| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"This patch set contains the main portion of the changes for 3.18 in
regard to the s390 architecture. It is a bit bigger than usual,
mainly because of a new driver and the vector extension patches.
The interesting bits are:
- Quite a bit of work on the tracing front. Uprobes is enabled and
the ftrace code is reworked to get some of the lost performance
back if CONFIG_FTRACE is enabled.
- To improve boot time with CONFIG_DEBIG_PAGEALLOC, support for the
IPTE range facility is added.
- The rwlock code is re-factored to improve writer fairness and to be
able to use the interlocked-access instructions.
- The kernel part for the support of the vector extension is added.
- The device driver to access the CD/DVD on the HMC is added, this
will hopefully come in handy to improve the installation process.
- Add support for control-unit initiated reconfiguration.
- The crypto device driver is enhanced to enable the additional AP
domains and to allow the new crypto hardware to be used.
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/ftrace: simplify enabling/disabling of ftrace_graph_caller
s390/ftrace: remove 31 bit ftrace support
s390/kdump: add support for vector extension
s390/disassembler: add vector instructions
s390: add support for vector extension
s390/zcrypt: Toleration of new crypto hardware
s390/idle: consolidate idle functions and definitions
s390/nohz: use a per-cpu flag for arch_needs_cpu
s390/vtime: do not reset idle data on CPU hotplug
s390/dasd: add support for control unit initiated reconfiguration
s390/dasd: fix infinite loop during format
s390/mm: make use of ipte range facility
s390/setup: correct 4-level kernel page table detection
s390/topology: call set_sched_topology early
s390/uprobes: architecture backend for uprobes
s390/uprobes: common library for kprobes and uprobes
s390/rwlock: use the interlocked-access facility 1 instructions
s390/rwlock: improve writer fairness
s390/rwlock: remove interrupt-enabling rwlock variant.
s390/mm: remove change bit override support
...
|
|
Move the nohz_delay bit from the s390_idle data structure to the
per-cpu flags. Clear the nohz delay flag in __cpu_disable and
remove the cpu hotplug notifier that used to do this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This way we unbloat a bit main.c and more importantly we initialize
nohz full after init_IRQ(). This dependency will be needed in further
patches because nohz full needs irq work to raise its own IRQ.
Information about the support for this ability on ARM64 is obtained on
init_IRQ() which initialize the pointer to __smp_call_function.
Since tick_init() is called right after init_IRQ(), this is a good place
to call tick_nohz_init() and prepare for that dependency.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
The local nohz kick is currently used by perf which needs it to be
NMI-safe. Recent commit though (7d1311b93e58ed55f3a31cc8f94c4b8fe988a2b9)
changed its implementation to fire the local kick using the remote kick
API. It was convenient to make the code more generic but the remote kick
isn't NMI-safe.
As a result:
WARNING: CPU: 3 PID: 18062 at kernel/irq_work.c:72 irq_work_queue_on+0x11e/0x140()
CPU: 3 PID: 18062 Comm: trinity-subchil Not tainted 3.16.0+ #34
0000000000000009 00000000903774d1 ffff880244e06c00 ffffffff9a7f1e37
0000000000000000 ffff880244e06c38 ffffffff9a0791dd ffff880244fce180
0000000000000003 ffff880244e06d58 ffff880244e06ef8 0000000000000000
Call Trace:
<NMI> [<ffffffff9a7f1e37>] dump_stack+0x4e/0x7a
[<ffffffff9a0791dd>] warn_slowpath_common+0x7d/0xa0
[<ffffffff9a07930a>] warn_slowpath_null+0x1a/0x20
[<ffffffff9a17ca1e>] irq_work_queue_on+0x11e/0x140
[<ffffffff9a10a2c7>] tick_nohz_full_kick_cpu+0x57/0x90
[<ffffffff9a186cd5>] __perf_event_overflow+0x275/0x350
[<ffffffff9a184f80>] ? perf_event_task_disable+0xa0/0xa0
[<ffffffff9a01a4cf>] ? x86_perf_event_set_period+0xbf/0x150
[<ffffffff9a187934>] perf_event_overflow+0x14/0x20
[<ffffffff9a020386>] intel_pmu_handle_irq+0x206/0x410
[<ffffffff9a0b54d3>] ? arch_vtime_task_switch+0x63/0x130
[<ffffffff9a01937b>] perf_event_nmi_handler+0x2b/0x50
[<ffffffff9a007b72>] nmi_handle+0xd2/0x390
[<ffffffff9a007aa5>] ? nmi_handle+0x5/0x390
[<ffffffff9a0d131b>] ? lock_release+0xab/0x330
[<ffffffff9a008062>] default_do_nmi+0x72/0x1c0
[<ffffffff9a0c925f>] ? cpuacct_account_field+0xcf/0x200
[<ffffffff9a008268>] do_nmi+0xb8/0x100
Lets fix this by restoring the use of local irq work for the nohz local
kick.
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Move the nohz kick code out of the scheduler tick to a dedicated IPI,
from Frederic Weisbecker.
This necessiated quite some background infrastructure rework,
including:
* Clean up some irq-work internals
* Implement remote irq-work
* Implement nohz kick on top of remote irq-work
* Move full dynticks timer enqueue notification to new kick
* Move multi-task notification to new kick
* Remove unecessary barriers on multi-task notification
- Remove proliferation of wait_on_bit() action functions and allow
wait_on_bit_action() functions to support a timeout. (Neil Brown)
- Another round of sched/numa improvements, cleanups and fixes. (Rik
van Riel)
- Implement fast idling of CPUs when the system is partially loaded,
for better scalability. (Tim Chen)
- Restructure and fix the CPU hotplug handling code that may leave
cfs_rq and rt_rq's throttled when tasks are migrated away from a dead
cpu. (Kirill Tkhai)
- Robustify the sched topology setup code. (Peterz Zijlstra)
- Improve sched_feat() handling wrt. static_keys (Jason Baron)
- Misc fixes.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
sched/fair: Fix 'make xmldocs' warning caused by missing description
sched: Use macro for magic number of -1 for setparam
sched: Robustify topology setup
sched: Fix sched_setparam() policy == -1 logic
sched: Allow wait_on_bit_action() functions to support a timeout
sched: Remove proliferation of wait_on_bit() action functions
sched/numa: Revert "Use effective_load() to balance NUMA loads"
sched: Fix static_key race with sched_feat()
sched: Remove extra static_key*() function indirection
sched/rt: Fix replenish_dl_entity() comments to match the current upstream code
sched: Transform resched_task() into resched_curr()
sched/deadline: Kill task_struct->pi_top_task
sched: Rework check_for_tasks()
sched/rt: Enqueue just unthrottled rt_rq back on the stack in __disable_runtime()
sched/fair: Disable runtime_enabled on dying rq
sched/numa: Change scan period code to match intent
sched/numa: Rework best node setting in task_numa_migrate()
sched/numa: Examine a task move when examining a task swap
sched/numa: Simplify task_numa_compare()
sched/numa: Use effective_load() to balance NUMA loads
...
|
|
Binding the grace-period kthreads to the timekeeping CPU resulted in
significant performance decreases for some workloads. For more detail,
see:
https://lkml.org/lkml/2014/6/3/395 for benchmark numbers
https://lkml.org/lkml/2014/6/4/218 for CPU statistics
It turns out that it is necessary to bind the grace-period kthreads
to the timekeeping CPU only when all but CPU 0 is a nohz_full CPU
on the one hand or if CONFIG_NO_HZ_FULL_SYSIDLE=y on the other.
In other cases, it suffices to bind the grace-period kthreads to the
set of non-nohz_full CPUs.
This commit therefore creates a tick_nohz_not_full_mask that is the
complement of tick_nohz_full_mask, and then binds the grace-period
kthread to the set of CPUs indicated by this new mask, which covers
the CONFIG_NO_HZ_FULL_SYSIDLE=n case. The CONFIG_NO_HZ_FULL_SYSIDLE=y
case still binds the grace-period kthreads to the timekeeping CPU.
This commit also includes the tick_nohz_full_enabled() check suggested
by Frederic Weisbecker.
Reported-by: Jet Chen <jet.chen@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Created housekeeping_affine() and housekeeping_mask per
fweisbec feedback. ]
|
|
Remotely kicking a full nohz CPU in order to make it re-evaluate its
next tick is currently implemented using the scheduler IPI.
However this bloats a scheduler fast path with an off-topic feature.
The scheduler tick was abused here for its cool "callable
anywhere/anytime" properties.
But now that the irq work subsystem can queue remote callbacks, it's
a perfect fit to safely queue IPIs when interrupts are disabled
without worrying about concurrent callers.
So lets implement remote kick on top of irq work. This is going to
be used when a new event requires the next tick to be recalculated:
more than 1 task competing on the CPU, timer armed, ...
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
This makes the code more symetric against the existing tick functions
called on irq exit: tick_irq_exit() and tick_nohz_irq_exit().
These function are also symetric as they mirror each other's action:
we start to account idle time on irq exit and we stop this accounting
on irq entry. Also the tick is stopped on irq exit and timekeeping
catches up with the tickless time elapsed until we reach irq entry.
This rename was suggested by Peter Zijlstra a long while ago but it
got forgotten in the mass.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1387320692-28460-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
Use a function with a meaningful name to check the global context
tracking state. static_key_false() is a bit confusing for reviewers.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
|
|
A few functions use remote per CPU access APIs when they
deal with local values.
Just do the right conversion to improve performance, code
readability and debug checks.
While at it, lets extend some of these function names with *_this_cpu()
suffix in order to display their purpose more clearly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/nohz
Pull nohz improvements from Frederic Weisbecker:
" It mostly contains fixes and full dynticks off-case optimizations. I believe that
distros want to enable this feature so it seems important to optimize the case
where the "nohz_full=" parameter is empty. ie: I'm trying to remove any performance
regression that comes with NO_HZ_FULL=y when the feature is not used.
This patchset improves the current situation a lot (off-case appears to be around 11% faster
with hackbench, although I guess it may vary depending on the configuration but it should be
significantly faster in any case) now there is still some work to do: I can still observe a
remaining loss of 1.6% throughput seen with hackbench compared to CONFIG_NO_HZ_FULL=n. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Scheduler IPIs and task context switches are serious fast path.
Let's try to hide as much as we can the impact of full
dynticks APIs' off case that are called on these sites
through the use of static keys.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
|
|
These APIs are frequenctly accessed and priority is given
to optimize the full dynticks off-case in order to let
distros enable this feature without suffering from
significant performance regressions.
Let's inline these APIs and optimize them with static keys.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
|
|
Revert commit 69a37bea (cpuidle: Quickly notice prediction failure for
repeat mode), because it has been identified as the source of a
significant performance regression in v3.8 and later as explained by
Jeremy Eder:
We believe we've identified a particular commit to the cpuidle code
that seems to be impacting performance of variety of workloads.
The simplest way to reproduce is using netperf TCP_RR test, so
we're using that, on a pair of Sandy Bridge based servers. We also
have data from a large database setup where performance is also
measurably/positively impacted, though that test data isn't easily
share-able.
Included below are test results from 3 test kernels:
kernel reverts
-----------------------------------------------------------
1) vanilla upstream (no reverts)
2) perfteam2 reverts e11538d1f03914eb92af5a1a378375c05ae8520c
3) test reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4
e11538d1f03914eb92af5a1a378375c05ae8520c
In summary, netperf TCP_RR numbers improve by approximately 4%
after reverting 69a37beabf1f0a6705c08e879bdd5d82ff6486c4. When
69a37beabf1f0a6705c08e879bdd5d82ff6486c4 is included, C0 residency
never seems to get above 40%. Taking that patch out gets C0 near
100% quite often, and performance increases.
The below data are histograms representing the %c0 residency @
1-second sample rates (using turbostat), while under netperf test.
- If you look at the first 4 histograms, you can see %c0 residency
almost entirely in the 30,40% bin.
- The last pair, which reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4,
shows %c0 in the 80,90,100% bins.
Below each kernel name are netperf TCP_RR trans/s numbers for the
particular kernel that can be disclosed publicly, comparing the 3
test kernels. We ran a 4th test with the vanilla kernel where
we've also set /dev/cpu_dma_latency=0 to show overall impact
boosting single-threaded TCP_RR performance over 11% above
baseline.
3.10-rc2 vanilla RX + c0 lock (/dev/cpu_dma_latency=0):
TCP_RR trans/s 54323.78
-----------------------------------------------------------
3.10-rc2 vanilla RX (no reverts)
TCP_RR trans/s 48192.47
Receiver %c0
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 0]:
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 59]:
***********************************************************
40.0000 - 50.0000 [ 1]: *
50.0000 - 60.0000 [ 0]:
60.0000 - 70.0000 [ 0]:
70.0000 - 80.0000 [ 0]:
80.0000 - 90.0000 [ 0]:
90.0000 - 100.0000 [ 0]:
Sender %c0
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 0]:
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 11]: ***********
40.0000 - 50.0000 [ 49]:
*************************************************
50.0000 - 60.0000 [ 0]:
60.0000 - 70.0000 [ 0]:
70.0000 - 80.0000 [ 0]:
80.0000 - 90.0000 [ 0]:
90.0000 - 100.0000 [ 0]:
-----------------------------------------------------------
3.10-rc2 perfteam2 RX (reverts commit
e11538d1f03914eb92af5a1a378375c05ae8520c)
TCP_RR trans/s 49698.69
Receiver %c0
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 1]: *
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 59]:
***********************************************************
40.0000 - 50.0000 [ 0]:
50.0000 - 60.0000 [ 0]:
60.0000 - 70.0000 [ 0]:
70.0000 - 80.0000 [ 0]:
80.0000 - 90.0000 [ 0]:
90.0000 - 100.0000 [ 0]:
Sender %c0
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 0]:
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 2]: **
40.0000 - 50.0000 [ 58]:
**********************************************************
50.0000 - 60.0000 [ 0]:
60.0000 - 70.0000 [ 0]:
70.0000 - 80.0000 [ 0]:
80.0000 - 90.0000 [ 0]:
90.0000 - 100.0000 [ 0]:
-----------------------------------------------------------
3.10-rc2 test RX (reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4
and e11538d1f03914eb92af5a1a378375c05ae8520c)
TCP_RR trans/s 47766.95
Receiver %c0
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 1]: *
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 27]: ***************************
40.0000 - 50.0000 [ 2]: **
50.0000 - 60.0000 [ 0]:
60.0000 - 70.0000 [ 2]: **
70.0000 - 80.0000 [ 0]:
80.0000 - 90.0000 [ 0]:
90.0000 - 100.0000 [ 28]: ****************************
Sender:
0.0000 - 10.0000 [ 1]: *
10.0000 - 20.0000 [ 0]:
20.0000 - 30.0000 [ 0]:
30.0000 - 40.0000 [ 11]: ***********
40.0000 - 50.0000 [ 0]:
50.0000 - 60.0000 [ 1]: *
60.0000 - 70.0000 [ 0]:
70.0000 - 80.0000 [ 3]: ***
80.0000 - 90.0000 [ 7]: *******
90.0000 - 100.0000 [ 38]: **************************************
These results demonstrate gaining back the tendency of the CPU to
stay in more responsive, performant C-states (and thus yield
measurably better performance), by reverting commit
69a37beabf1f0a6705c08e879bdd5d82ff6486c4.
Requested-by: Jeremy Eder <jeder@redhat.com>
Tested-by: Len Brown <len.brown@intel.com>
Cc: 3.8+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When a task is scheduled in, it may have some properties
of its own that could make the CPU reconsider the need for
the tick: posix cpu timers, perf events, ...
So notify the full dynticks subsystem when a task gets
scheduled in and re-check the tick dependency at this
stage. This is done through a self IPI to avoid messing
up with any current lock scenario.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
The scheduler IPI is used by the scheduler to kick
full dynticks CPUs asynchronously when more than one
task are running or when a new timer list timer is
enqueued. This way the destination CPU can decide
to restart the tick to handle this new situation.
Now let's call that kick in the scheduler IPI.
(Reusing the scheduler IPI rather than implementing
a new IPI was suggested by Peter Zijlstra a while ago)
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/nohz
Pull posix cpu timers handling on full dynticks from Frederic Weisbecker.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need full dynticks CPU to also be RCU nocb so
that we don't have to keep the tick to handle RCU
callbacks.
Make sure the range passed to nohz_full= boot
parameter is a subset of rcu_nocbs=
The CPUs that fail to meet this requirement will be
excluded from the nohz_full range. This is checked
early in boot time, before any CPU has the opportunity
to stop its tick.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Provide two new helpers in order to notify the full dynticks CPUs about
some internal system changes against which they may reconsider the state
of their tick. Some practical examples include: posix cpu timers, perf tick
and sched clock tick.
For now the notifying handler, implemented through IPIs, is a stub
that will be implemented when we get the tick stop/restart infrastructure
in.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
"Extended nohz" was used as a naming base for the full dynticks
API and Kconfig symbols. It reflects the fact the system tries
to stop the tick in more places than just idle.
But that "extended" name is a bit opaque and vague. Rename it to
"full" makes it clearer what the system tries to do under this
config: try to shutdown the tick anytime it can. The various
constraints that prevent that to happen shouldn't be considered
as fundamental properties of this feature but rather technical
issues that may be solved in the future.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
We are planning to convert the dynticks Kconfig options layout
into a choice menu. The user must be able to easily pick
any of the following implementations: constant periodic tick,
idle dynticks, full dynticks.
As this implies a mutual exclusion, the two dynticks implementions
need to converge on the selection of a common Kconfig option in order
to ease the sharing of a common infrastructure.
It would thus seem pretty natural to reuse CONFIG_NO_HZ to
that end. It already implements all the idle dynticks code
and the full dynticks depends on all that code for now.
So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and
CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ.
On the other hand we want to stay backward compatible: if
CONFIG_NO_HZ is set in an older config file, we want to
enable CONFIG_NO_HZ_IDLE by default.
But we can't afford both at the same time or we run into
a circular dependency:
1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select
CONFIG_NO_HZ
2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE
We might be able to support that from Kconfig/Kbuild but it
may not be wise to introduce such a confusing behaviour.
So to solve this, create a new CONFIG_NO_HZ_COMMON option
which gathers the common code between idle and full dynticks
(that common code for now is simply the idle dynticks code)
and select it from their referring Kconfig.
Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ
to it for backward compatibility.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
For extreme usecases such as Real Time or HPC, having
the ability to shutdown the tick when a single task runs
on a CPU is a desired feature:
* Reducing the amount of interrupts improves throughput
for CPU-bound tasks. The CPU is less distracted from its
real job, from an execution time and from the cache point
of views.
* This also improve latency response as we have less critical
sections.
Start with introducing a very simple interface to define
full dynticks CPU: use a boot time option defined cpumask
through the "nohz_extended=" kernel parameter. CPUs that
are part of this range will have their tick shutdown
whenever possible: provided they run a single task and
they don't do kernel activity that require the periodic
tick. These details will be later documented in
Documentation/*
An online CPU must be kept outside this range to handle the
timekeeping.
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Conflicts:
kernel/irq_work.c
Add support for printk in full dynticks CPU.
* Don't stop tick with irq works pending. This
fix is generally useful and concerns archs that
can't raise self IPIs.
* Flush irq works before CPU offlining.
* Introduce "lazy" irq works that can wait for the
next tick to be executed, unless it's stopped.
* Implement klogd wake up using irq work. This
removes the ad-hoc printk_tick()/printk_needs_cpu()
hooks and make it working even in dynticks mode.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
We need some quick way to check if the CPU has stopped
its tick. This will be useful to implement the printk tick
using the irq work subsystem.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The prediction for future is difficult and when the cpuidle governor prediction
fails and govenor possibly choose the shallower C-state than it should. How to
quickly notice and find the failure becomes important for power saving.
cpuidle menu governor has a method to predict the repeat pattern if there are 8
C-states residency which are continuous and the same or very close, so it will
predict the next C-states residency will keep same residency time.
There is a real case that turbostat utility (tools/power/x86/turbostat)
at kernel 3.3 or early. turbostat utility will read 10 registers one by one at
Sandybridge, so it will generate 10 IPIs to wake up idle CPUs. So cpuidle menu
governor will predict it is repeat mode and there is another IPI wake up idle
CPU soon, so it keeps idle CPU stay at C1 state even though CPU is totally
idle. However, in the turbostat, following 10 registers reading is sleep 5
seconds by default, so the idle CPU will keep at C1 for a long time though it is
idle until break event occurs.
In a idle Sandybridge system, run "./turbostat -v", we will notice that deep
C-state dangles between "70% ~ 99%". After patched the kernel, we will notice
deep C-state stays at >99.98%.
In the patch, a timer is added when menu governor detects a repeat mode and
choose a shallow C-state. The timer is set to a time out value that greater
than predicted time, and we conclude repeat mode prediction failure if timer is
triggered. When repeat mode happens as expected, the timer is not triggered
and CPU waken up from C-states and it will cancel the timer initiatively.
When repeat mode does not happen, the timer will be time out and menu governor
will quickly notice that the repeat mode prediction fails and then re-evaluates
deeper C-states possibility.
Below is another case which will clearly show the patch much benefit:
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
#include <signal.h>
#include <sys/time.h>
#include <time.h>
#include <pthread.h>
volatile int * shutdown;
volatile long * count;
int delay = 20;
int loop = 8;
void usage(void)
{
fprintf(stderr,
"Usage: idle_predict [options]\n"
" --help -h Print this help\n"
" --thread -n Thread number\n"
" --loop -l Loop times in shallow Cstate\n"
" --delay -t Sleep time (uS)in shallow Cstate\n");
}
void *simple_loop() {
int idle_num = 1;
while (!(*shutdown)) {
*count = *count + 1;
if (idle_num % loop)
usleep(delay);
else {
/* sleep 1 second */
usleep(1000000);
idle_num = 0;
}
idle_num++;
}
}
static void sighand(int sig)
{
*shutdown = 1;
}
int main(int argc, char *argv[])
{
sigset_t sigset;
int signum = SIGALRM;
int i, c, er = 0, thread_num = 8;
pthread_t pt[1024];
static char optstr[] = "n:l:t:h:";
while ((c = getopt(argc, argv, optstr)) != EOF)
switch (c) {
case 'n':
thread_num = atoi(optarg);
break;
case 'l':
loop = atoi(optarg);
break;
case 't':
delay = atoi(optarg);
break;
case 'h':
default:
usage();
exit(1);
}
printf("thread=%d,loop=%d,delay=%d\n",thread_num,loop,delay);
count = malloc(sizeof(long));
shutdown = malloc(sizeof(int));
*count = 0;
*shutdown = 0;
sigemptyset(&sigset);
sigaddset(&sigset, signum);
sigprocmask (SIG_BLOCK, &sigset, NULL);
signal(SIGINT, sighand);
signal(SIGTERM, sighand);
for(i = 0; i < thread_num ; i++)
pthread_create(&pt[i], NULL, simple_loop, NULL);
for (i = 0; i < thread_num; i++)
pthread_join(pt[i], NULL);
exit(0);
}
Get powertop V2 from git://github.com/fenrus75/powertop, build powertop.
After build the above test application, then run it.
Test plaform can be Intel Sandybridge or other recent platforms.
#./idle_predict -l 10 &
#./powertop
We will find that deep C-state will dangle between 40%~100% and much time spent
on C1 state. It is because menu governor wrongly predict that repeat mode
is kept, so it will choose the C1 shallow C-state even though it has chance to
sleep 1 second in deep C-state.
While after patched the kernel, we find that deep C-state will keep >99.6%.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that idle and nohz logics are going to be independant each others,
ts->idle_tick becomes too much a biased name to describe the field that
saves the last scheduled tick on top of which we re-calculate the next
tick to schedule when the timer is restarted.
We want to reuse this even to stop the tick outside idle cases. So let's
rename it to some more generic name: ts->last_tick.
This changes a bit the timer list stat export so we need to increase its
version.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
Earlier versions of RCU used the scheduling-clock tick to detect idleness
by checking for the idle task, but handled idleness differently for
CONFIG_NO_HZ=y. But there are now a number of uses of RCU read-side
critical sections in the idle task, for example, for tracing. A more
fine-grained detection of idleness is therefore required.
This commit presses the old dyntick-idle code into full-time service,
so that rcu_idle_enter(), previously known as rcu_enter_nohz(), is
always invoked at the beginning of an idle loop iteration. Similarly,
rcu_idle_exit(), previously known as rcu_exit_nohz(), is always invoked
at the end of an idle-loop iteration. This allows the idle task to
use RCU everywhere except between consecutive rcu_idle_enter() and
rcu_idle_exit() calls, in turn allowing architecture maintainers to
specify exactly where in the idle loop that RCU may be used.
Because some of the userspace upcall uses can result in what looks
to RCU like half of an interrupt, it is not possible to expect that
the irq_enter() and irq_exit() hooks will give exact counts. This
patch therefore expands the ->dynticks_nesting counter to 64 bits
and uses two separate bitfields to count process/idle transitions
and interrupt entry/exit transitions. It is presumed that userspace
upcalls do not happen in the idle loop or from usermode execution
(though usermode might do a system call that results in an upcall).
The counter is hard-reset on each process/idle transition, which
avoids the interrupt entry/exit error from accumulating. Overflow
is avoided by the 64-bitness of the ->dyntick_nesting counter.
This commit also adds warnings if a non-idle task asks RCU to enter
idle state (and these checks will need some adjustment before applying
Frederic's OS-jitter patches (http://lkml.org/lkml/2011/10/7/246).
In addition, validation of ->dynticks and ->dynticks_nesting is added.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
For the ondemand cpufreq governor, it is desired that the iowait
time is microaccounted in a similar way as idle time is.
This patch introduces the infrastructure to account and expose
this information via the get_cpu_iowait_time_us() function.
[akpm@linux-foundation.org: fix CONFIG_NO_HZ=n build]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082523.284feab6@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Now that the only user of ts->idle_lastupdate is
update_ts_time_stats(), the entire field can be eliminated.
In update_ts_time_stats(), idle_lastupdate is first set to
"now", and a few lines later, the only user is an if() statement
that assigns a variable either to "now" or to
ts->idle_lastupdate, which has the value of "now" at that point.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082439.2fab0b4f@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The previous patch which limits the sleep time to the maximum
deferment time of the time keeping clocksource has some limitations on
SMP machines: if all CPUs are idle then for all CPUs the maximum sleep
time is limited.
Solve this by keeping track of which cpu had the do_timer() duty
assigned last and limit the sleep time only for this cpu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
|
|
Allow the architecture to request a normal jiffy tick when the system
goes idle and tick_nohz_stop_sched_tick is called . On s390 the hook is
used to prevent the system going fully idle if there has been an
interrupt other than a clock comparator interrupt since the last wakeup.
On s390 the HiperSockets response time for 1 connection ping-pong goes
down from 42 to 34 microseconds. The CPU cost decreases by 27%.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20090929122533.402715150@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
commit 3f68535adad (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.
Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Reported-by: Luming Yu <luming.yu@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: Use new APIs
Convert kernel/time functions to use struct cpumask *.
Note the ugly bitmap declarations in tick-broadcast.c. These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in. This was safe.
(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
|
|
We have two separate nohz function calls in irq_enter() for no good
reason. Just call a single NOHZ function from irq_enter() and call
the bits in the tick code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
governor
export get_cpu_idle_time_us() for it to be used in ondemand governor.
Last update time can be current time when the CPU is currently non-idle,
accounting for the busy time since last idle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
On the tickless system(CONFIG_NO_HZ=y and CONFIG_HIGH_RES_TIMERS=n), after
I made an offlined cpu online, I found this cpu's event handler was
tick_handle_periodic, not tick_nohz_handler.
After debuging, I found this bug was caused by the wrong tick mode. the
tick mode is not changed to NOHZ_MODE_INACTIVE when the cpu is offline.
This patch fixes this bug.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
To allow better diagnosis of tick-sched related, especially NOHZ
related problems, we need to know when the last wakeup via an irq
happened and when the CPU left the idle state.
Add two fields (idle_waketime, idle_exittime) to the tick_sched
structure and add them to the timer_list output.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Current idle time in kstat is based on jiffies and is coarse grained.
tick_sched.idle_sleeptime is making some attempt to keep track of idle time
in a fine grained manner. But, it is not handling the time spent in
interrupts fully.
Make tick_sched.idle_sleeptime accurate with respect to time spent on
handling interrupts and also add tick_sched.idle_lastupdate, which keeps
track of last time when idle_sleeptime was updated.
This statistics will be crucial for cpufreq-ondemand governor, which can
shed some conservative gaurd band that is uses today while setting the
frequency. The ondemand changes that uses the exact idle time is coming
soon.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
commit e5a16b1f9eec0af7cfa0830304b41c1c0833cf9f
Author: Len Brown <len.brown@intel.com>
Date: Tue Oct 2 23:44:44 2007 -0400
cpuidle: shrink diff
processor_idle.c | 440 +++++++++++++++++++++++++++++++++++++++++--
1 file changed, 429 insertions(+), 11 deletions(-)
Signed-off-by: Len Brown <len.brown@intel.com>
commit dfbb9d5aedfb18848a3e0d6f6e3e4969febb209c
Author: Len Brown <len.brown@intel.com>
Date: Wed Sep 26 02:17:55 2007 -0400
cpuidle: reduce diff size
Reduces the cpuidle processor_idle.c diff vs 2.6.22 from this
processor_idle.c | 2006 ++++++++++++++++++++++++++-----------------
1 file changed, 1219 insertions(+), 787 deletions(-)
to this:
processor_idle.c | 502 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 458 insertions(+), 44 deletions(-)
...for the purpose of making the cpuilde patch less invasive
and easier to review.
no functional changes. build tested only.
Signed-off-by: Len Brown <len.brown@intel.com>
commit 889172fc915f5a7fe20f35b133cbd205ce69bf6c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:40:05 2007 -0700
cpuidle: Retain old ACPI policy for !CONFIG_CPU_IDLE
Retain the old policy in processor_idle, so that when CPU_IDLE is not
configured, old C-state policy will still be used. This provides a
clean gradual migration path from old ACPI policy to new cpuidle
based policy.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 9544a8181edc7ecc33b3bfd69271571f98ed08bc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:39:17 2007 -0700
cpuidle: Configure governors by default
Quoting Len "Do not give an option to users to shoot themselves in the foot".
Remove the configurability of ladder and menu governors as they are
needed for default policy of cpuidle. That way users will not be able to
have cpuidle without any policy loosing all C-state power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8975059a2c1e56cfe83d1bcf031bcf4cb39be743
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:27:07 2007 -0400
CPUIDLE: load ACPI properly when CPUIDLE is disabled
Change the registration return codes for when CPUIDLE
support is not compiled into the kernel. As a result, the ACPI
processor driver will load properly even if CPUIDLE is unavailable.
However, it may be possible to cleanup the ACPI processor driver further
and eliminate some dead code paths.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e0322e2b58dd1b12ec669bf84693efe0dc2414a8
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:26:06 2007 -0400
CPUIDLE: remove cpuidle_get_bm_activity()
Remove cpuidle_get_bm_activity() and updates governors
accordingly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 18a6e770d5c82ba26653e53d240caa617e09e9ab
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:58 2007 -0400
CPUIDLE: max_cstate fix
Currently max_cstate is limited to 0, resulting in no idle processor
power management on ACPI platforms. This patch restores the value to
the array size.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1fdc0887286179b40ce24bcdbde663172e205ef0
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:40 2007 -0400
CPUIDLE: handle BM detection inside the ACPI Processor driver
Update the ACPI processor driver to detect BM activity and
limit state entry depth internally, rather than exposing such
requirements to CPUIDLE. As a result, CPUIDLE can drop this
ACPI-specific interface and become more platform independent. BM
activity is now handled much more aggressively than it was in the
original implementation, so some testing coverage may be needed to
verify that this doesn't introduce any DMA buffer under-run issues.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ef38840db666f48e3cdd2b769da676c57228dd9
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:14 2007 -0400
CPUIDLE: menu governor updates
Tweak the menu governor to more effectively handle non-timer
break events. Non-timer break events are detected by comparing the
actual sleep time to the expected sleep time. In future revisions, it
may be more reliable to use the timer data structures directly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit bb4d74fca63fa96cf3ace644b15ae0f12b7df5a1
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:24:40 2007 -0400
CPUIDLE: fix 'current_governor' sysfs entry
Allow the "current_governor" sysfs entry to properly handle
input terminated with '\n'.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df3c71559bb69b125f1a48971bf0d17f78bbdf47
Author: Len Brown <len.brown@intel.com>
Date: Sun Aug 12 02:00:45 2007 -0400
cpuidle: fix IA64 build (again)
Signed-off-by: Len Brown <len.brown@intel.com>
commit a02064579e3f9530fd31baae16b1fc46b5a7bca8
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:27 2007 -0400
cpuidle: Remove support for runtime changing of max_cstate
Remove support for runtime changeability of max_cstate. Drivers can use
use latency APIs.
max_cstate can still be used as a boot time option and dmi override.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0912a44b13adf22f5e3f607d263aed23b4910d7e
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:16 2007 -0400
cpuidle: Remove ACPI cstate_limit calls from ipw2100
ipw2100 already has code to use accetable_latency interfaces to limit the
C-state. Remove the calls to acpi_set_cstate_limit and acpi_get_cstate_limit
as they are redundant.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c649a76e76be6bff1fd770d0a775798813a3f6e0
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:35:39 2007 -0400
cpuidle: compile fix for pause and resume functions
Fix the compilation failure when cpuidle is not compiled in.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Adam Belay <adam.belay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2305a5920fb8ee6ccec1c62ade05aa8351091d71
Author: Adam Belay <abelay@novell.com>
Date: Thu Jul 19 00:49:00 2007 -0400
cpuidle: re-write
Some portions have been rewritten to make the code cleaner and lighter
weight. The following is a list of changes:
1.) the state name is now included in the sysfs interface
2.) detection, hotplug, and available state modifications are handled by
CPUIDLE drivers directly
3.) the CPUIDLE idle handler is only ever installed when at least one
cpuidle_device is enabled and ready
4.) the menu governor BM code no longer overflows
5.) the sysfs attributes are now printed as unsigned integers, avoiding
negative values
6.) a variety of other small cleanups
Also, Idle drivers are no longer swappable during runtime through the
CPUIDLE sysfs inteface. On i386 and x86_64 most idle handlers (e.g.
poll, mwait, halt, etc.) don't benefit from an infrastructure that
supports multiple states, so I think using a more general case idle
handler selection mechanism would be cleaner.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df25b6b56955714e6e24b574d88d1fd11f0c3ee5
Author: Len Brown <len.brown@intel.com>
Date: Tue Jul 24 17:08:21 2007 -0400
cpuidle: fix IA64 buid
Signed-off-by: Len Brown <len.brown@intel.com>
commit fd6ada4c14488755ff7068860078c437431fbccd
Author: Adrian Bunk <bunk@stusta.de>
Date: Mon Jul 9 11:33:13 2007 -0700
cpuidle: static
make cpuidle_replace_governor() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c1d4a2cebcadf2429c0c72e1d29aa2a9684c32e0
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Jul 3 00:54:40 2007 -0400
cpuidle: static
This patch makes the needlessly global struct menu_governor static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit dbf8780c6e8d572c2c273da97ed1cca7608fd999
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:49:14 2007 -0400
export symbol tick_nohz_get_sleep_length
ERROR: "tick_nohz_get_sleep_length" [drivers/cpuidle/governors/menu.ko] undefined!
ERROR: "tick_nohz_get_idle_jiffies" [drivers/cpuidle/governors/menu.ko] undefined!
And please be sure to get your changes to core kernel suitably reviewed.
Cc: Adam Belay <abelay@novell.com>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 29f0e248e7017be15f99febf9143a2cef00b2961
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:43:04 2007 -0400
tick.h needs hrtimer.h
It uses hrtimers.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e40cede7d63a029e92712a3fe02faee60cc38fb4
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:40:34 2007 -0400
cpuidle: first round of documentation updates
Documentation changes based on Pavel's feedback.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 83b42be2efece386976507555c29e7773a0dfcd1
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:39:25 2007 -0400
cpuidle: add rating to the governors and pick the one with highest rating by default
Introduce a governor rating scheme to pick the right governor by default.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d2a74b8c5e8f22def4709330d4bfc4a29209b71c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:38:08 2007 -0400
cpuidle: make cpuidle sysfs driver governor switch off by default
Make default cpuidle sysfs to show current_governor and current_driver in
read-only mode. More elaborate available_governors and available_drivers with
writeable current_governor and current_driver interface only appear with
"cpuidle_sysfs_switch" boot parameter.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1f60a0e80bf83cf6b55c8845bbe5596ed8f6307b
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:37:00 2007 -0400
cpuidle: menu governor: change the early break condition
Change the C-state early break out algorithm in menu governor.
We only look at early breakouts that result in wakeups shorter than idle
state's target_residency. If such a breakout is frequent enough, eliminate
the particular idle state upto a timeout period.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 45a42095cf64b003b4a69be3ce7f434f97d7af51
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:35:38 2007 -0400
cpuidle: fix uninitialized variable in sysfs routine
Fix the uninitialized usage of ret.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 80dca7cdba3e6ee13eae277660873ab9584eb3be
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:34:16 2007 -0400
cpuidle: reenable /proc/acpi//power interface for the time being
Keep /proc/acpi/processor/CPU*/power around for a while as powertop depends
on it. It will be marked deprecated and removed in future. powertop can use
cpuidle interfaces instead.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 589c37c2646c5e3813a51255a5ee1159cb4c33fc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:32:37 2007 -0400
cpuidle: menu governor and hrtimer compile fix
Compile fix for menu governor.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ba80bd9ab3ed304cb4f19b722e4cc6740588b5e
Author: Len Brown <len.brown@intel.com>
Date: Thu May 31 22:51:43 2007 -0400
cpuidle: build fix - cpuidle vs ipw2100 module
ERROR: "acpi_set_cstate_limit" [drivers/net/wireless/ipw2100.ko] undefined!
Signed-off-by: Len Brown <len.brown@intel.com>
commit d7d8fa7f96a7f7682be7c6cc0cc53fa7a18c3b58
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:07 2007 -0400
cpuidle: add the 'menu' governor
Here is my first take at implementing an idle PM governor that takes
full advantage of NO_HZ. I call it the 'menu' governor because it
considers the full list of idle states before each entry.
I've kept the implementation fairly simple. It attempts to guess the
next residency time and then chooses a state that would meet at least
the break-even point between power savings and entry cost. To this end,
it selects the deepest idle state that satisfies the following
constraints:
1. If the idle time elapsed since bus master activity was detected
is below a threshold (currently 20 ms), then limit the selection
to C2-type or above.
2. Do not choose a state with a break-even residency that exceeds
the expected time remaining until the next timer interrupt.
3. Do not choose a state with a break-even residency that exceeds
the elapsed time between the last pair of break events,
excluding timer interrupts.
This governor has an advantage over "ladder" governor because it
proactively checks how much time remains until the next timer interrupt
using the tick infrastructure. Also, it handles device interrupt
activity more intelligently by not including timer interrupts in break
event calculations. Finally, it doesn't make policy decisions using the
number of state entries, which can have variable residency times (NO_HZ
makes these potentially very large), and instead only considers sleep
time deltas.
The menu governor can be selected during runtime using the cpuidle sysfs
interface like so:
"echo "menu" > /sys/devices/system/cpu/cpuidle/current_governor"
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit a4bec7e65aa3b7488b879d971651cc99a6c410fe
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:03 2007 -0400
cpuidle: export time until next timer interrupt using NO_HZ
Expose information about the time remaining until the next
timer interrupt expires by utilizing the dynticks infrastructure.
Also modify the main idle loop to allow dynticks to handle
non-interrupt break events (e.g. DMA). Finally, expose sleep ticks
information to external code. Thomas Gleixner is responsible for much
of the code in this patch. However, I've made some additional changes,
so I'm probably responsible if there are any bugs or oversights :)
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2929d8996fbc77f41a5ff86bb67cdde3ca7d2d72
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:46:58 2007 -0400
cpuidle: governor API changes
This patch prepares cpuidle for the menu governor. It adds an optional
stage after idle state entry to give the governor an opportunity to
check why the state was exited. Also it makes sure the idle loop
returns after each state entry, allowing the appropriate dynticks code
to run.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 3a7fd42f9825c3b03e364ca59baa751bb350775f
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Apr 26 00:03:59 2007 -0700
cpuidle: hang fix
Prevent hang on x86-64, when ACPI processor driver is added as a module on
a system that does not support C-states.
x86-64 expects all idle handlers to enable interrupts before returning from
idle handler. This is due to enter_idle(), exit_idle() races. Make
cpuidle_idle_call() confirm to this when there is no pm_idle_old.
Also, cpuidle look at the return values of attch_driver() and set
current_driver to NULL if attach fails on all CPUs.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4893339a142afbd5b7c01ffadfd53d14746e858e
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:09 2007 +0800
cpuidle: add support for max_cstate limit
With CPUIDLE framework, the max_cstate (to limit max cpu c-state)
parameter is ingored. Some systems require it to ignore C2/C3
and some drivers like ipw require it too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 43bbbbe1cb998cbd2df656f55bb3bfe30f30e7d1
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:13 2007 +0800
cpuidle: add cpuidle_fore_redetect_devices API
add cpuidle_force_redetect_devices API,
which forces all CPU redetect idle states.
Next patch will use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d1edadd608f24836def5ec483d2edccfb37b1d19
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:01 2007 +0800
cpuidle: fix sysfs related issue
Fix the cpuidle sysfs issue.
a. make kobject dynamicaly allocated
b. fixed sysfs init issue to avoid suspend/resume issue
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 7169a5cc0d67b263978859672e86c13c23a5570d
Author: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed Mar 28 22:52:53 2007 -0400
cpuidle: 1-bit field must be unsigned
A 1-bit bitfield has no room for a sign bit.
drivers/cpuidle/governors/ladder.c:54:16: error: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4658620158dc2fbd9e4bcb213c5b6fb5d05ba7d4
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 28 22:52:41 2007 -0400
cpuidle: fix boot hang
Patch for cpuidle boot hang reported by Larry Finger here.
http://www.ussg.iu.edu/hypermail/linux/kernel/0703.2/2025.html
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c17e168aa6e5fe3851baaae8df2fbc1cf11443a9
Author: Len Brown <len.brown@intel.com>
Date: Wed Mar 7 04:37:53 2007 -0500
cpuidle: ladder does not depend on ACPI
build fix for CONFIG_ACPI=n
In file included from drivers/cpuidle/governors/ladder.c:21:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:106: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:168: error: expected specifier-qualifier-list before âacpi_handleâ
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8c91d958246bde68db0c3f0c57b535962ce861cb
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Mar 6 02:29:40 2007 -0800
cpuidle: make code static
This patch makes the following needlessly global code static:
- driver.c: __cpuidle_find_driver()
- governor.c: __cpuidle_find_governor()
- ladder.c: struct ladder_governor
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0c39dc3187094c72c33ab65a64d2017b21f372d2
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 7 02:38:22 2007 -0500
cpu_idle: fix build break
This patch fixes a build breakage with !CONFIG_HOTPLUG_CPU and
CONFIG_CPU_IDLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8112e3b115659b07df340ef170515799c0105f82
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Mar 6 02:29:39 2007 -0800
cpuidle: build fix for !CPU_IDLE
Fix the compile issues when CPU_IDLE is not configured.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1eb4431e9599cd25e0d9872f3c2c8986821839dd
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:57 2007 -0800
cpuidle take2: Basic documentation for cpuidle
Documentation for cpuidle infrastructure
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit ef5f15a8b79123a047285ec2e3899108661df779
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:03 2007 -0800
cpuidle take2: Hookup ACPI C-states driver with cpuidle
Hookup ACPI C-states onto generic cpuidle infrastructure.
drivers/acpi/procesor_idle.c is now a ACPI C-states driver that registers as
a driver in cpuidle infrastructure and the policy part is removed from
drivers/acpi/processor_idle.c. We use governor in cpuidle instead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 987196fa82d4db52c407e8c9d5dec884ba602183
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:52:57 2007 -0800
cpuidle take2: Core cpuidle infrastructure
Announcing 'cpuidle', a new CPU power management infrastructure to manage
idle CPUs in a clean and efficient manner.
cpuidle separates out the drivers that can provide support for multiple types
of idle states and policy governors that decide on what idle state to use
at run time.
A cpuidle driver can support multiple idle states based on parameters like
varying power consumption, wakeup latency, etc (ACPI C-states for example).
A cpuidle governor can be usage model specific (laptop, server,
laptop on battery etc).
Main advantage of the infrastructure being, it allows independent development
of drivers and governors and allows for better CPU power management.
A huge thanks to Adam Belay and Shaohua Li who were part of this mini-project
since its beginning and are greatly responsible for this patchset.
This patch:
Core cpuidle infrastructure.
Introduces a new abstraction layer for cpuidle:
* which manages drivers that can support multiple idles states. Drivers
can be generic or particular to specific hardware/platform
* allows pluging in multiple policy governors that can take idle state policy
decision
* The core also has a set of sysfs interfaces with which administrato can know
about supported drivers and governors and switch them at run time.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
add /proc/timer_list, which prints all currently pending (high-res) timers,
all clock-event sources and their parameters in a human-readable form.
Sample output:
Timer List Version: v0.1
HRTIMER_MAX_CLOCK_BASES: 2
now at 4246046273872 nsecs
cpu: 0
clock 0:
.index: 0
.resolution: 1 nsecs
.get_time: ktime_get_real
.offset: 1273998312645738432 nsecs
active timers:
clock 1:
.index: 1
.resolution: 1 nsecs
.get_time: ktime_get
.offset: 0 nsecs
active timers:
#0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_stop_sched_tick, swapper/0
# expires at 4246432689566 nsecs [in 386415694 nsecs]
#1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, pcscd/2050
# expires at 4247018194689 nsecs [in 971920817 nsecs]
#2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, irqbalance/1909
# expires at 4247351358392 nsecs [in 1305084520 nsecs]
#3: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, crond/2157
# expires at 4249097614968 nsecs [in 3051341096 nsecs]
#4: <f5a90ec8>, it_real_fn, do_setitimer, syslogd/1888
# expires at 4251329900926 nsecs [in 5283627054 nsecs]
.expires_next : 4246432689566 nsecs
.hres_active : 1
.check_clocks : 0
.nr_events : 31306
.idle_tick : 4246020791890 nsecs
.tick_stopped : 1
.idle_jiffies : 986504
.idle_calls : 40700
.idle_sleeps : 36014
.idle_entrytime : 4246019418883 nsecs
.idle_sleeptime : 4178181972709 nsecs
cpu: 1
clock 0:
.index: 0
.resolution: 1 nsecs
.get_time: ktime_get_real
.offset: 1273998312645738432 nsecs
active timers:
clock 1:
.index: 1
.resolution: 1 nsecs
.get_time: ktime_get
.offset: 0 nsecs
active timers:
#0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_restart_sched_tick, swapper/0
# expires at 4246050084568 nsecs [in 3810696 nsecs]
#1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, atd/2227
# expires at 4261010635003 nsecs [in 14964361131 nsecs]
#2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, smartd/2332
# expires at 5469485798970 nsecs [in 1223439525098 nsecs]
.expires_next : 4246050084568 nsecs
.hres_active : 1
.check_clocks : 0
.nr_events : 24043
.idle_tick : 4246046084568 nsecs
.tick_stopped : 0
.idle_jiffies : 986510
.idle_calls : 26360
.idle_sleeps : 22551
.idle_entrytime : 4246043874339 nsecs
.idle_sleeptime : 4170763761184 nsecs
tick_broadcast_mask: 00000003
event_broadcast_mask: 00000001
CPU#0's local event device:
Clock Event Device: lapic
capabilities: 0000000e
max_delta_ns: 807385544
min_delta_ns: 1443
mult: 44624025
shift: 32
set_next_event: lapic_next_event
set_mode: lapic_timer_setup
event_handler: hrtimer_interrupt
.installed: 1
.expires: 4246432689566 nsecs
CPU#1's local event device:
Clock Event Device: lapic
capabilities: 0000000e
max_delta_ns: 807385544
min_delta_ns: 1443
mult: 44624025
shift: 32
set_next_event: lapic_next_event
set_mode: lapic_timer_setup
event_handler: hrtimer_interrupt
.installed: 1
.expires: 4246050084568 nsecs
Clock Event Device: hpet
capabilities: 00000007
max_delta_ns: 2147483647
min_delta_ns: 3352
mult: 61496110
shift: 32
set_next_event: hpet_next_event
set_mode: hpet_set_mode
event_handler: handle_nextevt_broadcast
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With Ingo Molnar <mingo@elte.hu>
Add functions to provide dynamic ticks and high resolution timers. The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks. The dyntick
functionality can be disabled on the kernel commandline. Provide also the
infrastructure to support high resolution timers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With Ingo Molnar <mingo@elte.hu>
The tick-management code is the first user of the clockevents layer. It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
