| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 8651f97bd951 ("PM / cpuidle: System resume hang fix with
cpuidle") that introduced cpuidle pausing during system suspend
did that to work around a platform firmware issue causing systems
to hang during resume if CPUs were allowed to enter idle states
in the system suspend and resume code paths.
However, pausing cpuidle before the last phase of suspending
devices is the source of an otherwise arbitrary difference between
the suspend-to-idle path and other system suspend variants, so it is
cleaner to do that later, before taking secondary CPUs offline (it
is still safer to take secondary CPUs offline with cpuidle paused,
though).
Modify the code accordingly, but in order to avoid code duplication,
introduce new wrapper functions, pm_sleep_disable_secondary_cpus()
and pm_sleep_enable_secondary_cpus(), to combine cpuidle_pause()
and cpuidle_resume(), respectively, with the handling of secondary
CPUs during system-wide transitions to sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is unsafe to allow saving of secretmem areas to the hibernation
snapshot as they would be visible after the resume and this essentially
will defeat the purpose of secret memory mappings.
Prevent hibernation whenever there are active secret memory users.
Link: https://lkml.kernel.org/r/20210518072034.31572-6-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tycho Andersen <tycho@tycho.ws>
Cc: Will Deacon <will@kernel.org>
Cc: kernel test robot <lkp@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Page poisoning used to be incompatible with hibernation, as the state of
poisoned pages was lost after resume, thus enabling CONFIG_HIBERNATION
forces CONFIG_PAGE_POISONING_NO_SANITY. For the same reason, the
poisoning with zeroes variant CONFIG_PAGE_POISONING_ZERO used to disable
hibernation. The latter restriction was removed by commit 1ad1410f632d
("PM / Hibernate: allow hibernation with PAGE_POISONING_ZERO") and
similarly for init_on_free by commit 18451f9f9e58 ("PM: hibernate: fix
crashes with init_on_free=1") by making sure free pages are cleared after
resume.
We can use the same mechanism to instead poison free pages with
PAGE_POISON after resume. This covers both zero and 0xAA patterns. Thus
we can remove the Kconfig restriction that disables page poison sanity
checking when hibernation is enabled.
Link: https://lkml.kernel.org/r/20201113104033.22907-4-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [hibernation]
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@kernel.org>
Cc: Mateusz Nosek <mateusznosek0@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the collection of cpufreq statistics to allow it to take
place if fast frequency switching is enabled in the governor, rework
the frequency invariance handling in the cpufreq core and drivers, add
new hardware support to a couple of cpufreq drivers, fix a number of
assorted issues and clean up the code all over.
Specifics:
- Rework cpufreq statistics collection to allow it to take place when
fast frequency switching is enabled in the governor (Viresh Kumar).
- Make the cpufreq core set the frequency scale on behalf of the
driver and update several cpufreq drivers accordingly (Ionela
Voinescu, Valentin Schneider).
- Add new hardware support to the STI and qcom cpufreq drivers and
improve them (Alain Volmat, Manivannan Sadhasivam).
- Fix multiple assorted issues in cpufreq drivers (Jon Hunter,
Krzysztof Kozlowski, Matthias Kaehlcke, Pali Rohár, Stephan
Gerhold, Viresh Kumar).
- Fix several assorted issues in the operating performance points
(OPP) framework (Stephan Gerhold, Viresh Kumar).
- Allow devfreq drivers to fetch devfreq instances by DT enumeration
instead of using explicit phandles and modify the devfreq core code
to support driver-specific devfreq DT bindings (Leonard Crestez,
Chanwoo Choi).
- Improve initial hardware resetting in the tegra30 devfreq driver
and clean up the tegra cpuidle driver (Dmitry Osipenko).
- Update the cpuidle core to collect state entry rejection statistics
and expose them via sysfs (Lina Iyer).
- Improve the ACPI _CST code handling diagnostics (Chen Yu).
- Update the PSCI cpuidle driver to allow the PM domain
initialization to occur in the OSI mode as well as in the PC mode
(Ulf Hansson).
- Rework the generic power domains (genpd) core code to allow domain
power off transition to be aborted in the absence of the "power
off" domain callback (Ulf Hansson).
- Fix two suspend-to-idle issues in the ACPI EC driver (Rafael
Wysocki).
- Fix the handling of timer_expires in the PM-runtime framework on
32-bit systems and the handling of device links in it (Grygorii
Strashko, Xiang Chen).
- Add IO requests batching support to the hibernate image saving and
reading code and drop a bogus get_gendisk() from there (Xiaoyi
Chen, Christoph Hellwig).
- Allow PCIe ports to be put into the D3cold power state if they are
power-manageable via ACPI (Lukas Wunner).
- Add missing header file include to a power capping driver (Pujin
Shi).
- Clean up the qcom-cpr AVS driver a bit (Liu Shixin).
- Kevin Hilman steps down as designated reviwer of adaptive voltage
scaling (AVS) drivers (Kevin Hilman)"
* tag 'pm-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
cpufreq: stats: Fix string format specifier mismatch
arm: disable frequency invariance for CONFIG_BL_SWITCHER
cpufreq,arm,arm64: restructure definitions of arch_set_freq_scale()
cpufreq: stats: Add memory barrier to store_reset()
cpufreq: schedutil: Simplify sugov_fast_switch()
ACPI: EC: PM: Drop ec_no_wakeup check from acpi_ec_dispatch_gpe()
ACPI: EC: PM: Flush EC work unconditionally after wakeup
PCI/ACPI: Whitelist hotplug ports for D3 if power managed by ACPI
PM: hibernate: remove the bogus call to get_gendisk() in software_resume()
cpufreq: Move traces and update to policy->cur to cpufreq core
cpufreq: stats: Enable stats for fast-switch as well
cpufreq: stats: Mark few conditionals with unlikely()
cpufreq: stats: Remove locking
cpufreq: stats: Defer stats update to cpufreq_stats_record_transition()
PM: domains: Allow to abort power off when no ->power_off() callback
PM: domains: Rename power state enums for genpd
PM / devfreq: tegra30: Improve initial hardware resetting
PM / devfreq: event: Change prototype of devfreq_event_get_edev_by_phandle function
PM / devfreq: Change prototype of devfreq_get_devfreq_by_phandle function
PM / devfreq: Add devfreq_get_devfreq_by_node function
...
|
|
get_gendisk grabs a reference on the disk and file operation, so this
code will leak both of them while having absolutely no use for the
gendisk itself.
This effectively reverts commit 2df83fa4bce421f ("PM / Hibernate: Use
get_gendisk to verify partition if resume_file is integer format")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current notifiers have the following error handling pattern all
over the place:
int err, nr;
err = __foo_notifier_call_chain(&chain, val_up, v, -1, &nr);
if (err & NOTIFIER_STOP_MASK)
__foo_notifier_call_chain(&chain, val_down, v, nr-1, NULL)
And aside from the endless repetition thereof, it is broken. Consider
blocking notifiers; both calls take and drop the rwsem, this means
that the notifier list can change in between the two calls, making @nr
meaningless.
Fix this by replacing all the __foo_notifier_call_chain() functions
with foo_notifier_call_chain_robust() that embeds the above pattern,
but ensures it is inside a single lock region.
Note: I switched atomic_notifier_call_chain_robust() to use
the spinlock, since RCU cannot provide the guarantee
required for the recovery.
Note: software_resume() error handling was broken afaict.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200818135804.325626653@infradead.org
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updayes from Vishal Verma:
"You'd normally receive this pull request from Dan Williams, but he's
busy watching a newborn (Congrats Dan!), so I'm watching libnvdimm
this cycle.
This adds a new feature in libnvdimm - 'Runtime Firmware Activation',
and a few small cleanups and fixes in libnvdimm and DAX. I'd
originally intended to make separate topic-based pull requests - one
for libnvdimm, and one for DAX, but some of the DAX material fell out
since it wasn't quite ready.
Summary:
- add 'Runtime Firmware Activation' support for NVDIMMs that
advertise the relevant capability
- misc libnvdimm and DAX cleanups"
* tag 'libnvdimm-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/security: ensure sysfs poll thread woke up and fetch updated attr
libnvdimm/security: the 'security' attr never show 'overwrite' state
libnvdimm/security: fix a typo
ACPI: NFIT: Fix ARS zero-sized allocation
dax: Fix incorrect argument passed to xas_set_err()
ACPI: NFIT: Add runtime firmware activate support
PM, libnvdimm: Add runtime firmware activation support
libnvdimm: Convert to DEVICE_ATTR_ADMIN_RO()
drivers/dax: Expand lock scope to cover the use of addresses
fs/dax: Remove unused size parameter
dax: print error message by pr_info() in __generic_fsdax_supported()
driver-core: Introduce DEVICE_ATTR_ADMIN_{RO,RW}
tools/testing/nvdimm: Emulate firmware activation commands
tools/testing/nvdimm: Prepare nfit_ctl_test() for ND_CMD_CALL emulation
tools/testing/nvdimm: Add command debug messages
tools/testing/nvdimm: Cleanup dimm index passing
ACPI: NFIT: Define runtime firmware activation commands
ACPI: NFIT: Move bus_dsm_mask out of generic nvdimm_bus_descriptor
libnvdimm: Validate command family indices
|
|
Abstract platform specific mechanics for nvdimm firmware activation
behind a handful of generic ops. At the bus level ->activate_state()
indicates the unified state (idle, busy, armed) of all DIMMs on the bus,
and ->capability() indicates the system state expectations for activate.
At the DIMM level ->activate_state() indicates the per-DIMM state,
->activate_result() indicates the outcome of the last activation
attempt, and ->arm() attempts to transition the DIMM from 'idle' to
'armed'.
A new hibernate_quiet_exec() facility is added to support firmware
activation in an OS defined system quiesce state. It leverages the fact
that the hibernate-freeze state wants to assert that a memory
hibernation snapshot can be taken. This is in contrast to a platform
firmware defined quiesce state that may forcefully quiet the memory
controller independent of whether an individual device-driver properly
supports hibernate-freeze.
The libnvdimm sysfs interface is extended to support detection of a
firmware activate capability. The mechanism supports enumeration and
triggering of firmware activate, optionally in the
hibernate_quiet_exec() context.
[rafael: hibernate_quiet_exec() proposal]
[vishal: fix up sparse warning, grammar in Documentation/]
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Co-developed-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
In hibernate.c, some places lack of spaces while some places have
redundant spaces. So fix them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Hibernation concurrency handling is currently delegated to user.c,
where it's also used for regulating the access to the snapshot device.
In the prospective of making user.c a separate configuration option,
such mutual exclusion is brought into hibernate.c and made available
through accessor helpers hereby introduced.
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the kernel threads are not frozen in software_resume(), so
between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
system_freezable_power_efficient_wq can still try to submit SCSI
commands and this can cause a panic since the low level SCSI driver
(e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
any SCSI commands: https://lkml.org/lkml/2020/4/10/47
At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
to resolve the issue from hv_storvsc, but with the help of
Bart Van Assche, I realized it's better to fix software_resume(),
since this looks like a generic issue, not only pertaining to SCSI.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If hibernation_restore() fails, the 'error' should not be zero.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Hibernation fails when the kernel cannot allocate enough memory
to copy all pages of RAM in use.
Ensure that the failure reason is clearly logged, and clearly
attributable to the hibernation module.
Signed-off-by: Luigi Semenzato <semenzato@google.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is currently no way to verify the resume image when returning
from hibernate. This might compromise the signed modules trust model,
so until we can work with signed hibernate images we disable it when the
kernel is locked down.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: rjw@rjwysocki.net
Cc: pavel@ucw.cz
cc: linux-pm@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
|
|
* pm-x86:
x86/power: Fix 'nosmt' vs hibernation triple fault during resume
x86: intel_epb: Do not build when CONFIG_PM is unset
|
|
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As explained in
0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
we always, no matter what, have to bring up x86 HT siblings during boot at
least once in order to avoid first MCE bringing the system to its knees.
That means that whenever 'nosmt' is supplied on the kernel command-line,
all the HT siblings are as a result sitting in mwait or cpudile after
going through the online-offline cycle at least once.
This causes a serious issue though when a kernel, which saw 'nosmt' on its
commandline, is going to perform resume from hibernation: if the resume
from the hibernated image is successful, cr3 is flipped in order to point
to the address space of the kernel that is being resumed, which in turn
means that all the HT siblings are all of a sudden mwaiting on address
which is no longer valid.
That results in triple fault shortly after cr3 is switched, and machine
reboots.
Fix this by always waking up all the SMT siblings before initiating the
'restore from hibernation' process; this guarantees that all the HT
siblings will be properly carried over to the resumed kernel waiting in
resume_play_dead(), and acted upon accordingly afterwards, based on the
target kernel configuration.
Symmetricaly, the resumed kernel has to push the SMT siblings to mwait
again in case it has SMT disabled; this means it has to online all
the siblings when resuming (so that they come out of hlt) and offline
them again to let them reach mwait.
Cc: 4.19+ <stable@vger.kernel.org> # v4.19+
Debugged-by: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On systems with ACPI platform firmware the last stage of hibernation
is analogous to system suspend to S3 (suspend-to-RAM), so it should
be handled analogously. In particular, pm_suspend_via_firmware()
should return 'true' in that stage to let the callers of it know that
control will be passed to the platform firmware going forward, so
pm_set_suspend_via_firmware() needs to be called then in analogy with
acpi_suspend_begin().
However, the platform hibernation ->begin() callback is invoked
during the "freeze" transition (before creating a snapshot image of
system memory) as well as during the "hibernate" transition which is
the last stage of it and pm_set_suspend_via_firmware() should be
invoked by that callback in the latter stage only.
In order to implement that redefine the hibernation ->begin()
callback to take a pm_message_t argument to indicate which stage
of hibernation is taking place and rework acpi_hibernation_begin()
and acpi_hibernation_begin_old() to take it into account as needed.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These fix the (Intel-specific) Performance and Energy Bias Hint (EPB)
handling and expose it to user space via sysfs, fix and clean up
several cpufreq drivers, add support for two new chips to the qoriq
cpufreq driver, fix, simplify and clean up the cpufreq core and the
schedutil governor, add support for "CPU" domains to the generic power
domains (genpd) framework and provide low-level PSCI firmware support
for that feature, fix the exynos cpuidle driver and fix a couple of
issues in the devfreq subsystem and clean it up.
Specifics:
- Fix the handling of Performance and Energy Bias Hint (EPB) on Intel
processors and expose it to user space via sysfs to avoid having to
access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor and
rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to some PM
documentation files and unify copyright notices in them (Rafael
Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to the
rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan)"
* tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
cpufreq: Fix kobject memleak
cpufreq: armada-37xx: fix frequency calculation for opp
cpufreq: centrino: Fix centrino_setpolicy() kerneldoc comment
cpufreq: qoriq: add support for lx2160a
x86: tsc: Rework time_cpufreq_notifier()
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
cpufreq: qoriq: Add ls1028a chip support
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
cpufreq: Move ->get callback check outside of __cpufreq_get()
PM / Domains: remove unnecessary unlikely()
cpufreq: Remove needless bios_limit check in show_bios_limit()
drivers/cpufreq/acpi-cpufreq.c: This fixes the following checkpatch warning
firmware/psci: add support for SYSTEM_RESET2
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
...
|
|
This adds a function to disable secondary CPUs for suspend that are
not necessarily non-zero / non-boot CPUs. Platforms will be able to
use this to suspend using non-zero CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20190411033448.20842-3-npiggin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Create a common helper to sync filesystems for system suspend and
hibernation.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
At present, "systemctl suspend" and "shutdown" can run in parrallel. A
system can suspend after devices_shutdown(), and resume. Then the shutdown
task goes on to power off. This causes many devices are not really shut
off. Hence replacing reboot_mutex with system_transition_mutex (renamed
from pm_mutex) to achieve the exclusion. The renaming of pm_mutex as
system_transition_mutex can be better to reflect the purpose of the mutex.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This addresses Coverity-ID: 114713 ("Missing break in switch").
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
timekeeping suspend/resume calls read_persistent_clock() which takes
rtc_lock. That results in might sleep warnings because at that point
we run with interrupts disabled.
We cannot convert rtc_lock to a raw spinlock as that would trigger
other might sleep warnings.
As a workaround we disable the might sleep warnings by setting
system_state to SYSTEM_SUSPEND before calling sysdev_suspend() and
restoring it to SYSTEM_RUNNING afer sysdev_resume(). There is no lock
contention because hibernate / suspend to RAM is single-CPU at this
point.
In s2idle's case the system_state is set to SYSTEM_SUSPEND before
timekeeping_suspend() which is invoked by the last CPU. In the resume
case it set back to SYSTEM_RUNNING after timekeeping_resume() which is
invoked by the first CPU in the resume case. The other CPUs will block
on tick_freeze_lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: cover s2idle in tick_freeze() / tick_unfreeze()]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
|
|
Using this helper allows us to avoid the in-kernel calls to the
sys_sync() syscall. The ksys_ prefix denotes that this function
is meant as a drop-in replacement for the syscall. In particular, it
uses the same calling convention as sys_sync().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
This file is used both for setting the wakeup device without kernel
command line as well as for actually waking the system (when appropriate
swap header is in place).
To avoid confusion on incorrect logs in system log downgrade the
message to debug and make it clearer.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the only way to specify a hibernate offset for a
swap file is on the kernel command line.
Add a new /sys/power/resume_offset that lets userspace
specify the offset and disk to use when initiating a hibernate
cycle.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Regardless of whether or not debug messages from the core system
suspend/hibernation code are enabled, it is useful to know when
system-wide transitions start and finish (or fail), so print "info"
messages at these points.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Salyzyn <salyzyn@android.com>
|
|
Debug messages from the system suspend/hibernation infrastructure can
fill up the entire kernel log buffer in some cases and anyway they
are only useful for debugging. They depend on CONFIG_PM_DEBUG, but
that is set as a rule as some generally useful diagnostic facilities
depend on it too.
For this reason, avoid printing those messages by default, but make
it possible to turn them on as needed with the help of a new sysfs
attribute under /sys/power/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6332 488 308 7128 1bd8 kernel/power/hibernate.o
File size After adding 'const':
text data bss dec hex filename
6396 424 308 7128 1bd8 kernel/power/hibernate.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates deom Rafael Wysocki:
"These fix two bugs introduced by recent power management updates (in
the cpuidle menu governor and intel_pstate) and a few other issues,
clean up things and remove unused code.
Specifics:
- Fix for a cpuidle menu governor problem that started to take an
unnecessary spinlock after one of the recent updates and that did
not play well with the RT patch (Rafael Wysocki).
- Fix for the new intel_pstate operation mode switching feature added
recently that did not reinitialize P-state limits properly when
switching operation modes (Rafael Wysocki).
- Removal of unused global notifiers from the PM QoS framework
(Viresh Kumar).
- Generic power domains framework update to make it handle
asynchronous invocations of PM callbacks in the "noirq" phases of
system suspend/hibernation correctly (Ulf Hansson).
- Two hibernation core cleanups (Rafael Wysocki).
- intel_idle cleanup related to the sysfs interface (Len Brown).
- Off-by-one bug fix in the OPP (Operating Performance Points)
framework (Andrzej Hajda).
- OPP framework's documentation fix (Viresh Kumar).
- cpufreq qoriq driver cleanup (Tang Yuantian).
- Fixes for typos in comments in the device runtime PM framework
(Christophe Jaillet)"
* tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Documentation: Fix opp-microvolt in examples
intel_idle: stop exposing platform acronyms in sysfs
cpufreq: intel_pstate: Fix limits issue with operation mode switching
PM / hibernate: Define pr_fmt() and use pr_*() instead of printk()
PM / hibernate: Untangle power_down()
cpuidle: menu: Avoid taking spinlock for accessing QoS values
PM / QoS: Remove global notifiers
PM / runtime: Fix some typos
cpufreq: qoriq: clean up unused code
PM / OPP: fix off-by-one bug in dev_pm_opp_get_max_volt_latency loop
PM / Domains: Power off masters immediately in the power off sequence
PM / Domains: Rename is_async to one_dev_on for genpd_power_off()
PM / Domains: Move genpd_power_off() above genpd_power_on()
|
|
<linux/sched/nmi.h>
We are going to move softlockup APIs out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
<linux/nmi.h> already includes <linux/sched.h>.
Include the <linux/nmi.h> header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Define a pr_fmt() for hibernate.c and convert all of the explicit
printk() calls into corresponding pr_*() so that they use the
pr_fmt() format.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The power_down() routine in the core hibernation code is not exactly
straightforward (to put it lightly), so clean it up to make it avoid
invoking itself recursively, among other things.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Both of these options are poorly named. The features they provide are
necessary for system security and should not be considered debug only.
Change the names to CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX to better describe what these options do.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
PAGE_POISONING_ZERO disables zeroing new pages on alloc, they are
poisoned (zeroed) as they become available.
In the hibernate use case, free pages will appear in the system without
being cleared, left there by the loading kernel.
This patch will make sure free pages are cleared on resume when
PAGE_POISONING_ZERO is enabled. We free the pages just after resume
because we can't do it later: going through any device resume code might
allocate some memory and invalidate the free pages bitmap.
Thus we don't need to disable hibernation when PAGE_POISONING_ZERO is
enabled.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-sleep:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
* pm-cpufreq:
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume)
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Reported-by: Jiri Kosina <jikos@kernel.org>
Tested-by: Rafael J. Wysocki <rafael@kernel.org>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, the majority of changes go into the cpufreq subsystem, but
there are no big features this time. The cpufreq changes that stand
out somewhat are the governor interface rework and improvements
related to the handling of frequency tables. Apart from those, there
are fixes and new device/CPU IDs in drivers, cleanups and an
improvement of the new schedutil governor.
Next, there are some changes in the hibernation core, including a fix
for a nasty problem related to the MONITOR/MWAIT usage by CPU offline
during resume from hibernation, a few core improvements related to
memory management during resume, a couple of additional debug features
and cleanups.
Finally, we have some fixes and cleanups in the devfreq subsystem,
generic power domains framework improvements related to system
suspend/resume, support for some new chips in intel_idle and in the
power capping RAPL driver, a new version of the AnalyzeSuspend utility
and some assorted fixes and cleanups.
Specifics:
- Rework the cpufreq governor interface to make it more
straightforward and modify the conservative governor to avoid using
transition notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if the
frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan, Jan
Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing of
MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and a
page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related to
hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to version
4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle system
suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu,
exynos-bus) and in the core, make some devfreq code explicitly
non-modular and change some of it into tristate (Bartlomiej
Zolnierkiewicz, Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make it
export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat (Andy
Shevchenko)"
* tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
Revert "cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency"
PM / hibernate: Introduce test_resume mode for hibernation
cpufreq: export cpufreq_driver_resolve_freq()
cpufreq: Disallow ->resolve_freq() for drivers providing ->target_index()
PCI / PM: check all fields in pci_set_platform_pm()
cpufreq: acpi-cpufreq: use cached frequency mapping when possible
cpufreq: schedutil: map raw required frequency to driver frequency
cpufreq: add cpufreq_driver_resolve_freq()
cpufreq: intel_pstate: Check cpuid for MSR_HWP_INTERRUPT
intel_pstate: Update cpu_frequency tracepoint every time
cpufreq: intel_pstate: clean remnant struct element
PM / tools: scripts: AnalyzeSuspend v4.2
x86 / hibernate: Use hlt_play_dead() when resuming from hibernation
cpufreq: powernv: Replacing pstate_id with frequency table index
intel_pstate: Fix MSR_CONFIG_TDP_x addressing in core_get_max_pstate()
PM / hibernate: Image data protection during restoration
PM / hibernate: Add missing braces in __register_nosave_region()
PM / hibernate: Clean up comments in snapshot.c
PM / hibernate: Clean up function headers in snapshot.c
PM / hibernate: Add missing braces in hibernate_setup()
...
|
|
test_resume mode is to verify if the snapshot data
written to swap device can be successfully restored
to memory. It is useful to ease the debugging process
on hibernation, since this mode can not only bypass
the BIOSes/bootloader, but also the system re-initialization.
To avoid the risk to break the filesystm on persistent storage,
this patch resumes the image with tasks frozen.
For example:
echo test_resume > /sys/power/disk
echo disk > /sys/power/state
[ 187.306470] PM: Image saving progress: 70%
[ 187.395298] PM: Image saving progress: 80%
[ 187.476697] PM: Image saving progress: 90%
[ 187.554641] PM: Image saving done.
[ 187.558896] PM: Wrote 594600 kbytes in 0.90 seconds (660.66 MB/s)
[ 187.566000] PM: S|
[ 187.589742] PM: Basic memory bitmaps freed
[ 187.594694] PM: Checking hibernation image
[ 187.599865] PM: Image signature found, resuming
[ 187.605209] PM: Loading hibernation image.
[ 187.665753] PM: Basic memory bitmaps created
[ 187.691397] PM: Using 3 thread(s) for decompression.
[ 187.691397] PM: Loading and decompressing image data (148650 pages)...
[ 187.889719] PM: Image loading progress: 0%
[ 188.100452] PM: Image loading progress: 10%
[ 188.244781] PM: Image loading progress: 20%
[ 189.057305] PM: Image loading done.
[ 189.068793] PM: Image successfully loaded
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On Intel hardware, native_play_dead() uses mwait_play_dead() by
default and only falls back to the other methods if that fails.
That also happens during resume from hibernation, when the restore
(boot) kernel runs disable_nonboot_cpus() to take all of the CPUs
except for the boot one offline.
However, that is problematic, because the address passed to
__monitor() in mwait_play_dead() is likely to be written to in the
last phase of hibernate image restoration and that causes the "dead"
CPU to start executing instructions again. Unfortunately, the page
containing the address in that CPU's instruction pointer may not be
valid any more at that point.
First, that page may have been overwritten with image kernel memory
contents already, so the instructions the CPU attempts to execute may
simply be invalid. Second, the page tables previously used by that
CPU may have been overwritten by image kernel memory contents, so the
address in its instruction pointer is impossible to resolve then.
A report from Varun Koyyalagunta and investigation carried out by
Chen Yu show that the latter sometimes happens in practice.
To prevent it from happening, temporarily change the smp_ops.play_dead
pointer during resume from hibernation so that it points to a special
"play dead" routine which uses hlt_play_dead() and avoids the
inadvertent "revivals" of "dead" CPUs this way.
A slightly unpleasant consequence of this change is that if the
system is hibernated with one or more CPUs offline, it will generally
draw more power after resume than it did before hibernation, because
the physical state entered by CPUs via hlt_play_dead() is higher-power
than the mwait_play_dead() one in the majority of cases. It is
possible to work around this, but it is unclear how much of a problem
that's going to be in practice, so the workaround will be implemented
later if it turns out to be necessary.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106371
Reported-by: Varun Koyyalagunta <cpudebug@centtech.com>
Original-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
|
|
Make it possible to protect all pages holding image data during
hibernate image restoration by setting them read-only (so as to
catch attempts to write to those pages after image data have been
stored in them).
This adds overhead to image restoration code (it may cause large
page mappings to be split as a result of page flags changes) and
the errors it protects against should never happen in theory, so
the feature is only active after passing hibernate=protect_image
to the command line of the restore kernel.
Also it only is built if CONFIG_DEBUG_RODATA is set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make hibernate_setup() follow the coding style more closely by adding
some missing braces to the if () statement in it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This makes pm notifier PREPARE/POST symmetrical: if PREPARE
fails, we will only undo what ever happened on PREPARE.
It fixes the unbalanced CPU hotplug enable in CPU PM notifier.
Signed-off-by: Lianwei Wang <lianwei.wang@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With the following fix:
70595b479ce1 ("x86/power/64: Fix crash whan the hibernation code passes control to the image kernel")
... there is no longer a problem with hibernation resuming a
KASLR-booted kernel image, so remove the restriction.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux PM list <linux-pm@vger.kernel.org>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/20160613221002.GA29719@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
