| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since mlxsw_sp_fib_create() and mlxsw_sp_mr_table_create()
use ERR_PTR macro to propagate int err through return of a pointer,
the return value is not NULL in case of failure. So if one
of the calls fails, one of vr->fib4, vr->fib6 or vr->mr4_table
is not NULL and mlxsw_sp_vr_is_used wrongly assumes
that vr is in use which leads to crash like following one:
[ 1293.949291] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c9
[ 1293.952729] IP: mlxsw_sp_mr_table_flush+0x15/0x70 [mlxsw_spectrum]
Fix this by using local variables to hold the pointers and set vr->*
only in case everything went fine.
Fixes: 76610ebbde18 ("mlxsw: spectrum_router: Refactor virtual router handling")
Fixes: a3d9bc506d64 ("mlxsw: spectrum_router: Extend virtual routers with IPv6 support")
Fixes: d42b0965b1d4 ("mlxsw: spectrum_router: Add multicast routes notification handling functionality")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent a kernel panic on reboot if ptp_clock is NULL by checking
the ptp pointer before using it.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Fixes: 8c56df372bc1 ("net: add support for Cavium PTP coprocessor")
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The control channel calls registered callbacks when control messages
such as XDomain protocol messages are received. The control channel
handling is done in a worker running on system workqueue which means the
networking driver can't run tear down flow which includes sending
disconnect request and waiting for a reply in the same worker. Otherwise
reply is never received (as the work is already running) and the
operation times out.
To fix this run disconnect ThunderboltIP flow asynchronously once
ThunderboltIP logout message is received.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When suspending to mem or disk the Thunderbolt controller typically goes
down as well tearing down the connection automatically. However, when
suspend to idle is used this does not happen so we need to make sure the
connection is properly disconnected before it can be re-established
during resume.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if Wake-on-LAN is enabled, the SH-ETH device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commits 91c719f5ec6671f7 ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") and 744dddcae84441b1 ("clk:
renesas: mstp: Keep wakeup sources active during system suspend"), this
workaround is no longer needed. Hence remove all explicit clock
handling to keep the device active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if Wake-on-LAN is enabled, the EtherAVB device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commit 91c719f5ec6671f7 ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") , this workaround is no longer
needed. Hence remove all explicit clock handling to keep the device
active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When forcing a specific link mode, the PHY driver must clear the
existing speed and duplex bits in BMCR while preserving some other
control bits. This logic was accidentally inverted with the introduction
of phy_modify().
Fixes: fea23fb591cc ("net: phy: convert read-modify-write to phy_modify()")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more poll annotation updates from Al Viro:
"This is preparation to solving the problems you've mentioned in the
original poll series.
After this series, the kernel is ready for running
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
as a for bulk search-and-replace.
After that, the kernel is ready to apply the patch to unify
{de,}mangle_poll(), and then get rid of kernel-side POLL... uses
entirely, and we should be all done with that stuff.
Basically, that's what you suggested wrt KPOLL..., except that we can
use EPOLL... instead - they already are arch-independent (and equal to
what is currently kernel-side POLL...).
After the preparations (in this series) switch to returning EPOLL...
from ->poll() instances is completely mechanical and kernel-side
POLL... can go away. The last step (killing kernel-side POLL... and
unifying {de,}mangle_poll() has to be done after the
search-and-replace job, since we need userland-side POLL... for
unified {de,}mangle_poll(), thus the cherry-pick at the last step.
After that we will have:
- POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
->poll() still using those will be caught by sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly)"
* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
annotate ep_scan_ready_list()
ep_send_events_proc(): return result via esed->res
preparation to switching ->poll() to returning EPOLL...
add EPOLLNVAL, annotate EPOLL... and event_poll->event
use linux/poll.h instead of asm/poll.h
xen: fix poll misannotation
smc: missing poll annotations
|
|
Pull block fixes from Jens Axboe:
"A few fixes to round off the merge window on the block side:
- a set of bcache fixes by way of Michael Lyle, from the usual bcache
suspects.
- add a simple-to-hook-into function for bpf EIO error injection.
- fix blk-wbt that mischarectized flushes as reads. Improve the logic
so that flushes and writes are accounted as writes, and only reads
as reads. From me.
- fix requeue crash in BFQ, from Paolo"
* tag 'for-linus-20180210' of git://git.kernel.dk/linux-block:
block, bfq: add requeue-request hook
bcache: fix for data collapse after re-attaching an attached device
bcache: return attach error when no cache set exist
bcache: set writeback_rate_update_seconds in range [1, 60] seconds
bcache: fix for allocator and register thread race
bcache: set error_limit correctly
bcache: properly set task state in bch_writeback_thread()
bcache: fix high CPU occupancy during journal
bcache: add journal statistic
block: Add should_fail_bio() for bpf error injection
blk-wbt: account flush requests correctly
|
|
Pull x86 platform driver updates from Darren Hart:
"Mellanox fixes and new system type support.
Mostly data for new system types with a correction and an
uninitialized variable fix"
[ Pulling from github because git.infradead.org currently seems to be
down for some reason, but Darren had a backup location - Linus ]
* tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86:
platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
platform/x86: mlx-platform: Add support for new msn201x system type
platform/x86: mlx-platform: Add support for new msn274x system type
platform/x86: mlx-platform: Fix power cable setting for msn21xx family
platform/x86: mlx-platform: Add define for the negative bus
platform/x86: mlx-platform: Use defines for bus assignment
platform/mellanox: mlxreg-hotplug: Fix uninitialized variable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- move cros_ec_dev to drivers/mfd
- other small maintenance fixes
[ The cros_ec_dev movement came in earlier through the MFD tree - Linus ]
* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: Use proper protocol transfer function
platform/chrome: cros_ec_lpc: Add support for Google Glimmer
platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
platform/chrome: cros_ec_lpc: remove redundant pointer request
cros_ec: fix nul-termination for firmware build info
platform/chrome: chromeos_laptop: make chromeos_laptop const
|
|
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
|
|
It adds support for new Mellanox system types of basic classes qmb7, sn34,
sn37, containing systems QMB700 (40x200GbE InfiniBand switch), SN3700
(32x200GbE and 16x400GbE Ethernet switch) and SN3410 (6x400GbE plus
48x50GbE Ethernet switch). These are the Top of the Rack systems, equipped
with Mellanox COM-Express carrier board and switch board with Mellanox
Quantum device, which supports InfiniBand switching with 40X200G ports and
line rate of up to HDR speed or with Mellanox Spectrum-2 device, which
supports Ethernet switching with 32X200G ports line rate of up to HDR
speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
It adds support for new Mellanox system types of basic half unit size
class msn201x, containing system MSN2010 (18x10GbE plus 4x4x25GbE) half
and its derivatives. This is the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
It adds support for new Mellanox system types of basic class msn274x,
containing system MSN2740 (32x100GbE Ethernet switch with cost reduction)
and its derivatives. These are the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights include:
- numerous target-core-user improvements related to queue full and
timeout handling. (MNC)
- prevent target-core-user corruption when invalid data page is
requested. (MNC)
- add target-core device action configfs attributes to allow
user-space to trigger events separate from existing attributes
exposed to end-users. (MNC)
- fix iscsi-target NULL pointer dereference 4.6+ regression in CHAP
error path. (David Disseldorp)
- avoid target-core backend UNMAP callbacks if range is zero. (Andrei
Vagin)
- fix a iscsi-target 4.14+ regression related multiple PDU logins,
that was exposed due to removal of TCP prequeue support. (Florian
Westphal + MNC)
Also, there is a iser-target bug still being worked on for post -rc1
code to address a long standing issue resulting in persistent
ib_post_send() failures, for RNICs with small max_send_sge"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
iscsi-target: make sure to wake up sleeping login worker
tcmu: Fix trailing semicolon
tcmu: fix cmd user after free
target: fix destroy device in target_configure_device
tcmu: allow userspace to reset ring
target core: add device action configfs files
tcmu: fix error return code in tcmu_configure_device()
target_core_user: add cmd id to broken ring message
target: add SAM_STAT_BUSY sense reason
tcmu: prevent corruption when invalid data page requested
target: don't call an unmap callback if a range length is zero
target/iscsi: avoid NULL dereference in CHAP auth error path
cxgbit: call neigh_event_send() to update MAC address
target: tcm_loop: Use seq_puts() in tcm_loop_show_info()
target: tcm_loop: Delete an unnecessary return statement in tcm_loop_submission_work()
target: tcm_loop: Delete two unnecessary variable initialisations in tcm_loop_issue_tmr()
target: tcm_loop: Combine substrings for 26 messages
target: tcm_loop: Improve a size determination in two functions
target: tcm_loop: Delete an error message for a failed memory allocation in four functions
sbp-target: Delete an error message for a failed memory allocation in three functions
...
|
|
Pull fbdev fix from Bartlomiej Zolnierkiewicz:
"Fix building of the omapfb driver (Tomi Valkeinen)"
* tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux:
video: omapfb: fix missing #includes
|
|
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes: 2863c61334aa ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db10337 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db10337 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Only five small fixes for issues when running under Xen"
* tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix {set,clear}_foreign_p2m_mapping on autotranslating guests
pvcalls-back: do not return error on inet_accept EAGAIN
xen-netfront: Fix race between device setup and open
xen/grant-table: Use put_page instead of free_page
x86/xen: init %gs very early to avoid page faults with stack protector
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
"The main thing in this merge is the defense for the Spectre
vulnerabilities. But there are other updates as well, the changes in
more detail:
- An s390 specific implementation of the array_index_mask_nospec
function to the defense against spectre v1
- Two patches to utilize the new PPA-12/PPA-13 instructions to run
the kernel and/or user space with reduced branch predicton.
- The s390 variant of the 'retpoline' spectre v2 defense called
'expoline'. There is no return instruction for s390, instead an
indirect branch is used for function return
The s390 defense mechanism for indirect branches works by using an
execute-type instruction with the indirect branch as the target of
the execute. In effect that turns off the prediction for the
indirect branch.
- Scrub registers in entry.S that contain user controlled values to
prevent the speculative use of these values.
- Re-add the second parameter for the s390 specific runtime
instrumentation system call and move the header file to uapi. The
second parameter will continue to do nothing but older kernel
versions only accepted valid real-time signal numbers. The details
will be documented in the man-page for the system call.
- Corrections and improvements for the s390 specific documentation
- Add a line to /proc/sysinfo to display the CPU model dependent
license-internal-code identifier
- A header file include fix for eadm.
- An error message fix in the kprobes code.
- The removal of an outdated ARCH_xxx select statement"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kconfig: Remove ARCH_WANTS_PROT_NUMA_PROT_NONE select
s390: introduce execute-trampolines for branches
s390: run user space and KVM guests with modified branch prediction
s390: add options to change branch prediction behaviour for the kernel
s390/alternative: use a copy of the facility bit mask
s390: add optimized array_index_mask_nospec
s390: scrub registers on kernel entry and KVM exit
s390/cio: fix kernel-doc usage
s390/runtime_instrumentation: re-add signum system call parameter
s390/cpum_cf: correct counter number of LAST_HOST_TRANSLATIONS
s390/kprobes: Fix %p uses in error messages
s390/runtime instrumentation: provide uapi header file
s390/sysinfo: add and display licensed internal code identifier
s390/docs: reword airq section
s390/docs: mention subchannel types
s390/cmf: fix kerneldoc
s390/eadm: fix CONFIG_BLOCK include dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision 20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups and removal of the no longer
needed at32ap-cpufreq driver.
Specifics:
- Drop the at32ap-cpufreq driver which is useless after the removal
of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in the
cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver for
AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX (Akshu
Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson)"
* tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
arm: imx: Add MODULE_ALIAS for cpufreq
cpufreq: Add and use cpufreq_for_each_{valid_,}entry_idx()
cpufreq: intel_pstate: Enable HWP during system resume on CPU0
cpufreq: scpi: fix error return code in scpi_cpufreq_init()
x86: hibernate: fix swsusp_arch_resume() prototype
PM / domains: Fix up domain-idle-states OF parsing
cpufreq: scpi: fix static checker warning cdev isn't an ERR_PTR
cpufreq: remove at32ap-cpufreq
cpufreq: AMD: Ignore the check for ProcFeedback in ST/CZ
x86: PM: Make APM idle driver initialize polling state
cpufreq: Skip cpufreq resume if it's not suspended
|
|
The omapfb driver fails to build after commit 23c35f48f5fb
("pinctrl: remove include file from <linux/device.h>") because it
relies on the <linux/pinctrl/consumer.h> and <linux/seq_file.h>
being pulled in by the <linux/device.h> header implicitly.
Include these headers explicitly to avoid the build failures.
Fixes: 23c35f48f5fb ("pinctrl: remove include file from <linux/device.h>")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
[b.zolnierkie: fix include order and patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Add dedicated structure with power cable setting for Mellanox msn21xx
family. These systems do not have a physical device for the power unit
controller. When the power cable is inserted or removed, the relevant
interrupt signal is handled, the status is updated, but no device is
associated with the signal.
Add definition for interrupt low aggregation signal. On system from
msn21xx family, low aggregation mask should be removed in order to allow
signal to hit CPU.
Fixes: 6613d18e9038 ("platform/x86: mlx-platform: Move module from arch/x86")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add define for the negative bus ID in order to use it in case no hotplug
device is associated with the hotplug interrupt signal. In this case,
the signal will be handled by the mlxreg-hotplug driver, but no device
will be associated with the signal.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add defines for the bus IDs, used for hotplug device topology to improve
code readability. Defines added for FAN and power units.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
With gcc-4.1.2:
drivers/platform/mellanox/mlxreg-hotplug.c: In function ‘mlxreg_hotplug_health_work_helper’:
drivers/platform/mellanox/mlxreg-hotplug.c:347: warning: ‘ret’ is used uninitialized in this function
Indeed, if mlxreg_core_item.count is zero, ret is used uninitialized.
While this is unlikely to happen (it is set to ARRAY_SIZE(...) in x86
board files), this is done in another source file, so fix this by
preinitializing ret to zero.
Fixes: c6acad68eb2dbffd ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.
Fixes: 84a527a41f38 ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Cavium thunder nicvf driver supports rx/tx rings of up to 65536 entries per.
The number of entires are stored in the q_len member of struct q_desc_mem. The
problem is that q_len being a u16, results in 65536 becoming 0.
In getting pointers to descriptors in the rings, the driver uses q_len minus 1
as a mask after incrementing the pointer, in order to go back to the beginning
and not go past the end of the ring.
With the q_len set to 0 the mask is no longer correct and the driver does go
beyond the end of the ring, causing various ills. Usually the first thing that
shows up is a "NETDEV WATCHDOG: enP2p1s0f1 (nicvf): transmit queue 7 timed out"
warning.
This patch remedies the problem by changing q_len to a u32.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While handling a driver reset we get a H_CLOSED return trying
to send a CRQ event. When this occurs we need to queue up another
reset attempt. Without doing this we see instances where the driver
is left in a closed state because the reset failed and there is no
further attempts to reset the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add suffix ULL to constants 272, 204, 136 and 68 in order to give the
compiler complete information about the proper arithmetic to use.
Notice that these constants are used in contexts that expect
expressions of type unsigned long long (64 bits, unsigned).
The following expressions are currently being evaluated using 32-bit
arithmetic:
272 * mult
204 * mult
136 * mult
68 * mult
Addresses-Coverity-ID: 201058
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time there are not a lot of changes coming from the IOMMU side.
That is partly because I returned from my parental leave late in the
development process and probably partly because everyone was busy with
Spectre and Meltdown mitigation work and didn't find the time for
IOMMU work. So here are the few changes that queued up for this merge
window:
- 5-level page-table support for the Intel IOMMU.
- error reporting improvements for the AMD IOMMU driver
- additional DT bindings for ipmmu-vmsa (Renesas)
- small fixes and cleanups"
* tag 'iommu-updates-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Clean up of_iommu_init_fn
iommu/ipmmu-vmsa: Remove redundant of_iommu_init_fn hook
iommu/msm: Claim bus ops on probe
iommu/vt-d: Enable 5-level paging mode in the PASID entry
iommu/vt-d: Add a check for 5-level paging support
iommu/vt-d: Add a check for 1GB page support
iommu/vt-d: Enable upto 57 bits of domain address width
iommu/vt-d: Use domain instead of cache fetching
iommu/exynos: Don't unconditionally steal bus ops
iommu/omap: Fix debugfs_create_*() usage
iommu/vt-d: clean up pr_irq if request_threaded_irq fails
iommu: Check the result of iommu_group_get() for NULL
iommu/ipmmu-vmsa: Add r8a779(70|95) DT bindings
iommu/ipmmu-vmsa: Add r8a7796 DT binding
iommu/amd: Set the device table entry PPR bit for IOMMU V2 devices
iommu/amd - Record more information about unknown events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia
Pull pcmcia updates from Dominik Brodowski:
"The linux-pcmcia mailing list was shut down, so offer an alternative
path for patches in MAINTAINERS.
Also, throw in two odd fixes for the pcmcia subsystem"
* 'pcmcia' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia:
pcmcia: soc_common: Handle return value of clk_prepare_enable
pcmcia: use proper printk format for resource
pcmcia: remove mailing list, update MAINTAINERS
|
|
git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"Ben missed sending his nouveau tree, but he really didn't have much
stuff in it:
- GP108 acceleration support is enabled by "secure boot" support
- some clockgating work on Kepler, and bunch of fixes
- the bulk of the diff is regenerated firmware files, the change to
them really isn't that large.
Otherwise this contains regular Intel and AMDGPU fixes"
* tag 'drm-for-v4.16-part2-fixes' of git://people.freedesktop.org/~airlied/linux: (59 commits)
drm/i915/bios: add DP max link rate to VBT child device struct
drm/i915/cnp: Properly handle VBT ddc pin out of bounds.
drm/i915/cnp: Ignore VBT request for know invalid DDC pin.
drm/i915/cmdparser: Do not check past the cmd length.
drm/i915/cmdparser: Check reg_table_count before derefencing.
drm/i915/bxt, glk: Increase PCODE timeouts during CDCLK freq changing
drm/i915/gvt: Use KVM r/w to access guest opregion
drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on
drm/i915/gvt: only reset execlist state of one engine during VM engine reset
drm/i915/gvt: refine intel_vgpu_submission_ops as per engine ops
drm/amdgpu: re-enable CGCG on CZ and disable on ST
drm/nouveau/clk: fix gcc-7 -Wint-in-bool-context warning
drm/nouveau/mmu: Fix trailing semicolon
drm/nouveau: Introduce NvPmEnableGating option
drm/nouveau: Add support for SLCG for Kepler2
drm/nouveau: Add support for BLCG on Kepler2
drm/nouveau: Add support for BLCG on Kepler1
drm/nouveau: Add support for basic clockgating on Kepler1
drm/nouveau/kms/nv50: fix handling of gamma since atomic conversion
drm/nouveau/kms/nv50: use INTERPOLATE_257_UNITY_RANGE LUT on newer chipsets
...
|
|
Pull ceph updates from Ilya Dryomov:
"Things have been very quiet on the rbd side, as work continues on the
big ticket items slated for the next merge window.
On the CephFS side we have a large number of cap handling
improvements, a fix for our long-standing abuse of ->journal_info in
ceph_readpages() and yet another dentry pointer management patch"
* tag 'ceph-for-4.16-rc1' of git://github.com/ceph/ceph-client:
ceph: improving efficiency of syncfs
libceph: check kstrndup() return value
ceph: try to allocate enough memory for reserved caps
ceph: fix race of queuing delayed caps
ceph: delete unreachable code in ceph_check_caps()
ceph: limit rate of cap import/export error messages
ceph: fix incorrect snaprealm when adding caps
ceph: fix un-balanced fsc->writeback_count update
ceph: track read contexts in ceph_file_info
ceph: avoid dereferencing invalid pointer during cached readdir
ceph: use atomic_t for ceph_inode_info::i_shared_gen
ceph: cleanup traceless reply handling for rename
ceph: voluntarily drop Fx cap for readdir request
ceph: properly drop caps for setattr request
ceph: voluntarily drop Lx cap for link/rename requests
ceph: voluntarily drop Ax cap for requests that create new inode
rbd: whitelist RBD_FEATURE_OPERATIONS feature bit
rbd: don't NULL out ->obj_request in rbd_img_obj_parent_read_full()
rbd: use kmem_cache_zalloc() in rbd_img_request_create()
rbd: obj_request->completion is unused
|
|
When using devmap to redirect packets between interfaces,
xdp_do_flush() is usually a must to flush any batched
packets. Unfortunately this is missed in current tuntap
implementation.
Unlike most hardware driver which did XDP inside NAPI loop and call
xdp_do_flush() at then end of each round of poll. TAP did it in the
context of process e.g tun_get_user(). So fix this by count the
pending redirected packets and flush when it exceeds NAPI_POLL_WEIGHT
or MSG_MORE was cleared by sendmsg() caller.
With this fix, xdp_redirect_map works again between two TAPs.
Fixes: 761876c857cb ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"As I mentioned in the last pull request, there's a second batch of
security updates for arm64 with mitigations for Spectre/v1 and an
improved one for Spectre/v2 (via a newly defined firmware interface
API).
Spectre v1 mitigation:
- back-end version of array_index_mask_nospec()
- masking of the syscall number to restrict speculation through the
syscall table
- masking of __user pointers prior to deference in uaccess routines
Spectre v2 mitigation update:
- using the new firmware SMC calling convention specification update
- removing the current PSCI GET_VERSION firmware call mitigation as
vendors are deploying new SMCCC-capable firmware
- additional branch predictor hardening for synchronous exceptions
and interrupts while in user mode
Meltdown v3 mitigation update:
- Cavium Thunder X is unaffected but a hardware erratum gets in the
way. The kernel now starts with the page tables mapped as global
and switches to non-global if kpti needs to be enabled.
Other:
- Theoretical trylock bug fixed"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (38 commits)
arm64: Kill PSCI_GET_VERSION as a variant-2 workaround
arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support
arm/arm64: smccc: Implement SMCCC v1.1 inline primitive
arm/arm64: smccc: Make function identifiers an unsigned quantity
firmware/psci: Expose SMCCC version through psci_ops
firmware/psci: Expose PSCI conduit
arm64: KVM: Add SMCCC_ARCH_WORKAROUND_1 fast handling
arm64: KVM: Report SMCCC_ARCH_WORKAROUND_1 BP hardening support
arm/arm64: KVM: Turn kvm_psci_version into a static inline
arm/arm64: KVM: Advertise SMCCC v1.1
arm/arm64: KVM: Implement PSCI 1.0 support
arm/arm64: KVM: Add smccc accessors to PSCI code
arm/arm64: KVM: Add PSCI_VERSION helper
arm/arm64: KVM: Consolidate the PSCI include files
arm64: KVM: Increment PC after handling an SMC trap
arm: KVM: Fix SMCCC handling of unimplemented SMC/HVC calls
arm64: KVM: Fix SMCCC handling of unimplemented SMC/HVC calls
arm64: entry: Apply BP hardening for suspicious interrupts from EL0
arm64: entry: Apply BP hardening for high-priority synchronous exceptions
arm64: futex: Mask __user pointers prior to dereference
...
|
|
Pull virtio/vhost updates from Michael Tsirkin:
"virtio, vhost: fixes, cleanups, features
This includes the disk/cache memory stats for for the virtio balloon,
as well as multiple fixes and cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: don't hold onto file pointer for VHOST_SET_LOG_FD
vhost: don't hold onto file pointer for VHOST_SET_VRING_ERR
vhost: don't hold onto file pointer for VHOST_SET_VRING_CALL
ringtest: ring.c malloc & memset to calloc
virtio_vop: don't kfree device on register failure
virtio_pci: don't kfree device on register failure
virtio: split device_register into device_initialize and device_add
vhost: remove unused lock check flag in vhost_dev_cleanup()
vhost: Remove the unused variable.
virtio_blk: print capacity at probe time
virtio: make VIRTIO a menuconfig to ease disabling it all
virtio/ringtest: virtio_ring: fix up need_event math
virtio/ringtest: fix up need_event math
virtio: virtio_mmio: make of_device_ids const.
firmware: Use PTR_ERR_OR_ZERO()
virtio-mmio: Use PTR_ERR_OR_ZERO()
vhost/scsi: Improve a size determination in four functions
virtio_balloon: include disk/file caches memory statistics
|
