| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
This is added to better utilize the HW resources (which now makes
one less packet data prefetch) and allow better scalability, on the
account of CPU usage (which now 'memcpy's the packet into the WQE).
To load balance between HW and CPU and get max packet rate, we use
watermarks to detect how much the HW is congested and move the work
loads back and forth between HW and CPU.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mlx5-next
Linux 5.1-rc1
We forgot to reset the branch last merge window thus mlx5-next is outdated
and still based on 5.0-rc2. This merge commit is needed to sync mlx5-next
branch with 5.1-rc1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create a new prio in the FDB, it will be used when inserting steering rules
into the FDB from the RDMA side. We create a new PRIO so rules from the
net side and rules from the RDMA side won't be inserted to the same PRIO,
each side has it's own sandbox to play in.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
When creating the FDB prios, use the enum values already defined and not
the hardcoded values.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mamameed says:
====================
mlx5-updates-2019-04-02
This series provides misc updates to mlx5 driver
1) Aya Levin (1): Handle event of power detection in the PCIE slot
2) Eli Britstein (6):
Some TC VLAN related updates and fixes to the previous VLAN modify action
support patchset.
Offload TC e-switch rules with egress/ingress VLAN devices
3) Max Gurtovoy (1): Fix double mutex initialization in esiwtch.c
4) Tariq Toukan (3): Misc small updates
A write memory barrier is sufficient in EQ ci update
Obsolete param field holding a constant value
Unify logic of MTU boundaries
5) Tonghao Zhang (4): Misc updates to en_tc.c
Make the log friendly when decapsulation offload not supported
Remove 'parse_attr' argument in parse_tc_fdb_actions()
Deletes unnecessary setting of esw_attr->parse_attr
Return -EOPNOTSUPP when attempting to offload an unsupported action
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle event of power state change in the PCIE slot. When the event
occurs, check if query power state and PCI power fields is supported. If
so, read these fields from MPEIN (management PCIE info) register and
issue a corresponding message.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Maxim, Remove un-used macros and spinlock from mlx5 code.
2) From Aya, Expose Management PCIE info register layout and add rate limit
print macros.
3) From Tariq, Compilation warning fix in fs_core.c
4) From Vu, Huy and Saeed, Improve mlx5 initialization flow:
The goal is to provide a better logical separation of mlx5 core
device initialization flow and will help to seamlessly support
creating different mlx5 device types such as PF, VF and SF
mlx5 sub-function virtual devices.
Mlx5_core driver needs to separate HCA resources from pci resources.
Its initialize/load/unload will be broken into stages:
1. Initialize common data structures
2. Setup function which initializes pci resources (for PF/VF)
or some other specific resources for virtual device
3. Initialize software objects according to hardware capabilities
4. Load all mlx5_core components
It is also necessary to detach mlx5_core mdev name/message from pci
device mdev->pdev name/message for a clearer report/debug of
different mlx5 device types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose PRM layout for handling MPEIN (Management PCIE Info). It will be
used in the downstream patch for querying MPEIN via the driver.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add bar_addr field to store bar-0 address to avoid calling
pci_resource_start with hard-coded bar-0 as parameter.
Also note that different mlx5 device types will have bar_addr
on different bars.
This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Software structure initialization should be in mdev_init stage.
This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.
This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As there is no user of mlx5_write64 that passes a spinlock to
mlx5_write64, remove this functionality and simplify the function.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5_*_DOORBELL_LOCK macros provided a way to avoid locking for
mlx5_write64 on 64-bit platforms where it's not necessary. Currently all
calls to mlx5_write64 don't use a spinlock, so the macros became unused.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Refresh tirs is looping over a global list of tirs while netdevs are
adding and removing tirs from that list. That is why a lock is
required.
Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
Add VLAN ID rewrite fields as a pre-step to support this rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To prevent a hardware memory leak when a DEVX DCT object is destroyed
without calling DRAIN DCT before, (e.g. under cleanup flow), need to
manage its creation and destruction via mlx5 core.
In that case the DRAIN DCT command will be called and only once that it
will be completed the DESTROY DCT command will be called. Otherwise, the
DESTROY DCT may fail and a hardware leak may occur.
As of that change the DRAIN DCT command should not be exposed any more
from DEVX, it's managed internally by the driver to work as expected by
the device specification.
Fixes: 7efce3691d33 ("IB/mlx5: Add obj create and destroy functionality")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Pull rdma updates from Jason Gunthorpe:
"This has been a slightly more active cycle than normal with ongoing
core changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5
On-Demand-Paging MR feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and
fixing the various unregistration race conditions in rxe's
unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
- drivers should not assume umem SGLs are in PAGE_SIZE chunks
- ucontext is accessed via udata not other means
- start to make the core code responsible for object memory
allocation
- drivers should convert struct device to struct ib_device via a
helper
- drivers have more tools to avoid use after unregister problems"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (280 commits)
net/mlx5: ODP support for XRC transport is not enabled by default in FW
IB/hfi1: Close race condition on user context disable and close
RDMA/umem: Revert broken 'off by one' fix
RDMA/umem: minor bug fix in error handling path
RDMA/hns: Use GFP_ATOMIC in hns_roce_v2_modify_qp
cxgb4: kfree mhp after the debug print
IB/rdmavt: Fix concurrency panics in QP post_send and modify to error
IB/rdmavt: Fix loopback send with invalidate ordering
IB/iser: Fix dma_nents type definition
IB/mlx5: Set correct write permissions for implicit ODP MR
bnxt_re: Clean cq for kernel consumers only
RDMA/uverbs: Don't do double free of allocated PD
RDMA: Handle ucontext allocations by IB/core
RDMA/core: Fix a WARN() message
bnxt_re: fix the regression due to changes in alloc_pbl
IB/mlx4: Increase the timeout for CM cache
IB/core: Abort page fault handler silently during owning process exit
IB/mlx5: Validate correct PD before prefetch MR
IB/mlx5: Protect against prefetch of invalid MR
RDMA/uverbs: Store PR pointer before it is overwritten
...
|
|
Under multipath offload scheme, as part of handling fib events, emit
mlx5 port affinity event on the enabled ports which will be handled by
the tc offloads code.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to offload ecmp-on-host scheme where next-hop routes are used,
we will make use of HW LAG. Add accessor function to let upper layers
in the driver to realize if the lag acts in multi-path mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff193 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
From
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
To resolve conflicts with net-next and pick up the first patch.
* branch 'mlx5-next':
net/mlx5: Factor out HCA capabilities functions
IB/mlx5: Add support for 50Gbps per lane link modes
net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register
net/mlx5: Add new fields to Port Type and Speed register
net/mlx5: Refactor queries to speed fields in Port Type and Speed register
net/mlx5: E-Switch, Avoid magic numbers when initializing offloads mode
net/mlx5: Relocate vport macros to the vport header file
net/mlx5: E-Switch, Normalize the name of uplink vport number
net/mlx5: Provide an alternative VF upper bound for ECPF
net/mlx5: Add host params change event
net/mlx5: Add query host params command
net/mlx5: Update enable HCA dependency
net/mlx5: Introduce Mellanox SmartNIC and modify page management logic
IB/mlx5: Use unified register/load function for uplink and VF vports
net/mlx5: Use consistent vport num argument type
net/mlx5: Use void pointer as the type in address_of macro
net/mlx5: Align ODP capability function with netdev coding style
mlx5: use RCU lock in mlx5_eq_cq_get()
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).
So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:
1. When registering, specify how many vports to register. This number
is the same for both drivers which is the total available vport
numbers.
2. When unregistering, specify the number of registered vports to do
unregister. Also, unload the repersentors which are already loaded.
It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.
Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:
create: (none) -> unregistered
reg: unregistered -> registered
load: registered -> loaded
unload: loaded -> registered
unreg: registered -> unregistered
Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.
With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).
Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Commands referring to vports use the following scheme:
1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
referred vport and put 1 in other_vport. It was assumed that driver
is accessing other vport when vport number is greater than 0.
With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.
As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When dealing with the offloads mode initialization, driver refers to
the number of VFs and add magic number one (1) to take account of the
uplink. This is not clear and will make the code less readable after
adding other vports (e.g. host PF). As these are special vports
compared to VF vports, add a helper macro to denote such special
vports and eliminate the use of magic number.
Moreover, when creating offloads flow table and groups, the driver
reserves two more slots for UC and MC miss rules. Replace this magic
number with a helper macro as well.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
These are two macros in the driver general header which deal with the
number of total vports and if a vport is vport manager. Such macros
are vport entities, better to place them at the vport header file.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Driver used to name uplink vport as FDB_UPLINK_VPORT, it's hard to
comply with the same naming convention along with the introduction of
other vports. Use MLX5_VPORT as the prefix for such vports and
relocate the uplink vport definition to public header file for the
benefits of both net and IB drivers.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
ECPF doesn't support SR-IOV, but an ECPF E-Switch manager shall know
the max VFs supported by its peer host PF in order to control those
VF vports.
The current driver implementation uses the total vfs quantity as
provided by the pci sub-system for an upper bound of the VF vports
the e-switch code needs to deal with. This obviously can't work as
is on ECPF e-switch manager. For now, we use a hard coded value of
128 on such systems.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.
The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.
To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.
With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.
When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.
The encoding before this patch was as follows:
function_id == 0: pages are requested for the function receiving
the EQE.
function_id != 0: pages are requested for VF identified by the
function_id value
A new one bit field in the EQE identifies that pages are requested for
the ECPF.
The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:
1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function
This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use u16 for vport number, which matches how hardware refers to this
argument throughout commands.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Better to use void * and avoid unnecessary casts.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
From
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
For dependencies needed in the next ODP patches.
* branch 'mlx5-next':
net/mlx5: Set ODP SRQ support in firmware
net/mlx5: Add XRC transport to ODP device capabilities layout
|
|
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
The device capabilities for ODP structure was missing the field for XRC
transport so add it here.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Yishai Hadas says:
Enable DEVX asynchronous query commands
This series enables querying a DEVX object in an asynchronous mode.
The userspace application won't block when calling the firmware and it will be
able to get the response back once that it will be ready.
To enable the above functionality:
- DEVX asynchronous command completion FD object was introduced.
- The applicable file operations were implemented to enable using it by
the user application.
- Query asynchronous method was added to the DEVX object, it will call the
firmware asynchronously and manages the response on the given input FD.
- Hot unplug support was added for the FD to work properly upon
unbind/disassociate.
- mlx5 core fence for asynchronous commands was implemented and used to
prevent racing upon unbind/disassociate.
This branch is based on mlx5-next & v5.0-rc2 due to dependencies, from
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
* branch 'devx-async':
IB/mlx5: Implement DEVX hot unplug for async command FD
IB/mlx5: Implement the file ops of DEVX async command FD
IB/mlx5: Introduce async DEVX obj query API
IB/mlx5: Introduce MLX5_IB_OBJECT_DEVX_ASYNC_CMD_FD
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
APIs that have deferred callbacks should have some kind of cleanup
function that callers can use to fence the callbacks. Otherwise things
like module unloading can lead to dangling function pointers, or worse.
The IB MR code is the only place that calls this function and had a
really poor attempt at creating this fence. Provide a good version in
the core code as future patches will add more places that need this
fence.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Manage indirection mkey upon DEVX flow to support ODP.
To support a page fault event on the indirection mkey it needs to be part
of the device mkey radix tree.
Both the creation and the deletion flows for a DEVX object which is
indirection mkey were adapted to handle that.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
