| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic connection tracking support for the bridge,
including initial IPv4 support.
This patch register two hooks to deal with the bridge forwarding path,
one from the bridge prerouting hook to call nf_conntrack_in(); and
another from the bridge postrouting hook to confirm the entry.
The conntrack bridge prerouting hook defragments packets before passing
them to nf_conntrack_in() to look up for an existing entry, otherwise a
new entry is allocated and it is attached to the skbuff. The conntrack
bridge postrouting hook confirms new conntrack entries, ie. if this is
the first packet seen, then it adds the entry to the hashtable and (if
needed) it refragments the skbuff into the original fragments, leaving
the geometry as is if possible. Exceptions are linearized skbuffs, eg.
skbuffs that are passed up to nfqueue and conntrack helpers, as well as
cloned skbuff for the local delivery (eg. tcpdump), also in case of
bridge port flooding (cloned skbuff too).
The packet defragmentation is done through the ip_defrag() call. This
forces us to save the bridge control buffer, reset the IP control buffer
area and then restore it after call. This function also bumps the IP
fragmentation statistics, it would be probably desiderable to have
independent statistics for the bridge defragmentation/refragmentation.
The maximum fragment length is stored in the control buffer and it is
used to refragment the skbuff from the postrouting path.
The new fraglist splitter and fragment transformer APIs are used to
implement the bridge refragmentation code. The br_ip_fragment() function
drops the packet in case the maximum fragment size seen is larger than
the output port MTU.
This patchset follows the principle that conntrack should not drop
packets, so users can do it through policy via invalid state matching.
Like br_netfilter, there is no refragmentation for packets that are
passed up for local delivery, ie. prerouting -> input path. There are
calls to nf_reset() already in several spots in the stack since time ago
already, eg. af_packet, that show that skbuff fraglist handling from the
netif_rx path is supported already.
The helpers are called from the postrouting hook, before confirmation,
from there we may see packet floods to bridge ports. Then, although
unlikely, this may result in exercising the helpers many times for each
clone. It would be good to explore how to pass all the packets in a list
to the conntrack hook to do this handle only once for this case.
Thanks to Florian Westphal for handing me over an initial patchset
version to add support for conntrack bridge.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the case of vlan filtering on bridges, the bridge may also have the
corresponding vlan devices as upper devices. A vlan bridge binding mode
is added to allow the link state of the vlan device to track only the
state of the subset of bridge ports that are also members of the vlan,
rather than that of all bridge ports. This mode is set with a vlan flag
rather than a bridge sysfs so that the 8021q module is aware that it
should not set the link state for the vlan device.
If bridge vlan is configured, the bridge device event handling results
in the link state for an upper device being set, if it is a vlan device
with the vlan bridge binding mode enabled. This also sets a
vlan_bridge_binding flag so that subsequent UP/DOWN/CHANGE events for
the ports in that bridge result in a link state update of the vlan
device if required.
The link state of the vlan device is up if there is at least one bridge
port that is a vlan member that is admin & oper up, otherwise its oper
state is IF_OPER_LOWERLAYERDOWN.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes broute a normal ebtables table, hooking at PREROUTING.
The broute hook is removed.
It uses skb->cb to signal to bridge rx handler that the skb should be
routed instead of being bridged.
This change is backwards compatible with ebtables as no userspace visible
parts are changed.
This means we can also remove the !ops test in ebt_register_table,
it was only there for broute table sake.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Reduce size of br_input_skb_cb from 24 to 16 bytes by
using bitfield for those values that can only be 0 or 1.
igmp is the igmp type value, so it needs to be at least u8.
Furthermore, the bridge currently relies on step-by-step initialization
of br_input_skb_cb fields as the skb passes through the stack.
Explicitly zero out the bridge input cb instead, this avoids having to
review/validate that no BR_INPUT_SKB_CB(skb)->foo test can see a
'random' value from previous protocol cb.
AFAICS all current fields are always set up before they are read again,
so this is not a bug fix.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Replace the br_port_exists() macro with its twin from netdevice.h
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding / deleting VLANs to / from a bridge port, the bridge driver
first tries to propagate the information via switchdev and falls back to
the 8021q driver in case the underlying driver does not support
switchdev. This can result in a memory leak [1] when VXLAN and mlxsw
ports are enslaved to the bridge:
$ ip link set dev vxlan0 master br0
# No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev
# notification and the bridge driver adds the VLAN on 'vxlan0' via the
# 8021q driver
$ bridge vlan add vid 10 dev vxlan0 pvid untagged
# mlxsw port is enslaved to the bridge
$ ip link set dev swp1 master br0
# mlxsw processes the switchdev notification and the 8021q driver is
# skipped
$ bridge vlan del vid 10 dev vxlan0
This results in 'struct vlan_info' and 'struct vlan_vid_info' being
leaked, as they were allocated by the 8021q driver during VLAN addition,
but never freed as the 8021q driver was skipped during deletion.
Fix this by introducing a new VLAN private flag that indicates whether
the VLAN was added on the port by switchdev or the 8021q driver. If the
VLAN was added by the 8021q driver, then we make sure to delete it via
the 8021q driver as well.
[1]
unreferenced object 0xffff88822d20b1e8 (size 256):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s)
hex dump (first 32 bytes):
e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<00000000e0178b02>] vlan_vid_add+0x661/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
unreferenced object 0xffff888227454308 (size 32):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s)
hex dump (first 32 bytes):
88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -....
81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<0000000018050631>] vlan_vid_add+0x3e6/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bridge's default hash_max was 512 which is rather conservative, now that
we're using the generic rhashtable API which autoshrinks let's increase
it to 4096 and move it to a define in br_private.h.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the bridge multicast uses the generic rhashtable interface we
can drop the hash_elasticity option as that is already done for us and
it's hardcoded to a maximum of RHT_ELASTICITY (16 currently). Add a
warning about the obsolete option when the hash_elasticity is set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bridge multicast code has been using a mix of RCU and RCU-bh flavors
sometimes in questionable way. Since we've moved to rhashtable just use
non-bh RCU everywhere. In addition this simplifies freeing of objects
and allows us to remove some unnecessary callback functions.
v3: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bridge multicast code currently uses a custom resizable hashtable
which predates the generic rhashtable interface. It has many
shortcomings compared and duplicates functionality that is presently
available via the generic rhashtable, so this patch removes the custom
rhashtable implementation in favor of the kernel's generic rhashtable.
The hash maximum is kept and the rhashtable's size is used to do a loose
check if it's reached in which case we revert to the old behaviour and
disable further bridge multicast processing. Also now we can support any
hash maximum, doesn't need to be a power of 2.
v3: add non-rcu br_mdb_get variant and use it where multicast_lock is
held to avoid RCU splat, drop hash_max function and just set it
directly
v2: handle when IGMP snooping is undefined, add br_mdb_init/uninit
placeholders
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new boolopt API to add an option which disables learning from
link-local packets. The default is kept as before and learning is
enabled. This is a simple map from a boolopt bit to a bridge private
flag that is tested before learning.
v2: pass NULL for extack via sysfs
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have been adding many new bridge options, a big number of which are
boolean but still take up netlink attribute ids and waste space in the skb.
Recently we discussed learning from link-local packets[1] and decided
yet another new boolean option will be needed, thus introducing this API
to save some bridge nl space.
The API supports changing the value of multiple boolean options at once
via the br_boolopt_multi struct which has an optmask (which options to
set, bit per opt) and optval (options' new values). Future boolean
options will only be added to the br_boolopt_id enum and then will have
to be handled in br_boolopt_toggle/get. The API will automatically
add the ability to change and export them via netlink, sysfs can use the
single boolopt function versions to do the same. The behaviour with
failing/succeeding is the same as with normal netlink option changing.
If an option requires mapping to internal kernel flag or needs special
configuration to be enabled then it should be handled in
br_boolopt_toggle. It should also be able to retrieve an option's current
state via br_boolopt_get.
v2: WARN_ON() on unsupported option as that shouldn't be possible and
also will help catch people who add new options without handling
them for both set and get. Pass down extack so if an option desires
it could set it on error and be more user-friendly.
[1] https://www.spinics.net/lists/netdev/msg532698.html
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f0c ("net: bridge: add support for per-port vlan stats")
Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes assumption than vlan_tci != 0 when tag is present.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Further reduce the size of net_bridge with 8 bytes and reduce the number of
holes in it:
Before: holes: 5, sum holes: 15
After: holes: 3, sum holes: 7
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the last remaining bool option to a bit thus reducing the overall
net_bridge size further by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the neigh_suppress_enabled option to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts the rest of the mcast options to bits. It also packs
the mcast options a little better by moving multicast_mld_version to an
existing hole, reducing the net_bridge size by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert mcast disabled to an option bit and while doing so convert the
logic to check if multicast is enabled instead. That is make the logic
follow the option value - if it's set then mcast is enabled and vice versa.
This avoids a few confusing places where we inverted the value that's being
set to follow the mcast_disabled logic.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert group_addr_set internal bridge opt to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No functional change, convert of nf_call_[ip|ip6|arp]tables to bits.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge options have usually been added as separate fields all over the
net_bridge struct taking up space and ending up in different cache lines.
Let's move them to a single bitfield to save up space and speedup lookups.
This patch adds a simple API for option modifying and retrieving using
bitops and converts the first user of the API - the bridge vlan options
(vlan_enabled and vlan_stats_enabled).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we have a mix of opening brackets on new lines and on the same
line, let's move them all on the same line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for entries which are "sticky", i.e. will not change their port
if they show up from a different one. A new ndm flag is introduced for that
purpose - NTF_STICKY. We allow to set it only to non-local entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating various bridge objects in /sys/class/net/... make sure
that they belong to the container's owner instead of global root (if
they belong to a container/namespace).
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A call to switchdev_port_obj_add() or switchdev_port_obj_del() involves
initializing a struct switchdev_obj_port_vlan, a piece of code that
repeats on each call site almost verbatim. While in the current codebase
there is just one duplicated add call, the follow-up patches add more of
both add and del calls.
Thus to remove the duplication, extract the repetition into named
functions and reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not automatically bail out on sending notifications about activity on
non-user-added FDB entries. Instead, notify about this activity except
for cases where the activity itself originates in a notification, to
avoid sending duplicate notifications.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While handling netdevice events, br_device_event() sometimes uses
br_stp_(disable|enable)_port which unconditionally send a notification,
but then a second notification for the same event is sent at the end of
the br_device_event() function. To avoid sending duplicate notifications
in such cases, check if one has already been sent (i.e.
br_stp_enable/disable_port have been called).
The patch is based on a change by Satish Ashok.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a couple new functions to allow querying FDB and vlan settings of a
bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Roopa noted today the biggest source of problems when configuring
bridge and ports is that the bridge MTU keeps changing automatically on
port events (add/del/changemtu). That leads to inconsistent behaviour
and network config software needs to chase the MTU and fix it on each
such event. Let's improve on that situation and allow for the user to
set any MTU within ETH_MIN/MAX limits, but once manually configured it
is the user's responsibility to keep it correct afterwards.
In case the MTU isn't manually set - the behaviour reverts to the
previous and the bridge follows the minimum MTU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently the bridge was changed to automatically set maximum MTU on port
events (add/del/changemtu) when vlan filtering is enabled, but that
actually changes behaviour in a way which breaks some setups and can lead
to packet drops. In order to still allow that maximum to be set while being
compatible, we add the ability for the user to tune the bridge MTU up to
the maximum when vlan filtering is enabled, but that has to be done
explicitly and all port events (add/del/changemtu) lead to resetting that
MTU to the minimum as before.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the bridge is allowing multiple VLANs, some VLANs may have
different MTUs. Instead of choosing the minimum MTU for the
bridge interface, choose the maximum MTU of the bridge members.
With this the user only needs to set a larger MTU on the member
ports that are participating in the large MTU VLANS.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return statements in functions returning bool should use
true/false instead of 1/0.
This issue was detected with the help of Coccinelle.
Fixes: 85b352693264 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch the bridge used a fixed 256 element hash table which
was fine for small use cases (in my tests it starts to degrade
above 1000 entries), but it wasn't enough for medium or large
scale deployments. Modern setups have thousands of participants in a
single bridge, even only enabling vlans and adding a few thousand vlan
entries will cause a few thousand fdbs to be automatically inserted per
participating port. So we need to scale the fdb table considerably to
cope with modern workloads, and this patch converts it to use a
rhashtable for its operations thus improving the bridge scalability.
Tests show the following results (10 runs each), at up to 1000 entries
rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it
is 2 times faster and at 30000 it is 50 times faster.
Obviously this happens because of the properties of the two constructs
and is expected, rhashtable keeps pretty much a constant time even with
10000000 entries (tested), while the fixed hash table struggles
considerably even above 10000.
As a side effect this also reduces the net_bridge struct size from 3248
bytes to 1344 bytes. Also note that the key struct is 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The boolean mglist indicates the host has joined a particular
multicast group on the bridge interface. It is badly named, obscuring
what is means. Rename it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
