| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since the serial core handles spin lock initialisation,
let the driver rely on it.
Depends-on: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is very unlikely for processor to speculate on the func_table index.
The index is uchar and func_table is of size 256. So the compiler would
need to screw up and generate a really bad code.
But to stay on the safe side, forbid speculation on this user passed
index.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Kosina <jikos@kernel.org>
Link: https://lore.kernel.org/r/20200730105546.24268-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Indeed according to the clk API if clk_round_rate() has successfully
accepted a rate, then in order setup the clock with value returned by the
clk_round_rate() the clk_set_rate() method must be called with the
original rate value.
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Really instead of twice checking the clk_round_rate() return value
we could do it once, and if it isn't error the clock rate can be changed.
By doing so we decrease a number of ret-value tests and remove a weird
goto-based construction implemented in the dw8250_set_termios() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split imx earlycon driver from imx serial driver "imx.c" as
separated driver. imx serial driver can be built as module,
but earlycon driver only support build in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-3-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for building i.MX serial driver as module.
The changes of the patch:
- imx console driver can be built as module.
- move out earlycon code to separated driver like imx_earlycon.c,
and imx earlycon driver only support build-in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 1355cba9c3ba ("tty/synclink: remove ISA support"), the
synlink driver only supports PCI card. Remove any leftover dead code
to support other cards.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200727130501.31005-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the preferred form for passing the size of a structure type. The
alternative form where the structure type is spelled out hurts
readability and introduces an opportunity for a bug when the object
type is changed but the corresponding object identifier to which the
sizeof operator is applied is not.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/b04dd8cdd67bd6ffde3fd12940aeef35fdb824a6.1595543280.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following checkpatch.pl warnings together with all the
identation issues in struct serial_struct32:
ERROR: code indent should use tabs where possible
+ char reserved_char;$
WARNING: please, no spaces at the start of a line
+ char reserved_char;$
ERROR: code indent should use tabs where possible
+ compat_int_t reserved;$
WARNING: please, no spaces at the start of a line
+ compat_int_t reserved;$
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/77576843397aeab0af8aa0423a9768f3ca8dedfb.1595543280.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
One-element arrays are being deprecated[1]. Replace the one-element arrays
with simple value types 'char reserved_char' and 'compat_int_t reserved'[2],
once it seems these are just placeholders for alignment.
[1] https://github.com/KSPP/linux/issues/79
[2] https://github.com/KSPP/linux/issues/86
Tested-by: kernel test robot <lkp@intel.com>
Link: https://github.com/GustavoARSilva/linux-hardening/blob/master/cii/0-day/tty-20200716.md
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/f49bf0e27eaac396c96d21392c8c284f9f5ef52a.1595543280.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
we need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into master
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.8-rc7
They include:
- habanalabs fixes
- tiny fpga driver fixes
- /dev/mem fixup from previous changes
- interconnect driver fixes
- binder fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
interconnect: msm8916: Fix buswidth of pcnoc_s nodes
interconnect: Do not skip aggregation for disabled paths
/dev/mem: Add missing memory barriers for devmem_inode
binder: Don't use mmput() from shrinker function.
habanalabs: prevent possible out-of-bounds array access
fpga: dfl: fix bug in port reset handshake
fpga: dfl: pci: reduce the scope of variable 'ret'
habanalabs: set 4s timeout for message to device CPU
habanalabs: set clock gating per engine
habanalabs: block WREG_BULK packet on PDMA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into master
Pull driver core fix from Greg KH:
"A single driver core fix for 5.8-rc7. It resolves a problem found in
the previous fix for this code made in 5.8-rc6. Hopefully this is all
now cleared up, as this seems to be the last of the reported issues in
this area, and was tested on the problem hardware.
This patch has been in linux-next with no reported problems"
* tag 'driver-core-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
device property: Avoid NULL pointer dereference in device_get_next_child_node()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into master
Pull staging driver fixes from Greg KH:
"Five small staging driver fixes for 5.8-rc7 to resolve some reported
problems:
- four comedi driver fixes for problems found with them
- a syzbot-found fix for the wlang-ng driver that resolves a much
reported problem.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wlan-ng: properly check endpoint types
staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty and serial and fbcon fixes for 5.8-rc7 to
resolve some reported issues.
The fbcon fix is in here as it was simpler to take it this way (and it
was acked by the maintainer) as it was related to the vt console fix
as well, both of which resolve syzbot-found issues in the console
handling code.
The other serial driver fixes are for small issues reported in the -rc
releases.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X
fbdev: Detect integer underflow at "struct fbcon_ops"->clear_margins.
serial: 8250_mtk: Fix high-speed baud rates clamping
serial: 8250: fix null-ptr-deref in serial8250_start_tx()
serial: tegra: drop bogus NULL tty-port checks
serial: tegra: fix CREAD handling for PIO
tty: xilinx_uartps: Really fix id assignment
vt: Reject zero-sized screen buffer size.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into master
Pull USB fixes from Greg KH:
"Three small USB XHCI driver fixes for 5.8-rc7.
They all resolve some minor issues that have been reported on some
different platforms.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: tegra: Fix allocation for the FPCI context
usb: xhci: Fix ASM2142/ASM3142 DMA addressing
usb: xhci-mtk: fix the failure of bandwidth allocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi into master
Pull SCSI fix from James Bottomley:
"Small core patch to fix a corner case bug: we forgot to run the queues
to handle starvation in the error exit from the scsi_queue_rq routine,
which can lead to hangs on error conditions"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Run queue in case of I/O resource contention failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull timer fix from Ingo Molnar:
"Fix a suspend/resume regression (crash) on TI AM3/AM4 SoC's"
* tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull EFI fixes from Ingo Molnar:
"Various EFI fixes:
- Fix the layering violation in the use of the EFI runtime services
availability mask in users of the 'efivars' abstraction
- Revert build fix for GCC v4.8 which is no longer supported
- Clean up some x86 EFI stub details, some of which are borderline
bugs that copy around garbage into padding fields - let's fix these
out of caution.
- Fix build issues while working on RISC-V support
- Avoid --whole-archive when linking the stub on arm64"
* tag 'efi-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Revert "efi/x86: Fix build with gcc 4"
efi/efivars: Expose RT service availability via efivars abstraction
efi/libstub: Move the function prototypes to header file
efi/libstub: Fix gcc error around __umoddi3 for 32 bit builds
efi/libstub/arm64: link stub lib.a conditionally
efi/x86: Only copy upto the end of setup_header
efi/x86: Remove unused variables
|
|
Pull networking fixes from David Miller:
1) Fix RCU locaking in iwlwifi, from Johannes Berg.
2) mt76 can access uninitialized NAPI struct, from Felix Fietkau.
3) Fix race in updating pause settings in bnxt_en, from Vasundhara
Volam.
4) Propagate error return properly during unbind failures in ax88172a,
from George Kennedy.
5) Fix memleak in adf7242_probe, from Liu Jian.
6) smc_drv_probe() can leak, from Wang Hai.
7) Don't muck with the carrier state if register_netdevice() fails in
the bonding driver, from Taehee Yoo.
8) Fix memleak in dpaa_eth_probe, from Liu Jian.
9) Need to check skb_put_padto() return value in hsr_fill_tag(), from
Murali Karicheri.
10) Don't lose ionic RSS hash settings across FW update, from Shannon
Nelson.
11) Fix clobbered SKB control block in act_ct, from Wen Xu.
12) Missing newlink in "tx_timeout" sysfs output, from Xiongfeng Wang.
13) IS_UDPLITE cleanup a long time ago, incorrectly handled
transformations involving UDPLITE_RECV_CC. From Miaohe Lin.
14) Unbalanced locking in netdevsim, from Taehee Yoo.
15) Suppress false-positive error messages in qed driver, from Alexander
Lobakin.
16) Out of bounds read in ax25_connect and ax25_sendmsg, from Peilin Ye.
17) Missing SKB release in cxgb4's uld_send(), from Navid Emamdoost.
18) Uninitialized value in geneve_changelink(), from Cong Wang.
19) Fix deadlock in xen-netfront, from Andera Righi.
19) flush_backlog() frees skbs with IRQs disabled, so should use
dev_kfree_skb_irq() instead of kfree_skb(). From Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
drivers/net/wan: lapb: Corrected the usage of skb_cow
dev: Defer free of skbs in flush_backlog
qrtr: orphan socket in qrtr_release()
xen-netfront: fix potential deadlock in xennet_remove()
flow_offload: Move rhashtable inclusion to the source file
geneve: fix an uninitialized value in geneve_changelink()
bonding: check return value of register_netdevice() in bond_newlink()
tcp: allow at most one TLP probe per flight
AX.25: Prevent integer overflows in connect and sendmsg
cxgb4: add missing release on skb in uld_send()
net: atlantic: fix PTP on AQC10X
AX.25: Prevent out-of-bounds read in ax25_sendmsg()
sctp: shrink stream outq when fails to do addstream reconf
sctp: shrink stream outq only when new outcnt < old outcnt
AX.25: Fix out-of-bounds read in ax25_connect()
enetc: Remove the mdio bus on PF probe bailout
net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offload
net: ethernet: ave: Fix error returns in ave_init
drivers/net/wan/x25_asy: Fix to make it work
ipvs: fix the connection sync failed in some cases
...
|
|
This patch fixed 2 issues with the usage of skb_cow in LAPB drivers
"lapbether" and "hdlc_x25":
1) After skb_cow fails, kfree_skb should be called to drop a reference
to the skb. But in both drivers, kfree_skb is not called.
2) skb_cow should be called before skb_push so that is can ensure the
safety of skb_push. But in "lapbether", it is incorrectly called after
skb_push.
More details about these 2 issues:
1) The behavior of calling kfree_skb on failure is also the behavior of
netif_rx, which is called by this function with "return netif_rx(skb);".
So this function should follow this behavior, too.
2) In "lapbether", skb_cow is called after skb_push. This results in 2
logical issues:
a) skb_push is not protected by skb_cow;
b) An extra headroom of 1 byte is ensured after skb_push. This extra
headroom has no use in this function. It also has no use in the
upper-layer function that this function passes the skb to
(x25_lapb_receive_frame in net/x25/x25_dev.c).
So logically skb_cow should instead be called before skb_push.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into master
Pull PCI fixes from Bjorn Helgaas:
- Reject invalid IRQ 0 command line argument for virtio_mmio because
IRQ 0 now generates warnings (Bjorn Helgaas)
- Revert "PCI/PM: Assume ports without DLL Link Active train links in
100 ms", which broke nouveau (Bjorn Helgaas)
* tag 'pci-v5.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms"
virtio-mmio: Reject invalid IRQ 0 command line argument
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:
1. state = read bus state
2. if state is not "Closed":
3. request to set state to "Closing"
4. wait for state to be set to "Closing"
5. request to set state to "Closed"
6. wait for state to be set to "Closed"
If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".
Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.
Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu into master
Pull iommu fix from Joerg Roedel:
"Fix a NULL-ptr dereference in the QCOM IOMMU driver"
* tag 'iommu-fix-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/qcom: Use domain rather than dev as tlb cookie
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma into master
Pull rdma fixes from Jason Gunthorpe:
"One merge window regression, some corruption bugs in HNS and a few
more syzkaller fixes:
- Two long standing syzkaller races
- Fix incorrect HW configuration in HNS
- Restore accidentally dropped locking in IB CM
- Fix ODP prefetch bug added in the big rework several versions ago"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Prevent prefetch from racing with implicit destruction
RDMA/cm: Protect access to remote_sidr_table
RDMA/core: Fix race in rdma_alloc_commit_uobject()
RDMA/hns: Fix wrong PBL offset when VA is not aligned to PAGE_SIZE
RDMA/hns: Fix wrong assignment of lp_pktn_ini in QPC
RDMA/mlx5: Use xa_lock_irq when access to SRQ table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm into master
Pull device mapper fix from Mike Snitzer:
"A stable fix for DM integrity target's integrity recalculation that
gets skipped when resuming a device. This is a fix for a previous
stable@ fix"
* tag 'for-5.8/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm integrity: fix integrity recalculation that is improperly skipped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into master
Pull i2c fixes from Wolfram Sang:
"Again some driver bugfixes and some documentation fixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-qcom-geni: Fix DMA transfer race
i2c: rcar: always clear ICSAR to avoid side effects
MAINTAINERS: i2c: at91: handover maintenance to Codrin Ciubotariu
i2c: drop duplicated word in the header file
i2c: cadence: Clear HOLD bit at correct time in Rx path
Revert "i2c: cadence: Fix the hold bit setting"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc into master
Pull MMC fix from Ulf Hansson:
"Fix clock divider calculation in the ASPEED SDHCI controller"
* tag 'mmc-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-aspeed: Fix clock divider calculation
|
|
into master
Pull drm fixes from Dave Airlie:
"Quiet fixes, I may have a single regression fix follow up to this for
nouveau, but it might be next week, Ben was testing it a bit more .
Otherwise two amdgpu fixes, one lima and one sun4i:
amdgpu:
- Fix crash when overclocking VegaM
- Fix possible crash when editing dpm levels
sun4i:
- Fix inverted HPD result; fixes an earlier fix
lima:
- fix timeout during reset"
* tag 'drm-fixes-2020-07-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Fix NULL dereference in dpm sysfs handlers
drm/amd/powerplay: fix a crash when overclocking Vega M
drm/lima: fix wait pp reset timeout
drm: sun4i: hdmi: Fix inverted HPD result
|
|
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add sparse context annotation to the receive handlers, which release and
reacquire the port lock, to silence sparse warnings:
drivers/tty/serial/msm_serial.c:748:25: warning: context imbalance in 'msm_handle_rx_dm' - unexpected unlock
drivers/tty/serial/msm_serial.c:814:28: warning: context imbalance in 'msm_handle_rx' - unexpected unlock
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add sparse context annotation to the receive handler, which releases and
reacquires the port lock, to silence a sparse warning:
drivers/tty/serial/pmac_zilog.c:255:36: sparse: sparse: context imbalance in 'pmz_receive_chars' - unexpected unlock
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 28bc24fc46f9 (vc: separate state), vc->vc_color is known as
vc->state.color. Somehow both me and 0-day bot missed this driver during
the conversion.
So fix the driver now.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 28bc24fc46f9 ("vc: separate state")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200724062735.18229-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347e4 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Very similar to commit 544f287b8495
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit adc0daad366b62ca1bce3e2958a40b0b71a8b8b3 ("dm: report suspended
device during destroy") broke integrity recalculation.
The problem is dm_suspended() returns true not only during suspend,
but also during resume. So this race condition could occur:
1. dm_integrity_resume calls queue_work(ic->recalc_wq, &ic->recalc_work)
2. integrity_recalc (&ic->recalc_work) preempts the current thread
3. integrity_recalc calls if (unlikely(dm_suspended(ic->ti))) goto unlock_ret;
4. integrity_recalc exits and no recalculating is done.
To fix this race condition, add a function dm_post_suspending that is
only true during the postsuspend phase and use it instead of
dm_suspended().
Signed-off-by: Mikulas Patocka <mpatocka redhat com>
Fixes: adc0daad366b ("dm: report suspended device during destroy")
Cc: stable vger kernel org # v4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When we have no primary fwnode or when it's a software node, we may end up
in the situation when fwnode is a NULL pointer. There is no point to look for
secondary fwnode in such case. Add a necessary check to a condition.
Fixes: 114dbb4fa7c4 ("drivers property: When no children in primary, try secondary")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20200716182747.54929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting general protection fault in bitfill_aligned() [1]
caused by integer underflow in bit_clear_margins(). The cause of this
problem is when and how do_vc_resize() updates vc->vc_{cols,rows}.
If vc_do_resize() fails (e.g. kzalloc() fails) when var.xres or var.yres
is going to shrink, vc->vc_{cols,rows} will not be updated. This allows
bit_clear_margins() to see info->var.xres < (vc->vc_cols * cw) or
info->var.yres < (vc->vc_rows * ch). Unexpectedly large rw or bh will
try to overrun the __iomem region and causes general protection fault.
Also, vc_resize(vc, 0, 0) does not set vc->vc_{cols,rows} = 0 due to
new_cols = (cols ? cols : vc->vc_cols);
new_rows = (lines ? lines : vc->vc_rows);
exception. Since cols and lines are calculated as
cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres);
rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
cols /= vc->vc_font.width;
rows /= vc->vc_font.height;
vc_resize(vc, cols, rows);
in fbcon_modechanged(), var.xres < vc->vc_font.width makes cols = 0
and var.yres < vc->vc_font.height makes rows = 0. This means that
const int fd = open("/dev/fb0", O_ACCMODE);
struct fb_var_screeninfo var = { };
ioctl(fd, FBIOGET_VSCREENINFO, &var);
var.xres = var.yres = 1;
ioctl(fd, FBIOPUT_VSCREENINFO, &var);
easily reproduces integer underflow bug explained above.
Of course, callers of vc_resize() are not handling vc_do_resize() failure
is bad. But we can't avoid vc_resize(vc, 0, 0) which returns 0. Therefore,
as a band-aid workaround, this patch checks integer underflow in
"struct fbcon_ops"->clear_margins call, assuming that
vc->vc_cols * vc->vc_font.width and vc->vc_rows * vc->vc_font.heigh do not
cause integer overflow.
[1] https://syzkaller.appspot.com/bug?id=a565882df74fa76f10d3a6fec4be31098dbb37c6
Reported-and-tested-by: syzbot <syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200715015102.3814-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB
context save/restore") is using the IPFS 'num_offsets' value when
allocating memory for FPCI context instead of the FPCI 'num_offsets'.
After commit cad064f1bd52 ("devres: handle zero size in devm_kmalloc()")
was added system suspend started failing on Tegra186. The kernel log
showed that the Tegra XHCI driver was crashing on entry to suspend when
attempting the save the USB context. On Tegra186, the IPFS context has a
zero length but the FPCI content has a non-zero length, and because of
the bug in the Tegra XHCI driver we are incorrectly allocating a zero
length array for the FPCI context. The crash seen on entering suspend
when we attempt to save the FPCI context and following commit
cad064f1bd52 ("devres: handle zero size in devm_kmalloc()") this now
causes a NULL pointer deference when we access the memory. Fix this by
correcting the amount of memory we are allocating for FPCI contexts.
Cc: stable@vger.kernel.org
Fixes: 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB context save/restore")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200715113842.30680-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The buswidth of the pcnoc_s_* nodes is actually not 8, but
4 bytes. Let's fix it.
Reported-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Fixes: 30c8fa3ec61a ("interconnect: qcom: Add MSM8916 interconnect provider driver")
Link: https://lore.kernel.org/r/20200709130004.12462-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200723083735.5616-3-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When an interconnect path is being disabled, currently we don't aggregate
the requests for it afterwards. But the re-aggregation step shouldn't be
skipped, as it may leave the nodes with outdated bandwidth data. This
outdated data may actually keep the path still enabled and prevent the
device from going into lower power states.
Reported-by: Atul Dhudase <adhudase@codeaurora.org>
Fixes: 7d374b209083 ("interconnect: Add helpers for enabling/disabling a path")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Atul Dhudase <adhudase@codeaurora.org>
Reviewed-by: Atul Dhudase <adhudase@codeaurora.org>
Link: https://lore.kernel.org/r/20200721120740.3436-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200723083735.5616-2-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WRITE_ONCE() isn't the correct way to publish a pointer to a data
structure, since it doesn't include a write memory barrier. Therefore
other tasks may see that the pointer has been set but not see that the
pointed-to memory has finished being initialized yet. Instead a
primitive with "release" semantics is needed.
Use smp_store_release() for this.
The use of READ_ONCE() on the read side is still potentially correct if
there's no control dependency, i.e. if all memory being "published" is
transitively reachable via the pointer itself. But this pairing is
somewhat confusing and error-prone. So just upgrade the read side to
smp_load_acquire() so that it clearly pairs with smp_store_release().
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 3234ac664a87 ("/dev/mem: Revoke mappings when a driver claims the region")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20200716060553.24618-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting that mmput() from shrinker function has a risk of
deadlock [1], for delayed_uprobe_add() from update_ref_ctr() calls
kzalloc(GFP_KERNEL) with delayed_uprobe_lock held, and
uprobe_clear_state() from __mmput() also holds delayed_uprobe_lock.
Commit a1b2289cef92ef0e ("android: binder: drop lru lock in isolate
callback") replaced mmput() with mmput_async() in order to avoid sleeping
with spinlock held. But this patch replaces mmput() with mmput_async() in
order not to start __mmput() from shrinker context.
[1] https://syzkaller.appspot.com/bug?id=bc9e7303f537c41b2b0cc2dfcea3fc42964c2d45
Reported-by: syzbot <syzbot+1068f09c44d151250c33@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+e5344baa319c9a96edec@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Acked-by: Todd Kjos <tkjos@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4ba9adb2-43f5-2de0-22de-f6075c1fab50@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.8-2020-07-22:
amdgpu:
- Fix crash when overclocking VegaM
- Fix possible crash when editing dpm levels
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723032608.3865-1-alexander.deucher@amd.com
|
