| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Leonard Crestez observed the following phenomenon: when using
hard interrupt triggers (the DRDY line coming out of an ST
sensor) sometimes a new value would arrive while reading the
previous value, due to latencies in the system.
We discovered that the ST hardware as far as can be observed
is designed for level interrupts: the DRDY line will be held
asserted as long as there are new values coming. The interrupt
handler should be re-entered until we're out of values to
handle from the sensor.
If interrupts were handled as occurring on the edges (usually
low-to-high) new values could appear and the line be held
asserted after that, and these values would be missed, the
interrupt handler would also lock up as new data was
available, but as no new edges occurs on the DRDY signal,
nothing happens: the edge detector only detects edges.
To counter this, do the following:
- Accept interrupt lines to be flagged as level interrupts
using IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW. If the line
is marked like this (in the device tree node or ACPI
table or similar) it will be utilized as a level IRQ.
We mark the line with IRQF_ONESHOT and mask the IRQ
while processing a sample, then the top half will be
entered again if new values are available.
- If we are flagged as using edge interrupts with
IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING: remove
IRQF_ONESHOT so that the interrupt line is not
masked while running the thread part of the interrupt.
This way we will never miss an interrupt, then introduce
a loop that polls the data ready registers repeatedly
until no new samples are available, then exit the
interrupt handler. This way we know no new values are
available when the interrupt handler exits and
new (edge) interrupts will be triggered when data arrives.
Take some extra care to update the timestamp in the poll
loop if this happens. The timestamp will not be 100%
perfect, but it will at least be closer to the actual
events. Usually the extra poll loop will handle the new
samples, but once in a blue moon, we get a new IRQ
while exiting the loop, before returning from the
thread IRQ bottom half with IRQ_HANDLED. On these rare
occasions, the removal of IRQF_ONESHOT means the
interrupt will immediately fire again.
- If no interrupt type is indicated from the DT/ACPI,
choose IRQF_TRIGGER_RISING as default, as this is necessary
for legacy boards.
Tested successfully on the LIS331DL and L3G4200D by setting
sampling frequency to 400Hz/800Hz and stressing the system:
extra reads in the threaded interrupt handler occurs.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Remove st_sensors_get_buffer_element symbol export since not explicitly
used outside of st_sensors driver.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is similar with support for creating triggers via configfs.
Devices will be hosted under:
* /config/iio/devices
We allow users to register "device types" under:
* /config/iio/devices/<device_types>/
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Expose a rotation matrix to indicate userspace the chip orientation with
respect to the overall hardware system.
Matrix is retrieved from "in_mount_matrix". It is declared into ak8975 DTS
entry as a "mount-matrix" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Expose a rotation matrix to indicate userspace the chip placement with
respect to the overall hardware system. This is needed to adjust
coordinates sampled from a sensor chip when its position deviates from the
main hardware system.
Final coordinates computation is delegated to userspace since:
* computation may involve floating point arithmetics ;
* it allows an application to combine adjustments with arbitrary
transformations.
This 3 dimentional space rotation matrix is expressed as 3x3 array of
strings to support floating point numbers. It may be retrieved from a
"[<dir>_][<type>_]mount_matrix" sysfs attribute file. It is declared into a
device / driver specific DTS property or platform data.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some of kernel driver uses the IIO framework to get the sensor
value via ADC or IIO HW driver. The client driver get iio channel
by iio_channel_get_all() and release it by calling
iio_channel_release_all().
Add resource managed version (devm_*) of these APIs so that if client
calls the devm_iio_channel_get_all() then it need not to release it
explicitly, it can be done by managed device framework when driver
get un-binded.
This reduces the code in error path and also need of .remove callback in
some cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some of kernel driver uses the IIO framework to get the sensor
value via ADC or IIO HW driver. The client driver get iio channel
by iio_channel_get() and release it by calling iio_channel_release().
Add resource managed version (devm_*) of these APIs so that if client
calls the devm_iio_channel_get() then it need not to release it explicitly,
it can be done by managed device framework when driver get un-binded.
This reduces the code in error path and also need of .remove callback in
some cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some variants of the devices from the ADIS family don't auto-clear the
self-test bit after the self-test has completed. Instead we have to
manually clear. Add support for this to the ADIS library.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The members buffer_group and attrs of iio_buffer_access_funcs have no
descriptions for the documentation. Adding them.
Fixes: 08e7e0adaa17 ("iio: buffer: Allocate standard attributes in the core")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
It is often the case that the driver wants to be sure a device stays
in direct mode while it is executing a task or series of tasks. To
accomplish this today, the driver performs this sequence: 1) take the
device state lock, 2) verify it is not in a buffered mode, 3) execute
some tasks, and 4) release that lock.
This patch introduces a pair of helper functions that simplify these
steps and make it more semantically expressive.
iio_device_claim_direct_mode()
If the device is not in any buffered mode it is guaranteed
to stay that way until iio_release_direct_mode() is called.
iio_device_release_direct_mode()
Release the claim. Device is no longer guaranteed to stay
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch fixes a few minor typos in the documentation comments for the
scan_type member of the iio_event_spec structure. The sign member name
was improperly capitalized as "Sign" in the comments. The storagebits
member name was improperly listed as "storage_bits" in the comments. The
endianness member entry in the comments was moved after the repeat
member entry in order to maintain consistency with the actual struct
iio_event_spec layout.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
mlock *must* be used by core and drivers to protect access
to devices state changes.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Make IIO value formating function globally available to allow IIO drivers
to output values as the core does.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
configfs_subsystem
This exported element needs to be accesible to all drivers using configfs
within IIO. Previously it was in the sw_trig.h file which only convered one
such usecase. This also fixes a sparse warning as it is now in a header
that makes sense to include from industrialio-configfs.c
Signed-off-by: Jonathan Cameron < jic23@kernel.org>
|
|
A software trigger associates an IIO device trigger with a software
interrupt source (e.g: timer, sysfs). This patch adds the generic
infrastructure for handling software triggers.
Software interrupts sources are kept in a iio_trigger_types_list and
registered separately when the associated kernel module is loaded.
Software triggers can be created directly from drivers or from user
space via configfs interface.
To sum up, this dynamically creates "triggers" group to be found under
/config/iio/triggers and offers the possibility of dynamically
creating trigger types groups. The first supported trigger type is
"hrtimer" found under /config/iio/triggers/hrtimer.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add a generic fully device independent DMA buffer implementation that uses
the DMAegnine framework to perform the DMA transfers. This can be used by
converter drivers that whish to provide a DMA buffer for converters that
are connected to a DMA core that implements the DMAengine API.
Apart from allocating the buffer using iio_dmaengine_buffer_alloc() and
freeing it using iio_dmaengine_buffer_free() no additional converter driver
specific code is required when using this DMA buffer implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The traditional approach used in IIO to implement buffered capture requires
the generation of at least one interrupt per sample. In the interrupt
handler the driver reads the sample from the device and copies it to a
software buffer. This approach has a rather large per sample overhead
associated with it. And while it works fine for samplerates in the range of
up to 1000 samples per second it starts to consume a rather large share of
the available CPU processing time once we go beyond that, this is
especially true on an embedded system with limited processing power. The
regular interrupt also causes increased power consumption by not allowing
the hardware into deeper sleep states, which is something that becomes more
and more important on mobile battery powered devices.
And while the recently added watermark support mitigates some of the issues
by allowing the device to generate interrupts at a rate lower than the data
output rate, this still requires a storage buffer inside the device and
even if it exists it is only a few 100 samples deep at most.
DMA support on the other hand allows to capture multiple millions or even
more samples without any CPU interaction. This allows the CPU to either go
to sleep for longer periods or focus on other tasks which increases overall
system performance and power consumption. In addition to that some devices
might not even offer a way to read the data other than using DMA, which
makes DMA mandatory to use for them.
The tasks involved in implementing a DMA buffer can be divided into two
categories. The first category is memory buffer management (allocation,
mapping, etc.) and hooking this up the IIO buffer callbacks like read(),
enable(), disable(), etc. The second category of tasks is to setup the
DMA hardware and manage the DMA transfers. Tasks from the first category
will be very similar for all IIO drivers supporting DMA buffers, while the
tasks from the second category will be hardware specific.
This patch implements a generic infrastructure that take care of the former
tasks. It provides a set of functions that implement the standard IIO
buffer iio_buffer_access_funcs callbacks. These can either be used as is or
be overloaded and augmented with driver specific code where necessary.
For the DMA buffer support infrastructure that is introduced in this series
sample data is grouped by so called blocks. A block is the basic unit at
which data is exchanged between the application and the hardware. The
application is responsible for allocating the memory associated with the
block and then passes the block to the hardware. When the hardware has
captured the amount of samples equal to size of a block it will notify the
application, which can then read the data from the block and process it.
The block size can freely chosen (within the constraints of the hardware).
This allows to make a trade-off between latency and management overhead.
The larger the block size the lower the per sample overhead but the latency
between when the data was captured and when the application will be able to
access it increases, in a similar way smaller block sizes have a larger per
sample management overhead but a lower latency. The ideal block size thus
depends on system and application requirements.
For the time being the infrastructure only implements a simple double
buffered scheme which allocates two blocks each with half the size of the
configured buffer size. This provides basic support for capturing
continuous uninterrupted data over the existing file-IO ABI. Future
extensions to the DMA buffer infrastructure will give applications a more
fine grained control over how many blocks are allocated and the size of
each block. But this requires userspace ABI additions which are
intentionally not part of this patch and will be added separately.
Tasks of the second category need to be implemented by a device specific
driver. They can be hooked up into the generic infrastructure using two
simple callbacks, submit() and abort().
The submit() callback is used to schedule DMA transfers for blocks. Once a
DMA transfer has been completed it is expected that the buffer driver calls
iio_dma_buffer_block_done() to notify. The abort() callback is used for
stopping all pending and active DMA transfers when the buffer is disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds a enable and disable callback that is called when the
buffer is enabled/disabled. This can be used by buffer implementations that
need to do some setup or teardown work. E.g. a DMA based buffer can use
this to start/stop the DMA transfer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
For buffers which have a fixed wake-up watermark the watermark attribute
should be read-only. Add a new FIXED_WATERMARK flag to the
struct iio_buffer_access_funcs, which can be set by a buffer
implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Support triggered events.
This is useful for chips that don't have their own interrupt sources.
It allows to use generic/standalone iio triggers for those drivers.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add inverse unit conversion macro to convert from standard IIO units to
units that might be used by some devices.
Those are useful in combination with scale factors that are specified as
IIO_VAL_FRACTIONAL. Typically the denominator for those specifications will
contain the maximum raw value the sensor will generate and the numerator
the value it maps to in a specific unit. Sometimes datasheets specify those
in different units than the standard IIO units (e.g. degree/s instead of
rad/s) and so we need to do a unit conversion.
From a mathematical point of view it does not make a difference whether we
apply the unit conversion to the numerator or the inverse unit conversion
to the denominator since (x / y) / z = x / (y * z). But as the denominator
is typically a larger value and we are rounding both the numerator and
denominator to integer values using the later method gives us a better
precision (E.g. the relative error is smaller if we round 8000.3 to 8000
rather than rounding 8.3 to 8).
This is where in inverse unit conversion macros will be used.
Marked for stable as used by some upcoming fixes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
When compile iio related driver the following warning shown:
include/linux/iio/trigger.h:35:34: warning: 'struct iio_trigger'
declared inside parameter list
int (*set_trigger_state)(struct iio_trigger *trig, bool state);
include/linux/iio/trigger.h:38:18: warning: 'struct iio_dev'
declared inside parameter list
struct iio_dev *indio_dev);
'struct iio_dev' and 'struct iio_trigger' was used before declaration,
forward declaration for these structs to fix warning.
Signed-off-by: Pengyu Ma <pengyu.ma@windriver.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fix kernel doc for the iio_dev_attr structure by adding its missing field.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fix buffer name from kernel doc according to the function parameter.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch renames the top half handler and the bottom half handler
of iio_triggered_buffer_setup() in accordance with their usage.
The bottom half has been renamed to reflect the fact that it is a
thread based call, compliant with iio_alloc_pollfunc().
The names of the parameters were swapped, thus creating confusion.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
For each buffer type specify the supported device modes for this buffer.
This allows us for devices which support multiple different operating modes
to pick the correct operating mode based on the modes supported by the
attached buffers.
It also prevents that buffers with conflicting modes are attached
to a device at the same time or that a buffer with a non-supported mode is
attached to a device (e.g. in-kernel callback buffer to a device only
supporting hardware mode).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add a high pass filter attribute for measurements
(like the existing low pass)
Also add both high and low pass attributes for events.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some magnetometers can perform a number of repetitions in HW
for each measurement to increase accuracy. One example is
Bosch BMC150:
http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf.
Introduce an interface to set the oversampling ratio
for these devices.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Contact-less IR temperature sensors measure the temperature of an object
by using its thermal radiation. Surfaces with different emissivity
ratios emit different amounts of energy at the same temperature.
IIO_CHAN_INFO_CALIBEMISSIVITY allows the user to inform the sensor of the
emissivity of the object in front of it, in order to effectively measure
its temperature.
A device providing such setting is Melexis's MLX90614:
http://melexis.com/Assets/IR-sensor-thermometer-MLX90614-Datasheet-5152.aspx.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some devices have hardware buffers that can store a number of samples
for later consumption. Hardware usually provides interrupts to notify
the processor when the FIFO is full or when it has reached a certain
watermark level. This helps with reducing the number of interrupts to
the host processor and thus it helps decreasing the power consumption.
This patch enables usage of hardware FIFOs for IIO devices in
conjunction with software device buffers. When the hardware FIFO is
enabled the samples are stored in the hardware FIFO. The samples are
later flushed to the device software buffer when the number of entries
in the hardware FIFO reaches the hardware watermark or when a flush
operation is triggered by the user when doing a non-blocking read
on an empty software device buffer.
In order to implement hardware FIFO support the device drivers must
implement the following new operations: setting and getting the
hardware FIFO watermark level, flushing the hardware FIFO to the
software device buffer. The device must also expose information about
the hardware FIFO such it's minimum and maximum watermark and if
necessary a list of supported watermark values. Finally, the device
driver must activate the hardware FIFO when the device buffer is
enabled, if the current device settings allows it.
The software device buffer watermark is passed by the IIO core to the
device driver as a hint for the hardware FIFO watermark. The device
driver can adjust this value to allow for hardware limitations (such
as capping it to the maximum hardware watermark or adjust it to a
value that is supported by the hardware). It can also disable the
hardware watermark (and implicitly the hardware FIFO) it this value is
below the minimum hardware watermark.
Since a driver may support hardware FIFO only when not in triggered
buffer mode (due to different semantics of hardware FIFO sampling and
triggered sampling) this patch changes the IIO core code to allow
falling back to non-triggered buffered mode if no trigger is enabled.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the IIO buffer blocking read only wait until at least one
data element is available.
This patch makes the reader sleep until enough data is collected before
returning to userspace. This should limit the read() calls count when
trying to get data in batches.
Co-author: Yannick Bedhomme <yannick.bedhomme@mobile-devices.fr>
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
[rebased and remove buffer timeout]
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MAX520 and MAX521 are protocol-compatible with the already supported
chips, just have more channels.
Signed-off-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
After UAPI header file split [1] all user-kernel interfaces were
placed under include/uapi/.
This patch moves IIO user specific API from:
* include/linux/iio/events.h => include/uapi/linux/iio/events.h
* include/linux/types.h => include/uapi/linux/types.h
Now there is no need for nasty tricks to compile userspace programs
(e.g iio_event_monitor). Just installing the kernel headers with
make headers_install command does the job.
[1] http://lwn.net/Articles/507794/
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The pedometer needs to filter out false steps that might be generated by
tapping the foot, sitting, etc. To do that it computes the number of
steps that occur in a given time and decides the user is moving only
if this value is over a threshold. E.g.: the user starts moving only
if he takes 4 steps in 3 seconds. This filter is applied only when
the user starts moving.
A device that has such pedometer functionality is Freescale's MMA9553L:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf.
To export this feature, this patch introduces IIO_CHAN_INFO_DEBOUNCE_COUNT
and IIO_CHAN_INFO_DEBOUNCE_TIME. For the pedometer, in_steps_debounce_count
will specify the number of steps that need to occur in
in_steps_debounce_time seconds so that the pedometer decides the user is
moving.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Sensorhub is MCU dedicated to collect data and manage several sensors.
Sensorhub is a spi device which provides a layer for IIO devices. It provides
some data parsing and common mechanism for sensorhub sensors.
Adds common sensorhub library for sensorhub driver and iio drivers
which uses sensorhub MCU to communicate with sensors.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
By introducing IIO_EV_TYPE_CHANGE, IIO_EV_TYPE_INSTANCE becomes redundant.
The effect of IIO_EV_TYPE_INSTANCE can be obtained by using IIO_EV_TYPE_CHANGE
with IIO_EV_INFO_VALUE set to 1.
Remove all instances of IIO_EV_TYPE_INSTANCE and replace them with
IIO_EV_TYPE_CHANGE where needed.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
A step detector will generate an interrupt each time N step are detected.
A device that has such pedometer functionality is Freescale's MMA9553L:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf.
Introduce IIO_EV_TYPE_CHANGE event type for events that are generated
when the channel passes a threshold on the absolute change in value.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some devices need the weight of the user to compute other
parameters. One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that needs the weight of the user to compute the number of calories burnt.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some devices export the current speed value of the user.
One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that computes the speed of the user based on the number of steps and
stride length.
Introduce a new channel type VELOCITY and a modifier for the magniture or
norm of the velocity vector, IIO_MOD_ROOT_SUM_SQUARED_X_Y_Z.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some devices export an estimation of the distance the user has covered
since the last reset.
One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that computes the distance based on the stride length and step rate.
Introduce a new channel type DISTANCE to export these values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Human activity sensors report the energy burnt by the user.
One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that computes the number of calories based on weight and step rate.
Introduce a new channel type ENERGY to export these values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
