| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Honestly all the conflicts were simple overlapping changes,
nothing really interesting to report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_reset hook is not set anywhere. Drop it to make
stmmac_mdio_reset() smaller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only OF platforms use the reset delays and these delays are only read in
stmmac_mdio_reset(). Move them from struct stmmac_mdio_bus_data to a
stack variable inside stmmac_mdio_reset() because that's the only usage
of these delays.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No platform uses the "reset_gpio" field from stmmac_mdio_bus_data
anymore. Drop it so we don't get any new consumers either.
Plain GPIO numbers are being deprecated in favor of GPIO descriptors. If
needed any new non-OF platform can add a GPIO descriptor lookup table.
devm_gpiod_get_optional() will find the GPIO in that case.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because of PHYLINK conversion we stopped parsing the phy-handle property
from DT. Unfortunatelly, some wrapper drivers still rely on this phy
node to configure the PHY.
Let's restore the parsing of PHY handle while these wrapper drivers are
not fully converted to PHYLINK.
Fixes: 74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.
The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.706787045@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8a ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to the recent multi-queue changes the driver would configure the
queues to use the AVB mode, but the mode then got switched to DCB. The
hardware still works fine in DCB mode, but my testing capabilities are
limited, so it's safer to revert to the prior setting anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the configuration of RX queues' routing.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the configuration of RX and TX queues' priority.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:
a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right
b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of adding hooks inside stmmac_platform it is better to just use
the standard PM callbacks within the specific dwmac-driver. This only
used by the dwmac-rk driver.
This reverts commit cecbc5563a02 ("stmmac: allow to split suspend/resume
from init/exit callbacks").
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 88f8b1bb41c6208f81b6a480244533ded7b59493.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As dwmac-* drivers that need OF match have been converted
to use their own internal OF match data structure this can
now be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both of these fields are unused and has been unused since they
were added 3 and 5 years ago. Drop them since they are clearly
not very useful.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.
This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read the tx-fifo-depth and rx-fifo-depth from the devicetree. The Synopsys
stmmac controller fifos are configurable per product instance, and the fifo
sizes are needed to configure certain features correctly such as flow control.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These changes correct the following issues with jumbo frames on the
stmmac driver:
1) The Synopsys EMAC can be configured to support different FIFO
sizes at core configuration time. There's no way to query the
controller and know the FIFO size, so the driver needs to get this
information from the device tree in order to know how to correctly
handle MTU changes and setting up dma buffers. The default
max-frame-size is as currently used, which is the size of a jumbo
frame.
2) The driver was enabling Jumbo frames by default, but was not allocating
dma buffers of sufficient size to handle the maximum possible packet
size that could be received. This led to memory corruption since DMAs were
occurring beyond the extent of the allocated receive buffers for certain types
of network traffic.
kernel BUG at net/core/skbuff.c:126!
Internal error: Oops - BUG: 0 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 563 Comm: sockperf Not tainted 3.13.0-rc6-01523-gf7111b9 #31
task: ef35e580 ti: ef252000 task.ti: ef252000
PC is at skb_panic+0x60/0x64
LR is at skb_panic+0x60/0x64
pc : [<c03c7c3c>] lr : [<c03c7c3c>] psr: 60000113
sp : ef253c18 ip : 60000113 fp : 00000000
r10: ef3a5400 r9 : 00000ebc r8 : ef3a546c
r7 : ee59f000 r6 : ee59f084 r5 : ee59ff40 r4 : ee59f140
r3 : 000003e2 r2 : 00000007 r1 : c0b9c420 r0 : 0000007d
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2e8ac04a DAC: 00000015
Process sockperf (pid: 563, stack limit = 0xef252248)
Stack: (0xef253c18 to 0xef254000)
3c00: 00000ebc ee59f000
3c20: ee59f084 ee59ff40 ee59f140 c04a9cd8 ee8c50c0 00000ebc ee59ff40 00000000
3c40: ee59f140 c02d0ef0 00000056 ef1eda80 ee8c50c0 00000ebc 22bbef29 c0318f8c
3c60: 00000056 ef3a547c ffe2c716 c02c9c90 c0ba1298 ef3a5838 ef3a5838 ef3a5400
3c80: 000020c0 ee573840 000055cb ef3f2050 c053f0e0 c0319214 22b9b085 22d92813
3ca0: 00001c80 004b8e00 ef3a5400 ee573840 ef3f2064 22d92813 ef3f2064 000055cb
3cc0: ef3f2050 c031a19c ef252000 00000000 00000000 c0561bc0 00000000 ff00ffff
3ce0: c05621c0 ef3a5400 ef3f2064 ee573840 00000020 ef3f2064 000055cb ef3f2050
3d00: c053f0e0 c031cad0 c053e740 00000e60 00000000 00000000 ee573840 ef3a5400
3d20: ef0a6e00 00000000 ef3f2064 c032507c 00010000 00000020 c0561bc0 c0561bc0
3d40: ee599850 c032799c 00000000 ee573840 c055a380 ef3a5400 00000000 ef3f2064
3d60: ef3f2050 c032799c 0101c7c0 2b6755cb c059a280 c030e4d8 000055cb ffffffff
3d80: ee574fc0 c055a380 ee574000 ee573840 00002b67 ee573840 c03fe9c4 c053fa68
3da0: c055a380 00001f6f 00000000 ee573840 c053f0e0 c0304fdc ef0a6e01 ef3f2050
3dc0: ee573858 ef031000 ee573840 c03055d8 c0ba0c40 ef000f40 00100100 c053f0dc
3de0: c053ffdc c053f0f0 00000008 00000000 ef031000 c02da948 00001140 00000000
3e00: c0563c78 ef253e5f 00000020 ee573840 00000020 c053f0f0 ef313400 ee573840
3e20: c053f0e0 00000000 00000000 c05380c0 ef313400 00001000 00000015 c02df280
3e40: ee574000 ef001e00 00000000 00001080 00000042 005cd980 ef031500 ef031500
3e60: 00000000 c02df824 ef031500 c053e390 c0541084 f00b1e00 c05925e8 c02df864
3e80: 00001f5c ef031440 c053e390 c0278524 00000002 00000000 c0b9eb48 c02df280
3ea0: ee8c7180 00000100 c0542ca8 00000015 00000040 ef031500 ef031500 ef031500
3ec0: c027803c ef252000 00000040 000000ec c05380c0 c0b9eb40 c0b9eb48 c02df940
3ee0: ef060780 ffffa4dd c0564a9c c056343c 002e80a8 00000080 ef031500 00000001
3f00: c053808c ef252000 fffec100 00000003 00000004 002e80a8 0000000c c00258f0
3f20: 002e80a8 c005e704 00000005 00000100 c05634d0 c0538080 c05333e0 00000000
3f40: 0000000a c0565580 c05380c0 ffffa4dc c05434f4 00400100 00000004 c0534cd4
3f60: 00000098 00000000 fffec100 002e80a8 00000004 002e80a8 002a20e0 c0025da8
3f80: c0534cd4 c000f020 fffec10c c053ea60 ef253fb0 c0008530 0000ffe2 b6ef67f4
3fa0: 40000010 ffffffff 00000124 c0012f3c 0000ffe2 002e80f0 0000ffe2 00004000
3fc0: becb6338 becb6334 00000004 00000124 002e80a8 00000004 002e80a8 002a20e0
3fe0: becb6300 becb62f4 002773bb b6ef67f4 40000010 ffffffff 00000000 00000000
[<c03c7c3c>] (skb_panic+0x60/0x64) from [<c02d0ef0>] (skb_put+0x4c/0x50)
[<c02d0ef0>] (skb_put+0x4c/0x50) from [<c0318f8c>] (tcp_collapse+0x314/0x3ec)
[<c0318f8c>] (tcp_collapse+0x314/0x3ec) from [<c0319214>]
(tcp_try_rmem_schedule+0x1b0/0x3c4)
[<c0319214>] (tcp_try_rmem_schedule+0x1b0/0x3c4) from [<c031a19c>]
(tcp_data_queue+0x480/0xe6c)
[<c031a19c>] (tcp_data_queue+0x480/0xe6c) from [<c031cad0>]
(tcp_rcv_established+0x180/0x62c)
[<c031cad0>] (tcp_rcv_established+0x180/0x62c) from [<c032507c>]
(tcp_v4_do_rcv+0x13c/0x31c)
[<c032507c>] (tcp_v4_do_rcv+0x13c/0x31c) from [<c032799c>]
(tcp_v4_rcv+0x718/0x73c)
[<c032799c>] (tcp_v4_rcv+0x718/0x73c) from [<c0304fdc>]
(ip_local_deliver+0x98/0x274)
[<c0304fdc>] (ip_local_deliver+0x98/0x274) from [<c03055d8>]
(ip_rcv+0x420/0x758)
[<c03055d8>] (ip_rcv+0x420/0x758) from [<c02da948>]
(__netif_receive_skb_core+0x44c/0x5bc)
[<c02da948>] (__netif_receive_skb_core+0x44c/0x5bc) from [<c02df280>]
(netif_receive_skb+0x48/0xb4)
[<c02df280>] (netif_receive_skb+0x48/0xb4) from [<c02df824>]
(napi_gro_flush+0x70/0x94)
[<c02df824>] (napi_gro_flush+0x70/0x94) from [<c02df864>]
(napi_complete+0x1c/0x34)
[<c02df864>] (napi_complete+0x1c/0x34) from [<c0278524>]
(stmmac_poll+0x4e8/0x5c8)
[<c0278524>] (stmmac_poll+0x4e8/0x5c8) from [<c02df940>]
(net_rx_action+0xc4/0x1e4)
[<c02df940>] (net_rx_action+0xc4/0x1e4) from [<c00258f0>]
(__do_softirq+0x12c/0x2e8)
[<c00258f0>] (__do_softirq+0x12c/0x2e8) from [<c0025da8>] (irq_exit+0x78/0xac)
[<c0025da8>] (irq_exit+0x78/0xac) from [<c000f020>] (handle_IRQ+0x44/0x90)
[<c000f020>] (handle_IRQ+0x44/0x90) from [<c0008530>]
(gic_handle_irq+0x2c/0x5c)
[<c0008530>] (gic_handle_irq+0x2c/0x5c) from [<c0012f3c>]
(__irq_usr+0x3c/0x60)
3) The driver was setting the dma buffer size after allocating dma buffers,
which caused a system panic when changing the MTU.
BUG: Bad page state in process ifconfig pfn:2e850
page:c0b72a00 count:0 mapcount:0 mapping: (null) index:0x0
page flags: 0x200(arch_1)
Modules linked in:
CPU: 0 PID: 566 Comm: ifconfig Not tainted 3.13.0-rc6-01523-gf7111b9 #29
[<c001547c>] (unwind_backtrace+0x0/0xf8) from [<c00122dc>]
(show_stack+0x10/0x14)
[<c00122dc>] (show_stack+0x10/0x14) from [<c03c793c>] (dump_stack+0x70/0x88)
[<c03c793c>] (dump_stack+0x70/0x88) from [<c00b2620>] (bad_page+0xc8/0x118)
[<c00b2620>] (bad_page+0xc8/0x118) from [<c00b302c>]
(get_page_from_freelist+0x744/0x870)
[<c00b302c>] (get_page_from_freelist+0x744/0x870) from [<c00b40f4>]
(__alloc_pages_nodemask+0x118/0x86c)
[<c00b40f4>] (__alloc_pages_nodemask+0x118/0x86c) from [<c00b4858>]
(__get_free_pages+0x10/0x54)
[<c00b4858>] (__get_free_pages+0x10/0x54) from [<c00cba1c>]
(kmalloc_order_trace+0x24/0xa0)
[<c00cba1c>] (kmalloc_order_trace+0x24/0xa0) from [<c02d199c>]
(__kmalloc_reserve.isra.21+0x24/0x70)
[<c02d199c>] (__kmalloc_reserve.isra.21+0x24/0x70) from [<c02d240c>]
(__alloc_skb+0x68/0x13c)
[<c02d240c>] (__alloc_skb+0x68/0x13c) from [<c02d3930>]
(__netdev_alloc_skb+0x3c/0xe8)
[<c02d3930>] (__netdev_alloc_skb+0x3c/0xe8) from [<c0279378>]
(stmmac_open+0x63c/0x1024)
[<c0279378>] (stmmac_open+0x63c/0x1024) from [<c02e18cc>]
(__dev_open+0xa0/0xfc)
[<c02e18cc>] (__dev_open+0xa0/0xfc) from [<c02e1b40>]
(__dev_change_flags+0x94/0x158)
[<c02e1b40>] (__dev_change_flags+0x94/0x158) from [<c02e1c24>]
(dev_change_flags+0x18/0x48)
[<c02e1c24>] (dev_change_flags+0x18/0x48) from [<c0337bc0>]
(devinet_ioctl+0x638/0x700)
[<c0337bc0>] (devinet_ioctl+0x638/0x700) from [<c02c7aec>]
(sock_ioctl+0x64/0x290)
[<c02c7aec>] (sock_ioctl+0x64/0x290) from [<c0100890>]
(do_vfs_ioctl+0x78/0x5b8)
[<c0100890>] (do_vfs_ioctl+0x78/0x5b8) from [<c0100e0c>] (SyS_ioctl+0x3c/0x5c)
[<c0100e0c>] (SyS_ioctl+0x3c/0x5c) from [<c000e760>]
The fixes have been verified using reproducible, automated testing.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
force_thresh_dma_mode is set.
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
