| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
When ->init() fails, ->destroy() is called to clean up.
So it is unnecessary to clean up in red_init(), and it
would cause some refcount underflow.
Fixes: aee9caa03fc3 ("net: sched: sch_red: Add qevents "early_drop" and "mark"")
Reported-and-tested-by: syzbot+b33c1cb0a30ebdc8a5f9@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+e5ea5f8a3ecfd4427a1c@syzkaller.appspotmail.com
Cc: Petr Machata <petrm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 9c66d1564676 ("taprio: Add support for hardware
offloading") there's a bit of inconsistency when offloading schedules
to the hardware:
In software mode, the gate masks are specified in terms of traffic
classes, so if say "sched-entry S 03 20000", it means that the traffic
classes 0 and 1 are open for 20us; when taprio is offloaded to
hardware, the gate masks are specified in terms of hardware queues.
The idea here is to fix hardware offloading, so schedules in hardware
and software mode have the same behavior. What's needed to do is to
map traffic classes to queues when applying the offload to the driver.
Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
tcf_ct_handle_fragments() shouldn't free the skb when ip_defrag() call
fails. Otherwise, we will cause a double-free bug.
In such cases, just return the error to the caller.
Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull uninitialized_var() macro removal from Kees Cook:
"This is long overdue, and has hidden too many bugs over the years. The
series has several "by hand" fixes, and then a trivial treewide
replacement.
- Clean up non-trivial uses of uninitialized_var()
- Update documentation and checkpatch for uninitialized_var() removal
- Treewide removal of uninitialized_var()"
* tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
compiler: Remove uninitialized_var() macro
treewide: Remove uninitialized_var() usage
checkpatch: Remove awareness of uninitialized_var() macro
mm/debug_vm_pgtable: Remove uninitialized_var() usage
f2fs: Eliminate usage of uninitialized_var() macro
media: sur40: Remove uninitialized_var() usage
KVM: PPC: Book3S PR: Remove uninitialized_var() usage
clk: spear: Remove uninitialized_var() usage
clk: st: Remove uninitialized_var() usage
spi: davinci: Remove uninitialized_var() usage
ide: Remove uninitialized_var() usage
rtlwifi: rtl8192cu: Remove uninitialized_var() usage
b43: Remove uninitialized_var() usage
drbd: Remove uninitialized_var() usage
x86/mm/numa: Remove uninitialized_var() usage
docs: deprecated.rst: Add uninitialized_var()
|
|
When openvswitch conntrack offload with act_ct action. Fragment packets
defrag in the ingress tc act_ct action and miss the next chain. Then the
packet pass to the openvswitch datapath without the mru. The over
mtu packet will be dropped in output action in openvswitch for over mtu.
"kernel: net2: dropped over-mtu packet: 1528 > 1500"
This patch add mru in the tc_skb_ext for adefrag and miss next chain
situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru
to the qdisc_skb_cb when the packet defrag. And When the chain miss,
The mru is set to tc_skb_ext which can be got by ovs datapath.
Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper, in multiple places, instead
of an open-coded version in order to avoid any potential type
mistakes and protect against potential integer overflows.
Also, remove unnecessary object identifier size.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Exchange the positions of the err_tbl_init and err_register labels in
ct_init_module function.
Fixes: c34b961a2492 ("net/sched: act_ct: Create nf flow table per zone")
Signed-off-by: liujian <liujian56@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure.
This helper offers defense-in-depth against potential integer
overflows, while at the same time makes it explicitly clear that
we are dealing with a flexible array member.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When red_init() fails, red_destroy() is called to clean up.
If the timer is not initialized yet, del_timer_sync() will
complain. So we have to move timer_setup() before any failure.
Reported-and-tested-by: syzbot+6e95a4fabf88dc217145@syzkaller.appspotmail.com
Fixes: aee9caa03fc3 ("net: sched: sch_red: Add qevents "early_drop" and "mark"")
Cc: Petr Machata <petrm@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding new cls flower keys for hash value and hash
mask and dissect the hash info from the skb into
the flow key towards flow classication.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed that touching linux/rhashtable.h causes lib/vsprintf.c to
be rebuilt. This dependency came through a bogus inclusion in the
file net/flow_offload.h. This patch moves it to the right place.
This patch also removes a lingering rhashtable inclusion in cls_api
created by the same commit.
Fixes: 4e481908c51b ("flow_offload: move tc indirect block to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fragment packets do defrag in tcf_ct_handle_fragments
will clear the skb->cb which make the qdisc_skb_cb clear
too. So the qdsic_skb_cb should be store before defrag and
restore after that.
It also update the pkt_len after all the
fragments finish the defrag to one packet and make the
following actions counter correct.
Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the qdisc_match_from_root function() is called from non-rcu path
with rtnl mutex held, a suspiciout rcu usage warning appears:
[ 241.504354] =============================
[ 241.504358] WARNING: suspicious RCU usage
[ 241.504366] 5.8.0-rc4-custom-01521-g72a7c7d549c3 #32 Not tainted
[ 241.504370] -----------------------------
[ 241.504378] net/sched/sch_api.c:270 RCU-list traversed in non-reader section!!
[ 241.504382]
other info that might help us debug this:
[ 241.504388]
rcu_scheduler_active = 2, debug_locks = 1
[ 241.504394] 1 lock held by tc/1391:
[ 241.504398] #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0
[ 241.504431]
stack backtrace:
[ 241.504440] CPU: 0 PID: 1391 Comm: tc Not tainted 5.8.0-rc4-custom-01521-g72a7c7d549c3 #32
[ 241.504446] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
[ 241.504453] Call Trace:
[ 241.504465] dump_stack+0x100/0x184
[ 241.504482] lockdep_rcu_suspicious+0x153/0x15d
[ 241.504499] qdisc_match_from_root+0x293/0x350
Fix this by passing the rtnl held lockdep condition down to
hlist_for_each_entry_rcu()
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit aebe4426ccaa4838f36ea805cdf7d76503e65117.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mirred currently does not mix well with blocks executed after the qdisc
root lock is taken. This includes classification blocks (such as in PRIO,
ETS, DRR qdiscs) and qevents. The locking caused by the packet mirrored by
mirred can cause deadlocks: either when the thread of execution attempts to
take the lock a second time, or when two threads end up waiting on each
other's locks.
The qevent patchset attempted to not introduce further badness of this
sort, and dropped the lock before executing the qevent block. However this
lead to too little locking and races between qdisc configuration and packet
enqueue in the RED qdisc.
Before the deadlock issues are solved in a way that can be applied across
many qdiscs reasonably easily, do for qevents what is done for the
classification blocks and just keep holding the root lock.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simple fixes which require no deep knowledge of the code.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tcf_block_get() fails inside atm_tc_init(),
atm_tc_put() is called to release the qdisc p->link.q.
But the flow->ref prevents it to do so, as the flow->ref
is still zero.
Fix this by moving the p->link.ref initialization before
tcf_block_get().
Fixes: 6529eaba33f0 ("net: sched: introduce tcf block infractructure")
Reported-and-tested-by: syzbot+d411cff6ab29cc2c311b@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tcf_ct_act execute the tcf_lastuse_update should
be update or the used stats never update
filter protocol ip pref 3 flower chain 0
filter protocol ip pref 3 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 1.1.1.1
ip_flags frag/firstfrag
skip_hw
not_in_hw
action order 1: ct zone 1 nat pipe
index 1 ref 1 bind 1 installed 103 sec used 103 sec
Action statistics:
Sent 151500 bytes 101 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
cookie 4519c04dc64a1a295787aab13b6a50fb
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a couple of places in net/sched/ that check skb->protocol and act
on the value there. However, in the presence of VLAN tags, the value stored
in skb->protocol can be inconsistent based on whether VLAN acceleration is
enabled. The commit quoted in the Fixes tag below fixed the users of
skb->protocol to use a helper that will always see the VLAN ethertype.
However, most of the callers don't actually handle the VLAN ethertype, but
expect to find the IP header type in the protocol field. This means that
things like changing the ECN field, or parsing diffserv values, stops
working if there's a VLAN tag, or if there are multiple nested VLAN
tags (QinQ).
To fix this, change the helper to take an argument that indicates whether
the caller wants to skip the VLAN tags or not. When skipping VLAN tags, we
make sure to skip all of them, so behaviour is consistent even in QinQ
mode.
To make the helper usable from the ECN code, move it to if_vlan.h instead
of pkt_sched.h.
v3:
- Remove empty lines
- Move vlan variable definitions inside loop in skb_protocol()
- Also use skb_protocol() helper in IP{,6}_ECN_decapsulate() and
bpf_skb_ecn_set_ce()
v2:
- Use eth_type_vlan() helper in skb_protocol()
- Also fix code that reads skb->protocol directly
- Change a couple of 'if/else if' statements to switch constructs to avoid
calling the helper twice
Reported-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
Fixes: d8b9605d2697 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to fq_codel and the other qdiscs that can set as default,
fq_pie is also suitable for general use without explicit configuration,
which makes it a valid choice for this.
This is useful in situations where a painless out-of-the-box solution
for reducing bufferbloat is desired but fq_codel is not necessarily the
best choice. For example, fq_pie can be better for DASH streaming, but
there could be more cases where it's the better choice of the two simple
AQMs available in the kernel.
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to allow acting on dropped and/or ECN-marked packets, add two new
qevents to the RED qdisc: "early_drop" and "mark". Filters attached at
"early_drop" block are executed as packets are early-dropped, those
attached at the "mark" block are executed as packets are ECN-marked.
Two new attributes are introduced: TCA_RED_EARLY_DROP_BLOCK with the block
index for the "early_drop" qevent, and TCA_RED_MARK_BLOCK for the "mark"
qevent. Absence of these attributes signifies "don't care": no block is
allocated in that case, or the existing blocks are left intact in case of
the change callback.
For purposes of offloading, blocks attached to these qevents appear with
newly-introduced binder types, FLOW_BLOCK_BINDER_TYPE_RED_EARLY_DROP and
FLOW_BLOCK_BINDER_TYPE_RED_MARK.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the following patches, RED will get two qevents. The implementation will
be clearer if the callback for change is not a pure subset of the callback
for init. Split the two and promote attribute parsing to the callbacks
themselves from the common code, because it will be handy there.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qevents are attach points for TC blocks, where filters can be put that are
executed when "interesting events" take place in a qdisc. The data to keep
and the functions to invoke to maintain a qevent will be largely the same
between qevents. Therefore introduce sched-wide helpers for qevent
management.
Currently, similarly to ingress and egress blocks of clsact pseudo-qdisc,
blocks attachment cannot be changed after the qdisc is created. To that
end, add a helper tcf_qevent_validate_change(), which verifies whether
block index attribute is not attached, or if it is, whether its value
matches the current one (i.e. there is no material change).
The function tcf_qevent_handle() should be invoked when qdisc hits the
"interesting event" corresponding to a block. This function releases root
lock for the duration of executing the attached filters, to allow packets
generated through user actions (notably mirred) to be reinserted to the
same qdisc tree.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A following patch introduces qevents, points in qdisc algorithm where
packet can be processed by user-defined filters. Should this processing
lead to a situation where a new packet is to be enqueued on the same port,
holding the root lock would lead to deadlocks. To solve the issue, qevent
handler needs to unlock and relock the root lock when necessary.
To that end, add the root lock argument to the qdisc op enqueue, and
propagate throughout.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change tin mapping on diffserv3, 4 & 8 for LE PHB support, in essence
making LE a member of the Bulk tin.
Bulk has the least priority and minimum of 1/16th total bandwidth in the
face of higher priority traffic.
NB: Diffserv 3 & 4 swap tin 0 & 1 priorities from the default order as
found in diffserv8, in case anyone is wondering why it looks a bit odd.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[ reword commit message slightly ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I spotted a few nits when comparing the in-tree version of sch_cake with
the out-of-tree one: A redundant error variable declaration shadowing an
outer declaration, and an indentation alignment issue. Fix both of these.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a further optimisation of the diffserv parsing codepath, we can skip it
entirely if CAKE is configured to neither use diffserv-based
classification, nor to zero out the diffserv bits.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cake_handle_diffserv() tries to linearize mac and network header parts of
skb and to make it writable unconditionally. In some cases it leads to full
skb reallocation, which reduces throughput and increases CPU load. Some
measurements of IPv4 forward + NAPT on MIPS router with 580 MHz single-core
CPU was conducted. It appears that on kernel 4.9 skb_try_make_writable()
reallocates skb, if skb was allocated in ethernet driver via so-called
'build skb' method from page cache (it was discovered by strange increase
of kmalloc-2048 slab at first).
Obtain DSCP value via read-only skb_header_pointer() call, and leave
linearization only for DSCP bleaching or ECN CE setting. And, as an
additional optimisation, skip diffserv parsing entirely if it is not needed
by the current configuration.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits")
Signed-off-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
[ fix a few style issues, reflow commit message ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware device may include more than one police entry. Specifying the
action's index make it possible for several tc filters to share the same
police action when installing the filters.
Propagate this index to device drivers through the flow offload
intermediate representation, so that drivers could share a single
hardware policer between multiple filters.
v1->v2 changes:
- Update the commit message suggest by Ido Schimmel <idosch@idosch.org>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current police offloading support the 'burst'' and 'rate_bytes_ps'. Some
hardware own the capability to limit the frame size. If the frame size
larger than the setting, the frame would be dropped. For the police
action itself already accept the 'mtu' parameter in tc command. But not
extend to tc flower offloading. So extend 'mtu' to tc flower offloading.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arg cannot be NULL since its already being dereferenced
before. Remove the redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The user tool modinfo is used to get information on kernel modules, including a
description where it is available.
This patch adds a brief MODULE_DESCRIPTION to the following modules:
9p
drop_monitor
esp4_offload
esp6_offload
fou
fou6
ila
sch_fq
sch_fq_codel
sch_hhf
Signed-off-by: Rob Gill <rrobgill@protonmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the redundant null check for skb.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
parent cannot be NULL here since its in the else part
of the if (parent == NULL) condition. Remove the extra
check on parent pointer.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
variable _size_.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The block->nooffloaddevcnt should always count for indr block.
even the indr block offload successful. The representor maybe
gone away and the ingress qdisc can work in software mode.
block->nooffloaddevcnt warning with following dmesg log:
[ 760.667058] #####################################################
[ 760.668186] ## TEST test-ecmp-add-vxlan-encap-disable-sriov.sh ##
[ 760.669179] #####################################################
[ 761.780655] :test: Fedora 30 (Thirty)
[ 761.783794] :test: Linux reg-r-vrt-018-180 5.7.0+
[ 761.822890] :test: NIC ens1f0 FW 16.26.6000 PCI 0000:81:00.0 DEVICE 0x1019 ConnectX-5 Ex
[ 761.860244] mlx5_core 0000:81:00.0 ens1f0: Link up
[ 761.880693] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready
[ 762.059732] mlx5_core 0000:81:00.1 ens1f1: Link up
[ 762.234341] :test: unbind vfs of ens1f0
[ 762.257825] :test: Change ens1f0 eswitch (0000:81:00.0) mode to switchdev
[ 762.291363] :test: unbind vfs of ens1f1
[ 762.306914] :test: Change ens1f1 eswitch (0000:81:00.1) mode to switchdev
[ 762.309237] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(LEGACY), nvfs(2), active vports(3)
[ 763.282598] mlx5_core 0000:81:00.1: E-Switch: Supported tc offload range - chains: 4294967294, prios: 4294967295
[ 763.362825] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[ 763.444465] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0
[ 763.460088] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[ 763.502586] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[ 763.552429] ens1f1_0: renamed from eth0
[ 763.569569] mlx5_core 0000:81:00.1: E-Switch: Enable: mode(OFFLOADS), nvfs(2), active vports(3)
[ 763.629694] ens1f1_1: renamed from eth1
[ 764.631552] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_0: link becomes ready
[ 764.670841] :test: unbind vfs of ens1f0
[ 764.681966] :test: unbind vfs of ens1f1
[ 764.726762] mlx5_core 0000:81:00.0 ens1f0: Link up
[ 764.766511] mlx5_core 0000:81:00.1 ens1f1: Link up
[ 764.797325] :test: Add multipath vxlan encap rule and disable sriov
[ 764.798544] :test: config multipath route
[ 764.812732] mlx5_core 0000:81:00.0: lag map port 1:2 port 2:2
[ 764.874556] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:2
[ 765.603681] :test: OK
[ 765.659048] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_1: link becomes ready
[ 765.675085] :test: verify rule in hw
[ 765.694237] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready
[ 765.711892] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1: link becomes ready
[ 766.979230] :test: OK
[ 768.125419] :test: OK
[ 768.127519] :test: - disable sriov ens1f1
[ 768.131160] pci 0000:81:02.2: Removing from iommu group 75
[ 768.132646] pci 0000:81:02.3: Removing from iommu group 76
[ 769.179749] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3)
[ 769.455627] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:1
[ 769.703990] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[ 769.988637] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0
[ 769.990022] :test: - disable sriov ens1f0
[ 769.994922] pci 0000:81:00.2: Removing from iommu group 73
[ 769.997048] pci 0000:81:00.3: Removing from iommu group 74
[ 771.035813] mlx5_core 0000:81:00.0: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3)
[ 771.339091] ------------[ cut here ]------------
[ 771.340812] WARNING: CPU: 6 PID: 3448 at net/sched/cls_api.c:749 tcf_block_offload_unbind.isra.0+0x5c/0x60
[ 771.341728] Modules linked in: act_mirred act_tunnel_key cls_flower dummy vxlan ip6_udp_tunnel udp_tunnel sch_ingress nfsv3 nfs_acl nfs lockd grace fscache tun bridge stp llc sunrpc rdma_ucm rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp mlxfw act_ct nf_flow_table kvm_intel nf_nat kvm nf_conntrack irqbypass crct10dif_pclmul igb crc32_pclmul nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 crc32c_intel ghash_clmulni_intel ptp ipmi_ssif intel_cstate pps_c
ore ses intel_uncore mei_me iTCO_wdt joydev ipmi_si iTCO_vendor_support i2c_i801 enclosure mei ioatdma dca lpc_ich wmi ipmi_devintf pcspkr acpi_power_meter ipmi_msghandler acpi_pad ast i2c_algo_bit drm_vram_helper drm_kms_helper drm_ttm_helper ttm drm mpt3sas raid_class scsi_transport_sas
[ 771.347818] CPU: 6 PID: 3448 Comm: test-ecmp-add-v Not tainted 5.7.0+ #1146
[ 771.348727] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 771.349646] RIP: 0010:tcf_block_offload_unbind.isra.0+0x5c/0x60
[ 771.350553] Code: 4a fd ff ff 83 f8 a1 74 0e 5b 4c 89 e7 5d 41 5c 41 5d e9 07 93 89 ff 8b 83 a0 00 00 00 8d 50 ff 89 93 a0 00 00 00 85 c0 75 df <0f> 0b eb db 0f 1f 44 00 00 41 57 41 56 41 55 41 89 cd 41 54 49 89
[ 771.352420] RSP: 0018:ffffb33144cd3b00 EFLAGS: 00010246
[ 771.353353] RAX: 0000000000000000 RBX: ffff8b37cf4b2800 RCX: 0000000000000000
[ 771.354294] RDX: 00000000ffffffff RSI: ffff8b3b9aad0000 RDI: ffffffff8d5c6e20
[ 771.355245] RBP: ffff8b37eb546948 R08: ffffffffc0b7a348 R09: ffff8b3b9aad0000
[ 771.356189] R10: 0000000000000001 R11: ffff8b3ba7a0a1c0 R12: ffff8b37cf4b2850
[ 771.357123] R13: ffff8b3b9aad0000 R14: ffff8b37cf4b2820 R15: ffff8b37cf4b2820
[ 771.358039] FS: 00007f8a19b6e740(0000) GS:ffff8b3befa00000(0000) knlGS:0000000000000000
[ 771.358965] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 771.359885] CR2: 00007f3afb91c1a0 CR3: 000000045133c004 CR4: 00000000001606e0
[ 771.360825] Call Trace:
[ 771.361764] __tcf_block_put+0x84/0x150
[ 771.362712] ingress_destroy+0x1b/0x20 [sch_ingress]
[ 771.363658] qdisc_destroy+0x3e/0xc0
[ 771.364594] dev_shutdown+0x7a/0xa5
[ 771.365522] rollback_registered_many+0x20d/0x530
[ 771.366458] ? netdev_upper_dev_unlink+0x15d/0x1c0
[ 771.367387] unregister_netdevice_many.part.0+0xf/0x70
[ 771.368310] vxlan_netdevice_event+0xa4/0x110 [vxlan]
[ 771.369454] notifier_call_chain+0x4c/0x70
[ 771.370579] rollback_registered_many+0x2f5/0x530
[ 771.371719] rollback_registered+0x56/0x90
[ 771.372843] unregister_netdevice_queue+0x73/0xb0
[ 771.373982] unregister_netdev+0x18/0x20
[ 771.375168] mlx5e_vport_rep_unload+0x56/0xc0 [mlx5_core]
[ 771.376327] esw_offloads_disable+0x81/0x90 [mlx5_core]
[ 771.377512] mlx5_eswitch_disable_locked.cold+0xcb/0x1af [mlx5_core]
[ 771.378679] mlx5_eswitch_disable+0x44/0x60 [mlx5_core]
[ 771.379822] mlx5_device_disable_sriov+0xad/0xb0 [mlx5_core]
[ 771.380968] mlx5_core_sriov_configure+0xc1/0xe0 [mlx5_core]
[ 771.382087] sriov_numvfs_store+0xfc/0x130
[ 771.383195] kernfs_fop_write+0xce/0x1b0
[ 771.384302] vfs_write+0xb6/0x1a0
[ 771.385410] ksys_write+0x5f/0xe0
[ 771.386500] do_syscall_64+0x5b/0x1d0
[ 771.387569] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 0fdcf78d5973 ("net: use flow_indr_dev_setup_offload()")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path.
Fixes: 1fac52da5942 ("net: flow_offload: consolidate indirect flow_block infrastructure")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
