| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
|
|
Pull MIPS fixes from Ralf Baechle:
"This is the first round of fixes and tying up loose ends for MIPS.
- plenty of fixes for build errors in specific obscure configurations
- remove redundant code on the Lantiq platform
- removal of a useless SEAD I2C driver that was causing a build issue
- fix an earlier TLB exeption handler fix to also work on Octeon.
- fix ISA level dependencies in FPU emulator's instruction decoding.
- don't hardcode kernel command line in Octeon software emulator.
- fix an earlier fix for the Loondson 2 clock setting"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: SEAD3: Fix I2C device registration.
MIPS: SEAD3: Nuke PIC32 I2C driver.
MIPS: ftrace: Fix a microMIPS build problem
MIPS: MSP71xx: Fix build error
MIPS: Malta: Do not build the malta-amon.c file if CMP is not enabled
MIPS: Prevent compiler warning from cop2_{save,restore}
MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidle
MIPS: idle: Remove leftover __pastwait symbol and its references
MIPS: Sibyte: Include the swarm subdir to the sb1250 LittleSur builds
MIPS: ptrace.h: Add a missing include
MIPS: ath79: Fix compilation error when CONFIG_PCI is disabled
MIPS: MSP71xx: Remove compilation error when CONFIG_MIPS_MT is present
MIPS: Octeon: Remove special case for simulator command line.
MIPS: tlbex: Properly fix HUGE TLB Refill exception handler
MIPS: loongson2_cpufreq: Fix CPU clock rate setting mismerge
pci: pci-lantiq: remove duplicate check on resource
MIPS: Lasat: Add missing CONFIG_PROC_FS dependency to PICVUE_PROC
MIPS: cp1emu: Fix ISA restrictions for cop1x_op instructions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
* tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Allocate memory for physdev_pci_device_add's optarr
x86/xen: panic on bad Xen-provided memory map
x86/xen: Fix incorrect per_cpu accessor in xen_clocksource_read()
x86/xen: avoid race in p2m handling
x86/xen: delay construction of mfn_list_list
x86/xen: avoid writing to freed memory after race in p2m handling
xen/balloon: Don't continue ballooning when BP_ECANCELED is encountered
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random updates from Ted Ts'o:
"This adds a memzero_explicit() call which is guaranteed not to be
optimized away by GCC. This is important when we are wiping
cryptographically sensitive material"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
crypto: memzero_explicit - make sure to clear out sensitive data
random: add and use memzero_explicit() for clearing data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This is material that didn't make it to my 3.18-rc1 pull request for
various reasons, mostly related to timing and travel (LinuxCon EU /
LPC) plus a couple of fixes for recent bugs.
The only really new thing here is the PM QoS class for memory
bandwidth, but it is simple enough and users of it will be added in
the next cycle. One major change in behavior is that platform devices
enumerated by ACPI will use 32-bit DMA mask by default. Also included
is an ACPICA update to a new upstream release, but that's mostly
cleanups, changes in tools and similar. The rest is fixes and
cleanups mostly.
Specifics:
- Fix for a recent PCI power management change that overlooked the
fact that some IRQ chips might not be able to configure PCIe PME
for system wakeup from Lucas Stach.
- Fix for a bug introduced in 3.17 where acpi_device_wakeup() is
called with a wrong ordering of arguments from Zhang Rui.
- A bunch of intel_pstate driver fixes (all -stable candidates) from
Dirk Brandewie, Gabriele Mazzotta and Pali Rohár.
- Fixes for a rather long-standing problem with the OOM killer and
the freezer that frozen processes killed by the OOM do not actually
release any memory until they are thawed, so OOM-killing them is
rather pointless, with a couple of cleanups on top (Michal Hocko,
Cong Wang, Rafael J Wysocki).
- ACPICA update to upstream release 20140926, inlcuding mostly
cleanups reducing differences between the upstream ACPICA and the
kernel code, tools changes (acpidump, acpiexec) and support for the
_DDN object (Bob Moore, Lv Zheng).
- New PM QoS class for memory bandwidth from Tomeu Vizoso.
- Default 32-bit DMA mask for platform devices enumerated by ACPI
(this change is mostly needed for some drivers development in
progress targeted at 3.19) from Heikki Krogerus.
- ACPI EC driver cleanups, mostly related to debugging, from Lv
Zheng.
- cpufreq-dt driver updates from Thomas Petazzoni.
- powernv cpuidle driver update from Preeti U Murthy"
* tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
intel_pstate: Correct BYT VID values.
intel_pstate: Fix BYT frequency reporting
intel_pstate: Don't lose sysfs settings during cpu offline
cpufreq: intel_pstate: Reflect current no_turbo state correctly
cpufreq: expose scaling_cur_freq sysfs file for set_policy() drivers
cpufreq: intel_pstate: Fix setting max_perf_pct in performance policy
PCI / PM: handle failure to enable wakeup on PCIe PME
ACPI: invoke acpi_device_wakeup() with correct parameters
PM / freezer: Clean up code after recent fixes
PM: convert do_each_thread to for_each_process_thread
OOM, PM: OOM killed task shouldn't escape PM suspend
freezer: remove obsolete comments in __thaw_task()
freezer: Do not freeze tasks killed by OOM killer
ACPI / platform: provide default DMA mask
cpuidle: powernv: Populate cpuidle state details by querying the device-tree
cpufreq: cpufreq-dt: adjust message related to regulators
cpufreq: cpufreq-dt: extend with platform_data
cpufreq: allow driver-specific data
ACPI / EC: Cleanup coding style.
ACPI / EC: Refine event/query debugging messages.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
|
|
* pm-cpuidle:
cpuidle: powernv: Populate cpuidle state details by querying the device-tree
* pm-cpufreq:
intel_pstate: Correct BYT VID values.
intel_pstate: Fix BYT frequency reporting
intel_pstate: Don't lose sysfs settings during cpu offline
cpufreq: intel_pstate: Reflect current no_turbo state correctly
cpufreq: expose scaling_cur_freq sysfs file for set_policy() drivers
cpufreq: intel_pstate: Fix setting max_perf_pct in performance policy
cpufreq: cpufreq-dt: adjust message related to regulators
cpufreq: cpufreq-dt: extend with platform_data
cpufreq: allow driver-specific data
|
|
* acpi-pm:
ACPI: invoke acpi_device_wakeup() with correct parameters
* pm-genirq:
PCI / PM: handle failure to enable wakeup on PCIe PME
|
|
* acpi-ec:
ACPI / EC: Cleanup coding style.
ACPI / EC: Refine event/query debugging messages.
ACPI / EC: Add detailed command/query debugging information.
ACPI / EC: Enhance the logs to apply to QR_EC transactions.
ACPI / EC: Add CPU ID to debugging messages.
* acpi-platform:
ACPI / platform: provide default DMA mask
|
|
Using a VID value that is not high enough for the requested P state can
cause machine checks. Add a ceiling function to ensure calulated VIDs
with fractional values are set to the next highest integer VID value.
The algorythm for calculating the non-trubo VID from the BIOS writers
guide is:
vid_ratio = (vid_max - vid_min) / (max_pstate - min_pstate)
vid = ceiling(vid_min + (req_pstate - min_pstate) * vid_ratio)
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
BYT has a different conversion from P state to frequency than the core
processors. This causes the min/max and current frequency to be
misreported on some BYT SKUs. Tested on BYT N2820, Ivybridge and
Haswell processors.
Link: https://bugzilla.yoctoproject.org/show_bug.cgi?id=6663
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The user may have custom settings don't destroy them during suspend.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80651
Reported-by: Tobias Jakobi <liquid.acid@gmx.net>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some BIOSes modify the state of MSR_IA32_MISC_ENABLE_TURBO_DISABLE
based on the current power source for the system battery AC vs
battery. Reflect the correct current state and ability to modify the
no_turbo sysfs file based on current state of
MSR_IA32_MISC_ENABLE_TURBO_DISABLE.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=83151
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the core does not expose scaling_cur_freq for set_policy()
drivers this breaks some userspace monitoring tools.
Change the core to expose this file for all drivers and if the
set_policy() driver supports the get() callback use it to retrieve the
current frequency.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73741
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Code which changes policy to powersave changes also max_policy_pct based on
max_freq. Code which change max_perf_pct has upper limit base on value
max_policy_pct. When policy is changing from powersave back to performance
then max_policy_pct is not changed. Which means that changing max_perf_pct is
not possible to high values if max_freq was too low in powersave policy.
Test case:
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
800000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
100
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 20 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
800000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
20
$ echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 3300000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 100 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
24
And now intel_pstate driver allows to set maximal value for max_perf_pct based
on max_policy_pct which is 24 for previous powersave max_freq 800000.
This patch will set default value for max_policy_pct when setting policy to
performance so it will allow to set also max value for max_perf_pct.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"Fix potential compile problem for menf21bmc hwmon driver"
* tag 'hwmon-for-linus-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (menf21bmc) Include linux/err.h
|
|
If the irqchip handling the PCIe PME interrupt is not able
to enable interrupt wakeup we should properly reflect this
in the PME suspend status.
This fixes a kernel warning on resume, where it would try
to disable the irq wakeup that failed to be activated while
suspending, for example:
WARNING: CPU: 0 PID: 609 at kernel/irq/manage.c:536 irq_set_irq_wake+0xc0/0xf8()
Unbalanced IRQ 384 wake disable
Fixes: 76cde7e49590 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: Richard Zhu <richard.zhu@freescale.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix a bug that invokes acpi_device_wakeup() with wrong parameters.
Fixes: f35cec255557 (ACPI / PM: Always enable wakeup GPEs when enabling device wakeup)
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"Intel, nouveau, radeon and qxl.
Mostly for bugs introduced in the merge window, nothing too shocking"
[ And one cirrus fix added later and not mentioned in the pull request.. - Linus ]
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/cirrus: bind also to qemu-xen-traditional
qxl: don't create too large primary surface
drm/nouveau: fix regression on agp boards
drm/gt215/gr: fix initialisation on gddr5 boards
drm/radeon: reduce sparse false positive warnings
drm/radeon: fix vm page table block size calculation
drm/ttm: Don't evict BOs outside of the requested placement range
drm/ttm: Don't skip fpfn check if lpfn is 0 in ttm_bo_mem_compat
drm/radeon: use gart memory for DMA ring tests
drm/radeon: fix speaker allocation setup
drm/radeon: initialize sadb to NULL in the audio code
drm/i915: fix short vs. long hpd detection
drm/i915: Don't trust the DP_DETECT bit for eDP ports on CHV
Revert "drm/radeon/dpm: drop clk/voltage dependency filters for SI"
Revert "drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table"
drm/i915: properly reenable gen8 pipe IRQs
drm/i915: Move DIV_ROUND_CLOSEST_ULL macro to header
drm/i915: intel_backlight scale() math WA
|
|
The MIPS_CPS_PM and MIPS_CPS_CPUIDLE implementation should depend
on the MIPS_CPS symbol to avoid the following build problem
arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
arch/mips/kernel/pm-cps.c:164:26: error: 'cpu_coherent_mask' undeclared
(first use in this function)
cpumask_clear_cpu(cpu, &cpu_coherent_mask);
^
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7798/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
physdev_pci_device_add's optarr[] is a zero-sized array and therefore
reference to add.optarr[0] is accessing memory that does not belong to
the 'add' variable.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Commit 3dcf63677d4e ("xen/balloon: cancel ballooning if adding new
memory failed") makes reserve_additional_memory() return BP_ECANCELED
when an error is encountered. This error, however, is ignored by the
caller (balloon_process()) since it is overwritten by subsequent call
to update_schedule(). This results in continuous attempts to add more
memory, all of which are likely to fail again.
We should stop trying to schedule next iteration of ballooning when
the current one has failed.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
qemu as used by xend/xm toolstack uses a different subvendor id.
Bind the drm driver also to this emulated card.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Limit primary to qemu vgamem size, to avoid reaching
qemu guest bug "requested primary larger than framebuffer"
on resizing screen too large to fit.
Remove unneeded and misleading variables.
Related to:
https://bugzilla.redhat.com/show_bug.cgi?id=1127552
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Most devices are configured for 32-bit DMA addresses.
Setting the mask to 32-bit here removes the need for the
drivers to do it separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target updates for v3.18-rc2 code. These where
originally destined for -rc1, but due to the combination of travel
last week for KVM Forum and my mistake of taking the three week merge
window literally, the pull request slipped.. Apologies for that.
Things where reasonably quiet this round. The highlights include:
- New userspace backend driver (target_core_user.ko) by Shaohua Li
and Andy Grover
- A number of cleanups in target, iscsi-taret and qla_target code
from Joern Engel
- Fix an OOPs related to queue full handling with CHECK_CONDITION
status from Quinn Tran
- Fix to disable TX completion interrupt coalescing in iser-target,
that was causing problems on some hardware
- Fix for PR APTPL metadata handling with demo-mode ACLs
I'm most excited about the new backend driver that uses UIO + shared
memory ring to dispatch I/O and control commands into user-space.
This was probably the most requested feature by users over the last
couple of years, and opens up a new area of development + porting of
existing user-space storage applications to LIO. Thanks to Shaohua +
Andy for making this happen.
Also another honorable mention, a new Xen PV SCSI driver was merged
via the xen/tip.git tree recently, which puts us now at 10 target
drivers in upstream! Thanks to David Vrabel + Juergen Gross for their
work to get this code merged"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
target/file: fix inclusive vfs_fsync_range() end
iser-target: Disable TX completion interrupt coalescing
target: Add force_pr_aptpl device attribute
target: Fix APTPL metadata handling for dynamic MappedLUNs
qla_target: don't delete changed nacls
target/user: Recalculate pad size inside is_ring_space_avail()
tcm_loop: Fixup tag handling
iser-target: Fix smatch warning
target/user: Fix up smatch warnings in tcmu_netlink_event
target: Add a user-passthrough backstore
target: Add documentation on the target userspace pass-through driver
uio: Export definition of struct uio_device
target: Remove unneeded check in sbc_parse_cdb
target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE
qla_target: rearrange struct qla_tgt_prm
qla_target: improve qlt_unmap_sg()
qla_target: make some global functions static
qla_target: remove unused parameter
target: simplify core_tmr_abort_task
target: encapsulate smp_mb__after_atomic()
...
|
|
Pull email address change from Boaz Harrosh.
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
Boaz Harrosh - fix email in Documentation
Boaz Harrosh - Fix broken email address
MAINTAINERS: Change Boaz Harrosh's email
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
|
|
Pull watchdog updates from Wim Van Sebroeck:
- new Cadence WDT driver
- new Ricoh RN5T618 watchdog
- new DA9063 PMIC watchdog driver
- new Meson WDT driver
- add restart handling code
- fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
watchdog: meson: remove magic value for reboot
watchdog: Let XILINX_WATCHDOG and TEGRA_WATCHDOG depend on HAS_IOMEM
watchdog: sunxi: Add A31 watchdog support
watchdog: sunxi: support parameterized compatible strings
watchdog: imx2_wdt: add restart handler support
watchdog: qcom: register a restart notifier
watchdog: s3c2410: add restart handler
watchdog: dw_wdt: add restart handler support
ARM: defconfig: update multi_v7_defconfig
ARM: meson: add watchdog driver
ARM: docs: add documentation binding for meson watchdog
stmp3xxx_rtc_wdt: Add suspend/resume PM support
watchdog: Add DA9063 PMIC watchdog driver.
watchdog: add driver for Ricoh RN5T618 watchdog
watchdog: s3c2410_wdt: Add support for Watchdog device on Exynos7
watchdog: qcom: document device tree bindings
watchdog: qcom: add support for KPSS WDT
watchdog: dw_wdt: initialise TOP_INIT in dw_wdt_set_top()
devicetree: Add Cadence WDT devicetree bindings documentation
watchdog: Add Cadence WDT driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED update from Bryan Wu:
"Basically we have some bug fixing and clean up and one big thing is we
start to merge patch to add support LED Flash class"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: gpio: cleanup the leds-gpio driver
led: gpio: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
led: gpio: Sort include headers alphabetically
leds: Improve and export led_update_brightness
leds: trigger: gpio: fix warning in gpio trigger for gpios whose accessor function may sleep
leds: lp3944: fix sparse warning
leds: avoid using DEVICE_ATTR macro for max_brightness attribute
leds: make brightness type consistent across whole subsystem
leds: Reorder include directives
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"There are no new drivers here, only a couple of fixes all over the
place"
* tag 'pwm/for-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Let PWM_CLPS711X depend on HAS_IOMEM
pwm: atmel: Fix calculation of prescale value
pwm: Fix uninitialized warnings in pwm_get()
pwm: rockchip: Allow polarity invert on rk3288
pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2
pwm: imx: Cleanup indentation for register definitions
pwm: imx: Fix the macro MX3_PWMCR_PRESCALER(x) definition
pwm: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
pwm: lpss: make it buildable only on X86
pwm: lpss: use c99 initializers in structures
pwm: lpss: Fix build failure on PowerPC
pwm: lpss: pci: Move to use pcim_enable_device()
pwm: lpss: Properly split driver to parts
pwm: lpss: Add ACPI and PCI IDs for Intel Braswell
pwm: fsl-ftm: Select REGMAP_MMIO
pwm: fsl-ftm: Document 'big-endian' property
pwm: fsl-ftm: Convert to direct regmap API usage
pwm: fsl-ftm: Clean up the code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"One patch to enable the BPF system call and three more bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix kprobes dependency
s390: wire up bpf syscall
s390/mm: fixing calls of pte_unmap_unlock
s390/hmcdrv: Restrict s390 HMC driver to S390 arch
|
|
We hard code the metrics relevant for cpuidle states in the kernel today.
Instead pick them up from the device tree so that they remain relevant
and updated for the system that the kernel is running on.
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq-dt driver tries to get a regulator for each CPU. This
regulator is optional, but when not present, a scary message "failed
to get cpuX regulator" is displayed. To solve this, we reduce the
severity of the message from dev_warn() to dev_dbg() and we reword the
message to not be as scary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This commit extends the cpufreq-dt driver to take a platform_data
structure. This structure is for now used to tell the cpufreq-dt
driver the layout of the clocks on the platform, i.e whether all CPUs
share the same clock or whether each CPU has a separate clock.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This commit extends the cpufreq_driver structure with an additional
'void *driver_data' field that can be filled by the ->probe() function
of a cpufreq driver to pass additional custom information to the
driver itself.
A new function called cpufreq_get_driver_data() is added to allow a
cpufreq driver to retrieve those driver data, since they are typically
needed from a cpufreq_policy->init() callback, which does not have
access to the cpufreq_driver structure. This function call is similar
to the existing cpufreq_get_current_driver() function call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch cleans up the following coding style issues that are detected by
scripts/checkpatch.pl:
ERROR: code indent should use tabs where possible
ERROR: "foo * bar" should be "foo *bar"
WARNING: Missing a blank line after declarations
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
WARNING: void function return statements are not generally useful
WARNING: else is not generally useful after a break or return
WARNING: break is not useful after a goto or return
WARNING: braces {} are not necessary for single statement blocks
WARNING: line over 80 characters
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch refines event/query debugging messages to use a unified format
as commands. Developers can clearly find different processes by checking
different log seperators. No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Developers really don't need to translate EC commands in mind. This patch
adds detailed debugging information for the EC commands.
The address can be found in the follow-up sequential EC_DATA(W) accesses,
thus this patch also removes some of the redundant address information.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently some logs are applied to new transactions, but QR_EC transactions
are not included. This patch merges the code path to make the logs also
applying to the QR_EC transactions.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds CPU ID to the context entries' debugging output. no
functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adds support for both iASL and the disassembler to create a hardware
and connection summary mapfile (via the -lm option.)
Linux isn't affected by this patch because iASL is not in the Linux
upstream.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
renaming.
This patch is partial linuxized result of the following ACPICA commit:
ACPICA commit: a73b66c6aa1846d055bb6390d9c9b9902f7d804d
Subject: Add "has handler" flag to event/gpe status interfaces.
This change adds a new flag, ACPI_EVENT_FLAGS_HAS_HANDLER to the
acpi_get_event_status and acpi_get_gpe_status external interfaces. It
is set if the event/gpe currently has a handler associated with it.
This patch contains the code to rename ACPI_EVENT_FLAG_HANDLE to
ACPI_EVENT_FLAG_HAS_HANDLER, and the corresponding updates of its usages.
Link: https://github.com/acpica/acpica/commit/a73b66c6
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
support.
This patch is a partial linuxized result of the following ACPICA commit:
ACPICA commit: a73b66c6aa1846d055bb6390d9c9b9902f7d804d
Subject: Add "has handler" flag to event/gpe status interfaces.
This change adds a new flag, ACPI_EVENT_FLAGS_HAS_HANDLER to the
acpi_get_event_status and acpi_get_gpe_status external interfaces. It
is set if the event/gpe currently has a handler associated with it.
This commit back ports ACPI_EVENT_FLAG_HANDLE from Linux upstream to
ACPICA, the flag along with its support code currently can only be found
in the Linux upstream and is used by the ACPI sysfs GPE interfaces and
the ACPI bus scanning support.
Link: https://github.com/acpica/acpica/commit/a73b66c6
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The originally_enabled check is not paired between
acpi_install_gpe_handler() and acpi_remove_gpe_handler().
In ACPICA upstream, there is code to protect original enabled state for
ACPI_GPE_DISPATCH_NOTIFY and this commit fixes an issue for this feature.
Link: https://github.com/acpica/acpica/commit/967f314c
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is a sanity check in ACPICA upstream, complaining mis-matched
interrupt type for originally enabled GPEs that are going to be dispatched
by OSPM handlers. This is only a warning message noting developers such
conflict between BIOS and OSPM. This patch ports this warning message from
ACPICA upstream to reduce source code difference between Linux and ACPICA
upstream.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch reduces indent divergences first in order to reduce human
intervention work for the follow-up linuxized event patches.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The acpidump currently always uses ACPI 2.0 format to dump RSDP, this patch
adds ACPI 1.0 RSDP support.
Link: https://bugs.acpica.org/show_bug.cgi?id=1097
Link: https://bugs.acpica.org/show_bug.cgi?id=1103
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Rudolf Marek <r.marek@assembler.cz>
Reported-and-tested-by: Rafal <fatwildcat@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
