| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This removes the need to power cycle the Dell WD15 dock if it has been
attached to a Windows machine.
The Windows driver puts the ALC4020 USB audio controller into
'manual mode', and then does all the power management and other
configuration itself, by sending HD audio commands directly to the
ALC3263 audio codec via vendor-type USB messages. If manual mode is off,
this is all handled by the firmware, and works well enough.
If manual mode is turned on, the latency of the SET INTERFACE command
goes from several hundred ms to less than 1 ms
(see https://bugzilla.suse.com/show_bug.cgi?id=1089467), but I'm not
sure if the additional code that would be required is worth it.
Funnily enough, the Windows driver tries to turn off manual mode when
the dock is disconnected, which doesn't work for obvious reasons.
Additionally, fix a bug in dell_dock_init_vol, which didn't work because
the Control Selector was missing.
Now, it properly resets the volume to 0dB.
Fixes: 964af639ad69 ("ALSA: usb-audio: Initialize Dell Dock playback volumes")
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-2-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Dell WD15 dock has a headset and a line out port. Add support for
detecting if a jack is inserted into one of these ports.
For the headset jack, additionally determine if a mic is present.
The WD15 contains an ALC4020 USB audio controller and ALC3263 audio codec
from Realtek. It is a UAC 1 device, and UAC 1 does not support jack
detection. Instead, jack detection works by sending HD Audio commands over
vendor-type USB messages.
I found out how it works by looking at USB captures on Windows.
The audio codec is very similar to the one supported by
sound/soc/codecs/rt298.c / rt298.h, some constant names and the mic
detection are adapted from there. The realtek_add_jack function is adapted
from build_connector_control in sound/usb/mixer.c.
I tested this on a WD15 dock with the latest firmware.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Back-merge of 5.19-rc branch for the futher development, mainly about
USB-audio and HD-audio Cirrus stuff.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.19
A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.
|
|
The patch applies the same quirks used for SC-01 at firmware v1.1.0 to
the ones running v1.0.0, with respect to hard-coded sample rates.
I got two more units and successfully tested the patch series with both
firmwares.
The support is now complete (not accounting ASIO).
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-2-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fiero SC-01 is a USB sound card with two mono inputs and a single
stereo output. The inputs are composed into a single stereo stream.
The device uses a vendor-provided driver on Windows and does not work
at all without it. The driver mostly provides ASIO functionality, but
also alters the way the sound card is queried for sample rates and
clocks.
ALSA queries those failing with an EPIPE (same as Windows 10 does).
Presumably, the vendor-provided driver does not query it at all, simply
matching by VID:PID. Thus, I consider this a buggy firmware and adhere
to a set of fixed endpoint quirks instead.
The soundcard has an internal clock. Implicit feedback mode is required
for the playback.
I have updated my device to v1.1.0 from a Windows 10 VM using a vendor-
provided binary prior to the development, hoping for it to just begin
working. The device provides no obvious way to downgrade the firmware,
and regardless, there's no binary available for v1.0.0 anyway.
Thus, I will be getting another unit to extend the patch with support
for that. Expected to be a simple copy-paste of the existing one,
though.
There were no previous reports of that device in context of Linux
anywhere. Other issues have been reported though, but that's out of the
scope.
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-1-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes headset detection on Clevo L140PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624144109.3957-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
Signed-off-by: John Veness <john-linux@pelago.org.uk>
Link: https://lore.kernel.org/r/20220624140757.28758-1-john-linux@pelago.org.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
madera_adsp_rate_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the
value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
madera_out1_demux_put returns the value of
snd_soc_dapm_mux_update_power, which returns a 1 if a path was found for
the kcontrol. This is obviously different to the expected return a 1 if
the control was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cs47l15_in1_adc_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mixer controls for ASP TX3/4 are set to values that are not included
in their enumeration control. This will cause spurious event
notifications when the controls are first changed, as the register value
changes whilst the actual visible enumeration value does not. Use the
register patch to set them to a known value, zero, which equates to zero
fill, thereby avoiding the spurious notifications.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DAPM keeps a copy of the current value of mux/demux controls,
however this value is only initialised in the case of autodisable
controls. This leads to false notification events when first
modifying a DAPM kcontrol that has a non-zero default.
Autodisable controls are left as they are, since they already
initialise the value, and there would be more work required to
support autodisable muxes where the first option isn't disabled
and/or that isn't the default.
Technically this issue could affect mixer/switch elements as well,
although not on any of the devices I am currently running. There
is also a little more work to do to address the issue there due to
that side supporting stereo controls, so that has not been tackled
in this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220621090719.30558-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Various boolean controls on cs35l41 are missing the required "Switch" in
the name, add these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DRE controls on wm5110 should return a value of 1 if the DRE state
is actually changed, update to fix this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The preloader controls on ADSP should return a value of 1 if the
preloader value was changed, update to correct this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.
Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20220615045643.3137287-1-judyhsiao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.
Make sure regular boot with firmware download is used for S4 and S5.
BugLink: https://github.com/thesofproject/sof/issues/5892
Fixes: 5fb5f51185126 ("ASoC: SOF: Intel: hda-loader: add IMR restore support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing code only deals with S0 and S3, let's start adding S1 and S2.
No functional change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 288fad2f71fa ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
modified the PCM path only, but left the compressed data patch using an
obsolete option.
Move the functionality in a helper that can be called for both PCM and
compressed data.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Fixes: 288fad2f71fa ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201953.130876-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This should return PTR_ERR() instead of IS_ERR().
Fixes: e0100bfd383c ("ASoC: SOF: mediatek: Add mt8186 ipc support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/YqmWIK8sTj578OJP@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "wlf,spkvdd-ena" GPIO needed by the bytcr_wm5102 driver
is made available through a gpio-lookup table.
This gpio-lookup table is registered by drivers/mfd/arizona-spi.c, which
may get probed after the bytcr_wm5102 driver.
If the gpio-lookup table has not registered yet then the gpiod_get()
will return -ENOENT. Treat -ENOENT as -EPROBE_DEFER to still keep
things working in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220612155652.107310-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently wcd938x_*_put() unconditionally report that the value of the
control changed, resulting in spurious events being generated. Return 0 in
that case instead as we should. There is still an issue in the compander
control which is a bit more complex.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220603122526.3914942-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The slimbus mux put operation unconditionally reports a change in value
which means that spurious events are generated. Fix this by exiting early
in that case.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220603124609.4024666-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently in slim_rx_mux_put, an RX channel gets added to a new list
even if it is already in one. This can mess up links and make either
it, the new list head, or both, get linked to the wrong entries.
This can cause an entry to link to itself which in turn ends up
making list_for_each_entry in other functions loop infinitely.
To avoid issues, always remove the RX channel from any list it's in
before adding it to a new list.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20220606152226.149164-1-y.oudjana@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
prepare callback can be called multiple times, so unprepare the stream
if its already prepared.
Without this DSP is not happy to setting the params on a already
prepared graph.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Reported-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220610144818.511797-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use correct type for parsing UUIDs, this eliminates warning present,
when compiling with W=1.
Fixes: 34ae2cd53673 ("ASoC: Intel: avs: Add topology parsing infrastructure")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220610124257.4160658-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sof_ipc3_control_load_bytes()
Move the size checks prior to allocating memory as these checks do not need
the data to be allocated and in case of an error we would not need to free
the allocation.
The max size must not be less than the size of
struct sof_ipc_ctrl_data + struct sof_abi_hdr as the ABI header needs to
be present under all circumstances.
The check was incorrectly used or between the two size checks.
Fixes: b5cee8feb1d4 ("ASoC: SOF: topology: Make control parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610084735.19397-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the comment for the cl_dsp_init() to clarify what is done by the
function and use the chip->init_core_mask instead of BIT(0) when
unstalling/running the init core.
Complements: 2a68ff846164 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The hda_dsp_enable_core() is powering up _and_ unstall the core in one
call while the first step of the firmware loading must not unstall the
core.
The core can be unstalled only after the set cpb_cfp and the configuration
of the IPC register for the ROM_CONTROL message.
Complements: 2a68ff846164 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The hda_dsp_core_power_up() needs to be exposed so that it can be used in
hda-loader.c to correct the boot flow.
The first step must not unstall the core, it should only power up the
core(s).
Add sanity check for the core_mask while exposing it to be safe.
Complements: 2a68ff846164 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Renesas is the only user of ak4613 on upstream for now, and
commit f28dbaa958fbd8 ("ASoC: ak4613: add TDM256 support")
added TDM256 support. Renesas tested part of it, because of
board connection.
It was assuming ak4613 is probed via Audio-Graph-Card, but it
might be probed via Simple-Audio-Card either.
It will indicates WARNING in such case. This patch fixup it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87h74v29f7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .set_jack_detect() codec component callback is invoked during card
registration, which happens when the machine driver is probed.
The issue is that this callback can race with the bus suspend/resume,
and IO timeouts can happen. This can be reproduced very easily if the
machine driver is 'blacklisted' and manually probed after the bus
suspends. The bus and codec need to be re-initialized using pm_runtime
helpers.
Previous contributions tried to make sure accesses to the bus during
the .set_jack_detect() component callback only happen when the bus is
active. This was done by changing the regcache status on a component
remove. This is however a layering violation, the regcache status
should only be modified on device probe, suspend and resume. The
component probe/remove should not modify how the device regcache is
handled. This solution also didn't handle all the possible race
conditions, and the RT700 headset codec was not handled.
This patch tries to resume the codec device before handling the jack
initializations. In case the codec has not yet been initialized,
pm_runtime may not be enabled yet, so we don't squelch the -EACCES
error code and only stop the jack information. When the codec reports
as attached, the jack initialization will proceed as usual.
BugLink: https://github.com/thesofproject/linux/issues/3643
Fixes: 7ad4d237e7c4a ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Fixes: 899b12542b089 ('ASoC: rt711: add snd_soc_component remove callback')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueues are initialized in the io_init functions, which isn't
quite right. In some tests, this leads to warnings throw from
__queue_delayed_work()
WARN_ON_FUNCTION_MISMATCH(timer->function, delayed_work_timer_fn);
Move all the initializations to the probe functions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Realtek headset codec drivers typically check if the card is
instantiated before proceeding with the jack detection.
The rt700, rt711 and rt711-sdca are however missing a check on the
card pointer, which can lead to NULL dereferences encountered in
driver bind/unbind tests.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the same flow as rt711-sdca and initialize all mutexes at probe
time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the card registration fails, typically because of deferred probes,
the device properties added for headset codecs are not removed, which
leads to kernel oopses in driver bind/unbind tests.
We already clean-up the device properties when the card is removed,
this code can be moved as a helper and called upon card registration
errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In codec driver bind/unbind test, the following warning is thrown:
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
...
[ 699.182495] rt711_sdca_jack_init+0x1b/0x1d0 [snd_soc_rt711_sdca]
[ 699.182498] rt711_sdca_set_jack_detect+0x3b/0x90 [snd_soc_rt711_sdca]
[ 699.182500] snd_soc_component_set_jack+0x24/0x50 [snd_soc_core]
A quick check in the code shows that the 'calibrate_mutex' used by
this driver are not initialized at probe time. Moving the
initialization to the probe removes the issue.
BugLink: https://github.com/thesofproject/linux/issues/3644
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When binding/unbinding codec drivers, the following warnings are
thrown:
[ 107.266879] rt715-sdca sdw:3:025d:0714:01: Unbalanced pm_runtime_enable!
[ 306.879700] rt711-sdca sdw:0:025d:0711:01: Unbalanced pm_runtime_enable!
Add a remove callback for all Realtek/Maxim SoundWire codecs and remove this
warning.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both Behringer UMC 202 HD and 404 HD need explicit quirks to enable
the implicit feedback mode and start the playback stream primarily.
The former seems fixing the stuttering and the latter is required for
a playback-only case.
Note that the "clock source 41 is not valid" error message still
appears even after this fix, but it should be only once at probe.
The reason of the error is still unknown, but this seems to be mostly
harmless as it's a one-off error and the driver retires the clock
setup and it succeeds afterwards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624101132.14528-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes headset detection on Clevo NS50PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220622150017.9897-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It's been reported that the recent fix for skipping the
component-binding with D-GPU caused a regression on some systems; it
resulted in the completely missing component binding with i915 GPU.
The problem was the use of pci_get_class() function. It matches with
the full PCI class bits, while we want to match only partially the PCI
base class bits. So, when a system has an i915 graphics device with
the PCI class 0380, it won't hit because we're looking for only the
PCI class 0300.
This patch fixes i915_gfx_present() to look up each PCI device and
match with PCI base class explicitly instead of pci_get_class().
Fixes: c9db8a30d9f0 ("ALSA: hda/i915 - skip acomp init if no matching display")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Tested-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1200611
Link: https://lore.kernel.org/r/87bkunztec.wl-tiwai@suse.de
Link: https://lore.kernel.org/r/20220621120044.11573-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Like the previous fix for Conexant codec, the beep_nid has to be set
up before calling snd_hda_gen_parse_auto_config(); otherwise it'd miss
the path setup.
Fix the call order for addressing the missing beep setup.
Fixes: 0e8f9862493a ("ALSA: hda/via - Simplify control management")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216152
Link: https://lore.kernel.org/r/20220620104008.1994-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently the Conexant codec driver sets up the beep NID after calling
snd_hda_gen_parse_auto_config(). It turned out that this results in
the insufficient setup for the beep control, as the generic parser
handles the fake path in snd_hda_gen_parse_auto_config() only if the
beep_nid is set up beforehand.
For dealing with the beep widget properly, call cx_auto_parse_beep()
before snd_hda_gen_parse_auto_config() call.
Fixes: 51e19ca5f755 ("ALSA: hda/conexant - Clean up beep code")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216152
Link: https://lore.kernel.org/r/20220620104008.1994-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Although snd_rawmidi_drain_output() may take some long time, it has no
protection and intrusive operations like the buffer resize may happen
meanwhile. For making the operation a bit more robust, this patch
takes the buffer refcount for blocking the buffer resize.
Also, as this function is exported, in theory, it might be called
asynchronously from the stream open/close state. For avoiding the
missing refcount, now the close call checks the buffer refcount, too.
Link: https://lore.kernel.org/r/20220617144051.18985-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The rawmidi interface provides some exported functions to be called
from outside, and currently there is no state check for those calls
whether the stream is properly opened and running. Although such an
invalid call shouldn't happen, but who knows.
This patch adds the proper rawmidi stream state checks with spinlocks
for avoiding unexpected accesses when such exported functions are
called in an invalid state. After this patch, with the
substream->opened and substream->runtime are always tied and
guaranteed to be set under substream->lock.
Link: https://lore.kernel.org/r/20220617144051.18985-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The input/output parameter changes are pretty intrusive, possibly
involving with the buffer resizing operation. Hence those should be
performed exclusively; otherwise some ugly race could happen.
This patch puts the existing open_mutex for snd_rawmidi_input_params()
and *_output_params() for protecting the concurrent calls. Since
those are exported, it's also meant for hardening from the external
calls, too.
Link: https://lore.kernel.org/r/20220617144051.18985-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Having a lock in snd_rawmidi_runtime can be a problem especially when
a substream is accessed from the outside, as the runtime creation
might be racy with the external calls. As a first step for hardening,
move the spinlock from snd_rawmidi_runtime to snd_rawmidi_substream.
This patch just replaces the lock calls, no real functional change is
put yet.
Link: https://lore.kernel.org/r/20220617144051.18985-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
