| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These were never used in the tree, and are marked as reserved
in the IEEE 802.11 documentation (ANA).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
iwlwifi:
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
brcmfmac:
* support NVRAM loading for bcm47xx platform
* new debugfs entry for msgbuf protocol layer used with PCIe devices
ath10k:
* add spectral scan support for qca99x0
* add qca6164 support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Major changes in ath10k:
* add spectral scan support for qca99x0
* add qca6164 support
|
|
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6cd ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c2f ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67af ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.
Fixes: e04cafbc38c7 ("ath10k: fix peer limit enforcement")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
posted_index is RO in firmware. We need not do ioread everytime to get
posted index. Store posted index locally.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The r8169 driver collects statistical information returned by
@get_stats64 by counting them in the driver itself, even though many
(but not all) of the values are already collected by tally counters
(TCs) in the NIC. Some of these TC values are not returned by
@get_stats64. Especially the received multicast packages are missing
from /proc/net/dev.
Rectify this by fetching the TCs and returning them from
rtl8169_get_stats64.
The counters collected in the driver obviously disappear as soon as the
driver is unloaded so after a driver is loaded the counters always start
at 0. The TCs on the other hand are only reset by a power cycle. Without
further considerations the values collected by the driver would not match
up against the TC values.
This patch introduces a new function rtl8169_reset_counters which
resets the TCs. Also, since rtl8169_reset_counters shares most of
its code with rtl8169_update_counters, refactor the shared code into
two new functions rtl8169_map_counters and rtl8169_unmap_counters.
Unfortunately chip versions prior to RTL_GIGA_MAC_VER_19 don't allow
to reset the TCs programatically. Therefore introduce an addition to
the rtl8169_private struct and a function rtl8169_init_counter_offsets
to store the TCs at first rtl_open. Use these values as offsets in
rtl8169_get_stats64. Propagate a failure to reset *and* update the
counters up to rtl_open and emit a warning message, if so.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let packets move from one netns to the other at PPP encapsulation and
decapsulation time.
PPP units and channels remain in the netns in which they were
originally created. Only the net_device may move to a different
namespace. Cross netns handling is thus transparent to lower PPP
layers (PPPoE, L2TP, etc.).
PPP devices are automatically unregistered when their netns gets
removed. So read() and poll() on the unit file descriptor will
respectively receive EOF and POLLHUP. Channels aren't affected.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claim the emac sram ourselves, rather then relying on the bootloader
having mapped the sram to the emac controller during boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To avoid multiply/division operations on the data path,
we hold a {channel, tc}==>txq mapping table.
We held this mapping table inside the channel object that is
being destroyed upon some configuration operations (e.g MTU change).
So in case ndo_select_queue occurs during such a configuration operation,
it may access a NULL channel pointer, resulting in kernel panic.
To fix this issue we moved the {channel, tc}==>txq mapping table
outside the channel object so that it will be available also
during such configuration operations.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak")
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Host platforms such as routers supported by OpenWRT can
support NVRAM reading directly from internal NVRAM store.
With this patch the nvram load routines will fall back to
this method when there is no nvram file and support is
available in the kernel.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The event mask length is determined by the highest event number
that is specified in the driver. When this length is shorter than
firmware expects setting event mask will fail and device becomes
pretty useless. This issue was reported with bcm4339 firmware that
was recently released.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_flowring_block blocks the last active flowring under the same
interface instead of the one provided by caller. This could lead to a
dead lock of netif stop if there are more than one flowring under the
interface and the traffic is high enough so brcmf_flowring_enqueue can
not unblock the ring right away.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use cfg80211_check_combinations() so we can bail out early when an
interface add or change results in an invalid combination.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Expose ring buffer read/write pointers and other useful statistics
through debugfs.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The interface combination provided by brcmfmac did not truly reflect
the combinations supported by driver and/or firmware.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Broadcom is working on better reflection of interface combinations. With
upcoming patches we may have 1st combination supporting less interfaces
than others.
To don't run out of addresses check all combinations to find the one
with the greatest max_interfaces value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
drivers/net/wireless/rtlwifi/rtl8192ee/phy.c:856:2-3: Unneeded semicolon
drivers/net/wireless/rtlwifi/rtl8192ee/phy.c:492:3-4: Unneeded semicolon
drivers/net/wireless/rtlwifi/rtl8192ee/phy.c:452:3-4: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
current code will handle -ETIMEDOUT as success which is probalbly wrong.
According to this comment I assume it is safe to handle -ETIMEDOUT as false:
drivers/net/wireless/ath/ath9k/calib.c
290 /*
291 * We timed out waiting for the noisefloor to load, probably due to an
292 * in-progress rx. Simply return here and allow the load plenty of time
293 * to complete before the next calibration interval. We need to avoid
294 * trying to load -50 (which happens below) while the previous load is
295 * still in progress as this can cause rx deafness. Instead by returning
296 * here, the baseband nf cal will just be capped by our present
297 * noisefloor until the next calibration timer.
298 */
Since no other error wariants are present, this patch is checking only
for (ret <= 0).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
|
|
This patch adds implementation for ethtool support.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds implementation of handling IRQ
of other receiver's receive cancellation request.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds epstop_task.
This task is used to process other receiver's
cancellation request.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds update_zone_task.
Zoning information can be changed by user.
This task is used to monitor if zoning information is
changed or not.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds unshare_watch_task.
Shared buffer's status can be changed into unshared.
This task is used to monitor shared buffer's status.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds force_close_task.
This task is used to close network device forcibly.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds interrupt_watch_task.
This task is used to prevent delay of interrupts.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_vlan_rx_add_vid and
net_device_ops.ndo_vlan_rx_kill_vid callback.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_tx_timeout callback.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_change_mtu.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_get_stats64 callback.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds NAPI polling function and receive related work.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds tx_stall_task.
When receiver's buffer is full, sender stops
its tx queue. This task is used to monitor
receiver's status and when receiver's buffer
is avairable, it resumes tx queue.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add raise_intr_rxdata_task.
Extended Socket Network Device is shared memory
based, so someone's transmission denotes other's
reception. In order to notify receivers, sender
has to raise interruption of receivers.
raise_intr_rxdata_task does this work.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_start_xmit callback,
which is called when sending packets.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net_device_ops.ndo_open and .ndo_stop
callback. These function is called when network device
activation and deactivation.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds buffer address regist/unregistration routine.
This function is mainly invoked when network device's
activation (open) and deactivation (close)
in order to retist/unregist shared buffer address.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds ES information acquisition routine.
ES information can be retrieved issuing information
request command. ES information includes which
receiver is same zone.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements platform_driver's .probe and .remove
routine, and also adds board specific private data structure.
This driver registers net_device at platform_driver's .probe
routine and unregisters net_device at its .remove routine.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds hardware cleanup routine to be
invoked at driver's .remove routine.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds hardware initialization routine to be
invoked at driver's .probe routine.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the basic code of FUJITSU Extended Socket
Network Device driver.
When "PNP0C02" is found in ACPI DSDT, it evaluates "_STR"
to check if "PNP0C02" is for Extended Socket device driver
and retrieves ACPI resource information. Then creates
platform_device.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
