"; + allwinner,drive = ; + allwinner,pull = ; + }; }; }; }; -- cgit v1.2.3 From 969c9687414335701244a98c9d259d2e918d7e34 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:23 +0800 Subject: ARM: dts: sun9i: optimus: Enable consumer IR receiver The A80 Optimus board has a consumer IR receiver. Enable it in the DT. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-optimus.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index ae7db9fcb2a7..79766e5867cd 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -183,6 +183,10 @@ status = "okay"; }; +&r_ir { + status = "okay"; +}; + &r_pio { led_r_pins_optimus: led-pins@1 { allwinner,pins = "PM15"; -- cgit v1.2.3 From ed473ebd9c15481669bfcc1058c6b9bba64ecd12 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:24 +0800 Subject: ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi This patch adds a device node for the Reduced Serial Bus (RSB) controller and the defacto pinmux setting to the A80 dtsi. Since there is only one possible pinmux setting for RSB, just set it in the dtsi. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index 80777a33ee78..dc666c69f6ab 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -900,6 +900,27 @@ allwinner,drive = ; allwinner,pull = ; }; + + r_rsb_pins: r_rsb { + allwinner,pins = "PN0", "PN1"; + allwinner,function = "s_rsb"; + allwinner,drive = ; + allwinner,pull = ; + }; + }; + + r_rsb: i2c@08003400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x08003400 0x400>; + interrupts = ; + clocks = <&apbs_gates 3>; + clock-frequency = <3000000>; + resets = <&apbs_rst 3>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; }; }; }; -- cgit v1.2.3 From a87b5ba9dc2d356cf8e121aeef84f5741a662038 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Tue, 1 Dec 2015 13:47:25 +0800 Subject: ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-optimus.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index 79766e5867cd..c0060e4f7379 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -196,6 +196,10 @@ }; }; +&r_rsb { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.3 From 8ff3b9b40c3f85892e8e6c5b43b1c6ce77400275 Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Fri, 13 Feb 2015 11:41:43 +0800 Subject: ARM: dts: rockchip: update the thermal management on rk3288 In some cases the machine radiating is very poor,sometime the temperature is rising very quickly on heavy loading.So we need have more frequent polling and better granularity. Signed-off-by: Caesar Wang Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-thermal.dtsi | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/rk3288-thermal.dtsi b/arch/arm/boot/dts/rk3288-thermal.dtsi index 340406652186..651b962e3d53 100644 --- a/arch/arm/boot/dts/rk3288-thermal.dtsi +++ b/arch/arm/boot/dts/rk3288-thermal.dtsi @@ -52,7 +52,7 @@ reserve_thermal: reserve_thermal { }; cpu_thermal: cpu_thermal { - polling-delay-passive = <1000>; /* milliseconds */ + polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ thermal-sensors = <&tsadc 1>; @@ -63,6 +63,11 @@ cpu_thermal: cpu_thermal { hysteresis = <2000>; /* millicelsius */ type = "passive"; }; + cpu_alert1: cpu_alert1 { + temperature = <75000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; cpu_crit: cpu_crit { temperature = <90000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ @@ -73,6 +78,11 @@ cpu_thermal: cpu_thermal { cooling-maps { map0 { trip = <&cpu_alert0>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT 6>; + }; + map1 { + trip = <&cpu_alert1>; cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; @@ -80,7 +90,7 @@ cpu_thermal: cpu_thermal { }; gpu_thermal: gpu_thermal { - polling-delay-passive = <1000>; /* milliseconds */ + polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ thermal-sensors = <&tsadc 2>; -- cgit v1.2.3 From 97cb9ce91decfb722255122f37b403145f2ddbb4 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Mon, 30 Nov 2015 13:17:37 +0100 Subject: ARM: dts: rockchip: override thermal settings on veyron-speedy According to a commit on the ChromeOS kernel, the temperature of the Speedy surface is over skin temperature spec. So adjust the thermal settings to mimic the ChromeOS tree to stay within these spec limits. Signed-off-by: Heiko Stuebner Reviewed-by: Caesar Wang --- arch/arm/boot/dts/rk3288-veyron-speedy.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-veyron-speedy.dts b/arch/arm/boot/dts/rk3288-veyron-speedy.dts index a7ea7d06cf7f..b34a7b5b3f62 100644 --- a/arch/arm/boot/dts/rk3288-veyron-speedy.dts +++ b/arch/arm/boot/dts/rk3288-veyron-speedy.dts @@ -88,6 +88,14 @@ }; }; +&cpu_alert0 { + temperature = <65000>; +}; + +&cpu_alert1 { + temperature = <70000>; +}; + &rk808 { pinctrl-names = "default"; pinctrl-0 = <&pmic_int_l>; -- cgit v1.2.3 From 2f23cda3bfa5820fd3702dff45453af4420f7ada Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 13 Nov 2015 15:00:03 +0100 Subject: ARM: ux500: configure the sensors on the TVK board correctly The U8500 HREF TVK board actually has a large set of sensors, with their interrupt lines connected using open drain electronics. Configure the two accelerometers and two magnetometers so we get all sensors to actually probe on boot. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 50 +++++++++++++++++++++++++----- 1 file changed, 43 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 3228119f91d1..b7b4211c5353 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -104,13 +104,40 @@ <19 IRQ_TYPE_EDGE_RISING>; }; lsm303dlh@1e { - /* Magnetometer */ + /* + * This magnetometer is packaged with + * the accelerometer, and has a DRDY line, + * however it is not connected on this + * board so it can not generate interrupts. + */ compatible = "st,lsm303dlh-magn"; reg = <0x1e>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + }; + lis331dl@1c { + /* Accelerometer */ + compatible = "st,lis331dl-accel"; + st,drdy-int-pin = <1>; + reg = <0x1c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + }; + ak8974@0f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; pinctrl-names = "default"; - pinctrl-0 = <&magneto_tvk_mode>; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; }; l3g4200d@68 { /* Gyroscope */ @@ -119,6 +146,10 @@ reg = <0x68>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; }; lsp001wm@5c { /* Barometer/pressure sensor */ @@ -159,17 +190,22 @@ /* Accelerometer interrupt lines 1 & 2 */ tvk_cfg { pins = "GPIO82_C1", "GPIO83_D3"; - ste,config = <&gpio_in_pu>; + ste,config = <&gpio_in_pd>; }; }; }; - magnetometer { - magneto_tvk_mode: magneto_tvk { - /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ + gyroscope { + /* + * These lines are shared between Gyroscope l3g400dh + * and AK8974 magnetometer. + */ + gyro_magn_tvk_mode: gyro_magn_tvk { + /* GPIO 31 used for INT pull down the line */ tvk_cfg1 { pins = "GPIO31_V3"; - ste,config = <&gpio_in_pu>; + ste,config = <&gpio_in_pd>; }; + /* GPIO 32 used for DRDY, pull this down */ tvk_cfg2 { pins = "GPIO32_V2"; ste,config = <&gpio_in_pd>; -- cgit v1.2.3 From e05edea4aa21eb23e712802f63f57fb2c4781c1b Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Thu, 19 Nov 2015 12:31:02 +0530 Subject: ARM: dts: am4372: add spi alias for qspi Set the alias for qspi to spi0 Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am4372.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 1695b684e29d..fda655c252f5 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -30,6 +30,7 @@ serial5 = &uart5; ethernet0 = &cpsw_emac0; ethernet1 = &cpsw_emac1; + spi0 = &qspi; }; cpus { -- cgit v1.2.3 From 317d15679a5e8f970159153111467d361d8944d6 Mon Sep 17 00:00:00 2001 From: Vignesh R Date: Thu, 26 Nov 2015 14:01:26 +0530 Subject: ARM: dts: dra72-evm: Mark uart1 rxd as wakeup capable Uart1 rxd is wakeup capable on DRA72 EVM. Hence, mark rxd line as wakeup capable. This is similar to commit 66b0436977e2c ("ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable") for DRA74 EVM. Signed-off-by: Vignesh R Acked-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra72-evm.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index e5cc5d307f97..ae3502a0267d 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -478,6 +478,8 @@ &uart1 { status = "okay"; + interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, + <&dra7_pmx_core 0x3e0>; }; &elm { -- cgit v1.2.3 From 67e1cbfbc14ab07d0aeffa8d2c92141da32b56e9 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Thu, 3 Dec 2015 16:20:13 +0800 Subject: ARM: dts: sun9i: Add NMI controller device node The Allwinner A80 SoC has an NMI controller. NMI is an external interrupt pin exclusely used with PMICs and other system critical peripherals (such as RTC) in Allwinner's reference designs. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index dc666c69f6ab..e838f206f2a0 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -858,6 +858,14 @@ #reset-cells = <1>; }; + nmi_intc: interrupt-controller@080015a0 { + compatible = "allwinner,sun9i-a80-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x080015a0 0xc>; + interrupts = ; + }; + r_ir: ir@08002000 { compatible = "allwinner,sun5i-a13-ir"; interrupts = ; -- cgit v1.2.3 From ba5810ab0c84069a73b4cd30582c77568158635f Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Mon, 30 Nov 2015 14:23:17 +0100 Subject: ARM: dts: rockchip: make sure edp_24m is associated to xin24m on veyron The edp-24m clock has two possible sources: the 24MHz oscillator as well as an external 27MHz input. The power-on-default is the 27MHz clock which is not supplied on all Rockchip boards. While on all current boards and also all Veyron Chromebooks the bootloader seems to adapt the muxing to the internal source, this doesn't seem to be the case on headless veyron devices like brain and mickey making the edp-24m clock an orphan. On the hardware side the 27m input also is not connected at all. With the upcoming deferral of orphan-clocks this results in the power- domain code deferring, as it cannot request the needed clock and if the synchronous reset is sucessfullat all in this case is also unknown. So fix that by making sure, the edp-24m clock is muxed to the internal 24MHz oscillator at all times. Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-veyron.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rk3288-veyron.dtsi index 5e61f07724d4..9fce91ffff6f 100644 --- a/arch/arm/boot/dts/rk3288-veyron.dtsi +++ b/arch/arm/boot/dts/rk3288-veyron.dtsi @@ -340,6 +340,11 @@ i2c-scl-rising-time-ns = <1000>; }; +&power { + assigned-clocks = <&cru SCLK_EDP_24M>; + assigned-clock-parents = <&xin24m>; +}; + &pwm1 { status = "okay"; }; -- cgit v1.2.3 From 6ea78309ad3ef6bbc6da69da7357d23d15c21fd5 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Mon, 30 Nov 2015 15:29:11 +0100 Subject: ARM: dts: rockchip: add veyron-brain board Similar to pinky, brain is a development model and probably also nearing extinction. But to keep pinky from being lonely I'll keep the two brain boards around as well, especially as they as well have easily accessible dut-connectors. Signed-off-by: Heiko Stuebner For the license change: Acked-by: Brian Norris --- Documentation/devicetree/bindings/arm/rockchip.txt | 5 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3288-veyron-brain.dts | 139 +++++++++++++++++++++ 3 files changed, 145 insertions(+) create mode 100644 arch/arm/boot/dts/rk3288-veyron-brain.dts diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 8e985dd2f181..2f8b35ada4ce 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -35,6 +35,11 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- Google Brain (dev-board): + Required root node properties: + - compatible = "google,veyron-brain-rev0", "google,veyron-brain", + "google,veyron", "rockchip,rk3288"; + - Google Jaq (Haier Chromebook 11 and more): Required root node properties: - compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 87c875247518..2f29350ccce1 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -524,6 +524,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3288-popmetal.dtb \ rk3288-r89.dtb \ rk3288-rock2-square.dtb \ + rk3288-veyron-brain.dtb \ rk3288-veyron-jaq.dtb \ rk3288-veyron-jerry.dtb \ rk3288-veyron-minnie.dtb \ diff --git a/arch/arm/boot/dts/rk3288-veyron-brain.dts b/arch/arm/boot/dts/rk3288-veyron-brain.dts new file mode 100644 index 000000000000..cf5311d2617c --- /dev/null +++ b/arch/arm/boot/dts/rk3288-veyron-brain.dts @@ -0,0 +1,139 @@ +/* + * Google Veyron Brain Rev 0 board device tree source + * + * Copyright 2014 Google, Inc + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-veyron.dtsi" + +/ { + model = "Google Brain"; + compatible = "google,veyron-brain-rev0", "google,veyron-brain", + "google,veyron", "rockchip,rk3288"; + + vcc33_sys: vcc33-sys { + vin-supply = <&vcc_5v>; + }; + + vcc33_io: vcc33_io { + compatible = "regulator-fixed"; + regulator-name = "vcc33_io"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc33_sys>; + /* This is gated by vcc_18 too */ + }; + + /* This turns on vbus for host2 and otg (dwc2) */ + vcc5_host2: vcc5-host2-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_pwr_en>; + regulator-name = "vcc5_host2"; + regulator-always-on; + regulator-boot-on; + }; +}; + +&pinctrl { + hdmi { + vcc50_hdmi_en: vcc50-hdmi-en { + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + dvs_1: dvs-1 { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + dvs_2: dvs-2 { + rockchip,pins = <7 15 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + usb-host { + usb2_pwr_en: usb2-pwr-en { + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&rk808 { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; + + /delete-property/ vcc6-supply; + + regulators { + /* vcc33_io is sourced directly from vcc33_sys */ + /delete-node/ LDO_REG1; + + /* This is not a pwren anymore, but the real power supply */ + vdd10_lcd: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-suspend-mem-disabled; + }; + + vcc18_hdmi: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc18_hdmi"; + regulator-suspend-mem-disabled; + }; + }; +}; + +&vcc50_hdmi { + enable-active-high; + gpio = <&gpio7 2 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc50_hdmi_en>; +}; -- cgit v1.2.3 From 0e1410dda74ef1834916ce60d646ce13cfafb314 Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Tue, 1 Dec 2015 17:03:04 +0100 Subject: ARM: dts: rockchip: add veyron-mickey board Also known as the Asus Chromebit. Signed-off-by: Chris Zhong Tested-by: Caesar Wang For the license change: Acked-by: Brian Norris Signed-off-by: Heiko Stuebner --- Documentation/devicetree/bindings/arm/rockchip.txt | 9 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3288-veyron-mickey.dts | 250 +++++++++++++++++++++ 3 files changed, 260 insertions(+) create mode 100644 arch/arm/boot/dts/rk3288-veyron-mickey.dts diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 2f8b35ada4ce..2fa0a213a0c1 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -54,6 +54,15 @@ Rockchip platforms device tree bindings "google,veyron-jerry-rev3", "google,veyron-jerry", "google,veyron", "rockchip,rk3288"; +- Google Mickey (Asus Chromebit CS10): + Required root node properties: + - compatible = "google,veyron-mickey-rev8", "google,veyron-mickey-rev7", + "google,veyron-mickey-rev6", "google,veyron-mickey-rev5", + "google,veyron-mickey-rev4", "google,veyron-mickey-rev3", + "google,veyron-mickey-rev2", "google,veyron-mickey-rev1", + "google,veyron-mickey-rev0", "google,veyron-mickey", + "google,veyron", "rockchip,rk3288"; + - Google Minnie (Asus Chromebook Flip C100P): Required root node properties: - compatible = "google,veyron-minnie-rev4", "google,veyron-minnie-rev3", diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 2f29350ccce1..8b49bfcbc5d4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -527,6 +527,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3288-veyron-brain.dtb \ rk3288-veyron-jaq.dtb \ rk3288-veyron-jerry.dtb \ + rk3288-veyron-mickey.dtb \ rk3288-veyron-minnie.dtb \ rk3288-veyron-pinky.dtb \ rk3288-veyron-speedy.dtb diff --git a/arch/arm/boot/dts/rk3288-veyron-mickey.dts b/arch/arm/boot/dts/rk3288-veyron-mickey.dts new file mode 100644 index 000000000000..f36f6f459225 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-veyron-mickey.dts @@ -0,0 +1,250 @@ +/* + * Google Veyron Mickey Rev 0 board device tree source + * + * Copyright 2015 Google, Inc + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-veyron.dtsi" + +/ { + model = "Google Mickey"; + compatible = "google,veyron-mickey-rev8", "google,veyron-mickey-rev7", + "google,veyron-mickey-rev6", "google,veyron-mickey-rev5", + "google,veyron-mickey-rev4", "google,veyron-mickey-rev3", + "google,veyron-mickey-rev2", "google,veyron-mickey-rev1", + "google,veyron-mickey-rev0", "google,veyron-mickey", + "google,veyron", "rockchip,rk3288"; + + vcc_5v: vcc-5v { + vin-supply = <&vcc33_sys>; + }; + + vcc33_io: vcc33_io { + compatible = "regulator-fixed"; + regulator-name = "vcc33_io"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc33_sys>; + }; +}; + +&cpu_thermal { + /delete-node/ trips; + /delete-node/ cooling-maps; + + trips { + cpu_alert_almost_warm: cpu_alert_almost_warm { + temperature = <63000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_alert_warm: cpu_alert_warm { + temperature = <65000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_alert_almost_hot: cpu_alert_almost_hot { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_alert_hot: cpu_alert_hot { + temperature = <82000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_alert_hotter: cpu_alert_hotter { + temperature = <84000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_alert_very_hot: cpu_alert_very_hot { + temperature = <85000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + /* + * After 1st level, throttle the CPU down to as low as 1.4 GHz + * and don't let the GPU go faster than 400 MHz. Note that we + * won't throttle the GPU lower than 400 MHz due to CPU + * heat--we'll let the GPU do the rest itself. + */ + cpu_warm_limit_cpu { + trip = <&cpu_alert_warm>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT 4>; + }; + + /* + * Add some discrete steps to help throttling system deal + * with the fact that there are two passive cooling devices: + * the CPU and the GPU. + * + * - 1.2 GHz - 1.0 GHz (almost hot) + * - 800 MHz (hot) + * - 800 MHz - 696 MHz (hotter) + * - 696 MHz - min (very hot) + * + * Note: + * - 800 MHz appears to be a "sweet spot" for me. I can run + * some pretty serious workload here and be happy. + * - After 696 MHz we stop lowering voltage, so throttling + * past there is less effective. + */ + cpu_almost_hot_limit_cpu { + trip = <&cpu_alert_almost_hot>; + cooling-device = + <&cpu0 5 6>; + }; + cpu_hot_limit_cpu { + trip = <&cpu_alert_hot>; + cooling-device = + <&cpu0 7 7>; + }; + cpu_hotter_limit_cpu { + trip = <&cpu_alert_hotter>; + cooling-device = + <&cpu0 7 8>; + }; + cpu_very_hot_limit_cpu { + trip = <&cpu_alert_very_hot>; + cooling-device = + <&cpu0 8 THERMAL_NO_LIMIT>; + }; + }; +}; + +&emmc { + /delete-property/mmc-hs200-1_8v; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c4 { + status = "disabled"; +}; + +&i2s { + status = "okay"; + clock-names = "i2s_hclk", "i2s_clk", "i2s_clk_out"; + clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>, <&cru SCLK_I2S0_OUT>; +}; + +&rk808 { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; + + /delete-property/ vcc6-supply; + /delete-property/ vcc12-supply; + + vcc11-supply = <&vcc33_sys>; + + regulators { + /* vcc33_io is sourced directly from vcc33_sys */ + /delete-node/ LDO_REG1; + /delete-node/ LDO_REG7; + + /* This is not a pwren anymore, but the real power supply */ + vdd10_lcd: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-suspend-mem-disabled; + }; + + vcc18_lcd: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-suspend-mem-disabled; + }; + }; +}; + +&pinctrl { + hdmi { + power_hdmi_on: power-hdmi-on { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + dvs_1: dvs-1 { + rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + dvs_2: dvs-2 { + rockchip,pins = <7 15 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; + +&usb_host0_ehci { + status = "disabled"; +}; + +&usb_host1 { + status = "disabled"; +}; + +&vcc50_hdmi { + enable-active-high; + gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&power_hdmi_on>; +}; -- cgit v1.2.3 From 0560d7c678ae9f4c67b7480f9a42a72c0655c5c5 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Wed, 2 Dec 2015 19:00:02 +0100 Subject: ARM: dts: rockchip: add touchscreen node to veyron minnie Minnie provides an elan,ekth3500 touchscreen over the display, so add the necessary node to enable it. Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-veyron-minnie.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-veyron-minnie.dts b/arch/arm/boot/dts/rk3288-veyron-minnie.dts index 8fd8ef2c72da..e999df74c19a 100644 --- a/arch/arm/boot/dts/rk3288-veyron-minnie.dts +++ b/arch/arm/boot/dts/rk3288-veyron-minnie.dts @@ -117,6 +117,18 @@ clock-frequency = <400000>; i2c-scl-falling-time-ns = <50>; i2c-scl-rising-time-ns = <300>; + + touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + interrupt-parent = <&gpio2>; + interrupts = <14 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&touch_int &touch_rst>; + reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; + vcc33-supply = <&vcc33_touch>; + vccio-supply = <&vcc33_touch>; + }; }; &rk808 { -- cgit v1.2.3 From 686c47f1300534439fd550e4cbfe1776abceab5a Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:54:56 +0200 Subject: ARM: dts: am437x: cm-t43: add basic support for sbc-t43 Add basic support for SBC-T43: a CM-T43 based single board computer. CM-T43 is an AM437x based System-on-Module designed to serve as a building block in embedded applications. SBC-T43 is composed of CM-T43 module on top of the SB-SOM-T43 baseboard. Basic support includes UART, GPIO, and I2C. Signed-off-by: Nikita Kiryanov Acked-by: Rob Herring Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/omap/omap.txt | 6 ++ arch/arm/boot/dts/Makefile | 6 +- arch/arm/boot/dts/am437x-cm-t43.dts | 90 ++++++++++++++++++++++ arch/arm/boot/dts/am437x-sbc-t43.dts | 56 ++++++++++++++ 4 files changed, 156 insertions(+), 2 deletions(-) create mode 100644 arch/arm/boot/dts/am437x-cm-t43.dts create mode 100644 arch/arm/boot/dts/am437x-sbc-t43.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 2154f9797714..f003741320af 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -144,6 +144,12 @@ Boards: - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" +- AM437x CM-T43 + compatible = "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + +- AM437x SBC-T43 + compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + - AM43x EPOS EVM compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 518db314b039..79bd9764d9b6 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -480,9 +480,11 @@ dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-var-stk-om44.dtb dtb-$(CONFIG_SOC_AM43XX) += \ am43x-epos-evm.dtb \ - am437x-sk-evm.dtb \ + am437x-cm-t43.dtb \ + am437x-gp-evm.dtb \ am437x-idk-evm.dtb \ - am437x-gp-evm.dtb + am437x-sbc-t43.dtb \ + am437x-sk-evm.dtb dtb-$(CONFIG_SOC_OMAP5) += \ omap5-cm-t54.dtb \ omap5-igep0050.dtb \ diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts new file mode 100644 index 000000000000..a131b971315e --- /dev/null +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -0,0 +1,90 @@ +/* + * Copyright (C) 2015 CompuLab, Ltd. - http://www.compulab.co.il/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include +#include +#include +#include "am4372.dtsi" + +/ { + model = "CompuLab CM-T43"; + compatible = "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"; + + leds { + compatible = "gpio-leds"; + + ledb { + label = "cm-t43:green"; + gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&am43xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&cm_t43_led_pins>; + + cm_t43_led_pins: cm_t43_led_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0xa78, MUX_MODE7) + >; + }; + + i2c0_pins: i2c0_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <100000>; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&gpio4 { + status = "okay"; +}; + +&gpio5 { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&cpu { + operating-points = <1000000 1330000>, + <800000 1260000>, + <720000 1200000>, + <600000 1100000>, + <300000 950000>; +}; diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts new file mode 100644 index 000000000000..6ca22b76d1bd --- /dev/null +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -0,0 +1,56 @@ +/* + * Copyright (C) 2015 CompuLab, Ltd. - http://www.compulab.co.il/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am437x-cm-t43.dts" + +/ { + model = "CompuLab CM-T43 on SB-SOM-T43"; + compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"; +}; + +&am43xx_pinmux { + uart0_pins_default: uart0_pins_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) + AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) + AM4372_IOPAD(0x970, PIN_INPUT_PULLUP | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM4372_IOPAD(0x974, PIN_INPUT | PULL_DISABLE | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + i2c1_pins: i2c1_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0xa6c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE1) /* spi2_cs0.i2c1_sda */ + AM4372_IOPAD(0xa60, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE1) /* spi2_sclk.i2c1_scl */ + >; + }; + + i2c2_pins: i2c2_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + >; + }; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_default>; +}; -- cgit v1.2.3 From 989d21ec7986955f27a7b8e5c0a2c2d358f88223 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:54:57 +0200 Subject: ARM: dts: am437x: cm-t43: add support for module eeprom CM-T43 has an on-board EEPROM on i2c bus 0. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index a131b971315e..ce33b416a5b9 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -51,6 +51,12 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; clock-frequency = <100000>; + + eeprom_module: at24@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; }; &gpio0 { -- cgit v1.2.3 From 4bbbd23c05f8ae99c4e7705585b4b9d6ff97806e Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:54:58 +0200 Subject: ARM: dts: am437x: cm-t43: add PMIC support. Add PMIC support for CompuLab cm-t43 module. For now we keep all regulators enabled until this could be refined with power management support. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 64 +++++++++++++++++++++++++++++++++++++ 1 file changed, 64 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index ce33b416a5b9..27b748a763d3 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -52,6 +52,69 @@ pinctrl-0 = <&i2c0_pins>; clock-frequency = <100000>; + tps65218: tps65218@24 { + compatible = "ti,tps65218"; + reg = <0x24>; + interrupts = ; /* NMIn */ + interrupt-parent = <&gic>; + interrupt-controller; + #interrupt-cells = <2>; + + dcdc1: regulator-dcdc1 { + compatible = "ti,tps65218-dcdc1"; + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2: regulator-dcdc2 { + compatible = "ti,tps65218-dcdc2"; + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1378000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3: regulator-dcdc3 { + compatible = "ti,tps65218-dcdc3"; + regulator-name = "vdcdc3"; + regulator-suspend-enable; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc5: regulator-dcdc5 { + compatible = "ti,tps65218-dcdc5"; + regulator-name = "v1_0bat"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc6: regulator-dcdc6 { + compatible = "ti,tps65218-dcdc6"; + regulator-name = "v1_8bat"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: regulator-ldo1 { + compatible = "ti,tps65218-ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + eeprom_module: at24@50 { compatible = "atmel,24c02"; reg = <0x50>; @@ -88,6 +151,7 @@ }; &cpu { + cpu0-supply = <&dcdc2>; operating-points = <1000000 1330000>, <800000 1260000>, <720000 1200000>, -- cgit v1.2.3 From 81fb61fc2e3cd66223a79287cbb6bf410ae7af80 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:54:59 +0200 Subject: ARM: dts: am437x: cm-t43: add spi-flash support CM-T43 has an on-board 2MB SPI-flash which stores U-Boot and the U-Boot environment. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 40 +++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index 27b748a763d3..27e594823867 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -44,6 +44,15 @@ AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; + + spi0_pins: pinmux_spi0_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0) /* spi0_sclk.spi0_sclk */ + AM4372_IOPAD(0x954, PIN_INPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */ + AM4372_IOPAD(0x958, PIN_OUTPUT | MUX_MODE0) /* spi0_d1.spi0_d1 */ + AM4372_IOPAD(0x95C, PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + >; + }; }; &i2c0 { @@ -146,6 +155,37 @@ status = "okay"; }; +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + dmas = <&edma 16 + &edma 17>; + dma-names = "tx0", "rx0"; + + flash: w25q64cvzpig@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + partition@0 { + label = "uboot"; + reg = <0x0 0xc0000>; + }; + + partition@c0000 { + label = "uboot environment"; + reg = <0xc0000 0x40000>; + }; + + partition@100000 { + label = "reserved"; + reg = <0x100000 0x100000>; + }; + }; +}; + &uart0 { status = "okay"; }; -- cgit v1.2.3 From 3edac2f8e34192fe18841d1ef4fadd8043e21029 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:00 +0200 Subject: ARM: dts: am437x: cm-t43: add NAND support One of the CompuLab cm-t43 configurations comes with on-board NAND flash as primary storage. It is partitioned into kernel, dtb, and rootfs partitions. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 79 +++++++++++++++++++++++++++++++++++++ 1 file changed, 79 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index 27e594823867..efabb31d33d1 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -53,6 +53,81 @@ AM4372_IOPAD(0x95C, PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ >; }; + + nand_flash_x8: nand_flash_x8 { + pinctrl-single,pins = < + AM4372_IOPAD(0x800, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x804, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x808, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x80c, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x810, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x814, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x818, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x81c, PIN_INPUT | PULL_DISABLE | MUX_MODE0) + AM4372_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x898, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM4372_IOPAD(0x894, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM4372_IOPAD(0x890, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + AM4372_IOPAD(0x89c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + >; + }; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_flash_x8>; + ranges = <0 0 0x08000000 0x1000000>; + nand@0,0 { + reg = <0 0 0>; + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + gpmc,wait-pin = <0>; + + #address-cells = <1>; + #size-cells = <1>; + /* MTD partition table */ + partition@0 { + label = "kernel"; + reg = <0x0 0x00980000>; + }; + partition@980000 { + label = "dtb"; + reg = <0x00980000 0x00080000>; + }; + partition@a00000 { + label = "rootfs"; + reg = <0x00a00000 0x0>; + }; + }; }; &i2c0 { @@ -186,6 +261,10 @@ }; }; +&elm { + status = "okay"; +}; + &uart0 { status = "okay"; }; -- cgit v1.2.3 From 4b4959af13cec19f0aa5c8f6b56f9c5d0e736103 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:01 +0200 Subject: ARM: dts: am437x: cm-t43: add dual emac support CM-T43 comes with 2 ethernet ports connected to the cpsw subsystem, which has 2 modes of operation: switch mode and dual emac mode. Add the relevant muxing and set it up to work in dual emac mode by default. Signed-off-by: Nikita Kiryanov Acked-by: Mugunthan V N Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 66 +++++++++++++++++++++++++++++++++++++ 1 file changed, 66 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index efabb31d33d1..fd97a892c7d5 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -73,6 +73,47 @@ AM4372_IOPAD(0x89c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) >; }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_txen */ + AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rxctl */ + AM4372_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd3 */ + AM4372_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd2 */ + AM4372_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd1 */ + AM4372_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd0 */ + AM4372_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ + AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ + AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd3 */ + AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd2 */ + AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ + AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ + AM4372_IOPAD(0xa74, MUX_MODE3) + /* Slave 2 */ + AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.txen */ + AM4372_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rxctl */ + AM4372_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.txd3 */ + AM4372_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.txd2 */ + AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.txd1 */ + AM4372_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.txd0 */ + AM4372_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.tclk */ + AM4372_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rclk */ + AM4372_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rxd3 */ + AM4372_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rxd2 */ + AM4372_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rxd1 */ + AM4372_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rxd0 */ + AM4372_IOPAD(0xa38, MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM4372_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; }; &gpmc { @@ -261,6 +302,31 @@ }; }; +&mac { + pinctrl-names = "default"; + pinctrl-0 = <&cpsw_default>; + dual_emac = <1>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&davinci_mdio_default>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + dual_emac_res_vlan = <1>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + dual_emac_res_vlan = <2>; +}; + &elm { status = "okay"; }; -- cgit v1.2.3 From 9fc830b0371cb3c363e24fb1e3d6fb883e20eca1 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:02 +0200 Subject: ARM: dts: am437x: cm-t43: add USB support Add USB support for CompuLab sbc-t43 single board computer, defaulting to host mode. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 30 ++++++++++++++++++++++++++++++ arch/arm/boot/dts/am437x-sbc-t43.dts | 22 ++++++++++++++++++++++ 2 files changed, 52 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index fd97a892c7d5..a2893c6950d1 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -327,6 +327,36 @@ dual_emac_res_vlan = <2>; }; +&dwc3_1 { + status = "okay"; +}; + +&usb2_phy1 { + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + status = "okay"; +}; + +&dwc3_2 { + status = "okay"; +}; + +&usb2_phy2 { + status = "okay"; +}; + +&usb2 { + dr_mode = "host"; + status = "okay"; + interrupts = , + , + ; + interrupt-names = "peripheral", "host", "otg"; +}; + &elm { status = "okay"; }; diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts index 6ca22b76d1bd..3fc824a5b13c 100644 --- a/arch/arm/boot/dts/am437x-sbc-t43.dts +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -36,6 +36,18 @@ AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ >; }; + + usb2_phy1_default: usb2_phy1_default { + pinctrl-single,pins = < + AM4372_IOPAD(0xac0, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE0) + >; + }; + + usb2_phy2_default: usb2_phy2_default { + pinctrl-single,pins = < + AM4372_IOPAD(0xac4, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE0) + >; + }; }; &i2c1 { @@ -54,3 +66,13 @@ pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_default>; }; + +&dwc3_1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb2_phy1_default>; +}; + +&dwc3_2 { + pinctrl-names = "default"; + pinctrl-0 = <&usb2_phy2_default>; +}; -- cgit v1.2.3 From e7f83e8f3d685aa9df075a117021b298395156b5 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:03 +0200 Subject: ARM: dts: am437x: cm-t43: add eMMC support One of the CompuLab cm-t43 configurations comes with on-board eMMC as primary storage, residing on the mmc2 interface. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index a2893c6950d1..1011accb56e6 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -26,6 +26,15 @@ linux,default-trigger = "heartbeat"; }; }; + + vmmc_3v3: fixedregulator-v3_3 { + compatible = "regulator-fixed"; + regulator-name = "vmmc_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + enable-active-high; + }; }; &am43xx_pinmux { @@ -45,6 +54,21 @@ >; }; + emmc_pins: emmc_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad8.mmc1_dat0 */ + AM4372_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad9.mmc1_dat1 */ + AM4372_IOPAD(0x828, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad10.mmc1_dat2 */ + AM4372_IOPAD(0x82c, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad11.mmc1_dat3 */ + AM4372_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad12.mmc1_dat4 */ + AM4372_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad13.mmc1_dat5 */ + AM4372_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad14.mmc1_dat6 */ + AM4372_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad15.mmc1_dat7 */ + AM4372_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM4372_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + >; + }; + spi0_pins: pinmux_spi0_pins { pinctrl-single,pins = < AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0) /* spi0_sclk.spi0_sclk */ @@ -271,6 +295,15 @@ status = "okay"; }; +&mmc2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + vmmc-supply = <&vmmc_3v3>; + bus-width = <8>; + ti,non-removable; +}; + &spi0 { status = "okay"; pinctrl-names = "default"; -- cgit v1.2.3 From a7c787677461829e22698ca001aedfda4ae06651 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:04 +0200 Subject: ARM: dts: am437x: cm-t43: add touchscreen support AM437x has an internal touchscreen controller. Add support for it on cm-t43. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-cm-t43.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts index 1011accb56e6..8677f4cce9e9 100644 --- a/arch/arm/boot/dts/am437x-cm-t43.dts +++ b/arch/arm/boot/dts/am437x-cm-t43.dts @@ -398,6 +398,20 @@ status = "okay"; }; +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; +}; + &cpu { cpu0-supply = <&dcdc2>; operating-points = <1000000 1330000>, -- cgit v1.2.3 From 90f7cf83876a083f9e1c3a9e595bc9acaffb7c29 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:05 +0200 Subject: ARM: dts: am437x: cm-t43: add pca9555 support SB-SOM comes with a PCA9555 GPIO extender. On SBC-T43 this resides on the i2c1 bus. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sbc-t43.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts index 3fc824a5b13c..c7a1414dca2c 100644 --- a/arch/arm/boot/dts/am437x-sbc-t43.dts +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -54,6 +54,13 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; }; &i2c2 { -- cgit v1.2.3 From 07634f12f74bf1c70887b8575970275b1044c9cb Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:06 +0200 Subject: ARM: dts: am437x: cm-t43: add support for baseboard eeprom SB-SOM baseboard comes with an on-board EEPROM. On SBC-T43 this EEPROM resides on the i2c1 bus. Add it to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sbc-t43.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts index c7a1414dca2c..46b28318d91a 100644 --- a/arch/arm/boot/dts/am437x-sbc-t43.dts +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -61,6 +61,12 @@ gpio-controller; #gpio-cells = <2>; }; + + eeprom_base: at24@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; }; &i2c2 { -- cgit v1.2.3 From 02fc7720c627274c66d253c6c4671deec546394a Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:07 +0200 Subject: ARM: dts: sb-som: introduce SB-SOM baseboard CompuLab SB-SOM baseboard is a carrier board for multiple arm-based SoMs. It currently supports (with minor adjustments to assembly) CM-T43, CM-T54, and CM-QS600 modules. It is a building block in the SBC-T43 single board computer, which consists of cm-t43 on top of sb-som-t43. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/compulab-boards.txt | 5 +++ .../display/panel/startek,startek-kd050c.txt | 4 +++ .../devicetree/bindings/vendor-prefixes.txt | 1 + arch/arm/boot/dts/compulab-sb-som.dtsi | 42 ++++++++++++++++++++++ 4 files changed, 52 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/compulab-boards.txt create mode 100644 Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt create mode 100644 arch/arm/boot/dts/compulab-sb-som.dtsi diff --git a/Documentation/devicetree/bindings/arm/compulab-boards.txt b/Documentation/devicetree/bindings/arm/compulab-boards.txt new file mode 100644 index 000000000000..71172d56875c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/compulab-boards.txt @@ -0,0 +1,5 @@ +CompuLab SB-SOM is a multi-module baseboard capable of carrying CM-T43, CM-T54, +and CM-QS600 modules with minor modifications to the SB-SOM assembly. + +Required root node properties: + - compatible = should be "compulab,sb-som" diff --git a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt new file mode 100644 index 000000000000..70cd8d18d841 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt @@ -0,0 +1,4 @@ +Startek Electronic Technology Co. KD050C 5.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "startek,startek-kd050c" diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 55df1d444e9f..409b134b7f88 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -218,6 +218,7 @@ sony Sony Corporation spansion Spansion Inc. sprd Spreadtrum Communications Inc. st STMicroelectronics +startek Startek ste ST-Ericsson stericsson ST-Ericsson synology Synology, Inc. diff --git a/arch/arm/boot/dts/compulab-sb-som.dtsi b/arch/arm/boot/dts/compulab-sb-som.dtsi new file mode 100644 index 000000000000..402a143c85c8 --- /dev/null +++ b/arch/arm/boot/dts/compulab-sb-som.dtsi @@ -0,0 +1,42 @@ +/* + * Copyright (C) 2015 CompuLab, Ltd. - http://www.compulab.co.il/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + model = "CompuLab SB-SOM"; + compatible = "compulab,sb-som"; + + vsb_3v3: fixedregulator-v3_3 { + compatible = "regulator-fixed"; + regulator-name = "vsb_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + enable-active-high; + }; + + lcd0: display { + compatible = "startek,startek-kd050c", "panel-dpi"; + label = "lcd"; + + panel-timing { + clock-frequency = <33000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <43>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; +}; -- cgit v1.2.3 From 97ce5054989983fae5e3dac8c9182875af795260 Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:08 +0200 Subject: ARM: dts: am437x: cm-t43: add support for mmc1 On SBC-T43 the mmc1 interface is connected to an SD-Card slot. Add the necessary muxing and configuration to the device tree. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sbc-t43.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts index 46b28318d91a..6b51151dd7df 100644 --- a/arch/arm/boot/dts/am437x-sbc-t43.dts +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -7,6 +7,7 @@ */ #include "am437x-cm-t43.dts" +#include "compulab-sb-som.dtsi" / { model = "CompuLab CM-T43 on SB-SOM-T43"; @@ -14,6 +15,19 @@ }; &am43xx_pinmux { + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + AM4372_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + AM4372_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + AM4372_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + AM4372_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + AM4372_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + AM4372_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + AM4372_IOPAD(0x964, PIN_INPUT | MUX_MODE7) /* ecap0_in_pwm0_out.gpio0_7 */ + >; + }; + uart0_pins_default: uart0_pins_default { pinctrl-single,pins = < AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) @@ -75,6 +89,16 @@ pinctrl-0 = <&i2c2_pins>; }; +&mmc1 { + status = "okay"; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vsb_3v3>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_default>; -- cgit v1.2.3 From e81bce70eb66d1010721af6b38d343e3ac90476a Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 1 Dec 2015 15:55:09 +0200 Subject: ARM: dts: am437x: cm-t43: add lcd support Add the necessary dss configuration to drive the startek lcd on CompuLab sbc-t43 single board computer. Signed-off-by: Nikita Kiryanov Cc: Tony Lindgren Cc: Benoit Cousson Cc: Rob Herring Cc: Mark Rutland Cc: Pawel Moll Cc: Igor Grinberg Cc: Dmitry Lifshitz Cc: Ian Campbell Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sbc-t43.dts | 65 ++++++++++++++++++++++++++++++++++++ 1 file changed, 65 insertions(+) diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/am437x-sbc-t43.dts index 6b51151dd7df..5f750c0ed6c9 100644 --- a/arch/arm/boot/dts/am437x-sbc-t43.dts +++ b/arch/arm/boot/dts/am437x-sbc-t43.dts @@ -12,6 +12,10 @@ / { model = "CompuLab CM-T43 on SB-SOM-T43"; compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"; + + aliases { + display0 = &lcd0; + }; }; &am43xx_pinmux { @@ -28,6 +32,41 @@ >; }; + dss_pinctrl_default: dss_pinctrl_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE2) /* cam0 hd -> DSS DATA 23 */ + AM4372_IOPAD(0x9b4, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9b8, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9bc, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9c0, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9c4, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9c8, PIN_OUTPUT_PULLUP | MUX_MODE2) + AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE2) /* cam1 data 9 -> DSS DATA 16 */ + + AM4372_IOPAD(0x8a0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */ + AM4372_IOPAD(0x8a4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8a8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8ac, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8b8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8bc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8c8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8cc, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d0, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d4, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8d8, PIN_OUTPUT_PULLUP | MUX_MODE0) + AM4372_IOPAD(0x8dc, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */ + AM4372_IOPAD(0x8e0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */ + AM4372_IOPAD(0x8e4, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */ + AM4372_IOPAD(0x8e8, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */ + AM4372_IOPAD(0x8ec, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */ + AM4372_IOPAD(0xa20, PIN_OUTPUT_PULLUP | MUX_MODE7) + >; + }; + uart0_pins_default: uart0_pins_default { pinctrl-single,pins = < AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) @@ -99,6 +138,20 @@ wp-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; }; +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_pinctrl_default>; + + port { + dpi_lcd_out: endpoint@0 { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_default>; @@ -113,3 +166,15 @@ pinctrl-names = "default"; pinctrl-0 = <&usb2_phy2_default>; }; + +&lcd0 { + enable-gpios = <&pca9555 14 GPIO_ACTIVE_HIGH + &gpio4 28 GPIO_ACTIVE_HIGH>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_lcd_out>; + data-lines = <24>; + }; + }; +}; -- cgit v1.2.3 From 387450fc882ea24462b53e85b89d88a51aafa3aa Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:03 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add basic module support Add support for CompuLab CM-SOM-AM57X board. CL-SOM-AM57x is a miniature System-on-Module (SoM) based on TI Sitara AM57x ARM Cortex-A15 System-on-Chip family. https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/ Add basic DT support for standalone module (without a carrier board): * Memory configuration * Heartbeat led * I2C1 and I2C4 * PMIC * SATA Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/omap/omap.txt | 3 + arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 274 +++++++++++++++++++++ 3 files changed, 279 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am57xx-cl-som-am57x.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f003741320af..1b9cae587707 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -159,6 +159,9 @@ Boards: - AM437x SK EVM: AM437x StarterKit Evaluation Module compatible = "ti,am437x-sk-evm", "ti,am4372", "ti,am43" +- AM57XX CL-SOM-AM57x + compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 79bd9764d9b6..6e9a3af802ab 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -491,8 +491,9 @@ dtb-$(CONFIG_SOC_OMAP5) += \ omap5-sbc-t54.dtb \ omap5-uevm.dtb dtb-$(CONFIG_SOC_DRA7XX) += \ - dra7-evm.dtb \ am57xx-beagle-x15.dtb \ + am57xx-cl-som-am57x.dtb \ + dra7-evm.dtb \ dra72-evm.dtb dtb-$(CONFIG_ARCH_ORION5X) += \ orion5x-lacie-d2-network.dtb \ diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts new file mode 100644 index 000000000000..087d62e49e3c --- /dev/null +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -0,0 +1,274 @@ +/* + * Support for CompuLab CL-SOM-AM57x System-on-Module + * + * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * Author: Dmitry Lifshitz + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ + +/dts-v1/; + +#include +#include +#include "dra74x.dtsi" + +/ { + model = "CompuLab CL-SOM-AM57x"; + compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB - minimal configuration */ + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins_default>; + + led@0 { + label = "cl-som-am57x:green"; + gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; +}; + +&dra7_pmx_core { + leds_pins_default: leds_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x347c, PIN_OUTPUT | MUX_MODE14) /* gpmc_a15.gpio2_5 */ + >; + }; + + i2c1_pins_default: i2c1_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */ + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */ + >; + }; + + i2c4_pins_default: i2c4_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x36ac, PIN_INPUT| MUX_MODE10) /* mcasp1_acl.i2c4_sda */ + DRA7XX_CORE_IOPAD(0x36b0, PIN_INPUT| MUX_MODE10) /* mcasp1_fsr.i2c4_scl */ + >; + }; + + tps659038_pins_default: tps659038_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */ + >; + }; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_default>; + clock-frequency = <400000>; +}; + +&i2c4 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_default>; + clock-frequency = <400000>; + + tps659038: tps659038@58 { + compatible = "ti,tps659038"; + reg = <0x58>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&tps659038_pins_default>; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + + tps659038_pmic { + compatible = "ti,tps659038-pmic"; + + regulators { + smps12_reg: smps12 { + /* VDD_MPU */ + regulator-name = "smps12"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps3_reg: smps3 { + /* VDD_DDR */ + regulator-name = "smps3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_DSPEVE */ + regulator-name = "smps45"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_GPU */ + regulator-name = "smps6"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* VDD_CORE */ + regulator-name = "smps7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1160000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_IVA */ + regulator-name = "smps8"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* PMIC_3V3 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + + ldo1_reg: ldo1 { + /* VDD_SD / VDDSHV8 */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + /* VDD_1V8 */ + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo3_reg: ldo3 { + /* VDDA_1V8_PHYA - supplies VDDA_SATA, VDDA_USB1/2/3 */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + /* VDDA_1V8_PHYB - supplies VDDA_HDMI, VDDA_PCIE/0/1 */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo9_reg: ldo9 { + /* VDD_RTC */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1V8_PLL */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + /* regen1 not used */ + }; + }; + + tps659038_pwr_button: tps659038_pwr_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + ti,palmas-long-press-seconds = <12>; + }; + + tps659038_gpio: tps659038_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; +}; + +&cpu0 { + cpu0-supply = <&smps12_reg>; + voltage-tolerance = <1>; +}; + +&sata { + status = "okay"; +}; + +&mailbox5 { + status = "okay"; + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + status = "okay"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + status = "okay"; + }; +}; + +&mailbox6 { + status = "okay"; + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + status = "okay"; + }; + mbox_dsp2_ipc3x: mbox_dsp2_ipc3x { + status = "okay"; + }; +}; -- cgit v1.2.3 From 1a472e14ba0847a30f8bafeea914b048df5c5d24 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:04 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: dts: add RTC support Add EM3027 RTC chip support (over I2C4 bus). Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 087d62e49e3c..58156a93d6e4 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -242,6 +242,11 @@ #gpio-cells = <2>; }; }; + + rtc0: rtc@56 { + compatible = "emmicro,em3027"; + reg = <0x56>; + }; }; &cpu0 { -- cgit v1.2.3 From 5691b61f23e508085405367573dc6120d1754a24 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:05 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add I2C3 support Enable I2C3 bus and add appropriate pinmux. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 58156a93d6e4..2074fd426242 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -52,6 +52,13 @@ >; }; + i2c3_pins_default: i2c3_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */ + DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */ + >; + }; + i2c4_pins_default: i2c4_pins_default { pinctrl-single,pins = < DRA7XX_CORE_IOPAD(0x36ac, PIN_INPUT| MUX_MODE10) /* mcasp1_acl.i2c4_sda */ @@ -73,6 +80,13 @@ clock-frequency = <400000>; }; +&i2c3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins_default>; + clock-frequency = <400000>; +}; + &i2c4 { status = "okay"; pinctrl-names = "default"; -- cgit v1.2.3 From 2c7cf1f48f36935d3a8e95b2f29774380e51c3f7 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:06 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add EEPROM support On-board EEPROM chip is used for storing a board production info. Add module EEPROM support (over I2C4 bus). Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 2074fd426242..1badfa908ed3 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -261,6 +261,12 @@ compatible = "emmicro,em3027"; reg = <0x56>; }; + + eeprom_module: atmel@50 { + compatible = "atmel,24c08"; + reg = <0x50>; + pagesize = <16>; + }; }; &cpu0 { -- cgit v1.2.3 From 8deb60f535fa76b2dc578e0c33602aeb19b7b30b Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:07 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add eMMC support CM-SOM-AM57X has two options of main storage devices - eMMC or NAND. Add eMMC chip support (over MMC2 bus). Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 34 +++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 1badfa908ed3..ef94845103e3 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -36,6 +36,13 @@ default-state = "off"; }; }; + + vdd_3v3: fixedregulator-vdd_3v3 { + compatible = "regulator-fixed"; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core { @@ -71,6 +78,21 @@ DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */ >; }; + + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; }; &i2c1 { @@ -297,3 +319,15 @@ status = "okay"; }; }; + +&mmc2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + + vmmc-supply = <&vdd_3v3>; + bus-width = <8>; + ti,non-removable; + cap-mmc-dual-data-rate; +}; -- cgit v1.2.3 From cc2d681420d0fc67c362f1245dbb420d1161918e Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:08 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add spi-flash support On-board spi-flash chip is used as a main boot device. Add spi-flash chip support (over QSPI bus). Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 42 +++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index ef94845103e3..f7e163ad6b99 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -93,6 +93,17 @@ DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ >; }; + + qspi1_pins: pinmux_qspi1_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3474, PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ + DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d0 */ + DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d1 */ + DRA7XX_CORE_IOPAD(0x3488, PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ + DRA7XX_CORE_IOPAD(0x34b8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ + DRA7XX_CORE_IOPAD(0x34bc, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ + >; + }; }; &i2c1 { @@ -331,3 +342,34 @@ ti,non-removable; cap-mmc-dual-data-rate; }; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi1_pins>; + + spi-max-frequency = <20000000>; + + spi_flash: spi_flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80", "jedec,spi-nor"; + reg = <0>; /* CS0 */ + spi-max-frequency = <20000000>; + + partition@0 { + label = "uboot"; + reg = <0x0 0xc0000>; + }; + + partition@c0000 { + label = "uboot environment"; + reg = <0xc0000 0x40000>; + }; + + partition@100000 { + label = "reserved"; + reg = <0x100000 0x0>; + }; + }; +}; -- cgit v1.2.3 From 12ca468306a208e28ac465e0083453814e2b7ace Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:09 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add dual EMAC support Add dual EMAC support. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 105 ++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index f7e163ad6b99..fe4baba1872c 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -104,6 +104,85 @@ DRA7XX_CORE_IOPAD(0x34bc, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ >; }; + + cpsw_pins_default: cpsw_pins_default { + pinctrl-single,pins = < + /* Slave at addr 0x0 */ + DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii0_tclk */ + DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii0_tctl */ + DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td3 */ + DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td2 */ + DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td1 */ + DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td0 */ + DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rclk */ + DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rctl */ + DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd3 */ + DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd2 */ + DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd1 */ + DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd0 */ + + /* Slave at addr 0x1 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_tclk */ + DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ + DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ + DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ + DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ + DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + >; + }; + + cpsw_pins_sleep: cpsw_pins_sleep { + pinctrl-single,pins = < + /* Slave 1 */ + DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15) + + /* Slave 2 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15) + >; + }; + + davinci_mdio_pins_default: davinci_mdio_pins_default { + pinctrl-single,pins = < + /* MDIO */ + DRA7XX_CORE_IOPAD(0x3590, PIN_OUTPUT_PULLUP | MUX_MODE3)/* vin2a_d10.mdio_mclk */ + DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d11.mdio_d */ + >; + }; + + davinci_mdio_pins_sleep: davinci_mdio_pins_sleep { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3590, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT | MUX_MODE15) + >; + }; }; &i2c1 { @@ -373,3 +452,29 @@ }; }; }; + +&mac { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_pins_default>; + pinctrl-1 = <&cpsw_pins_sleep>; + dual_emac; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii"; + dual_emac_res_vlan = <0>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii"; + dual_emac_res_vlan = <1>; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_pins_default>; + pinctrl-1 = <&davinci_mdio_pins_sleep>; +}; -- cgit v1.2.3 From 27ddd846cb25851f5624890869c3c193f79d8661 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:10 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add USB support Add USB support. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index fe4baba1872c..c603136ee0a0 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -478,3 +478,19 @@ pinctrl-0 = <&davinci_mdio_pins_default>; pinctrl-1 = <&davinci_mdio_pins_sleep>; }; + +&usb2_phy1 { + phy-supply = <&ldousb_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldousb_reg>; +}; + +&usb1 { + dr_mode = "host"; +}; + +&usb2 { + dr_mode = "peripheral"; +}; -- cgit v1.2.3 From 2d47fc3b9801332a5110c363c2880d78826c668a Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:11 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add touchscreen support Add ADS7846 touchscreen support. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 44 +++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index c603136ee0a0..a75c382dde78 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -43,6 +43,13 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + ads7846reg: fixedregulator-ads7846-reg { + compatible = "regulator-fixed"; + regulator-name = "ads7846-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core { @@ -183,6 +190,12 @@ DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT | MUX_MODE15) >; }; + + ads7846_pins: pinmux_ads7846_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3464, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpmc_a9.gpio1_31 */ + >; + }; }; &i2c1 { @@ -451,6 +464,37 @@ reg = <0x100000 0x0>; }; }; + + /* touch controller */ + ads7846@0 { + pinctrl-names = "default"; + pinctrl-0 = <&ads7846_pins>; + + compatible = "ti,ads7846"; + vcc-supply = <&ads7846reg>; + + reg = <1>; /* CS1 */ + spi-max-frequency = <1500000>; + + interrupt-parent = <&gpio1>; + interrupts = <31 0>; + pendown-gpio = <&gpio1 31 0>; + + + ti,x-min = /bits/ 16 <0x0>; + ti,x-max = /bits/ 16 <0x0fff>; + ti,y-min = /bits/ 16 <0x0>; + ti,y-max = /bits/ 16 <0x0fff>; + + ti,x-plate-ohms = /bits/ 16 <180>; + ti,pressure-max = /bits/ 16 <255>; + + ti,debounce-max = /bits/ 16 <30>; + ti,debounce-tol = /bits/ 16 <10>; + ti,debounce-rep = /bits/ 16 <1>; + + linux,wakeup; + }; }; &mac { -- cgit v1.2.3 From 4424cd009648f45991a7123f6ce383e1d4e7d53e Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:12 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add analog audio support Add analog audio DT nodes: 1. simple-audio-card node 2. wm8731 codec node 3. MCASP3 pinmux Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 67 +++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index a75c382dde78..b2c44515f62d 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -50,6 +50,33 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + sound0: sound@0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "CL-SOM-AM57x-Sound-Card"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Microphone", "Microphone Jack", + "Line", "Line Jack"; + simple-audio-card,routing = + "Headphone Jack", "RHPOUT", + "Headphone Jack", "LHPOUT", + "LLINEIN", "Line Jack", + "MICIN", "Mic Bias", + "Mic Bias", "Microphone Jack"; + + dailink0_master: simple-audio-card,cpu { + sound-dai = <&mcasp3>; + }; + + simple-audio-card,codec { + sound-dai = <&wm8731>; + system-clock-frequency = <12000000>; + }; + }; }; &dra7_pmx_core { @@ -196,6 +223,24 @@ DRA7XX_CORE_IOPAD(0x3464, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpmc_a9.gpio1_31 */ >; }; + + mcasp3_pins_default: mcasp3_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */ + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */ + DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */ + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */ + >; + }; + + mcasp3_pins_sleep: mcasp3_pins_sleep { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15) + >; + }; }; &i2c1 { @@ -392,6 +437,13 @@ reg = <0x50>; pagesize = <16>; }; + + wm8731: wm8731@1a { + #sound-dai-cells = <0>; + compatible = "wlf,wm8731"; + reg = <0x1a>; + status = "okay"; + }; }; &cpu0 { @@ -538,3 +590,18 @@ &usb2 { dr_mode = "peripheral"; }; + +&mcasp3 { + #sound-dai-cells = <0>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp3_pins_default>; + pinctrl-1 = <&mcasp3_pins_sleep>; + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 2 0 0 + >; +}; -- cgit v1.2.3 From e1fdd060f08df588a577b9fd969e85878da4d610 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:13 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add basic board support SBC-AM57x is a single board computer designed for industrial and embedded applications. It is based on the Texas Instruments Sitara AM57x system-on-chip family. SBC-AM57x is implemented with the CL-SOM-AM57x computer-on-module providing most of the functions, and SB-SOM-AM57x carrier board providing additional peripheral functions and connectors. https://www.compulab.co.il/products/sbcs/sbc-am57x-ti-am5728-am5718-single-board-computer/ https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/ Add basic board support, including UART3, used as a serial console. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/omap/omap.txt | 3 ++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am57xx-sbc-am57x.dts | 36 ++++++++++++++++++++++ 3 files changed, 40 insertions(+) create mode 100644 arch/arm/boot/dts/am57xx-sbc-am57x.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 1b9cae587707..0b2c946a0289 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -162,6 +162,9 @@ Boards: - AM57XX CL-SOM-AM57x compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM57XX SBC-AM57x + compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6e9a3af802ab..1cfb2990c40f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -493,6 +493,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-beagle-x15.dtb \ am57xx-cl-som-am57x.dtb \ + am57xx-sbc-am57x.dtb \ dra7-evm.dtb \ dra72-evm.dtb dtb-$(CONFIG_ARCH_ORION5X) += \ diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts new file mode 100644 index 000000000000..804ad727c963 --- /dev/null +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -0,0 +1,36 @@ +/* + * Support for CompuLab SBC-AM57x single board computer + * + * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * Author: Dmitry Lifshitz + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ + +#include "am57xx-cl-som-am57x.dts" +#include "compulab-sb-som.dtsi" + +/ { + model = "CompuLab CL-SOM-AM57x on SB-SOM-AM57x"; + compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"; +}; + +&dra7_pmx_core { + uart3_pins_default: uart3_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ + DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ + >; + }; +}; + +&uart3 { + status = "okay"; + interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <&dra7_pmx_core 0x3f8>; + + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_default>; +}; -- cgit v1.2.3 From 00d0e46a78f0f2f4a1de35d625d58ff4a84a48b5 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:14 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: add MMC1 support Add MMC1 support, used for SD/MMC card. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 804ad727c963..93852e278d1e 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -24,6 +24,19 @@ DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ >; }; + + mmc1_pins_default: mmc1_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1_sdcd.gpio6_27 */ + DRA7XX_CORE_IOPAD(0x377c, PIN_INPUT | MUX_MODE14) /* mmc1_sdwp.gpio6_28 */ + >; + }; }; &uart3 { @@ -34,3 +47,15 @@ pinctrl-names = "default"; pinctrl-0 = <&uart3_pins_default>; }; + +&mmc1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; + + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; +}; -- cgit v1.2.3 From ed7ce764ed8ec62fb4580aa74d412ce33c1d3b52 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:15 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux usb1_drvvbus pin is used to Drive-VBUS enable to external charge pump/power switch. Add a pinmux for that pin. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 93852e278d1e..17a1972ba821 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -37,6 +37,12 @@ DRA7XX_CORE_IOPAD(0x377c, PIN_INPUT | MUX_MODE14) /* mmc1_sdwp.gpio6_28 */ >; }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + >; + }; }; &uart3 { @@ -59,3 +65,8 @@ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; wp-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; }; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; +}; -- cgit v1.2.3 From 6042f620ad777b9186e97fa37c8bf7bc89b0f4c0 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:16 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add EEPROM support On-board EEPROM chip is used for storing a board production info. Add carrier board EEPROM support (over I2C5 bus). Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 17a1972ba821..a3588ba6f0b3 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -43,6 +43,13 @@ DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ >; }; + + i2c5_pins_default: i2c5_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT| MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT| MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + >; + }; }; &uart3 { @@ -70,3 +77,16 @@ pinctrl-names = "default"; pinctrl-0 = <&usb1_pins>; }; + +&i2c5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_default>; + clock-frequency = <400000>; + + eeprom_base: atmel@50 { + compatible = "atmel,24c08"; + reg = <0x50>; + pagesize = <16>; + }; +}; -- cgit v1.2.3 From 7442173e7932b7f79f645859409a8e4812088739 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:17 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add GPIO expander support Add PCA9555 GPIO expander support (over I2C5 bus). Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index a3588ba6f0b3..edce6c663279 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -89,4 +89,11 @@ reg = <0x50>; pagesize = <16>; }; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; }; -- cgit v1.2.3 From 85f99c759ba27989a335488bef15fd4477ece637 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:18 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add LCD support Startek-kd050c 800x480 LCD panel timings are described in compulab-sb-som.dtsi. Add appropriate DT endpoints to connect DPI output and LCD. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 38 ++++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index edce6c663279..8e4c0fdc2df6 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -15,6 +15,10 @@ / { model = "CompuLab CL-SOM-AM57x on SB-SOM-AM57x"; compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"; + + aliases { + display0 = &lcd0; + }; }; &dra7_pmx_core { @@ -50,6 +54,12 @@ DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT| MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ >; }; + + lcd_pins_default: lcd_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3564, PIN_OUTPUT | MUX_MODE14) /* vin2a_vsync0.gpio4_0 */ + >; + }; }; &uart3 { @@ -97,3 +107,31 @@ #gpio-cells = <2>; }; }; + +&dss { + status = "ok"; + + vdda_video-supply = <&ldoln_reg>; + + port { + dpi_lcd_out: endpoint@0 { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; + }; +}; + +&lcd0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins_default>; + + enable-gpios = <&pca9555 14 GPIO_ACTIVE_HIGH + &gpio4 0 GPIO_ACTIVE_HIGH>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_lcd_out>; + data-lines = <24>; + }; + }; +}; -- cgit v1.2.3 From 2e567d1c50d99aa63d2b7dd4dc25cff95a64d0db Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:19 +0200 Subject: ARM: dts: am57xx: compulab-sb-som: add HDMI connector Add HDMI connector node without a valid input endpoint. CompuLab SB-SOM is a carrier board, hence the endpoint should be added in the board DT with a valid HDMI output. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/compulab-sb-som.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/compulab-sb-som.dtsi b/arch/arm/boot/dts/compulab-sb-som.dtsi index 402a143c85c8..93d7e235bc80 100644 --- a/arch/arm/boot/dts/compulab-sb-som.dtsi +++ b/arch/arm/boot/dts/compulab-sb-som.dtsi @@ -39,4 +39,11 @@ pixelclk-active = <1>; }; }; + + hdmi_conn: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + }; }; -- cgit v1.2.3 From 2e0788d1948828fac45af86985cec6cba9824e8e Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:20 +0200 Subject: ARM: dts: am57xx: sbc-am57x: add HDMI support Add HDMI video output support. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 42 ++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 8e4c0fdc2df6..77bb8e17401a 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -18,6 +18,7 @@ aliases { display0 = &lcd0; + display1 = &hdmi; }; }; @@ -60,6 +61,19 @@ DRA7XX_CORE_IOPAD(0x3564, PIN_OUTPUT | MUX_MODE14) /* vin2a_vsync0.gpio4_0 */ >; }; + + hdmi_pins: pinmux_hdmi_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + >; + }; + + hdmi_conn_pins: pinmux_hdmi_conn_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT | MUX_MODE14) /* spi1_cs2.gpio7_12 */ + >; + }; }; &uart3 { @@ -135,3 +149,31 @@ }; }; }; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo4_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + lanes = <1 0 3 2 5 4 7 6>; + }; + }; +}; + +&hdmi_conn { + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_conn_pins>; + + hpd-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; +}; -- cgit v1.2.3 From ca17c4ff6d9e28f13db8a14ffe5ed9a8e3b9f774 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Tue, 1 Dec 2015 20:03:21 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs ETH PHYs setup on CL-SOM-AM57X is established in U-Boot along with bringing them out of reset. This is done by toggling GPIOs belonging to GPIO2/3 controllers on AM57xx. Skip resetting ETH PHYs, by adding "ti,no-reset-on-init" to GPIO2/3 controllers DT nodes. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index b2c44515f62d..c53882643ae9 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -605,3 +605,13 @@ 1 2 0 0 >; }; + +&gpio3 { + status = "okay"; + ti,no-reset-on-init; +}; + +&gpio2 { + status = "okay"; + ti,no-reset-on-init; +}; -- cgit v1.2.3 From 066111411101f6b020af1a7c752859a12476ba21 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Fri, 27 Nov 2015 23:35:00 +0100 Subject: ARM: dts: rockchip: add gpio-ir-receiver to the R89 board Add support for the IR receiver present on the R89 board. Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-r89.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-r89.dts b/arch/arm/boot/dts/rk3288-r89.dts index 14b9fc73c8a4..17f13c73fe5e 100644 --- a/arch/arm/boot/dts/rk3288-r89.dts +++ b/arch/arm/boot/dts/rk3288-r89.dts @@ -78,6 +78,13 @@ }; }; + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + vcc_host: vcc-host-regulator { compatible = "regulator-fixed"; enable-active-high; @@ -310,6 +317,12 @@ }; }; + ir { + ir_int: ir-int { + rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + pmic { pmic_int: pmic-int { rockchip,pins = ; -- cgit v1.2.3 From ac4111abf3521dfb3038c44c053f7c43ee1fb1bd Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 30 Nov 2015 21:54:39 +0800 Subject: arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we have gpios for card detection, write-protect, vqmmc and vmmc. This patch adds pinmux for this sdcard interface, then adds regulators for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties. Signed-off-by: Jisheng Zhang Signed-off-by: Sebastian Hesselbarth --- arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 37 ++++++++++++++++++++++++++++-- arch/arm/boot/dts/berlin2q.dtsi | 5 ++++ 2 files changed, 40 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts index cdcf89bfec33..33b28757b8f6 100644 --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts @@ -84,12 +84,45 @@ gpio = <&portb 12 GPIO_ACTIVE_HIGH>; enable-active-high; }; + + reg_sdio1_vmmc: regulator@3 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "sdio1_vmmc"; + enable-active-high; + regulator-boot-on; + gpio = <&portb 21 GPIO_ACTIVE_HIGH>; + }; + + reg_sdio1_vqmmc: regulator@4 { + compatible = "regulator-gpio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "sdio1_vqmmc"; + regulator-type = "voltage"; + enable-active-high; + gpios = <&portb 16 GPIO_ACTIVE_HIGH>; + states = <3300000 0x1 + 1800000 0x0>; + }; + }; +}; + +&soc_pinctrl { + sd1gpio_pmux: sd1pwr-pmux { + groups = "G23", "G32"; + function = "gpio"; }; }; &sdhci1 { - broken-cd; - sdhci,wp-inverted; + vmmc-supply = <®_sdio1_vmmc>; + vqmmc-supply = <®_sdio1_vqmmc>; + cd-gpios = <&portc 30 GPIO_ACTIVE_LOW>; + wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>; + pinctrl-names = "default"; status = "okay"; }; diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index 4241a615a74f..5f0abf6a89eb 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -415,6 +415,11 @@ soc_pinctrl: pin-controller { compatible = "marvell,berlin2q-soc-pinctrl"; + sd1_pmux: sd1-pmux { + groups = "G31"; + function = "sd1"; + }; + twsi0_pmux: twsi0-pmux { groups = "G6"; function = "twsi0"; -- cgit v1.2.3 From 5d3dc3938ee4649cbc47d1fd6f5716e798782ea5 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 29 Oct 2015 18:23:17 -0700 Subject: clk: iproc: Extend binding to cover BCM63138 Broadcom BCM63138 DSL SoCs have the same ARMPLL clocking infrastructure as the Cygnus and iProc chips, add a dedicated compatible string and document that the ARMPLL node is a valid node for this chip. Acked-by: Rob Herring Signed-off-by: Florian Fainelli Signed-off-by: Stephen Boyd --- Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index ede65a55e21b..0b35e71b39e8 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -208,3 +208,8 @@ These clock IDs are defined in: ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED + +BCM63138 +-------- +PLL and leaf clock compatible strings for BCM63138 are: + "brcm,bcm63138-armpll" -- cgit v1.2.3 From 7160aa1e5cdfb3fb8c0b6addb40c5f0e60cb0de0 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 29 Oct 2015 18:23:18 -0700 Subject: clk: bcm: Add BCM63138 clock support BCM63138 has a simple clocking domain which is primarily the ARMPLL clocking complex, from which the ARM (CPU), APB and AXI clocks would be derived from. Since the ARMPLL controller is entirely compatible with the iProc ARM PLL, we just initialize it without additional parameters. Signed-off-by: Florian Fainelli Signed-off-by: Stephen Boyd --- drivers/clk/bcm/Kconfig | 10 ++++++++++ drivers/clk/bcm/Makefile | 1 + drivers/clk/bcm/clk-bcm63xx.c | 22 ++++++++++++++++++++++ 3 files changed, 33 insertions(+) create mode 100644 drivers/clk/bcm/clk-bcm63xx.c diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig index 85260fb96b36..f2878459199a 100644 --- a/drivers/clk/bcm/Kconfig +++ b/drivers/clk/bcm/Kconfig @@ -1,3 +1,13 @@ +config CLK_BCM_63XX + bool "Broadcom BCM63xx clock support" + depends on ARCH_BCM_63XX || COMPILE_TEST + depends on COMMON_CLK + select COMMON_CLK_IPROC + default ARCH_BCM_63XX + help + Enable common clock framework support for Broadcom BCM63xx DSL SoCs + based on the ARM architecture + config CLK_BCM_KONA bool "Broadcom Kona CCU clock support" depends on ARCH_BCM_MOBILE || COMPILE_TEST diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile index 3fc95060d875..247c26750d8b 100644 --- a/drivers/clk/bcm/Makefile +++ b/drivers/clk/bcm/Makefile @@ -1,3 +1,4 @@ +obj-$(CONFIG_CLK_BCM_63XX) += clk-bcm63xx.o obj-$(CONFIG_CLK_BCM_KONA) += clk-kona.o obj-$(CONFIG_CLK_BCM_KONA) += clk-kona-setup.o obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm281xx.o diff --git a/drivers/clk/bcm/clk-bcm63xx.c b/drivers/clk/bcm/clk-bcm63xx.c new file mode 100644 index 000000000000..fbc17ae5ff2b --- /dev/null +++ b/drivers/clk/bcm/clk-bcm63xx.c @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2015 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include +#include +#include +#include "clk-iproc.h" + +static void __init bcm63138_armpll_init(struct device_node *node) +{ + iproc_armpll_setup(node); +} +CLK_OF_DECLARE(bcm63138_armpll, "brcm,bcm63138-armpll", bcm63138_armpll_init); -- cgit v1.2.3 From 511d30443a1c3e8a358c044b14587cbf3ed27a46 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 29 Oct 2015 18:23:19 -0700 Subject: ARM: dts: BCM63xx: Add ARMPLL device tree nodes Add the ARM PLL controller which comes standard with the Cortex-A9 found on the BCM63138 SoCs. This is the same controller as the one found in the Broadcom iProc architecture, however, we have a separate compatible string to indicate the integration difference, since the hardware is different. Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm63138.dtsi | 36 ++++++++++++++++++++++++++++-------- 1 file changed, 28 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/bcm63138.dtsi b/arch/arm/boot/dts/bcm63138.dtsi index 34cd64051250..d0560e8cd6de 100644 --- a/arch/arm/boot/dts/bcm63138.dtsi +++ b/arch/arm/boot/dts/bcm63138.dtsi @@ -43,18 +43,31 @@ #address-cells = <1>; #size-cells = <0>; - arm_timer_clk: arm_timer_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <500000000>; - }; - + /* UBUS peripheral clock */ periph_clk: periph_clk { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <50000000>; clock-output-names = "periph"; }; + + /* peripheral clock for system timer */ + axi_clk: axi_clk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&armpll>; + clock-div = <2>; + clock-mult = <1>; + }; + + /* APB bus clock */ + apb_clk: apb_clk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&armpll>; + clock-div = <4>; + clock-mult = <1>; + }; }; /* ARM bus */ @@ -93,14 +106,14 @@ compatible = "arm,cortex-a9-global-timer"; reg = <0x1e200 0x20>; interrupts = ; - clocks = <&arm_timer_clk>; + clocks = <&axi_clk>; }; local_timer: local-timer@1e600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x1e600 0x20>; interrupts = ; - clocks = <&arm_timer_clk>; + clocks = <&axi_clk>; }; twd_watchdog: watchdog@1e620 { @@ -109,6 +122,13 @@ interrupts = ; }; + armpll: armpll { + #clock-cells = <0>; + compatible = "brcm,bcm63138-armpll"; + clocks = <&periph_clk>; + reg = <0x20000 0xf00>; + }; + pmb0: reset-controller@4800c0 { compatible = "brcm,bcm63138-pmb"; reg = <0x4800c0 0x10>; -- cgit v1.2.3 From da41efd6041c694d93febdabee94552a2140dfbd Mon Sep 17 00:00:00 2001 From: RafaÅ‚ MiÅ‚ecki Date: Fri, 30 Oct 2015 15:44:01 +0100 Subject: ARM: BCM5301X: Add missing Netgear R8000 LEDs MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add a bunch of LEDs missing for the Netgear R8000: wireless, wps, 5Ghz radio and USB LEDs. Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 30 +++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts index 446c586cd473..b52927c94e35 100644 --- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts @@ -50,6 +50,36 @@ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; linux,default-trigger = "default-off"; }; + + wireless { + label = "bcm53xx:white:wireless"; + gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + + wps { + label = "bcm53xx:white:wps"; + gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + + 5ghz-2 { + label = "bcm53xx:white:5ghz-2"; + gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + usb3 { + label = "bcm53xx:white:usb3"; + gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + usb2 { + label = "bcm53xx:white:usb2"; + gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; }; gpio-keys { -- cgit v1.2.3 From 3ad8ff0e4ab3f908f93bd76afdad815060bb32db Mon Sep 17 00:00:00 2001 From: Pramod Kumar Date: Thu, 19 Nov 2015 09:22:14 +0530 Subject: ARM: dts: Cygnus: define ngpios property in gpio controller's node Add ngpios property in cygnus ASIU, CCM and CRMU gpio controller's node Signed-off-by: Pramod Kumar Reviewed-by: Ray Jui Reviewed-by: Scott Branden Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-cygnus.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index c9f1ac455e9a..f8b75a53181b 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -101,6 +101,7 @@ compatible = "brcm,cygnus-crmu-gpio"; reg = <0x03024800 0x50>, <0x03024008 0x18>; + ngpios = <6>; #gpio-cells = <2>; gpio-controller; }; @@ -127,6 +128,7 @@ compatible = "brcm,cygnus-ccm-gpio"; reg = <0x1800a000 0x50>, <0x0301d164 0x20>; + ngpios = <24>; #gpio-cells = <2>; gpio-controller; interrupts = ; @@ -245,6 +247,7 @@ gpio_asiu: gpio@180a5000 { compatible = "brcm,cygnus-asiu-gpio"; reg = <0x180a5000 0x668>; + ngpios = <146>; #gpio-cells = <2>; gpio-controller; -- cgit v1.2.3 From 44a06fa4654d07a5ed63e1e0d67cdee1e20818e7 Mon Sep 17 00:00:00 2001 From: Ray Jui Date: Wed, 18 Nov 2015 10:16:59 -0800 Subject: ARM: dts: enable PCIe PHY support for Cygnus Enable PCIe PHY for both PCIe root complexes on Cygnus Signed-off-by: Ray Jui Acked-by: Scott Branden [florian: Fix missing #address-cells and #size-cells properties] Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-cygnus.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index f8b75a53181b..815db5dd2f40 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -91,6 +91,23 @@ #address-cells = <1>; #size-cells = <1>; + pcie_phy: phy@0301d0a0 { + compatible = "brcm,cygnus-pcie-phy"; + reg = <0x0301d0a0 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + pcie0_phy: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + pcie1_phy: phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + pinctrl: pinctrl@0x0301d0c8 { compatible = "brcm,cygnus-pinmux"; reg = <0x0301d0c8 0x30>, @@ -163,6 +180,9 @@ ranges = <0x81000000 0 0 0x28000000 0 0x00010000 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + phys = <&pcie0_phy>; + phy-names = "pcie-phy"; + status = "disabled"; }; @@ -184,6 +204,9 @@ ranges = <0x81000000 0 0 0x48000000 0 0x00010000 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + phys = <&pcie1_phy>; + phy-names = "pcie-phy"; + status = "disabled"; }; -- cgit v1.2.3 From ea2d8975e3f6600868a5ffe5d1089139c44abcf4 Mon Sep 17 00:00:00 2001 From: Yendapally Reddy Dhananjaya Reddy Date: Fri, 20 Nov 2015 12:58:29 -0500 Subject: ARM: dts: enable pinctrl for Broadcom NSP This enables the pinctrl support for Broadcom NSP SoC Signed-off-by: Yendapally Reddy Dhananjaya Reddy Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 7 +++++++ arch/arm/boot/dts/bcm958625k.dts | 9 +++++++++ 2 files changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index d9bfc5618c25..4214818df3a0 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -277,5 +277,12 @@ "usbclk", "iprocfast", "sata1", "sata2"; }; + + pinctrl: pinctrl@3f1c0 { + compatible = "brcm,nsp-pinmux"; + reg = <0x3f1c0 0x04>, + <0x30028 0x04>, + <0x3f408 0x04>; + }; }; }; diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts index b966955260fa..e298450b49b2 100644 --- a/arch/arm/boot/dts/bcm958625k.dts +++ b/arch/arm/boot/dts/bcm958625k.dts @@ -105,3 +105,12 @@ }; }; }; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel>; + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; +}; -- cgit v1.2.3 From eaa870b3055384092d8fc075bca3a3a819f73c43 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Thu, 3 Dec 2015 01:21:49 +0300 Subject: ARM: shmobile: r8a7791: add EtherAVB clock Add the EtherAVB clock to the R8A7791 device tree. Based on the commit 63d2d750c902 ("ARM: shmobile: r8a7790: add EtherAVB clocks"). Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 10 ++++++---- include/dt-bindings/clock/r8a7791-clock.h | 1 + 2 files changed, 7 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 12b2b0f95806..4b3132d9807f 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1329,16 +1329,18 @@ compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150990 0 4>, <0 0xe61509a0 0 4>; clocks = <&zx_clk>, <&hp_clk>, <&zg_clk>, <&zg_clk>, - <&zg_clk>, <&p_clk>, <&zs_clk>, <&zs_clk>; + <&zg_clk>, <&hp_clk>, <&p_clk>, <&zs_clk>, + <&zs_clk>; #clock-cells = <1>; clock-indices = < R8A7791_CLK_IPMMU_SGX R8A7791_CLK_MLB R8A7791_CLK_VIN2 R8A7791_CLK_VIN1 R8A7791_CLK_VIN0 - R8A7791_CLK_ETHER R8A7791_CLK_SATA1 R8A7791_CLK_SATA0 + R8A7791_CLK_ETHERAVB R8A7791_CLK_ETHER + R8A7791_CLK_SATA1 R8A7791_CLK_SATA0 >; clock-output-names = - "ipmmu_sgx", "mlb", "vin2", "vin1", "vin0", "ether", - "sata1", "sata0"; + "ipmmu_sgx", "mlb", "vin2", "vin1", "vin0", + "etheravb", "ether", "sata1", "sata0"; }; mstp9_clks: mstp9_clks@e6150994 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; diff --git a/include/dt-bindings/clock/r8a7791-clock.h b/include/dt-bindings/clock/r8a7791-clock.h index dd09b73c4aaf..ffa11379b3f0 100644 --- a/include/dt-bindings/clock/r8a7791-clock.h +++ b/include/dt-bindings/clock/r8a7791-clock.h @@ -102,6 +102,7 @@ #define R8A7791_CLK_VIN2 9 #define R8A7791_CLK_VIN1 10 #define R8A7791_CLK_VIN0 11 +#define R8A7791_CLK_ETHERAVB 12 #define R8A7791_CLK_ETHER 13 #define R8A7791_CLK_SATA1 14 #define R8A7791_CLK_SATA0 15 -- cgit v1.2.3 From 46ece349aa54f6e55b5f8d30bbecbaf2884ba869 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Thu, 3 Dec 2015 01:23:03 +0300 Subject: ARM: shmobile: r8a7791: add EtherAVB DT support Define the generic R8A7791 part of the EtherAVB device node. Based on the commit f25d6b977240 ("ARM: shmobile: r8a7790: add EtherAVB DT support"). Signed-off-by: Sergei Shtylyov Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 4b3132d9807f..36559cb0eb6b 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -785,6 +785,18 @@ status = "disabled"; }; + avb: ethernet@e6800000 { + compatible = "renesas,etheravb-r8a7791", + "renesas,etheravb-rcar-gen2"; + reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>; + interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7791_CLK_ETHERAVB>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sata0: sata@ee300000 { compatible = "renesas,sata-r8a7791"; reg = <0 0xee300000 0 0x2000>; -- cgit v1.2.3 From f00be687f5fd2b626aa975dc4513cad525823c05 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 26 Nov 2015 13:26:20 +0900 Subject: ARM: shmobile: r8a7793: remove deprecated #gpio-range-cells Commit a1bc260bb5f5d9 ("gpio: clean up gpio-ranges documentation") declares the above property deprecated. That was more than 2 years ago. Remove it, so it doesn't get copied around needlessly. Based on similar work for the r8a7791 and r8a7794 by Wolfram Sang. Cc: Wolfram Sang Signed-off-by: Simon Horman Reported-by: Wolfram Sang Acked-by: Wolfram Sang --- arch/arm/boot/dts/r8a7793.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index cbcda80f4658..4c74a9229e71 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -233,7 +233,6 @@ pfc: pfc@e6060000 { compatible = "renesas,pfc-r8a7793"; reg = <0 0xe6060000 0 0x250>; - #gpio-range-cells = <3>; }; dmac0: dma-controller@e6700000 { -- cgit v1.2.3 From 82f8582feef4c048ee7ef0155a71c23614a7856d Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sat, 5 Dec 2015 21:16:44 +0800 Subject: ARM: dts: sun4i: Add DRAM gates The DRAM gates controls direct memory access for some peripherals. These peripherals include the display pipeline, so add the required gates to the simplefb nodes as well. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10.dtsi | 36 ++++++++++++++++++++++++++++++++---- 1 file changed, 32 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index aa90f319309b..849d0242ece8 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -66,7 +66,7 @@ "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0-hdmi"; clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, - <&ahb_gates 44>; + <&ahb_gates 44>, <&dram_gates 26>; status = "disabled"; }; @@ -75,7 +75,8 @@ "simple-framebuffer"; allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi"; clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, - <&ahb_gates 44>, <&ahb_gates 46>; + <&ahb_gates 44>, <&ahb_gates 46>, + <&dram_gates 25>, <&dram_gates 26>; status = "disabled"; }; @@ -84,7 +85,8 @@ "simple-framebuffer"; allwinner,pipeline = "de_fe0-de_be0-lcd0"; clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>, - <&ahb_gates 46>; + <&ahb_gates 46>, <&dram_gates 25>, + <&dram_gates 26>; status = "disabled"; }; @@ -93,7 +95,8 @@ "simple-framebuffer"; allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0"; clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>, - <&ahb_gates 44>, <&ahb_gates 46>; + <&ahb_gates 44>, <&ahb_gates 46>, + <&dram_gates 25>, <&dram_gates 26>; status = "disabled"; }; }; @@ -492,6 +495,31 @@ clock-output-names = "spi3"; }; + dram_gates: clk@01c20100 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-dram-gates-clk"; + reg = <0x01c20100 0x4>; + clocks = <&pll5 0>; + clock-indices = <0>, + <1>, <2>, + <3>, + <4>, + <5>, <6>, + <15>, + <24>, <25>, + <26>, <27>, + <28>, <29>; + clock-output-names = "dram_ve", + "dram_csi0", "dram_csi1", + "dram_ts", + "dram_tvd", + "dram_tve0", "dram_tve1", + "dram_output", + "dram_de_fe1", "dram_de_fe0", + "dram_de_be0", "dram_de_be1", + "dram_de_mp", "dram_ace"; + }; + codec_clk: clk@01c20140 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-codec-clk"; -- cgit v1.2.3 From 0b4bf5a5200b9ac5ddf545665f171feb5594677d Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sat, 5 Dec 2015 21:16:46 +0800 Subject: ARM: dts: sun7i: Add DRAM gates The DRAM gates controls direct memory access for some peripherals. These peripherals include the display pipeline, so add the required gates to the simplefb nodes as well. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20.dtsi | 32 +++++++++++++++++++++++++++++--- 1 file changed, 29 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index e02eb720c4fc..21169c0a6627 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -68,7 +68,7 @@ "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0-hdmi"; clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, - <&ahb_gates 44>; + <&ahb_gates 44>, <&dram_gates 26>; status = "disabled"; }; @@ -76,7 +76,8 @@ compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0"; - clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>; + clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>, + <&dram_gates 26>; status = "disabled"; }; @@ -85,7 +86,7 @@ "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0-tve0"; clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>, - <&ahb_gates 44>; + <&ahb_gates 44>, <&dram_gates 26>; status = "disabled"; }; }; @@ -501,6 +502,31 @@ clock-output-names = "spi3"; }; + dram_gates: clk@01c20100 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-dram-gates-clk"; + reg = <0x01c20100 0x4>; + clocks = <&pll5 0>; + clock-indices = <0>, + <1>, <2>, + <3>, + <4>, + <5>, <6>, + <15>, + <24>, <25>, + <26>, <27>, + <28>, <29>; + clock-output-names = "dram_ve", + "dram_csi0", "dram_csi1", + "dram_ts", + "dram_tvd", + "dram_tve0", "dram_tve1", + "dram_output", + "dram_de_fe1", "dram_de_fe0", + "dram_de_be0", "dram_de_be1", + "dram_de_mp", "dram_ace"; + }; + codec_clk: clk@01c20140 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-codec-clk"; -- cgit v1.2.3 From 079ae0c121fd23287f4ad2be9e9f8a13f63cae73 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Fri, 4 Dec 2015 14:29:02 +0100 Subject: ARM: mvebu: remove duplicated regulator definition in Armada 388 GP The Armada 388 GP Device Tree file describes two times a regulator named 'reg_usb2_1_vbus', with the exact same description. This has been wrong since Armada 388 GP support was introduced. Fixes: 928413bd859c0 ("ARM: mvebu: Add Armada 388 General Purpose Development Board support") Signed-off-by: Thomas Petazzoni Cc: # v4.0+ Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-388-gp.dts | 10 ---------- 1 file changed, 10 deletions(-) diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts index a633be3defda..cd316021d6ce 100644 --- a/arch/arm/boot/dts/armada-388-gp.dts +++ b/arch/arm/boot/dts/armada-388-gp.dts @@ -303,16 +303,6 @@ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>; }; - reg_usb2_1_vbus: v5-vbus1 { - compatible = "regulator-fixed"; - regulator-name = "v5.0-vbus1"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - gpio = <&expander0 4 GPIO_ACTIVE_HIGH>; - }; - reg_sata0: pwr-sata0 { compatible = "regulator-fixed"; regulator-name = "pwr_en_sata0"; -- cgit v1.2.3 From c6664ca0a368130efd6c337c1e1c298cb6b128e8 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 6 Dec 2015 23:28:26 +0000 Subject: dt-bindings: add Marvell core PLL and clock divider PMU documentation Add documentation for the Marvell clock divider driver, which is used to source clocks for the AXI bus, video decoder, GPU and LCD blocks. Acked-by: Andrew Lunn Acked-by: Sebastian Hesselbarth Acked-by: Rob Herring Signed-off-by: Russell King Signed-off-by: Gregory CLEMENT --- .../bindings/clock/dove-divider-clock.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/dove-divider-clock.txt diff --git a/Documentation/devicetree/bindings/clock/dove-divider-clock.txt b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt new file mode 100644 index 000000000000..e3eb0f657c5e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt @@ -0,0 +1,28 @@ +PLL divider based Dove clocks + +Marvell Dove has a 2GHz PLL, which feeds into a set of dividers to provide +high speed clocks for a number of peripherals. These dividers are part of +the PMU, and thus this node should be a child of the PMU node. + +The following clocks are provided: + +ID Clock +------------- +0 AXI bus clock +1 GPU clock +2 VMeta clock +3 LCD clock + +Required properties: +- compatible : shall be "marvell,dove-divider-clock" +- reg : shall be the register address of the Core PLL and Clock Divider + Control 0 register. This will cover that register, as well as the + Core PLL and Clock Divider Control 1 register. Thus, it will have + a size of 8. +- #clock-cells : from common clock binding; shall be set to 1 + +divider_clk: core-clock@0064 { + compatible = "marvell,dove-divider-clock"; + reg = <0x0064 0x8>; + #clock-cells = <1>; +}; -- cgit v1.2.3 From 860a8865659c035d26749093fb5e8f3c9a24fbeb Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 6 Dec 2015 23:28:37 +0000 Subject: ARM: dts: dove: add Dove divider clocks Add the Dove divider clocks to the Dove dtsi file. Acked-by: Andrew Lunn Signed-off-by: Russell King Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/dove.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index cd58c2e62757..9e109aab92d0 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -460,6 +460,12 @@ #clock-cells = <1>; }; + divider_clk: core-clock@0064 { + compatible = "marvell,dove-divider-clock"; + reg = <0x0064 0x8>; + #clock-cells = <1>; + }; + pinctrl: pin-ctrl@0200 { compatible = "marvell,dove-pinctrl"; reg = <0x0200 0x14>, -- cgit v1.2.3 From 9cfc5c90ad38c8fc11bfd39de42a107da00871ba Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 6 Dec 2015 23:52:21 +0000 Subject: dt-bindings: add Marvell PMU documentation Add the required DT binding documentation for the Marvell PMU driver. Acked-by: Rob Herring Acked-by: Arnd Bergmann Signed-off-by: Russell King Signed-off-by: Gregory CLEMENT --- Documentation/devicetree/bindings/soc/dove/pmu.txt | 56 ++++++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/dove/pmu.txt diff --git a/Documentation/devicetree/bindings/soc/dove/pmu.txt b/Documentation/devicetree/bindings/soc/dove/pmu.txt new file mode 100644 index 000000000000..edd40b796b74 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/dove/pmu.txt @@ -0,0 +1,56 @@ +Device Tree bindings for Marvell PMU + +Required properties: + - compatible: value should be "marvell,dove-pmu". + May also include "simple-bus" if there are child devices, in which + case the ranges node is required. + - reg: two base addresses and sizes of the PM controller and PMU. + - interrupts: single interrupt number for the PMU interrupt + - interrupt-controller: must be specified as the PMU itself is an + interrupt controller. + - #interrupt-cells: must be 1. + - #reset-cells: must be 1. + - domains: sub-node containing domain descriptions + +Optional properties: + - ranges: defines the address mapping for child devices, as per the + standard property of this name. Required when compatible includes + "simple-bus". + +Power domain descriptions are listed as child nodes of the "domains" +sub-node. Each domain has the following properties: + +Required properties: + - #power-domain-cells: must be 0. + +Optional properties: + - marvell,pmu_pwr_mask: specifies the mask value for PMU power register + - marvell,pmu_iso_mask: specifies the mask value for PMU isolation register + - resets: points to the reset manager (PMU node) and reset index. + +Example: + + pmu: power-management@d0000 { + compatible = "marvell,dove-pmu"; + reg = <0xd0000 0x8000>, <0xd8000 0x8000>; + interrupts = <33>; + interrupt-controller; + #interrupt-cells = <1>; + #reset-cells = <1>; + + domains { + vpu_domain: vpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000008>; + marvell,pmu_iso_mask = <0x00000001>; + resets = <&pmu 16>; + }; + + gpu_domain: gpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000004>; + marvell,pmu_iso_mask = <0x00000002>; + resets = <&pmu 18>; + }; + }; + }; -- cgit v1.2.3 From 7418111f88dfb92b33d9f765acba5fb45aefabeb Mon Sep 17 00:00:00 2001 From: Kapil Hali Date: Sat, 5 Dec 2015 06:53:40 -0500 Subject: dt-bindings: add SMP enable-method for Broadcom NSP Add a compatible string "brcm,bcm-nsp-smp" for Broadcom's Northstar Plus CPU to the 32-bit ARM CPU device tree binding documentation file and create a new binding documentation for Northstar Plus CPU. Signed-off-by: Kapil Hali Acked-by: Rob Herring Signed-off-by: Florian Fainelli --- .../bindings/arm/bcm/brcm,nsp-cpu-method.txt | 39 ++++++++++++++++++++++ Documentation/devicetree/bindings/arm/cpus.txt | 1 + 2 files changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt new file mode 100644 index 000000000000..677ef9d9f445 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt @@ -0,0 +1,39 @@ +Broadcom Northstar Plus SoC CPU Enable Method +--------------------------------------------- +This binding defines the enable method used for starting secondary +CPU in the following Broadcom SoCs: + BCM58522, BCM58525, BCM58535, BCM58622, BCM58623, BCM58625, BCM88312 + +The enable method is specified by defining the following required +properties in the corresponding secondary "cpu" device tree node: + - enable-method = "brcm,bcm-nsp-smp"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register which should hold the common +entry point for a secondary CPU. This entry is cpu node specific +and should be added per cpu. E.g., in case of NSP (BCM58625) which +is a dual core CPU SoC, this entry should be added to cpu1 node. + + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + enable-method = "brcm,bcm-nsp-smp"; + secondary-boot-reg = <0xffff042c>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 3a07a87fef20..d1915549e009 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -190,6 +190,7 @@ nodes to be present and contain the properties described below. "allwinner,sun6i-a31" "allwinner,sun8i-a23" "arm,psci" + "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" -- cgit v1.2.3 From 944725fcfff19d76205ac04d28e6e550ac2b3053 Mon Sep 17 00:00:00 2001 From: Kapil Hali Date: Sat, 5 Dec 2015 06:53:42 -0500 Subject: ARM: dts: Add SMP support for Broadcom NSP Add device tree changes required for providing SMP support for Broadcom Northstar Plus SoC. Signed-off-by: Kapil Hali Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-nsp.dtsi | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi index 4214818df3a0..10bdef557ba0 100644 --- a/arch/arm/boot/dts/bcm-nsp.dtsi +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -41,6 +41,27 @@ model = "Broadcom Northstar Plus SoC"; interrupt-parent = <&gic>; + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0x0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + enable-method = "brcm,bcm-nsp-smp"; + secondary-boot-reg = <0xffff042c>; + reg = <0x1>; + }; + }; + mpcore { compatible = "simple-bus"; ranges = <0x00000000 0x19000000 0x00023000>; -- cgit v1.2.3 From f6b889358a82c1f1a34bfcecfe8ebf709deb28ec Mon Sep 17 00:00:00 2001 From: Ray Jui Date: Fri, 4 Dec 2015 09:35:02 -0800 Subject: ARM: dts: Enable MSI support for Broadcom Cygnus Enable MSI support for Broadcom Cygnus platforms Signed-off-by: Ray Jui Reviewed-by: Anup Patel Reviewed-by: Pramod KUMAR Reviewed-by: Vikram Prakash Reviewed-by: Scott Branden Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm-cygnus.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index 815db5dd2f40..3878793364f0 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -184,6 +184,17 @@ phy-names = "pcie-phy"; status = "disabled"; + + msi-parent = <&msi0>; + msi0: msi@18012000 { + compatible = "brcm,iproc-msi"; + msi-controller; + interrupt-parent = <&gic>; + interrupts = , + , + , + ; + }; }; pcie1: pcie@18013000 { @@ -208,6 +219,17 @@ phy-names = "pcie-phy"; status = "disabled"; + + msi-parent = <&msi1>; + msi1: msi@18013000 { + compatible = "brcm,iproc-msi"; + msi-controller; + interrupt-parent = <&gic>; + interrupts = , + , + , + ; + }; }; uart0: serial@18020000 { -- cgit v1.2.3 From fd7e118c80d43496c49a4260712cd1c499a0f1b3 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 3 Dec 2015 15:02:08 -0300 Subject: ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi When the WiFi support was added to the IGEP0020 board, the MMC subsystem did not provide a mechanism to define power sequence providers. So a DT hack was used to toggle the WiFi chip reset and power down pins by using fake fixed regulators whose enable GPIO was the GPIOs connected to these pins. But now the simple MMC power sequence provider can be used for this and the workaround removed. Signed-off-by: Javier Martinez Canillas Acked-by: Enric Balletbo Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0020.dts | 24 ++++++++---------------- 1 file changed, 8 insertions(+), 16 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 3835e1569c29..33d6b4ead092 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -15,25 +15,17 @@ model = "IGEPv2 Rev. C (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0020", "ti,omap36xx", "ti,omap3"; - /* Regulator to trigger the WIFI_PDN signal of the Wifi module */ - lbee1usjyc_pdn: lbee1usjyc_pdn { + vmmcsdio_fixed: fixedregulator-mmcsdio { compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-pdn"; + regulator-name = "vmmcsdio_fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 - WIFI_PDN */ - startup-delay-us = <10000>; - enable-active-high; }; - /* Regulator to trigger the RESET_N_W signal of the Wifi module */ - lbee1usjyc_reset_n_w: lbee1usjyc_reset_n_w { - compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-reset-n-w"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - RESET_N_W */ - enable-active-high; + mmc2_pwrseq: mmc2_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>, /* gpio_139 - RESET_N_W */ + <&gpio5 10 GPIO_ACTIVE_LOW>; /* gpio_138 - WIFI_PDN */ }; }; @@ -51,8 +43,8 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins &lbee1usjyc_pins>; - vmmc-supply = <&lbee1usjyc_pdn>; - vmmc_aux-supply = <&lbee1usjyc_reset_n_w>; + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc2_pwrseq>; bus-width = <4>; non-removable; }; -- cgit v1.2.3 From 89c6f2e5ab7a0499c6bcb25d281977ada205765d Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 3 Dec 2015 15:02:09 -0300 Subject: ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi When the WiFi support was added to the IGEP0030 board, the MMC subsystem did not provide a mechanism to define power sequence providers. So a DT hack was used to toggle the WiFi chip reset and power down pins by using fake fixed regulators whose enable GPIO was the GPIOs connected to these pins. But now the simple MMC power sequence provider can be used for this and the workaround removed. Signed-off-by: Javier Martinez Canillas Acked-by: Enric Balletbo Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0030.dts | 24 ++++++++---------------- 1 file changed, 8 insertions(+), 16 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 468608dab30a..55b0cc4f5ee5 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -15,25 +15,17 @@ model = "IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0030", "ti,omap36xx", "ti,omap3"; - /* Regulator to trigger the WIFI_PDN signal of the Wifi module */ - lbee1usjyc_pdn: lbee1usjyc_pdn { + vmmcsdio_fixed: fixedregulator-mmcsdio { compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-pdn"; + regulator-name = "vmmcsdio_fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 - WIFI_PDN */ - startup-delay-us = <10000>; - enable-active-high; }; - /* Regulator to trigger the RESET_N_W signal of the Wifi module */ - lbee1usjyc_reset_n_w: lbee1usjyc_reset_n_w { - compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-reset-n-w"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - RESET_N_W */ - enable-active-high; + mmc2_pwrseq: mmc2_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>, /* gpio_139 - RESET_N_W */ + <&gpio5 10 GPIO_ACTIVE_LOW>; /* gpio_138 - WIFI_PDN */ }; }; @@ -62,8 +54,8 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins &lbee1usjyc_pins>; - vmmc-supply = <&lbee1usjyc_pdn>; - vmmc_aux-supply = <&lbee1usjyc_reset_n_w>; + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc2_pwrseq>; bus-width = <4>; non-removable; }; -- cgit v1.2.3 From a6ff5e8d5ebc0392d5c470652cd22f730e090e29 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 7 Dec 2015 17:25:37 +0100 Subject: ARM: shmobile: bockw dts: Override #sound-dai-cells to zero The default value of #sound-dai-cells in r8a7778.dtsi is one, while the /sound/simple-audio-card,cpu device node in r8a7778-bockw.dts uses a phandle without any extra cells ("<&rcar_sound>"), causing: /sound/simple-audio-card,cpu: arguments longer than property asoc-simple-card sound: parse error -22 asoc-simple-card: probe of sound failed with error -22 Override #sound-dai-cells to zero to fix this. Signed-off-by: Geert Uytterhoeven Acked-by: Kuninori Morimoto Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778-bockw.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index 3c03e6b8261e..158ad94fd4d1 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -172,6 +172,11 @@ }; }; +&rcar_sound { + /* Single DAI */ + #sound-dai-cells = <0>; +}; + &sdhi0 { pinctrl-0 = <&sdhi0_pins>, <&sdhi0_pup_pins>; pinctrl-names = "default"; -- cgit v1.2.3 From 2020dddd67c1884ea7cb9891b36aac7ff5e73038 Mon Sep 17 00:00:00 2001 From: Kuninori Morimoto Date: Tue, 8 Dec 2015 00:10:59 +0000 Subject: ARM: shmobile: r8a7778: tidyup #sound-dai-cells settings Renesas sound driver needs #sound-dai-cells settings, but, this usage is a little bit confusable. It came from ALSA SoC historical reasons. The sound DAI naming method is different between Single/Multi DAI in the ALSA framework, and it is used for sound card matching. And this #sound-dai-cells has relationship to it. Current SoC dtsi has #sound-dai-cells = <1> as default settings (= it is assuming that board/platform has multi DAI), and board/platform side needs to overwrite it if board/platform was single DAI. This style is more confusable for users. This patch removes SoC side default settings, and force to set it by board/platform side. Signed-off-by: Kuninori Morimoto Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778.dtsi | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index 4f8e07811746..b140627dd88b 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -236,7 +236,12 @@ }; rcar_sound: sound@ffd90000 { - #sound-dai-cells = <1>; + /* + * #sound-dai-cells is required + * + * Single DAI : #sound-dai-cells = <0>; <&rcar_sound>; + * Multi DAI : #sound-dai-cells = <1>; <&rcar_sound N>; + */ compatible = "renesas,rcar_sound-r8a7778", "renesas,rcar_sound-gen1"; reg = <0xffd90000 0x1000>, /* SRU */ <0xffd91000 0x240>, /* SSI */ -- cgit v1.2.3 From 318d93bc41823e86967c8251eef0444a72e4d687 Mon Sep 17 00:00:00 2001 From: Jens Kuske Date: Fri, 4 Dec 2015 22:24:42 +0100 Subject: ARM: dts: sunxi: Add Allwinner H3 DTSI The Allwinner H3 is a home entertainment system oriented SoC with four Cortex-A7 cores and a Mali-400MP2 GPU. Signed-off-by: Jens Kuske Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 497 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi new file mode 100644 index 000000000000..1524130e43c9 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -0,0 +1,497 @@ +/* + * Copyright (C) 2015 Jens Kuske + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" + +#include +#include + +/ { + interrupt-parent = <&gic>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <3>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = , + , + , + ; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc24M: osc24M_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "osc24M"; + }; + + osc32k: osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "osc32k"; + }; + + pll1: clk@01c20000 { + #clock-cells = <0>; + compatible = "allwinner,sun8i-a23-pll1-clk"; + reg = <0x01c20000 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll1"; + }; + + /* dummy clock until actually implemented */ + pll5: pll5_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + clock-output-names = "pll5"; + }; + + pll6: clk@01c20028 { + #clock-cells = <1>; + compatible = "allwinner,sun6i-a31-pll6-clk"; + reg = <0x01c20028 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll6", "pll6x2"; + }; + + pll6d2: pll6d2_clk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <2>; + clock-mult = <1>; + clocks = <&pll6 0>; + clock-output-names = "pll6d2"; + }; + + /* dummy clock until pll6 can be reused */ + pll8: pll8_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <1>; + clock-output-names = "pll8"; + }; + + cpu: cpu_clk@01c20050 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-cpu-clk"; + reg = <0x01c20050 0x4>; + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>; + clock-output-names = "cpu"; + }; + + axi: axi_clk@01c20050 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-axi-clk"; + reg = <0x01c20050 0x4>; + clocks = <&cpu>; + clock-output-names = "axi"; + }; + + ahb1: ahb1_clk@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun6i-a31-ahb1-clk"; + reg = <0x01c20054 0x4>; + clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>; + clock-output-names = "ahb1"; + }; + + ahb2: ahb2_clk@01c2005c { + #clock-cells = <0>; + compatible = "allwinner,sun8i-h3-ahb2-clk"; + reg = <0x01c2005c 0x4>; + clocks = <&ahb1>, <&pll6d2>; + clock-output-names = "ahb2"; + }; + + apb1: apb1_clk@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-apb0-clk"; + reg = <0x01c20054 0x4>; + clocks = <&ahb1>; + clock-output-names = "apb1"; + }; + + apb2: apb2_clk@01c20058 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-apb1-clk"; + reg = <0x01c20058 0x4>; + clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>; + clock-output-names = "apb2"; + }; + + bus_gates: clk@01c20060 { + #clock-cells = <1>; + compatible = "allwinner,sun8i-h3-bus-gates-clk"; + reg = <0x01c20060 0x14>; + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>; + clock-names = "ahb1", "ahb2", "apb1", "apb2"; + clock-indices = <5>, <6>, <8>, + <9>, <10>, <13>, + <14>, <17>, <18>, + <19>, <20>, + <21>, <23>, + <24>, <25>, + <26>, <27>, + <28>, <29>, + <30>, <31>, <32>, + <35>, <36>, <37>, + <40>, <41>, <43>, + <44>, <52>, <53>, + <54>, <64>, + <65>, <69>, <72>, + <76>, <77>, <78>, + <96>, <97>, <98>, + <112>, <113>, + <114>, <115>, + <116>, <128>, <135>; + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0", + "bus_mmc1", "bus_mmc2", "bus_nand", + "bus_sdram", "bus_gmac", "bus_ts", + "bus_hstimer", "bus_spi0", + "bus_spi1", "bus_otg", + "bus_otg_ehci0", "bus_ehci1", + "bus_ehci2", "bus_ehci3", + "bus_otg_ohci0", "bus_ohci1", + "bus_ohci2", "bus_ohci3", "bus_ve", + "bus_lcd0", "bus_lcd1", "bus_deint", + "bus_csi", "bus_tve", "bus_hdmi", + "bus_de", "bus_gpu", "bus_msgbox", + "bus_spinlock", "bus_codec", + "bus_spdif", "bus_pio", "bus_ths", + "bus_i2s0", "bus_i2s1", "bus_i2s2", + "bus_i2c0", "bus_i2c1", "bus_i2c2", + "bus_uart0", "bus_uart1", + "bus_uart2", "bus_uart3", + "bus_scr", "bus_ephy", "bus_dbg"; + }; + + mmc0_clk: clk@01c20088 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-mmc-clk"; + reg = <0x01c20088 0x4>; + clocks = <&osc24M>, <&pll6 0>, <&pll8>; + clock-output-names = "mmc0", + "mmc0_output", + "mmc0_sample"; + }; + + mmc1_clk: clk@01c2008c { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-mmc-clk"; + reg = <0x01c2008c 0x4>; + clocks = <&osc24M>, <&pll6 0>, <&pll8>; + clock-output-names = "mmc1", + "mmc1_output", + "mmc1_sample"; + }; + + mmc2_clk: clk@01c20090 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-mmc-clk"; + reg = <0x01c20090 0x4>; + clocks = <&osc24M>, <&pll6 0>, <&pll8>; + clock-output-names = "mmc2", + "mmc2_output", + "mmc2_sample"; + }; + + mbus_clk: clk@01c2015c { + #clock-cells = <0>; + compatible = "allwinner,sun8i-a23-mbus-clk"; + reg = <0x01c2015c 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5>; + clock-output-names = "mbus"; + }; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dma: dma-controller@01c02000 { + compatible = "allwinner,sun8i-h3-dma"; + reg = <0x01c02000 0x1000>; + interrupts = ; + clocks = <&bus_gates 6>; + resets = <&ahb_rst 6>; + #dma-cells = <1>; + }; + + mmc0: mmc@01c0f000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&bus_gates 8>, + <&mmc0_clk 0>, + <&mmc0_clk 1>, + <&mmc0_clk 2>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ahb_rst 8>; + reset-names = "ahb"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@01c10000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c10000 0x1000>; + clocks = <&bus_gates 9>, + <&mmc1_clk 0>, + <&mmc1_clk 1>, + <&mmc1_clk 2>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ahb_rst 9>; + reset-names = "ahb"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@01c11000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c11000 0x1000>; + clocks = <&bus_gates 10>, + <&mmc2_clk 0>, + <&mmc2_clk 1>, + <&mmc2_clk 2>; + clock-names = "ahb", + "mmc", + "output", + "sample"; + resets = <&ahb_rst 10>; + reset-names = "ahb"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + pio: pinctrl@01c20800 { + compatible = "allwinner,sun8i-h3-pinctrl"; + reg = <0x01c20800 0x400>; + interrupts = , + ; + clocks = <&bus_gates 69>; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <2>; + + uart0_pins_a: uart0@0 { + allwinner,pins = "PA4", "PA5"; + allwinner,function = "uart0"; + allwinner,drive = ; + allwinner,pull = ; + }; + + mmc0_pins_a: mmc0@0 { + allwinner,pins = "PF0", "PF1", "PF2", "PF3", + "PF4", "PF5"; + allwinner,function = "mmc0"; + allwinner,drive = ; + allwinner,pull = ; + }; + + mmc0_cd_pin: mmc0_cd_pin@0 { + allwinner,pins = "PF6"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + mmc1_pins_a: mmc1@0 { + allwinner,pins = "PG0", "PG1", "PG2", "PG3", + "PG4", "PG5"; + allwinner,function = "mmc1"; + allwinner,drive = ; + allwinner,pull = ; + }; + }; + + ahb_rst: reset@01c202c0 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-ahb1-reset"; + reg = <0x01c202c0 0xc>; + }; + + apb1_rst: reset@01c202d0 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-clock-reset"; + reg = <0x01c202d0 0x4>; + }; + + apb2_rst: reset@01c202d8 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-clock-reset"; + reg = <0x01c202d8 0x4>; + }; + + timer@01c20c00 { + compatible = "allwinner,sun4i-a10-timer"; + reg = <0x01c20c00 0xa0>; + interrupts = , + ; + clocks = <&osc24M>; + }; + + wdt0: watchdog@01c20ca0 { + compatible = "allwinner,sun6i-a31-wdt"; + reg = <0x01c20ca0 0x20>; + interrupts = ; + }; + + uart0: serial@01c28000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28000 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&bus_gates 112>; + resets = <&apb2_rst 16>; + dmas = <&dma 6>, <&dma 6>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart1: serial@01c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&bus_gates 113>; + resets = <&apb2_rst 17>; + dmas = <&dma 7>, <&dma 7>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart2: serial@01c28800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28800 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&bus_gates 114>; + resets = <&apb2_rst 18>; + dmas = <&dma 8>, <&dma 8>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart3: serial@01c28c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28c00 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&bus_gates 115>; + resets = <&apb2_rst 19>; + dmas = <&dma 9>, <&dma 9>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + gic: interrupt-controller@01c81000 { + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; + reg = <0x01c81000 0x1000>, + <0x01c82000 0x1000>, + <0x01c84000 0x2000>, + <0x01c86000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = ; + }; + + rtc: rtc@01f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x54>; + interrupts = , + ; + }; + }; +}; -- cgit v1.2.3 From dfcf8196de7411a5e7fd49795938b1bc8c56859c Mon Sep 17 00:00:00 2001 From: Jens Kuske Date: Fri, 4 Dec 2015 22:24:43 +0100 Subject: ARM: dts: sun8i: Add Orange Pi Plus support The Orange Pi Plus is a SBC based on the Allwinner H3 SoC with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port, WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector and a 40-pin GPIO header. Signed-off-by: Jens Kuske Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 ++++++++++++++++++++++++++++ 2 files changed, 79 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e8f44c705089..cc7309be499f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -661,7 +661,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a33-ga10h-v1.1.dtb \ sun8i-a33-ippo-q8h-v1.2.dtb \ sun8i-a33-q8-tablet.dtb \ - sun8i-a33-sinlinx-sina33.dtb + sun8i-a33-sinlinx-sina33.dtb \ + sun8i-h3-orangepi-plus.dtb dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ sun9i-a80-cubieboard4.dtb diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts new file mode 100644 index 000000000000..e67df590535f --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts @@ -0,0 +1,77 @@ +/* + * Copyright (C) 2015 Jens Kuske + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include + +/ { + model = "Xunlong Orange Pi Plus"; + compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-inverted; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; -- cgit v1.2.3 From 1ccc4939220cf815c309feddcf82dba260499194 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sat, 5 Dec 2015 21:16:45 +0800 Subject: ARM: dts: sun4i: Add VE (Video Engine) module clock node The video engine has its own module clock, which also includes a reset control for it. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index 849d0242ece8..2c8f5e6ad905 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -520,6 +520,15 @@ "dram_de_mp", "dram_ace"; }; + ve_clk: clk@01c2013c { + #clock-cells = <0>; + #reset-cells = <0>; + compatible = "allwinner,sun4i-a10-ve-clk"; + reg = <0x01c2013c 0x4>; + clocks = <&pll4>; + clock-output-names = "ve"; + }; + codec_clk: clk@01c20140 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-codec-clk"; -- cgit v1.2.3 From f0571ab140723f9a898d4a404118580534dcc468 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sat, 5 Dec 2015 21:16:47 +0800 Subject: ARM: dts: sun7i: Add VE (Video Engine) module clock node The video engine has its own module clock, which also includes a reset control for it. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 21169c0a6627..0940a788f824 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -527,6 +527,15 @@ "dram_de_mp", "dram_ace"; }; + ve_clk: clk@01c2013c { + #clock-cells = <0>; + #reset-cells = <0>; + compatible = "allwinner,sun4i-a10-ve-clk"; + reg = <0x01c2013c 0x4>; + clocks = <&pll4>; + clock-output-names = "ve"; + }; + codec_clk: clk@01c20140 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-codec-clk"; -- cgit v1.2.3 From 4c945e8556ec7ea5b19d4f8721b212f468656e0d Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 6 Dec 2015 21:52:06 +0000 Subject: ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT file Add support for the SolidRun Armada 388 Clearfog A1 board. This board has an Armada 388 microsom, dedicated gigabit ethernet, six switched gigabit ethernet ports, SFP cage, two Mini-PCIe/mSATA slots, a m.2 SATA slot, and a MikroBUS connector to allow MikroBUS modules to be added. This DT file adds support for all board facilities with the exception of full SFP support. Signed-off-by: Russell King Acked-by: Gregory CLEMENT Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-388-clearfog.dts | 456 +++++++++++++++++++++ .../arm/boot/dts/armada-38x-solidrun-microsom.dtsi | 115 ++++++ 3 files changed, 572 insertions(+) create mode 100644 arch/arm/boot/dts/armada-388-clearfog.dts create mode 100644 arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..7e6a0532c656 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -748,6 +748,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-385-db-ap.dtb \ armada-385-linksys-caiman.dtb \ armada-385-linksys-cobra.dtb \ + armada-388-clearfog.dtb \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb diff --git a/arch/arm/boot/dts/armada-388-clearfog.dts b/arch/arm/boot/dts/armada-388-clearfog.dts new file mode 100644 index 000000000000..c6e180eb3b11 --- /dev/null +++ b/arch/arm/boot/dts/armada-388-clearfog.dts @@ -0,0 +1,456 @@ +/* + * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * + * Copyright (C) 2015 Russell King + * + * This board is in development; the contents of this file work with + * the A1 rev 2.0 of the board, which does not represent final + * production board. Things will change, don't expect this file to + * remain compatible info the future. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" + +/ { + model = "SolidRun Clearfog A1"; + compatible = "solidrun,clearfog-a1", "marvell,armada388", + "marvell,armada385", "marvell,armada380"; + + aliases { + /* So that mvebu u-boot can update the MAC addresses */ + ethernet1 = ð0; + ethernet2 = ð1; + ethernet3 = ð2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + soc { + internal-regs { + ethernet@30000 { + phy-mode = "sgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + ethernet@34000 { + phy-mode = "sgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + i2c@11000 { + /* Is there anything on this? */ + clock-frequency = <100000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-CON3 CLKREQ# + * 1-CON3 PERST# + * 2-CON2 PERST# + * 3-CON3 W_DISABLE + * 4-CON2 CLKREQ# + * 5-USB3 overcurrent + * 6-USB3 power + * 7-CON2 W_DISABLE + * 8-JP4 P1 + * 9-JP4 P4 + * 10-JP4 P5 + * 11-m.2 DEVSLP + * 12-SFP_LOS + * 13-SFP_TX_FAULT + * 14-SFP_TX_DISABLE + * 15-SFP_MOD_DEF0 + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + + pcie1_0_clkreq { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie1.0-clkreq"; + }; + pcie1_0_w_disable { + gpio-hog; + gpios = <3 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie1.0-w-disable"; + }; + pcie2_0_clkreq { + gpio-hog; + gpios = <4 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie2.0-clkreq"; + }; + pcie2_0_w_disable { + gpio-hog; + gpios = <7 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie2.0-w-disable"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + input; + line-name = "usb3-current-limit"; + }; + usb3_power { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb3-power"; + }; + m2_devslp { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "m.2 devslp"; + }; + sfp_los { + /* SFP loss of signal */ + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + input; + line-name = "sfp-los"; + }; + sfp_tx_fault { + /* SFP laser fault */ + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + input; + line-name = "sfp-tx-fault"; + }; + sfp_tx_disable { + /* SFP transmit disable */ + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "sfp-tx-disable"; + }; + sfp_mod_def0 { + /* SFP module present */ + gpio-hog; + gpios = <15 GPIO_ACTIVE_LOW>; + input; + line-name = "sfp-mod-def0"; + }; + }; + + /* The MCP3021 is 100kHz clock only */ + mikrobus_adc: mcp3021@4c { + compatible = "microchip,mcp3021"; + reg = <0x4c>; + }; + + /* Also something at 0x64 */ + }; + + i2c@11100 { + /* + * Routed to SFP, mikrobus, and PCIe. + * SFP limits this to 100kHz, and requires + * an AT24C01A/02/04 with address pins tied + * low, which takes addresses 0x50 and 0x51. + * Mikrobus doesn't specify beyond an I2C + * bus being present. + * PCIe uses ARP to assign addresses, or + * 0x63-0x64. + */ + clock-frequency = <100000>; + pinctrl-0 = <&clearfog_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + mdio@72004 { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + phy_dedicated: ethernet-phy@0 { + /* + * Annoyingly, the marvell phy driver + * configures the LED register, rather + * than preserving reset-loaded setting. + * We undo that rubbish here. + */ + marvell,reg-init = <3 16 0 0x101e>; + reg = <0>; + }; + }; + + pinctrl@18000 { + clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins { + marvell,pins = "mpp46"; + marvell,function = "ref"; + }; + clearfog_dsa0_pins: clearfog-dsa0-pins { + marvell,pins = "mpp23", "mpp41"; + marvell,function = "gpio"; + }; + clearfog_i2c1_pins: i2c1-pins { + /* SFP, PCIe, mSATA, mikrobus */ + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + clearfog_sdhci_pins: clearfog-sdhci-pins { + marvell,pins = "mpp21", "mpp28", + "mpp37", "mpp38", + "mpp39", "mpp40"; + marvell,function = "sd0"; + }; + clearfog_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp55"; + marvell,function = "spi1"; + }; + mikro_pins: mikro-pins { + /* int: mpp22 rst: mpp29 */ + marvell,pins = "mpp22", "mpp29"; + marvell,function = "gpio"; + }; + mikro_spi_pins: mikro-spi-pins { + marvell,pins = "mpp43"; + marvell,function = "spi1"; + }; + mikro_uart_pins: mikro-uart-pins { + marvell,pins = "mpp24", "mpp25"; + marvell,function = "ua1"; + }; + rear_button_pins: rear-button-pins { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + }; + + sata@a8000 { + /* pinctrl? */ + status = "okay"; + }; + + sata@e0000 { + /* pinctrl? */ + status = "okay"; + }; + + sdhci@d8000 { + bus-width = <4>; + cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + no-1-8-v; + pinctrl-0 = <&clearfog_sdhci_pins + &clearfog_sdhci_cd_pins>; + pinctrl-names = "default"; + status = "okay"; + vmmc = <®_3p3v>; + wp-inverted; + }; + + serial@12100 { + /* mikrobus uart */ + pinctrl-0 = <&mikro_uart_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + spi@10680 { + /* + * We don't seem to have the W25Q32 on the + * A1 Rev 2.0 boards, so disable SPI. + * CS0: W25Q32 (doesn't appear to be present) + * CS1: + * CS2: mikrobus + */ + pinctrl-0 = <&spi1_pins + &clearfog_spi1_cs_pins + &mikro_spi_pins>; + pinctrl-names = "default"; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "w25q32", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <3000000>; + status = "disabled"; + }; + }; + + usb@58000 { + /* CON3, nearest power. */ + status = "okay"; + }; + + usb3@f0000 { + /* CON2, nearest CPU, USB2 only. */ + status = "okay"; + }; + + usb3@f8000 { + /* CON7 */ + status = "okay"; + }; + }; + + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * the mini-PCIe connectors on the board. + */ + pcie@2,0 { + /* Port 1, Lane 0. CON3, nearest power. */ + reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + pcie@3,0 { + /* Port 2, Lane 0. CON2, nearest CPU. */ + reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + }; + }; + + dsa@0 { + compatible = "marvell,dsa"; + dsa,ethernet = <ð1>; + dsa,mii-bus = <&mdio>; + pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>; + pinctrl-names = "default"; + #address-cells = <2>; + #size-cells = <0>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4 0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "lan5"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + + port@6 { + /* 88E1512 external phy */ + reg = <6>; + label = "lan6"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&rear_button_pins>; + pinctrl-names = "default"; + + button_0 { + /* The rear SW3 button */ + label = "Rear Button"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + linux,can-disable; + linux,code = ; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi new file mode 100644 index 000000000000..3f792a563c05 --- /dev/null +++ b/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi @@ -0,0 +1,115 @@ +/* + * Device Tree file for SolidRun Armada 38x Microsom + * + * Copyright (C) 2015 Russell King + * + * This board is in development; the contents of this file work with + * the A1 rev 2.0 of the board, which does not represent final + * production board. Things will change, don't expect this file to + * remain compatible info the future. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include +#include + +/ { + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; /* 256 MB */ + }; + + soc { + ranges = ; + + internal-regs { + ethernet@70000 { + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy_dedicated>; + phy-mode = "rgmii-id"; + status = "okay"; + }; + + mdio@72004 { + /* + * Add the phy clock here, so the phy can be + * accessed to read its IDs prior to binding + * with the driver. + */ + pinctrl-0 = <&mdio_pins µsom_phy_clk_pins>; + pinctrl-names = "default"; + + phy_dedicated: ethernet-phy@0 { + /* + * Annoyingly, the marvell phy driver + * configures the LED register, rather + * than preserving reset-loaded setting. + * We undo that rubbish here. + */ + marvell,reg-init = <3 16 0 0x101e>; + reg = <0>; + }; + }; + + pinctrl@18000 { + microsom_phy_clk_pins: microsom-phy-clk-pins { + marvell,pins = "mpp45"; + marvell,function = "ref"; + }; + }; + + rtc@a3800 { + /* + * If the rtc doesn't work, run "date reset" + * twice in u-boot. + */ + status = "okay"; + }; + + serial@12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + }; + }; +}; -- cgit v1.2.3 From c2e1445c2a25ccc28054200ef3921decbfae4bf9 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:44 -0700 Subject: ARM: dts: qcom: msm8974-honami: Define pinctrl state for blsp_uart2 Make sure the blsp1_uart2 pins are in the correct state for the uart. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 23 ++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 016f9ad9392a..6f7e4ef4ccf7 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -23,6 +23,29 @@ &soc { serial@f991e000 { status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart2_pin_a>; + }; + + pinctrl@fd510000 { + blsp1_uart2_pin_a: blsp1-uart2-pin-active { + rx { + pins = "gpio5"; + function = "blsp_uart2"; + + drive-strength = <2>; + bias-pull-up; + }; + + tx { + pins = "gpio4"; + function = "blsp_uart2"; + + drive-strength = <4>; + bias-disable; + }; + }; }; }; -- cgit v1.2.3 From 0c808ab5ea1e13c45d1e87c0dc183bee7121457f Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:45 -0700 Subject: ARM: dts: qcom: msm8974-honami: Add regulator nodes for Honami Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 226 +++++++++++++++++++++ 1 file changed, 226 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 6f7e4ef4ccf7..5768c97bb124 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -1,6 +1,8 @@ #include "qcom-msm8974.dtsi" #include "qcom-pm8841.dtsi" #include "qcom-pm8941.dtsi" +#include +#include / { model = "Sony Xperia Z1"; @@ -18,6 +20,223 @@ reg = <0 0x40000000>, <0x40000000 0x40000000>; device_type = "memory"; }; + + smd { + rpm { + rpm_requests { + pm8841-regulators { + s1 { + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <1050000>; + }; + + s2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + }; + + pm8941-regulators { + vdd_l1_l3-supply = <&pm8941_s1>; + vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; + vdd_l4_l11-supply = <&pm8941_s1>; + vdd_l5_l7-supply = <&pm8941_s2>; + vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; + vdd_l9_l10_l17_l22-supply = <&vreg_boost>; + vdd_l13_l20_l23_l24-supply = <&vreg_boost>; + vdd_l21-supply = <&vreg_boost>; + vin_5vs-supply = <&pm8941_5v>; + + s1 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + s2 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + regulator-boot-on; + }; + + s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + s4 { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + + regulator-always-on; + regulator-boot-on; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l11 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1350000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + }; + + l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l15 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-allow-set-load; + regulator-boot-on; + regulator-system-load = <200000>; + }; + + l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + l23 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + + regulator-boot-on; + }; + }; + }; + }; + }; + + vreg_boost: vreg-boost { + compatible = "regulator-fixed"; + + regulator-name = "vreg-boost"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3150000>; + + regulator-always-on; + regulator-boot-on; + + gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&boost_bypass_n_pin>; + }; }; &soc { @@ -51,6 +270,13 @@ &spmi_bus { pm8941@0 { + gpios@c000 { + boost_bypass_n_pin: boost-bypass { + pins = "gpio21"; + function = "normal"; + }; + }; + coincell@2800 { status = "ok"; qcom,rset-ohms = <2100>; -- cgit v1.2.3 From e29d22e08eec3a2278e1aa84ea79892e69439cb6 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:46 -0700 Subject: ARM: dts: qcom: msm8974-honami: Introduce gpio-keys Introduce a gpio-keys node defining the physical keys of the Honami and the associated pinctrl state. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 45 ++++++++++++++++++++++ 1 file changed, 45 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 5768c97bb124..d30f407b04d3 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -2,6 +2,7 @@ #include "qcom-pm8841.dtsi" #include "qcom-pm8941.dtsi" #include +#include #include / { @@ -16,6 +17,42 @@ stdout-path = "serial0:115200n8"; }; + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_pin_a>; + + volume-down { + label = "volume_down"; + gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + camera-snapshot { + label = "camera_snapshot"; + gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + camera-focus { + label = "camera_focus"; + gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + volume-up { + label = "volume_up"; + gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + }; + memory@0 { reg = <0 0x40000000>, <0x40000000 0x40000000>; device_type = "memory"; @@ -275,6 +312,14 @@ pins = "gpio21"; function = "normal"; }; + + gpio_keys_pin_a: gpio-keys-active { + pins = "gpio2", "gpio3", "gpio4", "gpio5"; + function = "normal"; + + bias-pull-up; + power-source = ; + }; }; coincell@2800 { -- cgit v1.2.3 From f44cfceed9b444a959cfca09d8ea9736ad3627a1 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:47 -0700 Subject: ARM: dts: qcom: msm8974-honami: Add sdhci1 node Introduce the eMMC sdhci node and its pinctrl state. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 27 ++++++++++++++++++++++ 1 file changed, 27 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index d30f407b04d3..5f68eb270774 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -277,6 +277,19 @@ }; &soc { + sdhci@f9824900 { + status = "ok"; + + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; + + bus-width = <8>; + non-removable; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc1_pin_a>; + }; + serial@f991e000 { status = "ok"; @@ -302,6 +315,20 @@ bias-disable; }; }; + + sdhc1_pin_a: sdhc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-data { + pins = "sdc1_cmd", "sdc1_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; }; }; -- cgit v1.2.3 From b9526a81ba92d648cb542e6053a25293b113f991 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:48 -0700 Subject: ARM: dts: qcom: msm8974-honami: Add uSD slot nodes Add and enable the sdhci2 slot, the pinctrl configuration and card detect. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 37 ++++++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 5f68eb270774..e7e796888a21 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -290,6 +290,20 @@ pinctrl-0 = <&sdhc1_pin_a>; }; + sdhci@f98a4900 { + status = "ok"; + + bus-width = <4>; + + vmmc-supply = <&pm8941_l21>; + vqmmc-supply = <&pm8941_l13>; + + cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>; + }; + serial@f991e000 { status = "ok"; @@ -329,6 +343,29 @@ bias-pull-up; }; }; + + sdhc2_cd_pin_a: sdhc2-cd-pin-active { + pins = "gpio62"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + sdhc2_pin_a: sdhc2-pin-active { + clk { + pins = "sdc2_clk"; + drive-strength = <10>; + bias-disable; + }; + + cmd-data { + pins = "sdc2_cmd", "sdc2_data"; + drive-strength = <6>; + bias-pull-up; + }; + }; + }; }; -- cgit v1.2.3 From 76be038cab30796e3a27d34b5dd7e46169fcc78a Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 20 Oct 2015 21:57:49 -0700 Subject: ARM: dts: qcom: msm8974-honami: Specify charging parameters Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index e7e796888a21..37741725b7bd 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -371,6 +371,17 @@ &spmi_bus { pm8941@0 { + charger@1000 { + qcom,fast-charge-safe-current = <1500000>; + qcom,fast-charge-current-limit = <1500000>; + qcom,dc-current-limit = <1800000>; + qcom,fast-charge-safe-voltage = <4400000>; + qcom,fast-charge-high-threshold-voltage = <4350000>; + qcom,fast-charge-low-threshold-voltage = <3400000>; + qcom,auto-recharge-threshold-voltage = <4200000>; + qcom,minimum-input-voltage = <4300000>; + }; + gpios@c000 { boost_bypass_n_pin: boost-bypass { pins = "gpio21"; -- cgit v1.2.3 From 6a607e03bab31104e8ba53b38598b66d78b4f8ee Mon Sep 17 00:00:00 2001 From: John Stultz Date: Fri, 18 Sep 2015 13:31:12 +0100 Subject: devicetree: Add hardware rng entry to qcom-apq8064.dtsi Add devicetree data to add support for hw_rng support to the apq8064 dts. Tested on the Nexus7 (2013). Cc: Kumar Gala Cc: Stephen Boyd Cc: Srinivas Kandagatla Cc: devicetree@vger.kernel.org Reviewed-by: Stephen Boyd Signed-off-by: John Stultz Reviewed-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index a4c1762b53ea..42286c634d1e 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -336,6 +336,13 @@ }; }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; + }; + qcom,ssbi@500000 { compatible = "qcom,ssbi"; reg = <0x00500000 0x1000>; -- cgit v1.2.3 From eab5c6bc5210e34f34bd93191c19cfbe762c2cad Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 24 Sep 2015 18:24:59 -0700 Subject: dt-binding: soc: qcom: Add Qualcomm SMSM device tree documentation This documents a device tree binding for the Qualcomm Shared Memory State Machine. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../devicetree/bindings/soc/qcom/qcom,smsm.txt | 104 +++++++++++++++++++++ 1 file changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt new file mode 100644 index 000000000000..a6634c70850d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory State Machine + +The Shared Memory State Machine facilitates broadcasting of single bit state +information between the processors in a Qualcomm SoC. Each processor is +assigned 32 bits of state that can be modified. A processor can through a +matrix of bitmaps signal subscription of notifications upon changes to a +certain bit owned by a certain remote processor. + +- compatible: + Usage: required + Value type: + Definition: must be one of: + "qcom,smsm" + +- qcom,ipc-N: + Usage: required + Value type: + Definition: three entries specifying the outgoing ipc bit used for + signaling the N:th remote processor + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,local-host: + Usage: optional + Value type: + Definition: identifier of the local processor in the list of hosts, or + in other words specifier of the column in the subscription + matrix representing the local processor + defaults to host 0 + +- #address-cells: + Usage: required + Value type: + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: + Definition: must be 0 + += SUBNODES +Each processor's state bits are described by a subnode of the smsm device node. +Nodes can either be flagged as an interrupt-controller to denote a remote +processor's state bits or the local processors bits. The node names are not +important. + +- reg: + Usage: required + Value type: + Definition: specifies the offset, in words, of the first bit for this + entry + +- #qcom,state-cells: + Usage: required for local entry + Value type: + Definition: must be 1 - denotes bit number + +- interrupt-controller: + Usage: required for remote entries + Value type: + Definition: marks the entry as a interrupt-controller and the state bits + to belong to a remote processor + +- #interrupt-cells: + Usage: required for remote entries + Value type: + Definition: must be 2 - denotes bit number and IRQ flags + +- interrupts: + Usage: required for remote entries + Value type: + Definition: one entry specifying remote IRQ used by the remote processor + to signal changes of its state bits + + += EXAMPLE +The following example shows the SMEM setup for controlling properties of the +wireless processor, defined from the 8974 apps processor's point-of-view. It +encompasses one outbound entry and the outgoing interrupt for the wireless +processor. + +smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + qcom,ipc-3 = <&apcs 8 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,state-cells = <1>; + }; + + wcnss_smsm: wcnss@7 { + reg = <7>; + interrupts = <0 144 1>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; -- cgit v1.2.3 From 2f5de46c598caba441da75b679f43def795936e7 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 24 Sep 2015 18:25:00 -0700 Subject: dt-binding: soc: qcom: Introduce qcom, smp2p binding documentation Introduce binding documentation for the Qualcomm Shared Memory Point 2 Point protocol. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- .../devicetree/bindings/soc/qcom/qcom,smp2p.txt | 104 +++++++++++++++++++++ 1 file changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt new file mode 100644 index 000000000000..5cc82b8353d8 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory Point 2 Point binding + +The Shared Memory Point to Point (SMP2P) protocol facilitates communication of +a single 32-bit value between two processors. Each value has a single writer +(the local side) and a single reader (the remote side). Values are uniquely +identified in the system by the directed edge (local processor ID to remote +processor ID) and a string identifier. + +- compatible: + Usage: required + Value type: + Definition: must be one of: + "qcom,smp2p" + +- interrupts: + Usage: required + Value type: + Definition: one entry specifying the smp2p notification interrupt + +- qcom,ipc: + Usage: required + Value type: + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote end of the smp2p edge: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smem: + Usage: required + Value type: + Definition: two identifiers of the inbound and outbound smem items used + for this edge + +- qcom,local-pid: + Usage: required + Value type: + Definition: specifies the identfier of the local endpoint of this edge + +- qcom,remote-pid: + Usage: required + Value type: + Definition: specifies the identfier of the remote endpoint of this edge + += SUBNODES +Each SMP2P pair contain a set of inbound and outbound entries, these are +described in subnodes of the smp2p device node. The node names are not +important. + +- qcom,entry-name: + Usage: required + Value type: + Definition: specifies the name of this entry, for inbound entries this + will be used to match against the remotely allocated entry + and for outbound entries this name is used for allocating + entries + +- interrupt-controller: + Usage: required for incoming entries + Value type: + Definition: marks the entry as inbound; the node should be specified + as a two cell interrupt-controller as defined in + "../interrupt-controller/interrupts.txt" + If not specified this node will denote the outgoing entry + +- #interrupt-cells: + Usage: required for incoming entries + Value type: + Definition: must be 2 - denoting the bit in the entry and IRQ flags + +- #qcom,state-cells: + Usage: required for outgoing entries + Value type: + Definition: must be 1 - denoting the bit in the entry + += EXAMPLE +The following example shows the SMP2P setup with the wireless processor, +defined from the 8974 apps processor's point-of-view. It encompasses one +inbound and one outbound entry: + +wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <431>, <451>; + + interrupts = <0 143 1>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; -- cgit v1.2.3 From 24a9baf933dcee97864ba6b4412cb7d33facac7b Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 22 Oct 2015 11:13:48 -0700 Subject: ARM: dts: qcom: apq8064: Add hwmutex and SMEM nodes Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 42286c634d1e..a72e1226372b 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -11,6 +11,17 @@ compatible = "qcom,apq8064"; interrupt-parent = <&intc>; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smem_region: smem@80000000 { + reg = <0x80000000 0x200000>; + no-map; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -80,6 +91,19 @@ interrupts = <1 10 0x304>; }; + sfpb_mutex: hwmutex { + compatible = "qcom,sfpb-mutex"; + syscon = <&sfpb_wrapper_mutex 0x604 0x4>; + #hwlock-cells = <1>; + }; + + smem { + compatible = "qcom,smem"; + memory-region = <&smem_region>; + + hwlocks = <&sfpb_mutex 3>; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; @@ -156,6 +180,11 @@ }; }; + sfpb_wrapper_mutex: syscon@1200000 { + compatible = "syscon"; + reg = <0x01200000 0x8000>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; -- cgit v1.2.3 From 2bce6e26364108ce80903e9ec8702dd4ae17b0d5 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 22 Oct 2015 11:13:49 -0700 Subject: ARM: dts: qcom: apq8064: Declare all pm8921 regulators Consolidate all labeling of regulators into the core 8064 dtsi file to make them available from all other dts files. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts | 16 +++++----- arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 20 ++++++------- arch/arm/boot/dts/qcom-apq8064.dtsi | 46 +++++++++++++++++++++++++++++ 3 files changed, 64 insertions(+), 18 deletions(-) diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts index 03784f1366e5..21095dad7741 100644 --- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts +++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts @@ -54,7 +54,7 @@ /* Buck SMPS */ - pm8921_s1: s1 { + s1 { regulator-always-on; regulator-min-microvolt = <1225000>; regulator-max-microvolt = <1225000>; @@ -62,43 +62,43 @@ bias-pull-down; }; - pm8921_s3: s3 { + s3 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1400000>; qcom,switch-mode-frequency = <4800000>; }; - pm8921_s4: s4 { + s4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; qcom,switch-mode-frequency = <3200000>; }; - pm8921_s7: s7 { + s7 { regulator-min-microvolt = <1300000>; regulator-max-microvolt = <1300000>; qcom,switch-mode-frequency = <3200000>; }; - pm8921_l3: l3 { + l3 { regulator-min-microvolt = <3050000>; regulator-max-microvolt = <3300000>; bias-pull-down; }; - pm8921_l4: l4 { + l4 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1800000>; bias-pull-down; }; - pm8921_l5: l5 { + l5 { regulator-min-microvolt = <2750000>; regulator-max-microvolt = <3000000>; bias-pull-down; }; - pm8921_l23: l23 { + l23 { regulator-min-microvolt = <1700000>; regulator-max-microvolt = <1900000>; bias-pull-down; diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 11ac608b6d50..f40e93f09673 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -64,7 +64,7 @@ /* Buck SMPS */ - pm8921_s1: s1 { + s1 { regulator-always-on; regulator-min-microvolt = <1225000>; regulator-max-microvolt = <1225000>; @@ -72,55 +72,55 @@ bias-pull-down; }; - pm8921_s3: s3 { + s3 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1400000>; qcom,switch-mode-frequency = <4800000>; }; - pm8921_s4: s4 { + s4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; qcom,switch-mode-frequency = <3200000>; }; - pm8921_s7: s7 { + s7 { regulator-min-microvolt = <1300000>; regulator-max-microvolt = <1300000>; qcom,switch-mode-frequency = <3200000>; }; - pm8921_l3: l3 { + l3 { regulator-min-microvolt = <3050000>; regulator-max-microvolt = <3300000>; bias-pull-down; }; - pm8921_l4: l4 { + l4 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1800000>; bias-pull-down; }; - pm8921_l5: l5 { + l5 { regulator-min-microvolt = <2750000>; regulator-max-microvolt = <3000000>; bias-pull-down; }; - pm8921_l6: l6 { + l6 { regulator-min-microvolt = <2950000>; regulator-max-microvolt = <2950000>; bias-pull-down; }; - pm8921_l23: l23 { + l23 { regulator-min-microvolt = <1700000>; regulator-max-microvolt = <1900000>; bias-pull-down; }; - pm8921_lvs1: lvs1 { + lvs1 { bias-pull-down; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index a72e1226372b..e729fe6bea04 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -480,9 +480,55 @@ regulators { compatible = "qcom,rpm-pm8921-regulators"; + pm8921_s1: s1 {}; + pm8921_s2: s2 {}; + pm8921_s3: s3 {}; + pm8921_s4: s4 {}; + pm8921_s7: s7 {}; + pm8921_s8: s8 {}; + + pm8921_l1: l1 {}; + pm8921_l2: l2 {}; + pm8921_l3: l3 {}; + pm8921_l4: l4 {}; + pm8921_l5: l5 {}; + pm8921_l6: l6 {}; + pm8921_l7: l7 {}; + pm8921_l8: l8 {}; + pm8921_l9: l9 {}; + pm8921_l10: l10 {}; + pm8921_l11: l11 {}; + pm8921_l12: l12 {}; + pm8921_l14: l14 {}; + pm8921_l15: l15 {}; + pm8921_l16: l16 {}; + pm8921_l17: l17 {}; + pm8921_l18: l18 {}; + pm8921_l21: l21 {}; + pm8921_l22: l22 {}; + pm8921_l23: l23 {}; + pm8921_l24: l24 {}; + pm8921_l25: l25 {}; + pm8921_l26: l26 {}; + pm8921_l27: l27 {}; + pm8921_l28: l28 {}; + pm8921_l29: l29 {}; + + pm8921_lvs1: lvs1 {}; + pm8921_lvs2: lvs2 {}; + pm8921_lvs3: lvs3 {}; + pm8921_lvs4: lvs4 {}; + pm8921_lvs5: lvs5 {}; + pm8921_lvs6: lvs6 {}; + pm8921_lvs7: lvs7 {}; + + pm8921_usb_switch: usb-switch {}; + pm8921_hdmi_switch: hdmi-switch { bias-pull-down; }; + + pm8921_ncp: ncp {}; }; }; -- cgit v1.2.3 From 1099b26e2c9178f9b877e5535c49061e6165ecbd Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 22 Oct 2015 11:13:50 -0700 Subject: ARM: dts: qcom: apq8064: Introduce gsbi5 and gsbi5 serial node Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index e729fe6bea04..fc771b336027 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -320,6 +320,28 @@ }; }; + gsbi5: gsbi@1a200000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x03>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x100>, + <0x1a200000 0x03>; + interrupts = <0 154 0x0>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + }; + gsbi6: gsbi@16500000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; -- cgit v1.2.3 From 84b0b6bc3a3ea0460e5619302db46ac2197dc3bd Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Thu, 22 Oct 2015 11:13:51 -0700 Subject: ARM: dts: qcom: apq8064: Introduce Sony Xperia Z dts This introduces initial support for the Sony Xperia Z smartphone, including support for UART, MMC, USB gadget and physical buttons. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts | 436 +++++++++++++++++++++ 2 files changed, 437 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..2f691e7bf6fe 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -502,6 +502,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ + qcom-apq8064-sony-xperia-yuga.dtb \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts new file mode 100644 index 000000000000..06b3c76c3e41 --- /dev/null +++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts @@ -0,0 +1,436 @@ +#include "qcom-apq8064-v2.0.dtsi" +#include +#include +#include +#include + +/ { + model = "Sony Xperia Z"; + compatible = "sony,xperia-yuga", "qcom,apq8064"; + + aliases { + serial0 = &gsbi5_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_pin_a>; + + camera-focus { + label = "camera_focus"; + gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + camera-snapshot { + label = "camera_snapshot"; + gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + volume-down { + label = "volume_down"; + gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + + volume-up { + label = "volume_up"; + gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + }; + }; + + soc { + pinctrl@800000 { + gsbi5_uart_pin_a: gsbi5-uart-pin-active { + rx { + pins = "gpio52"; + function = "gsbi5"; + drive-strength = <2>; + bias-pull-up; + }; + + tx { + pins = "gpio51"; + function = "gsbi5"; + drive-strength = <4>; + bias-disable; + }; + }; + + sdcc1_pin_a: sdcc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strengh = <16>; + bias-disable; + }; + + cmd { + pins = "sdc1_cmd"; + drive-strengh = <10>; + bias-pull-up; + }; + + data { + pins = "sdc1_data"; + drive-strengh = <10>; + bias-pull-up; + }; + }; + + sdcc3_pin_a: sdcc3-pin-active { + clk { + pins = "sdc3_clk"; + drive-strengh = <8>; + bias-disable; + }; + + cmd { + pins = "sdc3_cmd"; + drive-strengh = <8>; + bias-pull-up; + }; + + data { + pins = "sdc3_data"; + drive-strengh = <8>; + bias-pull-up; + }; + }; + + sdcc3_cd_pin_a: sdcc3-cd-pin-active { + pins = "gpio26"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + }; + + + rpm@108000 { + regulators { + vin_l1_l2_l12_l18-supply = <&pm8921_s4>; + vin_lvs_1_3_6-supply = <&pm8921_s4>; + vin_lvs_4_5_7-supply = <&pm8921_s4>; + vin_ncp-supply = <&pm8921_l6>; + vin_lvs2-supply = <&pm8921_s4>; + vin_l24-supply = <&pm8921_s1>; + vin_l25-supply = <&pm8921_s1>; + vin_l27-supply = <&pm8921_s7>; + vin_l28-supply = <&pm8921_s7>; + + /* Buck SMPS */ + s1 { + regulator-always-on; + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + qcom,switch-mode-frequency = <3200000>; + bias-pull-down; + }; + + s2 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + s3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1150000>; + qcom,switch-mode-frequency = <4800000>; + bias-pull-down; + }; + + s4 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + qcom,force-mode = ; + }; + + s7 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <3200000>; + }; + + s8 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + qcom,switch-mode-frequency = <1600000>; + }; + + /* PMOS LDO */ + l1 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + bias-pull-down; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + + l3 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + bias-pull-down; + }; + + l4 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + l5 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + l6 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + l7 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + l8 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + bias-pull-down; + }; + + l9 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + bias-pull-down; + }; + + l10 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + bias-pull-down; + }; + + l11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + bias-pull-down; + }; + + l12 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + l16 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + bias-pull-down; + }; + + l17 { + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + bias-pull-down; + }; + + l18 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + + l21 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + bias-pull-down; + }; + + l22 { + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + + l23 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + l24 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1150000>; + bias-pull-down; + }; + + l25 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + bias-pull-down; + }; + + l27 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + l28 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + bias-pull-down; + }; + + l29 { + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + bias-pull-down; + }; + + /* Low Voltage Switch */ + lvs1 { + bias-pull-down; + }; + + lvs2 { + bias-pull-down; + }; + + lvs3 { + bias-pull-down; + }; + + lvs4 { + bias-pull-down; + }; + + lvs5 { + bias-pull-down; + }; + + lvs6 { + bias-pull-down; + }; + + lvs7 { + bias-pull-down; + }; + + usb-switch {}; + + hdmi-switch {}; + + ncp { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + }; + }; + }; + + qcom,ssbi@500000 { + pmic@0 { + gpio@150 { + gpio_keys_pin_a: gpio-keys-pin-active { + pins = "gpio3", "gpio4", "gpio29", "gpio35"; + function = "normal"; + + bias-pull-up; + drive-push-pull; + input-enable; + power-source = <2>; + qcom,drive-strength = ; + qcom,pull-up-strength = <0>; + }; + }; + }; + }; + + phy@12500000 { + status = "okay"; + vddcx-supply = <&pm8921_s3>; + v3p3-supply = <&pm8921_l3>; + v1p8-supply = <&pm8921_l4>; + }; + + gadget@12500000 { + status = "okay"; + }; + + gsbi@1a200000 { + status = "ok"; + qcom,mode = ; + + serial@1a240000 { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_pin_a>; + }; + }; + + amba { + sdcc1: sdcc@12400000 { + status = "okay"; + + vmmc-supply = <&pm8921_l5>; + vqmmc-supply = <&pm8921_s4>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdcc1_pin_a>; + }; + + sdcc3: sdcc@12180000 { + status = "okay"; + + vmmc-supply = <&pm8921_l6>; + cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdcc3_pin_a>, <&sdcc3_cd_pin_a>; + }; + }; + }; +}; -- cgit v1.2.3 From c40225b50fc523437da0601764da013b499cb596 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 26 Oct 2015 18:26:53 -0700 Subject: arm: dts: qcom: Add board clocks These clocks are fixed rate board sources that should be in DT. Add them. Cc: Georgi Djakov Signed-off-by: Stephen Boyd Reviewed-by: Andy Gross Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8960.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi index 134cd91d68ec..51a40d84145c 100644 --- a/arch/arm/boot/dts/qcom-msm8960.dtsi +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi @@ -49,6 +49,29 @@ qcom,no-pc-write; }; + clocks { + cxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + clock-output-names = "cxo_board"; + }; + + pxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + clock-output-names = "pxo_board"; + }; + + sleep_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "sleep_clk"; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From 9208b5178bdaca21a1101ac61daa3d610e5435bc Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Fri, 20 Nov 2015 15:31:18 -0800 Subject: arm: dts: qcom: Update ifc6540 compat for qcom boot format The ifc6540 is an sbc (single board computer) board, so update the compatible field accordingly. Signed-off-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8084-ifc6540.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts index c9c2b769554f..32aaa9d45228 100644 --- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts +++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts @@ -3,7 +3,7 @@ / { model = "Qualcomm APQ8084/IFC6540"; - compatible = "qcom,apq8084-ifc6540", "qcom,apq8084"; + compatible = "qcom,apq8084-sbc", "qcom,apq8084"; aliases { serial0 = &blsp2_uart2; -- cgit v1.2.3 From 134c544e9d1b56075c807e6152f2564ad1997327 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Fri, 20 Nov 2015 15:31:20 -0800 Subject: arm: dts: qcom: Add aliases for PMICs Add an alias for the PMICs found on qcom based SoCs so that the newly updated dtbTool can find the PMIC compatible string and add the pmic-id element to the QCDT header. Signed-off-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8074-dragonboard.dts | 2 ++ arch/arm/boot/dts/qcom-apq8084-ifc6540.dts | 1 + arch/arm/boot/dts/qcom-apq8084-mtp.dts | 1 + arch/arm/boot/dts/qcom-pm8841.dtsi | 8 ++++---- arch/arm/boot/dts/qcom-pm8941.dtsi | 8 ++++---- arch/arm/boot/dts/qcom-pma8084.dtsi | 8 ++++---- 6 files changed, 16 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts index 835bdc71c5ba..c0e205315042 100644 --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts @@ -8,6 +8,8 @@ aliases { serial0 = &blsp1_uart2; + usid0 = &pm8941_0; + usid4 = &pm8841_0; }; chosen { diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts index 32aaa9d45228..2052b84a77c6 100644 --- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts +++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts @@ -7,6 +7,7 @@ aliases { serial0 = &blsp2_uart2; + usid0 = &pma8084_0; }; chosen { diff --git a/arch/arm/boot/dts/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom-apq8084-mtp.dts index 3016c7048d44..d174d15bcf70 100644 --- a/arch/arm/boot/dts/qcom-apq8084-mtp.dts +++ b/arch/arm/boot/dts/qcom-apq8084-mtp.dts @@ -7,6 +7,7 @@ aliases { serial0 = &blsp2_uart2; + usid0 = &pma8084_0; }; chosen { diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi index 8f1a0b162017..523bee959f98 100644 --- a/arch/arm/boot/dts/qcom-pm8841.dtsi +++ b/arch/arm/boot/dts/qcom-pm8841.dtsi @@ -3,8 +3,8 @@ &spmi_bus { - usid4: pm8841@4 { - compatible = "qcom,spmi-pmic"; + pm8841_0: pm8841@4 { + compatible = "qcom,pm8841", "qcom,spmi-pmic"; reg = <0x4 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; @@ -27,8 +27,8 @@ }; }; - usid5: pm8841@5 { - compatible = "qcom,spmi-pmic"; + pm8841_1: pm8841@5 { + compatible = "qcom,pm8841", "qcom,spmi-pmic"; reg = <0x5 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi index b0d443999fcc..02d674f76591 100644 --- a/arch/arm/boot/dts/qcom-pm8941.dtsi +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -4,8 +4,8 @@ &spmi_bus { - usid0: pm8941@0 { - compatible ="qcom,spmi-pmic"; + pm8941_0: pm8941@0 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; reg = <0x0 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; @@ -153,8 +153,8 @@ }; }; - usid1: pm8941@1 { - compatible = "qcom,spmi-pmic"; + pm8941_1: pm8941@1 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; reg = <0x1 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi index 5e240ccc08b7..10b8f9e6d60b 100644 --- a/arch/arm/boot/dts/qcom-pma8084.dtsi +++ b/arch/arm/boot/dts/qcom-pma8084.dtsi @@ -4,8 +4,8 @@ &spmi_bus { - usid0: pma8084@0 { - compatible = "qcom,spmi-pmic"; + pma8084_0: pma8084@0 { + compatible = "qcom,pma8084", "qcom,spmi-pmic"; reg = <0x0 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; @@ -101,8 +101,8 @@ }; }; - usid1: pma8084@1 { - compatible = "qcom,spmi-pmic"; + pma8084_1: pma8084@1 { + compatible = "qcom,pma8084", "qcom,spmi-pmic"; reg = <0x1 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; -- cgit v1.2.3 From 2ca9c2a4c1ef5faac27076475261788302158722 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Fri, 20 Nov 2015 17:49:46 -0800 Subject: arm: dts: qcom: Add generic PMIC gpio/MPP compat strings Add the generic compatible strings for the PMIC gpio and MPP modules found on qcom based PMICs. Cc: Cc: "Ivan T. Ivanov" Cc: Bjorn Andersson Cc: Rob Herring Signed-off-by: Stephen Boyd Reviewed-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 6 ++++-- arch/arm/boot/dts/qcom-pm8841.dtsi | 2 +- arch/arm/boot/dts/qcom-pm8941.dtsi | 4 ++-- arch/arm/boot/dts/qcom-pma8084.dtsi | 4 ++-- 4 files changed, 9 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index fc771b336027..e6c7476036a4 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -410,7 +410,8 @@ pm8921_gpio: gpio@150 { - compatible = "qcom,pm8921-gpio"; + compatible = "qcom,pm8921-gpio", + "qcom,ssbi-gpio"; reg = <0x150>; interrupts = <192 1>, <193 1>, <194 1>, <195 1>, <196 1>, <197 1>, @@ -434,7 +435,8 @@ }; pm8921_mpps: mpps@50 { - compatible = "qcom,pm8921-mpp"; + compatible = "qcom,pm8921-mpp", + "qcom,ssbi-mpp"; reg = <0x50>; gpio-controller; #gpio-cells = <2>; diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi index 523bee959f98..9f357f68713c 100644 --- a/arch/arm/boot/dts/qcom-pm8841.dtsi +++ b/arch/arm/boot/dts/qcom-pm8841.dtsi @@ -10,7 +10,7 @@ #size-cells = <0>; pm8841_mpps: mpps@a000 { - compatible = "qcom,pm8841-mpp"; + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp"; reg = <0xa000 0x400>; gpio-controller; #gpio-cells = <2>; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi index 02d674f76591..a149c6f13870 100644 --- a/arch/arm/boot/dts/qcom-pm8941.dtsi +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -48,7 +48,7 @@ }; pm8941_gpios: gpios@c000 { - compatible = "qcom,pm8941-gpio"; + compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio"; reg = <0xc000 0x2400>; gpio-controller; #gpio-cells = <2>; @@ -91,7 +91,7 @@ }; pm8941_mpps: mpps@a000 { - compatible = "qcom,pm8941-mpp"; + compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp"; reg = <0xa000 0x800>; gpio-controller; #gpio-cells = <2>; diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi index 10b8f9e6d60b..4e9bd3f88473 100644 --- a/arch/arm/boot/dts/qcom-pma8084.dtsi +++ b/arch/arm/boot/dts/qcom-pma8084.dtsi @@ -19,7 +19,7 @@ }; pma8084_gpios: gpios@c000 { - compatible = "qcom,pma8084-gpio"; + compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio"; reg = <0xc000 0x1600>; gpio-controller; #gpio-cells = <2>; @@ -48,7 +48,7 @@ }; pma8084_mpps: mpps@a000 { - compatible = "qcom,pma8084-mpp"; + compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp"; reg = <0xa000 0x800>; gpio-controller; #gpio-cells = <2>; -- cgit v1.2.3 From 7026d15c7ac10dda22a9f3eda508459c924d7142 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Mon, 23 Nov 2015 11:04:07 -0800 Subject: ARM: dts: qcom: msm8974: Disable wled and move it to honami The properties specified in the wled node could harm connected hardware, so move the properties to Honami and disable the platform node. Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts | 13 +++++++++++++ arch/arm/boot/dts/qcom-pm8941.dtsi | 9 ++------- 2 files changed, 15 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 37741725b7bd..a0398b69f4f2 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -403,4 +403,17 @@ qcom,vset-millivolts = <3000>; }; }; + + pm8941@1 { + wled@d800 { + status = "ok"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + }; + }; }; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi index a149c6f13870..ca53a5947437 100644 --- a/arch/arm/boot/dts/qcom-pm8941.dtsi +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -159,17 +159,12 @@ #address-cells = <1>; #size-cells = <0>; - wled@d800 { + pm8941_wled: wled@d800 { compatible = "qcom,pm8941-wled"; reg = <0xd800 0x100>; label = "backlight"; - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; + status = "disabled"; }; }; }; -- cgit v1.2.3 From 580df59fa74e53bb71c21fb4e97d74ca3c9665b2 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Mon, 23 Nov 2015 21:54:34 -0800 Subject: ARM: dts: qcom: msm8974: Add i2c8 node Signed-off-by: Bjorn Andersson Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8974.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 753bdfddd46e..dfdafdcb8aae 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -319,6 +319,17 @@ interrupts = <0 208 0>; }; + blsp_i2c8: i2c@f9964000 { + status = "disabled"; + compatible = "qcom,i2c-qup-v2.1.1"; + reg = <0xf9964000 0x1000>; + interrupts = <0 102 IRQ_TYPE_NONE>; + clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + }; + blsp_i2c11: i2c@f9967000 { status = "disabled"; compatible = "qcom,i2c-qup-v2.1.1"; -- cgit v1.2.3 From eb0fc0d6ae99305a5aecbcf8a67cce838547d638 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Mon, 30 Nov 2015 11:41:39 +0100 Subject: dt-bindings: soc: Add supplies for Mediatek SCPSYS unit The power domains in the SCPSYS unit are supplied by regulators. Add the properties for them to the binding document. Signed-off-by: Sascha Hauer Cc: devicetree@vger.kernel.org Acked-by: Rob Herring Signed-off-by: Matthias Brugger --- Documentation/devicetree/bindings/soc/mediatek/scpsys.txt | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index a6c8afc8385a..e8f15e34027f 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -21,6 +21,18 @@ Required properties: These are the clocks which hardware needs to be enabled before enabling certain power domains. +Optional properties: +- vdec-supply: Power supply for the vdec power domain +- venc-supply: Power supply for the venc power domain +- isp-supply: Power supply for the isp power domain +- mm-supply: Power supply for the mm power domain +- venc_lt-supply: Power supply for the venc_lt power domain +- audio-supply: Power supply for the audio power domain +- usb-supply: Power supply for the usb power domain +- mfg_async-supply: Power supply for the mfg_async power domain +- mfg_2d-supply: Power supply for the mfg_2d power domain +- mfg-supply: Power supply for the mfg power domain + Example: scpsys: scpsys@10006000 { -- cgit v1.2.3 From 832dae1fcb72adff9e28eee9b768786fc7a0e0a9 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:12 +0100 Subject: ARM: shmobile: koelsch dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-koelsch.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index 50d7b17c6ebd..c94a0fb807a2 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -54,7 +54,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif0; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From b575f99486b938a1720d961e73ec7aabb259ffd0 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:06 +0100 Subject: ARM: shmobile: alt dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-alt.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 767d9224d6cc..2394e4883786 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -21,7 +21,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif2; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From 6deac6d0b931825081c5894d186abd1c6ec4c524 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:07 +0100 Subject: ARM: shmobile: ape6evm dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a73a4-ape6evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index 9b7eabd3eba3..590257095700 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -23,7 +23,7 @@ chosen { bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp rw"; - stdout-path = &scifa0; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From f84a9cbb173946754712b366524fc4f5fb744424 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:09 +0100 Subject: ARM: shmobile: bockw dts: Update console parameters Drop the "console=" parameter from the kernel command line, as it's no longer needed for DT-based platforms. Add serial port config to chosen/stdout-path. Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778-bockw.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index 158ad94fd4d1..b1aa02599229 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -28,8 +28,8 @@ }; chosen { - bootargs = "console=ttySC0,115200 ignore_loglevel ip=dhcp root=/dev/nfs rw"; - stdout-path = &scif0; + bootargs = "ignore_loglevel ip=dhcp root=/dev/nfs rw"; + stdout-path = "serial0:115200n8"; }; memory { -- cgit v1.2.3 From 16010a3e13f7ede016ae9bdc5dbffa96a0a49d3b Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:11 +0100 Subject: ARM: shmobile: gose dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793-gose.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index d842ce77b7c8..3e3122490650 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -24,7 +24,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif0; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From 5995e9f0c58a7053fa56e93fd8366e68ee3242f7 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:18 +0100 Subject: ARM: shmobile: silk dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-silk.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index 58f0ddf21c17..5a8dcac37c8e 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -24,7 +24,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif2; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From bf20476991bbfa183e778463d0eadaed6111b989 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:17 +0100 Subject: ARM: shmobile: porter dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-porter.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index f2dd5356eac8..71ba7b6b3a33 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -22,7 +22,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif0; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From 57d19f813177243382fbdc14fef06d19f0956228 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 8 Dec 2015 18:54:15 +0100 Subject: ARM: shmobile: lager dts: Add serial port config to chosen/stdout-path Signed-off-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790-lager.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index c46295afb08a..44ba69b974a2 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -53,7 +53,7 @@ chosen { bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; - stdout-path = &scif0; + stdout-path = "serial0:115200n8"; }; memory@40000000 { -- cgit v1.2.3 From 222ca7838214100fb2f1917bae78405bae7a2869 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 27 Nov 2015 10:52:45 +0900 Subject: ARM: shmobile: r8a7793: Add missing serial devices to DT Instantiate all serial devices in r8a7793 device tree and set them as disabled by default. Based on similar work for the r8a7791 by Laurent Pinchart. Cc: Laurent Pinchart Signed-off-by: Simon Horman Acked-by: Geert Uytterhoeven Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 179 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 177 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 4c74a9229e71..309b33d60001 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -297,6 +297,96 @@ dma-channels = <15>; }; + scifa0: serial@e6c40000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c40000 0 64>; + interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFA0>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifa1: serial@e6c50000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c50000 0 64>; + interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFA1>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifa2: serial@e6c60000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c60000 0 64>; + interrupts = <0 151 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFA2>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifa3: serial@e6c70000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c70000 0 64>; + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7793_CLK_SCIFA3>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifa4: serial@e6c78000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c78000 0 64>; + interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7793_CLK_SCIFA4>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifa5: serial@e6c80000 { + compatible = "renesas,scifa-r8a7793", "renesas,scifa"; + reg = <0 0xe6c80000 0 64>; + interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7793_CLK_SCIFA5>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifb0: serial@e6c20000 { + compatible = "renesas,scifb-r8a7793", "renesas,scifb"; + reg = <0 0xe6c20000 0 64>; + interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFB0>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifb1: serial@e6c30000 { + compatible = "renesas,scifb-r8a7793", "renesas,scifb"; + reg = <0 0xe6c30000 0 64>; + interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFB1>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scifb2: serial@e6ce0000 { + compatible = "renesas,scifb-r8a7793", "renesas,scifb"; + reg = <0 0xe6ce0000 0 64>; + interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7793_CLK_SCIFB2>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a7793", "renesas,scif"; reg = <0 0xe6e60000 0 64>; @@ -317,6 +407,76 @@ status = "disabled"; }; + scif2: serial@e6e58000 { + compatible = "renesas,scif-r8a7793", "renesas,scif"; + reg = <0 0xe6e58000 0 64>; + interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_SCIF2>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif3: serial@e6ea8000 { + compatible = "renesas,scif-r8a7793", "renesas,scif"; + reg = <0 0xe6ea8000 0 64>; + interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_SCIF3>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif4: serial@e6ee0000 { + compatible = "renesas,scif-r8a7793", "renesas,scif"; + reg = <0 0xe6ee0000 0 64>; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_SCIF4>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + scif5: serial@e6ee8000 { + compatible = "renesas,scif-r8a7793", "renesas,scif"; + reg = <0 0xe6ee8000 0 64>; + interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_SCIF5>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + hscif0: serial@e62c0000 { + compatible = "renesas,hscif-r8a7793", "renesas,hscif"; + reg = <0 0xe62c0000 0 96>; + interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_HSCIF0>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + hscif1: serial@e62c8000 { + compatible = "renesas,hscif-r8a7793", "renesas,hscif"; + reg = <0 0xe62c8000 0 96>; + interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_HSCIF1>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + hscif2: serial@e62d0000 { + compatible = "renesas,hscif-r8a7793", "renesas,hscif"; + reg = <0 0xe62d0000 0 96>; + interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7793_CLK_HSCIF2>; + clock-names = "sci_ick"; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + ether: ethernet@ee700000 { compatible = "renesas,ether-r8a7793"; reg = <0 0xee700000 0 0x400>; @@ -529,12 +689,17 @@ mstp2_clks: mstp2_clks@e6150138 { compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>; - clocks = <&zs_clk>, <&zs_clk>; + clocks = <&mp_clk>, <&mp_clk>, <&mp_clk>, <&mp_clk>, + <&mp_clk>, <&mp_clk>, <&zs_clk>, <&zs_clk>; #clock-cells = <1>; clock-indices = < + R8A7793_CLK_SCIFA2 R8A7793_CLK_SCIFA1 R8A7793_CLK_SCIFA0 + R8A7793_CLK_SCIFB0 R8A7793_CLK_SCIFB1 R8A7793_CLK_SCIFB2 R8A7793_CLK_SYS_DMAC1 R8A7793_CLK_SYS_DMAC0 >; - clock-output-names = "sys-dmac1", "sys-dmac0"; + clock-output-names = + "scifa2", "scifa1", "scifa0", "scifb0", + "scifb1", "scifb2", "sys-dmac1", "sys-dmac0"; }; mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7793-mstp-clocks", @@ -633,6 +798,16 @@ "gpio3", "gpio2", "gpio1", "gpio0", "qspi_mod"; }; + mstp11_clks: mstp11_clks@e615099c { + compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe615099c 0 4>, <0 0xe61509ac 0 4>; + clocks = <&mp_clk>, <&mp_clk>, <&mp_clk>; + #clock-cells = <1>; + clock-indices = < + R8A7793_CLK_SCIFA3 R8A7793_CLK_SCIFA4 R8A7793_CLK_SCIFA5 + >; + clock-output-names = "scifa3", "scifa4", "scifa5"; + }; }; ipmmu_sy0: mmu@e6280000 { -- cgit v1.2.3 From c807d6e2046347d679e992fe4fe4b1133638a464 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Thu, 10 Dec 2015 21:36:29 +0800 Subject: ARM: dts: sun9i: cubieboard4: Enable LEDs The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 6484dcf69873..8791d49bed2d 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -62,9 +62,31 @@ stdout-path = "serial0:115200n8"; }; + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_cubieboard4>; + + green { + label = "cubieboard4:green:usr"; + gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */ + }; + + red { + label = "cubieboard4:red:usr"; + gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + }; + }; }; &pio { + led_pins_cubieboard4: led-pins@0 { + allwinner,pins = "PH6", "PH17"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 { allwinner,pins = "PH18"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From 62b4b20cd2bca593c89896711cac7c913be67e80 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Thu, 10 Dec 2015 21:36:30 +0800 Subject: ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver The Cubieboard4 has a consumer IR receiver. Enable it in the DT. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 8791d49bed2d..8c26b556e82a 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -114,6 +114,10 @@ status = "okay"; }; +&r_ir { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.3 From 6f353f61e29a8fc919b5afa1277a98277782f5b1 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Thu, 10 Dec 2015 21:36:31 +0800 Subject: ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller The Reduced Serial Bus (RSB) controller is used to talk to the 3 companion ICs (2 PMICs, 1 RTC/codec IC) on the board. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 8c26b556e82a..382bd9fc5647 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -118,6 +118,10 @@ status = "okay"; }; +&r_rsb { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.3 From 4b0f88796bd3d19331550dad2a9d958091f874a2 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 11 Dec 2015 10:07:38 +0900 Subject: ARM: shmobile: r8a7793: Describe DMA for the serial ports Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes. Based on similar work for the r8a7791 by Geert Uytterhoeven. Signed-off-by: Simon Horman Acked-by: Geert Uytterhoeven --- arch/arm/boot/dts/r8a7793.dtsi | 36 ++++++++++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index 309b33d60001..df607a92b2ed 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -303,6 +303,8 @@ interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFA0>; clock-names = "sci_ick"; + dmas = <&dmac0 0x21>, <&dmac0 0x22>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -313,6 +315,8 @@ interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFA1>; clock-names = "sci_ick"; + dmas = <&dmac0 0x25>, <&dmac0 0x26>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -323,6 +327,8 @@ interrupts = <0 151 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFA2>; clock-names = "sci_ick"; + dmas = <&dmac0 0x27>, <&dmac0 0x28>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -333,6 +339,8 @@ interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp11_clks R8A7793_CLK_SCIFA3>; clock-names = "sci_ick"; + dmas = <&dmac0 0x1b>, <&dmac0 0x1c>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -343,6 +351,8 @@ interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp11_clks R8A7793_CLK_SCIFA4>; clock-names = "sci_ick"; + dmas = <&dmac0 0x1f>, <&dmac0 0x20>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -353,6 +363,8 @@ interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp11_clks R8A7793_CLK_SCIFA5>; clock-names = "sci_ick"; + dmas = <&dmac0 0x23>, <&dmac0 0x24>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -363,6 +375,8 @@ interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFB0>; clock-names = "sci_ick"; + dmas = <&dmac0 0x3d>, <&dmac0 0x3e>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -373,6 +387,8 @@ interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFB1>; clock-names = "sci_ick"; + dmas = <&dmac0 0x19>, <&dmac0 0x1a>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -383,6 +399,8 @@ interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7793_CLK_SCIFB2>; clock-names = "sci_ick"; + dmas = <&dmac0 0x1d>, <&dmac0 0x1e>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -393,6 +411,8 @@ interrupts = <0 152 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF0>; clock-names = "sci_ick"; + dmas = <&dmac0 0x29>, <&dmac0 0x2a>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -403,6 +423,8 @@ interrupts = <0 153 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF1>; clock-names = "sci_ick"; + dmas = <&dmac0 0x2d>, <&dmac0 0x2e>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -413,6 +435,8 @@ interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF2>; clock-names = "sci_ick"; + dmas = <&dmac0 0x2b>, <&dmac0 0x2c>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -423,6 +447,8 @@ interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF3>; clock-names = "sci_ick"; + dmas = <&dmac0 0x2f>, <&dmac0 0x30>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -433,6 +459,8 @@ interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF4>; clock-names = "sci_ick"; + dmas = <&dmac0 0xfb>, <&dmac0 0xfc>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -443,6 +471,8 @@ interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_SCIF5>; clock-names = "sci_ick"; + dmas = <&dmac0 0xfd>, <&dmac0 0xfe>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -453,6 +483,8 @@ interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_HSCIF0>; clock-names = "sci_ick"; + dmas = <&dmac0 0x39>, <&dmac0 0x3a>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -463,6 +495,8 @@ interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_HSCIF1>; clock-names = "sci_ick"; + dmas = <&dmac0 0x4d>, <&dmac0 0x4e>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; @@ -473,6 +507,8 @@ interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7793_CLK_HSCIF2>; clock-names = "sci_ick"; + dmas = <&dmac0 0x3b>, <&dmac0 0x3c>; + dma-names = "tx", "rx"; power-domains = <&cpg_clocks>; status = "disabled"; }; -- cgit v1.2.3 From 15228f04de82c2f6d893926423b71c9ce8c4200e Mon Sep 17 00:00:00 2001 From: Karsten Merker Date: Thu, 10 Dec 2015 21:31:59 +0100 Subject: ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys The Olimex A20-SOM-EVB is an evaluation board for the Olimex A20-SOM system-on-module. It provides a set of android-style buttons (labeled "VOL+", "VOL-", "MENU", "SEARCH", "HOME", "ESC" and "ENTER") which are connected to a low-resolution ADC via a resistor network. This patch adds appropriate button definitions to the board dts. The voltages assigned to the keys are specified in the board schematics published by the manufacturer. Signed-off-by: Karsten Merker Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts | 56 ++++++++++++++++++++++++++ 1 file changed, 56 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts index a91879ed07f8..beccb25e88bf 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -1,5 +1,6 @@ /* * Copyright 2015 - Marcus Cooper + * Copyright 2015 - Karsten Merker * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -45,6 +46,7 @@ #include "sunxi-common-regulators.dtsi" #include +#include #include #include @@ -114,6 +116,60 @@ }; }; +&lradc { + vref-supply = <®_vcc3v0>; + status = "okay"; + + button@190 { + label = "Volume Up"; + linux,code = ; + channel = <0>; + voltage = <190000>; + }; + + button@390 { + label = "Volume Down"; + linux,code = ; + channel = <0>; + voltage = <390000>; + }; + + button@600 { + label = "Menu"; + linux,code = ; + channel = <0>; + voltage = <600000>; + }; + + button@800 { + label = "Search"; + linux,code = ; + channel = <0>; + voltage = <800000>; + }; + + button@980 { + label = "Home"; + linux,code = ; + channel = <0>; + voltage = <980000>; + }; + + button@1180 { + label = "Esc"; + linux,code = ; + channel = <0>; + voltage = <1180000>; + }; + + button@1400 { + label = "Enter"; + linux,code = ; + channel = <0>; + voltage = <1400000>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; -- cgit v1.2.3 From 2367cee5fda1e9ebc605b13175492b31030acd9d Mon Sep 17 00:00:00 2001 From: Karsten Merker Date: Thu, 10 Dec 2015 21:32:00 +0100 Subject: ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket) The Olimex A20-SOM-EVB is an evaluation board for the Olimex A20-SOM system-on-module. The baseboard provides a full-size SD socket (connected to mmc3) in addition to the micro-SD socket on the SOM itself (which is connected to mmc0). Enable the mmc3 controller in the dts. Signed-off-by: Karsten Merker Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts index beccb25e88bf..c3c626b2cfa2 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -180,6 +180,16 @@ status = "okay"; }; +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olimex_som_evb>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */ + cd-inverted; + status = "okay"; +}; + &ohci0 { status = "okay"; }; @@ -202,6 +212,13 @@ allwinner,drive = ; allwinner,pull = ; }; + + mmc3_cd_pin_olimex_som_evb: mmc3_cd_pin@0 { + allwinner,pins = "PH0"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; }; ®_ahci_5v { -- cgit v1.2.3 From 69c923743640deac686f0a2e7d5fc2cf82dc428c Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Thu, 10 Dec 2015 13:46:37 +0800 Subject: ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846 According to the schematic, the name of REG8 should be vcc_tp, rather than vcca_tp. Signed-off-by: Chris Zhong Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-evb-act8846.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index 43949a6771f0..53d8b08cb199 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -152,7 +152,7 @@ regulator-always-on; }; - vcca_tp: REG8 { + vcc_tp: REG8 { regulator-name = "VCCA_TP"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; -- cgit v1.2.3 From 662513a14c9dd1ba2b4d5928d6eae443744edefc Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Thu, 10 Dec 2015 13:46:38 +0800 Subject: ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846 vcc_wl and vcc_lcd are 2 gpio switches for rk3288-evb-act8846 board. Signed-off-by: Chris Zhong Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-evb-act8846.dts | 34 ++++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index 53d8b08cb199..7b768b7e357f 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -43,6 +43,26 @@ / { compatible = "rockchip,rk3288-evb-act8846", "rockchip,rk3288"; + + vcc_lcd: vcc-lcd { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio7 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_en>; + regulator-name = "vcc_lcd"; + vin-supply = <&vcc_io>; + }; + + vcc_wl: vcc-wl { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio7 9 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_pwr>; + regulator-name = "vcc_wl"; + vin-supply = <&vcc_18>; + }; }; &cpu0 { @@ -189,3 +209,17 @@ }; }; }; + +&pinctrl { + lcd { + lcd_en: lcd-en { + rockchip,pins = <7 3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + wifi { + wifi_pwr: wifi-pwr { + rockchip,pins = <7 9 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; -- cgit v1.2.3 From b04061e6599be87a23e7bc06f3bf4d3b3e325ff8 Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Thu, 10 Dec 2015 13:46:39 +0800 Subject: ARM: dts: rockchip: move the public part to rk3288-evb common Rk3288-evb-act8846 and rk3288-evb-rk808 are the power boards of rk3288-evb, they provide the same power supply interface to the motherboard. Sort out them, put the public part to rk3288-evb.dtsi, such as gmac and cpu-supply, leaving only the power section. Signed-off-by: Chris Zhong Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-evb-act8846.dts | 4 ---- arch/arm/boot/dts/rk3288-evb-rk808.dts | 27 ----------------------- arch/arm/boot/dts/rk3288-evb.dtsi | 37 +++++++++++++++++++++++++++----- 3 files changed, 32 insertions(+), 36 deletions(-) diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index 7b768b7e357f..e6621471753b 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -65,10 +65,6 @@ }; }; -&cpu0 { - cpu0-supply = <&vdd_cpu>; -}; - &i2c0 { clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts index 18eb6cb495f4..736b08b0bfdd 100644 --- a/arch/arm/boot/dts/rk3288-evb-rk808.dts +++ b/arch/arm/boot/dts/rk3288-evb-rk808.dts @@ -43,17 +43,6 @@ / { compatible = "rockchip,rk3288-evb-rk808", "rockchip,rk3288"; - - ext_gmac: external-gmac-clock { - compatible = "fixed-clock"; - clock-frequency = <125000000>; - clock-output-names = "ext_gmac"; - #clock-cells = <0>; - }; -}; - -&cpu0 { - cpu0-supply = <&vdd_cpu>; }; &i2c0 { @@ -244,19 +233,3 @@ }; }; }; - -&gmac { - phy-supply = <&vcc_phy>; - phy-mode = "rgmii"; - clock_in_out = "input"; - snps,reset-gpio = <&gpio4 7 0>; - snps,reset-active-low; - snps,reset-delays-us = <0 10000 1000000>; - assigned-clocks = <&cru SCLK_MAC>; - assigned-clock-parents = <&ext_gmac>; - pinctrl-names = "default"; - pinctrl-0 = <&rgmii_pins>; - tx_delay = <0x30>; - rx_delay = <0x10>; - status = "ok"; -}; diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi index f6d2e7894b05..4faabdb65868 100644 --- a/arch/arm/boot/dts/rk3288-evb.dtsi +++ b/arch/arm/boot/dts/rk3288-evb.dtsi @@ -89,6 +89,13 @@ pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>; }; + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + gpio-keys { compatible = "gpio-keys"; #address-cells = <1>; @@ -160,6 +167,10 @@ }; }; +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + &emmc { broken-cd; bus-width = <8>; @@ -172,11 +183,6 @@ status = "okay"; }; -&hdmi { - ddc-i2c-bus = <&i2c5>; - status = "okay"; -}; - &sdmmc { bus-width = <4>; cap-mmc-highspeed; @@ -191,6 +197,27 @@ vqmmc-supply = <&vccio_sd>; }; +&gmac { + phy-supply = <&vcc_phy>; + phy-mode = "rgmii"; + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + &i2c0 { status = "okay"; }; -- cgit v1.2.3 From a1c2e133d26688a5783e1264cb6865b5d2bd9181 Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Wed, 2 Dec 2015 19:12:21 +0800 Subject: ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board In general, the logic voltage is affected by ddr frequency factors. We should fix the correct voltage range since assuemd that we have the ddr frequency driver in mainline in the future. AFAIK, the 1.8v voltage is used by the SD3.0 card. Signed-off-by: Caesar Wang Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-evb-act8846.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index e6621471753b..452ca2441e84 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -135,8 +135,8 @@ vdd_log: REG3 { regulator-name = "VDD_LOG"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1500000>; regulator-always-on; }; @@ -149,7 +149,7 @@ vccio_sd: REG5 { regulator-name = "VCCIO_SD"; - regulator-min-microvolt = <3300000>; + regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; -- cgit v1.2.3 From d59df5d1cdbddf098f934d68426731ecac0d11c8 Mon Sep 17 00:00:00 2001 From: Matthias Brugger Date: Fri, 11 Dec 2015 15:45:58 +0100 Subject: ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name The card detect pin is currently called sdmcc-cd. This patch fixes the typo and renames the pin to sdmmc-cd. Signed-off-by: Matthias Brugger Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 6d6cc16669b2..c4e085bba762 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -1157,7 +1157,7 @@ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up>; }; - sdmmc_cd: sdmcc-cd { + sdmmc_cd: sdmmc-cd { rockchip,pins = <6 22 RK_FUNC_1 &pcfg_pull_up>; }; -- cgit v1.2.3 From 618a43eaea14cb4f6526a4e93c6b791778d160b0 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 3 Dec 2015 15:33:56 +0900 Subject: ARM: dts: uniphier: change IRQ number of UART3 of PH1-Pro4 SoC The UART3 is assigned with IRQ 29 for old SoCs, IRQ 177 for new ones, and PH1-Pro4 is on the boundary. PH1-sLD3: UART3 is unavailable PH1-LD4, PH1-sLD8: only IRQ 29 is supported PH1-Pro4: both IRQ 29 and 177 are supported PH1-Pro5, ProXstream2, PH1-LD6b: only IRQ 177 is supported This SoC can choose either IRQ 29 or IRQ 177, but the former is shared with another hardware (low speed serial0). The latter is dedicated for this hardware and more recommended. Signed-off-by: Masahiro Yamada Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/uniphier-ph1-pro4.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi index 254642fe0e71..bbf37273bb73 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi @@ -151,7 +151,7 @@ reg = <0x54006b00 0x40>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 29 4>; + interrupts = <0 177 4>; clocks = <&uart_clk>; fifo-size = <64>; }; -- cgit v1.2.3 From 629b557ab4cd339bce759a1d87a56842df43b4a7 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 3 Dec 2015 15:33:57 +0900 Subject: ARM: dts: uniphier: factor out common nodes to uniphier-common32.dtsi UniPhier SoCs (except PH1-sLD3) have several nodes in common. Factor out them into uniphier-common32.dtsi. This improves the code maintainability. PH1-sLD3 is so old that it has more or less different register maps than the others. So, it cannot be included in this refactoring. Signed-off-by: Masahiro Yamada Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/uniphier-common32.dtsi | 135 +++++++++++++ arch/arm/boot/dts/uniphier-ph1-ld4.dtsi | 265 +++++++++---------------- arch/arm/boot/dts/uniphier-ph1-pro4.dtsi | 288 ++++++++++------------------ arch/arm/boot/dts/uniphier-ph1-pro5.dtsi | 274 +++++++++----------------- arch/arm/boot/dts/uniphier-ph1-sld8.dtsi | 266 +++++++++---------------- arch/arm/boot/dts/uniphier-proxstream2.dtsi | 269 +++++++++----------------- 6 files changed, 605 insertions(+), 892 deletions(-) create mode 100644 arch/arm/boot/dts/uniphier-common32.dtsi diff --git a/arch/arm/boot/dts/uniphier-common32.dtsi b/arch/arm/boot/dts/uniphier-common32.dtsi new file mode 100644 index 000000000000..ea9301aaa461 --- /dev/null +++ b/arch/arm/boot/dts/uniphier-common32.dtsi @@ -0,0 +1,135 @@ +/* + * Device Tree Source commonly used by UniPhier ARM SoCs + * + * Copyright (C) 2015 Masahiro Yamada + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/include/ "skeleton.dtsi" + +/ { + soc: soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + interrupt-parent = <&intc>; + + extbus: extbus { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + }; + + serial0: serial@54006800 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006800 0x40>; + interrupts = <0 33 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + clocks = <&uart_clk>; + }; + + serial1: serial@54006900 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006900 0x40>; + interrupts = <0 35 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + clocks = <&uart_clk>; + }; + + serial2: serial@54006a00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006a00 0x40>; + interrupts = <0 37 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + clocks = <&uart_clk>; + }; + + serial3: serial@54006b00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006b00 0x40>; + interrupts = <0 177 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + clocks = <&uart_clk>; + }; + + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; + }; + + timer@60000200 { + compatible = "arm,cortex-a9-global-timer"; + reg = <0x60000200 0x20>; + interrupts = <1 11 0x104>; + clocks = <&arm_timer_clk>; + }; + + timer@60000600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0x60000600 0x20>; + interrupts = <1 13 0x104>; + clocks = <&arm_timer_clk>; + }; + + intc: interrupt-controller@60001000 { + compatible = "arm,cortex-a9-gic"; + reg = <0x60001000 0x1000>, + <0x60000100 0x100>; + #interrupt-cells = <3>; + interrupt-controller; + }; + + pinctrl: pinctrl@5f801000 { + /* specify compatible in each SoC DTSI */ + reg = <0x5f801000 0xe00>; + }; + }; +}; + +/include/ "uniphier-pinctrl.dtsi" diff --git a/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi b/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi index af493819548d..34f0d8dcd814 100644 --- a/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi @@ -42,7 +42,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/include/ "skeleton.dtsi" +/include/ "uniphier-common32.dtsi" / { compatible = "socionext,ph1-ld4"; @@ -78,188 +78,105 @@ clock-frequency = <100000000>; }; }; +}; - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-parent = <&intc>; - - extbus: extbus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - }; - - l2: l2-cache@500c0000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, - <0x506c0000 0x400>; - interrupts = <0 174 4>, <0 175 4>; - cache-unified; - cache-size = <(512 * 1024)>; - cache-sets = <256>; - cache-line-size = <128>; - cache-level = <2>; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006800 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial1: serial@54006900 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006900 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - interrupts = <0 35 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial2: serial@54006a00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006a00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - interrupts = <0 37 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial3: serial@54006b00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006b00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 29 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - i2c0: i2c@58400000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58400000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0>; - interrupts = <0 41 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; - - i2c1: i2c@58480000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58480000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - interrupts = <0 42 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; - - /* chip-internal connection for DMD */ - i2c2: i2c@58500000 { - compatible = "socionext,uniphier-i2c"; - reg = <0x58500000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - interrupts = <0 43 1>; - clocks = <&iobus_clk>; - clock-frequency = <400000>; - }; +&soc { + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(512 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; - i2c3: i2c@58580000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58580000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - interrupts = <0 44 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; + i2c0: i2c@58400000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58400000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - system-bus-controller@58c00000 { - compatible = "socionext,uniphier-system-bus-controller"; - reg = <0x58c00000 0x400>, <0x59800000 0x2000>; - }; + i2c1: i2c@58480000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58480000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - usb0: usb@5a800100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a800100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb0>; - interrupts = <0 80 4>; - }; + /* chip-internal connection for DMD */ + i2c2: i2c@58500000 { + compatible = "socionext,uniphier-i2c"; + reg = <0x58500000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 43 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clocks = <&iobus_clk>; + clock-frequency = <400000>; + }; - usb1: usb@5a810100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a810100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb1>; - interrupts = <0 81 4>; - }; + i2c3: i2c@58580000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58580000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - usb2: usb@5a820100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a820100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb2>; - interrupts = <0 82 4>; - }; + usb0: usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a800100 0x100>; + interrupts = <0 80 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>; + }; - pinctrl: pinctrl@5f801000 { - compatible = "socionext,ph1-ld4-pinctrl", - "syscon"; - reg = <0x5f801000 0xe00>; - }; + usb1: usb@5a810100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a810100 0x100>; + interrupts = <0 81 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + }; - timer@60000200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x60000200 0x20>; - interrupts = <1 11 0x104>; - clocks = <&arm_timer_clk>; - }; + usb2: usb@5a820100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a820100 0x100>; + interrupts = <0 82 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; + }; - timer@60000600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x60000600 0x20>; - interrupts = <1 13 0x104>; - clocks = <&arm_timer_clk>; - }; +}; - intc: interrupt-controller@60001000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x60001000 0x1000>, - <0x60000100 0x100>; - }; - }; +&serial3 { + interrupts = <0 29 4>; }; -/include/ "uniphier-pinctrl.dtsi" +&pinctrl { + compatible = "socionext,ph1-ld4-pinctrl", "syscon"; +}; diff --git a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi index bbf37273bb73..d78142fb35c4 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi @@ -42,7 +42,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/include/ "skeleton.dtsi" +/include/ "uniphier-common32.dtsi" / { compatible = "socionext,ph1-pro4"; @@ -86,203 +86,115 @@ clock-frequency = <50000000>; }; }; +}; - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-parent = <&intc>; - - extbus: extbus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - }; - - l2: l2-cache@500c0000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, - <0x506c0000 0x400>; - interrupts = <0 174 4>, <0 175 4>; - cache-unified; - cache-size = <(768 * 1024)>; - cache-sets = <256>; - cache-line-size = <128>; - cache-level = <2>; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006800 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial1: serial@54006900 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006900 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - interrupts = <0 35 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial2: serial@54006a00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006a00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - interrupts = <0 37 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial3: serial@54006b00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006b00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 177 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - i2c0: i2c@58780000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58780000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0>; - interrupts = <0 41 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c1: i2c@58781000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58781000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - interrupts = <0 42 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c2: i2c@58782000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58782000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - interrupts = <0 43 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c3: i2c@58783000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58783000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - interrupts = <0 44 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - /* i2c4 does not exist */ +&soc { + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(768 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; - /* chip-internal connection for DMD */ - i2c5: i2c@58785000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58785000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 25 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - /* chip-internal connection for HDMI */ - i2c6: i2c@58786000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58786000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 26 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c1: i2c@58781000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58781000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - system-bus-controller@58c00000 { - compatible = "socionext,uniphier-system-bus-controller"; - reg = <0x58c00000 0x400>, <0x59800000 0x2000>; - }; + i2c2: i2c@58782000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58782000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 43 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - usb2: usb@5a800100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a800100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb2>; - interrupts = <0 80 4>; - }; + i2c3: i2c@58783000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58783000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - usb3: usb@5a810100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a810100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb3>; - interrupts = <0 81 4>; - }; + /* i2c4 does not exist */ - pinctrl: pinctrl@5f801000 { - compatible = "socionext,ph1-pro4-pinctrl", - "syscon"; - reg = <0x5f801000 0xe00>; - }; + /* chip-internal connection for DMD */ + i2c5: i2c@58785000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58785000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 25 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; + }; - timer@60000200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x60000200 0x20>; - interrupts = <1 11 0x304>; - clocks = <&arm_timer_clk>; - }; + /* chip-internal connection for HDMI */ + i2c6: i2c@58786000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58786000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 26 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; + }; - timer@60000600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x60000600 0x20>; - interrupts = <1 13 0x304>; - clocks = <&arm_timer_clk>; - }; + usb2: usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a800100 0x100>; + interrupts = <0 80 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; + }; - intc: interrupt-controller@60001000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x60001000 0x1000>, - <0x60000100 0x100>; - }; + usb3: usb@5a810100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a810100 0x100>; + interrupts = <0 81 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; }; }; -/include/ "uniphier-pinctrl.dtsi" +&pinctrl { + compatible = "socionext,ph1-pro4-pinctrl", "syscon"; +}; diff --git a/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi b/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi index 11eb76239feb..2f389ea75e01 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi @@ -42,7 +42,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/include/ "skeleton.dtsi" +/include/ "uniphier-common32.dtsi" / { compatible = "socionext,ph1-pro5"; @@ -86,193 +86,109 @@ clock-frequency = <50000000>; }; }; +}; - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-parent = <&intc>; - - extbus: extbus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - }; - - l2: l2-cache@500c0000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c0000 0x2000>, <0x503c0100 0x8>, - <0x506c0000 0x400>; - interrupts = <0 190 4>, <0 191 4>; - cache-unified; - cache-size = <(2 * 1024 * 1024)>; - cache-sets = <512>; - cache-line-size = <128>; - cache-level = <2>; - next-level-cache = <&l3>; - }; - - l3: l3-cache@500c8000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c8000 0x2000>, <0x503c8100 0x8>, - <0x506c8000 0x400>; - interrupts = <0 174 4>, <0 175 4>; - cache-unified; - cache-size = <(2 * 1024 * 1024)>; - cache-sets = <512>; - cache-line-size = <256>; - cache-level = <3>; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006800 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - }; - - serial1: serial@54006900 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006900 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - interrupts = <0 35 4>; - clocks = <&uart_clk>; - }; - - serial2: serial@54006a00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006a00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - interrupts = <0 37 4>; - clocks = <&uart_clk>; - }; - - serial3: serial@54006b00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006b00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 177 4>; - clocks = <&uart_clk>; - }; - - i2c0: i2c@58780000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58780000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0>; - interrupts = <0 41 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c1: i2c@58781000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58781000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - interrupts = <0 42 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c2: i2c@58782000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58782000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - interrupts = <0 43 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c3: i2c@58783000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58783000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - interrupts = <0 44 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; +&soc { + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x8>, <0x506c0000 0x400>; + interrupts = <0 190 4>, <0 191 4>; + cache-unified; + cache-size = <(2 * 1024 * 1024)>; + cache-sets = <512>; + cache-line-size = <128>; + cache-level = <2>; + next-level-cache = <&l3>; + }; - /* i2c4 does not exist */ + l3: l3-cache@500c8000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c8000 0x2000>, <0x503c8100 0x8>, <0x506c8000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(2 * 1024 * 1024)>; + cache-sets = <512>; + cache-line-size = <256>; + cache-level = <3>; + }; - /* chip-internal connection for DMD */ - i2c5: i2c@58785000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58785000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 25 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - /* chip-internal connection for HDMI */ - i2c6: i2c@58786000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58786000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 26 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c1: i2c@58781000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58781000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - system-bus-controller@58c00000 { - compatible = "socionext,uniphier-system-bus-controller"; - reg = <0x58c00000 0x400>, <0x59800000 0x2000>; - }; + i2c2: i2c@58782000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58782000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 43 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - pinctrl: pinctrl@5f801000 { - compatible = "socionext,ph1-pro5-pinctrl", "syscon"; - reg = <0x5f801000 0xe00>; - }; + i2c3: i2c@58783000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58783000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - timer@60000200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x60000200 0x20>; - interrupts = <1 11 0x304>; - clocks = <&arm_timer_clk>; - }; + /* i2c4 does not exist */ - timer@60000600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x60000600 0x20>; - interrupts = <1 13 0x304>; - clocks = <&arm_timer_clk>; - }; + /* chip-internal connection for DMD */ + i2c5: i2c@58785000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58785000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 25 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; + }; - intc: interrupt-controller@60001000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x60001000 0x1000>, - <0x60000100 0x100>; - }; + /* chip-internal connection for HDMI */ + i2c6: i2c@58786000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58786000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 26 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; }; }; -/include/ "uniphier-pinctrl.dtsi" +&pinctrl { + compatible = "socionext,ph1-pro5-pinctrl", "syscon"; +}; diff --git a/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi b/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi index e88559b66be7..7d06a1c487d8 100644 --- a/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi @@ -42,7 +42,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/include/ "skeleton.dtsi" +/include/ "uniphier-common32.dtsi" / { compatible = "socionext,ph1-sld8"; @@ -78,188 +78,104 @@ clock-frequency = <100000000>; }; }; +}; - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-parent = <&intc>; - - extbus: extbus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - }; - - l2: l2-cache@500c0000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, - <0x506c0000 0x400>; - interrupts = <0 174 4>, <0 175 4>; - cache-unified; - cache-size = <(256 * 1024)>; - cache-sets = <256>; - cache-line-size = <128>; - cache-level = <2>; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006800 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial1: serial@54006900 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006900 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - interrupts = <0 35 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial2: serial@54006a00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006a00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - interrupts = <0 37 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - serial3: serial@54006b00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006b00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 29 4>; - clocks = <&uart_clk>; - fifo-size = <64>; - }; - - i2c0: i2c@58400000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58400000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0>; - interrupts = <0 41 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; - - i2c1: i2c@58480000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58480000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - interrupts = <0 42 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; - - /* chip-internal connection for DMD */ - i2c2: i2c@58500000 { - compatible = "socionext,uniphier-i2c"; - reg = <0x58500000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - interrupts = <0 43 1>; - clocks = <&iobus_clk>; - clock-frequency = <400000>; - }; - - i2c3: i2c@58580000 { - compatible = "socionext,uniphier-i2c"; - status = "disabled"; - reg = <0x58580000 0x40>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - interrupts = <0 44 1>; - clocks = <&iobus_clk>; - clock-frequency = <100000>; - }; - - system-bus-controller@58c00000 { - compatible = "socionext,uniphier-system-bus-controller"; - reg = <0x58c00000 0x400>, <0x59800000 0x2000>; - }; +&soc { + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(256 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; - usb0: usb@5a800100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a800100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb0>; - interrupts = <0 80 4>; - }; + i2c0: i2c@58400000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58400000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - usb1: usb@5a810100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a810100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb1>; - interrupts = <0 81 4>; - }; + i2c1: i2c@58480000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58480000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - usb2: usb@5a820100 { - compatible = "socionext,uniphier-ehci", "generic-ehci"; - status = "disabled"; - reg = <0x5a820100 0x100>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb2>; - interrupts = <0 82 4>; - }; + /* chip-internal connection for DMD */ + i2c2: i2c@58500000 { + compatible = "socionext,uniphier-i2c"; + reg = <0x58500000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 43 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clocks = <&iobus_clk>; + clock-frequency = <400000>; + }; - pinctrl: pinctrl@5f801000 { - compatible = "socionext,ph1-sld8-pinctrl", - "syscon"; - reg = <0x5f801000 0xe00>; - }; + i2c3: i2c@58580000 { + compatible = "socionext,uniphier-i2c"; + status = "disabled"; + reg = <0x58580000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&iobus_clk>; + clock-frequency = <100000>; + }; - timer@60000200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x60000200 0x20>; - interrupts = <1 11 0x104>; - clocks = <&arm_timer_clk>; - }; + usb0: usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a800100 0x100>; + interrupts = <0 80 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>; + }; - timer@60000600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x60000600 0x20>; - interrupts = <1 13 0x104>; - clocks = <&arm_timer_clk>; - }; + usb1: usb@5a810100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a810100 0x100>; + interrupts = <0 81 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + }; - intc: interrupt-controller@60001000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x60001000 0x1000>, - <0x60000100 0x100>; - }; + usb2: usb@5a820100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a820100 0x100>; + interrupts = <0 82 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; }; }; -/include/ "uniphier-pinctrl.dtsi" +&serial3 { + interrupts = <0 29 4>; +}; + +&pinctrl { + compatible = "socionext,ph1-sld8-pinctrl", "syscon"; +}; diff --git a/arch/arm/boot/dts/uniphier-proxstream2.dtsi b/arch/arm/boot/dts/uniphier-proxstream2.dtsi index 259f1a909e24..6bd353f2d77e 100644 --- a/arch/arm/boot/dts/uniphier-proxstream2.dtsi +++ b/arch/arm/boot/dts/uniphier-proxstream2.dtsi @@ -42,7 +42,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/include/ "skeleton.dtsi" +/include/ "uniphier-common32.dtsi" / { compatible = "socionext,proxstream2"; @@ -100,189 +100,106 @@ clock-frequency = <50000000>; }; }; +}; - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-parent = <&intc>; - - extbus: extbus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - }; - - l2: l2-cache@500c0000 { - compatible = "socionext,uniphier-system-cache"; - reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, - <0x506c0000 0x400>; - interrupts = <0 174 4>, <0 175 4>, <0 190 4>, <0 191 4>; - cache-unified; - cache-size = <(1280 * 1024)>; - cache-sets = <512>; - cache-line-size = <128>; - cache-level = <2>; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006800 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - }; - - serial1: serial@54006900 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006900 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - interrupts = <0 35 4>; - clocks = <&uart_clk>; - }; - - serial2: serial@54006a00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006a00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - interrupts = <0 37 4>; - clocks = <&uart_clk>; - }; - - serial3: serial@54006b00 { - compatible = "socionext,uniphier-uart"; - status = "disabled"; - reg = <0x54006b00 0x40>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3>; - interrupts = <0 177 4>; - clocks = <&uart_clk>; - }; - - i2c0: i2c@58780000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58780000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0>; - interrupts = <0 41 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c1: i2c@58781000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58781000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - interrupts = <0 42 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c2: i2c@58782000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58782000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - interrupts = <0 43 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - i2c3: i2c@58783000 { - compatible = "socionext,uniphier-fi2c"; - status = "disabled"; - reg = <0x58783000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - interrupts = <0 44 4>; - clocks = <&i2c_clk>; - clock-frequency = <100000>; - }; - - /* chip-internal connection for DMD */ - i2c4: i2c@58784000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58784000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 45 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; +&soc { + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>, <0 190 4>, <0 191 4>; + cache-unified; + cache-size = <(1280 * 1024)>; + cache-sets = <512>; + cache-line-size = <128>; + cache-level = <2>; + }; - /* chip-internal connection for STM */ - i2c5: i2c@58785000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58785000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 25 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - /* chip-internal connection for HDMI */ - i2c6: i2c@58786000 { - compatible = "socionext,uniphier-fi2c"; - reg = <0x58786000 0x80>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 26 4>; - clocks = <&i2c_clk>; - clock-frequency = <400000>; - }; + i2c1: i2c@58781000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58781000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - system-bus-controller@58c00000 { - compatible = "socionext,uniphier-system-bus-controller"; - reg = <0x58c00000 0x400>, <0x59800000 0x2000>; - }; + i2c2: i2c@58782000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58782000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + interrupts = <0 43 4>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - pinctrl: pinctrl@5f801000 { - compatible = "socionext,proxstream2-pinctrl", "syscon"; - reg = <0x5f801000 0xe00>; - }; + i2c3: i2c@58783000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58783000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; - timer@60000200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x60000200 0x20>; - interrupts = <1 11 0xf04>; - clocks = <&arm_timer_clk>; - }; + /* chip-internal connection for DMD */ + i2c4: i2c@58784000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58784000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 45 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; + }; - timer@60000600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x60000600 0x20>; - interrupts = <1 13 0xf04>; - clocks = <&arm_timer_clk>; - }; + /* chip-internal connection for STM */ + i2c5: i2c@58785000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58785000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 25 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; + }; - intc: interrupt-controller@60001000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x60001000 0x1000>, - <0x60000100 0x100>; - }; + /* chip-internal connection for HDMI */ + i2c6: i2c@58786000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58786000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 26 4>; + clocks = <&i2c_clk>; + clock-frequency = <400000>; }; }; -/include/ "uniphier-pinctrl.dtsi" +&pinctrl { + compatible = "socionext,proxstream2-pinctrl", "syscon"; +}; -- cgit v1.2.3 From 9848ebeb952d2a46852bdde96101d280fc69b54b Mon Sep 17 00:00:00 2001 From: Jeffy Chen Date: Fri, 11 Dec 2015 09:30:51 +0800 Subject: ARM: dts: rockchip: add core rk3228 dtsi Initial release for rk3228 shared dtsi. Signed-off-by: Jeffy Chen Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3228.dtsi | 442 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 442 insertions(+) create mode 100644 arch/arm/boot/dts/rk3228.dtsi diff --git a/arch/arm/boot/dts/rk3228.dtsi b/arch/arm/boot/dts/rk3228.dtsi new file mode 100644 index 000000000000..119ff12ab440 --- /dev/null +++ b/arch/arm/boot/dts/rk3228.dtsi @@ -0,0 +1,442 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include +#include +#include +#include +#include +#include "skeleton.dtsi" + +/ { + compatible = "rockchip,rk3228"; + + interrupt-parent = <&gic>; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@f00 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf00>; + resets = <&cru SRST_CORE0>; + operating-points = < + /* KHz uV */ + 816000 1000000 + >; + clock-latency = <40000>; + clocks = <&cru ARMCLK>; + }; + + cpu1: cpu@f01 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf01>; + resets = <&cru SRST_CORE1>; + }; + + cpu2: cpu@f02 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf02>; + resets = <&cru SRST_CORE2>; + }; + + cpu3: cpu@f03 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf03>; + resets = <&cru SRST_CORE3>; + }; + }; + + amba { + compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pdma: pdma@110f0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x110f0000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + clocks = <&cru ACLK_DMAC>; + clock-names = "apb_pclk"; + }; + }; + + arm-pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts = , + , + , + ; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + timer { + compatible = "arm,armv7-timer"; + arm,cpu-registers-not-fw-configured; + interrupts = , + , + , + ; + clock-frequency = <24000000>; + }; + + xin24m: oscillator { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xin24m"; + #clock-cells = <0>; + }; + + grf: syscon@11000000 { + compatible = "syscon"; + reg = <0x11000000 0x1000>; + }; + + uart0: serial@11010000 { + compatible = "snps,dw-apb-uart"; + reg = <0x11010000 0x100>; + interrupts = ; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@11020000 { + compatible = "snps,dw-apb-uart"; + reg = <0x11020000 0x100>; + interrupts = ; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_xfer>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart2: serial@11030000 { + compatible = "snps,dw-apb-uart"; + reg = <0x11030000 0x100>; + interrupts = ; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + pwm0: pwm@110b0000 { + compatible = "rockchip,rk3288-pwm"; + reg = <0x110b0000 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + status = "disabled"; + }; + + pwm1: pwm@110b0010 { + compatible = "rockchip,rk3288-pwm"; + reg = <0x110b0010 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_pin>; + status = "disabled"; + }; + + pwm2: pwm@110b0020 { + compatible = "rockchip,rk3288-pwm"; + reg = <0x110b0020 0x10>; + #pwm-cells = <3>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pin>; + status = "disabled"; + }; + + pwm3: pwm@110b0030 { + compatible = "rockchip,rk3288-pwm"; + reg = <0x110b0030 0x10>; + #pwm-cells = <2>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pin>; + status = "disabled"; + }; + + timer: timer@110c0000 { + compatible = "rockchip,rk3288-timer"; + reg = <0x110c0000 0x20>; + interrupts = ; + clocks = <&xin24m>, <&cru PCLK_TIMER>; + clock-names = "timer", "pclk"; + }; + + cru: clock-controller@110e0000 { + compatible = "rockchip,rk3228-cru"; + reg = <0x110e0000 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = <&cru PLL_GPLL>; + assigned-clock-rates = <594000000>; + }; + + emmc: dwmmc@30020000 { + compatible = "rockchip,rk3288-dw-mshc"; + reg = <0x30020000 0x4000>; + interrupts = ; + clock-frequency = <37500000>; + clock-freq-min-max = <400000 37500000>; + clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, + <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; + bus-width = <8>; + default-sample-phase = <158>; + num-slots = <1>; + fifo-depth = <0x100>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; + status = "disabled"; + }; + + gic: interrupt-controller@32010000 { + compatible = "arm,gic-400"; + interrupt-controller; + #interrupt-cells = <3>; + #address-cells = <0>; + + reg = <0x32011000 0x1000>, + <0x32012000 0x1000>, + <0x32014000 0x2000>, + <0x32016000 0x2000>; + interrupts = ; + }; + + pinctrl: pinctrl { + compatible = "rockchip,rk3228-pinctrl"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@11110000 { + compatible = "rockchip,gpio-bank"; + reg = <0x11110000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO0>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio1@11120000 { + compatible = "rockchip,gpio-bank"; + reg = <0x11120000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio2@11130000 { + compatible = "rockchip,gpio-bank"; + reg = <0x11130000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO2>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio3@11140000 { + compatible = "rockchip,gpio-bank"; + reg = <0x11140000 0x100>; + interrupts = ; + clocks = <&cru PCLK_GPIO3>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + pcfg_pull_up: pcfg-pull-up { + bias-pull-up; + }; + + pcfg_pull_down: pcfg-pull-down { + bias-pull-down; + }; + + pcfg_pull_none: pcfg-pull-none { + bias-disable; + }; + + emmc { + emmc_clk: emmc-clk { + rockchip,pins = <2 7 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_cmd: emmc-cmd { + rockchip,pins = <1 22 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_bus8: emmc-bus8 { + rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>, + <1 25 RK_FUNC_2 &pcfg_pull_none>, + <1 26 RK_FUNC_2 &pcfg_pull_none>, + <1 27 RK_FUNC_2 &pcfg_pull_none>, + <1 28 RK_FUNC_2 &pcfg_pull_none>, + <1 29 RK_FUNC_2 &pcfg_pull_none>, + <1 30 RK_FUNC_2 &pcfg_pull_none>, + <1 31 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm0 { + pwm0_pin: pwm0-pin { + rockchip,pins = <3 21 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + pwm1 { + pwm1_pin: pwm1-pin { + rockchip,pins = <0 30 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm2 { + pwm2_pin: pwm2-pin { + rockchip,pins = <1 12 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm3 { + pwm3_pin: pwm3-pin { + rockchip,pins = <1 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + uart0 { + uart0_xfer: uart0-xfer { + rockchip,pins = <2 26 RK_FUNC_1 &pcfg_pull_none>, + <2 27 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_cts: uart0-cts { + rockchip,pins = <2 29 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_rts: uart0-rts { + rockchip,pins = <0 17 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart1 { + uart1_xfer: uart1-xfer { + rockchip,pins = <1 9 RK_FUNC_1 &pcfg_pull_none>, + <1 10 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart1_cts: uart1-cts { + rockchip,pins = <1 8 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart1_rts: uart1-rts { + rockchip,pins = <1 11 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>, + <1 19 RK_FUNC_2 &pcfg_pull_none>; + }; + + uart2_cts: uart2-cts { + rockchip,pins = <0 25 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart2_rts: uart2-rts { + rockchip,pins = <0 24 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + }; +}; -- cgit v1.2.3 From 67e044a510d0e00656ae2ab4f0ee30971a2f40e7 Mon Sep 17 00:00:00 2001 From: Jeffy Chen Date: Fri, 11 Dec 2015 09:30:52 +0800 Subject: ARM: dts: rockchip: add rk3228-evb board Initial release for rk3228 sdk board. Signed-off-by: Jeffy Chen Signed-off-by: Heiko Stuebner --- Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3228-evb.dts | 66 ++++++++++++++++++++++ 3 files changed, 71 insertions(+) create mode 100644 arch/arm/boot/dts/rk3228-evb.dts diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 2fa0a213a0c1..56a12defd87b 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -86,3 +86,7 @@ Rockchip platforms device tree bindings - Rockchip R88 board: Required root node properties: - compatible = "rockchip,r88", "rockchip,rk3368"; + +- Rockchip RK3228 Evaluation board: + Required root node properties: + - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8b49bfcbc5d4..37a74e9b667e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -517,6 +517,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-marsboard.dtb \ rk3066a-rayeager.dtb \ rk3188-radxarock.dtb \ + rk3228-evb.dtb \ rk3288-evb-act8846.dtb \ rk3288-evb-rk808.dtb \ rk3288-firefly-beta.dtb \ diff --git a/arch/arm/boot/dts/rk3228-evb.dts b/arch/arm/boot/dts/rk3228-evb.dts new file mode 100644 index 000000000000..e3898b810150 --- /dev/null +++ b/arch/arm/boot/dts/rk3228-evb.dts @@ -0,0 +1,66 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3228.dtsi" + +/ { + model = "Rockchip RK3228 Evaluation board"; + compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; + + memory { + device_type = "memory"; + reg = <0x60000000 0x40000000>; + }; +}; + +&emmc { + broken-cd; + cap-mmc-highspeed; + mmc-ddr-1_8v; + disable-wp; + non-removable; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; -- cgit v1.2.3 From 8818555964eed0010044c4d85f096452b14eb8b5 Mon Sep 17 00:00:00 2001 From: ZhengShunQian Date: Tue, 11 Aug 2015 18:13:44 +0800 Subject: ARM: dts: rockchip: add eFuse config of rk3288 SoC This patch add the eFuse dt config of rk3288 SoC. Signed-off-by: ZhengShunQian Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index c4e085bba762..6fb0e1764594 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -899,6 +899,19 @@ interrupts = ; }; + efuse: efuse@ffb40000 { + compatible = "rockchip,rockchip-efuse"; + reg = <0xffb40000 0x20>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE256>; + clock-names = "pclk_efuse"; + + cpu_leakage: cpu_leakage@17 { + reg = <0x17 0x1>; + }; + }; + usbphy: phy { compatible = "rockchip,rk3288-usb-phy"; rockchip,grf = <&grf>; -- cgit v1.2.3 From e57f6e5e19d415afd4054f58a7eacbfe96fc09e0 Mon Sep 17 00:00:00 2001 From: Soren Brinkmann Date: Fri, 23 Oct 2015 09:25:31 -0700 Subject: ARM: zynq: DT: Add interrupt-controller property to GPIO GPIO can be used as interrupt-controller. Add the missing properties to the GPIO node. Signed-off-by: Soren Brinkmann Reviewed-by: Moritz Fischer Acked-by: Linus Walleij Signed-off-by: Michal Simek --- arch/arm/boot/dts/zynq-7000.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi index 1a5220e05109..fe1a5d0cf03b 100644 --- a/arch/arm/boot/dts/zynq-7000.dtsi +++ b/arch/arm/boot/dts/zynq-7000.dtsi @@ -101,6 +101,8 @@ #gpio-cells = <2>; clocks = <&clkc 42>; gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; interrupt-parent = <&intc>; interrupts = <0 20 4>; reg = <0xe000a000 0x1000>; -- cgit v1.2.3 From b0d12e9a661546ad5810a2af820b5d9d46090a3b Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:16 +0100 Subject: ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek Cc: "Sören Brinkmann" Signed-off-by: Sudeep Holla Signed-off-by: Michal Simek --- arch/arm/boot/dts/zynq-zc702.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/zynq-zc702.dts index 5df8f81f4217..cb64209bca08 100644 --- a/arch/arm/boot/dts/zynq-zc702.dts +++ b/arch/arm/boot/dts/zynq-zc702.dts @@ -43,14 +43,14 @@ label = "sw14"; gpios = <&gpio0 12 0>; linux,code = <108>; /* down */ - gpio-key,wakeup; + wakeup-source; autorepeat; }; sw13 { label = "sw13"; gpios = <&gpio0 14 0>; linux,code = <103>; /* up */ - gpio-key,wakeup; + wakeup-source; autorepeat; }; }; -- cgit v1.2.3 From bc5ba9b98435bf76d92e0954da1784695aa449f1 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 5 Nov 2015 17:46:06 +0900 Subject: ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus The SLCR (System-Level Control Registers) block is an MFD (Multi Function Device) rather than a bus. "simple-mfd" seems a more suitable compatible string than "simple-bus". Signed-off-by: Masahiro Yamada Signed-off-by: Michal Simek --- arch/arm/boot/dts/zynq-7000.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi index fe1a5d0cf03b..59a35dfefa6c 100644 --- a/arch/arm/boot/dts/zynq-7000.dtsi +++ b/arch/arm/boot/dts/zynq-7000.dtsi @@ -240,7 +240,7 @@ slcr: slcr@f8000000 { #address-cells = <1>; #size-cells = <1>; - compatible = "xlnx,zynq-slcr", "syscon", "simple-bus"; + compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd"; reg = <0xF8000000 0x1000>; ranges; clkc: clkc@100 { -- cgit v1.2.3 From 400b6a0cbef55d1ae32808eaa1ef1c28820bf6ac Mon Sep 17 00:00:00 2001 From: Moritz Fischer Date: Mon, 9 Nov 2015 10:51:51 -0800 Subject: ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit By adding labels to the cpu nodes in the dtsi, a dts that includes it can change the OPPs by referencing the cpu0 through the label. Signed-off-by: Moritz Fischer Reviewed-by: Sören Brinkmann Signed-off-by: Michal Simek --- arch/arm/boot/dts/zynq-7000.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi index 59a35dfefa6c..f283ff08381c 100644 --- a/arch/arm/boot/dts/zynq-7000.dtsi +++ b/arch/arm/boot/dts/zynq-7000.dtsi @@ -19,7 +19,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <0>; @@ -33,7 +33,7 @@ >; }; - cpu@1 { + cpu1: cpu@1 { compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <1>; -- cgit v1.2.3 From d3369b1ebad02e81ecf02e2a4837b576d19b3b21 Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Wed, 11 Nov 2015 15:34:30 +0800 Subject: ARM: dts: rockchip: add eFuse node for rk3066a SoCs This patch add the eFuse dt node for rk3066a SoCs. Signed-off-by: Caesar Wang Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3066a.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rk3066a.dtsi index 1003f9c1ca8a..58bac5053858 100644 --- a/arch/arm/boot/dts/rk3066a.dtsi +++ b/arch/arm/boot/dts/rk3066a.dtsi @@ -159,6 +159,19 @@ clock-names = "timer", "pclk"; }; + efuse: efuse@20010000 { + compatible = "rockchip,rockchip-efuse"; + reg = <0x20010000 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE>; + clock-names = "pclk_efuse"; + + cpu_leakage: cpu_leakage { + reg = <0x17 0x1>; + }; + }; + timer@20038000 { compatible = "snps,dw-apb-timer-osc"; reg = <0x20038000 0x100>; -- cgit v1.2.3 From 4b0d98ae2d3dabdf63deb62874e631f7de6eb786 Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Wed, 11 Nov 2015 15:34:31 +0800 Subject: ARM: dts: rockchip: add eFuse node for rk3188 SoCs This patch add the eFuse dt node for rk3188 SoCs. Signed-off-by: Caesar Wang Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3188.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi index 42a67d8fe129..348d46b7ada5 100644 --- a/arch/arm/boot/dts/rk3188.dtsi +++ b/arch/arm/boot/dts/rk3188.dtsi @@ -146,6 +146,19 @@ #reset-cells = <1>; }; + efuse: efuse@20010000 { + compatible = "rockchip,rockchip-efuse"; + reg = <0x20010000 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE>; + clock-names = "pclk_efuse"; + + cpu_leakage: cpu_leakage { + reg = <0x17 0x1>; + }; + }; + usbphy: phy { compatible = "rockchip,rk3188-usb-phy", "rockchip,rk3288-usb-phy"; rockchip,grf = <&grf>; -- cgit v1.2.3 From 5c36aa6fda503b72a1b63e650abba62c46b96553 Mon Sep 17 00:00:00 2001 From: Ariel D'Alessandro Date: Tue, 17 Nov 2015 17:02:55 -0300 Subject: ARM: dts: lpc18xx: add EEPROM memory node Add node for the NXP LPC18xx EEPROM memory which can be found in NXP LPC185x/3x and LPC435x/3x/2x/1x devices. Signed-off-by: Ariel D'Alessandro Signed-off-by: Joachim Eastwood --- arch/arm/boot/dts/lpc18xx.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/lpc18xx.dtsi b/arch/arm/boot/dts/lpc18xx.dtsi index 52591d83e8cd..053a1f54f4bb 100644 --- a/arch/arm/boot/dts/lpc18xx.dtsi +++ b/arch/arm/boot/dts/lpc18xx.dtsi @@ -166,6 +166,17 @@ status = "disabled"; }; + eeprom: eeprom@4000e000 { + compatible = "nxp,lpc1857-eeprom"; + reg = <0x4000e000 0x1000>, <0x20040000 0x4000>; + reg-names = "reg", "mem"; + clocks = <&ccu1 CLK_CPU_EEPROM>; + clock-names = "eeprom"; + resets = <&rgu 27>; + interrupts = <4>; + status = "disabled"; + }; + mac: ethernet@40010000 { compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac"; reg = <0x40010000 0x2000>; -- cgit v1.2.3 From 7d775d34b181c1884827fac9f6d1dced83cbd344 Mon Sep 17 00:00:00 2001 From: Joachim Eastwood Date: Mon, 14 Dec 2015 23:03:50 +0100 Subject: ARM: dts: lpc4357: enable EEPROM memory Enable EEPROM for all LPC435x/3x/2x/1x controllers that include the 16 kB EEPROM device. Signed-off-by: Joachim Eastwood --- arch/arm/boot/dts/lpc4357.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/lpc4357.dtsi b/arch/arm/boot/dts/lpc4357.dtsi index fb9ecc754e8d..72f12db8d53a 100644 --- a/arch/arm/boot/dts/lpc4357.dtsi +++ b/arch/arm/boot/dts/lpc4357.dtsi @@ -37,3 +37,7 @@ }; }; }; + +&eeprom { + status = "okay"; +}; -- cgit v1.2.3 From a086dfe5bfd625cab32da405dfde877ab2f577a6 Mon Sep 17 00:00:00 2001 From: Joachim Eastwood Date: Sat, 24 Oct 2015 20:28:25 +0200 Subject: ARM: dts: lpc4357-ea4357: add mma7455 i2c accelerometer Add Freescale MMA7455 3-axis I2C accelerometer as found on Embedded Artists' LPC4357 Developer's Kit to the device tree. This makes it possible to access the accelerometer through the API provided by IIO. Signed-off-by: Joachim Eastwood --- arch/arm/boot/dts/lpc4357-ea4357-devkit.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts b/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts index 391121d24daa..079d3cf8c00b 100644 --- a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts +++ b/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts @@ -467,6 +467,11 @@ pinctrl-0 = <&i2c0_pins>; clock-frequency = <400000>; + mma7455@1d { + compatible = "fsl,mma7455"; + reg = <0x1d>; + }; + lm75@48 { compatible = "nxp,lm75"; reg = <0x48>; -- cgit v1.2.3 From 7888c8c12fb44ffc5bda08f0ae144b1cede8b4a3 Mon Sep 17 00:00:00 2001 From: Ariel D'Alessandro Date: Mon, 23 Nov 2015 09:37:04 -0300 Subject: ARM: dts: lpc4337-ciaa: enable SCT-PWM Enable the PWM based on the State Configurable Timer (SCT) included in the LPC4337 SoC of the CIAA-NXP board. Signed-off-by: Ariel D'Alessandro Signed-off-by: Joachim Eastwood --- arch/arm/boot/dts/lpc4337-ciaa.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/lpc4337-ciaa.dts b/arch/arm/boot/dts/lpc4337-ciaa.dts index 5f500c1ad89c..f126b713b175 100644 --- a/arch/arm/boot/dts/lpc4337-ciaa.dts +++ b/arch/arm/boot/dts/lpc4337-ciaa.dts @@ -166,6 +166,10 @@ pinctrl-0 = <&enet_rmii_pins>; }; +&sct_pwm { + status = "okay"; +}; + &ssp1 { status = "okay"; pinctrl-names = "default"; -- cgit v1.2.3 From 5743520806db4731cc30fad4cb2f01f0501a930c Mon Sep 17 00:00:00 2001 From: Ariel D'Alessandro Date: Mon, 23 Nov 2015 09:37:05 -0300 Subject: ARM: dts: lpc4337-ciaa: add i2c0 and devices Add I2C0 and two I2C EEPROM devices on the CIAA-NXP board: * 24AA1025 EEPROM, 1Mbit: it is accessed as two 512Kbit EEPROMs. * 24AA025E48 EEPROM, 2kbit. Signed-off-by: Ariel D'Alessandro Signed-off-by: Joachim Eastwood --- arch/arm/boot/dts/lpc4337-ciaa.dts | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/arch/arm/boot/dts/lpc4337-ciaa.dts b/arch/arm/boot/dts/lpc4337-ciaa.dts index f126b713b175..5cfadb06c8df 100644 --- a/arch/arm/boot/dts/lpc4337-ciaa.dts +++ b/arch/arm/boot/dts/lpc4337-ciaa.dts @@ -99,6 +99,14 @@ }; }; + i2c0_pins: i2c0-pins { + i2c0_pins_cfg { + pins = "i2c0_scl", "i2c0_sda"; + function = "i2c0"; + input-enable; + }; + }; + ssp_pins: ssp-pins { ssp1_cs { pins = "p6_7"; @@ -159,6 +167,28 @@ clock-frequency = <50000000>; }; +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + + eeprom@50 { + compatible = "microchip,24c512"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "microchip,24c02"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "microchip,24c512"; + reg = <0x54>; + }; +}; + &mac { status = "okay"; phy-mode = "rmii"; -- cgit v1.2.3 From ac8e7f31c70e3089a46afd449d84c8a957053eea Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 8 Dec 2015 10:37:50 +0100 Subject: ARM: shmobile: r8a7790: dtsi: add internal delay for i2c IPs Signed-off-by: Wolfram Sang Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 9f3036b80c0e..4eab5f43f7e5 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -417,6 +417,7 @@ interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C0>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; @@ -428,6 +429,7 @@ interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C1>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -439,6 +441,7 @@ interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C2>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -450,6 +453,7 @@ interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C3>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; -- cgit v1.2.3 From 49160dc19fcfa00c0d0901853aac49df87228915 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 8 Dec 2015 10:37:51 +0100 Subject: ARM: shmobile: r8a7791: dtsi: add internal delay for i2c IPs Signed-off-by: Wolfram Sang Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 36559cb0eb6b..3a2551094b8b 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -407,6 +407,7 @@ interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C0>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -418,6 +419,7 @@ interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C1>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -429,6 +431,7 @@ interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C2>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -440,6 +443,7 @@ interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C3>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -451,6 +455,7 @@ interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C4>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -463,6 +468,7 @@ interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C5>; power-domains = <&cpg_clocks>; + i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; -- cgit v1.2.3 From 691cd0a64d9215a838a7351de890d815b9a2622e Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 8 Dec 2015 10:37:52 +0100 Subject: ARM: shmobile: r8a7794: dtsi: add internal delay for i2c IPs Signed-off-by: Wolfram Sang Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 89e914f2a2cf..7fb2da2f54ff 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -518,6 +518,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -529,6 +530,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -540,6 +542,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -551,6 +554,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -562,6 +566,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -573,6 +578,7 @@ power-domains = <&cpg_clocks>; #address-cells = <1>; #size-cells = <0>; + i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; -- cgit v1.2.3 From d4eaf73b629fafda9c1a14fd72900dd0cfb610b3 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Wed, 7 Oct 2015 14:32:59 +0200 Subject: ARM: add DT bindings for the ARM11MPCore CPU cluster The ARM11MPCore has a Snoop Control Unit, but references to it were missing from the DT specification. Define a compatible string for this unit. Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/arm/scu.txt | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt index c447680519bb..08a587875996 100644 --- a/Documentation/devicetree/bindings/arm/scu.txt +++ b/Documentation/devicetree/bindings/arm/scu.txt @@ -10,10 +10,13 @@ References: Revision r2p0 - Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual Revision r0p1 +- ARM11 MPCore: see DDI0360F ARM 11 MPCore Processor Technical Reference + Manial Revision r2p0 - compatible : Should be: "arm,cortex-a9-scu" "arm,cortex-a5-scu" + "arm,arm11mp-scu" - reg : Specify the base address and the size of the SCU register window. -- cgit v1.2.3 From 1478cebfa0b472f797134d6a1d6d7e1222fd1a96 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 13 Oct 2015 14:27:30 +0200 Subject: clk: add ARM syscon ICST device tree bindings This adds the device tree bindings for the ARM Syscon ICST oscillators, which is a register-level interface to the Integrated Device Technology (IDT) ICS525 and ICS307 serially programmable oscillators. Cc: devicetree@vger.kernel.org Cc: Michael Turquette Cc: linux-clk@vger.kernel.org Acked-by: Stephen Boyd Acked-by: Rob Herring Signed-off-by: Linus Walleij --- .../devicetree/bindings/clock/arm-syscon-icst.txt | 40 ++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/arm-syscon-icst.txt diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt new file mode 100644 index 000000000000..8b7177cecb36 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -0,0 +1,40 @@ +ARM System Controller ICST clocks + +The ICS525 and ICS307 oscillators are produced by Integrated Devices +Technology (IDT). ARM integrated these oscillators deeply into their +reference designs by adding special control registers that manage such +oscillators to their system controllers. + +The ARM system controller contains logic to serialize and initialize +an ICST clock request after a write to the 32 bit register at an offset +into the system controller. Furthermore, to even be able to alter one of +these frequencies, the system controller must first be unlocked by +writing a special token to another offset in the system controller. + +The ICST oscillator must be provided inside a system controller node. + +Required properties: +- lock-offset: the offset address into the system controller where the + unlocking register is located +- vco-offset: the offset address into the system controller where the + ICST control register is located (even 32 bit address) +- compatible: must be one of "arm,syscon-icst525" or "arm,syscon-icst307" +- #clock-cells: must be <0> +- clocks: parent clock, since the ICST needs a parent clock to derive its + frequency from, this attribute is compulsory. + +Example: + +syscon: syscon@10000000 { + compatible = "syscon"; + reg = <0x10000000 0x1000>; + + oscclk0: osc0@0c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x0c>; + clocks = <&xtal24mhz>; + }; + (...) +}; -- cgit v1.2.3 From acde758b31f33d1599a07930b8c0ea082157cf70 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 8 Oct 2015 11:11:48 +0200 Subject: ARM: realview: add device tree for PB11MPCore This adds a device tree for the ARM RealView ARM11MPCore reference design. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/arm-realview-pb11mp.dts | 668 ++++++++++++++++++++++++++++++ 2 files changed, 670 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/arm-realview-pb11mp.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..e66743bb3bff 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -510,7 +510,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-msm8960-cdp.dtb \ qcom-msm8974-sony-xperia-honami.dtb dtb-$(CONFIG_ARCH_REALVIEW) += \ - arm-realview-pb1176.dtb + arm-realview-pb1176.dtb \ + arm-realview-pb11mp.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts new file mode 100644 index 000000000000..896bd21d320c --- /dev/null +++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts @@ -0,0 +1,668 @@ +/* + * Copyright 2015 Linaro Ltd + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +/dts-v1/; +#include +#include +#include "skeleton.dtsi" + +/ { + model = "ARM RealView PB11MPcore"; + compatible = "arm,realview-pb11mp"; + + chosen { }; + + aliases { + serial0 = &pb11mp_serial0; + serial1 = &pb11mp_serial1; + serial2 = &pb11mp_serial2; + serial3 = &pb11mp_serial3; + }; + + memory { + /* + * The PB11MPCore has 512 MiB memory @ 0x70000000 + * and the first 256 are also remapped @ 0x00000000 + */ + reg = <0x70000000 0x20000000>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "arm,realview-smp"; + + MP11_0: cpu@0 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + reg = <0>; + next-level-cache = <&L2>; + }; + + MP11_1: cpu@1 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + reg = <1>; + next-level-cache = <&L2>; + }; + + MP11_2: cpu@2 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + reg = <2>; + next-level-cache = <&L2>; + }; + + MP11_3: cpu@3 { + device_type = "cpu"; + compatible = "arm,arm11mpcore"; + reg = <3>; + next-level-cache = <&L2>; + }; + }; + + /* Primary TestChip GIC synthesized with the CPU */ + intc_tc11mp: interrupt-controller@1f000100 { + compatible = "arm,tc11mp-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0x1f001000 0x1000>, + <0x1f000100 0x100>; + }; + + L2: l2-cache { + compatible = "arm,l220-cache"; + reg = <0x1f002000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, + <0 30 IRQ_TYPE_LEVEL_HIGH>, + <0 31 IRQ_TYPE_LEVEL_HIGH>; + cache-unified; + cache-level = <2>; + }; + + scu@1f000000 { + compatible = "arm,arm11mp-scu"; + reg = <0x1f000000 0x100>; + }; + + timer@1f000600 { + compatible = "arm,arm11mp-twd-timer"; + reg = <0x1f000600 0x20>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <1 13 0xf04>; + }; + + watchdog@1f000620 { + compatible = "arm,arm11mp-twd-wdt"; + reg = <0x1f000620 0x20>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <1 14 0xf04>; + }; + + /* PMU with one IRQ line per core */ + pmu { + compatible = "arm,arm11mpcore-pmu"; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>, + <0 18 IRQ_TYPE_LEVEL_HIGH>, + <0 19 IRQ_TYPE_LEVEL_HIGH>, + <0 20 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&MP11_0>, <&MP11_1>, <&MP11_2>, <&MP11_3>; + }; + + /* The voltage to the MMC card is hardwired at 3.3V */ + vmmc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + veth: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "veth"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + xtal24mhz: xtal24mhz@24M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + refclk32khz: refclk32khz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + timclk: timclk@1M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <24>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + mclk: mclk@24M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + kmiclk: kmiclk@24M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + sspclk: sspclk@24M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + uartclk: uartclk@24M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + wdogclk: wdogclk@24M { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; + clocks = <&xtal24mhz>; + }; + + /* FIXME: this actually hangs off the PLL clocks */ + pclk: pclk@0 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; + + flash0@40000000 { + /* 2 * 32MiB NOR Flash memory */ + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0x40000000 0x04000000>; + bank-width = <4>; + }; + + flash1@44000000 { + // 2 * 32MiB NOR Flash memory + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0x44000000 0x04000000>; + bank-width = <4>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "arm,realview-pb11mp-soc", "simple-bus"; + regmap = <&pb11mp_syscon>; + ranges; + + pb11mp_syscon: syscon@10000000 { + compatible = "arm,realview-pb11mp-syscon", "syscon", "simple-mfd"; + reg = <0x10000000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "versatile:0"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + led@08.1 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x02>; + label = "versatile:1"; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + led@08.2 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x04>; + label = "versatile:2"; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + led@08.3 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x08>; + label = "versatile:3"; + linux,default-trigger = "cpu1"; + default-state = "off"; + }; + led@08.4 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x10>; + label = "versatile:4"; + linux,default-trigger = "cpu2"; + default-state = "off"; + }; + led@08.5 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x20>; + label = "versatile:5"; + linux,default-trigger = "cpu3"; + default-state = "off"; + }; + led@08.6 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x40>; + label = "versatile:6"; + default-state = "off"; + }; + led@08.7 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x80>; + label = "versatile:7"; + default-state = "off"; + }; + + oscclk0: osc0@0c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x0C>; + clocks = <&xtal24mhz>; + }; + oscclk1: osc1@10 { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x10>; + clocks = <&xtal24mhz>; + }; + oscclk2: osc2@14 { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x14>; + clocks = <&xtal24mhz>; + }; + oscclk3: osc3@18 { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x18>; + clocks = <&xtal24mhz>; + }; + oscclk4: osc4@1c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x1c>; + clocks = <&xtal24mhz>; + }; + oscclk5: osc5@d4 { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0xd4>; + clocks = <&xtal24mhz>; + }; + oscclk6: osc6@d8 { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0xd8>; + clocks = <&xtal24mhz>; + }; + }; + + sp810_syscon: sysctl@10001000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x10001000 0x1000>; + clocks = <&refclk32khz>, <&timclk>, <&xtal24mhz>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclk0", + "timerclk1", + "timerclk2", + "timerclk3"; + assigned-clocks = <&sp810_syscon 0>, + <&sp810_syscon 1>, + <&sp810_syscon 2>, + <&sp810_syscon 3>; + assigned-clock-parents = <&timclk>, + <&timclk>, + <&timclk>, + <&timclk>; + }; + + i2c0: i2c@10002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "arm,versatile-i2c"; + reg = <0x10002000 0x1000>; + + rtc@68 { + compatible = "dallas,ds1338"; + reg = <0x68>; + }; + }; + + aaci: aaci@10004000 { + compatible = "arm,pl041", "arm,primecell"; + reg = <0x10004000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pclk>; + clock-names = "apb_pclk"; + }; + + mci: mmcsd@10005000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x10005000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>, + <0 15 IRQ_TYPE_LEVEL_HIGH>; + /* Due to frequent FIFO overruns, use just 500 kHz */ + max-frequency = <500000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + clocks = <&mclk>, <&pclk>; + clock-names = "mclk", "apb_pclk"; + vmmc-supply = <&vmmc>; + cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; + }; + + kmi0: kmi@10006000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x10006000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&kmiclk>, <&pclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + kmi1: kmi@10007000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x10007000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&kmiclk>, <&pclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + pb11mp_serial0: serial@10009000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x10009000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uartclk>, <&pclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + pb11mp_serial1: serial@1000a000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x1000a000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uartclk>, <&pclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + pb11mp_serial2: serial@1000b000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x1000b000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uartclk>, <&pclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + pb11mp_serial3: serial@1000c000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x1000c000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uartclk>, <&pclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + ssp@1000d000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x1000d000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sspclk>, <&pclk>; + clock-names = "SSPCLK", "apb_pclk"; + }; + + watchdog@1000f000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x1000f000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&wdogclk>, <&pclk>; + clock-names = "wdogclk", "apb_pclk"; + status = "disabled"; + }; + + watchdog@10010000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x10010000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&wdogclk>, <&pclk>; + clock-names = "wdogclk", "apb_pclk"; + }; + + timer01: timer@10011000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x10011000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 1 IRQ_TYPE_LEVEL_HIGH>; + arm,sp804-has-irq = <1>; + clocks = <&sp810_syscon 0>, + <&sp810_syscon 1>, + <&pclk>; + clock-names = "timerclk0", + "timerclk1", + "apb_pclk"; + }; + + timer23: timer@10012000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x10012000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>; + arm,sp804-has-irq = <1>; + clocks = <&sp810_syscon 2>, + <&sp810_syscon 3>, + <&pclk>; + clock-names = "timerclk2", + "timerclk3", + "apb_pclk"; + }; + + gpio0: gpio@10013000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x10013000 0x1000>; + gpio-controller; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pclk>; + clock-names = "apb_pclk"; + }; + + gpio1: gpio@10014000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x10014000 0x1000>; + gpio-controller; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pclk>; + clock-names = "apb_pclk"; + }; + + gpio2: gpio@10015000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x10015000 0x1000>; + gpio-controller; + interrupt-parent = <&intc_pb11mp>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pclk>; + clock-names = "apb_pclk"; + }; + + rtc: rtc@10017000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x10017000 0x1000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pclk>; + clock-names = "apb_pclk"; + }; + + timer45: timer@10018000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x10018000 0x1000>; + clocks = <&timclk>, <&pclk>; + clock-names = "timer", "apb_pclk"; + status = "disabled"; + }; + + timer67: timer@10019000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x10019000 0x1000>; + clocks = <&timclk>, <&pclk>; + clock-names = "timer", "apb_pclk"; + status = "disabled"; + }; + + + clcd@10020000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x10020000 0x1000>; + interrupt-parent = <&intc_pb11mp>; + interrupt-names = "combined"; + interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&oscclk4>, <&pclk>; + clock-names = "clcdclk", "apb_pclk"; + max-memory-bandwidth = <130000000>; /* 16bpp @ 63.5MHz */ + + port { + clcd_pads: endpoint { + remote-endpoint = <&clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; + + panel { + compatible = "panel-dpi"; + + port { + clcd_panel: endpoint { + remote-endpoint = <&clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <63500127>; + hactive = <1024>; + hback-porch = <152>; + hfront-porch = <48>; + hsync-len = <104>; + vactive = <768>; + vback-porch = <23>; + vfront-porch = <3>; + vsync-len = <4>; + }; + }; + }; + + /* + * This GIC on the Platform Baseboard is cascaded off the + * TestChip GIC + */ + intc_pb11mp: interrupt-controller@1e000000 { + compatible = "arm,arm11mp-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0x1e001000 0x1000>, + <0x1e000000 0x100>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* SMSC 9118 ethernet with PHY and EEPROM */ + ethernet@4e000000 { + compatible = "smsc,lan9118", "smsc,lan9115"; + reg = <0x4e000000 0x10000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vdd33a-supply = <&veth>; + vddvario-supply = <&veth>; + }; + + usb@4f000000 { + compatible = "nxp,usb-isp1761"; + reg = <0x4f000000 0x20000>; + interrupt-parent = <&intc_tc11mp>; + interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; + port1-otg; + }; + }; +}; -- cgit v1.2.3 From c8d6686e41afa560e4d5fc2b3f62aa79be3fb6d1 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 17 Nov 2015 13:30:56 +0900 Subject: ARM: shmobile: r8a7790: IPMMU compat string SoC part number update Update IPMMU compat strings to include SoC part number. By specifying SoC part number in DT it becomes possible to implement SoC specific features in the IPMMU driver. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 4eab5f43f7e5..ee587cd823f5 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -1770,7 +1770,7 @@ }; ipmmu_sy0: mmu@e6280000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xe6280000 0 0x1000>; interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, <0 224 IRQ_TYPE_LEVEL_HIGH>; @@ -1779,7 +1779,7 @@ }; ipmmu_sy1: mmu@e6290000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xe6290000 0 0x1000>; interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1787,7 +1787,7 @@ }; ipmmu_ds: mmu@e6740000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xe6740000 0 0x1000>; interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, <0 199 IRQ_TYPE_LEVEL_HIGH>; @@ -1796,7 +1796,7 @@ }; ipmmu_mp: mmu@ec680000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xec680000 0 0x1000>; interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1804,7 +1804,7 @@ }; ipmmu_mx: mmu@fe951000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xfe951000 0 0x1000>; interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; @@ -1813,7 +1813,7 @@ }; ipmmu_rt: mmu@ffc80000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7790", "renesas,ipmmu-vmsa"; reg = <0 0xffc80000 0 0x1000>; interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; -- cgit v1.2.3 From 3c8ab0c88eff0a5cc61bc56a5929819f26da0b4a Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 17 Nov 2015 13:31:05 +0900 Subject: ARM: shmobile: r8a7791: IPMMU compat string SoC part number update Update IPMMU compat strings to include SoC part number. By specifying SoC part number in DT it becomes possible to implement SoC specific features in the IPMMU driver. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791.dtsi | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 3a2551094b8b..3f15aa7dc4d6 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1590,7 +1590,7 @@ }; ipmmu_sy0: mmu@e6280000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xe6280000 0 0x1000>; interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, <0 224 IRQ_TYPE_LEVEL_HIGH>; @@ -1599,7 +1599,7 @@ }; ipmmu_sy1: mmu@e6290000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xe6290000 0 0x1000>; interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1607,7 +1607,7 @@ }; ipmmu_ds: mmu@e6740000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xe6740000 0 0x1000>; interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, <0 199 IRQ_TYPE_LEVEL_HIGH>; @@ -1616,7 +1616,7 @@ }; ipmmu_mp: mmu@ec680000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xec680000 0 0x1000>; interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1624,7 +1624,7 @@ }; ipmmu_mx: mmu@fe951000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xfe951000 0 0x1000>; interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; @@ -1633,7 +1633,7 @@ }; ipmmu_rt: mmu@ffc80000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xffc80000 0 0x1000>; interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1641,7 +1641,7 @@ }; ipmmu_gp: mmu@e62a0000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7791", "renesas,ipmmu-vmsa"; reg = <0 0xe62a0000 0 0x1000>; interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, <0 261 IRQ_TYPE_LEVEL_HIGH>; -- cgit v1.2.3 From c51b1473edf88d40b65f6ce95e35465484d2eb48 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 17 Nov 2015 13:31:13 +0900 Subject: ARM: shmobile: r8a7793: IPMMU compat string SoC part number update Update IPMMU compat strings to include SoC part number. By specifying SoC part number in DT it becomes possible to implement SoC specific features in the IPMMU driver. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793.dtsi | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index df607a92b2ed..aef9e69d6c26 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -847,7 +847,7 @@ }; ipmmu_sy0: mmu@e6280000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xe6280000 0 0x1000>; interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, <0 224 IRQ_TYPE_LEVEL_HIGH>; @@ -856,7 +856,7 @@ }; ipmmu_sy1: mmu@e6290000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xe6290000 0 0x1000>; interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -864,7 +864,7 @@ }; ipmmu_ds: mmu@e6740000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xe6740000 0 0x1000>; interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, <0 199 IRQ_TYPE_LEVEL_HIGH>; @@ -873,7 +873,7 @@ }; ipmmu_mp: mmu@ec680000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xec680000 0 0x1000>; interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -881,7 +881,7 @@ }; ipmmu_mx: mmu@fe951000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xfe951000 0 0x1000>; interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; @@ -890,7 +890,7 @@ }; ipmmu_rt: mmu@ffc80000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xffc80000 0 0x1000>; interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -898,7 +898,7 @@ }; ipmmu_gp: mmu@e62a0000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa"; reg = <0 0xe62a0000 0 0x1000>; interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, <0 261 IRQ_TYPE_LEVEL_HIGH>; -- cgit v1.2.3 From 0da4cfd1a22acd521d385bc80ef48f4d038d0a03 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 17 Nov 2015 13:31:22 +0900 Subject: ARM: shmobile: r8a7794: IPMMU compat string SoC part number update Update IPMMU compat strings to include SoC part number. By specifying SoC part number in DT it becomes possible to implement SoC specific features in the IPMMU driver. Signed-off-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 7fb2da2f54ff..6c78f1fae90f 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -1109,7 +1109,7 @@ }; ipmmu_sy0: mmu@e6280000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xe6280000 0 0x1000>; interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, <0 224 IRQ_TYPE_LEVEL_HIGH>; @@ -1118,7 +1118,7 @@ }; ipmmu_sy1: mmu@e6290000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xe6290000 0 0x1000>; interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1126,7 +1126,7 @@ }; ipmmu_ds: mmu@e6740000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xe6740000 0 0x1000>; interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, <0 199 IRQ_TYPE_LEVEL_HIGH>; @@ -1135,7 +1135,7 @@ }; ipmmu_mp: mmu@ec680000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xec680000 0 0x1000>; interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; #iommu-cells = <1>; @@ -1143,7 +1143,7 @@ }; ipmmu_mx: mmu@fe951000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xfe951000 0 0x1000>; interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; @@ -1152,7 +1152,7 @@ }; ipmmu_gp: mmu@e62a0000 { - compatible = "renesas,ipmmu-vmsa"; + compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa"; reg = <0 0xe62a0000 0 0x1000>; interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, <0 261 IRQ_TYPE_LEVEL_HIGH>; -- cgit v1.2.3 From 5e4458fa5d3890455c16fc28b2c082f4f15a19eb Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Wed, 4 Nov 2015 23:14:22 +0100 Subject: ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page 1119, section 37.6.1, Table 37-3 . Signed-off-by: Marek Vasut Cc: Alexandre Belloni Reviewed-by: Josh Wu Reported-by: Nicolas Ferre Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/sama5d4.dtsi | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index 2193637b9cd2..c61de23fd6af 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -1669,15 +1669,15 @@ pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 { atmel,pins = ; }; pinctrl_mmc0_dat1_3: mmc0_dat1_3 { atmel,pins = - ; }; }; -- cgit v1.2.3 From 49f6697499d4c3a635bea05fb96d4a2278e6ae8c Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 5 Nov 2015 03:25:01 +0100 Subject: ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus Add pinmux for the 4 remaining signals used in 8-bit MMC 0 bus configuration. Signed-off-by: Marek Vasut Cc: Alexandre Belloni Reviewed-by: Josh Wu Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/sama5d4.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index c61de23fd6af..47eaa220de25 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -1680,6 +1680,14 @@ AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA3, conflict with NAND_D4 */ >; }; + pinctrl_mmc0_dat4_7: mmc0_dat4_7 { + atmel,pins = + ; + }; }; mmc1 { -- cgit v1.2.3 From ca5a4b56220539ff2389a88ee7170bb4d6be2c24 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Wed, 4 Nov 2015 23:14:24 +0100 Subject: ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port, LEDs and expansion headers. Signed-off-by: Marek Vasut Cc: Alexandre Belloni Cc: Josh Wu Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi | 127 +++++++++++++++++++++ arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts | 170 ++++++++++++++++++++++++++++ 3 files changed, 298 insertions(+) create mode 100644 arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi create mode 100644 arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..0e965358304b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d34ek.dtb \ sama5d35ek.dtb \ sama5d36ek.dtb \ + at91-sama5d4_ma5d4evk.dtb \ at91-sama5d4_xplained.dtb \ at91-sama5d4ek.dtb dtb-$(CONFIG_ARCH_ATLAS6) += \ diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi new file mode 100644 index 000000000000..e7b2109fc85a --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi @@ -0,0 +1,127 @@ +/* + * Copyright (C) 2015 Marek Vasut + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "sama5d4.dtsi" + +/ { + model = "DENX MA5D4"; + compatible = "denx,ma5d4", "atmel,sama5d4", "atmel,sama5"; + + memory { + reg = <0x20000000 0x10000000>; + }; + + clocks { + main_clock: main_clock { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + + clk20m: clk20m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <20000000>; + clock-output-names = "clk20m"; + }; + }; + + ahb { + apb { + mmc0: mmc@f8000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7>; + vmmc-supply = <&vcc_mmc0_reg>; + vqmmc-supply = <&vcc_3v3_reg>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <8>; + broken-cd; + }; + }; + + spi0: spi@f8010000 { + cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; + status = "okay"; + + m25p80@0 { + compatible = "atmel,at25df321a"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; + + i2c0: i2c@f8014000 { + status = "okay"; + }; + + spi1: spi@fc018000 { + cs-gpios = <&pioB 22 0>, <&pioB 23 0>, <0>, <0>; + status = "okay"; + + can0: can@0 { + compatible = "microchip,mcp2515"; + reg = <0>; + clocks = <&clk20m>; + interrupt-parent = <&pioE>; + interrupts = <6 GPIO_ACTIVE_LOW>; + spi-max-frequency = <10000000>; + }; + + can1: can@1 { + compatible = "microchip,mcp2515"; + reg = <1>; + clocks = <&clk20m>; + interrupt-parent = <&pioE>; + interrupts = <7 GPIO_ACTIVE_LOW>; + spi-max-frequency = <10000000>; + }; + }; + + adc0: adc@fc034000 { + pinctrl-names = "default"; + pinctrl-0 = < + /* external trigger conflicts with USBA_VBUS */ + &pinctrl_adc0_ad0 + &pinctrl_adc0_ad1 + &pinctrl_adc0_ad2 + &pinctrl_adc0_ad3 + &pinctrl_adc0_ad4 + >; + atmel,adc-vref = <3300>; + status = "okay"; + }; + + watchdog@fc068640 { + status = "okay"; + }; + }; + }; + + vcc_3v3_reg: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "VCC 3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vcc_mmc0_reg: fixedregulator@1 { + compatible = "regulator-fixed"; + gpio = <&pioE 15 GPIO_ACTIVE_HIGH>; + regulator-name = "RST_n MCI0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_reg>; + regulator-boot-on; + }; +}; diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts b/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts new file mode 100644 index 000000000000..abaaba58fbec --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts @@ -0,0 +1,170 @@ +/* + * Copyright (C) 2015 Marek Vasut + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "at91-sama5d4_ma5d4.dtsi" + +/ { + model = "DENX MA5D4EVK"; + compatible = "denx,ma5d4evk", "atmel,sama5d4", "atmel,sama5"; + + chosen { + stdout-path = "serial3:115200n8"; + }; + + ahb { + usb0: gadget@00400000 { + atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; + }; + + usb1: ohci@00500000 { + num-ports = <3>; + atmel,vbus-gpio = <0 + &pioE 11 GPIO_ACTIVE_LOW + &pioE 14 GPIO_ACTIVE_LOW + >; + status = "okay"; + }; + + usb2: ehci@00600000 { + status = "okay"; + }; + + apb { + hlcdc: hlcdc@f0000000 { + status = "okay"; + + hlcdc-display-controller { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + + port@0 { + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + }; + + macb0: ethernet@f8020000 { + phy-mode = "rmii"; + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + + usart0: serial@f802c000 { + status = "okay"; + }; + + usart1: serial@f8030000 { + status = "okay"; + }; + + mmc1: mmc@fc000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; + vmmc-supply = <&vcc_mmc1_reg>; + vqmmc-supply = <&vcc_3v3_reg>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 5 0>; + }; + }; + + adc0: adc@fc034000 { + atmel,adc-ts-wires = <4>; + atmel,adc-ts-pressure-threshold = <10000>; + }; + + + pinctrl@fc06a000 { + board { + pinctrl_mmc1_cd: mmc1_cd { + atmel,pins = ; + }; + pinctrl_usba_vbus: usba_vbus { + atmel,pins = + ; + }; + }; + }; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&hlcdc_pwm 0 50000 0>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + user1 { + label = "user1"; + gpios = <&pioD 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + user2 { + label = "user2"; + gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + user3 { + label = "user3"; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + panel: panel { + /* Actually Ampire 800480R2 */ + compatible = "foxlink,fl500wvr00-a0t", "simple-panel"; + backlight = <&backlight>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint@0 { + reg = <0>; + remote-endpoint = <&hlcdc_panel_output>; + }; + }; + }; + + vcc_mmc1_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + gpio = <&pioE 17 GPIO_ACTIVE_LOW>; + regulator-name = "VDD MCI1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_reg>; + }; +}; -- cgit v1.2.3 From 92bd7aa413c00dd2ec1ba7f829a245f48e1e2ed3 Mon Sep 17 00:00:00 2001 From: Wenyou Yang Date: Thu, 5 Nov 2015 15:39:30 +0800 Subject: ARM: at91/dt: sama5d2: add watchdog node Add watchdog node to support SAMA5D4 watchdog. Signed-off-by: Wenyou Yang Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 4 ++++ arch/arm/boot/dts/sama5d2.dtsi | 7 +++++++ 2 files changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index ad6de73ed5a5..89a69f37fff2 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -206,6 +206,10 @@ }; }; + watchdog@f8048040 { + status = "okay"; + }; + uart3: serial@fc008000 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3_default>; diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi index 4dfca8fc49b3..545264b856b3 100644 --- a/arch/arm/boot/dts/sama5d2.dtsi +++ b/arch/arm/boot/dts/sama5d2.dtsi @@ -929,6 +929,13 @@ clocks = <&h32ck>; }; + watchdog@f8048040 { + compatible = "atmel,sama5d4-wdt"; + reg = <0xf8048040 0x10>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>; + status = "disabled"; + }; + sckc@f8048050 { compatible = "atmel,at91sam9x5-sckc"; reg = <0xf8048050 0x4>; -- cgit v1.2.3 From bdf9a4d3037fede143fc4b732debc77e9376dc58 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 1 Dec 2015 14:42:37 +0100 Subject: ARM: at91/dt: sama5d4 master clock can run at 200MHz now After the change of frequency a SAMA5D4 can reach, we have to modify the maximum clock specification for the master clock, up to 200MHz now. It avoids the wrong message saying that "master clk is overclocked" for this configuration. Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/sama5d4.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index 47eaa220de25..8ad54318a111 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -451,7 +451,7 @@ interrupt-parent = <&pmc>; interrupts = ; clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>; - atmel,clk-output-range = <125000000 177000000>; + atmel,clk-output-range = <125000000 200000000>; atmel,clk-divisors = <1 2 4 3>; }; -- cgit v1.2.3 From a2ebbb07959c37894fba2b9ec139b8bffdbd736c Mon Sep 17 00:00:00 2001 From: Ludovic Desroches Date: Thu, 3 Dec 2015 10:53:53 +0100 Subject: ARM: at91/dt: sama5d4: update i2c compatible string A new compatible string has been introduced: atmel,sama5d4-i2c. It allows to use the i2c-sda-hold-time-ns property if needed. Signed-off-by: Ludovic Desroches Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/sama5d4.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index 8ad54318a111..b8032bca4621 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -916,7 +916,7 @@ }; i2c0: i2c@f8014000 { - compatible = "atmel,at91sam9x5-i2c"; + compatible = "atmel,sama5d4-i2c"; reg = <0xf8014000 0x4000>; interrupts = <32 IRQ_TYPE_LEVEL_HIGH 6>; dmas = <&dma1 @@ -935,7 +935,7 @@ }; i2c1: i2c@f8018000 { - compatible = "atmel,at91sam9x5-i2c"; + compatible = "atmel,sama5d4-i2c"; reg = <0xf8018000 0x4000>; interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>; dmas = <&dma1 @@ -975,7 +975,7 @@ }; i2c2: i2c@f8024000 { - compatible = "atmel,at91sam9x5-i2c"; + compatible = "atmel,sama5d4-i2c"; reg = <0xf8024000 0x4000>; interrupts = <34 IRQ_TYPE_LEVEL_HIGH 6>; dmas = <&dma1 -- cgit v1.2.3 From 0a804b5729bb0021e63662b772db0f52de653056 Mon Sep 17 00:00:00 2001 From: Ludovic Desroches Date: Thu, 3 Dec 2015 10:53:54 +0100 Subject: ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time Data have to be held longer for the PMIC device. The ACT8945A datasheet claims that minimum SDA data hold time is about 300 ns. Signed-off-by: Ludovic Desroches Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 89a69f37fff2..80fdab72f4fa 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -129,6 +129,7 @@ dmas = <0>, <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c0_default>; + i2c-sda-hold-time-ns = <350>; status = "okay"; pmic: act8865@5b { -- cgit v1.2.3 From 61521e3924a1c4e45f7c9d061f496b55b8210088 Mon Sep 17 00:00:00 2001 From: Hans Ulli Kroll Date: Thu, 10 Dec 2015 06:33:08 +0100 Subject: ARM: dts: kirkwood: Add DTS for Zyxel NSA325 Add a new DTS file to support the Zyxel NSA325(v2) dual bay NAS device, based on the NSA320 DTS files. The only difference to the NSA320 device is GPIO47. This en/disables the power for the hdd in slot2, currently fixed to on. [gregory.clement@free-electrons.com: fix comment format] Signed-off-by: Hans Ulli Kroll Acked-by: Andrew Lunn Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-nsa325.dts | 238 ++++++++++++++++++++++++++++++++++ 2 files changed, 239 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-nsa325.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7e6a0532c656..2f56a3b3bf28 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -200,6 +200,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-ns2mini.dtb \ kirkwood-nsa310.dtb \ kirkwood-nsa310a.dtb \ + kirkwood-nsa325.dtb \ kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a7.dtb \ kirkwood-openrd-base.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/kirkwood-nsa325.dts new file mode 100644 index 000000000000..bc4ec9332387 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-nsa325.dts @@ -0,0 +1,238 @@ +/* Device tree file for the Zyxel NSA 325 NAS box. + * + * Copyright (c) 2015, Hans Ulli Kroll + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Based upon the board setup file created by Peter Schildmann + */ + +/dts-v1/; + +#include "kirkwood-nsa3x0-common.dtsi" + +/ { + model = "ZyXEL NSA325"; + compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_led_hdd2_green: pmx-led-hdd2-green { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_led_hdd2_red: pmx-led-hdd2-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_mcu_data: pmx-mcu-data { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_mcu_clk: pmx-mcu-clk { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_mcu_act: pmx-mcu-act { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_orange: pmx-led-sys-orange { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_green: pmx-led-hdd1-green { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_red: pmx-led-hdd1-red { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + pmx_htp: pmx-htp { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + /* + * Buzzer needs to be switched at around 1kHz so is + * not compatible with the gpio-beeper driver. + */ + pmx_buzzer: pmx-buzzer { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_vid_b1: pmx-vid-b1 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_power_resume_data: pmx-power-resume-data { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_power_resume_clk: pmx-power-resume-clk { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + + pmx_pwr_sata1: pmx-pwr-sata1 { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; + + /* This board uses the pcf8563 RTC instead of the SoC RTC */ + rtc@10300 { + status = "disabled"; + }; + + i2c@11000 { + status = "okay"; + + pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_pwr_sata1>; + pinctrl-names = "default"; + + usb0_power: regulator@1 { + enable-active-high; + }; + + sata1_power: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA1 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red + &pmx_led_usb_green + &pmx_led_sys_green &pmx_led_sys_orange + &pmx_led_copy_green &pmx_led_copy_red + &pmx_led_hdd1_green &pmx_led_hdd1_red>; + pinctrl-names = "default"; + + green-sys { + label = "nsa325:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; + orange-sys { + label = "nsa325:orange:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd1 { + label = "nsa325:green:hdd1"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + red-hdd1 { + label = "nsa325:red:hdd1"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + green-hdd2 { + label = "nsa325:green:hdd2"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + red-hdd2 { + label = "nsa325:red:hdd2"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + green-usb { + label = "nsa325:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + green-copy { + label = "nsa325:green:copy"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + red-copy { + label = "nsa325:red:copy"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + + /* The following pins are currently not assigned to a driver, + some of them should be configured as inputs. + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act + &pmx_htp &pmx_vid_b1 + &pmx_power_resume_data &pmx_power_resume_clk>; */ + }; + + +}; + +&mdio { + status = "okay"; + ethphy0: ethernet-phy@1 { + reg = <1>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + -- cgit v1.2.3 From 994a5814eb7e6cac316546989b9f69d10626dfd2 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 27 Nov 2015 00:00:54 +0100 Subject: ARM: mvebu: add kirkwood compatibles for cloudengine boards This adds the compatible strings for Cloudengine PogoPlug E02 and series 4. The former already has a devicetree in the kernel. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij Acked-by: Rob Herring Signed-off-by: Gregory CLEMENT --- Documentation/devicetree/bindings/arm/marvell,kirkwood.txt | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt index 5171ad8f48ff..ab0c9cdf388e 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -24,6 +24,8 @@ board. Currently known boards are: "buffalo,lswxl" "buffalo,lsxhl" "buffalo,lsxl" +"cloudengines,pogo02" +"cloudengines,pogoplugv4" "dlink,dns-320" "dlink,dns-320-a1" "dlink,dns-325" -- cgit v1.2.3 From b6e30a4705dbb7d0212eba1ff780a072f20ecca1 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 14 Dec 2015 15:32:55 +0100 Subject: ARM: mvebu: kirkwood: add PogoPlug series 4 device tree This adds a device tree for the CloudEngines PogoPlug series 4 NAS device. Inspired by out-of-tree boardfiles from ArchLinux by Kevin Mihelich. Cc: Moonman Cc: Kevin Mihelich Signed-off-by: Linus Walleij Acked-by: Andrew Lunn Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 2f56a3b3bf28..c0485b21ba25 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -207,6 +207,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-openrd-client.dtb \ kirkwood-openrd-ultimate.dtb \ kirkwood-pogo_e02.dtb \ + kirkwood-pogoplug-series-4.dtb \ kirkwood-rd88f6192.dtb \ kirkwood-rd88f6281-z0.dtb \ kirkwood-rd88f6281-a.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts new file mode 100644 index 000000000000..1db6f2c506cc --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts @@ -0,0 +1,178 @@ +/* + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4 + * inspired by the board files made by Kevin Mihelich for ArchLinux, + * and their DTS file. + * + * Copyright (C) 2015 Linus Walleij + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6192.dtsi" +#include + +/ { + model = "Cloud Engines PogoPlug Series 4"; + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; + }; + + chosen { + stdout-path = "uart0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_button_eject>; + pinctrl-names = "default"; + + button@1 { + debounce_interval = <50>; + wakeup-source; + linux,code = ; + label = "Eject Button"; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_led_green &pmx_led_red>; + pinctrl-names = "default"; + + health { + label = "pogoplugv4:green:health"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + fault { + label = "pogoplugv4:red:fault"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pinctrl { + pmx_sata0: pmx-sata0 { + marvell,pins = "mpp21"; + marvell,function = "sata0"; + }; + + pmx_sata1: pmx-sata1 { + marvell,pins = "mpp20"; + marvell,function = "sata1"; + }; + + pmx_sdio_cd: pmx-sdio-cd { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_sdio_wp: pmx-sdio-wp { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_button_eject: pmx-button-eject { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_green: pmx-led-green { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_led_red: pmx-led-red { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* + * This PCIE controller has a USB 3.0 XHCI controller at 1,0 + */ +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&sata { + status = "okay"; + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + nr-ports = <1>; +}; + +&sdio { + status = "okay"; + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>; + pinctrl-names = "default"; + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; +}; + +&nand { + /* 128 MiB of NAND flash */ + chip-delay = <40>; + status = "okay"; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x200000>; + read-only; + }; + + partition@200000 { + label = "uImage"; + reg = <0x00200000 0x300000>; + }; + + partition@500000 { + label = "uImage2"; + reg = <0x00500000 0x300000>; + }; + + partition@800000 { + label = "failsafe"; + reg = <0x00800000 0x800000>; + }; + + partition@1000000 { + label = "root"; + reg = <0x01000000 0x7000000>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; -- cgit v1.2.3 From 6c72d8ab263a3f2f28ec3360cca60bfec9bf2a5c Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 15 Dec 2015 17:38:02 +0100 Subject: ARM: dts: dove: add DT GPU support Add DT support for the Vivante GC600 GPU on Marvell Dove platforms. These nodes default to being disabled unless a platform decides they should be enabled. Signed-off-by: Russell King Signed-off-by: Lucas Stach Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/dove.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 9e109aab92d0..698d58cea20d 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -33,6 +33,12 @@ marvell,tauros2-cache-features = <0>; }; + gpu-subsystem { + compatible = "marvell,dove-gpu-subsystem"; + cores = <&gpu>; + status = "disabled"; + }; + i2c-mux { compatible = "i2c-mux-pinctrl"; #address-cells = <1>; @@ -782,6 +788,16 @@ #address-cells = <1>; #size-cells = <1>; }; + + gpu: gpu@840000 { + clocks = <÷r_clk 1>; + clock-names = "core"; + compatible = "vivante,gc"; + interrupts = <48>; + power-domains = <&gpu_domain>; + reg = <0x840000 0x4000>; + status = "disabled"; + }; }; }; }; -- cgit v1.2.3 From ce9981bd633213ff7c5938b1a374561b5a687d46 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 15 Dec 2015 17:38:03 +0100 Subject: ARM: dts: enable GPU for SolidRun's Cubox Enable the GPU for SolidRun's Cubox. Signed-off-by: Russell King Signed-off-by: Lucas Stach Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/dove-cubox.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts index e6fa251e17b9..af3cb633135f 100644 --- a/arch/arm/boot/dts/dove-cubox.dts +++ b/arch/arm/boot/dts/dove-cubox.dts @@ -62,6 +62,10 @@ pinctrl-0 = <&pmx_gpio_19>; pinctrl-names = "default"; }; + + gpu-subsystem { + status = "okay"; + }; }; &uart0 { status = "okay"; }; @@ -74,6 +78,10 @@ reg = <1>; }; +&gpu { + status = "okay"; +}; + &i2c0 { status = "okay"; clock-frequency = <100000>; -- cgit v1.2.3 From 8b44f5be20fd531054e546b662f46e619bff2e72 Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:14 +0100 Subject: ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property Though the driver will continue to check for and support the legacy "isil,irq2-can-wakeup-machine" boolean property to wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "isil,irq2-can-wakeup-machine" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Jason Cooper Cc: Andrew Lunn Cc: Gregory Clement Cc: Sebastian Hesselbarth Signed-off-by: Sudeep Holla Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-370-netgear-rn102.dts | 2 +- arch/arm/boot/dts/armada-370-netgear-rn104.dts | 2 +- arch/arm/boot/dts/armada-xp-netgear-rn2120.dts | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts index 5555875f44f9..39181b3fa90d 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts @@ -127,7 +127,7 @@ isl12057: isl12057@68 { compatible = "isil,isl12057"; reg = <0x68>; - isil,irq2-can-wakeup-machine; + wakeup-source; }; g762: g762@3e { diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts index 78b563c02f3c..faa474874cb8 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -133,7 +133,7 @@ isl12057: isl12057@68 { compatible = "isil,isl12057"; reg = <0x68>; - isil,irq2-can-wakeup-machine; + wakeup-source; }; g762: g762@3e { diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts index 6fe8972de0a2..62175a8848bc 100644 --- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts +++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts @@ -141,7 +141,7 @@ isl12057: isl12057@68 { compatible = "isil,isl12057"; reg = <0x68>; - isil,irq2-can-wakeup-machine; + wakeup-source; }; }; -- cgit v1.2.3 From aa2691279eaf50ff7983890c38491fbee73d1025 Mon Sep 17 00:00:00 2001 From: Georgi Djakov Date: Thu, 3 Dec 2015 16:02:55 +0200 Subject: arm: dts: qcom: apq8064: Add fixed rate on-board oscillators Currently the rates of the xo and sleep clocks are hard-coded in the GCC driver, but this is a board layout description that actually should be in the DT. Moving them into DT also allows us to insert the RPM controlled clocks between the DT and GCC clocks. Signed-off-by: Georgi Djakov Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index e6c7476036a4..edfc6ee56ea1 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -91,6 +91,26 @@ interrupts = <1 10 0x304>; }; + clocks { + cxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + pxo_board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + + sleep_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + sfpb_mutex: hwmutex { compatible = "qcom,sfpb-mutex"; syscon = <&sfpb_wrapper_mutex 0x604 0x4>; -- cgit v1.2.3 From 426ac151ec6b7eabd248a78351ecda4d6b188d34 Mon Sep 17 00:00:00 2001 From: "Ivan T. Ivanov" Date: Fri, 11 Dec 2015 18:29:58 +0000 Subject: ARM: dts: qcom: apq8064-ifc6410 Use hardware flow control for GSBI6 GSBI6 UART module is connected to BT chip, which uses hardware flow control lines. Enable them on SoC side. Signed-off-by: Ivan T. Ivanov Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index f40e93f09673..aa9303b84d67 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -164,7 +164,7 @@ gsbi@16500000 { status = "ok"; - qcom,mode = ; + qcom,mode = ; serial@16540000 { status = "ok"; -- cgit v1.2.3 From 64ab88638af03b361d1446ef3682ab176ff8726b Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 24 Sep 2015 14:18:56 -0500 Subject: arm: dts: Add APQ8084 SMEM nodes This patch adds all the required nodes to support SMEM on APQ8084 Signed-off-by: Andy Gross Acked-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-apq8084.dtsi | 36 ++++++++++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index fcffecae3e67..3d3b394a57a1 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -10,6 +10,17 @@ compatible = "qcom,apq8084"; interrupt-parent = <&intc>; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smem_mem: smem_region@fa00000 { + reg = <0xfa00000 0x200000>; + no-map; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -89,6 +100,15 @@ clock-frequency = <19200000>; }; + smem { + compatible = "qcom,smem"; + + qcom,rpm-msg-ram = <&rpm_msg_ram>; + memory-region = <&smem_mem>; + + hwlocks = <&tcsr_mutex 3>; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; @@ -225,6 +245,22 @@ reg = <0xfc400000 0x4000>; }; + tcsr_mutex_regs: syscon@fd484000 { + compatible = "syscon"; + reg = <0xfd484000 0x2000>; + }; + + tcsr_mutex: hwlock { + compatible = "qcom,tcsr-mutex"; + syscon = <&tcsr_mutex_regs 0 0x80>; + #hwlock-cells = <1>; + }; + + rpm_msg_ram: memory@fc428000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0xfc428000 0x4000>; + }; + tlmm: pinctrl@fd510000 { compatible = "qcom,apq8084-pinctrl"; reg = <0xfd510000 0x4000>; -- cgit v1.2.3 From 53ced99d70c4228be0465303625a1511db89323f Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 24 Sep 2015 14:18:57 -0500 Subject: arm: dts: Add RPM/SMD support on APQ8084 This patch adds support for RPM and SMD nodes that are present on APQ8084 platforms. Signed-off-by: Andy Gross Acked-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-apq8084.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index 3d3b394a57a1..29cb7e5749ab 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -123,6 +123,11 @@ <0xf9002000 0x1000>; }; + apcs: syscon@f9011000 { + compatible = "syscon"; + reg = <0xf9011000 0x1000>; + }; + timer@f9020000 { #address-cells = <1>; #size-cells = <1>; @@ -318,4 +323,19 @@ #interrupt-cells = <4>; }; }; + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-apq8084"; + qcom,smd-channels = "rpm_requests"; + }; + }; + }; }; -- cgit v1.2.3 From 4add1074576758fb23b7369ea62de09dac16561e Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 24 Sep 2015 14:18:58 -0500 Subject: arm: dts: Add support for PMA8084 on APQ8084 This patch adds support for the PMA8084 regulators found on APQ8084 platforms. Signed-off-by: Andy Gross Acked-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-apq8084.dtsi | 52 +++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index 29cb7e5749ab..08214cbae16d 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -335,6 +335,58 @@ rpm_requests { compatible = "qcom,rpm-apq8084"; qcom,smd-channels = "rpm_requests"; + + pma8084-regulators { + compatible = "qcom,rpm-pma8084-regulators"; + + pma8084_s1: s1 {}; + pma8084_s2: s2 {}; + pma8084_s3: s3 {}; + pma8084_s4: s4 {}; + pma8084_s5: s5 {}; + pma8084_s6: s6 {}; + pma8084_s7: s7 {}; + pma8084_s8: s8 {}; + pma8084_s9: s9 {}; + pma8084_s10: s10 {}; + pma8084_s11: s11 {}; + pma8084_s12: s12 {}; + + pma8084_l1: l1 {}; + pma8084_l2: l2 {}; + pma8084_l3: l3 {}; + pma8084_l4: l4 {}; + pma8084_l5: l5 {}; + pma8084_l6: l6 {}; + pma8084_l7: l7 {}; + pma8084_l8: l8 {}; + pma8084_l9: l9 {}; + pma8084_l10: l10 {}; + pma8084_l11: l11 {}; + pma8084_l12: l12 {}; + pma8084_l13: l13 {}; + pma8084_l14: l14 {}; + pma8084_l15: l15 {}; + pma8084_l16: l16 {}; + pma8084_l17: l17 {}; + pma8084_l18: l18 {}; + pma8084_l19: l19 {}; + pma8084_l20: l20 {}; + pma8084_l21: l21 {}; + pma8084_l22: l22 {}; + pma8084_l23: l23 {}; + pma8084_l24: l24 {}; + pma8084_l25: l25 {}; + pma8084_l26: l26 {}; + pma8084_l27: l27 {}; + + pma8084_lvs1: lvs1 {}; + pma8084_lvs2: lvs2 {}; + pma8084_lvs3: lvs3 {}; + pma8084_lvs4: lvs4 {}; + + pma8084_5vs1: 5vs1 {}; + }; }; }; }; -- cgit v1.2.3 From d01c8bec91414f2110370dfcb9dd33fc0e573cee Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 11 Dec 2015 11:59:38 +0900 Subject: ARM: shmobile: r8a779x: use SoC-specific usb-dmac compatibility strings Use recently SoC-specific compatibility strings in r8a779[01] device trees. Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790.dtsi | 4 ++-- arch/arm/boot/dts/r8a7791.dtsi | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index ee587cd823f5..7dfd393bfc7e 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -386,7 +386,7 @@ }; usb_dmac0: dma-controller@e65a0000 { - compatible = "renesas,usb-dmac"; + compatible = "renesas,r8a7790-usb-dmac", "renesas,usb-dmac"; reg = <0 0xe65a0000 0 0x100>; interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH 0 109 IRQ_TYPE_LEVEL_HIGH>; @@ -398,7 +398,7 @@ }; usb_dmac1: dma-controller@e65b0000 { - compatible = "renesas,usb-dmac"; + compatible = "renesas,r8a7790-usb-dmac", "renesas,usb-dmac"; reg = <0 0xe65b0000 0 0x100>; interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH 0 110 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 3f15aa7dc4d6..2a369ddcb6fd 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -375,7 +375,7 @@ }; usb_dmac0: dma-controller@e65a0000 { - compatible = "renesas,usb-dmac"; + compatible = "renesas,r8a7791-usb-dmac", "renesas,usb-dmac"; reg = <0 0xe65a0000 0 0x100>; interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH 0 109 IRQ_TYPE_LEVEL_HIGH>; @@ -387,7 +387,7 @@ }; usb_dmac1: dma-controller@e65b0000 { - compatible = "renesas,usb-dmac"; + compatible = "renesas,r8a7791-usb-dmac", "renesas,usb-dmac"; reg = <0 0xe65b0000 0 0x100>; interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH 0 110 IRQ_TYPE_LEVEL_HIGH>; -- cgit v1.2.3 From b5e5090660742c838ddc0b5d1a001e6fe3d5bfd5 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:33:36 +0200 Subject: ARM: DTS: am33xx: Use the new DT bindings for the eDMA3 Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and enable the DMA even crossbar with ti,am335x-edma-crossbar. With the new bindings boards can customize and tweak the DMA channel priority to match their needs. With the new binding the memcpy is safe to be used since with the old binding it was not possible for a driver to know which channel is allowed to be used as non HW triggered channel. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-evm.dts | 9 +--- arch/arm/boot/dts/am335x-pepper.dts | 11 +---- arch/arm/boot/dts/am33xx.dtsi | 94 ++++++++++++++++++++++++++----------- 3 files changed, 71 insertions(+), 43 deletions(-) diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index 4caf074063fe..a55072fb6646 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -743,8 +743,8 @@ &mmc3 { /* these are on the crossbar and are outlined in the xbar-event-map element */ - dmas = <&edma 12 - &edma 13>; + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; dma-names = "tx", "rx"; status = "okay"; vmmc-supply = <&wlan_en_reg>; @@ -766,11 +766,6 @@ }; }; -&edma { - ti,edma-xbar-event-map = /bits/ 16 <1 12 - 2 13>; -}; - &sham { status = "okay"; }; diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts index 9cb77a120319..4dd4f71498e5 100644 --- a/arch/arm/boot/dts/am335x-pepper.dts +++ b/arch/arm/boot/dts/am335x-pepper.dts @@ -339,13 +339,6 @@ ti,non-removable; }; -&edma { - /* Map eDMA MMC2 Events from Crossbar */ - ti,edma-xbar-event-map = /bits/ 16 <1 12 - 2 13>; -}; - - &mmc3 { /* Wifi & Bluetooth on MMC #3 */ status = "okay"; @@ -354,8 +347,8 @@ vmmmc-supply = <&v3v3c_reg>; bus-width = <4>; ti,non-removable; - dmas = <&edma 12 - &edma 13>; + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; dma-names = "tx", "rx"; }; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 9b8861891bf0..04885f9f959e 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -161,6 +161,14 @@ mboxes = <&mailbox &mbox_wkupm3>; }; + edma_xbar: dma-router@f90 { + compatible = "ti,am335x-edma-crossbar"; + reg = <0xf90 0x40>; + #dma-cells = <3>; + dma-requests = <32>; + dma-masters = <&edma>; + }; + scm_clockdomains: clockdomains { }; }; @@ -174,12 +182,44 @@ }; edma: edma@49000000 { - compatible = "ti,edma3"; - ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; - reg = <0x49000000 0x10000>, - <0x44e10f90 0x40>; + compatible = "ti,edma3-tpcc"; + ti,hwmods = "tpcc"; + reg = <0x49000000 0x10000>; + reg-names = "edma3_cc"; interrupts = <12 13 14>; - #dma-cells = <1>; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, + <&edma_tptc2 0>; + + ti,edma-memcpy-channels = <20 21>; + }; + + edma_tptc0: tptc@49800000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc0"; + reg = <0x49800000 0x100000>; + interrupts = <112>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc1: tptc@49900000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc1"; + reg = <0x49900000 0x100000>; + interrupts = <113>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc2: tptc@49a00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc2"; + reg = <0x49a00000 0x100000>; + interrupts = <114>; + interrupt-names = "edma3_tcerrint"; }; gpio0: gpio@44e07000 { @@ -233,7 +273,7 @@ reg = <0x44e09000 0x2000>; interrupts = <72>; status = "disabled"; - dmas = <&edma 26>, <&edma 27>; + dmas = <&edma 26 0>, <&edma 27 0>; dma-names = "tx", "rx"; }; @@ -244,7 +284,7 @@ reg = <0x48022000 0x2000>; interrupts = <73>; status = "disabled"; - dmas = <&edma 28>, <&edma 29>; + dmas = <&edma 28 0>, <&edma 29 0>; dma-names = "tx", "rx"; }; @@ -255,7 +295,7 @@ reg = <0x48024000 0x2000>; interrupts = <74>; status = "disabled"; - dmas = <&edma 30>, <&edma 31>; + dmas = <&edma 30 0>, <&edma 31 0>; dma-names = "tx", "rx"; }; @@ -322,8 +362,8 @@ ti,dual-volt; ti,needs-special-reset; ti,needs-special-hs-handling; - dmas = <&edma 24 - &edma 25>; + dmas = <&edma_xbar 24 0 0 + &edma_xbar 25 0 0>; dma-names = "tx", "rx"; interrupts = <64>; interrupt-parent = <&intc>; @@ -335,8 +375,8 @@ compatible = "ti,omap4-hsmmc"; ti,hwmods = "mmc2"; ti,needs-special-reset; - dmas = <&edma 2 - &edma 3>; + dmas = <&edma 2 0 + &edma 3 0>; dma-names = "tx", "rx"; interrupts = <28>; interrupt-parent = <&intc>; @@ -474,10 +514,10 @@ interrupts = <65>; ti,spi-num-cs = <2>; ti,hwmods = "spi0"; - dmas = <&edma 16 - &edma 17 - &edma 18 - &edma 19>; + dmas = <&edma 16 0 + &edma 17 0 + &edma 18 0 + &edma 19 0>; dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -490,10 +530,10 @@ interrupts = <125>; ti,spi-num-cs = <2>; ti,hwmods = "spi1"; - dmas = <&edma 42 - &edma 43 - &edma 44 - &edma 45>; + dmas = <&edma 42 0 + &edma 43 0 + &edma 44 0 + &edma 45 0>; dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -833,7 +873,7 @@ ti,hwmods = "sham"; reg = <0x53100000 0x200>; interrupts = <109>; - dmas = <&edma 36>; + dmas = <&edma 36 0>; dma-names = "rx"; }; @@ -842,8 +882,8 @@ ti,hwmods = "aes"; reg = <0x53500000 0xa0>; interrupts = <103>; - dmas = <&edma 6>, - <&edma 5>; + dmas = <&edma 6 0>, + <&edma 5 0>; dma-names = "tx", "rx"; }; @@ -856,8 +896,8 @@ interrupts = <80>, <81>; interrupt-names = "tx", "rx"; status = "disabled"; - dmas = <&edma 8>, - <&edma 9>; + dmas = <&edma 8 2>, + <&edma 9 2>; dma-names = "tx", "rx"; }; @@ -870,8 +910,8 @@ interrupts = <82>, <83>; interrupt-names = "tx", "rx"; status = "disabled"; - dmas = <&edma 10>, - <&edma 11>; + dmas = <&edma 10 2>, + <&edma 11 2>; dma-names = "tx", "rx"; }; -- cgit v1.2.3 From cce1ee000187c1584bf644406926aaffa1b2bc36 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:33:37 +0200 Subject: ARM: DTS: am437x: Use the new DT bindings for the eDMA3 Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and enable the DMA even crossbar with ti,am335x-edma-crossbar. With the new bindings boards can customize and tweak the DMA channel priority to match their needs. With the new binding the memcpy is safe to be used since with the old binding it was not possible for a driver to know which channel is allowed to be used as non HW triggered channel. Signed-off-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am4372.dtsi | 80 +++++++++++++++++++++++++++---------- arch/arm/boot/dts/am437x-gp-evm.dts | 9 +---- 2 files changed, 62 insertions(+), 27 deletions(-) diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index fda655c252f5..a2c9b7da0d9c 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -172,6 +172,14 @@ mboxes = <&mailbox &mbox_wkupm3>; }; + edma_xbar: dma-router@f90 { + compatible = "ti,am335x-edma-crossbar"; + reg = <0xf90 0x40>; + #dma-cells = <3>; + dma-requests = <64>; + dma-masters = <&edma>; + }; + scm_clockdomains: clockdomains { }; }; @@ -184,14 +192,46 @@ }; edma: edma@49000000 { - compatible = "ti,edma3"; - ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; - reg = <0x49000000 0x10000>, - <0x44e10f90 0x10>; + compatible = "ti,edma3-tpcc"; + ti,hwmods = "tpcc"; + reg = <0x49000000 0x10000>; + reg-names = "edma3_cc"; interrupts = , - , - ; - #dma-cells = <1>; + , + ; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, + <&edma_tptc2 0>; + + ti,edma-memcpy-channels = <32 33>; + }; + + edma_tptc0: tptc@49800000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc0"; + reg = <0x49800000 0x100000>; + interrupts = ; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc1: tptc@49900000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc1"; + reg = <0x49900000 0x100000>; + interrupts = ; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc2: tptc@49a00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc2"; + reg = <0x49a00000 0x100000>; + interrupts = ; + interrupt-names = "edma3_tcerrint"; }; uart0: serial@44e09000 { @@ -496,8 +536,8 @@ ti,hwmods = "mmc1"; ti,dual-volt; ti,needs-special-reset; - dmas = <&edma 24 - &edma 25>; + dmas = <&edma 24 0>, + <&edma 25 0>; dma-names = "tx", "rx"; interrupts = ; status = "disabled"; @@ -508,8 +548,8 @@ reg = <0x481d8000 0x1000>; ti,hwmods = "mmc2"; ti,needs-special-reset; - dmas = <&edma 2 - &edma 3>; + dmas = <&edma 2 0>, + <&edma 3 0>; dma-names = "tx", "rx"; interrupts = ; status = "disabled"; @@ -777,7 +817,7 @@ compatible = "ti,omap5-sham"; ti,hwmods = "sham"; reg = <0x53100000 0x300>; - dmas = <&edma 36>; + dmas = <&edma 36 0>; dma-names = "rx"; interrupts = ; }; @@ -787,8 +827,8 @@ ti,hwmods = "aes"; reg = <0x53501000 0xa0>; interrupts = ; - dmas = <&edma 6 - &edma 5>; + dmas = <&edma 6 0>, + <&edma 5 0>; dma-names = "tx", "rx"; }; @@ -797,8 +837,8 @@ ti,hwmods = "des"; reg = <0x53701000 0xa0>; interrupts = ; - dmas = <&edma 34 - &edma 33>; + dmas = <&edma 34 0>, + <&edma 33 0>; dma-names = "tx", "rx"; }; @@ -811,8 +851,8 @@ interrupts = <80>, <81>; interrupt-names = "tx", "rx"; status = "disabled"; - dmas = <&edma 8>, - <&edma 9>; + dmas = <&edma 8 2>, + <&edma 9 2>; dma-names = "tx", "rx"; }; @@ -825,8 +865,8 @@ interrupts = <82>, <83>; interrupt-names = "tx", "rx"; status = "disabled"; - dmas = <&edma 10>, - <&edma 11>; + dmas = <&edma 10 2>, + <&edma 11 2>; dma-names = "tx", "rx"; }; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 7f00e85eebed..64d43325bcbc 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -734,8 +734,8 @@ status = "okay"; /* these are on the crossbar and are outlined in the xbar-event-map element */ - dmas = <&edma 30 - &edma 31>; + dmas = <&edma_xbar 30 0 1>, + <&edma_xbar 31 0 2>; dma-names = "tx", "rx"; vmmc-supply = <&vmmcwl_fixed>; bus-width = <4>; @@ -756,11 +756,6 @@ }; }; -&edma { - ti,edma-xbar-event-map = /bits/ 16 <1 30 - 2 31>; -}; - &uart3 { status = "okay"; pinctrl-names = "default"; -- cgit v1.2.3 From 3efda00129bdf8a09e640ba7d08f8c7f48f32db1 Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:06 +0100 Subject: ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: "Benoît Cousson" Cc: Tony Lindgren Cc: linux-omap@vger.kernel.org Signed-off-by: Sudeep Holla Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-evm.dts | 4 ++-- arch/arm/boot/dts/am335x-evmsk.dts | 2 +- arch/arm/boot/dts/am335x-pepper.dts | 6 +++--- 3 files changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index a55072fb6646..0d6a68ce434a 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -83,14 +83,14 @@ label = "volume-up"; linux,code = <115>; gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; - gpio-key,wakeup; + wakeup-source; }; switch@10 { label = "volume-down"; linux,code = <114>; gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 9609668919f1..282fe1b37095 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -123,7 +123,7 @@ label = "button2"; linux,code = <0x102>; gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; - gpio-key,wakeup; + wakeup-source; }; switch@4 { diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts index 4dd4f71498e5..471a3a70ea1f 100644 --- a/arch/arm/boot/dts/am335x-pepper.dts +++ b/arch/arm/boot/dts/am335x-pepper.dts @@ -630,21 +630,21 @@ label = "home"; linux,code = ; gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; - gpio-key,wakeup; + wakeup-source; }; button@1 { label = "menu"; linux,code = ; gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; - gpio-key,wakeup; + wakeup-source; }; buttons@2 { label = "power"; linux,code = ; gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; - gpio-key,wakeup; + wakeup-source; }; }; -- cgit v1.2.3 From 0c4d63b323c8d39181f231596d98811ba32037b7 Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Wed, 21 Oct 2015 11:10:12 +0100 Subject: ARM: dts: omap: replace legacy *,wakeup property with wakeup-source MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Though the keyboard and other driver will continue to support the legacy "gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup source, "wakeup-source" is the new standard binding. This patch replaces all the legacy wakeup properties with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: "Benoît Cousson" Cc: Tony Lindgren Cc: linux-omap@vger.kernel.org Signed-off-by: Sudeep Holla Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 8 ++--- arch/arm/boot/dts/omap3-beagle-xm.dts | 2 +- arch/arm/boot/dts/omap3-beagle.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3x.dtsi | 2 +- arch/arm/boot/dts/omap3-devkit8000-common.dtsi | 2 +- arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi | 2 +- arch/arm/boot/dts/omap3-gta04.dtsi | 2 +- arch/arm/boot/dts/omap3-ldp.dts | 18 ++++++------ arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 2 +- arch/arm/boot/dts/omap3-n900.dts | 10 +++---- arch/arm/boot/dts/omap3-overo-alto35-common.dtsi | 2 +- .../boot/dts/omap3-overo-chestnut43-common.dtsi | 4 +-- arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi | 2 +- arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi | 2 +- arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi | 4 +-- arch/arm/boot/dts/omap3-overo-palo35-common.dtsi | 4 +-- arch/arm/boot/dts/omap3-overo-palo43-common.dtsi | 4 +-- arch/arm/boot/dts/omap3-pandora-common.dtsi | 34 +++++++++++----------- .../boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 2 +- arch/arm/boot/dts/omap4-duovero-parlor.dts | 2 +- arch/arm/boot/dts/omap4-var-om44customboard.dtsi | 2 +- arch/arm/boot/dts/omap5-cm-t54.dts | 2 +- 22 files changed, 57 insertions(+), 57 deletions(-) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index b017871aeddc..d8dcbaf23c8a 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -23,28 +23,28 @@ label = "sysboot2"; gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; sysboot5 { label = "sysboot5"; gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; gpio1 { label = "gpio1"; gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; gpio2 { label = "gpio2"; gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 5e0bf475051e..01e1e2d5c735 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -69,7 +69,7 @@ label = "user"; gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; linux,code = <0x114>; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 8dcf84ac79bb..8ba465d57635 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -80,7 +80,7 @@ label = "user"; gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; linux,code = <0x114>; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi index 8c813e77b17f..e5f7f5c92c1a 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi @@ -238,7 +238,7 @@ ti,debounce-tol = /bits/ 16 <10>; ti,debounce-rep = /bits/ 16 <1>; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi index 9ca2865a83d6..86850bb311eb 100644 --- a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi +++ b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi @@ -64,7 +64,7 @@ label = "user"; gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; linux,code = ; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi index 4813e96157b3..738910db5c0c 100644 --- a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi +++ b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi @@ -68,6 +68,6 @@ ti,keep-vref-on = <1>; ti,settle-delay-usec = /bits/ 16 <150>; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index e14d15e5abc8..5e2d6433d939 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -37,7 +37,7 @@ label = "aux"; linux,code = <169>; gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts index 0d0f1a7444f7..540163025dd3 100644 --- a/arch/arm/boot/dts/omap3-ldp.dts +++ b/arch/arm/boot/dts/omap3-ldp.dts @@ -35,63 +35,63 @@ label = "enter"; gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* gpio101 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_f1 { label = "f1"; gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* gpio102 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_f2 { label = "f2"; gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* gpio103 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_f3 { label = "f3"; gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* gpio104 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_f4 { label = "f4"; gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* gpio105 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_left { label = "left"; gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* gpio106 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_right { label = "right"; gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* gpio107 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_up { label = "up"; gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* gpio108 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; key_down { label = "down"; gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* gpio109 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi index 57d7c93cc72b..93f8dfe20f13 100644 --- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -327,7 +327,7 @@ ti,pressure-max = /bits/ 16 <255>; ti,swap-xy; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index f8a20f32e26c..74d8f7eb5563 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -67,28 +67,28 @@ gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */ linux,input-type = <5>; /* EV_SW */ linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */ - gpio-key,wakeup; + wakeup-source; }; camera_focus { label = "Camera Focus"; gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */ linux,code = <0x210>; /* KEY_CAMERA_FOCUS */ - gpio-key,wakeup; + wakeup-source; }; camera_capture { label = "Camera Capture"; gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */ linux,code = <0xd4>; /* KEY_CAMERA */ - gpio-key,wakeup; + wakeup-source; }; lock_button { label = "Lock Button"; gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */ linux,code = <0x98>; /* KEY_SCREENLOCK */ - gpio-key,wakeup; + wakeup-source; }; keypad_slide { @@ -96,7 +96,7 @@ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */ linux,input-type = <5>; /* EV_SW */ linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */ - gpio-key,wakeup; + wakeup-source; }; proximity_sensor { diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi index 7aae8fb82c1f..3b3a75997f81 100644 --- a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi @@ -48,7 +48,7 @@ label = "button0"; linux,code = ; gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* gpio_10 */ - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi index 17b82f82638a..7df27926ead2 100644 --- a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi @@ -41,13 +41,13 @@ label = "button0"; linux,code = ; gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ - gpio-key,wakeup; + wakeup-source; }; button1@14 { label = "button1"; linux,code = ; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi index b09cedf66117..6314da2580f5 100644 --- a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi +++ b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi @@ -161,6 +161,6 @@ ti,x-plate-ohms = /bits/ 16 <180>; ti,pressure-max = /bits/ 16 <255>; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi index 5f979590571b..7e3fe85a8ad9 100644 --- a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi +++ b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi @@ -172,7 +172,7 @@ ti,x-plate-ohms = /bits/ 16 <180>; ti,pressure-max = /bits/ 16 <255>; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi index 49d2254a99b0..250cc7fe5d5e 100644 --- a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi @@ -41,13 +41,13 @@ label = "button0"; linux,code = ; gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ - gpio-key,wakeup; + wakeup-source; }; button1@14 { label = "button1"; linux,code = ; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi b/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi index 680d7262399c..8df7ec35d17d 100644 --- a/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi @@ -41,13 +41,13 @@ label = "button0"; linux,code = ; gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ - gpio-key,wakeup; + wakeup-source; }; button1@14 { label = "button1"; linux,code = ; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi index 087aedf5b902..0ea2c451c809 100644 --- a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi @@ -41,13 +41,13 @@ label = "button0"; linux,code = ; gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ - gpio-key,wakeup; + wakeup-source; }; button1@14 { label = "button1"; linux,code = ; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ - gpio-key,wakeup; + wakeup-source; }; }; }; diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index cfe140c657e7..13e9d1f987af 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -84,112 +84,112 @@ label = "up"; linux,code = ; gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* GPIO_110 */ - gpio-key,wakeup; + wakeup-source; }; down-button { label = "down"; linux,code = ; gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* GPIO_103 */ - gpio-key,wakeup; + wakeup-source; }; left-button { label = "left"; linux,code = ; gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; /* GPIO_96 */ - gpio-key,wakeup; + wakeup-source; }; right-button { label = "right"; linux,code = ; gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; /* GPIO_98 */ - gpio-key,wakeup; + wakeup-source; }; pageup-button { label = "game 1"; linux,code = ; gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* GPIO_109 */ - gpio-key,wakeup; + wakeup-source; }; pagedown-button { label = "game 3"; linux,code = ; gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* GPIO_106 */ - gpio-key,wakeup; + wakeup-source; }; home-button { label = "game 4"; linux,code = ; gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* GPIO_101 */ - gpio-key,wakeup; + wakeup-source; }; end-button { label = "game 2"; linux,code = ; gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* GPIO_111 */ - gpio-key,wakeup; + wakeup-source; }; right-shift { label = "l"; linux,code = ; gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* GPIO_102 */ - gpio-key,wakeup; + wakeup-source; }; kp-plus { label = "l2"; linux,code = ; gpios = <&gpio4 1 GPIO_ACTIVE_LOW>; /* GPIO_97 */ - gpio-key,wakeup; + wakeup-source; }; right-ctrl { label = "r"; linux,code = ; gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* GPIO_105 */ - gpio-key,wakeup; + wakeup-source; }; kp-minus { label = "r2"; linux,code = ; gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* GPIO_107 */ - gpio-key,wakeup; + wakeup-source; }; left-ctrl { label = "ctrl"; linux,code = ; gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* GPIO_104 */ - gpio-key,wakeup; + wakeup-source; }; menu { label = "menu"; linux,code = ; gpios = <&gpio4 3 GPIO_ACTIVE_LOW>; /* GPIO_99 */ - gpio-key,wakeup; + wakeup-source; }; hold { label = "hold"; linux,code = ; gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* GPIO_176 */ - gpio-key,wakeup; + wakeup-source; }; left-alt { label = "alt"; linux,code = ; gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ - gpio-key,wakeup; + wakeup-source; }; lid { @@ -617,7 +617,7 @@ ti,x-plate-ohms = /bits/ 16 <40>; ti,pressure-max = /bits/ 16 <255>; - linux,wakeup; + wakeup-source; }; lcd: lcd@1 { diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi index f4b1a61853e3..157345bb8e79 100644 --- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi +++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi @@ -66,6 +66,6 @@ ti,x-plate-ohms = /bits/ 16 <40>; ti,pressure-max = /bits/ 16 <255>; ti,swap-xy; - linux,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap4-duovero-parlor.dts b/arch/arm/boot/dts/omap4-duovero-parlor.dts index 1a78f013f37a..ab17b9929250 100644 --- a/arch/arm/boot/dts/omap4-duovero-parlor.dts +++ b/arch/arm/boot/dts/omap4-duovero-parlor.dts @@ -36,7 +36,7 @@ label = "button0"; linux,code = ; gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */ - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi index f2d2fdb75628..6e278d7716a5 100644 --- a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi +++ b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi @@ -41,7 +41,7 @@ label = "user"; gpios = <&gpio6 24 GPIO_ACTIVE_HIGH>; /* gpio 184 */ linux,code = ; - gpio-key,wakeup; + wakeup-source; }; }; diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts index 0c03dca9ea04..ecc591dc0778 100644 --- a/arch/arm/boot/dts/omap5-cm-t54.dts +++ b/arch/arm/boot/dts/omap5-cm-t54.dts @@ -359,7 +359,7 @@ ti,debounce-tol = /bits/ 16 <10>; ti,debounce-rep = /bits/ 16 <1>; - linux,wakeup; + wakeup-source; }; }; -- cgit v1.2.3 From f3e1dee242054454ebe48551f0ad7848b46ee5e8 Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Sun, 13 Dec 2015 10:55:35 +0200 Subject: ARM: dts: cm-t335: add support for USB0 Enable USB0. Signed-off-by: Ilya Ledvich Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index 31ff1aa07b43..ae2366e1eb4c 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -237,6 +237,26 @@ }; }; +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + &epwmss0 { status = "okay"; -- cgit v1.2.3 From c6135a6fd1576e5daee67b0b2207f035a3eb4de0 Mon Sep 17 00:00:00 2001 From: Uri Mashiach Date: Sun, 13 Dec 2015 10:55:36 +0200 Subject: ARM: dts: cm-t335: add support for SBC-T335 Add basic support for the SBC-T335. CompuLab SBC-T335 is a single baseboard computer. The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354 SoC. Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- Documentation/devicetree/bindings/arm/omap/omap.txt | 3 +++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-sbc-t335.dts | 16 ++++++++++++++++ 3 files changed, 20 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-sbc-t335.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 0b2c946a0289..a2bd593881ca 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -141,6 +141,9 @@ Boards: - AM335X CM-T335 : System On Module, built around the Sitara AM3352/4 compatible = "compulab,cm-t335", "ti,am33xx" +- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4 + compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 1cfb2990c40f..297f68f82c98 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -467,6 +467,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-nano.dtb \ am335x-pepper.dtb \ am335x-shc.dtb \ + am335x-sbc-t335.dtb \ am335x-sl50.dtb \ am335x-wega-rdk.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ diff --git a/arch/arm/boot/dts/am335x-sbc-t335.dts b/arch/arm/boot/dts/am335x-sbc-t335.dts new file mode 100644 index 000000000000..9e98445e3784 --- /dev/null +++ b/arch/arm/boot/dts/am335x-sbc-t335.dts @@ -0,0 +1,16 @@ +/* + * am335x-sbc-t335.dts - Device Tree file for Compulab SBC-T335 + * + * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am335x-cm-t335.dts" + +/ { + model = "CompuLab CM-T335 on SB-T335"; + compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"; +}; -- cgit v1.2.3 From 98e5d8987cd35688003f672f049c15163552c4c3 Mon Sep 17 00:00:00 2001 From: Uri Mashiach Date: Sun, 13 Dec 2015 10:55:37 +0200 Subject: ARM: dts: cm-t335: add support for I2C GPIO expander The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module. Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-sbc-t335.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/am335x-sbc-t335.dts b/arch/arm/boot/dts/am335x-sbc-t335.dts index 9e98445e3784..4a5177e6030d 100644 --- a/arch/arm/boot/dts/am335x-sbc-t335.dts +++ b/arch/arm/boot/dts/am335x-sbc-t335.dts @@ -14,3 +14,14 @@ model = "CompuLab CM-T335 on SB-T335"; compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"; }; + +&i2c0 { + /* GPIO extender */ + gpio_ext: pca9555@26 { + compatible = "nxp,pca9555"; + pinctrl-names = "default"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x26>; + }; +}; -- cgit v1.2.3 From 3089e40e9f257569d414d2ad497752f741850be7 Mon Sep 17 00:00:00 2001 From: Uri Mashiach Date: Sun, 13 Dec 2015 10:55:38 +0200 Subject: ARM: dts: cm-t335: add support for DVI/LCD Add pinmux configuration for DVI/LCD. Add DRM display driver node with timing configurations for DVI and LCD. Add I2C GPIOs configurations for DVI and LCD enable. Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-sbc-t335.dts | 192 ++++++++++++++++++++++++++++++++++ 1 file changed, 192 insertions(+) diff --git a/arch/arm/boot/dts/am335x-sbc-t335.dts b/arch/arm/boot/dts/am335x-sbc-t335.dts index 4a5177e6030d..917d7ccc9109 100644 --- a/arch/arm/boot/dts/am335x-sbc-t335.dts +++ b/arch/arm/boot/dts/am335x-sbc-t335.dts @@ -13,6 +13,181 @@ / { model = "CompuLab CM-T335 on SB-T335"; compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"; + + /* DRM display driver */ + panel { + compatible = "ti,tilcdc,panel"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&lcd_pins_default>; + pinctrl-1 = <&lcd_pins_sleep>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + /* Timing selection performed by U-Boot */ + timing0: lcd {/* 800x480p62 */ + clock-frequency = <30000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <39>; + hback-porch = <39>; + hsync-len = <47>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <2>; + hsync-active = <1>; + vsync-active = <1>; + }; + timing1: dvi { /* 1024x768p60 */ + clock-frequency = <65000000>; + hactive = <1024>; + hfront-porch = <24>; + hback-porch = <160>; + hsync-len = <136>; + vactive = <768>; + vfront-porch = <3>; + vback-porch = <29>; + vsync-len = <6>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; +}; + +&am33xx_pinmux { + /* Display */ + lcd_pins_default: lcd_pins_default { + pinctrl-single,pins = < + /* gpmc_ad8.lcd_data23 */ + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad9.lcd_data22 */ + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad10.lcd_data21 */ + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad11.lcd_data20 */ + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad12.lcd_data19 */ + AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad13.lcd_data18 */ + AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad14.lcd_data17 */ + AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad15.lcd_data16 */ + AM33XX_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1) + /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) + /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) + /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) + /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) + /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) + /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) + /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) + /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) + /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) + /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) + /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) + /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) + /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) + /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) + /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) + /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) + /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) + /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) + /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) + /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) + >; + }; + + lcd_pins_sleep: lcd_pins_sleep { + pinctrl-single,pins = < + /* gpmc_ad8.lcd_data23 */ + AM33XX_IOPAD(0x820, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad9.lcd_data22 */ + AM33XX_IOPAD(0x824, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad10.lcd_data21 */ + AM33XX_IOPAD(0x828, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad11.lcd_data20 */ + AM33XX_IOPAD(0x82c, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad12.lcd_data19 */ + AM33XX_IOPAD(0x830, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad13.lcd_data18 */ + AM33XX_IOPAD(0x834, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad14.lcd_data17 */ + AM33XX_IOPAD(0x838, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* gpmc_ad15.lcd_data16 */ + AM33XX_IOPAD(0x83c, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a0, PULL_DISABLE | MUX_MODE7) + /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a4, PULL_DISABLE | MUX_MODE7) + /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8a8, PULL_DISABLE | MUX_MODE7) + /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8ac, PULL_DISABLE | MUX_MODE7) + /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b0, PULL_DISABLE | MUX_MODE7) + /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b4, PULL_DISABLE | MUX_MODE7) + /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8b8, PULL_DISABLE | MUX_MODE7) + /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8bc, PULL_DISABLE | MUX_MODE7) + /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c0, PULL_DISABLE | MUX_MODE7) + /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c4, PULL_DISABLE | MUX_MODE7) + /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8c8, PULL_DISABLE | MUX_MODE7) + /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8cc, PULL_DISABLE | MUX_MODE7) + /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d0, PULL_DISABLE | MUX_MODE7) + /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d4, PULL_DISABLE | MUX_MODE7) + /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8d8, PULL_DISABLE | MUX_MODE7) + /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8dc, PULL_DISABLE | MUX_MODE7) + /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | MUX_MODE7) + /* lcd_ac_bias_en.lcd_ac_bias_en */ + AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; }; &i2c0 { @@ -23,5 +198,22 @@ gpio-controller; #gpio-cells = <2>; reg = <0x26>; + dvi_ena { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "dvi-enable"; + }; + lcd_ena { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "lcd-enable"; + }; }; }; + +/* Display */ +&lcdc { + status = "okay"; +}; -- cgit v1.2.3 From d284aa27d9360ff5009886c4335988f366e7fa50 Mon Sep 17 00:00:00 2001 From: Uri Mashiach Date: Sun, 13 Dec 2015 10:55:39 +0200 Subject: ARM: dts: cm-t335: add support for bluetooth bluetooth HW is WLS1271 chip connected to UART1. Device tree modifications: - Pinmux for UART1. - Pinmux for bluetooth enable GPIO. Bluetooth enable GPIO is set to enable during startup by setting the relevant pinmux pin to pull-up. Signed-off-by: Uri Mashiach Acked-by: Igor Grinberg Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-cm-t335.dts | 31 ++++++++++++++++++++++++++++++- 1 file changed, 30 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts index ae2366e1eb4c..42e9b665582a 100644 --- a/arch/arm/boot/dts/am335x-cm-t335.dts +++ b/arch/arm/boot/dts/am335x-cm-t335.dts @@ -50,7 +50,7 @@ &am33xx_pinmux { pinctrl-names = "default"; - pinctrl-0 = <>; + pinctrl-0 = <&bluetooth_pins>; i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < @@ -121,6 +121,19 @@ >; }; + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + /* uart1_ctsn.uart1_ctsn */ + AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0) + /* uart1_rtsn.uart1_rtsn */ + AM33XX_IOPAD(0x97C, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + /* uart1_rxd.uart1_rxd */ + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart1_txd.uart1_txd */ + AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) + >; + }; + ecap0_pins: pinmux_ecap0_pins { pinctrl-single,pins = < /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ @@ -209,6 +222,14 @@ AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) >; }; + + /* wl1271 bluetooth */ + bluetooth_pins: pinmux_bluetooth_pins { + pinctrl-single,pins = < + /* XDMA_EVENT_INTR0.gpio0_19 - bluetooth enable */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE7) + >; + }; }; &uart0 { @@ -218,6 +239,14 @@ status = "okay"; }; +/* WLS1271 bluetooth */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + +status = "okay"; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; -- cgit v1.2.3 From 60db554de357f62c2fe07eeeaae143099fa4b021 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Wed, 16 Dec 2015 21:18:29 -0600 Subject: ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support Add basic support for Logic PD type 15 display for older development kits. This uses GPIO for the backlight. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 100 ++++++++++++++++++++++ 1 file changed, 100 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index d8dcbaf23c8a..c54f7720ac91 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -114,6 +114,70 @@ }; }; +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "gpio-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + + gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>, /* gpio_56 */ + <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + default-on; + }; +}; + &mmc1 { interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; pinctrl-names = "default"; @@ -149,6 +213,42 @@ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ >; }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */ + >; + }; }; &omap3_pmx_wkup { -- cgit v1.2.3 From 485fa1261f780e8a13d0b25a24673947e6c50953 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Wed, 16 Dec 2015 15:34:15 -0600 Subject: ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth Bindings for the WL1283 Bluetooth was removed from the shared transport driver in commit c0bd1b9e5895 ("Revert ti-st: add device tree support") Until we havea better binding, we need to use the platform data to initialize Bluetooth. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/pdata-quirks.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 1dfe34654c43..cd9775a4459d 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -153,6 +153,21 @@ static struct platform_device wl18xx_device = { } }; +static struct ti_st_plat_data wilink7_pdata = { + .nshutdown_gpio = 162, + .dev_name = "/dev/ttyO1", + .flow_cntrl = 1, + .baud_rate = 300000, +}; + +static struct platform_device wl128x_device = { + .name = "kim", + .id = -1, + .dev = { + .platform_data = &wilink7_pdata, + } +}; + static struct platform_device btwilink_device = { .name = "btwilink", .id = -1, @@ -279,6 +294,13 @@ static void __init omap3_tao3530_legacy_init(void) hsmmc2_internal_input_clk(); } +static void __init omap3_logicpd_torpedo_init(void) +{ + omap3_gpio126_127_129(); + platform_device_register(&wl128x_device); + platform_device_register(&btwilink_device); +} + /* omap3pandora legacy devices */ #define PANDORA_WIFI_IRQ_GPIO 21 #define PANDORA_WIFI_NRESET_GPIO 23 @@ -529,7 +551,7 @@ static struct pdata_init pdata_quirks[] __initdata = { { "nokia,omap3-n950", hsmmc2_internal_input_clk, }, { "isee,omap3-igep0020-rev-f", omap3_igep0020_rev_f_legacy_init, }, { "isee,omap3-igep0030-rev-g", omap3_igep0030_rev_g_legacy_init, }, - { "logicpd,dm3730-torpedo-devkit", omap3_gpio126_127_129, }, + { "logicpd,dm3730-torpedo-devkit", omap3_logicpd_torpedo_init, }, { "ti,omap3-evm-37xx", omap3_evm_legacy_init, }, { "ti,am3517-evm", am3517_evm_legacy_init, }, { "technexion,omap3-tao3530", omap3_tao3530_legacy_init, }, -- cgit v1.2.3 From d01d8799308f53f2a350ec48ae3a98f4b803dac1 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 17 Dec 2015 18:52:16 -0600 Subject: ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo") because it It was already done and it's just a duplicate. See: 2d11961f3e55 ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively") Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 10 ---------- 1 file changed, 10 deletions(-) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index c54f7720ac91..6854bda5063f 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -83,16 +83,6 @@ regulator-max-microvolt = <1800000>; }; -&vaux1 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; -}; - -&vaux4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; -}; - &mcbsp2 { status = "okay"; }; -- cgit v1.2.3 From dfd35b779d6c8bbf9f287e1abec533374c41b8ae Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 17 Dec 2015 23:38:18 +0000 Subject: ARM: socfpga: Repair incorrectly applied MCV patch For whatever reason, this patch was not applied verbatim and had all tabs replaced with spaces. Replace them back by a quick sed. Signed-off-by: Marek Vasut Cc: Alan Tull Cc: Dinh Nguyen Cc: Olof Johansson Cc: Steffen Trumtrar Cc: Thor Thayer Cc: Vince Bridgers Signed-off-by: Dinh Nguyen --- arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi | 18 +++--- arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts | 90 +++++++++++++-------------- 2 files changed, 54 insertions(+), 54 deletions(-) diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi index f0e03a23a864..baecd983d056 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi +++ b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi @@ -18,16 +18,16 @@ #include "socfpga_cyclone5.dtsi" / { - model = "DENX MCV"; - compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + model = "DENX MCV"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; - memory { - name = "memory"; - device_type = "memory"; - reg = <0x0 0x40000000>; /* 1 GiB */ - }; + memory { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1 GiB */ + }; }; -&mmc0 { /* On-SoM eMMC */ - bus-width = <8>; +&mmc0 { /* On-SoM eMMC */ + bus-width = <8>; }; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts b/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts index 09d0deddcbf9..7186a29b8b86 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts @@ -18,77 +18,77 @@ #include "socfpga_cyclone5_mcv.dtsi" / { - model = "DENX MCV EVK"; - compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + model = "DENX MCV EVK"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; - aliases { - ethernet0 = &gmac0; - stmpe-i2c0 = &stmpe1; - }; + aliases { + ethernet0 = &gmac0; + stmpe-i2c0 = &stmpe1; + }; - chosen { - stdout-path = "serial0:115200n8"; - }; + chosen { + stdout-path = "serial0:115200n8"; + }; }; &can0 { - status = "okay"; + status = "okay"; }; &can1 { - status = "okay"; + status = "okay"; }; &gmac0 { - phy-mode = "rgmii"; - status = "okay"; + phy-mode = "rgmii"; + status = "okay"; }; -&gpio0 { /* GPIO 0 ... 28 */ - status = "okay"; +&gpio0 { /* GPIO 0 ... 28 */ + status = "okay"; }; -&gpio1 { /* GPIO 29 ... 57 */ - status = "okay"; +&gpio1 { /* GPIO 29 ... 57 */ + status = "okay"; }; -&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ - status = "okay"; +&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ + status = "okay"; }; &i2c0 { - status = "okay"; - speed-mode = <0>; + status = "okay"; + speed-mode = <0>; - stmpe1: stmpe811@41 { - compatible = "st,stmpe811"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x41>; - id = <0>; - blocks = <0x5>; - irq-gpio = <&portb 28 0x4>; /* GPIO 57, trig. level HI */ + stmpe1: stmpe811@41 { + compatible = "st,stmpe811"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + id = <0>; + blocks = <0x5>; + irq-gpio = <&portb 28 0x4>; /* GPIO 57, trig. level HI */ - stmpe_touchscreen { - compatible = "st,stmpe-ts"; - reg = <0>; - ts,sample-time = <4>; - ts,mod-12b = <1>; - ts,ref-sel = <0>; - ts,adc-freq = <1>; - ts,ave-ctrl = <1>; - ts,touch-det-delay = <3>; - ts,settling = <4>; - ts,fraction-z = <7>; - ts,i-drive = <1>; - }; - }; + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + reg = <0>; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <3>; + ts,settling = <4>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; }; &uart0 { - status = "okay"; + status = "okay"; }; &usb1 { - status = "okay"; + status = "okay"; }; -- cgit v1.2.3 From 1929d0b5a821ed5bec3d1e683e63851fc51d05ee Mon Sep 17 00:00:00 2001 From: Vignesh R Date: Fri, 11 Dec 2015 09:39:59 +0530 Subject: ARM: dts: DRA7: add entry for qspi mmap region Add qspi memory mapped region entries for DRA7xx based SoCs. Also, update the binding documents for the controller to document this change. Signed-off-by: Vignesh R Acked-by: Rob Herring Signed-off-by: Tony Lindgren --- Documentation/devicetree/bindings/spi/ti_qspi.txt | 17 +++++++++++++++++ arch/arm/boot/dts/dra7.dtsi | 6 ++++-- 2 files changed, 21 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 601a360531a5..809c3f334316 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -15,6 +15,10 @@ Recommended properties: - spi-max-frequency: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +Optional properties: +- syscon-chipselects: Handle to system control region contains QSPI + chipselect register and offset of that register. + Example: qspi: qspi@4b300000 { @@ -26,3 +30,16 @@ qspi: qspi@4b300000 { spi-max-frequency = <25000000>; ti,hwmods = "qspi"; }; + +For dra7xx: +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>, + <0x5c000000 0x4000000>, + reg-names = "qspi_base", "qspi_mmap"; + syscon-chipselects = <&scm_conf 0x558>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <48000000>; + ti,hwmods = "qspi"; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index b2badf9110f7..bf5dd1e9508a 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -1154,8 +1154,10 @@ qspi: qspi@4b300000 { compatible = "ti,dra7xxx-qspi"; - reg = <0x4b300000 0x100>; - reg-names = "qspi_base"; + reg = <0x4b300000 0x100>, + <0x5c000000 0x4000000>; + reg-names = "qspi_base", "qspi_mmap"; + syscon-chipselects = <&scm_conf 0x558>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "qspi"; -- cgit v1.2.3 From 2acb6c3ef81486781ffe08145c17b7dc1904e741 Mon Sep 17 00:00:00 2001 From: Vignesh R Date: Fri, 11 Dec 2015 09:40:00 +0530 Subject: ARM: dts: AM4372: add entry for qspi mmap region Add qspi memory mapped region entries for AM43xx based SoCs. Also, update the binding documents for the controller to document this change. Acked-by: Rob Herring Signed-off-by: Vignesh R Signed-off-by: Tony Lindgren --- Documentation/devicetree/bindings/spi/ti_qspi.txt | 5 +++-- arch/arm/boot/dts/am4372.dtsi | 4 +++- 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 809c3f334316..cc8304aa64ac 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -21,9 +21,10 @@ Optional properties: Example: +For am4372: qspi: qspi@4b300000 { - compatible = "ti,dra7xxx-qspi"; - reg = <0x47900000 0x100>, <0x30000000 0x3ffffff>; + compatible = "ti,am4372-qspi"; + reg = <0x47900000 0x100>, <0x30000000 0x4000000>; reg-names = "qspi_base", "qspi_mmap"; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index a2c9b7da0d9c..dcae0d60ed87 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -1006,7 +1006,9 @@ qspi: qspi@47900000 { compatible = "ti,am4372-qspi"; - reg = <0x47900000 0x100>; + reg = <0x47900000 0x100>, + <0x30000000 0x4000000>; + reg-names = "qspi_base", "qspi_mmap"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "qspi"; -- cgit v1.2.3 From 6686f744df70c46cff061d0120616eff78dd04f4 Mon Sep 17 00:00:00 2001 From: Keerthy Date: Mon, 14 Dec 2015 12:06:56 +0530 Subject: ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2 Add regulator-allow-bypass property for ldo1 and ldo2. Signed-off-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra72-evm.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index ae3502a0267d..00b12002c07c 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -373,6 +373,7 @@ regulator-max-microvolt = <3300000>; regulator-always-on; regulator-boot-on; + regulator-allow-bypass; }; ldo2_reg: ldo2 { @@ -380,6 +381,7 @@ regulator-name = "ldo2"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; + regulator-allow-bypass; }; ldo3_reg: ldo3 { -- cgit v1.2.3 From fcf589581b3b96fbc3abef716553a182e1156d60 Mon Sep 17 00:00:00 2001 From: Keerthy Date: Mon, 14 Dec 2015 12:06:57 +0530 Subject: ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9 Add regulator-allow-bypass property for ldo9. Signed-off-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 53b3a4b97086..cfc24e52244e 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -504,6 +504,7 @@ regulator-max-microvolt = <1050000>; regulator-always-on; regulator-boot-on; + regulator-allow-bypass; }; ldoln_reg: ldoln { -- cgit v1.2.3 From a692e00a778997ea84238aac803fa4a5cd562fc8 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 11 Dec 2015 19:43:58 +0100 Subject: ARM: dts: sun5i: Enable onboard codec used on the UTOO P66 tablet The UTOO P66 tablet uses the A13's integrated audio codec, enable it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i-a13-utoo-p66.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts index 5236c1e3a1b5..fa9ddfdcfe96 100644 --- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts +++ b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts @@ -73,6 +73,13 @@ }; }; +&codec { + pinctrl-names = "default"; + pinctrl-0 = <&codec_pa_pin>; + allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */ + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; @@ -168,6 +175,13 @@ }; &pio { + codec_pa_pin: codec_pa_pin@0 { + allwinner,pins = "PG3"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + mmc0_cd_pin_p66: mmc0_cd_pin@0 { allwinner,pins = "PG0"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From 53aa9346098a15df9227e232236f4ada298ef6fc Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 11 Dec 2015 19:43:59 +0100 Subject: ARM: dts: sun4i: Enable onboard codec used on the pov protab2-ips9 tablet The pov protab2-ips9 tablet uses the A10's integrated audio codec, enable it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts index 1f92ec7c82e8..918f97294b33 100644 --- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -72,6 +72,13 @@ }; }; +&codec { + pinctrl-names = "default"; + pinctrl-0 = <&codec_pa_pin>; + allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */ + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; @@ -163,6 +170,13 @@ allwinner,pull = ; }; + codec_pa_pin: codec_pa_pin@0 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + touchscreen_pins: touchscreen_pins@0 { allwinner,pins = "PA5", "PB13"; allwinner,function = "gpio_out"; -- cgit v1.2.3 From 2c102c38d5ee4e6d3f428eed563a95bc2b3c2561 Mon Sep 17 00:00:00 2001 From: Priit Laes Date: Fri, 11 Dec 2015 23:23:00 +0200 Subject: ARM: dts: sun4i: gemei-g9: Enable PA GPIO pin configuration PA GPIO pin (PH15) controls power to external amplifier (FT2012Q). Signed-off-by: Priit Laes Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-gemei-g9.dts | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 1d73a9897b71..ac64781a0a9c 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -65,13 +65,16 @@ /* * TODO: * 2x cameras via CSI - * audio input * AXP battery management * NAND * OTG * Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48 */ &codec { + /* PH15 controls power to external amplifier (ft2012q) */ + pinctrl-names = "default"; + pinctrl-0 = <&codec_pa_pin>; + allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; status = "okay"; }; @@ -151,6 +154,15 @@ status = "okay"; }; +&pio { + codec_pa_pin: codec_pa_pin@0 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; -- cgit v1.2.3 From 0e710f1f5b1640ab033db9aba0edb2bd215fac26 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Fri, 18 Dec 2015 11:52:08 +0300 Subject: ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming Signed-off-by: Aleksei Mamlin Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 239b5d2915a4..119713bb6710 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -154,6 +154,12 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; -- cgit v1.2.3 From 68556dd775ba928ec70ef7d43bc348b8704bc39f Mon Sep 17 00:00:00 2001 From: Xing Zheng Date: Thu, 17 Dec 2015 22:21:47 +0800 Subject: ARM: dts: rockchip: fix the pinctrl bias settings for rk3036 The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs can't set the status in the internal. We should keep the default status for enable the gpio status, In fact, the pull_none is the disable the gpio pull up/down. Signed-off-by: Xing Zheng Signed-off-by: Caesar Wang Reviewed-by: Kees Cook Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3036.dtsi | 34 +++++++++++++++------------------- 1 file changed, 15 insertions(+), 19 deletions(-) diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index f8758bf15933..620e6e04edd0 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -427,12 +427,8 @@ #interrupt-cells = <2>; }; - pcfg_pull_up: pcfg-pull-up { - bias-pull-up; - }; - - pcfg_pull_down: pcfg-pull-down { - bias-pull-down; + pcfg_pull_default: pcfg_pull_default { + bias-pull-pin-default; }; pcfg_pull_none: pcfg-pull-none { @@ -473,18 +469,18 @@ }; emmc_cmd: emmc-cmd { - rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_none>; + rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_default>; }; emmc_bus8: emmc-bus8 { - rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>, - <1 25 RK_FUNC_2 &pcfg_pull_none>, - <1 26 RK_FUNC_2 &pcfg_pull_none>, - <1 27 RK_FUNC_2 &pcfg_pull_none>, - <1 28 RK_FUNC_2 &pcfg_pull_none>, - <1 29 RK_FUNC_2 &pcfg_pull_none>, - <1 30 RK_FUNC_2 &pcfg_pull_none>, - <1 31 RK_FUNC_2 &pcfg_pull_none>; + rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_default>, + <1 25 RK_FUNC_2 &pcfg_pull_default>, + <1 26 RK_FUNC_2 &pcfg_pull_default>, + <1 27 RK_FUNC_2 &pcfg_pull_default>, + <1 28 RK_FUNC_2 &pcfg_pull_default>, + <1 29 RK_FUNC_2 &pcfg_pull_default>, + <1 30 RK_FUNC_2 &pcfg_pull_default>, + <1 31 RK_FUNC_2 &pcfg_pull_default>; }; }; @@ -522,12 +518,12 @@ uart0 { uart0_xfer: uart0-xfer { - rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_up>, + rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_default>, <0 17 RK_FUNC_1 &pcfg_pull_none>; }; uart0_cts: uart0-cts { - rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_up>; + rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_default>; }; uart0_rts: uart0-rts { @@ -537,7 +533,7 @@ uart1 { uart1_xfer: uart1-xfer { - rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_none>, + rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_default>, <2 23 RK_FUNC_1 &pcfg_pull_none>; }; /* no rts / cts for uart1 */ @@ -545,7 +541,7 @@ uart2 { uart2_xfer: uart2-xfer { - rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>, + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_default>, <1 19 RK_FUNC_2 &pcfg_pull_none>; }; /* no rts / cts for uart2 */ -- cgit v1.2.3 From 187d7967a5ee630ae062fb543655e59d2f0f91fb Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Thu, 17 Dec 2015 22:21:49 +0800 Subject: ARM: dts: rockchip: add the sdio/sdmmc node for rk3036 In general, the sdio/sdmmc is used by the wifi module and sd card. let's add the node for these function. Signed-off-by: Caesar Wang Reviewed-by: Kees Cook Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3036.dtsi | 72 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 72 insertions(+) diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index 620e6e04edd0..b9567c1e0687 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -55,6 +55,8 @@ i2c1 = &i2c1; i2c2 = &i2c2; mshc0 = &emmc; + mshc1 = &sdmmc; + mshc2 = &sdio; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; @@ -184,6 +186,30 @@ status = "disabled"; }; + sdmmc: dwmmc@10214000 { + compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc"; + reg = <0x10214000 0x4000>; + clock-frequency = <37500000>; + clock-freq-min-max = <400000 37500000>; + clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>; + clock-names = "biu", "ciu"; + fifo-depth = <0x100>; + interrupts = ; + status = "disabled"; + }; + + sdio: dwmmc@10218000 { + compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc"; + reg = <0x10218000 0x4000>; + clock-freq-min-max = <400000 37500000>; + clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>, + <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; + clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; + fifo-depth = <0x100>; + interrupts = ; + status = "disabled"; + }; + emmc: dwmmc@1021c000 { compatible = "rockchip,rk3288-dw-mshc"; reg = <0x1021c000 0x4000>; @@ -459,6 +485,52 @@ }; }; + sdmmc { + sdmmc_clk: sdmmc-clk { + rockchip,pins = <1 16 RK_FUNC_1 &pcfg_pull_none>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = <1 15 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdmmc_cd: sdmcc-cd { + rockchip,pins = <1 17 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdmmc_bus1: sdmmc-bus1 { + rockchip,pins = <1 18 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = <1 18 RK_FUNC_1 &pcfg_pull_default>, + <1 19 RK_FUNC_1 &pcfg_pull_default>, + <1 20 RK_FUNC_1 &pcfg_pull_default>, + <1 21 RK_FUNC_1 &pcfg_pull_default>; + }; + }; + + sdio { + sdio_bus1: sdio-bus1 { + rockchip,pins = <0 11 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdio_bus4: sdio-bus4 { + rockchip,pins = <0 11 RK_FUNC_1 &pcfg_pull_default>, + <0 12 RK_FUNC_1 &pcfg_pull_default>, + <0 13 RK_FUNC_1 &pcfg_pull_default>, + <0 14 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdio_cmd: sdio-cmd { + rockchip,pins = <0 8 RK_FUNC_1 &pcfg_pull_default>; + }; + + sdio_clk: sdio-clk { + rockchip,pins = <0 9 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + emmc { /* * We run eMMC at max speed; bump up drive strength. -- cgit v1.2.3 From 94cf32b97bbb043b99e914aacff1a6d7833daf58 Mon Sep 17 00:00:00 2001 From: Caesar Wang Date: Thu, 17 Dec 2015 22:21:50 +0800 Subject: ARM: dts: rockchip: add the kylin board for rk3036 This patchset is the initiation version to try work for kylin board. Signed-off-by: Caesar Wang Reviewed-by: Kees Cook Acked-by: Rob Herring Signed-off-by: Heiko Stuebner --- Documentation/devicetree/bindings/arm/rockchip.txt | 4 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3036-kylin.dts | 300 +++++++++++++++++++++ 3 files changed, 305 insertions(+) create mode 100644 arch/arm/boot/dts/rk3036-kylin.dts diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 56a12defd87b..c980b2b81227 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -1,6 +1,10 @@ Rockchip platforms device tree bindings --------------------------------------- +- Kylin RK3036 board: + Required root node properties: + - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036"; + - MarsBoard RK3066 board: Required root node properties: - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a"; diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 37a74e9b667e..bf5470c577f9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -513,6 +513,7 @@ dtb-$(CONFIG_ARCH_REALVIEW) += \ arm-realview-pb1176.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3036-evb.dtb \ + rk3036-kylin.dtb \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ rk3066a-rayeager.dtb \ diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rk3036-kylin.dts new file mode 100644 index 000000000000..992f9cadbc04 --- /dev/null +++ b/arch/arm/boot/dts/rk3036-kylin.dts @@ -0,0 +1,300 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3036.dtsi" + +/ { + model = "Rockchip RK3036 KylinBoard"; + compatible = "rockchip,rk3036-kylin", "rockchip,rk3036"; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&acodec { + status = "okay"; +}; + +&emmc { + status = "okay"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + rk808: pmic@1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio2>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk808-clkout2"; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc11-supply = <&vcc_sys>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vccio_pmu>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vccio_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_tp: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vout5: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vout5"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&sdio { + status = "okay"; + + broken-cd; + bus-width = <4>; + cap-sdio-irq; + default-sample-phase = <90>; + keep-power-in-suspend; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdio_clk &sdio_cmd &sdio_bus4>; +}; + +&uart2 { + status = "okay"; +}; + +&usb_host { + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&pinctrl { + pmic { + pmic_int: pmic-int { + rockchip,pins = <2 2 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + sleep { + global_pwroff: global-pwroff { + rockchip,pins = <2 7 RK_FUNC_1 &pcfg_pull_none>; + }; + }; +}; -- cgit v1.2.3 From 91f69147d681e47e2aa2ff7dbf4c5468befa8a1b Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Mon, 21 Dec 2015 00:42:01 -0600 Subject: ARM: socfpga: dts: Enable MMC support at correct place in the DT The socfpga.dtsi explicitly enabled MMC support, but not all boards are equiped with an MMC card. There are setups which only have QSPI NOR. Therefore, disable the MMC support on socfpga.dtsi level and enable it on per-board basis. Signed-off-by: Marek Vasut Cc: Alan Tull Cc: Dinh Nguyen Cc: Marek Vasut Cc: Olof Johansson Cc: Thor Thayer Cc: Vince Bridgers Signed-off-by: Dinh Nguyen --- arch/arm/boot/dts/socfpga.dtsi | 1 + arch/arm/boot/dts/socfpga_arria5_socdk.dts | 1 + arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dts | 1 + arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi | 1 + arch/arm/boot/dts/socfpga_cyclone5_socdk.dts | 1 + arch/arm/boot/dts/socfpga_cyclone5_sockit.dts | 1 + 6 files changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 39c470e291f9..3ed4abdaaa9c 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -677,6 +677,7 @@ #size-cells = <0>; clocks = <&l4_mp_clk>, <&sdmmc_clk_divided>; clock-names = "biu", "ciu"; + status = "disabled"; }; ocram: sram@ffff0000 { diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/socfpga_arria5_socdk.dts index a75a666032b2..3c8867862b0d 100644 --- a/arch/arm/boot/dts/socfpga_arria5_socdk.dts +++ b/arch/arm/boot/dts/socfpga_arria5_socdk.dts @@ -79,6 +79,7 @@ &mmc0 { vmmc-supply = <®ulator_3_3v>; vqmmc-supply = <®ulator_3_3v>; + status = "okay"; }; &usb1 { diff --git a/arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dts index 555e9caf21e1..afea3645ada4 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dts @@ -100,6 +100,7 @@ &mmc0 { vmmc-supply = <®ulator_3_3v>; vqmmc-supply = <®ulator_3_3v>; + status = "okay"; }; &uart0 { diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi index baecd983d056..f86f9c060d7a 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi +++ b/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi @@ -30,4 +30,5 @@ &mmc0 { /* On-SoM eMMC */ bus-width = <8>; + status = "okay"; }; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts index d4d0a28fb331..15e43f43f244 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts @@ -84,6 +84,7 @@ cd-gpios = <&portb 18 0>; vmmc-supply = <®ulator_3_3v>; vqmmc-supply = <®ulator_3_3v>; + status = "okay"; }; &usb1 { diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts index 48bf651bd762..b61f22f9ac9f 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts @@ -80,6 +80,7 @@ &mmc0 { vmmc-supply = <®ulator_3_3v>; vqmmc-supply = <®ulator_3_3v>; + status = "okay"; }; &usb1 { -- cgit v1.2.3 From 3869394ae461a41bb2b2bff98adfe6020b47e635 Mon Sep 17 00:00:00 2001 From: Gregory CLEMENT Date: Thu, 17 Dec 2015 11:19:19 +0100 Subject: ARM: at91/dt: Add Support for the L+G VInCo platform The Versatile Industrial Communication platform is a community oriented board from Landis + Gyr. It comes with: - an RS-485 port - 2 Ethernet ports - a wireless M-BUS - a 4G modem - a 4MB SPI flash - a 4GB eMMC Signed-off-by: Gregory CLEMENT Signed-off-by: Alexandre Belloni --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/at91-vinco.dts | 256 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 258 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/at91-vinco.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 0e965358304b..c7e0ec5678be 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -50,7 +50,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d36ek.dtb \ at91-sama5d4_ma5d4evk.dtb \ at91-sama5d4_xplained.dtb \ - at91-sama5d4ek.dtb + at91-sama5d4ek.dtb \ + at91-vinco.dtb dtb-$(CONFIG_ARCH_ATLAS6) += \ atlas6-evb.dtb dtb-$(CONFIG_ARCH_ATLAS7) += \ diff --git a/arch/arm/boot/dts/at91-vinco.dts b/arch/arm/boot/dts/at91-vinco.dts new file mode 100644 index 000000000000..79aec55e1ebc --- /dev/null +++ b/arch/arm/boot/dts/at91-vinco.dts @@ -0,0 +1,256 @@ +/* + * Device Tree file for VInCo platform + * + * Copyright (C) 2014 Atmel, + * 2014 Nicolas Ferre + * 2015 Gregory CLEMENT + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; +#include "sama5d4.dtsi" + +/ { + model = "L+G VInCo platform"; + compatible = "l+g,vinco", "atmel,sama5d4", "atmel,sama5"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + + adc0: adc@fc034000 { + status = "okay"; /* Enable ADC IIO support */ + }; + + mmc0: mmc@f8000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 + &pinctrl_mmc0_dat1_3 + &pinctrl_mmc0_dat4_7>; + vqmmc-supply = <&vcc_3v3_reg>; + vmmc-supply = <&vcc_3v3_reg>; + no-1-8-v; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <8>; + non-removable; + broken-cd; + status = "okay"; + }; + }; + + spi0: spi@f8010000 { + cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; + status = "okay"; + m25p80@0 { + compatible = "n25q32b", "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; + + i2c0: i2c@f8014000 { + status = "okay"; + }; + + i2c1: i2c@f8018000 { + status = "okay"; + /* kerkey security module */ + }; + + macb0: ethernet@f8020000 { + phy-mode = "rmii"; + status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + reset-gpios = <&pioE 8 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&pioB>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + }; + + }; + + i2c2: i2c@f8024000 { + status = "okay"; + + rtc1: rtc@64 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; + }; + + usart2: serial@fc008000 { + /* MBUS */ + status = "okay"; + }; + + usart3: serial@fc00c000 { + /* debug */ + status = "okay"; + }; + + usart4: serial@fc010000 { + /* LMN */ + pinctrl-0 = <&pinctrl_usart4 &pinctrl_usart4_rts>; + linux,rs485-enabled-at-boot-time; + status = "okay"; + }; + + macb1: ethernet@fc028000 { + phy-mode = "rmii"; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + interrupt-parent = <&pioB>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&pioE 6 GPIO_ACTIVE_HIGH>; + }; + }; + + watchdog@fc068640 { + status = "okay"; + }; + + pinctrl@fc06a000 { + board { + pinctrl_usba_vbus: usba_vbus { + atmel,pins = + ; + }; + }; + }; + }; + + usb0: gadget@00400000 { + atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "disable"; + }; + + usb1: ohci@00500000 { + num-ports = <3>; + atmel,vbus-gpio = <0 + &pioE 11 GPIO_ACTIVE_LOW + &pioE 12 GPIO_ACTIVE_LOW + >; + status = "disable"; + }; + + usb2: ehci@00600000 { + /* 4G Modem */ + status = "okay"; + }; + + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + led_err { + label = "err"; + gpios = <&pioA 7 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_rssi { + label = "rssi"; + gpios = <&pioA 9 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_tls { + label = "tls"; + gpios = <&pioA 24 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_lmc { + label = "lmc"; + gpios = <&pioA 25 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_wmt { + label = "wmt"; + gpios = <&pioA 29 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_pwr { + label = "pwr"; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + }; + + vcc_3v3_reg: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "VCC 3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; +}; -- cgit v1.2.3 From e7bb896a7fabdf05fb0126f9f5a489cb987f2152 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Fri, 18 Dec 2015 11:51:50 +0300 Subject: ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet Signed-off-by: Aleksei Mamlin Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 119713bb6710..1dc90796dcaa 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -102,6 +102,18 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins_a>; status = "okay"; + + gt911: touchscreen@5d { + compatible = "goodix,gt911"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_reset_pin>; + irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */ + reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */ + touchscreen-swapped-x-y; + }; }; &lradc { @@ -146,6 +158,13 @@ }; &pio { + ts_reset_pin: ts_reset_pin@0 { + allwinner,pins = "PB13"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH4"; allwinner,function = "gpio_in"; -- cgit v1.2.3 From 028997bb92a5bcc5d8ec936f7d522910c16c2579 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Fri, 18 Dec 2015 11:52:22 +0300 Subject: ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet Signed-off-by: Aleksei Mamlin Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 1dc90796dcaa..f47e5f1ef78b 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -48,6 +48,7 @@ #include #include #include +#include / { model = "Wexler TAB7200"; @@ -57,6 +58,16 @@ serial0 = &uart0; }; + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + pinctrl-names = "default"; + pinctrl-0 = <&bl_enable_pin>; + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + }; + chosen { stdout-path = "serial0:115200n8"; }; @@ -158,6 +169,13 @@ }; &pio { + bl_enable_pin: bl_enable_pin@0 { + allwinner,pins = "PH7"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + ts_reset_pin: ts_reset_pin@0 { allwinner,pins = "PB13"; allwinner,function = "gpio_out"; -- cgit v1.2.3 From 9f483c717d02d7f079b5285b1a0cdf8ff401c3a0 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Fri, 18 Dec 2015 11:52:45 +0300 Subject: ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet Signed-off-by: Aleksei Mamlin Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index f47e5f1ef78b..2f6b21adddd9 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -74,6 +74,9 @@ }; &codec { + pinctrl-names = "default"; + pinctrl-0 = <&codec_pa_pin>; + allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */ status = "okay"; }; @@ -176,6 +179,13 @@ allwinner,pull = ; }; + codec_pa_pin: codec_pa_pin@0 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + ts_reset_pin: ts_reset_pin@0 { allwinner,pins = "PB13"; allwinner,function = "gpio_out"; -- cgit v1.2.3 From b0389c2cafc36ebf21df1a5189424658a26ac44e Mon Sep 17 00:00:00 2001 From: Marcus Cooper Date: Sat, 19 Dec 2015 14:02:38 +0100 Subject: ARM: sunxi: dt: enable audio codec on mk802 This commit enables the on-chip audio codec present on some variants of the MK802. Signed-off-by: Marcus Cooper Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-mk802.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun4i-a10-mk802.dts b/arch/arm/boot/dts/sun4i-a10-mk802.dts index 3c7eebe17088..ddf0683cbc6a 100644 --- a/arch/arm/boot/dts/sun4i-a10-mk802.dts +++ b/arch/arm/boot/dts/sun4i-a10-mk802.dts @@ -58,6 +58,10 @@ }; }; +&codec { + status = "okay"; +}; + &ehci0 { status = "okay"; }; -- cgit v1.2.3 From 8661d0c34e8ad044afa5a3cbf04c7e0e35f2e465 Mon Sep 17 00:00:00 2001 From: Marcus Cooper Date: Sat, 19 Dec 2015 14:08:46 +0100 Subject: ARM: dt: sun7i: Enable audio codec on MK808C This commit enables the on-chip audio codec present on the MK808C. Signed-off-by: Marcus Cooper Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-mk808c.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-mk808c.dts b/arch/arm/boot/dts/sun7i-a20-mk808c.dts index 4f432f8ade77..c9e648d17a1e 100644 --- a/arch/arm/boot/dts/sun7i-a20-mk808c.dts +++ b/arch/arm/boot/dts/sun7i-a20-mk808c.dts @@ -68,6 +68,10 @@ }; }; +&codec { + status = "okay"; +}; + &ehci0 { status = "okay"; }; -- cgit v1.2.3 From b3a9995e58dedc995ee9b6c16aed75839cb4ba94 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sun, 20 Dec 2015 12:43:02 +0100 Subject: ARM: dts: sun7i: Enable gmac on Wits Pro A20 DKT The Wits Pro A20 DKT has a gbit ethernet port, enable it. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts index 85b500d8cc4c..dc31d476ef81 100644 --- a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts +++ b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts @@ -80,6 +80,18 @@ status = "okay"; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; -- cgit v1.2.3 From 12ec9384036304e64904afdc6234b842fe54f411 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sun, 20 Dec 2015 12:43:01 +0100 Subject: ARM: dts: sun5i: Add dts file for the Empire Electronix D709 tablet The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet, featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack. Empire Electronix is written on the back of the tablet, the D709 model info can be found in the about tablet menu in android. The PCB has no markings to speak of. This dts file does not add support for the ft5x touchscreen found at i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box. It seems it has been flashed with the wrong firmware and needs to have alternative firmware uploaded at boot to make the touchscreen work properly, when hot-booting from android into an upstream kernel the touchscreen does work. The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not enabled as there is no driver for it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/sun5i-a13-empire-electronix-d709.dts | 241 +++++++++++++++++++++ 2 files changed, 242 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index cc7309be499f..da910b2d0c22 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -612,6 +612,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a10s-olinuxino-micro.dtb \ sun5i-a10s-r7-tv-dongle.dtb \ sun5i-a10s-wobo-i5.dtb \ + sun5i-a13-empire-electronix-d709.dtb \ sun5i-a13-hsg-h702.dtb \ sun5i-a13-inet-98v-rev2.dtb \ sun5i-a13-olinuxino.dtb \ diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts new file mode 100644 index 000000000000..7fbb0b0558a9 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts @@ -0,0 +1,241 @@ +/* + * Copyright 2015 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a13.dtsi" +#include "sunxi-common-regulators.dtsi" +#include +#include +#include +#include +#include + +/ { + model = "Empire Electronix D709 tablet"; + compatible = "empire-electronix,d709", "allwinner,sun5i-a13"; + + aliases { + serial0 = &uart1; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + /* TODO: backlight uses axp gpio1 as enable pin */ + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = ; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = ; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ + cd-inverted; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; + + mmccard: mmccard@0 { + reg = <0>; + compatible = "mmc-card"; + broken-hpi; + }; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 { + allwinner,pins = "PG0"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + status = "okay"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_usb0_vbus { + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_b>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG12"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_ldo3>; + status = "okay"; +}; -- cgit v1.2.3 From 6c95771f8c71cd4dd6ed7ab84a3aea7d509d7704 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 20 Dec 2015 09:26:15 -0600 Subject: ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support The development kit uses a TSC2004 chip attached to I2C3. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 27 +++++++++++++++++++++++ 1 file changed, 27 insertions(+) diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts index 6854bda5063f..fb13f18c08cc 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -204,6 +204,12 @@ >; }; + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; + backlight_pins: pinmux_backlight_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ @@ -262,6 +268,27 @@ }; }; +&i2c3 { + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + &uart1 { interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; }; -- cgit v1.2.3 From 70450d4d5869267ff0c1a12c1e376cc901fcc1fb Mon Sep 17 00:00:00 2001 From: Songjun Wu Date: Tue, 22 Dec 2015 17:26:04 +0800 Subject: ARM: at91/dt: sama5d2: add pdmic node Add pdmic node. Signed-off-by: Songjun Wu Signed-off-by: Alexandre Belloni --- arch/arm/boot/dts/sama5d2.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi index 545264b856b3..3f750f6170f2 100644 --- a/arch/arm/boot/dts/sama5d2.dtsi +++ b/arch/arm/boot/dts/sama5d2.dtsi @@ -637,6 +637,12 @@ atmel,clk-output-range = <0 83000000>; }; + pdmic_clk: pdmic_clk { + #clock-cells = <0>; + reg = <48>; + atmel,clk-output-range = <0 83000000>; + }; + i2s0_clk: i2s0_clk { #clock-cells = <0>; reg = <54>; @@ -763,6 +769,11 @@ atmel,clk-output-range = <0 83000000>; }; + pdmic_gclk: pdmic_gclk { + #clock-cells = <0>; + reg = <48>; + }; + i2s0_gclk: i2s0_gclk { #clock-cells = <0>; reg = <54>; @@ -852,6 +863,19 @@ clock-names = "t0_clk", "slow_clk"; }; + pdmic: pdmic@f8018000 { + compatible = "atmel,sama5d2-pdmic"; + reg = <0xf8018000 0x124>; + interrupts = <48 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(50))>; + dma-names = "rx"; + clocks = <&pdmic_clk>, <&pdmic_gclk>; + clock-names = "pclk", "gclk"; + status = "disabled"; + }; + uart0: serial@f801c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xf801c000 0x100>; -- cgit v1.2.3 From ca6349a8c51f2e3d6f2acdb36431e7d7328261f7 Mon Sep 17 00:00:00 2001 From: Songjun Wu Date: Tue, 22 Dec 2015 17:26:05 +0800 Subject: ARM: at91/dt: sama5d2 Xplained: add pdmic node Add pdmic node on sama5d2-xplained board.The pdmic pins conflict with ISC_D0 & ISC_D1 data pins. Signed-off-by: Songjun Wu Signed-off-by: Alexandre Belloni --- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 80fdab72f4fa..787a166b0393 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -119,6 +119,16 @@ status = "okay"; }; + pdmic@f8018000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pdmic_default>; + atmel,model = "PDMIC @ sama5d2_xplained"; + atmel,mic-min-freq = <1000000>; + atmel,mic-max-freq = <3246000>; + atmel,mic-offset = <0x0>; + status = "okay"; + }; + uart1: serial@f8020000 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1_default>; @@ -289,6 +299,12 @@ bias-disable; }; + pinctrl_pdmic_default: pdmic_default { + pinmux = , + ; + bias-disable; + }; + pinctrl_sdmmc0_default: sdmmc0_default { cmd_data { pinmux = , -- cgit v1.2.3 From 9493bf5458e936b88e5d3a33f9ed09bc5c1263b0 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Wed, 30 Sep 2015 10:17:16 +0800 Subject: ARM: dts: imx6: set ahb-burst-config as 0 for USB After setting ahb burst configuration as 0, we can increase tx/rx burst size, it will improve the USB performance Signed-off-by: Peter Chen Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl.dtsi | 4 ++++ arch/arm/boot/dts/imx6sl.dtsi | 3 +++ arch/arm/boot/dts/imx6sx.dtsi | 3 +++ arch/arm/boot/dts/imx6ul.dtsi | 2 ++ 4 files changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 2b6cc8bf3c5c..3234eb9aba94 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -906,6 +906,7 @@ clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -917,6 +918,7 @@ fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; dr_mode = "host"; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -927,6 +929,7 @@ clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; dr_mode = "host"; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -937,6 +940,7 @@ clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 3>; dr_mode = "host"; + ahb-burst-config = <0x0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index d8ba99f1d87b..3e8653a13fe0 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -708,6 +708,7 @@ clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -718,6 +719,7 @@ clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -728,6 +730,7 @@ clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; dr_mode = "host"; + ahb-burst-config = <0x0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index 167f77b3bd43..ea29e2e45875 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -783,6 +783,7 @@ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; fsl,anatop = <&anatop>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -793,6 +794,7 @@ clocks = <&clks IMX6SX_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -805,6 +807,7 @@ phy_type = "hsic"; fsl,anatop = <&anatop>; dr_mode = "host"; + ahb-burst-config = <0x0>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index d00e994bdbd2..9b83f767b324 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -548,6 +548,7 @@ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; fsl,anatop = <&anatop>; + ahb-burst-config = <0x0>; status = "disabled"; }; @@ -558,6 +559,7 @@ clocks = <&clks IMX6UL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; + ahb-burst-config = <0x0>; status = "disabled"; }; -- cgit v1.2.3 From 2b1a40e8d182a9f7779ba4fe54c5b73980c215b0 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Wed, 30 Sep 2015 10:17:17 +0800 Subject: ARM: dts: imx6: change default burst size for USB It can improve the USB performance when choosing larger burst size at some systems (bus size is larger), there is no side effect if this burst size is larger than bus size. Signed-off-by: Peter Chen Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl.dtsi | 8 ++++++++ arch/arm/boot/dts/imx6sl.dtsi | 6 ++++++ arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++ arch/arm/boot/dts/imx6ul.dtsi | 4 ++++ 4 files changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 3234eb9aba94..b98a41664855 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -907,6 +907,8 @@ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -919,6 +921,8 @@ fsl,usbmisc = <&usbmisc 1>; dr_mode = "host"; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -930,6 +934,8 @@ fsl,usbmisc = <&usbmisc 2>; dr_mode = "host"; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -941,6 +947,8 @@ fsl,usbmisc = <&usbmisc 3>; dr_mode = "host"; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 3e8653a13fe0..ebeae8f76436 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -709,6 +709,8 @@ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -720,6 +722,8 @@ fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -731,6 +735,8 @@ fsl,usbmisc = <&usbmisc 2>; dr_mode = "host"; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index ea29e2e45875..64608e2299f1 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -784,6 +784,8 @@ fsl,usbmisc = <&usbmisc 0>; fsl,anatop = <&anatop>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -795,6 +797,8 @@ fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -808,6 +812,8 @@ fsl,anatop = <&anatop>; dr_mode = "host"; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index 9b83f767b324..0e9716b79db8 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -549,6 +549,8 @@ fsl,usbmisc = <&usbmisc 0>; fsl,anatop = <&anatop>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; @@ -560,6 +562,8 @@ fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; status = "disabled"; }; -- cgit v1.2.3 From eb45ff74691bfec71af12b77215a9a33d521172a Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 3 Nov 2015 14:25:36 -0200 Subject: ARM: dts: imx6sx: Pass the 'adck-max-frequency' property Specify the 'adck-max-frequency' property in the adc nodes. According to Documentation/devicetree/bindings/iio/adc/vf610-adc.txt this is a recommended property. Signed-off-by: Fabio Estevam Acked-by: Fugang Duan Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6sx.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index 64608e2299f1..a74ae8d60c60 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -1161,6 +1161,8 @@ interrupts = ; clocks = <&clks IMX6SX_CLK_IPG>; clock-names = "adc"; + fsl,adck-max-frequency = <30000000>, <40000000>, + <20000000>; status = "disabled"; }; @@ -1170,6 +1172,8 @@ interrupts = ; clocks = <&clks IMX6SX_CLK_IPG>; clock-names = "adc"; + fsl,adck-max-frequency = <30000000>, <40000000>, + <20000000>; status = "disabled"; }; -- cgit v1.2.3 From aab8ec0c73cc0195a0b205003f2b9ed24177a6ac Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 4 Nov 2015 10:54:50 -0200 Subject: ARM: dts: imx6ul: Add ADC support Add support for ADC1. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index 0e9716b79db8..99b646506fc9 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -625,6 +625,18 @@ status = "disabled"; }; + adc1: adc@02198000 { + compatible = "fsl,imx6ul-adc", "fsl,vf610-adc"; + reg = <0x02198000 0x4000>; + interrupts = ; + clocks = <&clks IMX6UL_CLK_ADC1>; + num-channels = <2>; + clock-names = "adc"; + fsl,adck-max-frequency = <30000000>, <40000000>, + <20000000>; + status = "disabled"; + }; + i2c1: i2c@021a0000 { #address-cells = <1>; #size-cells = <0>; -- cgit v1.2.3 From b312e3600d8f02d9452fb9baa7b275d2d2587a8c Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Fri, 6 Nov 2015 11:44:29 +0100 Subject: ARM: dts: imx25-pinfunc: add some more pin configurations MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch adds some values that are needed for an out-of-tree device tree I'm currently working with. Signed-off-by: Uwe Kleine-König Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx25-pinfunc.h | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h index 7c4b9f2f9aad..848ffa785b63 100644 --- a/arch/arm/boot/dts/imx25-pinfunc.h +++ b/arch/arm/boot/dts/imx25-pinfunc.h @@ -284,6 +284,7 @@ #define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x11 0x000 #define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x14 0x000 #define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x15 0x001 +#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x16 0x000 #define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x10 0x000 #define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x15 0x000 @@ -439,6 +440,7 @@ #define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000 #define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x10 0x000 +#define MX25_PAD_KPP_ROW0__UART1_DTR 0x1a8 0x3a0 0x000 0x14 0x000 #define MX25_PAD_KPP_ROW0__GPIO_2_29 0x1a8 0x3a0 0x000 0x15 0x000 #define MX25_PAD_KPP_ROW1__KPP_ROW1 0x1ac 0x3a4 0x000 0x10 0x000 @@ -446,6 +448,7 @@ #define MX25_PAD_KPP_ROW2__KPP_ROW2 0x1b0 0x3a8 0x000 0x10 0x000 #define MX25_PAD_KPP_ROW2__CSI_D0 0x1b0 0x3a8 0x488 0x13 0x002 +#define MX25_PAD_KPP_ROW2__UART1_DCD 0x1b0 0x3a8 0x000 0x14 0x000 #define MX25_PAD_KPP_ROW2__GPIO_2_31 0x1b0 0x3a8 0x000 0x15 0x000 #define MX25_PAD_KPP_ROW3__KPP_ROW3 0x1b4 0x3ac 0x000 0x10 0x000 -- cgit v1.2.3 From 70b6b438cc365d8d269339986e63ceb943e8d423 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Fri, 6 Nov 2015 14:40:30 -0800 Subject: ARM: dts: imx: ventana: GW54xx PMIC swbst reg always-on The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver and HDMI DDC and is enabled by the bootloader. Set the regulator to always-on so that Linux doesn't turn it off thinking its not needed. Signed-off-by: Tim Harvey Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi index 6c11a2ae35ef..0c1682562b34 100644 --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -260,6 +260,8 @@ swbst_reg: swbst { regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5150000>; + regulator-boot-on; + regulator-always-on; }; snvs_reg: vsnvs { -- cgit v1.2.3 From a7668fda6b9987039e0dc0ea4e7262b019cce770 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Fri, 6 Nov 2015 14:40:31 -0800 Subject: ARM: dts: imx: ventana: fix GW53xx/GW54xx lvds channel Signed-off-by: Tim Harvey Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +- arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi index eea90f37bbb8..efef049c9a0b 100644 --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi @@ -247,7 +247,7 @@ &ldb { status = "okay"; - lvds-channel@1 { + lvds-channel@0 { fsl,data-mapping = "spwg"; fsl,data-width = <18>; status = "okay"; diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi index 0c1682562b34..fe71d36c1b66 100644 --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -338,7 +338,7 @@ &ldb { status = "okay"; - lvds-channel@1 { + lvds-channel@0 { fsl,data-mapping = "spwg"; fsl,data-width = <18>; status = "okay"; -- cgit v1.2.3 From e726a9fdde2863697f885a8bef8af38c3c759eb3 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Fri, 6 Nov 2015 14:40:32 -0800 Subject: ARM: dts: imx: ventana: Allow HDMI and LVDS to work simultaneously Currently it is not possible to have HDMI and LVDS working simultaneously, because both ports try to use PLL5. Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be driven from independent sources. With this change the LDB pixel clock goes to 68.57 MHz, which is still within the valid range for the displays supported by the Ventana boards. Signed-off-by: Tim Harvey Cc: Philipp Zabel Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 7 +++++++ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 7 +++++++ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 7 +++++++ 3 files changed, 21 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi index 18cd4114a23e..5478ab6b078e 100644 --- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi @@ -151,6 +151,13 @@ status = "okay"; }; +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi index efef049c9a0b..8ccf5e4f32ea 100644 --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi @@ -152,6 +152,13 @@ status = "okay"; }; +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi index fe71d36c1b66..7b50b1e55280 100644 --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -142,6 +142,13 @@ status = "okay"; }; +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; -- cgit v1.2.3 From c1b99dedfd5edd242c79b2ad6050bade11ae333f Mon Sep 17 00:00:00 2001 From: Markus Pargmann Date: Wed, 11 Nov 2015 07:46:05 +0100 Subject: ARM: dts: imx6dl: Fix gpt compatibles, remove imx6q-gpt imx6qdl.dtsi uses compatibles "fsl,imx6q-gpt", "fsl,imx31-gpt". imx6dl.dtsi uses compatibles "fsl,imx6dl-gpt", "fsl,imx6q-gpt" since commit 4e415ed8143f (ARM: dts: imx6dl: add imx6dl gpt specific compatible string) If imx6dl would be compatible with imx6q-gpt it would also have to be compatible with imx31-gpt which is currently missing. Based on the above mentioned patch I assume imx6q-gpt and imx6dl-gpt are not compatible. So imx6q-gpt should be removed as compatible. Signed-off-by: Markus Pargmann Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6dl.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi index 4b0ec0703825..e44ee075bdcc 100644 --- a/arch/arm/boot/dts/imx6dl.dtsi +++ b/arch/arm/boot/dts/imx6dl.dtsi @@ -107,7 +107,7 @@ }; &gpt { - compatible = "fsl,imx6dl-gpt", "fsl,imx6q-gpt"; + compatible = "fsl,imx6dl-gpt"; }; &hdmi { -- cgit v1.2.3 From 70f97128a158a596aeb82140ffacc8c18657baee Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 11 Nov 2015 14:32:44 +0100 Subject: ARM: dts: imx25: add alias for pwm nodes This, together with the corresponding patch to pwm-imx.c, allows to order the pwm devices correctly. Signed-off-by: Marc Kleine-Budde Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx25.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index 677f81d9dcd5..cde329e9b9e3 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -24,6 +24,10 @@ i2c2 = &i2c3; mmc0 = &esdhc1; mmc1 = &esdhc2; + pwm0 = &pwm1; + pwm1 = &pwm2; + pwm2 = &pwm3; + pwm3 = &pwm4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; -- cgit v1.2.3 From 5f060c71aa204c49efc8c3b93819a39c40e883c6 Mon Sep 17 00:00:00 2001 From: Cory Tusar Date: Wed, 18 Nov 2015 22:54:40 -0500 Subject: ARM: dts: vfxxx: Include support for dspi[23] functionality. Extend the existing Vybrid DSPI devicetree implementation to also describe the dspi2 and dspi3 functional blocks. Signed-off-by: Cory Tusar Acked-by: Stefan Agner Signed-off-by: Shawn Guo --- arch/arm/boot/dts/vfxxx.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index 3cd1b27f2697..a9ceb5bac40e 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -455,6 +455,30 @@ status = "disabled"; }; + dspi2: dspi2@400ac000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x400ac000 0x1000>; + interrupts = <69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_DSPI2>; + clock-names = "dspi"; + spi-num-chipselects = <2>; + status = "disabled"; + }; + + dspi3: dspi3@400ad000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x400ad000 0x1000>; + interrupts = <70 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_DSPI3>; + clock-names = "dspi"; + spi-num-chipselects = <2>; + status = "disabled"; + }; + adc1: adc@400bb000 { compatible = "fsl,vf610-adc"; reg = <0x400bb000 0x1000>; -- cgit v1.2.3 From 058c0c1a441e9518ae4de207997a9b43380528ce Mon Sep 17 00:00:00 2001 From: Afzal Mohammed Date: Sun, 25 Oct 2015 23:20:56 +0530 Subject: ARM: dts: vf6xx: Cosmic+: M4(nommu) initial support Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via Cortex-A5 running Linux using Stefan Agner's "m4boot" utility. Signed-off-by: Afzal Mohammed Acked-by: Stefan Agner Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/vf610m4-cosmic.dts | 90 ++++++++++++++++++++++++++++++++++++ 2 files changed, 91 insertions(+) create mode 100644 arch/arm/boot/dts/vf610m4-cosmic.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..9b00aa998dda 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -359,6 +359,7 @@ dtb-$(CONFIG_SOC_VF610) += \ vf610-colibri-eval-v3.dtb \ vf610m4-colibri.dtb \ vf610-cosmic.dtb \ + vf610m4-cosmic.dtb \ vf610-twr.dtb dtb-$(CONFIG_ARCH_MXS) += \ imx23-evk.dtb \ diff --git a/arch/arm/boot/dts/vf610m4-cosmic.dts b/arch/arm/boot/dts/vf610m4-cosmic.dts new file mode 100644 index 000000000000..8944a2d2054c --- /dev/null +++ b/arch/arm/boot/dts/vf610m4-cosmic.dts @@ -0,0 +1,90 @@ +/* + * Device tree for Cosmic+ VF6xx Cortex-M4 support + * + * Copyright (C) 2015 + * + * Based on vf610m4 Colibri + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "vf610m4.dtsi" + +/ { + model = "VF610 Cortex-M4"; + compatible = "fsl,vf610m4"; +}; + +&gpio0 { + status = "disabled"; +}; + +&gpio1 { + status = "disabled"; +}; + +&gpio2 { + status = "disabled"; +}; + +&gpio3 { + status = "disabled"; +}; + +&gpio4 { + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&iomuxc { + vf610-cosmic { + pinctrl_uart3: uart3grp { + fsl,pins = < + VF610_PAD_PTA20__UART3_TX 0x21a2 + VF610_PAD_PTA21__UART3_RX 0x21a1 + >; + }; + }; +}; -- cgit v1.2.3 From aa2b21783b1321e9d7f3ee92eb8e034f41447569 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Thu, 19 Nov 2015 12:02:03 -0800 Subject: ARM: dts: imx: ventana: add PWM nodes for Ventana boards Ventana boards have an off-board connector with signals that can be pinmuxed as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled state which the bootloader can decide to enable based on bootloader config. Signed-off-by: Tim Harvey Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 36 +++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 24 +++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 24 +++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 36 +++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 24 +++++++++++++++++++++++ arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 24 +++++++++++++++++++++++ 6 files changed, 168 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi index dc0cebfe22d7..5cd16f2178b8 100644 --- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi @@ -174,6 +174,24 @@ status = "okay"; }; +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */ + status = "disabled"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; @@ -294,6 +312,24 @@ >; }; + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1 + >; + }; + pinctrl_uart1: uart1grp { fsl,pins = < MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi index 5478ab6b078e..1a250f3b8457 100644 --- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi @@ -282,6 +282,18 @@ status = "okay"; }; +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + &pwm4 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm4>; @@ -436,6 +448,18 @@ >; }; + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + pinctrl_pwm4: pwm4grp { fsl,pins = < MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi index 8ccf5e4f32ea..e8375e173873 100644 --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi @@ -287,6 +287,18 @@ }; }; +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + &pwm4 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm4>; @@ -442,6 +454,18 @@ >; }; + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + pinctrl_pwm4: pwm4grp { fsl,pins = < MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi index 7b50b1e55280..66983dc5cbda 100644 --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -378,6 +378,24 @@ }; }; +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */ + status = "disabled"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + &pwm4 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm4>; @@ -537,6 +555,24 @@ >; }; + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + pinctrl_pwm4: pwm4grp { fsl,pins = < MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi index 741f3d529e3e..118bea524dab 100644 --- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi @@ -198,6 +198,18 @@ status = "okay"; }; +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + &ssi1 { status = "okay"; }; @@ -290,6 +302,18 @@ >; }; + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + pinctrl_uart2: uart2grp { fsl,pins = < MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi index d1e5048b00b5..cca39f194017 100644 --- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi @@ -164,6 +164,18 @@ status = "okay"; }; +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ + status = "disabled"; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; @@ -242,6 +254,18 @@ >; }; + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + pinctrl_uart2: uart2grp { fsl,pins = < MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 -- cgit v1.2.3 From 3edf253c5de97861493325d1b1c2db04e39cfa77 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Thu, 19 Nov 2015 12:02:24 -0800 Subject: ARM: dts: imx: ventana: Add SPI support for GW52xx This addes support for SPI available on an off-board connector available on some models of the GW52xx. Signed-off-by: Tim Harvey Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi index 1a250f3b8457..9fa8a10c7cc8 100644 --- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi @@ -158,6 +158,14 @@ <&clks IMX6QDL_CLK_PLL3_USB_OTG>; }; +&ecspi3 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + status = "okay"; +}; + &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; @@ -357,6 +365,15 @@ >; }; + pinctrl_ecspi3: escpi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x100b1 + >; + }; + pinctrl_enet: enetgrp { fsl,pins = < MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 -- cgit v1.2.3 From 698e2ac5361f6fd7588afdd86becbfae0084e98a Mon Sep 17 00:00:00 2001 From: Bai Ping Date: Tue, 24 Nov 2015 18:25:15 +0800 Subject: ARM: dts: imx: modify the clocks used by cpufreq driver As on i.MX7D, we using a virtual arm clk for CPU frequency scaling, so correct the clocks info used by the cpufreq driver. Signed-off-by: Bai Ping Acked-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx7d.dtsi | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi index ebc053a06405..489604a9ba91 100644 --- a/arch/arm/boot/dts/imx7d.dtsi +++ b/arch/arm/boot/dts/imx7d.dtsi @@ -85,9 +85,7 @@ 792000 975000 >; clock-latency = <61036>; /* two CLK32 periods */ - clocks = <&clks IMX7D_ARM_A7_ROOT_CLK>, <&clks IMX7D_ARM_A7_ROOT_SRC>, - <&clks IMX7D_PLL_ARM_MAIN_CLK>, <&clks IMX7D_PLL_SYS_MAIN_CLK>; - clock-names = "arm", "arm_root_src", "pll_arm", "pll_sys_main"; + clocks = <&clks IMX7D_CLK_ARM>; }; cpu1: cpu@1 { -- cgit v1.2.3 From ab0087dfc29d5dad022c4f2831c63eb4b73e3210 Mon Sep 17 00:00:00 2001 From: Meng Yi Date: Wed, 25 Nov 2015 14:46:06 +0800 Subject: ARM: dts: ls1021a: Add DCU dts node. Signed-off-by: Alison Wang Signed-off-by: Xiubo Li Signed-off-by: Jianwei Wang Signed-off-by: Meng Yi Signed-off-by: Shawn Guo --- arch/arm/boot/dts/ls1021a.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index 9430a9928199..f01c98b37f96 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -428,6 +428,16 @@ <&platform_clk 1>; }; + dcu: dcu@2ce0000 { + compatible = "fsl,ls1021a-dcu"; + reg = <0x0 0x2ce0000 0x0 0x10000>; + interrupts = ; + clocks = <&platform_clk 0>; + clock-names = "dcu"; + big-endian; + status = "disabled"; + }; + mdio0: mdio@2d24000 { compatible = "gianfar"; device_type = "mdio"; -- cgit v1.2.3 From edb3ed394bf4ac947d83397480b6262b9f2ff326 Mon Sep 17 00:00:00 2001 From: Meng Yi Date: Wed, 25 Nov 2015 14:46:07 +0800 Subject: ARM: dts: ls1021a: Add a TFT LCD panel. Signed-off-by: Alison Wang Signed-off-by: Xiubo Li Signed-off-by: Jianwei Wang Signed-off-by: Meng Yi Signed-off-by: Shawn Guo --- arch/arm/boot/dts/ls1021a-twr.dts | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts index fbb89d13401e..28173b1f6800 100644 --- a/arch/arm/boot/dts/ls1021a-twr.dts +++ b/arch/arm/boot/dts/ls1021a-twr.dts @@ -105,6 +105,15 @@ bitclock-master; }; }; + + panel: panel { + compatible = "nec,nl4827hc19-05b"; + }; +}; + +&dcu { + fsl,panel = <&panel>; + status = "okay"; }; &dspi1 { -- cgit v1.2.3 From 09d3059adcaf29cd3c3810a083474e7c9d087905 Mon Sep 17 00:00:00 2001 From: Shengjiu Wang Date: Thu, 26 Nov 2015 10:39:30 +0800 Subject: ARM: dts: imx6: Change the clock name for spba clock Audio IP need the spba clock, but original clock name "dma" is not accurate, so change it to name "spba". The audio driver has been using the new name "spba", the binding document has been updated. Signed-off-by: Shengjiu Wang Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl.dtsi | 6 +++--- arch/arm/boot/dts/imx6sl.dtsi | 2 +- arch/arm/boot/dts/imx6sx.dtsi | 6 +++--- 3 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index b98a41664855..f3b005c0a766 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -227,7 +227,7 @@ "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", - "rxtx7", "dma"; + "rxtx7", "spba"; status = "disabled"; }; @@ -309,7 +309,7 @@ <&clks IMX6QDL_CLK_ESAI_EXTAL>, <&clks IMX6QDL_CLK_ESAI_IPG>, <&clks IMX6QDL_CLK_SPBA>; - clock-names = "core", "mem", "extal", "fsys", "dma"; + clock-names = "core", "mem", "extal", "fsys", "spba"; dmas = <&sdma 23 21 0>, <&sdma 24 21 0>; dma-names = "rx", "tx"; status = "disabled"; @@ -378,7 +378,7 @@ "asrck_1", "asrck_2", "asrck_3", "asrck_4", "asrck_5", "asrck_6", "asrck_7", "asrck_8", "asrck_9", "asrck_a", "asrck_b", "asrck_c", - "asrck_d", "asrck_e", "asrck_f", "dma"; + "asrck_d", "asrck_e", "asrck_f", "spba"; dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>, <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>; dma-names = "rxa", "rxb", "rxc", diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index ebeae8f76436..d12b250342a6 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -151,7 +151,7 @@ "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", - "rxtx7", "dma"; + "rxtx7", "spba"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index a74ae8d60c60..a5f76025a0ce 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -222,7 +222,7 @@ "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", - "rxtx7", "dma"; + "rxtx7", "spba"; status = "disabled"; }; @@ -295,7 +295,7 @@ <&clks IMX6SX_CLK_ESAI_IPG>, <&clks IMX6SX_CLK_SPBA>; clock-names = "core", "mem", "extal", - "fsys", "dma"; + "fsys", "spba"; status = "disabled"; }; @@ -348,7 +348,7 @@ <&clks IMX6SX_CLK_ASRC_IPG>, <&clks IMX6SX_CLK_SPDIF>, <&clks IMX6SX_CLK_SPBA>; - clock-names = "mem", "ipg", "asrck", "dma"; + clock-names = "mem", "ipg", "asrck", "spba"; dmas = <&sdma 17 20 1>, <&sdma 18 20 1>, <&sdma 19 20 1>, <&sdma 20 20 1>, <&sdma 21 20 1>, <&sdma 22 20 1>; -- cgit v1.2.3 From d9cf0a125ed026a86f0eb256b60a17e682604522 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 30 Nov 2015 18:00:10 +0100 Subject: ARM: dts: imx6: remove config space from PCIe controller ranges property This has been moved to the reg property where it belongs for quite some time. The range has been unused by the kernel since then and with kernel 4.4 it's flagged as an unparsable range, as it does not comply to the PCI ranges DT binding. Fix this by removing the superfluous range. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index f3b005c0a766..de6d17502512 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -173,8 +173,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */ - 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ + ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ num-lanes = <1>; interrupts = ; -- cgit v1.2.3 From 41beef39cdc8f282844b001efb9e83363ccfdcc3 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Wed, 2 Dec 2015 14:42:22 +0100 Subject: ARM: dts: imx6qdl: add IPU aliases This allows for consistent numbering of the IPU output and input ports. Signed-off-by: Philipp Zabel Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6q.dtsi | 1 + arch/arm/boot/dts/imx6qdl.dtsi | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 399103b8e2c9..a266a564a3f6 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -14,6 +14,7 @@ / { aliases { + ipu1 = &ipu2; spi4 = &ecspi5; }; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index de6d17502512..ec64bcc9cb64 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -30,6 +30,7 @@ i2c0 = &i2c1; i2c1 = &i2c2; i2c2 = &i2c3; + ipu0 = &ipu1; mmc0 = &usdhc1; mmc1 = &usdhc2; mmc2 = &usdhc3; -- cgit v1.2.3 From 67157882a4eb9375a8fdf6948de2c61e0596a545 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Wed, 2 Dec 2015 14:42:55 +0100 Subject: ARM: dts: imx6qdl: move GIC to right location in DT No functional change, just moving the node to the place where it belongs according to its unit address. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl.dtsi | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index ec64bcc9cb64..41ba2d9c17a2 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -48,15 +48,6 @@ usbphy1 = &usbphy2; }; - intc: interrupt-controller@00a01000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x00a01000 0x1000>, - <0x00a00100 0x100>; - interrupt-parent = <&intc>; - }; - clocks { #address-cells = <1>; #size-cells = <0>; @@ -156,6 +147,15 @@ clocks = <&clks IMX6QDL_CLK_TWD>; }; + intc: interrupt-controller@00a01000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x00a01000 0x1000>, + <0x00a00100 0x100>; + interrupt-parent = <&intc>; + }; + L2: l2-cache@00a02000 { compatible = "arm,pl310-cache"; reg = <0x00a02000 0x1000>; -- cgit v1.2.3 From 234f82a70244f36f770b6f8567c51ba231b6bfcc Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Wed, 2 Dec 2015 22:35:22 +0100 Subject: ARM: mxs: dt: cfa10057: fix backlight PWM The backlight PWM is actually pwm4. Signed-off-by: Alexandre Belloni Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-cfa10057.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts index 5df0b24eaf59..7a80bd686c40 100644 --- a/arch/arm/boot/dts/imx28-cfa10057.dts +++ b/arch/arm/boot/dts/imx28-cfa10057.dts @@ -115,7 +115,7 @@ pwm: pwm@80064000 { pinctrl-names = "default"; - pinctrl-0 = <&pwm3_pins_b>; + pinctrl-0 = <&pwm4_pins_a>; status = "okay"; }; @@ -170,7 +170,7 @@ backlight { compatible = "pwm-backlight"; - pwms = <&pwm 3 5000000>; + pwms = <&pwm 4 5000000>; brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <7>; }; -- cgit v1.2.3 From 2afa06cbf11ab6c2ca2d937ce712e4f40e58f7a3 Mon Sep 17 00:00:00 2001 From: Stefan Agner Date: Wed, 2 Dec 2015 14:11:47 -0800 Subject: ARM: dts: vf-colibri: add CAN support Add Colibri standard pinmux for FlexCAN controller instances. CAN is not a standard Colibri feature, but the datasheet predefines pins which provide CAN (compatible across some modules). Hence, add the pinmux on module level. Signed-off-by: Stefan Agner Signed-off-by: Shawn Guo --- arch/arm/boot/dts/vf-colibri.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index e5949b934945..6e556be42ccd 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -23,6 +23,18 @@ status = "okay"; }; +&can0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan0>; + status = "disabled"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "disabled"; +}; + &dspi1 { bus-num = <1>; pinctrl-names = "default"; @@ -125,6 +137,20 @@ &iomuxc { vf610-colibri { + pinctrl_flexcan0: can0grp { + fsl,pins = < + VF610_PAD_PTB14__CAN0_RX 0x31F1 + VF610_PAD_PTB15__CAN0_TX 0x31F2 + >; + }; + + pinctrl_flexcan1: can1grp { + fsl,pins = < + VF610_PAD_PTB16__CAN1_RX 0x31F1 + VF610_PAD_PTB17__CAN1_TX 0x31F2 + >; + }; + pinctrl_gpio_ext: gpio_ext { fsl,pins = < VF610_PAD_PTD10__GPIO_89 0x22ed /* EXT_IO_0 */ -- cgit v1.2.3 From a3d19f2179e3e681341f03569d437bcc183129b2 Mon Sep 17 00:00:00 2001 From: Haibo Chen Date: Tue, 8 Dec 2015 18:26:22 +0800 Subject: ARM: dts: imx7d.dtsi: add ADC support Add imx7d ADC support. Signed-off-by: Haibo Chen Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx7d.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi index 489604a9ba91..25ad30978740 100644 --- a/arch/arm/boot/dts/imx7d.dtsi +++ b/arch/arm/boot/dts/imx7d.dtsi @@ -581,6 +581,24 @@ reg = <0x30400000 0x400000>; ranges; + adc1: adc@30610000 { + compatible = "fsl,imx7d-adc"; + reg = <0x30610000 0x10000>; + interrupts = ; + clocks = <&clks IMX7D_ADC_ROOT_CLK>; + clock-names = "adc"; + status = "disabled"; + }; + + adc2: adc@30620000 { + compatible = "fsl,imx7d-adc"; + reg = <0x30620000 0x10000>; + interrupts = ; + clocks = <&clks IMX7D_ADC_ROOT_CLK>; + clock-names = "adc"; + status = "disabled"; + }; + pwm1: pwm@30660000 { compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; reg = <0x30660000 0x10000>; -- cgit v1.2.3 From 64b834324df7597cb9b44abe415d7b7dfd82ee0b Mon Sep 17 00:00:00 2001 From: Haibo Chen Date: Tue, 8 Dec 2015 18:26:23 +0800 Subject: ARM: dts: imx7d-sdb: add ADC support Add ADC support for imx7d-sdb board. Signed-off-by: Haibo Chen Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx7d-sdb.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts index 432aaf5d5ef7..b2c453662905 100644 --- a/arch/arm/boot/dts/imx7d-sdb.dts +++ b/arch/arm/boot/dts/imx7d-sdb.dts @@ -97,6 +97,16 @@ }; }; +&adc1 { + vref-supply = <®_vref_1v8>; + status = "okay"; +}; + +&adc2 { + vref-supply = <®_vref_1v8>; + status = "okay"; +}; + &cpu0 { arm-supply = <&sw1a_reg>; }; -- cgit v1.2.3 From 328c9d7e532801dcaad5569364fe399b4eb52200 Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Fri, 11 Dec 2015 12:08:12 -0500 Subject: of: add vendor prefix for Technologic Systems Signed-off-by: Damien Riegel Acked-by: Lee Jones Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 55df1d444e9f..4df119886ed9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -223,6 +223,7 @@ stericsson ST-Ericsson synology Synology, Inc. tbs TBS Technologies tcl Toby Churchill Ltd. +technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility -- cgit v1.2.3 From 7ee70f23e9f8f974914b0c6e16bf79882df560c8 Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Fri, 11 Dec 2015 12:08:13 -0500 Subject: of: documentation: add bindings documentation for TS-4800 This adds the documentation for the TS-4800 by Technologic Systems. Signed-off-by: Damien Riegel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/technologic.txt | 6 ++++++ 1 file changed, 6 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/technologic.txt diff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt new file mode 100644 index 000000000000..842298894cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/technologic.txt @@ -0,0 +1,6 @@ +Technologic Systems Platforms Device Tree Bindings +-------------------------------------------------- + +TS-4800 board +Required root node properties: + - compatible = "technologic,imx51-ts4800", "fsl,imx51"; -- cgit v1.2.3 From b446ff229e1d760ef72ca20273d19dd786d0dacb Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Fri, 11 Dec 2015 12:08:14 -0500 Subject: ARM: dts: TS-4800: add basic device tree This device tree adds support for TS-4800 by Technologic Systems. This board is based on MX51-babbage, but there are some subtle differences in the pins used, and there is an additional FPGA that is memory-mapped. More details here: http://wiki.embeddedarm.com/wiki/TS-4800 Signed-off-by: Damien Riegel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/imx51-ts4800.dts | 180 +++++++++++++++++++++++++++++++++++++ 2 files changed, 182 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx51-ts4800.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 9b00aa998dda..ad3e25dfdec7 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -268,7 +268,8 @@ dtb-$(CONFIG_SOC_IMX51) += \ imx51-apf51dev.dtb \ imx51-babbage.dtb \ imx51-digi-connectcore-jsk.dtb \ - imx51-eukrea-mbimxsd51-baseboard.dtb + imx51-eukrea-mbimxsd51-baseboard.dtb \ + imx51-ts4800.dtb dtb-$(CONFIG_SOC_IMX53) += \ imx53-ard.dtb \ imx53-m53evk.dtb \ diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts new file mode 100644 index 000000000000..f1317f75365a --- /dev/null +++ b/arch/arm/boot/dts/imx51-ts4800.dts @@ -0,0 +1,180 @@ +/* + * Copyright 2015 Savoir-faire Linux + * + * This device tree is based on imx51-babbage.dts + * + * Licensed under the X11 license or the GPL v2 (or later) + */ + +/dts-v1/; +#include "imx51.dtsi" + +/ { + model = "Technologic Systems TS-4800"; + compatible = "technologic,imx51-ts4800", "fsl,imx51"; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x90000000 0x10000000>; + }; + + soc { + fpga { + compatible = "simple-bus"; + reg = <0xb0000000 0x1d000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon: syscon@b0010000 { + compatible = "syscon", "simple-mfd"; + reg = <0xb0010000 0x3d>; + reg-io-width = <2>; + + wdt@e { + compatible = "technologic,ts4800-wdt"; + syscon = <&syscon 0xe>; + }; + }; + }; + }; + + clocks { + ckih1 { + clock-frequency = <22579200>; + }; + + ckih2 { + clock-frequency = <24576000>; + }; + }; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; + phy-reset-duration = <1>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + rtc: m41t00@68 { + compatible = "stm,m41t00"; + reg = <0x68>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185 + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185 + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185 + MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */ + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 + MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + MX51_PAD_GPIO1_0__GPIO1_0 0x100 + MX51_PAD_GPIO1_1__GPIO1_1 0x100 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX51_PAD_EIM_EB2__FEC_MDIO 0x000001f5 + MX51_PAD_EIM_EB3__FEC_RDATA1 0x00000085 + MX51_PAD_EIM_CS2__FEC_RDATA2 0x00000085 + MX51_PAD_EIM_CS3__FEC_RDATA3 0x00000085 + MX51_PAD_EIM_CS4__FEC_RX_ER 0x00000180 + MX51_PAD_EIM_CS5__FEC_CRS 0x00000180 + MX51_PAD_DISP2_DAT10__FEC_COL 0x00000180 + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x00000180 + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x00002180 + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x00002004 + MX51_PAD_NANDF_CS2__FEC_TX_ER 0x00002004 + MX51_PAD_DI2_PIN2__FEC_MDC 0x00002004 + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x00002004 + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x00002004 + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x00002004 + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x00002004 + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x00002180 + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x000020a4 + MX51_PAD_EIM_A20__GPIO2_14 0x00000085 /* Phy Reset */ + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed + MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 + MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX51_PAD_UART2_RXD__UART2_RXD 0x1c5 + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX51_PAD_EIM_D25__UART3_RXD 0x1c5 + MX51_PAD_EIM_D26__UART3_TXD 0x1c5 + MX51_PAD_EIM_D27__UART3_RTS 0x1c5 + MX51_PAD_EIM_D24__UART3_CTS 0x1c5 + >; + }; +}; -- cgit v1.2.3 From 318f05e5d7e508d95192ad840bb0c5b266d232ce Mon Sep 17 00:00:00 2001 From: Tang Yuantian Date: Tue, 15 Dec 2015 15:14:14 +0800 Subject: ARM: dts: ls1021a: add sata node to dts Added sata node to ls1021aqds and ls1021atwr board to support sata function. Signed-off-by: Tang Yuantian Signed-off-by: Shawn Guo --- arch/arm/boot/dts/ls1021a-qds.dts | 4 ++++ arch/arm/boot/dts/ls1021a-twr.dts | 4 ++++ arch/arm/boot/dts/ls1021a.dtsi | 11 +++++++++++ 3 files changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a-qds.dts b/arch/arm/boot/dts/ls1021a-qds.dts index 0521e6864cb7..940875316d0f 100644 --- a/arch/arm/boot/dts/ls1021a-qds.dts +++ b/arch/arm/boot/dts/ls1021a-qds.dts @@ -320,6 +320,10 @@ status = "okay"; }; +&sata { + status = "okay"; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts index 28173b1f6800..75ecaed32ae5 100644 --- a/arch/arm/boot/dts/ls1021a-twr.dts +++ b/arch/arm/boot/dts/ls1021a-twr.dts @@ -221,6 +221,10 @@ status = "okay"; }; +&sata { + status = "okay"; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index f01c98b37f96..2c84ca236473 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -143,6 +143,17 @@ status = "disabled"; }; + sata: sata@3200000 { + compatible = "fsl,ls1021a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20220520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; + interrupts = ; + clocks = <&platform_clk 1>; + dma-coherent; + status = "disabled"; + }; + scfg: scfg@1570000 { compatible = "fsl,ls1021a-scfg", "syscon"; reg = <0x0 0x1570000 0x0 0x10000>; -- cgit v1.2.3 From cfa1dd99d50198e40fae6a370508f75927a350f1 Mon Sep 17 00:00:00 2001 From: Mans Rullgard Date: Fri, 11 Dec 2015 13:36:26 +0000 Subject: ARM: dts: imx28: add alternate auart4 pinmux Add auart4 2-pin configuration on auart0 rts/cts pads. Signed-off-by: Mans Rullgard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index c5b57d4adade..fae7b9069fc4 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -405,6 +405,17 @@ fsl,pull-up = ; }; + auart4_2pins_b: auart4@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_CTS__AUART4_RX + MX28_PAD_AUART0_RTS__AUART4_TX + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + mac0_pins_a: mac0@0 { reg = <0>; fsl,pinmux-ids = < -- cgit v1.2.3 From 419e202b260ba5913affd7cb3c36f129c036e8f7 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Tue, 15 Dec 2015 17:30:09 +0100 Subject: ARM: dts: imx6: add Vivante GPU nodes This adds the device nodes for 2D, 3D and VG GPU cores. Signed-off-by: Russell King Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6dl.dtsi | 5 +++++ arch/arm/boot/dts/imx6q.dtsi | 15 +++++++++++++++ arch/arm/boot/dts/imx6qdl.dtsi | 21 +++++++++++++++++++++ 3 files changed, 41 insertions(+) diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi index e44ee075bdcc..c13a73aa55ca 100644 --- a/arch/arm/boot/dts/imx6dl.dtsi +++ b/arch/arm/boot/dts/imx6dl.dtsi @@ -104,6 +104,11 @@ compatible = "fsl,imx-display-subsystem"; ports = <&ipu1_di0>, <&ipu1_di1>; }; + + gpu-subsystem { + compatible = "fsl,imx-gpu-subsystem"; + cores = <&gpu_2d>, <&gpu_3d>; + }; }; &gpt { diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index a266a564a3f6..9b6a193b64ca 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -154,6 +154,16 @@ status = "disabled"; }; + gpu_vg: gpu@02204000 { + compatible = "vivante,gc"; + reg = <0x02204000 0x4000>; + interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_OPENVG_AXI>, + <&clks IMX6QDL_CLK_GPU2D_CORE>; + clock-names = "bus", "core"; + power-domains = <&gpc 1>; + }; + ipu2: ipu@02800000 { #address-cells = <1>; #size-cells = <0>; @@ -226,6 +236,11 @@ compatible = "fsl,imx-display-subsystem"; ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>; }; + + gpu-subsystem { + compatible = "fsl,imx-gpu-subsystem"; + cores = <&gpu_2d>, <&gpu_3d>, <&gpu_vg>; + }; }; &hdmi { diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 41ba2d9c17a2..4f6ae921656f 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -139,6 +139,27 @@ }; }; + gpu_3d: gpu@00130000 { + compatible = "vivante,gc"; + reg = <0x00130000 0x4000>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_GPU3D_AXI>, + <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>; + clock-names = "bus", "core", "shader"; + power-domains = <&gpc 1>; + }; + + gpu_2d: gpu@00134000 { + compatible = "vivante,gc"; + reg = <0x00134000 0x4000>; + interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_GPU2D_AXI>, + <&clks IMX6QDL_CLK_GPU2D_CORE>; + clock-names = "bus", "core"; + power-domains = <&gpc 1>; + }; + timer@00a00600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; -- cgit v1.2.3 From 6989cc8fc7c161c661230a5dc80a690edbb28ab5 Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Thu, 17 Dec 2015 16:16:52 -0500 Subject: ARM: dts: TS-4800: drop uart rts/cts pin reservations These pins are actually not routed for UARTs, they should not be reserved. Signed-off-by: Damien Riegel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-ts4800.dts | 4 ---- 1 file changed, 4 deletions(-) diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts index f1317f75365a..64ac55cca57e 100644 --- a/arch/arm/boot/dts/imx51-ts4800.dts +++ b/arch/arm/boot/dts/imx51-ts4800.dts @@ -157,8 +157,6 @@ fsl,pins = < MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 - MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 - MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 >; }; @@ -173,8 +171,6 @@ fsl,pins = < MX51_PAD_EIM_D25__UART3_RXD 0x1c5 MX51_PAD_EIM_D26__UART3_TXD 0x1c5 - MX51_PAD_EIM_D27__UART3_RTS 0x1c5 - MX51_PAD_EIM_D24__UART3_CTS 0x1c5 >; }; }; -- cgit v1.2.3 From ef41e4c56f6534cdba024769b3fd3421dd34070d Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Thu, 17 Dec 2015 16:16:53 -0500 Subject: ARM: dts: TS-4800: use weim IP to map the FPGA Previously, the device tree mapped the FPGA like any other IPs inside the SoC, but it is actually mapped through the WEIM (Wireless External Interface Module). This patch updates the device tree to make use of it. About the timings: in the image provided by the manufacturer, only CS0GCR1 is changed. The other values are the default ones, but the WEIM bindings expect them to be all explicitly set in the device tree, so I just put the default values in the dt. Signed-off-by: Damien Riegel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-ts4800.dts | 60 +++++++++++++++++++++++++------------- 1 file changed, 39 insertions(+), 21 deletions(-) diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts index 64ac55cca57e..83352cb3f2d3 100644 --- a/arch/arm/boot/dts/imx51-ts4800.dts +++ b/arch/arm/boot/dts/imx51-ts4800.dts @@ -21,27 +21,6 @@ reg = <0x90000000 0x10000000>; }; - soc { - fpga { - compatible = "simple-bus"; - reg = <0xb0000000 0x1d000>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - syscon: syscon@b0010000 { - compatible = "syscon", "simple-mfd"; - reg = <0xb0010000 0x3d>; - reg-io-width = <2>; - - wdt@e { - compatible = "technologic,ts4800-wdt"; - syscon = <&syscon 0xe>; - }; - }; - }; - }; - clocks { ckih1 { clock-frequency = <22579200>; @@ -99,6 +78,33 @@ status = "okay"; }; +&weim { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_weim>; + status = "okay"; + + fpga@0 { + compatible = "simple-bus"; + fsl,weim-cs-timing = <0x0061008F 0x00000002 0x1c022000 + 0x00000000 0x1c092480 0x00000000>; + reg = <0 0x0000000 0x1d000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0x1d000>; + + syscon: syscon@b0010000 { + compatible = "syscon", "simple-mfd"; + reg = <0x10000 0x3d>; + reg-io-width = <2>; + + wdt@e { + compatible = "technologic,ts4800-wdt"; + syscon = <&syscon 0xe>; + }; + }; + }; +}; + &iomuxc { pinctrl_ecspi1: ecspi1grp { fsl,pins = < @@ -173,4 +179,16 @@ MX51_PAD_EIM_D26__UART3_TXD 0x1c5 >; }; + + pinctrl_weim: weimgrp { + fsl,pins = < + MX51_PAD_EIM_DTACK__EIM_DTACK 0x85 + MX51_PAD_EIM_CS0__EIM_CS0 0x0 + MX51_PAD_EIM_CS1__EIM_CS1 0x0 + MX51_PAD_EIM_EB0__EIM_EB0 0x85 + MX51_PAD_EIM_EB1__EIM_EB1 0x85 + MX51_PAD_EIM_OE__EIM_OE 0x85 + MX51_PAD_EIM_LBA__EIM_LBA 0x85 + >; + }; }; -- cgit v1.2.3 From 577bc8fbdb3a8c93a6b45663299d08637bb7bfe7 Mon Sep 17 00:00:00 2001 From: Sean Cross Date: Mon, 21 Dec 2015 21:07:47 +0800 Subject: devicetree: bindings: Add vendor prefix for Kosagi Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the more common name of Kosagi. Signed-off-by: Sean Cross Signed-off-by: Marek Vasut Cc: Rob Herring Cc: Fabio Estevam Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4df119886ed9..7db6f92bd05b 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -123,6 +123,7 @@ jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies +kosagi Sutajio Ko-Usagi PTE Ltd. lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. -- cgit v1.2.3 From 70a8c03bd9eea54fcd2616302403b80c20729db9 Mon Sep 17 00:00:00 2001 From: Sean Cross Date: Fri, 18 Dec 2015 06:29:50 +0100 Subject: ARM: dts: imx6q: add Novena board Novena is an open-hardware laptop/desktop/bare board. See http://www.kosagi.com/w/index.php?title=Novena_Main_Page Signed-off-by: Sean Cross Signed-off-by: Marek Vasut Cc: Lucas Stach Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-novena.dts | 785 +++++++++++++++++++++++++++++++++++++ 2 files changed, 786 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-novena.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ad3e25dfdec7..f0573a8dd6d2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ imx6q-nitrogen6_max.dtb \ + imx6q-novena.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ imx6q-sabreauto.dtb \ diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts new file mode 100644 index 000000000000..5acd0c63b33b --- /dev/null +++ b/arch/arm/boot/dts/imx6q-novena.dts @@ -0,0 +1,785 @@ +/* + * Copyright 2015 Sutajio Ko-Usagi PTE LTD + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include +#include + +/ { + model = "Kosagi Novena Dual/Quad"; + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; + + chosen { + stdout-path = &uart2; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 10000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight_novena>; + power-supply = <®_lvds_lcd>; + brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>; + default-brightness-level = <12>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys_novena>; + + user-button { + label = "User Button"; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + lid { + label = "Lid"; + gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_novena>; + + heartbeat { + label = "novena:white:panel"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + panel: panel { + compatible = "innolux,n133hse-ea1", "simple-panel"; + backlight = <&backlight>; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_audio_codec: regulator-audio-codec { + compatible = "regulator-fixed"; + regulator-name = "es8328-power"; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <400000>; + gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_display: regulator-display { + compatible = "regulator-fixed"; + regulator-name = "lcd-display-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <200000>; + gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_lvds_lcd: regulator-lvds-lcd { + compatible = "regulator-fixed"; + regulator-name = "lcd-lvds-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_pcie: regulator-pcie { + compatible = "regulator-fixed"; + regulator-name = "pcie-bus-power"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_sata: regulator-sata { + compatible = "regulator-fixed"; + regulator-name = "sata-power"; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <10000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; + + sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-amp-supply = <®_audio_codec>; + jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1", + "LINPUT1", "Mic Jack", + "RINPUT1", "Mic Jack", + "Mic Jack", "Mic Bias"; + mux-int-port = <0x1>; + mux-ext-port = <0x3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux_novena>; + status = "okay"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3_novena>; + fsl,spi-num-chipselects = <3>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_novena>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <3000>; + txd1-skew-ps = <3000>; + txd2-skew-ps = <3000>; + txd3-skew-ps = <3000>; + status = "okay"; +}; + +&hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hdmi_novena>; + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_novena>; + status = "okay"; + + accel: mma8452@1c { + compatible = "fsl,mma8452"; + reg = <0x1c>; + }; + + rtc: pcf8523@68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; + + sbs_battery: bq20z75@0b { + compatible = "sbs,sbs-battery"; + reg = <0x0b>; + sbs,i2c-retry-count = <50>; + }; + + touch: stmpe811@44 { + compatible = "st,stmpe811"; + reg = <0x44>; + #address-cells = <1>; + #size-cells = <0>; + irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe_novena>; + vio-supply = <®_3p3v>; + vcc-supply = <®_3p3v>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_novena>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + reg_sw1a: sw1a { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + reg_sw1c: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw2: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw3a: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw3b: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw4: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + reg_swbst: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + regulator-boot-on; + }; + + reg_snvs: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vref: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + reg_vgen1: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + reg_vgen2: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + reg_vgen3: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + reg_vgen4: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vgen5: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vgen6: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_novena>; + status = "okay"; + + codec: es8328@11 { + compatible = "everest,es8328"; + reg = <0x11>; + DVDD-supply = <®_audio_codec>; + AVDD-supply = <®_audio_codec>; + PVDD-supply = <®_audio_codec>; + HPVDD-supply = <®_audio_codec>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sound_novena>; + clocks = <&clks IMX6QDL_CLK_CKO1>; + assigned-clocks = <&clks IMX6QDL_CLK_CKO>, + <&clks IMX6QDL_CLK_CKO1_SEL>, + <&clks IMX6QDL_CLK_PLL4_AUDIO>, + <&clks IMX6QDL_CLK_CKO1>; + assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, + <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, + <&clks IMX6QDL_CLK_OSC>, + <&clks IMX6QDL_CLK_CKO1_PODF>; + assigned-clock-rates = <0 0 722534400 22579200>; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_novena>; + linux,keymap = < + MATRIX_KEY(1, 1, KEY_CONFIG) + >; + status = "okay"; +}; + +&ldb { + fsl,dual-channel; + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + fsl,panel = <&panel>; + status = "okay"; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie_novena>; + reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sata { + target-supply = <®_sata>; + fsl,transmit-level-mV = <1025>; + fsl,transmit-boost-mdB = <0>; + fsl,transmit-atten-16ths = <8>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_novena>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_novena>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_novena>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + dr_mode = "otg"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_novena>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_swbst>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_novena>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3_novena>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&iomuxc { + pinctrl_audmux_novena: audmuxgrp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight_novena: backlightgrp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b1 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1 + >; + }; + + pinctrl_ecspi3_novena: ecspi3grp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + >; + }; + + pinctrl_enet_novena: enetgrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b028 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b028 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b028 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b028 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + /* Ethernet reset */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b1 + >; + }; + + pinctrl_fpga_gpio: fpgagpiogrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b1 + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b1 + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b1 + MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b1 + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1 + MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1 + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b1 + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1 + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b1 + MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b1 + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b1 + MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b1 + MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x1b0b1 + MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b1 + MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x1b0b1 + MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b1 + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b1 + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b1 + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b1 + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1 + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b1 + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1b0b1 + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b1 + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b1 + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b1 + >; + }; + + pinctrl_fpga_eim: fpgaeimgrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0f1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0f1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0f1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0f1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0f1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0f1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0f1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0f1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0f1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0f1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0f1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0f1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0f1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0f1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0f1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0f1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0f1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0f1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0f1 + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0f1 + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0f1 + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0f1 + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0f1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0f1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1 + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0f1 + >; + }; + + pinctrl_gpio_keys_novena: gpiokeysgrp-novena { + fsl,pins = < + /* User button */ + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 + /* PCIe Wakeup */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1f0e0 + /* Lid switch */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 + >; + }; + + pinctrl_hdmi_novena: hdmigrp-novena { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b1 + >; + }; + + pinctrl_i2c1_novena: i2c1grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2_novena: i2c2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_novena: i2c3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_kpp_novena: kppgrp-novena { + fsl,pins = < + /* Front panel button */ + MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1 + /* Fake column driver, not connected */ + MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1 + >; + }; + + pinctrl_leds_novena: ledsgrp-novena { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b1 + >; + }; + + pinctrl_pcie_novena: pciegrp-novena { + fsl,pins = < + /* Reset */ + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 + /* Power On */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b1 + /* Wifi kill */ + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b1 + >; + }; + + pinctrl_sata_novena: satagrp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b1 + >; + }; + + pinctrl_senoko_novena: senokogrp-novena { + fsl,pins = < + /* Senoko IRQ line */ + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048 + /* Senoko reset line */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b1 + >; + }; + + pinctrl_sound_novena: soundgrp-novena { + fsl,pins = < + /* Audio power regulator */ + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b1 + /* Headphone plug */ + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b1 + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + >; + }; + + pinctrl_stmpe_novena: stmpegrp-novena { + fsl,pins = < + /* Touchscreen interrupt */ + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b1 + >; + }; + + pinctrl_uart2_novena: uart2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3_novena: uart3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4_novena: uart4grp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg_novena: usbotggrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc2_novena: usdhc2grp-novena { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + /* Write protect */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1 + /* Card detect */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1 + >; + }; + + pinctrl_usdhc3_novena: usdhc3grp-novena { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + >; + }; +}; -- cgit v1.2.3 From 865fc4014d8745dedec81dc9a1ab9bcfaba1e792 Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Fri, 18 Dec 2015 12:00:32 -0500 Subject: ARM: dts: ts-4800: Add LCD support This commit adds LCD support for the TS-4800. The panel is an Okaya RS800480T-7X0WQ and the timings have been extracted from Technologic Systems' tree. Signed-off-by: Damien Riegel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-ts4800.dts | 102 +++++++++++++++++++++++++++++++++++++ 1 file changed, 102 insertions(+) diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts index 83352cb3f2d3..aa8f00a04a38 100644 --- a/arch/arm/boot/dts/imx51-ts4800.dts +++ b/arch/arm/boot/dts/imx51-ts4800.dts @@ -30,6 +30,53 @@ clock-frequency = <24576000>; }; }; + + backlight_reg: regulator-backlight { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enable_lcd>; + regulator-name = "enable_lcd_reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 78770>; + brightness-levels = <0 150 200 255>; + default-brightness-level = <1>; + power-supply = <&backlight_reg>; + }; + + display0: display@di0 { + compatible = "fsl,imx-parallel-display"; + interface-pix-fmt = "rgb24"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd>; + + display-timings { + 800x480p60 { + native-mode; + clock-frequency = <30066000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <50>; + hback-porch = <70>; + hsync-len = <50>; + vback-porch = <0>; + vfront-porch = <0>; + vsync-len = <50>; + }; + }; + + port@0 { + display0_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; + }; }; &esdhc1 { @@ -60,6 +107,16 @@ }; }; +&ipu_di0_disp0 { + remote-endpoint = <&display0_in>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm_backlight>; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; @@ -115,6 +172,12 @@ >; }; + pinctrl_enable_lcd: enablelcdgrp { + fsl,pins = < + MX51_PAD_CSI2_D12__GPIO4_9 0x1c5 + >; + }; + pinctrl_esdhc1: esdhc1grp { fsl,pins = < MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 @@ -159,6 +222,45 @@ >; }; + pinctrl_lcd: lcdgrp { + fsl,pins = < + MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5 + MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5 + MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5 + MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5 + MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5 + MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5 + MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5 + MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5 + MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5 + MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5 + MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5 + MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5 + MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5 + MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5 + MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5 + MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5 + MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5 + MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5 + MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5 + MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5 + MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5 + MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5 + MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5 + MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5 + MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 + MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 + MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK 0x5 + MX51_PAD_DI_GP4__DI2_PIN15 0x5 + >; + }; + + pinctrl_pwm_backlight: backlightgrp { + fsl,pins = < + MX51_PAD_GPIO1_2__PWM1_PWMO 0x80000000 + >; + }; + pinctrl_uart1: uart1grp { fsl,pins = < MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 -- cgit v1.2.3 From f736c596f439cc4e768579f61ba081192a38d4ac Mon Sep 17 00:00:00 2001 From: Damien Riegel Date: Fri, 18 Dec 2015 12:00:33 -0500 Subject: ARM: dts: TS-4800: add touchscreen support This commit enables the touchscreen on TS-4800, using the ts4800-ts driver. Signed-off-by: Damien Riegel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-ts4800.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts index aa8f00a04a38..0ff76a1bc0f1 100644 --- a/arch/arm/boot/dts/imx51-ts4800.dts +++ b/arch/arm/boot/dts/imx51-ts4800.dts @@ -159,6 +159,12 @@ syscon = <&syscon 0xe>; }; }; + + touchscreen { + compatible = "technologic,ts4800-ts"; + reg = <0x12000 0x1000>; + syscon = <&syscon 0x10 6>; + }; }; }; -- cgit v1.2.3 From 470f269ce3ff325d44bba94b3a746f87f56a387d Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 22 Dec 2015 10:15:19 +0200 Subject: ARM: dts: imx7d: cl-som-imx7: add basic module support CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on Freescale i.MX7 System-on-Chip family. http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/ Add basic DT support for standalone module (without a carrier board): * Memory configuration * eMMC * 2x Gigabit Ethernet ports (FEC1 and FEC2) * I2C2 bus * EEPROM * PCA9555 GPIO extender * PMIC * UART1 * USB OTG port Signed-off-by: Ilya Ledvich Signed-off-by: Igor Grinberg --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx7d-cl-som-imx7.dts | 286 ++++++++++++++++++++++++++++++++ 2 files changed, 287 insertions(+) create mode 100644 arch/arm/boot/dts/imx7d-cl-som-imx7.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f0573a8dd6d2..c0d7a9661e9c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -352,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-14x14-evk.dtb dtb-$(CONFIG_SOC_IMX7D) += \ + imx7d-cl-som-imx7.dtb \ imx7d-sdb.dtb dtb-$(CONFIG_SOC_LS1021A) += \ ls1021a-qds.dtb \ diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts new file mode 100644 index 000000000000..48634519d13a --- /dev/null +++ b/arch/arm/boot/dts/imx7d-cl-som-imx7.dts @@ -0,0 +1,286 @@ +/* + * Support for CompuLab CL-SOM-iMX7 System-on-Module + * + * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * Author: Ilya Ledvich + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + */ + +/dts-v1/; + +#include +#include "imx7d.dtsi" + +/ { + model = "CompuLab CL-SOM-iMX7"; + compatible = "compulab,cl-som-imx7", "fsl,imx7d"; + + memory { + reg = <0x80000000 0x10000000>; /* 256 MB - minimal configuration */ + }; + + reg_usb_otg1_vbus: regulator-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&cpu0 { + arm-supply = <&sw1a_reg>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>, + <&clks IMX7D_ENET1_TIME_ROOT_CLK>; + assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>; + assigned-clock-rates = <0>, <100000000>; + phy-mode = "rgmii"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>, + <&clks IMX7D_ENET2_TIME_ROOT_CLK>; + assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>; + assigned-clock-rates = <0>, <100000000>; + phy-mode = "rgmii"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: pmic@8 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1a { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + /* use sw1c_reg to align with pfuze100/pfuze200 */ + sw1c_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen2_reg: vldo2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vccsd { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: v33 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + + eeprom@50 { + compatible = "atmel,24c08"; + reg = <0x50>; + pagesize = <16>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>; + assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>; + assigned-clock-rates = <400000000>; + bus-width = <8>; + fsl,tuning-step = <2>; + non-removable; + status = "okay"; +}; + +&iomuxc { + pinctrl_enet1: enet1grp { + fsl,pins = < + MX7D_PAD_SD2_CD_B__ENET1_MDIO 0x3 + MX7D_PAD_SD2_WP__ENET1_MDC 0x3 + MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1 + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1 + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1 + MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1 + MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1 + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1 + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1 + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1 + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1 + MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1 + MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1 + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC 0x1 + MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 0x1 + MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 0x1 + MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 0x1 + MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3 0x1 + MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x1 + MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC 0x1 + MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 0x1 + MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1 0x1 + MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2 0x1 + MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 0x1 + MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f + MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79 + MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79 + >; + }; + + pinctrl_usbotg1: usbotg1grp { + fsl,pins = < + MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x14 /* OTG PWREN */ + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX7D_PAD_SD3_CMD__SD3_CMD 0x59 + MX7D_PAD_SD3_CLK__SD3_CLK 0x19 + MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59 + MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59 + MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59 + MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59 + MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59 + MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59 + MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59 + MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59 + MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19 + >; + }; +}; -- cgit v1.2.3 From 67fea0f43d151a4688df1fa4c945f72a26dfb545 Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 22 Dec 2015 10:15:20 +0200 Subject: ARM: dts: imx7d: sbc-imx7: add basic board support SBC-iMX7 is a single board computer designed for industrial and embedded applications. It is based on the Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with the CL-SOM-iMX7 System-on-Module providing most of the functions, and SB-SOM-iMX7 carrier board providing additional peripheral functions and connectors. http://www.compulab.co.il/products/sbcs/sbc-imx7-freescale-i-mx-7-single-board-computer/ http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/ Add basic board support, including SD card as a secondary boot and storage device Signed-off-by: Ilya Ledvich Signed-off-by: Igor Grinberg --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx7d-sbc-imx7.dts | 42 ++++++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+) create mode 100644 arch/arm/boot/dts/imx7d-sbc-imx7.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c0d7a9661e9c..0b00a9cad8c9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -353,6 +353,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-14x14-evk.dtb dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-cl-som-imx7.dtb \ + imx7d-sbc-imx7.dtb \ imx7d-sdb.dtb dtb-$(CONFIG_SOC_LS1021A) += \ ls1021a-qds.dtb \ diff --git a/arch/arm/boot/dts/imx7d-sbc-imx7.dts b/arch/arm/boot/dts/imx7d-sbc-imx7.dts new file mode 100644 index 000000000000..d63c597c0783 --- /dev/null +++ b/arch/arm/boot/dts/imx7d-sbc-imx7.dts @@ -0,0 +1,42 @@ +/* + * Support for CompuLab SBC-iMX7 Single Board Computer + * + * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ + * Author: Ilya Ledvich + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + */ + +#include "imx7d-cl-som-imx7.dts" + +/ { + model = "CompuLab SBC-iMX7"; + compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; + enable-sdio-wakeup; + status = "okay"; +}; + +&iomuxc { + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX7D_PAD_SD1_CMD__SD1_CMD 0x59 + MX7D_PAD_SD1_CLK__SD1_CLK 0x19 + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59 + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59 + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59 + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59 + MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x59 /* CD */ + MX7D_PAD_SD1_WP__GPIO5_IO1 0x59 /* WP */ + >; + }; +}; -- cgit v1.2.3 From cad008b8a77e66b799db3aa128873542b3fb9256 Mon Sep 17 00:00:00 2001 From: Marc Gonzalez Date: Tue, 15 Dec 2015 10:39:19 +0100 Subject: ARM: dts: tango4: Initial device trees This device tree was tested on a Sigma Designs SMP8758 Vantage-1172 Rev E1 development board. Signed-off-by: Marc Gonzalez Reviewed-by: Kevin Hilman Signed-off-by: Olof Johansson --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/tango4-common.dtsi | 130 ++++++++++++++++++++++++++++++ arch/arm/boot/dts/tango4-smp8758.dtsi | 31 +++++++ arch/arm/boot/dts/tango4-vantage-1172.dts | 37 +++++++++ 4 files changed, 200 insertions(+) create mode 100644 arch/arm/boot/dts/tango4-common.dtsi create mode 100644 arch/arm/boot/dts/tango4-smp8758.dtsi create mode 100644 arch/arm/boot/dts/tango4-vantage-1172.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c1ac5f2932d1..c34dcbde8539 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -693,6 +693,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \ dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ sun9i-a80-cubieboard4.dtb +dtb-$(CONFIG_ARCH_TANGO) += \ + tango4-vantage-1172.dtb dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \ tegra20-harmony.dtb \ tegra20-iris-512.dtb \ diff --git a/arch/arm/boot/dts/tango4-common.dtsi b/arch/arm/boot/dts/tango4-common.dtsi new file mode 100644 index 000000000000..ef665d21d317 --- /dev/null +++ b/arch/arm/boot/dts/tango4-common.dtsi @@ -0,0 +1,130 @@ +/* + * Based on Mans Rullgard's Tango3 DT + * https://github.com/mansr/linux-tangox + */ + +#define CPU_CLK 0 +#define SYS_CLK 1 + +#include + +/ { + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>; + + periph_clk: periph_clk { + compatible = "fixed-factor-clock"; + clocks = <&clkgen CPU_CLK>; + clock-mult = <1>; + clock-div = <2>; + #clock-cells = <0>; + }; + + mpcore { + compatible = "simple-bus"; + ranges = <0x00000000 0x20000000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + + scu@0 { + compatible = "arm,cortex-a9-scu"; + reg = <0x0 0x100>; + }; + + twd@600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0x600 0x10>; + interrupts = ; + clocks = <&periph_clk>; + always-on; + }; + + gic: interrupt-controller@1000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x1000 0x1000>, <0x100 0x100>; + }; + }; + + l2cc: l2-cache-controller@20100000 { + compatible = "arm,pl310-cache"; + reg = <0x20100000 0x1000>; + cache-level = <2>; + cache-unified; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&irq0>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + xtal: xtal { + compatible = "fixed-clock"; + clock-frequency = <27000000>; + #clock-cells = <0>; + }; + + clkgen: clkgen@10000 { + compatible = "sigma,tango4-clkgen"; + reg = <0x10000 0x40>; + clocks = <&xtal>; + #clock-cells = <1>; + }; + + tick-counter@10048 { + compatible = "sigma,tick-counter"; + reg = <0x10048 0x4>; + clocks = <&xtal>; + }; + + uart: serial@10700 { + compatible = "ralink,rt2880-uart"; + reg = <0x10700 0x30>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <7372800>; + reg-shift = <2>; + }; + + eth0: ethernet@26000 { + compatible = "sigma,smp8734-ethernet"; + reg = <0x26000 0x800>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkgen SYS_CLK>; + }; + + intc: interrupt-controller@6e000 { + compatible = "sigma,smp8642-intc"; + reg = <0x6e000 0x400>; + ranges = <0 0x6e000 0x400>; + interrupt-parent = <&gic>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <1>; + + irq0: irq0@000 { + reg = <0x000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = ; + }; + + irq1: irq1@100 { + reg = <0x100 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = ; + }; + + irq2: irq2@300 { + reg = <0x300 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = ; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tango4-smp8758.dtsi b/arch/arm/boot/dts/tango4-smp8758.dtsi new file mode 100644 index 000000000000..7ed88ee629fb --- /dev/null +++ b/arch/arm/boot/dts/tango4-smp8758.dtsi @@ -0,0 +1,31 @@ +#include + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "sigma,tango4-smp"; + + cpu0: cpu@0 { + compatible = "arm,cortex-a9"; + next-level-cache = <&l2cc>; + device_type = "cpu"; + reg = <0>; + }; + + cpu1: cpu@1 { + compatible = "arm,cortex-a9"; + next-level-cache = <&l2cc>; + device_type = "cpu"; + reg = <1>; + }; + }; + + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupt-affinity = <&cpu0>, <&cpu1>; + interrupts = + , + ; + }; +}; diff --git a/arch/arm/boot/dts/tango4-vantage-1172.dts b/arch/arm/boot/dts/tango4-vantage-1172.dts new file mode 100644 index 000000000000..3e5b9c81a51c --- /dev/null +++ b/arch/arm/boot/dts/tango4-vantage-1172.dts @@ -0,0 +1,37 @@ +/dts-v1/; + +#include "tango4-smp8758.dtsi" +#include "tango4-common.dtsi" + +/ { + model = "Sigma Designs SMP8758 Vantage-1172 Rev E1"; + compatible = "sigma,vantage-1172", "sigma,smp8758", "sigma,tango4"; + + aliases { + serial = &uart; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; /* 2 GB */ + }; + + chosen { + stdout-path = "serial:115200n8"; + }; +}; + +ð0 { + phy-connection-type = "rgmii"; + phy-handle = <ð0_phy>; + #address-cells = <1>; + #size-cells = <0>; + + /* Atheros AR8035 */ + eth0_phy: ethernet-phy@4 { + compatible = "ethernet-phy-id004d.d072", + "ethernet-phy-ieee802.3-c22"; + interrupts = <37 IRQ_TYPE_EDGE_RISING>; + reg = <4>; + }; +}; -- cgit v1.2.3 From c46ab06101fdd3dcc5355f61e604c5d954cc263c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:20 -0800 Subject: ARM: dts: Add basic support for dra62x j5-eco SoC The dra762x j5-eco is similar to dm814x with a bit different clocks and devices. [tony@atomide.com: updated to leave out adpll clock driver references] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra62x-clocks.dtsi | 23 +++++++++++++++++++++++ arch/arm/boot/dts/dra62x.dtsi | 23 +++++++++++++++++++++++ 2 files changed, 46 insertions(+) create mode 100644 arch/arm/boot/dts/dra62x-clocks.dtsi create mode 100644 arch/arm/boot/dts/dra62x.dtsi diff --git a/arch/arm/boot/dts/dra62x-clocks.dtsi b/arch/arm/boot/dts/dra62x-clocks.dtsi new file mode 100644 index 000000000000..6f98dc8df9dd --- /dev/null +++ b/arch/arm/boot/dts/dra62x-clocks.dtsi @@ -0,0 +1,23 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "dm814x-clocks.dtsi" + +/* + * Compared to dm814x, dra62x has different shifts and more mux options. + * Please add the extra options for ysclk_14 and 16 if really needed. + */ +&timer1_fck { + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <4>; +}; + +&timer2_fck { + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <8>; +}; diff --git a/arch/arm/boot/dts/dra62x.dtsi b/arch/arm/boot/dts/dra62x.dtsi new file mode 100644 index 000000000000..d3cbb4ea35a8 --- /dev/null +++ b/arch/arm/boot/dts/dra62x.dtsi @@ -0,0 +1,23 @@ +/* + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include "dm814x.dtsi" + +/ { + compatible = "ti,dra62x"; +}; + +/* Compared to dm814x, dra62x has different offsets for Ethernet */ +&mac { + reg = <0x4a100000 0x800 + 0x4a101200 0x100>; +}; + +&davinci_mdio { + reg = <0x4a101000 0x100>; +}; + +#include "dra62x-clocks.dtsi" -- cgit v1.2.3 From 124bfc66c5a7097de99987110a215f45e0e1fcd7 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:28 -0800 Subject: ARM: dts: Add minimal dra62x j5-eco evm support This allows us to boot dra62x j5-eco evm with NFSroot. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/Makefile | 3 ++- arch/arm/boot/dts/dra62x-j5eco-evm.dts | 28 ++++++++++++++++++++++++++++ 2 files changed, 30 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/dra62x-j5eco-evm.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..aa237cf14b52 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -452,7 +452,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += \ dtb-$(CONFIG_SOC_TI81XX) += \ dm8148-evm.dtb \ dm8148-t410.dtb \ - dm8168-evm.dtb + dm8168-evm.dtb \ + dra62x-j5eco-evm.dtb dtb-$(CONFIG_SOC_AM33XX) += \ am335x-baltos-ir5221.dtb \ am335x-base0033.dtb \ diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts new file mode 100644 index 000000000000..49a05d2273b1 --- /dev/null +++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts @@ -0,0 +1,28 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "dra62x.dtsi" + +/ { + model = "DRA62x J5 Eco EVM"; + compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii"; +}; -- cgit v1.2.3 From b4d6df2a2324dbf567592d7995738950b5c325a5 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:33 -0800 Subject: ARM: dts: Add pinctrl macros for dm814x Let's add the DM814X_IOPAD macro the same way as we have for dm816x and am33xx as this allows comparing the registers with the documentation easily. The pinctrl bits are yet again different on dm814x. Cc: Linus Walleij Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm814x.dtsi | 2 +- include/dt-bindings/pinctrl/dm814x.h | 48 ++++++++++++++++++++++++++++++++++++ include/dt-bindings/pinctrl/omap.h | 1 + 3 files changed, 50 insertions(+), 1 deletion(-) create mode 100644 include/dt-bindings/pinctrl/dm814x.h diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi index 09a8d88bde23..ca9234633039 100644 --- a/arch/arm/boot/dts/dm814x.dtsi +++ b/arch/arm/boot/dts/dm814x.dtsi @@ -5,7 +5,7 @@ */ #include -#include +#include #include "skeleton.dtsi" diff --git a/include/dt-bindings/pinctrl/dm814x.h b/include/dt-bindings/pinctrl/dm814x.h new file mode 100644 index 000000000000..0f484273da0d --- /dev/null +++ b/include/dt-bindings/pinctrl/dm814x.h @@ -0,0 +1,48 @@ +/* + * This header provides constants specific to DM814X pinctrl bindings. + */ + +#ifndef _DT_BINDINGS_PINCTRL_DM814X_H +#define _DT_BINDINGS_PINCTRL_DM814X_H + +#include + +#undef INPUT_EN +#undef PULL_UP +#undef PULL_ENA + +/* + * Note that dm814x silicon revision 2.1 and older require input enabled + * (bit 18 set) for all 3.3V I/Os to avoid cumulative hardware damage. For + * more info, see errata advisory 2.1.87. We leave bit 18 out of + * function-mask in dm814x.h and rely on the bootloader for it. + */ +#define INPUT_EN (1 << 18) +#define PULL_UP (1 << 17) +#define PULL_DISABLE (1 << 16) + +/* update macro depending on INPUT_EN and PULL_ENA */ +#undef PIN_OUTPUT +#undef PIN_OUTPUT_PULLUP +#undef PIN_OUTPUT_PULLDOWN +#undef PIN_INPUT +#undef PIN_INPUT_PULLUP +#undef PIN_INPUT_PULLDOWN + +#define PIN_OUTPUT (PULL_DISABLE) +#define PIN_OUTPUT_PULLUP (PULL_UP) +#define PIN_OUTPUT_PULLDOWN 0 +#define PIN_INPUT (INPUT_EN | PULL_DISABLE) +#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (INPUT_EN) + +/* undef non-existing modes */ +#undef PIN_OFF_NONE +#undef PIN_OFF_OUTPUT_HIGH +#undef PIN_OFF_OUTPUT_LOW +#undef PIN_OFF_INPUT_PULLUP +#undef PIN_OFF_INPUT_PULLDOWN +#undef PIN_OFF_WAKEUPENABLE + +#endif + diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h index 13949259705a..d1e1512ac0f1 100644 --- a/include/dt-bindings/pinctrl/omap.h +++ b/include/dt-bindings/pinctrl/omap.h @@ -61,6 +61,7 @@ #define OMAP3430_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25d8) (val) #define OMAP3630_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25a0) (val) #define OMAP3_WKUP_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2a00) (val) +#define DM814X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) #define DM816X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) #define AM33XX_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) #define AM4372_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) -- cgit v1.2.3 From 9a6404226508775c9576d5cc7f33cdee71fd09cc Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:37 -0800 Subject: ARM: dts: Update edma bindings on dm814x to use edma_xbar The edma is the same as on am33xx, except it has four tptc instances. And we need the edma_xbar for at least mmc3, so let's use the edma_xbar and the new binding as suggested by Peter Ujfalusi . Reviewed-by: Peter Ujfalusi [tony@atomide.com: updated for ti,edma-memcpy-channels binding] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm814x.dtsi | 68 ++++++++++++++++++++++++++++++++++++------- 1 file changed, 58 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi index ca9234633039..72e071c4e4fe 100644 --- a/arch/arm/boot/dts/dm814x.dtsi +++ b/arch/arm/boot/dts/dm814x.dtsi @@ -126,8 +126,8 @@ interrupts = <65>; ti,spi-num-cs = <4>; ti,hwmods = "mcspi1"; - dmas = <&edma 16 &edma 17 - &edma 18 &edma 19>; + dmas = <&edma 16 0 &edma 17 0 + &edma 18 0 &edma 19 0>; dma-names = "tx0", "rx0", "tx1", "rx1"; }; @@ -145,7 +145,7 @@ reg = <0x20000 0x2000>; clock-frequency = <48000000>; interrupts = <72>; - dmas = <&edma 26 &edma 27>; + dmas = <&edma 26 0 &edma 27 0>; dma-names = "tx", "rx"; }; @@ -155,7 +155,7 @@ reg = <0x22000 0x2000>; clock-frequency = <48000000>; interrupts = <73>; - dmas = <&edma 28 &edma 29>; + dmas = <&edma 28 0 &edma 29 0>; dma-names = "tx", "rx"; }; @@ -165,7 +165,7 @@ reg = <0x24000 0x2000>; clock-frequency = <48000000>; interrupts = <74>; - dmas = <&edma 30 &edma 31>; + dmas = <&edma 30 0 &edma 31 0>; dma-names = "tx", "rx"; }; @@ -205,6 +205,14 @@ }; }; + edma_xbar: dma-router@f90 { + compatible = "ti,am335x-edma-crossbar"; + reg = <0xf90 0x40>; + #dma-cells = <3>; + dma-requests = <32>; + dma-masters = <&edma>; + }; + /* * Note that silicon revision 2.1 and older * require input enabled (bit 18 set) for all @@ -272,12 +280,52 @@ }; edma: edma@49000000 { - compatible = "ti,edma3"; - ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; - reg = <0x49000000 0x10000>, - <0x44e10f90 0x40>; + compatible = "ti,edma3-tpcc"; + ti,hwmods = "tpcc"; + reg = <0x49000000 0x10000>; + reg-names = "edma3_cc"; interrupts = <12 13 14>; - #dma-cells = <1>; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, + <&edma_tptc2 3>, <&edma_tptc3 0>; + + ti,edma-memcpy-channels = <20 21>; + }; + + edma_tptc0: tptc@49800000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc0"; + reg = <0x49800000 0x100000>; + interrupts = <112>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc1: tptc@49900000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc1"; + reg = <0x49900000 0x100000>; + interrupts = <113>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc2: tptc@49a00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc2"; + reg = <0x49a00000 0x100000>; + interrupts = <114>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc3: tptc@49b00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc3"; + reg = <0x49b00000 0x100000>; + interrupts = <115>; + interrupt-names = "edma3_tcerrint"; }; /* See TRM "Table 1-318. L4HS Instance Summary" */ -- cgit v1.2.3 From 609e55745fd6dd670fed4cbb621f881d2d105162 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:45 -0800 Subject: ARM: dts: Add mmc device entries for dm814x Add mmc device entries for dm814x. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm814x.dtsi | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi index 72e071c4e4fe..75f42976572b 100644 --- a/arch/arm/boot/dts/dm814x.dtsi +++ b/arch/arm/boot/dts/dm814x.dtsi @@ -183,6 +183,28 @@ ti,hwmods = "timer3"; }; + mmc1: mmc@60000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + dmas = <&edma 24 0 + &edma 25 0>; + dma-names = "tx", "rx"; + interrupts = <64>; + interrupt-parent = <&intc>; + reg = <0x60000 0x1000>; + }; + + mmc2: mmc@1d8000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + dmas = <&edma 2 0 + &edma 3 0>; + dma-names = "tx", "rx"; + interrupts = <28>; + interrupt-parent = <&intc>; + reg = <0x1d8000 0x1000>; + }; + control: control@140000 { compatible = "ti,dm814-scm", "simple-bus"; reg = <0x140000 0x20000>; @@ -279,6 +301,15 @@ reg = <0x48200000 0x1000>; }; + /* Board must configure evtmux with edma_xbar for EDMA */ + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + interrupts = <29>; + interrupt-parent = <&intc>; + reg = <0x47810000 0x1000>; + }; + edma: edma@49000000 { compatible = "ti,edma3-tpcc"; ti,hwmods = "tpcc"; -- cgit v1.2.3 From 67b5e9ec96767204c5a210015bd3e9af1192e501 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:51 -0800 Subject: ARM: dts: Add mmc support for dm8148-evm There is a mmc slot on the dm8148-evm that's wired to the sd_1 interface. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8148-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts index 109fd4711647..08d01c3e7cf3 100644 --- a/arch/arm/boot/dts/dm8148-evm.dts +++ b/arch/arm/boot/dts/dm8148-evm.dts @@ -15,6 +15,14 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + /* MIC94060YC6 controlled by SD1_POW pin */ + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &cpsw_emac0 { @@ -26,3 +34,26 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii"; }; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sd1_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; +}; + +&pincntl { + sd1_pins: pinmux_sd1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0800, PIN_INPUT | 0x1) /* SD1_CLK */ + DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1) /* SD1_CMD */ + DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[0] */ + DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[1] */ + DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[2] */ + DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[3] */ + DM814X_IOPAD(0x0924, PIN_OUTPUT | 0x40) /* SD1_POW */ + DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ + >; + }; +}; -- cgit v1.2.3 From 4d810fb219ba4019585a1561e84da1f3276c90f4 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:00:57 -0800 Subject: ARM: dts: Add mmc support for dra62x j5-eco evm There's mmc interface on j5-eco evm that's wired to the sd_1 interface. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra62x-j5eco-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts index 49a05d2273b1..97ac8393e347 100644 --- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts +++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts @@ -15,6 +15,14 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + /* MIC94060YC6 controlled by SD1_POW pin */ + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &cpsw_emac0 { @@ -26,3 +34,26 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii"; }; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sd1_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; +}; + +&pincntl { + sd1_pins: pinmux_sd1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0800, PIN_INPUT | 0x1) /* SD1_CLK */ + DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1) /* SD1_CMD */ + DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[0] */ + DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[1] */ + DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[2] */ + DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[3] */ + DM814X_IOPAD(0x0924, PIN_OUTPUT | 0x40) /* SD1_POW */ + DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ + >; + }; +}; -- cgit v1.2.3 From f24f1bdc02e5afaa977ebdd550ddbceafb3830ae Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:01:03 -0800 Subject: ARM: dts: Enable emmc on hp t410 There's a 2GB emmc on hp t410 that's wired to the sd_2 interface. Note that we also need to configure the evtmux using edma_xbar for edma channels. Let's use the McASP2 channels like the original kernel seems to be doing, most likely the audio on t410 is different from dm814x-evm. Reviewed-by: Peter Ujfalusi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8148-t410.dts | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts index 79838dd8dee7..d1927a77c222 100644 --- a/arch/arm/boot/dts/dm8148-t410.dts +++ b/arch/arm/boot/dts/dm8148-t410.dts @@ -15,6 +15,13 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &cpsw_emac0 { @@ -26,3 +33,31 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii"; }; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&sd2_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + dmas = <&edma_xbar 8 0 1 /* use SDTXEVT1 instead of MCASP0TX */ + &edma_xbar 9 0 2>; /* use SDRXEVT1 instead of MCASP0RX */ + dma-names = "tx", "rx"; +}; + +&pincntl { + sd2_pins: pinmux_sd2_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x09c0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[7] */ + DM814X_IOPAD(0x09c4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[6] */ + DM814X_IOPAD(0x09c8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[5] */ + DM814X_IOPAD(0x09cc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[4] */ + DM814X_IOPAD(0x09d0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[3] */ + DM814X_IOPAD(0x09d4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[2] */ + DM814X_IOPAD(0x09d8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[1] */ + DM814X_IOPAD(0x09dc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[0] */ + DM814X_IOPAD(0x09e0, PIN_INPUT | 0x1) /* SD2_CLK */ + DM814X_IOPAD(0x09f4, PIN_INPUT_PULLUP | 0x2) /* SD2_CMD */ + DM814X_IOPAD(0x0920, PIN_INPUT | 40) /* SD2_SDCD */ + >; + }; +}; -- cgit v1.2.3 From 89639d9fa11e636f1b20681b2815db11123b6a73 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:01:11 -0800 Subject: ARM: dts: Add usb support for dm814x and dra62x The usb is very much like on am33xx, we just put the some of the componends under scm where they belong. Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm814x.dtsi | 125 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 125 insertions(+) diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi index 75f42976572b..a25cd51e39ab 100644 --- a/arch/arm/boot/dts/dm814x.dtsi +++ b/arch/arm/boot/dts/dm814x.dtsi @@ -21,6 +21,10 @@ serial2 = &uart3; ethernet0 = &cpsw_emac0; ethernet1 = &cpsw_emac1; + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; }; cpus { @@ -57,6 +61,113 @@ ranges; ti,hwmods = "l3_main"; + usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + ti,hwmods = "usb_otg_hs"; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&usb_ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@47402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; + }; + /* * See TRM "Table 1-317. L4LS Instance Summary" for hints. * It shows the module target agent registers though, so the @@ -227,6 +338,13 @@ }; }; + usb_ctrl_mod: control@620 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x620 0x10 + 0x648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + edma_xbar: dma-router@f90 { compatible = "ti,am335x-edma-crossbar"; reg = <0xf90 0x40>; @@ -251,6 +369,13 @@ pinctrl-single,register-width = <32>; pinctrl-single,function-mask = <0x307ff>; }; + + usb1_phy: usb-phy@1b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x1b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&usb_ctrl_mod>; + }; }; prcm: prcm@180000 { -- cgit v1.2.3 From e032013fb6a3ce41e9af4612d7968ca8852714ce Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:01:16 -0800 Subject: ARM: dts: Add usb support for dm814x-evm Add usb support for dm814x-evm Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8148-evm.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts index 08d01c3e7cf3..e070862b1038 100644 --- a/arch/arm/boot/dts/dm8148-evm.dts +++ b/arch/arm/boot/dts/dm8148-evm.dts @@ -56,4 +56,28 @@ DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ >; }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ + >; + }; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "host"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; + dr_mode = "host"; }; -- cgit v1.2.3 From 868e247851d53f8c15df34c45eced5824cd53052 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:01:37 -0800 Subject: ARM: dts: Add usb support for hp t410 Add usb support for hp t410 and a fixed regulator for the hub power. Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8148-t410.dts | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts index d1927a77c222..5d4313fd5a46 100644 --- a/arch/arm/boot/dts/dm8148-t410.dts +++ b/arch/arm/boot/dts/dm8148-t410.dts @@ -16,6 +16,17 @@ reg = <0x80000000 0x40000000>; /* 1 GB */ }; + /* gpio9 seems to control USB VBUS regulator and/or hub power */ + usb_power: regulator@9 { + compatible = "regulator-fixed"; + regulator-name = "usb_power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + vmmcsd_fixed: fixedregulator@0 { compatible = "regulator-fixed"; regulator-name = "vmmcsd_fixed"; @@ -60,4 +71,28 @@ DM814X_IOPAD(0x0920, PIN_INPUT | 40) /* SD2_SDCD */ >; }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ + >; + }; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "host"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; + dr_mode = "host"; }; -- cgit v1.2.3 From 43fe6de38ea57bf3ef20e89d8bf9b799a7ff0c0b Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 22 Dec 2015 16:01:41 -0800 Subject: ARM: dts: Add usb support for j5-eco evm Add usb support for j5-eco evm. Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra62x-j5eco-evm.dts | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts index 97ac8393e347..79008069020d 100644 --- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts +++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts @@ -56,4 +56,25 @@ DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ >; }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; +}; + +/* USB0_ID pin state: SW10[1] = 0 cable detection, SW10[1] = 1 ID grounded */ +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "otg"; +}; + +&usb1_phy { + status = "disabled"; +}; + +&usb1 { + status = "disabled"; }; -- cgit v1.2.3 From dfaebb509b9240430aff9482881cdc29f929e7c2 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:47 +0200 Subject: ARM: DTS: da850: fix edma0 reg space The size of the eDMA0 CC register space is 0x8000 and not 0x10000. Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850.dtsi | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index 0bd98cd00816..e73f5efb3aa3 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -152,7 +152,8 @@ }; edma0: edma@01c00000 { compatible = "ti,edma3"; - reg = <0x0 0x10000>; + /* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */ + reg = <0x0 0x8000>; interrupts = <11 13 12>; #dma-cells = <1>; }; -- cgit v1.2.3 From 7a7faedde65307c364f831046ded1a7720d5a6fe Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:48 +0200 Subject: ARM: DTS: da850: Use the new DT bindings for the eDMA3 Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3. With the new bindings boards can customize and tweak the DMA channel priority to match their needs. With the new binding the memcpy is safe to be used since with the old binding it was not possible for a driver to know which channel is allowed to be used as non HW triggered channel. Using the new binding will allow us to reserve PaRAM slots to be used by the DSP which was not possible before and prevented the da850 boards to be moved to DT only. Note that the DMA memcpy is disabled, it can be enabled by reserving channels for memcpy by adding the following property to the edma node: ti,edma-memcpy-channels = <20 21>; /* Reserving channel 20 and 21 for memcpy */ Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850-enbw-cmc.dts | 4 ++++ arch/arm/boot/dts/da850-evm.dts | 4 ++++ arch/arm/boot/dts/da850.dtsi | 26 +++++++++++++++++++++----- 3 files changed, 29 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/da850-enbw-cmc.dts b/arch/arm/boot/dts/da850-enbw-cmc.dts index e750ab9086d5..1811f8275559 100644 --- a/arch/arm/boot/dts/da850-enbw-cmc.dts +++ b/arch/arm/boot/dts/da850-enbw-cmc.dts @@ -28,3 +28,7 @@ }; }; }; + +&edma0 { + ti,edma-reserved-slot-ranges = <32 50>; +}; diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts index 4f935ad9f27b..b7ea8318c7fe 100644 --- a/arch/arm/boot/dts/da850-evm.dts +++ b/arch/arm/boot/dts/da850-evm.dts @@ -242,3 +242,7 @@ tx-num-evt = <32>; rx-num-evt = <32>; }; + +&edma0 { + ti,edma-reserved-slot-ranges = <32 50>; +}; diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index e73f5efb3aa3..6e39f9b06524 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -151,11 +151,27 @@ }; edma0: edma@01c00000 { - compatible = "ti,edma3"; + compatible = "ti,edma3-tpcc"; /* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */ reg = <0x0 0x8000>; - interrupts = <11 13 12>; - #dma-cells = <1>; + reg-names = "edma3_cc"; + interrupts = <11 12>; + interrupt-names = "edma3_ccint", "edma3_ccerrint"; + #dma-cells = <2>; + + ti,tptcs = <&edma0_tptc0 7>, <&edma0_tptc1 0>; + }; + edma0_tptc0: tptc@01c08000 { + compatible = "ti,edma3-tptc"; + reg = <0x8000 0x400>; + interrupts = <13>; + interrupt-names = "edm3_tcerrint"; + }; + edma0_tptc1: tptc@01c08400 { + compatible = "ti,edma3-tptc"; + reg = <0x8400 0x400>; + interrupts = <32>; + interrupt-names = "edm3_tcerrint"; }; serial0: serial@1c42000 { compatible = "ns16550a"; @@ -286,8 +302,8 @@ interrupts = <54>; interrupt-names = "common"; status = "disabled"; - dmas = <&edma0 1>, - <&edma0 0>; + dmas = <&edma0 1 1>, + <&edma0 0 1>; dma-names = "tx", "rx"; }; }; -- cgit v1.2.3 From b47a8560695c552889923c71605000ac1f5e4b2d Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:49 +0200 Subject: ARM: DTS: da850: Enable eDMA1 The eDMA1 in da850 has only one TPTC and for example MMC1 is HW events are handled by it. Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850-enbw-cmc.dts | 4 ++++ arch/arm/boot/dts/da850-evm.dts | 4 ++++ arch/arm/boot/dts/da850.dtsi | 17 +++++++++++++++++ 3 files changed, 25 insertions(+) diff --git a/arch/arm/boot/dts/da850-enbw-cmc.dts b/arch/arm/boot/dts/da850-enbw-cmc.dts index 1811f8275559..645549e14237 100644 --- a/arch/arm/boot/dts/da850-enbw-cmc.dts +++ b/arch/arm/boot/dts/da850-enbw-cmc.dts @@ -32,3 +32,7 @@ &edma0 { ti,edma-reserved-slot-ranges = <32 50>; }; + +&edma1 { + ti,edma-reserved-slot-ranges = <32 90>; +}; diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts index b7ea8318c7fe..ef061e9a2315 100644 --- a/arch/arm/boot/dts/da850-evm.dts +++ b/arch/arm/boot/dts/da850-evm.dts @@ -246,3 +246,7 @@ &edma0 { ti,edma-reserved-slot-ranges = <32 50>; }; + +&edma1 { + ti,edma-reserved-slot-ranges = <32 90>; +}; diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index 6e39f9b06524..c08b6c04fcf1 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -173,6 +173,23 @@ interrupts = <32>; interrupt-names = "edm3_tcerrint"; }; + edma1: edma@01e30000 { + compatible = "ti,edma3-tpcc"; + /* eDMA3 CC1: 0x01e3 0000 - 0x01e3 7fff */ + reg = <0x230000 0x8000>; + reg-names = "edma3_cc"; + interrupts = <93 94>; + interrupt-names = "edma3_ccint", "edma3_ccerrint"; + #dma-cells = <2>; + + ti,tptcs = <&edma1_tptc0 7>; + }; + edma1_tptc0: tptc@01e38000 { + compatible = "ti,edma3-tptc"; + reg = <0x238000 0x400>; + interrupts = <95>; + interrupt-names = "edm3_tcerrint"; + }; serial0: serial@1c42000 { compatible = "ns16550a"; reg = <0x42000 0x100>; -- cgit v1.2.3 From 684892a2f10c1845a35b9cfa4c086d4254bb06ae Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:50 +0200 Subject: ARM: DTS: da850: Enable DMA use for MMC0 Add the needed bindings for MMC0 in order to be able to utilize the DMA instead of PIO mode. Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index c08b6c04fcf1..1538959f2853 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -235,6 +235,8 @@ compatible = "ti,da830-mmc"; reg = <0x40000 0x1000>; interrupts = <16>; + dmas = <&edma0 16 0>, <&edma0 17 0>; + dma-names = "rx", "tx"; status = "disabled"; }; ehrpwm0: ehrpwm@01f00000 { -- cgit v1.2.3 From 3c497582e1e2e3baf88bc994dd1ce3e3422cb00b Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:51 +0200 Subject: ARM: DTS: da850: Add node for mmc1 da850 has two MMC controller, MMCSD1 is served by eDMA1 Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index 1538959f2853..31ca5768fccf 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -239,6 +239,14 @@ dma-names = "rx", "tx"; status = "disabled"; }; + mmc1: mmc@1e1b000 { + compatible = "ti,da830-mmc"; + reg = <0x21b000 0x1000>; + interrupts = <72>; + dmas = <&edma1 28 0>, <&edma1 29 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; ehrpwm0: ehrpwm@01f00000 { compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; #pwm-cells = <3>; -- cgit v1.2.3 From f0ad43539af41bc2f8baff9ce3237d368d55654e Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Thu, 17 Dec 2015 15:27:52 +0200 Subject: ARM: DTS: da850: Enable DMA for SPI1 Add the needed bindings so the SPI driver can use DMA with SPI1. Signed-off-by: Peter Ujfalusi Tested-by: Sushaanth Srirangapathi Signed-off-by: Sekhar Nori --- arch/arm/boot/dts/da850.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi index 31ca5768fccf..226cda76e77c 100644 --- a/arch/arm/boot/dts/da850.dtsi +++ b/arch/arm/boot/dts/da850.dtsi @@ -285,6 +285,8 @@ num-cs = <4>; ti,davinci-spi-intr-line = <1>; interrupts = <56>; + dmas = <&edma0 18 0>, <&edma0 19 0>; + dma-names = "rx", "tx"; status = "disabled"; }; mdio: mdio@1e24000 { -- cgit v1.2.3 From 3752216286e283f55b2cd2f2cb7533895a02ee95 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:08 +0200 Subject: ARM: dts: Mark SDIO as non-removable in exynos5800-peach-pi The Exynos5800 Peach Pi Chromebook has a Marvell WiFi SDIO chip which can't neither be removed nor be detected. But the node isn't marked as non-removable and instead has the broken-cd DT property. This causes the device to be removed when the system enters into a suspend state and the following warnings is shown after a resume: [ 181.944636] mmc2: error -2 during resume (card was removed?) Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5800-peach-pi.dts | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 49a4f43e5ac2..ca3a467a585d 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -672,10 +672,9 @@ &mmc_1 { status = "okay"; num-slots = <1>; - broken-cd; + non-removable; cap-sdio-irq; keep-power-in-suspend; - card-detect-delay = <200>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <1>; samsung,dw-mshc-sdr-timing = <0 1>; -- cgit v1.2.3 From 29a2289debbd4758f80afb6d393701ddb09e296a Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:09 +0200 Subject: ARM: dts: Mark SDIO as non-removable in exynos5420-peach-pit The Exynos5420 Peach Pit Chromebook has a Marvell WiFi SDIO chip which can't neither be removed nor be detected. But the node isn't marked as non-removable and instead has the broken-cd DT property. This causes the device to be removed when the system enters into a suspend state and the following warnings is shown after a resume: [ 181.944636] mmc2: error -2 during resume (card was removed?) Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5420-peach-pit.dts | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 72ba6f032ed7..02e99dbafcfb 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -709,10 +709,9 @@ &mmc_1 { status = "okay"; num-slots = <1>; - broken-cd; + non-removable; cap-sdio-irq; keep-power-in-suspend; - card-detect-delay = <200>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <1>; samsung,dw-mshc-sdr-timing = <0 1>; -- cgit v1.2.3 From 783482725f02b16f4737ef17decb9f2f91d482d5 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:10 +0200 Subject: ARM: dts: Mark SDIO as non-removable in exynos5250-snow-common The Exynos5250 Snow Chromebooks have a Marvell WiFi SDIO chip which can't neither be removed nor be detected. But the node isn't marked as non-removable and instead has the broken-cd DT property. This causes the device to be removed when the system enters into a suspend state and the following warnings is shown after a resume: [ 181.944636] mmc2: error -2 during resume (card was removed?) Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Tomeu Vizoso Tested-by: Tomeu Vizoso Reviewed-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5250-snow-common.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi index 0a7f408824d8..1822c502a25a 100644 --- a/arch/arm/boot/dts/exynos5250-snow-common.dtsi +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -552,10 +552,9 @@ &mmc_3 { status = "okay"; num-slots = <1>; - broken-cd; + non-removable; cap-sdio-irq; keep-power-in-suspend; - card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; -- cgit v1.2.3 From dbe2a40a12c2591e88714ccce796f6f62a1cc25f Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:11 +0200 Subject: ARM: dts: Remove broken-cd from eMMC node in exynos5800-peach-pi The eMMC is non-removable so is marked with the non-removable DT property to avoid having to redetect it after a suspend/resume. But it also has the broken-cd property which is wrong since only one of the DT properties for card detection should be used. Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Alim Akhtar Tested-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index ca3a467a585d..7b018e451880 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -652,12 +652,10 @@ &mmc_0 { status = "okay"; num-slots = <1>; - broken-cd; mmc-hs200-1_8v; mmc-hs400-1_8v; cap-mmc-highspeed; non-removable; - card-detect-delay = <200>; clock-frequency = <800000000>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; -- cgit v1.2.3 From da8d3f39808ee487ca7fe62ce7f645815d9e2f3e Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:12 +0200 Subject: ARM: dts: Remove broken-cd from eMMC node in exynos5420-peach-pi The eMMC is non-removable so is marked with the non-removable DT property to avoid having to redetect it after a suspend/resume. But it also has the broken-cd property which is wrong since only one of the DT properties for card detection should be used. Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Alim Akhtar Tested-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5420-peach-pit.dts | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 02e99dbafcfb..35cfb07dc4bb 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -690,11 +690,9 @@ &mmc_0 { status = "okay"; num-slots = <1>; - broken-cd; mmc-hs200-1_8v; cap-mmc-highspeed; non-removable; - card-detect-delay = <200>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; -- cgit v1.2.3 From 241658f44e120374932ad547d326be2420344943 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 15 Oct 2015 18:51:13 +0200 Subject: ARM: dts: Mark eMMC as non-removable in exynos5250-snow-common The eMMC is non-removable so mark it using the non-removable DT property to avoid having to redetect it after a suspend/resume. Also remove the card-detect-delay property that is not needed with non-removable. Signed-off-by: Javier Martinez Canillas Reviewed-by: Krzysztof Kozlowski Reviewed-by: Tomeu Vizoso Tested-by: Tomeu Vizoso Reviewed-by: Alim Akhtar Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5250-snow-common.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi index 1822c502a25a..5cb33ba5e296 100644 --- a/arch/arm/boot/dts/exynos5250-snow-common.dtsi +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -520,8 +520,7 @@ &mmc_0 { status = "okay"; num-slots = <1>; - broken-cd; - card-detect-delay = <200>; + non-removable; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; -- cgit v1.2.3 From 616d289abac9c63f5a5a56c0deb088360f4aed06 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Tue, 10 Nov 2015 11:24:09 +0100 Subject: ARM: dts: Remove fimd node from exynos5422-odroidxu3-common FIMD device is not used at all on Exynos5422-based Odroid XU3-lite and XU4. XU3 board theorethically can support FIMD with DisplayPort connector, but due to hw limitation/design it doesn't work in most cases. It is also not even enabled in XU3 dts file. FIMD node was enabled mainly due to limitation of early Exynos DRM driver, which didn't initialize properly when no FIMD device was available. This node can be now safely removed from XU3-common dtsi and added layer to Odroid XU3 dts, when Display Port driver gets enabled. Signed-off-by: Marek Szyprowski Tested-by: Krzysztof Kozlowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 1af5bdc2bdb1..9134217446b8 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -67,11 +67,6 @@ <19200000>; }; -&fimd { - status = "okay"; -}; - - &hdmi { status = "okay"; hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; -- cgit v1.2.3 From f038f586c368b1730f51edf2619010b3b348fada Mon Sep 17 00:00:00 2001 From: Andrzej Hajda Date: Wed, 18 Nov 2015 09:33:07 +0100 Subject: dt-bindings: remove deprecated compatible string from exynos-hdmi samsung,exynos5-hdmi compatible was marked as deprecated in Jun 2013. It was never used since then. Signed-off-by: Andrzej Hajda Reviewed-by: Gustavo Padovan Signed-off-by: Krzysztof Kozlowski --- Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index 1fd8cf9cbfac..d474f59be6d6 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -2,10 +2,9 @@ Device-Tree bindings for drm hdmi driver Required properties: - compatible: value should be one among the following: - 1) "samsung,exynos5-hdmi" - 2) "samsung,exynos4210-hdmi" - 3) "samsung,exynos4212-hdmi" - 4) "samsung,exynos5420-hdmi" + 1) "samsung,exynos4210-hdmi" + 2) "samsung,exynos4212-hdmi" + 3) "samsung,exynos5420-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. -- cgit v1.2.3 From a452977c43fa316a17e79c6d094beeabf7226ce5 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 19 Oct 2015 14:00:33 +0900 Subject: ARM: dts: Add PRNG module for exynos4 Add Pseudo Random Number Generator (PRNG) node of Security Sub System (SSS) to Exynos 4 DTSI. Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 3184e10f260a..a6b9913ea2b5 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -954,4 +954,12 @@ power-domains = <&pd_lcd0>; #iommu-cells = <0>; }; + + prng: rng@10830400 { + compatible = "samsung,exynos4-rng"; + reg = <0x10830400 0x200>; + clocks = <&clock CLK_SSS>; + clock-names = "secss"; + status = "disabled"; + }; }; -- cgit v1.2.3 From 4e730c0b9cae11b473fec583e5612d03f90fe495 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 19 Oct 2015 14:00:34 +0900 Subject: ARM: dts: Enable PRNG module on exynos4412-trats2 Enable Pseudo Random Number Generator (PRNG) on Trats2 board. This allows using hardware random number generator: $ echo exynos > /sys/class/misc/hw_random/rng_current Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4412-trats2.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 40a474c4374b..a6f78c3da935 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -1234,6 +1234,10 @@ status = "okay"; }; +&prng { + status = "okay"; +}; + &rtc { status = "okay"; clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; -- cgit v1.2.3 From 0c7e90b53997d558625085678848189206b4143e Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 13 Nov 2015 14:29:43 +0100 Subject: ARM: dts: Add rotator nodes on exynos4 This patch adds device node for Rotator device to Exynos 4210 and 4x12 device tree files. Signed-off-by: Marek Szyprowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4.dtsi | 9 +++++++++ arch/arm/boot/dts/exynos4210.dtsi | 4 ++++ arch/arm/boot/dts/exynos4x12.dtsi | 4 ++++ 3 files changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index a6b9913ea2b5..9e98ba93205d 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -713,6 +713,15 @@ iommus = <&sysmmu_jpeg>; }; + rotator: rotator@12810000 { + compatible = "samsung,exynos4210-rotator"; + reg = <0x12810000 0x64>; + interrupts = <0 83 0>; + clocks = <&clock CLK_ROTATOR>; + clock-names = "rotator"; + iommus = <&sysmmu_rotator>; + }; + hdmi: hdmi@12D00000 { compatible = "samsung,exynos4210-hdmi"; reg = <0x12D00000 0x70000>; diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index 3e5ba665d200..e3048aecbfeb 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -279,3 +279,7 @@ <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>; #clock-cells = <1>; }; + +&rotator { + power-domains = <&pd_lcd0>; +}; diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi index b77dac61ffb5..148b47ad3120 100644 --- a/arch/arm/boot/dts/exynos4x12.dtsi +++ b/arch/arm/boot/dts/exynos4x12.dtsi @@ -339,6 +339,10 @@ compatible = "samsung,exynos4212-jpeg"; }; +&rotator { + compatible = "samsung,exynos4212-rotator"; +}; + &mixer { compatible = "samsung,exynos4212-mixer"; clock-names = "mixer", "hdmi", "sclk_hdmi", "vp"; -- cgit v1.2.3 From 3398a187f074f96d1ecfb27aa33c2c922a72cb59 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 13 Nov 2015 14:29:44 +0100 Subject: ARM: dts: Fix power domain for sysmmu-rotator device on exynos4 Rotator device and it's SYSMMU belongs to different power domains on various Exynos4 SoC revisions: LCD0 for 4210 and TOP for 4x12. This patch fixes this by moving power-domains property to exynos4210.dtsi. TOP power domain is always enabled and it is not represented in DTS. Signed-off-by: Marek Szyprowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4.dtsi | 1 - arch/arm/boot/dts/exynos4210.dtsi | 4 ++++ 2 files changed, 4 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 9e98ba93205d..8af921562bb8 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -949,7 +949,6 @@ interrupts = <5 0>; clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>; - power-domains = <&pd_lcd0>; #iommu-cells = <0>; }; diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index e3048aecbfeb..b7474cf27e82 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -283,3 +283,7 @@ &rotator { power-domains = <&pd_lcd0>; }; + +&sysmmu_rotator { + power-domains = <&pd_lcd0>; +}; -- cgit v1.2.3 From d35e20d9760f810cb278f796e67f542091bdfa16 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 13 Nov 2015 14:29:45 +0100 Subject: ARM: dts: Add rotator node on exynos5250 This patch adds device node for Rotator device to Exynos 5250 device tree file. Signed-off-by: Marek Szyprowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5250.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 88b9cf5f226f..33e2d5f7315b 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -269,6 +269,15 @@ iommu-names = "left", "right"; }; + rotator: rotator@11C00000 { + compatible = "samsung,exynos5250-rotator"; + reg = <0x11C00000 0x64>; + interrupts = <0 84 0>; + clocks = <&clock CLK_ROTATOR>; + clock-names = "rotator"; + iommus = <&sysmmu_rotator>; + }; + tmu: tmu@10060000 { compatible = "samsung,exynos5250-tmu"; reg = <0x10060000 0x100>; -- cgit v1.2.3 From e8769d3add46c4d0c7f313009ecec44e2faba117 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 13 Nov 2015 14:29:46 +0100 Subject: ARM: dts: Add rotator node on exynos5420 This patch adds device node for Rotator device and it's SYSMMU to Exynos 542x device tree file. Signed-off-by: Marek Szyprowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5420.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index 1b3d6c769a3c..48a0a55314f5 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -717,6 +717,15 @@ iommus = <&sysmmu_tv>; }; + rotator: rotator@11C00000 { + compatible = "samsung,exynos5250-rotator"; + reg = <0x11C00000 0x64>; + interrupts = <0 84 0>; + clocks = <&clock CLK_ROTATOR>; + clock-names = "rotator"; + iommus = <&sysmmu_rotator>; + }; + gsc_0: video-scaler@13e00000 { compatible = "samsung,exynos5-gsc"; reg = <0x13e00000 0x1000>; @@ -1059,6 +1068,16 @@ #iommu-cells = <0>; }; + sysmmu_rotator: sysmmu@0x11D40000 { + compatible = "samsung,exynos-sysmmu"; + reg = <0x11D40000 0x1000>; + interrupt-parent = <&combiner>; + interrupts = <4 0>; + clock-names = "sysmmu", "master"; + clocks = <&clock CLK_SMMU_ROTATOR>, <&clock CLK_ROTATOR>; + #iommu-cells = <0>; + }; + sysmmu_jpeg0: sysmmu@0x11F10000 { compatible = "samsung,exynos-sysmmu"; reg = <0x11F10000 0x1000>; -- cgit v1.2.3 From 997a2ec0a4297c5c4c14e1b1a9b01e04a0273ba6 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Thu, 19 Nov 2015 12:51:22 +0100 Subject: ARM: dts: Use peripheral mode for dwc3_1 on exynos5422-odroidxu3 DWC3 device found on Exynos SoCs cannot work in OTG mode alone, because it lacks some OTG related control part. OTG mode operation is possible only with external hardware logic (usually GPIO-based) specific to the board. Right now, however, there is no driver for such logic and no bindings, so the OTG mode is dysfunctional at all (this means that it doesn't work as a peripheral nor as a host). This patch sets the operation mode to peripheral to get DWC3_1 device at least somehow working. This can be later updated, when proper OTG driver and bindings get developed. Signed-off-by: Marek Szyprowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts | 2 +- arch/arm/boot/dts/exynos5422-odroidxu3.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index b1b36081f343..2ae1cf41dcb6 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -67,5 +67,5 @@ }; &usbdrd_dwc3_1 { - dr_mode = "otg"; + dr_mode = "peripheral"; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index 0c0bbdbfd85f..432406db85de 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -98,5 +98,5 @@ }; &usbdrd_dwc3_1 { - dr_mode = "otg"; + dr_mode = "peripheral"; }; -- cgit v1.2.3 From e8d761b85e37bac136dc14e70bf871fd5fbf4443 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Mon, 16 Nov 2015 15:36:54 +0100 Subject: ARM: dts: exynos4210-universal_c210: Disable DMA for UARTs PDMA for UART devices seems not to be working properly on Exynos 4210 revision 0 used in Universal C210 boards, so disable it to let one to use UART devices (driver defaults to PIO mode if DMA is not present). Signed-off-by: Marek Szyprowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210-universal_c210.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts index 81b7ec7b3e31..4f5d37920c8d 100644 --- a/arch/arm/boot/dts/exynos4210-universal_c210.dts +++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts @@ -560,16 +560,24 @@ &serial_0 { status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; }; &serial_1 { status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; }; &serial_2 { status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; }; &serial_3 { status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; }; -- cgit v1.2.3 From 42a966aa7198426620dfa8a28749f0c973fe3ab7 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Wed, 25 Nov 2015 09:11:23 -0300 Subject: ARM: dts: Remove unneeded GPIO include in exynos4412-odroidu3 The header is already included in the exynos4412-odroid-common DTSI so there's no need to do it again in the DTS file. Signed-off-by: Javier Martinez Canillas Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4412-odroidu3.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 646ff0bd001a..dd89f7b37c9f 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -13,7 +13,6 @@ /dts-v1/; #include "exynos4412-odroid-common.dtsi" -#include / { model = "Hardkernel ODROID-U3 board based on Exynos4412"; -- cgit v1.2.3 From f99e9a77011c6b4960ff7cbe3909bee81099a986 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Thu, 26 Nov 2015 13:49:47 +0100 Subject: ARM: dts: MDMA1 device belongs to LCD0 power domain on exynos4210 On Exynos 4210 MDMA1 device belongs to LCD0 power domain, so add proper power-domains property. On Exynos 4x12, it belongs to TOP power domain, which is always enabled, thus require no assignment in exynos4x12.dtsi. Signed-off-by: Marek Szyprowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index b7474cf27e82..aac0f173446a 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -271,6 +271,10 @@ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>; }; +&mdma1 { + power-domains = <&pd_lcd0>; +}; + &pmu_system_controller { clock-names = "clkout0", "clkout1", "clkout2", "clkout3", "clkout4", "clkout8", "clkout9"; -- cgit v1.2.3 From 25cd01b223ba2cf6225b64de09622d570b3b3d34 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Wed, 25 Nov 2015 13:55:26 +0100 Subject: ARM: dts: Add power domain to G2D device on exynos4210 G2D device and it's SYSMMU belongs to LCD0 power domain on Exynos 4210, so add missing power-domains property to G2D device node (G2D's SYSMMU is already bound to LCD0 power domain). Signed-off-by: Marek Szyprowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index aac0f173446a..d2542002c9b7 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -185,6 +185,7 @@ interrupts = <0 89 0>; clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>; clock-names = "sclk_fimg2d", "fimg2d"; + power-domains = <&pd_lcd0>; iommus = <&sysmmu_g2d>; status = "disabled"; }; -- cgit v1.2.3 From bf0dda345b0ee1af287f043857fc34ecfa206293 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Wed, 25 Nov 2015 13:59:58 +0100 Subject: ARM: dts: Unify G2D device node with other devices on exynos4 G2D device is always available and doesn't depend on any external (board specific) peripherals, so it can be unconditionally enabled. Signed-off-by: Marek Szyprowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210-origen.dts | 4 ---- arch/arm/boot/dts/exynos4210-smdkv310.dts | 4 ---- arch/arm/boot/dts/exynos4210.dtsi | 1 - arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 4 ---- arch/arm/boot/dts/exynos4412-origen.dts | 4 ---- arch/arm/boot/dts/exynos4412-smdk4412.dts | 4 ---- arch/arm/boot/dts/exynos4x12.dtsi | 1 - 7 files changed, 22 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index b8f866991bdd..5821ad87e32c 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -138,10 +138,6 @@ status = "okay"; }; -&g2d { - status = "okay"; -}; - &i2c_0 { status = "okay"; samsung,i2c-sda-delay = <100>; diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts index bc1448ba95d3..104cbb33d2bb 100644 --- a/arch/arm/boot/dts/exynos4210-smdkv310.dts +++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts @@ -44,10 +44,6 @@ }; }; -&g2d { - status = "okay"; -}; - &i2c_0 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index d2542002c9b7..c1cb8df6da07 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -187,7 +187,6 @@ clock-names = "sclk_fimg2d", "fimg2d"; power-domains = <&pd_lcd0>; iommus = <&sysmmu_g2d>; - status = "disabled"; }; camera { diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index edf0fc8db6ff..395c3ca9601e 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -177,10 +177,6 @@ assigned-clock-rates = <0>, <176000000>; }; -&g2d { - status = "okay"; -}; - &hdmi { hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index c8d86af2fb98..9e2e24c6177a 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -89,10 +89,6 @@ status = "okay"; }; -&g2d { - status = "okay"; -}; - &i2c_0 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/exynos4412-smdk4412.dts index c2421df1fa43..a130ab39fa77 100644 --- a/arch/arm/boot/dts/exynos4412-smdk4412.dts +++ b/arch/arm/boot/dts/exynos4412-smdk4412.dts @@ -41,10 +41,6 @@ }; }; -&g2d { - status = "okay"; -}; - &keypad { samsung,keypad-num-rows = <3>; samsung,keypad-num-columns = <8>; diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi index 148b47ad3120..84a23f962946 100644 --- a/arch/arm/boot/dts/exynos4x12.dtsi +++ b/arch/arm/boot/dts/exynos4x12.dtsi @@ -116,7 +116,6 @@ clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>; clock-names = "sclk_fimg2d", "fimg2d"; iommus = <&sysmmu_g2d>; - status = "disabled"; }; camera { -- cgit v1.2.3 From ef2a27059226327228238a55208d8c11b80013c9 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Wed, 30 Dec 2015 21:05:09 +0100 Subject: ARM: realview: set up cache correctly on the PB11MPCore The L2 cache comes up in a "safe mode" on the PB11MPCore, as it has several issues. This sets it up properly with the right size and associativity, also requiring the outer sync to be disabled for the machine to boot properly. Cc: Russell King Cc: Arnd Bergmann Signed-off-by: Linus Walleij Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/arm-realview-pb11mp.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts index 896bd21d320c..da755c9851a7 100644 --- a/arch/arm/boot/dts/arm-realview-pb11mp.dts +++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts @@ -99,6 +99,19 @@ <0 31 IRQ_TYPE_LEVEL_HIGH>; cache-unified; cache-level = <2>; + /* + * Override default cache size, sets and + * associativity as these may be erroneously set + * up by boot loader(s), probably for safety + * since th outer sync operation can cause the + * cache to hang unless disabled. + */ + cache-size = <1048576>; // 1MB + cache-sets = <4096>; + cache-line-size = <32>; + arm,shared-override; + arm,parity-enable; + arm,outer-sync-disable; }; scu@1f000000 { -- cgit v1.2.3 From 548c3a39e0359383839d43d0cb435dbb4de101e3 Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Wed, 16 Dec 2015 13:24:40 -0800 Subject: ARM: bcm2835: Split the DT for peripherals from the DT for the CPU The set of peripherals remained constant across bcm2835 (Raspberry Pi 1) and bcm2836 (Raspberry Pi 2), but the CPU was swapped out. Split the files so that we can include just peripheral setup in 2836. Signed-off-by: Eric Anholt Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/bcm2835.dtsi | 194 +------------------------------------- arch/arm/boot/dts/bcm283x.dtsi | 205 +++++++++++++++++++++++++++++++++++++++++ 2 files changed, 206 insertions(+), 193 deletions(-) create mode 100644 arch/arm/boot/dts/bcm283x.dtsi diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index aef64de77495..b83b32639358 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -1,206 +1,14 @@ -#include -#include -#include "skeleton.dtsi" +#include "bcm283x.dtsi" / { compatible = "brcm,bcm2835"; - model = "BCM2835"; - interrupt-parent = <&intc>; - - chosen { - bootargs = "earlyprintk console=ttyAMA0"; - }; soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; ranges = <0x7e000000 0x20000000 0x02000000>; dma-ranges = <0x40000000 0x00000000 0x20000000>; - timer@7e003000 { - compatible = "brcm,bcm2835-system-timer"; - reg = <0x7e003000 0x1000>; - interrupts = <1 0>, <1 1>, <1 2>, <1 3>; - /* This could be a reference to BCM2835_CLOCK_TIMER, - * but we don't have the driver using the common clock - * support yet. - */ - clock-frequency = <1000000>; - }; - - dma: dma@7e007000 { - compatible = "brcm,bcm2835-dma"; - reg = <0x7e007000 0xf00>; - interrupts = <1 16>, - <1 17>, - <1 18>, - <1 19>, - <1 20>, - <1 21>, - <1 22>, - <1 23>, - <1 24>, - <1 25>, - <1 26>, - <1 27>, - <1 28>; - - #dma-cells = <1>; - brcm,dma-channel-mask = <0x7f35>; - }; - - intc: interrupt-controller@7e00b200 { - compatible = "brcm,bcm2835-armctrl-ic"; - reg = <0x7e00b200 0x200>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - watchdog@7e100000 { - compatible = "brcm,bcm2835-pm-wdt"; - reg = <0x7e100000 0x28>; - }; - - clocks: cprman@7e101000 { - compatible = "brcm,bcm2835-cprman"; - #clock-cells = <1>; - reg = <0x7e101000 0x2000>; - - /* CPRMAN derives everything from the platform's - * oscillator. - */ - clocks = <&clk_osc>; - }; - - rng@7e104000 { - compatible = "brcm,bcm2835-rng"; - reg = <0x7e104000 0x10>; - }; - - mailbox: mailbox@7e00b800 { - compatible = "brcm,bcm2835-mbox"; - reg = <0x7e00b880 0x40>; - interrupts = <0 1>; - #mbox-cells = <0>; - }; - - gpio: gpio@7e200000 { - compatible = "brcm,bcm2835-gpio"; - reg = <0x7e200000 0xb4>; - /* - * The GPIO IP block is designed for 3 banks of GPIOs. - * Each bank has a GPIO interrupt for itself. - * There is an overall "any bank" interrupt. - * In order, these are GIC interrupts 17, 18, 19, 20. - * Since the BCM2835 only has 2 banks, the 2nd bank - * interrupt output appears to be mirrored onto the - * 3rd bank's interrupt signal. - * So, a bank0 interrupt shows up on 17, 20, and - * a bank1 interrupt shows up on 18, 19, 20! - */ - interrupts = <2 17>, <2 18>, <2 19>, <2 20>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - uart0: uart@7e201000 { - compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; - reg = <0x7e201000 0x1000>; - interrupts = <2 25>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - }; - - i2s: i2s@7e203000 { - compatible = "brcm,bcm2835-i2s"; - reg = <0x7e203000 0x20>, - <0x7e101098 0x02>; - - dmas = <&dma 2>, - <&dma 3>; - dma-names = "tx", "rx"; - status = "disabled"; - }; - - spi: spi@7e204000 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204000 0x1000>; - interrupts = <2 22>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c0: i2c@7e205000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e205000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - sdhci: sdhci@7e300000 { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clocks BCM2835_CLOCK_EMMC>; - status = "disabled"; - }; - - i2c1: i2c@7e804000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e804000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c2: i2c@7e805000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e805000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - usb@7e980000 { - compatible = "brcm,bcm2835-usb"; - reg = <0x7e980000 0x10000>; - interrupts = <1 9>; - }; - arm-pmu { compatible = "arm,arm1176-pmu"; }; }; - - clocks { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - /* The oscillator is the root of the clock tree. */ - clk_osc: clock@3 { - compatible = "fixed-clock"; - reg = <3>; - #clock-cells = <0>; - clock-output-names = "osc"; - clock-frequency = <19200000>; - }; - - }; }; diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi new file mode 100644 index 000000000000..8a7e72799a5c --- /dev/null +++ b/arch/arm/boot/dts/bcm283x.dtsi @@ -0,0 +1,205 @@ +#include +#include +#include "skeleton.dtsi" + +/* This include file covers the common peripherals and configuration between + * bcm2835 and bcm2836 implementations, leaving the CPU configuration to + * bcm2835.dtsi and bcm2836.dtsi. + */ + +/ { + compatible = "brcm,bcm2835"; + model = "BCM2835"; + interrupt-parent = <&intc>; + + chosen { + bootargs = "earlyprintk console=ttyAMA0"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + timer@7e003000 { + compatible = "brcm,bcm2835-system-timer"; + reg = <0x7e003000 0x1000>; + interrupts = <1 0>, <1 1>, <1 2>, <1 3>; + /* This could be a reference to BCM2835_CLOCK_TIMER, + * but we don't have the driver using the common clock + * support yet. + */ + clock-frequency = <1000000>; + }; + + dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xf00>; + interrupts = <1 16>, + <1 17>, + <1 18>, + <1 19>, + <1 20>, + <1 21>, + <1 22>, + <1 23>, + <1 24>, + <1 25>, + <1 26>, + <1 27>, + <1 28>; + + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7f35>; + }; + + intc: interrupt-controller@7e00b200 { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + watchdog@7e100000 { + compatible = "brcm,bcm2835-pm-wdt"; + reg = <0x7e100000 0x28>; + }; + + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + + /* CPRMAN derives everything from the platform's + * oscillator. + */ + clocks = <&clk_osc>; + }; + + rng@7e104000 { + compatible = "brcm,bcm2835-rng"; + reg = <0x7e104000 0x10>; + }; + + mailbox: mailbox@7e00b800 { + compatible = "brcm,bcm2835-mbox"; + reg = <0x7e00b880 0x40>; + interrupts = <0 1>; + #mbox-cells = <0>; + }; + + gpio: gpio@7e200000 { + compatible = "brcm,bcm2835-gpio"; + reg = <0x7e200000 0xb4>; + /* + * The GPIO IP block is designed for 3 banks of GPIOs. + * Each bank has a GPIO interrupt for itself. + * There is an overall "any bank" interrupt. + * In order, these are GIC interrupts 17, 18, 19, 20. + * Since the BCM2835 only has 2 banks, the 2nd bank + * interrupt output appears to be mirrored onto the + * 3rd bank's interrupt signal. + * So, a bank0 interrupt shows up on 17, 20, and + * a bank1 interrupt shows up on 18, 19, 20! + */ + interrupts = <2 17>, <2 18>, <2 19>, <2 20>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart0: uart@7e201000 { + compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; + reg = <0x7e201000 0x1000>; + interrupts = <2 25>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; + arm,primecell-periphid = <0x00241011>; + }; + + i2s: i2s@7e203000 { + compatible = "brcm,bcm2835-i2s"; + reg = <0x7e203000 0x20>, + <0x7e101098 0x02>; + + dmas = <&dma 2>, + <&dma 3>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + spi: spi@7e204000 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204000 0x1000>; + interrupts = <2 22>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c0: i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sdhci: sdhci@7e300000 { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clocks BCM2835_CLOCK_EMMC>; + status = "disabled"; + }; + + i2c1: i2c@7e804000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e804000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@7e805000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e805000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + usb@7e980000 { + compatible = "brcm,bcm2835-usb"; + reg = <0x7e980000 0x10000>; + interrupts = <1 9>; + }; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + /* The oscillator is the root of the clock tree. */ + clk_osc: clock@3 { + compatible = "fixed-clock"; + reg = <3>; + #clock-cells = <0>; + clock-output-names = "osc"; + clock-frequency = <19200000>; + }; + + }; +}; -- cgit v1.2.3 From 4b8c3907c3090d019efdeb02765db209927c0c4f Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Wed, 16 Dec 2015 15:55:12 -0800 Subject: ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT. For Raspberry Pi 2, we want to use the same general pin assignment bits, but need to use bcm2836.dtsi for the CPU instead. Signed-off-by: Eric Anholt Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/bcm2835-rpi-a-plus.dts | 1 + arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 1 + arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 1 + arch/arm/boot/dts/bcm2835-rpi-b.dts | 1 + arch/arm/boot/dts/bcm2835-rpi.dtsi | 2 -- 5 files changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts index b2bff43b135c..228614ffff44 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts @@ -1,4 +1,5 @@ /dts-v1/; +#include "bcm2835.dtsi" #include "bcm2835-rpi.dtsi" / { diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts index 668442b1bda5..ef5405025223 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts @@ -1,4 +1,5 @@ /dts-v1/; +#include "bcm2835.dtsi" #include "bcm2835-rpi.dtsi" / { diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts index eab8b5916e8a..86f1f2f598a7 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts @@ -1,4 +1,5 @@ /dts-v1/; +#include "bcm2835.dtsi" #include "bcm2835-rpi.dtsi" / { diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts index ff6b2d1c6c90..4859e9d81b23 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts @@ -1,4 +1,5 @@ /dts-v1/; +#include "bcm2835.dtsi" #include "bcm2835-rpi.dtsi" / { diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi index 3572f0367baf..3afb9fefe2d1 100644 --- a/arch/arm/boot/dts/bcm2835-rpi.dtsi +++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi @@ -1,5 +1,3 @@ -#include "bcm2835.dtsi" - / { memory { reg = <0 0x10000000>; -- cgit v1.2.3 From 80534f095f182d9067a9ea02073b37f771f77d40 Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Thu, 16 Apr 2015 15:26:45 -0700 Subject: ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and pinout, but the CPU and memory layout changed to use the 2836. Signed-off-by: Eric Anholt Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/bcm2836-rpi-2-b.dts | 35 ++++++++++++++++ arch/arm/boot/dts/bcm2836.dtsi | 78 +++++++++++++++++++++++++++++++++++ 3 files changed, 115 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/bcm2836-rpi-2-b.dts create mode 100644 arch/arm/boot/dts/bcm2836.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f70d4c1c49e4..a4a6d70e8b26 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -62,7 +62,8 @@ dtb-$(CONFIG_ARCH_BCM2835) += \ bcm2835-rpi-b.dtb \ bcm2835-rpi-b-rev2.dtb \ bcm2835-rpi-b-plus.dtb \ - bcm2835-rpi-a-plus.dtb + bcm2835-rpi-a-plus.dtb \ + bcm2836-rpi-2-b.dtb dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4708-asus-rt-ac56u.dtb \ bcm4708-asus-rt-ac68u.dtb \ diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts new file mode 100644 index 000000000000..ff946661bd13 --- /dev/null +++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts @@ -0,0 +1,35 @@ +/dts-v1/; +#include "bcm2836.dtsi" +#include "bcm2835-rpi.dtsi" + +/ { + compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; + model = "Raspberry Pi 2 Model B"; + + memory { + reg = <0 0x40000000>; + }; + + leds { + act { + gpios = <&gpio 47 0>; + }; + + pwr { + label = "PWR"; + gpios = <&gpio 35 0>; + default-state = "keep"; + linux,default-trigger = "default-on"; + }; + }; +}; + +&gpio { + pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>; + + /* I2S interface */ + i2s_alt0: i2s_alt0 { + brcm,pins = <18 19 20 21>; + brcm,function = ; + }; +}; diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/bcm2836.dtsi new file mode 100644 index 000000000000..9d0651d8f373 --- /dev/null +++ b/arch/arm/boot/dts/bcm2836.dtsi @@ -0,0 +1,78 @@ +#include "bcm283x.dtsi" + +/ { + compatible = "brcm,bcm2836"; + + soc { + ranges = <0x7e000000 0x3f000000 0x1000000>, + <0x40000000 0x40000000 0x00001000>; + dma-ranges = <0xc0000000 0x00000000 0x3f000000>; + + local_intc: local_intc { + compatible = "brcm,bcm2836-l1-intc"; + reg = <0x40000000 0x100>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&local_intc>; + }; + + arm-pmu { + compatible = "arm,cortex-a7-pmu"; + interrupt-parent = <&local_intc>; + interrupts = <9>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupt-parent = <&local_intc>; + interrupts = <0>, // PHYS_SECURE_PPI + <1>, // PHYS_NONSECURE_PPI + <3>, // VIRT_PPI + <2>; // HYP_PPI + always-on; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + v7_cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf00>; + clock-frequency = <800000000>; + }; + + v7_cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf01>; + clock-frequency = <800000000>; + }; + + v7_cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf02>; + clock-frequency = <800000000>; + }; + + v7_cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf03>; + clock-frequency = <800000000>; + }; + }; +}; + +/* Make the BCM2835-style global interrupt controller be a child of the + * CPU-local interrupt controller. + */ +&intc { + compatible = "brcm,bcm2836-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-parent = <&local_intc>; + interrupts = <8>; +}; -- cgit v1.2.3 From ddc5c39af4e25d4d4eca925b792b372eedb778d8 Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Tue, 15 Dec 2015 15:35:59 -0800 Subject: ARM: bcm2835: Add the auxiliary clocks to the device tree. These will be used for enabling UART1, SPI1, and SPI2. Signed-off-by: Eric Anholt Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/bcm283x.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi index 8a7e72799a5c..971e741e5467 100644 --- a/arch/arm/boot/dts/bcm283x.dtsi +++ b/arch/arm/boot/dts/bcm283x.dtsi @@ -152,6 +152,13 @@ status = "disabled"; }; + aux: aux@0x7e215000 { + compatible = "brcm,bcm2835-aux"; + #clock-cells = <1>; + reg = <0x7e215000 0x8>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + }; + sdhci: sdhci@7e300000 { compatible = "brcm,bcm2835-sdhci"; reg = <0x7e300000 0x100>; -- cgit v1.2.3 From 4e333015ed3eeaaa7869723b50ae7270ea178232 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 24 Dec 2015 00:23:40 +0900 Subject: ARM: dts: uniphier: fix a typo in comment block Signed-off-by: Masahiro Yamada Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/uniphier-ph1-ld6b.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/uniphier-ph1-ld6b.dtsi b/arch/arm/boot/dts/uniphier-ph1-ld6b.dtsi index c6499ee65bc6..532115234025 100644 --- a/arch/arm/boot/dts/uniphier-ph1-ld6b.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-ld6b.dtsi @@ -53,7 +53,7 @@ compatible = "socionext,ph1-ld6b"; }; -/* UART3 unavilable: the pads are not wired to the package balls */ +/* UART3 unavailable: the pads are not wired to the package balls */ &serial3 { status = "disabled"; }; -- cgit v1.2.3 From c16d1fdb4ee4142351bdbd57222cdd5d5e25df94 Mon Sep 17 00:00:00 2001 From: Edward Cragg Date: Fri, 27 Nov 2015 09:45:28 +0100 Subject: ARM: meson: Add status LED for Odroid-C1 Add the blue status LED to the Hardkernel Odroid C1 board DTS. Signed-off-by: Signed-off-by: Carlo Caione --- arch/arm/boot/dts/meson8b-odroidc1.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts index a8e2911b2cbe..e50f1a1fdbc7 100644 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -46,6 +46,7 @@ /dts-v1/; #include "meson8b.dtsi" +#include / { model = "Hardkernel ODROID-C1"; @@ -58,6 +59,16 @@ memory { reg = <0x40000000 0x40000000>; }; + + leds { + compatible = "gpio-leds"; + blue { + label = "c1:blue:alive"; + gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; }; &uart_AO { -- cgit v1.2.3 From ea22446a9d170bf7f32bd7f99036e17df918f054 Mon Sep 17 00:00:00 2001 From: Carlo Caione Date: Sun, 8 Nov 2015 13:18:56 +0100 Subject: Documentation: watchdog: Add new bindings for meson8b We make the documentation not meson6 specific anymore and add the new binding for meson8b SoC. Signed-off-by: Carlo Caione --- Documentation/devicetree/bindings/watchdog/meson-wdt.txt | 13 +++++++++++++ Documentation/devicetree/bindings/watchdog/meson6-wdt.txt | 13 ------------- 2 files changed, 13 insertions(+), 13 deletions(-) create mode 100644 Documentation/devicetree/bindings/watchdog/meson-wdt.txt delete mode 100644 Documentation/devicetree/bindings/watchdog/meson6-wdt.txt diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt new file mode 100644 index 000000000000..ae70185d96e6 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -0,0 +1,13 @@ +Meson SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson6-wdt" or "amlogic,meson8b-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@c1109900 { + compatible = "amlogic,meson6-wdt"; + reg = <0xc1109900 0x8>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt deleted file mode 100644 index 9200fc2d508c..000000000000 --- a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt +++ /dev/null @@ -1,13 +0,0 @@ -Meson SoCs Watchdog timer - -Required properties: - -- compatible : should be "amlogic,meson6-wdt" -- reg : Specifies base physical address and size of the registers. - -Example: - -wdt: watchdog@c1109900 { - compatible = "amlogic,meson6-wdt"; - reg = <0xc1109900 0x8>; -}; -- cgit v1.2.3 From e9c478a93c113e0ee47f40b80962abe2e2feccc0 Mon Sep 17 00:00:00 2001 From: Carlo Caione Date: Sun, 8 Nov 2015 13:18:57 +0100 Subject: ARM: dts: meson8b: Add watchdog node With this patch we add the watchdog node in the meson8b DTS file. Signed-off-by: Carlo Caione --- arch/arm/boot/dts/meson8b.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi index ee352bf687ff..8bad5571af46 100644 --- a/arch/arm/boot/dts/meson8b.dtsi +++ b/arch/arm/boot/dts/meson8b.dtsi @@ -105,6 +105,12 @@ #interrupt-cells = <3>; }; + wdt: watchdog@c1109900 { + compatible = "amlogic,meson8b-wdt"; + reg = <0xc1109900 0x8>; + interrupts = <0 0 1>; + }; + timer@c1109940 { compatible = "amlogic,meson6-timer"; reg = <0xc1109940 0x18>; -- cgit v1.2.3 From b66c1ebae17bf78eb915f1d22a82e1183b0deb8e Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:47 +0100 Subject: ARM: dts: bockw: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7778-bockw.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index b1aa02599229..a52b359e2ae2 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -199,6 +199,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From b88ddbdd36859a4dc99bddd9b5730944187530c0 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:48 +0100 Subject: ARM: dts: lager: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7790-lager.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 44ba69b974a2..052dcee4790d 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -449,6 +449,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From f6531bb50847af70aa95665e83873c455d7bf06e Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:49 +0100 Subject: ARM: dts: koelsch: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-koelsch.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index c94a0fb807a2..45256f3cc835 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -489,6 +489,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From 947ef628414483b05eac32253f86ef7753fb4d4d Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:50 +0100 Subject: ARM: dts: porter: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-porter.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index 71ba7b6b3a33..6713b1ea732b 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -200,6 +200,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From e5e6f9b4891af3617a76f5220f1efaf365f837da Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:51 +0100 Subject: ARM: dts: gose: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7793-gose.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index 3e3122490650..baa59fe84298 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -115,6 +115,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From 8bc403b78ffb774d8dc944abb0826c46c0dca09d Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:52 +0100 Subject: ARM: dts: silk: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7794-silk.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index 5a8dcac37c8e..5153e3af25d9 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -204,6 +204,7 @@ m25p,fast-read; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From 9962b3d4f0788e8637211d7b999dcea60430df18 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Wed, 23 Dec 2015 10:22:57 +0800 Subject: ARM: dts: imx6q: clean up unused ipu2grp The pinctrl group ipu2grp is a leftover from the previous iomuxc DT cleanup. It's not used by anyone now. More importantly, it's getting in the way of saving the unnecessary pinfunc container node from the board dts files that include imx6q.dtsi. Let's clean it up. Signed-off-by: Shawn Guo Tested-by: Michael Trimarchi Signed-off-by: Olof Johansson --- arch/arm/boot/dts/imx6q.dtsi | 36 ------------------------------------ 1 file changed, 36 deletions(-) diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 9b6a193b64ca..0d93c0e8f9ba 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -104,42 +104,6 @@ iomuxc: iomuxc@020e0000 { compatible = "fsl,imx6q-iomuxc"; - - ipu2 { - pinctrl_ipu2_1: ipu2grp-1 { - fsl,pins = < - MX6QDL_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK 0x10 - MX6QDL_PAD_DI0_PIN15__IPU2_DI0_PIN15 0x10 - MX6QDL_PAD_DI0_PIN2__IPU2_DI0_PIN02 0x10 - MX6QDL_PAD_DI0_PIN3__IPU2_DI0_PIN03 0x10 - MX6QDL_PAD_DI0_PIN4__IPU2_DI0_PIN04 0x80000000 - MX6QDL_PAD_DISP0_DAT0__IPU2_DISP0_DATA00 0x10 - MX6QDL_PAD_DISP0_DAT1__IPU2_DISP0_DATA01 0x10 - MX6QDL_PAD_DISP0_DAT2__IPU2_DISP0_DATA02 0x10 - MX6QDL_PAD_DISP0_DAT3__IPU2_DISP0_DATA03 0x10 - MX6QDL_PAD_DISP0_DAT4__IPU2_DISP0_DATA04 0x10 - MX6QDL_PAD_DISP0_DAT5__IPU2_DISP0_DATA05 0x10 - MX6QDL_PAD_DISP0_DAT6__IPU2_DISP0_DATA06 0x10 - MX6QDL_PAD_DISP0_DAT7__IPU2_DISP0_DATA07 0x10 - MX6QDL_PAD_DISP0_DAT8__IPU2_DISP0_DATA08 0x10 - MX6QDL_PAD_DISP0_DAT9__IPU2_DISP0_DATA09 0x10 - MX6QDL_PAD_DISP0_DAT10__IPU2_DISP0_DATA10 0x10 - MX6QDL_PAD_DISP0_DAT11__IPU2_DISP0_DATA11 0x10 - MX6QDL_PAD_DISP0_DAT12__IPU2_DISP0_DATA12 0x10 - MX6QDL_PAD_DISP0_DAT13__IPU2_DISP0_DATA13 0x10 - MX6QDL_PAD_DISP0_DAT14__IPU2_DISP0_DATA14 0x10 - MX6QDL_PAD_DISP0_DAT15__IPU2_DISP0_DATA15 0x10 - MX6QDL_PAD_DISP0_DAT16__IPU2_DISP0_DATA16 0x10 - MX6QDL_PAD_DISP0_DAT17__IPU2_DISP0_DATA17 0x10 - MX6QDL_PAD_DISP0_DAT18__IPU2_DISP0_DATA18 0x10 - MX6QDL_PAD_DISP0_DAT19__IPU2_DISP0_DATA19 0x10 - MX6QDL_PAD_DISP0_DAT20__IPU2_DISP0_DATA20 0x10 - MX6QDL_PAD_DISP0_DAT21__IPU2_DISP0_DATA21 0x10 - MX6QDL_PAD_DISP0_DAT22__IPU2_DISP0_DATA22 0x10 - MX6QDL_PAD_DISP0_DAT23__IPU2_DISP0_DATA23 0x10 - >; - }; - }; }; }; -- cgit v1.2.3 From 03b9ee45bcebd1ea2811e7c90d13b6b69b0cce9b Mon Sep 17 00:00:00 2001 From: Roman Volkov Date: Fri, 1 Jan 2016 16:38:12 +0300 Subject: dts: vt8500: Fix errors in SDHC node for WM8505 According to datasheet, the registers space of SDHC controller is 1Kb, not '0x1000', the correct value should be '0x400'. Bracket interrupt numbers individually per recommendations. Signed-off-by: Roman Volkov Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/wm8505.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/wm8505.dtsi b/arch/arm/boot/dts/wm8505.dtsi index a1a854b8a454..e9ef539e13d3 100644 --- a/arch/arm/boot/dts/wm8505.dtsi +++ b/arch/arm/boot/dts/wm8505.dtsi @@ -281,8 +281,8 @@ sdhc@d800a000 { compatible = "wm,wm8505-sdhc"; - reg = <0xd800a000 0x1000>; - interrupts = <20 21>; + reg = <0xd800a000 0x400>; + interrupts = <20>, <21>; clocks = <&clksdhc>; bus-width = <4>; }; -- cgit v1.2.3 From 07ebfa59b9db40ae29fbf2ef24ba7dc5fa8a5dad Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 5 Jan 2016 15:02:08 +0100 Subject: ARM: versatile: add the syscon LEDs to the DT The device tree version of Versatile AP/PB never had LED support so we are missing LEDs from our hardware boards. Add this as syscon LEDs like we did for Integrator and Juno. We need to spawn devices in the syscon with "simple-mfd" for this to work. Signed-off-by: Linus Walleij Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/versatile-ab.dts | 62 +++++++++++++++++++++++++++++++++++++- 1 file changed, 61 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/versatile-ab.dts index 01f40197ea13..7b858258374b 100644 --- a/arch/arm/boot/dts/versatile-ab.dts +++ b/arch/arm/boot/dts/versatile-ab.dts @@ -30,9 +30,69 @@ }; core-module@10000000 { - compatible = "arm,core-module-versatile", "syscon"; + compatible = "arm,core-module-versatile", "syscon", "simple-mfd"; reg = <0x10000000 0x200>; + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "versatile:0"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + led@08.1 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x02>; + label = "versatile:1"; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + led@08.2 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x04>; + label = "versatile:2"; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + led@08.3 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x08>; + label = "versatile:3"; + default-state = "off"; + }; + led@08.4 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x10>; + label = "versatile:4"; + default-state = "off"; + }; + led@08.5 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x20>; + label = "versatile:5"; + default-state = "off"; + }; + led@08.6 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x40>; + label = "versatile:6"; + default-state = "off"; + }; + led@08.7 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x80>; + label = "versatile:7"; + default-state = "off"; + }; + /* OSC1 on AB, OSC4 on PB */ osc1: cm_aux_osc@24M { #clock-cells = <0>; -- cgit v1.2.3 From 0c6623e35992c08d0462504253c669363d3f7ccb Mon Sep 17 00:00:00 2001 From: Ilya Ledvich Date: Tue, 22 Dec 2015 11:10:59 +0200 Subject: ARM: dts: compulab: add new board description Add description for newly introduced Compulab devices: - CL-SOM-iMX7 - SBC-iMX7 Signed-off-by: Ilya Ledvich Acked-by: Rob Herring Signed-off-by: Arnd Bergmann --- .../devicetree/bindings/arm/compulab-boards.txt | 24 ++++++++++++++++++++-- 1 file changed, 22 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/compulab-boards.txt b/Documentation/devicetree/bindings/arm/compulab-boards.txt index 71172d56875c..42a10285af9c 100644 --- a/Documentation/devicetree/bindings/arm/compulab-boards.txt +++ b/Documentation/devicetree/bindings/arm/compulab-boards.txt @@ -1,5 +1,25 @@ -CompuLab SB-SOM is a multi-module baseboard capable of carrying CM-T43, CM-T54, -and CM-QS600 modules with minor modifications to the SB-SOM assembly. +CompuLab SB-SOM is a multi-module baseboard capable of carrying: + - CM-T43 + - CM-T54 + - CM-QS600 + - CL-SOM-AM57x + - CL-SOM-iMX7 +modules with minor modifications to the SB-SOM assembly. Required root node properties: - compatible = should be "compulab,sb-som" + +Compulab CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on +Freescale i.MX7 ARM Cortex-A7 System-on-Chip. + +Required root node properties: + - compatible = "compulab,cl-som-imx7", "fsl,imx7d"; + +Compulab SBC-iMX7 is a single board computer based on the +Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with +the CL-SOM-iMX7 System-on-Module providing most of the functions, +and SB-SOM-iMX7 carrier board providing additional peripheral +functions and connectors. + +Required root node properties: + - compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d"; -- cgit v1.2.3