| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce a driver for devices running Dasharo firmware. The driver
supports thermal monitoring using a new ACPI interface in Dasharo. The
initial version supports monitoring fan speeds, fan PWM duty cycles and
system temperatures as well as determining which specific interfaces are
implemented by firmware.
It has been tested on a NovaCustom laptop running pre-release Dasharo
firmware, which implements fan and thermal monitoring for the CPU and
the discrete GPU, if present.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Link: https://lore.kernel.org/all/20250507075214.36729-1-lukas.bulwahn@redhat.com
Link: https://lore.kernel.org/r/20250425112147.69308-2-michal.kopec@3mdeb.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Some of the external muxes needs powering up using a regulator.
This is the case with Lenovo T14s laptop which has a external audio mux
to handle US/EURO headsets.
Add support to the driver to handle this optional regulator.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250327100633.11530-3-srinivas.kandagatla@linaro.org
[krzk: Adjust dev_err message per Johan's review]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
SDEI usually initialize with the ACPI table, but on platforms where
ACPI is not used, the SDEI feature can still be used to handle
specific firmware calls or other customized purposes. Therefore, it
is not necessary for ARM_SDE_INTERFACE to depend on ACPI_APEI_GHES.
In commit dc4e8c07e9e2 ("ACPI: APEI: explicit init of HEST and GHES
in acpi_init()"), to make APEI ready earlier, sdei_init was moved
into acpi_ghes_init instead of being a standalone initcall, adding
ACPI_APEI_GHES dependency to ARM_SDE_INTERFACE. This restricts the
flexibility and usability of SDEI.
This patch corrects the dependency in Kconfig and splits sdei_init()
into two separate functions: sdei_init() and acpi_sdei_init().
sdei_init() will be called by arch_initcall and will only initialize
the platform driver, while acpi_sdei_init() will initialize the
device from acpi_ghes_init() when ACPI is ready. This allows the
initialization of SDEI without ACPI_APEI_GHES enabled.
Fixes: dc4e8c07e9e2 ("ACPI: APEI: explicit init of HEST and GHES in apci_init()")
Cc: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Reviewed-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250507045757.2658795-1-quic_hyiwei@quicinc.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Merge the pmdomain fixes for v6.15-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.16.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The error checking for of_count_phandle_with_args() does not handle
negative error codes correctly. The problem is that "index" is a u32 so
in the condition "if (index >= num_domains)" negative error codes stored
in "num_domains" are type promoted to very high positive values and
"index" is always going to be valid.
Test for negative error codes first and then test if "index" is valid.
Fixes: 3ccf3f0cd197 ("PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/aBxPQ8AI8N5v-7rL@stanley.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sync_file_debug_add() and sync_file_debug_remove() have been unused
since 2016's
commit d4cab38e153d ("staging/android: prepare sync_file for de-staging")
Remove them.
Since sync_file_debug_add was the only thing to add to
sync_file_list_head, the code that dumps it in part of
sync_info_debugfs_show can be removed, and the declaration of
the list and it's associated lock can be removed.
(The 'fences:\n...' marker in that debugfs file is left in
so as not to change the output)
That leaves the sync_print_sync_file() helper unused, and
is thus removed.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250505233838.105668-1-linux@treblig.org
|
|
NIPA tests report that the interface statistics reported
via qstat are lower than those reported via ip link.
Looks like this is because some tests flip the queue
count up and down, and we end up with some of the traffic
accounted on disabled queues.
Add up counters from disabled queues.
Fixes: d888f04c09bb ("virtio-net: support queue stat")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250507003221.823267-3-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The drivers are nearly ordered alphabetically by the symbol name. Fix the
few outliers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250508081706.751209-2-u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
|
We had originally thought to have the mailbox go to ready in the background
while we were doing other things. One issue with this though is that we
can't disable it by clearing the ready state without also blocking
interrupts or calls to mbx_poll as it will just pop back to life during an
interrupt.
In order to prevent that from happening we can pull the code for toggling
to ready out of the interrupt path and instead place it in the
fbnic_mbx_poll_tx_ready path so that it becomes the only spot where the
Rx/Tx can toggle to the ready state. By doing this we can prevent races
where we disable the DMA and/or free buffers only to have an interrupt fire
and undo what we have done.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654722518.499179.11612865740376848478.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This change pulls the call to fbnic_fw_xmit_cap_msg out of
fbnic_mbx_init_desc_ring and instead places it in the polling function for
getting the Tx ready. Doing that we can avoid the potential issue with an
interrupt coming in later from the firmware that causes it to get fired in
interrupt context.
Fixes: 20d2e88cc746 ("eth: fbnic: Add initial messaging to notify FW of our presence")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721876.499179.9839651602256668493.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There were a couple different issues found in fbnic_mbx_poll_tx_ready.
Among them were the fact that we were sleeping much longer than we actually
needed to as the actual FW could respond in under 20ms. The other issue was
that we would just keep polling the mailbox even if the device itself had
gone away.
To address the responsiveness issues we can decrease the sleeps to 20ms and
use a jiffies based timeout value rather than just counting the number of
times we slept and then polled.
To address the hardware going away we can move the check for the firmware
BAR being present from where it was and place it inside the loop after the
mailbox descriptor ring is initialized and before we sleep so that we just
abort and return an error if the device went away during initialization.
With these two changes we see a significant improvement in boot times for
the driver.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721224.499179.2698616208976624755.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There was an issue in that if we were to shutdown we could be left with
a completion in flight as the mailbox went away. To address that I have
added an fbnic_mbx_evict_all_cmpl function that is meant to essentially
create a "broken pipe" type response so that all callers will receive an
error indicating that the connection has been broken as a result of us
shutting down the mailbox.
Fixes: 378e5cc1c6c6 ("eth: fbnic: hwmon: Add completion infrastructure for firmware requests")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654720578.499179.380252598204530873.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fbnic_mbx_flush_tx function had a number of issues.
First, we were waiting 200ms for the firmware to process the packets. We
can drop this to 20ms and in almost all cases this should be more than
enough time. So by changing this we can significantly reduce shutdown time.
Second, we were not making sure that the Tx path was actually shut off. As
such we could still have packets added while we were flushing the mailbox.
To prevent that we can now clear the ready flag for the Tx side and it
should stay down since the interrupt is disabled.
Third, we kept re-reading the tail due to the second issue. The tail should
not move after we have started the flush so we can just read it once while
we are holding the mailbox Tx lock. By doing that we are guaranteed that
the value should be consistent.
Fourth, we were keeping a count of descriptors cleaned due to the second
and third issues called out. That count is not a valid reason to be exiting
the cleanup, and with the tail only being read once we shouldn't see any
cases where the tail moves after the disable so the tracking of count can
be dropped.
Fifth, we were using attempts * sleep time to determine how long we would
wait in our polling loop to flush out the Tx. This can be very imprecise.
In order to tighten up the timing we are shifting over to using a jiffies
value of jiffies + 10 * HZ + 1 to determine the jiffies value we should
stop polling at as this should be accurate within once sleep cycle for the
total amount of time spent polling.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719929.499179.16406653096197423749.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have two issues that need to be addressed in our IRQ handling.
One is the fact that we can end up double-freeing IRQs in the event of an
exception handling error such as a PCIe reset/recovery that fails. To
prevent that from becoming an issue we can use the msix_vector values to
indicate that we have successfully requested/freed the IRQ by only setting
or clearing them when we have completed the given action.
The other issue is that we have several potential races in our IRQ path due
to us manipulating the mask before the vector has been truly disabled. In
order to handle that in the case of the FW mailbox we need to not
auto-enable the IRQ and instead will be enabling/disabling it separately.
In the case of the PCS vector we can mitigate this by unmapping it and
synchronizing the IRQ before we clear the mask.
The general order of operations after this change is now to request the
interrupt, poll the FW mailbox to ready, and then enable the interrupt. For
the shutdown we do the reverse where we disable the interrupt, flush any
pending Tx, and then free the IRQ. I am renaming the enable/disable to
request/free to be equivilent with the IRQ calls being used. We may see
additions in the future to enable/disable the IRQs versus request/free them
for certain use cases.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Fixes: 69684376eed5 ("eth: fbnic: Add link detection")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719271.499179.3634535105127848325.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to prevent the device from throwing spurious writes and/or reads
at us we need to gate the AXI fabric interface to the PCIe until such time
as we know the FW is in a known good state.
To accomplish this we use the mailbox as a mechanism for us to recognize
that the FW has acknowledged our presence and is no longer sending any
stale message data to us.
We start in fbnic_mbx_init by calling fbnic_mbx_reset_desc_ring function,
disabling the DMA in both directions, and then invalidating all the
descriptors in each ring.
We then poll the mailbox in fbnic_mbx_poll_tx_ready and when the interrupt
is set by the FW we pick it up and mark the mailboxes as ready, while also
enabling the DMA.
Once we have completed all the transactions and need to shut down we call
into fbnic_mbx_clean which will in turn call fbnic_mbx_reset_desc_ring for
each ring and shut down the DMA and once again invalidate the descriptors.
Fixes: 3646153161f1 ("eth: fbnic: Add register init to set PCIe/Ethernet device config")
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654718623.499179.7445197308109347982.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Address to issues with the FW mailbox descriptor initialization.
We need to reverse the order of accesses when we invalidate an entry versus
writing an entry. When writing an entry we write upper and then lower as
the lower 32b contain the valid bit that makes the entire address valid.
However for invalidation we should write it in the reverse order so that
the upper is marked invalid before we update it.
Without this change we may see FW attempt to access pages with the upper
32b of the address set to 0 which will likely result in DMAR faults due to
write access failures on mailbox shutdown.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654717972.499179.8083789731819297034.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The following commit:
288a4ff0ad29 ("x86/msr: Move rdtsc{,_ordered}() to <asm/tsc.h>")
removed the <asm/msr.h> include from the accel/habanalabs driver, which broke
the build on UML:
drivers/accel/habanalabs/common/habanalabs_ioctl.c:326:23: error: call to undeclared function 'rdtsc'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
Make the driver depend on 'X86 && X86_64', instead of just 'X86_64',
thus it won't be built on UML.
Suggested-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Oded Gabbay <ogabbay@kernel.org>
Link: https://lore.kernel.org/r/202505080003.0t7ewxGp-lkp@intel.com
|
|
Fix the below sparse warnings:
symbol 'rpcif_impl' was not declared. Should it be static?
symbol 'xspi_impl' was not declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505072013.1EqwjtaR-lkp@intel.com/
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250507162146.140494-1-biju.das.jz@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
When a port gets set up, b53 disables learning and enables the port for
flooding. This can undo any bridge configuration on the port.
E.g. the following flow would disable learning on a port:
$ ip link add br0 type bridge
$ ip link set sw1p1 master br0 <- enables learning for sw1p1
$ ip link set br0 up
$ ip link set sw1p1 up <- disables learning again
Fix this by populating dsa_switch_ops::port_setup(), and set up initial
config there.
Fixes: f9b3827ee66c ("net: dsa: b53: Support setting learning on port")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To allow runtime switching between vlan aware and vlan non-aware mode,
we need to properly keep track of any bridge VLAN configuration.
Likewise, we need to know when we actually switch between both modes, to
not have to rewrite the full VLAN table every time we update the VLANs.
So keep track of the current vlan_filtering mode, and on changes, apply
the appropriate VLAN configuration.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Documentation/networking/switchdev.rst says:
- with VLAN filtering turned off: the bridge is strictly VLAN unaware and its
data path will process all Ethernet frames as if they are VLAN-untagged.
The bridge VLAN database can still be modified, but the modifications should
have no effect while VLAN filtering is turned off.
This breaks if we immediately apply the VLAN configuration, so skip
writing it when vlan_filtering is off.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since we cannot set forwarding destinations per VLAN, we should not have
a VLAN 0 configured, as it would allow untagged traffic to work across
ports on VLAN aware bridges regardless if a PVID untagged VLAN exists.
So remove the VLAN 0 on join, an re-add it on leave. But only do so if
we have a VLAN aware bridge, as without it, untagged traffic would
become tagged with VID 0 on a VLAN unaware bridge.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the
default VLAN enabled so that untagged traffic stays untagged.
So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support.
Fixes: 48aea33a77ab ("net: dsa: b53: Add JOIN_ALL_VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The untagged default VLAN is added to the default vlan, which may be
one, but we modify the VLAN 0 entry on bridge leave.
Fix this to use the correct VLAN entry for the default pvid.
Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Presumably the intention here was to flush the VLAN of the old pvid, not
the added VLAN again, which we already flushed before.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the PVID of ports are only set when adding/updating VLANs with
PVID set or removing VLANs, but not when clearing the PVID flag of a
VLAN.
E.g. the following flow
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master bridge
$ bridge vlan add dev sw1p1 vid 10 pvid untagged
$ bridge vlan add dev sw1p1 vid 10 untagged
Would keep the PVID set as 10, despite the flag being cleared. Fix this
by checking if we need to unset the PVID on vlan updates.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Broadcom management header does not carry the original VLAN tag
state information, just the ingress port, so for untagged frames we do
not know from which VLAN they originated.
Therefore keep the CPU port always tagged except for VLAN 0.
Fixes the following setup:
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master br0
$ bridge vlan add dev br0 pvid untagged self
$ ip link add sw1p2.10 link sw1p2 type vlan id 10
Where VID 10 would stay untagged on the CPU port.
Fixes: 2c32a3d3c233 ("net: dsa: b53: Do not force CPU to be always tagged")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make veth_pool_store detect requested pool changes, close device if
necessary, update pool, and reopen device.
Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506160004.328347-1-davemarq@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A delay unit of 0 is a valid entry, thus it is not valid to check for
unused delays. Instead, check the value field; if that is zero, the
given delay is unset.
Fixes: 4426e6b4ecf6 ("spi: tegra114: Don't fail set_cs_timing when delays are zero")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20250506-spi-tegra114-fixup-v1-1-136dc2f732f3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When sending out any kind of traffic, it is essential that the driver
keeps reporting BQL of the number of bytes that have been sent so that
BQL can track the amount of data in the queue and prevents it from
overflowing. If BQL is not reported, the driver may continue sending
packets even when the queue is full, leading to packet loss, congestion
and decreased network performance. Currently this is missing in
emac_xmit_xdp_frame() and this patch fixes it.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-4-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add __netif_tx_lock() to ensure that only one packet is being
transmitted at a time to avoid race conditions in the netif_txq
struct and prevent packet data corruption. Failing to do so causes
kernel panic with the following error:
[ 2184.746764] ------------[ cut here ]------------
[ 2184.751412] kernel BUG at lib/dynamic_queue_limits.c:99!
[ 2184.756728] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
logs: https://gist.github.com/MeghanaMalladiTI/9c7aa5fc3b7fb03f87c74aad487956e9
The lock is acquired before calling emac_xmit_xdp_frame() and released after the
call returns. This ensures that the TX queue is protected from concurrent access
during the transmission of XDP frames.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-3-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_features demonstrates what all XDP capabilities are supported
on a given network device. The driver needs to set these xdp_features
flag to let the network stack know what XDP features a given driver
is supporting. These flags need to be set for a given ndev irrespective
of any XDP program being loaded or not.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-2-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The official Airoha EN7581 firmware requires adding max_packet field in
ppe_mbox_data struct while the unofficial one used to develop the Airoha
EN7581 flowtable support does not require this field.
This patch does not introduce any real backwards compatible issue since
EN7581 fw is not publicly available in linux-firmware or other
repositories (e.g. OpenWrt) yet and the official fw version will use this
new layout. For this reason this change needs to be backported.
Moreover, make explicit the padding added by the compiler introducing
the rsv array in init_info struct.
At the same time use u32 instead of int for init_info and set_info
struct definitions in ppe_mbox_data struct.
Fixes: 23290c7bc190d ("net: airoha: Introduce Airoha NPU support")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250506-airoha-en7581-fix-ppe_mbox_data-v5-1-29cabed6864d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlike sysfs, the lifetime of configfs objects is controlled by
userspace. There is no mechanism for the kernel to find and delete all
created config-items. Instead, the configfs-tsm-report mechanism has an
expectation that tsm_unregister() can happen at any time and cause
established config-item access to start failing.
That expectation is not fully satisfied. While tsm_report_read(),
tsm_report_{is,is_bin}_visible(), and tsm_report_make_item() safely fail
if tsm_ops have been unregistered, tsm_report_privlevel_store()
tsm_report_provider_show() fail to check for ops registration. Add the
missing checks for tsm_ops having been removed.
Now, in supporting the ability for tsm_unregister() to always succeed,
it leaves the problem of what to do with lingering config-items. The
expectation is that the admin that arranges for the ->remove() (unbind)
of the ${tsm_arch}-guest driver is also responsible for deletion of all
open config-items. Until that deletion happens, ->probe() (reload /
bind) of the ${tsm_arch}-guest driver fails.
This allows for emergency shutdown / revocation of attestation
interfaces, and requires coordinated restart.
Fixes: 70e6f7e2b985 ("configfs-tsm: Introduce a shared ABI for attestation reports")
Cc: stable@vger.kernel.org
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Sami Mujawar <sami.mujawar@arm.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reported-by: Cedric Xing <cedric.xing@intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Link: https://patch.msgid.link/20250430203331.1177062-1-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The "intf" list iterator is an invalid pointer if the correct
"intf->intf_num" is not found. Calling atomic_dec(&intf->nr_users) on
and invalid pointer will lead to memory corruption.
We don't really need to call atomic_dec() if we haven't called
atomic_add_return() so update the if (intf->in_shutdown) path as well.
Fixes: 8e76741c3d8b ("ipmi: Add a limit on the number of users that may use IPMI")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Message-ID: <aBjMZ8RYrOt6NOgi@stanley.mountain>
Signed-off-by: Corey Minyard <corey@minyard.net>
|
|
It's available, remove all the duplicate code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Don't have the other users that do things at panic time (the watchdog)
do all this themselves, provide a function to do it.
Also, with the new design where most stuff happens at thread context,
a few things needed to be fixed to avoid doing locking in a panic
context.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
It was possible for the SSIF thread to stop and quit before the
kthread_stop() call because ssif->stopping was set before the
stop. So only exit the SSIF thread is kthread_should_stop()
returns true.
There is no need to wake the thread, as the wait will be interrupted
by kthread_stop().
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Check to see if they have been destroyed before trying to deliver a
message.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
It is possible in some situations that IPMI devices won't get started up
properly. This change makes it so all non-duplicate devices will get
started up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
If we get a command from a LAN channel, return an error instead of just
throwing it away.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
This makes sure any outstanding messages are returned to the user before
the interface is cleaned up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
It's no longer used.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
The lower level interface shouldn't attempt to unregister if it has a
callback in the pending queue.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Messages already have a refcount for the user, so there's no need to
account for a new one.
As part of this, grab a refcount to the interface when processing
received messages. The messages can be freed there, cause the user
then the interface to be freed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Now that SRCU is gone from IPMI, it can no longer be sloppy about
locking. Use the users mutex now when sending a message, not the big
ipmi_interfaces mutex, because it can result in a recursive lock. The
users mutex will work because the interface destroy code claims it after
setting the interface in shutdown mode.
Also, due to the same changes, rework the refcounting on users and
interfaces. Remove the refcount to an interface when the user is
freed, not when it is destroyed. If the interface is destroyed
while the user still exists, the user will still point to the
interface to test that it is valid if the user tries to do anything
but delete the user.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
When run to completion is set, don't call things that will claim
mutexes or call user callbacks.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Now that the msghandler does all callbacks in user threads, there is
no need to have a lock any more, a mutex will work fine.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
